Search Documents

Soil erosion is strongly related to soil hydraulic properties. Understanding how surface coal mining impacts those properties is important in developing effective management practices to control erosion during reclamation. Soils from undisturbed areas, roughly graded mine spoil, replaced topsoil before seeding, and revegetated areas at the Rosebud Mine in Eastern Montana were evaluated to determine impacts on soil hydraulic properties. Field and laboratory studies were conducted to determine soil hydraulic properties, including particle-size distribution, organic matter content, and saturated hydraulic conductivity. WEPP simulations and risk analyses were performed on the soil hydraulic property data to determine the impacts of changes on soil erosion. The hydraulic properties of the soils in each representative area have significant differences due to the mining and reclamation practices at the mine. WEPP simulations show that the potential for soil erosion increases due to mining activities disturbing the soil. WEPP simulations also indicate that the potential for erosion may return to pre-mining levels over time with effective revegetation practices.

Feb 27, 2013

By S. C. Chelgani

The Thor lake deposit is a world class resource of rare earth (REE) metals and minerals in Canada. Development work to optimize a REE mineral recovery process flow sheet is underway, however, given the ore mineralogy; the developed reagent scheme is relatively complex. As part of a research project, micro flotation tests were conducted on a feed sample in order to examine factors affecting stream partitioning. SEM-EDX was performed to evaluate variability in grain composition between streams (concentrate and tails) and TOF-SIMS surface analysis was used to determine statistically significant differences in surface species particularly related to potential activation (or depression) of the examined mineral phases. SEM-EDX analysis reveal that the concentrate has a significantly higher proportion of REE bearing grains (carbonates and phosphates) relative to the tail (almost none were identified). Spectral fingerprinting by TOF-SIMS has allowed for the identification of all reagent species investigated. Reagent signal intensity discrimination on test stream mineral surfaces was observed by the TOF-SIMS analysis using reagents at plant concentration levels. TOF-SIMS analysis confirmed that REE bearing grains reporting to the concentrate are doing so in response to collector attachment whereas grains reporting to the tail are doing so in response to a lack of collector and/or in combination with the presence of the depressant. The surface analysis of gangue phases reveal a similar reagent discrimination; the signal intensity of collector species was significantly higher on the concentrate samples relative to the tails while depressant species were significantly enriched on the surface of the gangue phases in the tail samples. A detailed evaluation of the surface species representing the various reagents used in flotation scheme revealed a distinct competitive relationship between two of the reagents. The surface analysis identified that when used in concurrently, there appears to be a negative feedback resulting in a significant reduction in loading for several of the collectors on grains reporting to the concentrate. An evaluation of the effect of reagents on REE mineral in pilot plant is currently under way. Key words: Rare earth minerals, Flotation, Surface chemistry, TOF-SIMS, SEM-EDX

Feb 27, 2013

The molecular structures of isobutyl xanthate (IBX), diisobutyl dithiophosphate (DIBDTP), O-isobutyl-N-ethyl thionocarbamate (IBETC), O-isobutyl-N-ethylcarbonyl thionocarbamate (IBECTC) and O-isobutyl-N-ethylcarbonyl thiourea (IBECTU) were fully optimized using density functional theory (DFT) at the B3LYP/6-31+G(d,p) level with the integral equation formalism for the polarizable continuum model (IEF-PCM) in the aqueous phases. The effects of the polar groups in these thiol molecules on their collecting performances were determined by the energies and compositions of frontier molecular orbitals and the atomic charge values. Our results indicate that the sulfur atom(s) in IBX, DIBDTP, IBETC, IBECTC, or IBECTU molecule is the centre of reactivity. And the collecting abilities of these reagents for copper sulfide minerals follow the order as: IBX > IBECTU ? DIBDTP ? IBECTC > IBETC, and the order of their selectivities against pyrite is suggested as: IBX < DIBDTP < IBETC < IBECTU < IBECTC. The theoretical analysis provides an insight into the collecting powers of these collectors, and offers an atomic scale approach to understand the experimental data available in the literature. Keywords:xanthate; dithiophosphinate; thionocarbamate; thiourea; density functional theory; structure-activity relationship; copper sulfide mineral

Feb 27, 2013

By M. Leslar

Slope monitoring has been an important issue in static terrestrial lidar for some time. Several solutions for monitoring the progress of a slide have been devised over the years. All of these solutions have required users to be in the field operating the lidar equipment. This paper presents a new system developed using the Optech ILRIS-HD or ILRIS-LR lidar and the scripting language of PolyWorks to produce an autonomous slope monitoring system. This system has proven invaluable in detecting and alerting mine workers to potential danger within their mine sites. It has already been deployed in two mine sites and is scheduled to be installed at a third.

