Search Documents

By J. A. Hillier

"IntroductionThe purpose of sampling is to remove a portion of material from a stream which is representative of it in size, moisture and mineral content.To prevent the effects of segregation, generally caused by the way in which a conveyor, pipe or launder is loaded or directed, the sampler should cut proportionally the entire cross section of the stream.If one conveyor transfers to another at a right angle, fines may be dropped on the near side, and the coarse material thrown to the opposite side. Segregation can also occur as a result of the motion of a conveyor belt passing over the idlers causing the coarse material to roll to the sides of the belt.When slurry changes direction of flow in a launder or pipe, the heavier and coarser fraction will centrifuge to the outside of the curve and tend to remain on one side of the stream. Similarly, if two streams joining in a common launder are not mixed at the point of confluence, they will continue down the launder unmixed . This effect is particularly noticeable in a plastic lined launder.Therefore, a proportional sample is usually accomplished by a constant rate of cutter travel across the entire stream, making certain that the cutter is not full or splashing over before reaching the end of travel.The cutter should operate on a constant interval based on time, tonnage and uniformity of flow. The opening should be at least three times the width of the largest piece to be sampled. The cutter width is more critical with ore samples where particle sizes are large. With slurry samples, the opening is usually much larger than the minimum in order to obtain sufficient samples"

Jan 1, 1989

By David W. Houston

The increasing energy crisis, coupled with stringent environ- mental regulations, has created new demands for high capacity materials handling systems with unit train transporting and continuing surveillance of quality control. Effective and efficient methods of material conveyance are through high speed, high volume conveyor belts with the monitoring of quality through the utilization of automatic sampling. When we speak of high speed, high volume belt discharges we are referring to speed ranges from 600 to 750 FPM and volumes as high as 5500 TPH. To achieve the optimum operating sampling system for high capacity belt discharges, it is imperative that two major design characteristics be investigated and evaluated; namely technical analysis of operating conditions through application of ASTM design criteria and practical experience in the selection of equipment and the design of related components. The task of obtaining a sample of reasonable weight to represent an entire lot presents a number of problems and emphasizes the necessity for using standard sampling procedures.

Jan 1, 1973

By Melvin W. Dadd

[One of the major problems in the purchase and sale of coal shipped in lake or ocean going vessels has always been the difficulty in obtaining a true analysis of the shipped coal?s quality because of faulty sampling by manual methods. As long as coal was sampled according to standards set up by ASTM methods designated D 492-48 there generally were no quarrels with the results obtained. However, due to varied weather conditions and because of the large number of cars sampled, there is no assurance that prescribed manual methods of sampling will always be followed. Because of this problem, the organization previously called American Coal Sales Association, now part of the National Coal Association, set up a committee compose of representatives from coal producers, coal shippers and coal consumers to study this sampling problem and to devise, if possible, a means of sampling on the high lift dumpers which could be automated so that a; true sample of the coal as loaded in the railroad car could be obtained.]

Jan 1, 1962

By M Wagner, H Assimi, F Neumann, C Garcia, B Koch

Run-of-Mine (ROM) stockpiles are the inventory of valuable materials extracted from the mine. Depending on the customer requests, a selective addition of ore from stockyards should be selected at the required tonnage. In the stockyard, stackers and reclaimers are the machines which load and unload ore, respectively. Currently, humans determine the reclaiming/stacking planning sequence in the stockyard by rules of thumb. However, this is a complex task subject to multiple operational constraints, such as where undesirable mineral properties should not exceed certain limits in a request. Human planning can lead to limited decision support and lower ability to consider the upcoming blends and requests. This kind of decision making can cause perturbations in the assumed profit and unexpected loss in practice. Therefore, an intelligent decision-maker and sequence planner would be highly valuable to automate stacking and reclaiming operations in practice. The benefits are reducing variability in decision-making and operation costs. This paper considers a stockyard with available mineral information in the stockpiles using load and dump locations from GPS data feeds. We present an optimisation problem to find a solution which results in reclaiming more ore in a shorter time. To solve the problem, we develop an automatic search strategy based on the greedy search algorithm independent of the type of machine used in reclaiming. The proposed method plans a sequence for stockyard recovery blend optimisation to meet multiple customer demands in a timeframe. Blend optimisation is subject to various constraints such as the elemental composition of the valuable materials and penalty elements. We present three case studies using EKA’s simulator, to fulfil two to four requests from four stockpiles. We compare the obtained results with a pilgrim step reclaiming heuristic and we show how our proposed search strategy outperforms the current strategy used in practice.

Nov 10, 2020

By W. X. Wang

In the mining and quarry industries, rock fragments are often transported by conveyor belt. To estimate the qualities of the rock fragments (i.e., size distribution and shape), an operator must take samples from the conveyor and manually perform a sieve analysis, which is time-consuming and tedious. Alternatively, an image-analysis system can be used to monitor the fragment quality on a fast moving conveyor belt. However, images of fragments on a fast moving belt vary to such a degree that the quality of any two successive images are not the same, and some of the images are of such poor quality that they are unrecognizable by human eyes. If poor-quality images are directly analyzed by a segmentation algorithm, the analysis will not be satisfactory. To resolve this problem, it is necessary to use an image-classification pro-gram for the automatic selection of fragment images with good quality. Because of this need, an image-classification program was developed and tested both in the laboratory and in the field. Testing of the system on different types of fragments showed that the system works reasonably well.

Jan 1, 1996

This paper describes a plant built at The Broken Hill Associated Smelters, Port Pirie to sample lead sinter automatically. As the plant is still in the commissioning stage results on the precision and accuracy of the sampling are not yet available, but some of the difficulties experienced during commissioning are discussed.

Jan 1, 1976

By H. Kroog

"This contribution reports recent mineral sorting experience and lists the possibilities of the newest generation of automatic mineral sorters with a special focus on electromagnetic detection, optoelectronic technology and the latest innovative X- Ray transmission units. In industry, mineral and ore are still hand-picked and current automation potential is only utilised in a handful of specific applications. Recently a number of technological developments took place that may increase sorting potential, save mill costs and lead to lower overall tonnage costs. The mentioned technologies provide automatic dry separation of minerals and rock as an alternative for conventional processing. The MikroSort technology is environmentally friendly:•,The remaining waste is free of contaminations•,The dump volume is reduced•,The concentration of the high grade material•,at an early stage saves resources"

Jan 1, 2005

By T. P. R. de Jong, H. Harbeck

"This contribution reports recent mineral sorting experience and lists the opportunities of the newest generation of automatic sorters with a special focus on electromagnetic detection and Xray transmission. With the available sensor resolutions and actuator systems that are available today sorting of minerals down to 2 mm size and up to 250 mm lump size is technically feasible. In industry, ore as well as coal is still hand-picked and current automation potential only utilised in a handful of specific applications. Recently a number of technological developments took place that may increase sorting potential, save mill costs and lead to lower overall tonnage costs.They are:??High speed and high resolution sorting systems based on X-ray transmission imaging??High speed on-line image processing and further development of advanced data processing??Modular multi-sensor automatic sorting units (using one or more sensors such as colour, electromagnetic and X-ray in a single device)??Sensitive electromagnetic sensors for sorting based on differences in magnetic susceptibility and electric conductivityThe above enables compact dry separation, insensitive for moisture fluctuations and at high separation sharpness, as well as “electronic” high gradient magnetic separation for larger particles. Besides conventional X-ray transmission (XRT), dual-energy XRT (DE-XRT) is now being redesigned to meet the requirements of the mining industry. The mentioned technologies provide automatic dry separation of minerals and rock as alternative for conventional processing."

Jan 1, 2005

By R. J. Wensley

THE use of small substations for the supplying of 275-volt energy to the locomotive and cutting machines in coal mines is a well-established practice. A few years ago, when labor costs were lower, these substations were located as near to the load as possible, and an operator was provided for each station. This practice has now become so expensive that substations are being located with reference to other mining machinery, such as hoists or pumps, so that one operator can look after both. Some-times the substation is operated by one whose duties make him traverse quite a large area. In such cases the interruption of alternating-current supply may produce a long interruption in the direct current, as the station cannot resume service until this man reaches it. Such interruptions interfere seriously with production and may easily counterbalance the supposed saving gained by such operating methods. The grouping of substations for convenience in operating may also result in excessive copper loss and consequently poor trolley voltage, with its attendant evils of low locomotive speeds and increased locomotive motor maintenance. The speed of the coal-cutting machines will also be reduced. By relieving the substation of its, burden of the operating labor cost, the most economical location, from an electrical standpoint, may be chosen. The matter of machine insurance should also be considered. If an attendant is caring for several kinds of equipment, he cannot watch the machine continually for signs of trouble; therefore, continued overload, phase failure, low alternating-current voltage, bearing trouble, etc. may result. Some partly automatic equipments have been installed; these have protection against low voltage, reverse current, and bearing trouble and are provided with automatic reclosing circuit breakers. This is a step in the right direction but it does not go far enough to give first-class machine insurance.

Jan 9, 1921

By T. A. Penzov

As a result of recent scientific and experimental studies new technical devices have been developed for monitoring and control the process of grinding. The description of microprocessor module MILLCONT 1 for control of the loading of the mill and microprocessor density control module DENSIMETER is given in the paper. The improved variant of the automatic system for ore grinding control in single-stage ball mill working in close cycle with a classifier with above mentioned technical means is shown in the paper. The loops for measuring and stabilization of the basic technological parameters (density of the ready pulp ? and fineness of grinding of the pulp ß) are described in the paper. The nowadays economic results in ore grinding process automation are given as well.

Jan 1, 2014

By Wolfgang Linden

The emerging demands on higher steel grades call for improvements in the operation of production units and a corresponding increase in automated processes, and therefore international steel producers require viable functions. The avoidance of slag carry-over to secondary metallurgy processes is essential for achieving steel grade qualities and reducing alloys in order to compensate slag residues in the downstream unit. The automatic tapping procedure in BOF converters will be supported by the implementation of reliable measurements used in high-end steel plants. Automatic tapping will help to achieve the following: Reduced slag carry-over, improved yield, increased reproducibility, improved working environment and safety and operation with minimum possible crew. The automatic tapping procedure is capable of being implemented in new or retrofitted installations.

Aug 17, 2017

By W. M. Aubrey

Lying approximately 110 miles east of Toronto, Canada, the Marmora mine produces iron ore with a content of about 40 pct Fe, primarily in the form of magnetite. Operated by the Marmoraton Mining Co., a subsidiary of Bethlehem Steel Co., the orebody is mined by open pit methods. The ore from the pit is crushed, cobbed, ground to -100 mesh, magnetically concentrated to 67 pct iron, and then pelletized in shaft furnaces. The pellets are normally shipped by rail throughout the year from Marmora to Picton on Lake Ontario where they are unloaded and stored. Subsequently, during the navigation season, the pellets are shipped to Bethlehem Steel's Lackawanna plant in Buffalo, New York, for use in the blast furnace. At Marmora, the pellet plant demand and the concentrator output are not usually equal. To counter this problem, surge capacity in the form of storage pits in combination with a 30-ft diam thick¬ener has been provided between the concentrator and the pellet plant. Two sets of controls have been installed on this thickener, one controlling the…

Jan 9, 1960

By Stone AM, Romensky G

The requirement for economic operation of unit trains carrying bulk materials has dictated that rapid and accurate bulk loading methods be provided. The train loading station at Phosphate Hill, built for Queensland Phosphate Ltd. to load rock phosphate, provides this facility and whilst the concept used is not unique, it contains a number of novel features that are considered to advance the "state of the art'' in this field. This paper briefly reviews some alternative concepts evaluated, and describes the design and operation of the scheme ultimately selected as being most appropriate to the project requirements. it is one which utilises a variable speed belt feeder whose speed is controlled in proportion to the weight rate of material moving on the belt as measured against a set point

Jan 1, 1978

By Young C. Kim

Because of the tremendous technological advances achieved in recent years in microcomputers, it is not only technically feasible but also economically viable to develop an automatic truck dispatching system using a microcomputer. Such an effort was initiated by the Department of mining and Geological Engineering, University of Arizona in the summer of 1983. Up to date results and experiences prove that today's microcomputers can be economically employed for such a system to be used at small to medium scale open-pit mines. An IBM/XT microcomputer with 10 MB harddisk storage, together with automatic sensing capability of truck movements at several key locations in the pit, formed the core of this system. System software is written primarily in MICROSOFT FORTRAN with supporting subroutines in MACRO assembly language. The software is designed to automatically monitor truck movement throughout the pit, to make heuristic assignments based on expected shovel availability and truck travel times, and to record production statistics. It is currently dimensioned to handle 50 trucks, 10 shovels, 10 dump sites and 3 material types. Due to the lack of funds to purchase the necessary communications hardware, the work related to the automatic sensing of truck movements has not been performed to date. Otherwise, the automatic truck dispatching-system is fully operational on a realtime mode.

Jan 1, 1984

By A. Rakshit, W. E. Kolb, Y. C. Kim

An IBM/XT microcomputer with 10 MB hard disk storage, together with automatic sensing capability of truck movements at several key locations in the pit, formed the core of this automatic truck dispatching system. System software is written primarily in MICROSOFT FORTRAN with supporting subroutines in MACRO assembly language. The software is designed to automatically monitor truck movement throughout the pit, to make heuristic assignments based on expected shovel availability and truck travel times, and to record production statistics. It is currently dimensioned to handle 50 trucks, 10 shovels, 10 dump sites, and three material types. Due to the lack of funds to purchase the necessary communications hardware, the work related to the automatic sensing of truck movements has not been performed to date. Otherwise, the system is fully operational on a realtime mode.

Jan 1, 1986

Nippon Telegraph and Telephone Corporation (NTT) developed a new construction method (the M-2 method) that could drive a long, curved small-diameter tunnel (4>1.2 m) without human labor. This method employs the cast-in-place lining system, using quick-hardening resin mortar, so that it can greatly increase the driving distance and execute both long distance driving (longer than 500 m) and curved driving with a radius of curvature of 200 m. Furthermore, the central control system with a mini-computer in a vertical shaft enables all work in a small-diameter tunnel, i.e., excavation, lining, and transportation of excavated soil and materials, without human labor. NTT conducted several field tests and a Practical Application Test (P.A.T.) under a public road bearing great traffic. Good results were obtained and the practicability of this method was demonstrated. Therefore, from now on, NTT will apply this ii-2 method to drive telecommunication cable tunnels in urban areas. This method will also be applicable to constructing public tunnel facilities, such as for water, sewage, electricity and gas.

Jan 1, 1987

By M D. Griffith

Oct 12, 2022

By Thomas L. Mell

Continuous processing plants handling liquids have achieved a high degree of centralized automatic control. Many chemical plants are operated from one room, with automatic control of the various process flow rates. These plants know from experience that automatic control can produce higher through-put, better uniformity of product, decreased operating costs and reduction of storage capacity, Plants which process materials in the form of bulk solids have not been able to use control to as great an extent, primarily due to the lack of measuring equipment capable of providing the same types of continuous automatic control available with liquid flow meters. This paper will describe a scale for measuring flows of bulk materials on conveyor belts which is particularly adaptable to remote centralized instrumentation and automatic control, and will also describe some typical control applications. Fig. 1 illustrates the basic method of measurement of this scale. A conveyor belt idler is supported on a rigid carriage which in turn is mounted in two anti- friction bearings on the conveyor stringers. The pivoted carriage is prevented from rotating about the pivot shaft by an electric strain gauge load cell connected between the carriage and a cross support. Increasing load on the conveyor belt increases the moment of the carriage frame about the pivot shaft, and proportionally increases the tension in the load cell. The belt speed is measured by a conventional d. c. tachometer generator driven from a pulley, usually on the return belt. The speed signal from the tachometer generator and the load signal from the load cell are combined to produce a signal proportional to the flow rate of material in tons per hour, or lbs. per foot, or equivalent units, It will be important to remember, in considering various control applications, that the flow rate of material on the belt is composed of these two component signals, namely the weight of material and the speed at which it is moving. The feed rate is then indicated and recorded by a self-balancing potentiometer of the type used for measuring temperature by means of thermocouples. These instruments may also be equipped with integrating mechanisms reading the totalized tonnage over a period of time.

Jan 1, 1958

By Agne Rustan

INTRODUCTION This work is a continuation of the preparatory study by Rustan and Stöckel 1979 (3) and (4) of the possibilities to introduce automatic mine ventilation in Swedish mines and construction works. The preparatory study has been financed by the Swedish Board of Technical Development. In the study it was recommended that an automatic step by step control of the fans near the working place due to diesel exhaust emission would be the best solution. A more advanced alternative would be to regulate the fresh air continuously in proportion to the contamination. The latter alternative has been studied by Boliden Mineral Co in the Udden mine. In this study it was found that the air supply could be regulated continuously but it was very important where the sensors feeling the contamination were placed. An intense study of the environment underground is now being planned by our division together with specialists from the National Board of Health and Safety, The Swedish Work Environment Fund, LKAB and the local Governmental Inspection of the Workers Safety. Different gases, radon, dust, airspeed, moisture temperature and pressure is planned to be measured continuously and correlation between the parameters is going to be established to decide the best measurement parameters for regulating the system. The best situation of sensors is also going to be studied. Despite this work hasn't been done yet this paper covers some of the problems which could be encounted with continuous regulation. In this report the environment has been studied during the test with step by step regulation of fans by radio. Diesel vehicles are the largest polluters under ground in Swedish mines and we have therefore suggested that the large diesel vehicles should regulate the fans. The goal of this study has therefore been to find how active diesel vehicles should be able to start and stop gallery fans at both intake and return air. In this paper different methods for activating fans are discussed. Then the best methods are chosen and tested in the mine. In this study we have found that changes of temperature is a cheap and effective method to start and stop cross cut fans in sublevel caving and radio signals seem to be an attractive system for start and stop of gallery fans. This work has been done in close collaboration between LKAB in Kiruna and the University of Luleå - Division of Electronics and Division of Mining and Rock Excavation. A reference group for the project has been established with ventilation experts from the mines, representatives for the local mine worker's unions and authorities from the local Governmental Inspection of the Workers Safety. VENTILATION SYSTEM STUDIED In the project the ventilation system at LKAB in Kiruna has been studied. The mining method used is sublevel caving with 9-13 m slice height. The air is heated winter time over ground by hot water heat exchanger. The main fans are pushing air down to a main distribution level along the 4000 m long and about 100 m wide orebody. From the distribution level, air is taken through shafts down to the sublevels, where it is pushed through the levels by local gallery fans on both intake and return side, see fig 1. The air ( ~ 8 m3/s) is moving freely through the gallery head. The cross cuts are ventilated with smaller fans, diameter 500 mm, and flexible duct, see fig 2. The aim of this study has been to study how to start and stop gallery- and cross fans and examine the environment when the fans are stopped . In Sweden there are no regulations telling that a minimum of air amount must be supplied. Instead the hygienic limits must be fullfilled.

Jan 1, 1981

A computer simulation of the automatic control of continuous mining machines has been prepared, similar to previous simulations of longwall mining systems and coal thickness sensors. The simulation allows for programmed variation of the horizon detection method, the azimuthal guidance system, the type and configuration of the miner, varying hardness in the unmined face material (leading to varying error in the machine heading), and the miner's cutting cycle. It simulates control of the miner in three axes. Use of the simulator makes it possible to anticipate problems arising from the complex character of underground mining, which include unpredictable multi-pass coupling and unpredictable variation in geological conditions.

Jan 1, 1993