Feb 27, 2013

By P. Tong-jiang

We studied mineralogical characteristics of the vermiculite samples from seven mines in China. We found three types of interstratified structures in the investigated samples: 1:1 regular interstratified structure, segregated interstratified structure, and random interstratified structure. The vermiculite samples from six mines are mainly composed of phlogopite?vermiculite interstratified minerals, and the samples from the other mine are composed of chlorite?vermiculite interstratified mineral. The samples with phlogopite?vermiculite structure have high contents of K2O, TiO2 and Na2O. The samples with chlorite?vermiculite structure have the highest contents of MgO and Al2O3. The cation exchange capacity of the samples is 17.3?99.0 mmol/100g.The exchangeable cations of phlogopite?vermiculite samples from Weili Mine mainly include Na+ and Ca2+, while those of phlogopite?vermiculite samples from Tongguan Mine mainly include Mg2+ and Ca2+. The thermal expansion ratio of the samples is between 9 and 32. The exfoliated vermiculite products from Weili Mine have the best mechanical strength.

Feb 27, 2013

By L. B. Hales

Image analysis for feed belts and flotation has been used for over 20 years. It has been shown to aid in the modelling and optimization of Sag Mill circuits, and any improvements in the image analysis result in improvements in the model for control. Using a laser to measure the height-profile of rocks on the conveyor has been shown to increase the accuracy of the size classification. We have developed a system using two cameras in a stereoscopic configuration to provide height-profile measurement without the added expense and safety concerns of using a laser. Additionally, we have developed a novel technique for calibration of the system, using artificial intelligence techniques to optimize the model fit by adjusting the image analysis tuning parameters to values resulting in the best classification.

Feb 27, 2013

By J. A. Botín

In modern mining, the core of mine planning and design is the block model, a simplified representation wherein the ore deposit is divided in a number of virtual rock cubes, each characterized by technical and economics parameters. Mining engineers use this model to design the mine and develop production schedules. Traditionally, sustainability issues are not considered in the mine design, planning and engineering processes but rather are incorporated in the later stages of the feasibility evaluation as necessary expenditures and operating costs. This paper describes the results of a research project aiming to develop a methodology to incorporate sustainability parameters directly into the block model, so that they become an integral part of the design, planning and scheduling processes. It is considered that the incorporation of sustainable parameters into the block model would yield a more responsible mine design and improve mining projects sustainability performance

Feb 27, 2013

By J. M. Wempen

Booster fans, large underground fans, can increase the volumetric efficiency of ventilation systems by helping to balance the pressure and quantity distribution throughout a mine, reducing leakage and reducing the total power requirement. However, in ventilation systems that use booster fans there is a potential for system recirculation, the leakage of return air to intake air, and also for localized recirculation near the fan through the bulkhead and airlock doors. Air that is recirculated locally decreases the system efficiency because the quantity of air flow through the fan increases without increasing the airflow throughout the system. To understand the detailed flow characteristics of a ventilation system with a booster fan, two-dimensional computational fluid dynamics (CFD) models were developed using the software Ansys-FLUENT. Though two-dimensional models do not represent the full complexity of the flow dynamics, they do provide a good representation of the flow characteristics and they allow for a qualitative analysis of how the flow dynamics are affected by the system characteristics. The CFD models were used to evaluate how the number of booster fans, the booster fan placement, the location and geometry of the fan installation and the construction of the airlock system affect the flow characteristics and the localized efficiency of the ventilation system.

Feb 27, 2013

By A. Eccles

Phase designs are the foundation upon which all open pit mine sequence optimizations and budgets should be built. Unfortunately, at times, mine engineers skip the step of developing realistic pit phase designs - designs that include access ramps and mineable widths. Without mineable phase designs, their optimized schedules are based on theoretical pit shells or ?quick-and-dirty? plans with no ramps. The output from such optimizations is almost always overly optimistic. Without mineable designs, the production estimates are misleading, because they overestimate ore, and underestimate waste stripping requirements. Worse yet, when plans are not based on realistic phase designs, they can point to exactly the wrong decision in feasibility studies (i.e. ?go? when it should be ?no-go?). This paper discusses the importance and features of good pit phase design, and demonstrates the pitfalls of relying on optimized production sequences that are not based on properly designed pit phases.

Feb 27, 2013

By W. H. Dickinson

The performance of seven antiscalants spanning a range of chemistries was evaluated for control of calcium carbonate (CaCO3) formation in gold processing applications. Three preferred chemistries were identified which provided up to 100 percent inhibition in static jar tests when applied at 30 ppm dosage. The three products were further evaluated using a model carbon extraction circuit developed for this application. The test circuit enabled direct measurement of calcium carbonate formed on the carbon from a supersaturated solution under dynamic conditions. The antiscalants lowered CaCO3 buildup on the columns by 15 - 26 percent compared to untreated controls. Impact of the antiscalants on the rate and extent of gold loading onto a carbon adsorbent was evaluated in laboratory carbon-in-pulp (CIP) studies. The antiscalants generated a 25 - 35% increase in gold loading at gold extraction efficiencies up to 65%. On-site testing at a gold processing facility demonstrated that 10 ppm of the preferred antiscalant was able to fully suppressCaCO3formation in thickener overflow water.

Feb 27, 2013

By J. D. Bittner

The ST separator utilizes electrical charge differences between materials produced by surface contact or triboelectric charging. When two materials are in contact, material with a higher affinity for electrons gains electrons and thus charges negative, while material with lower electron affinity charges positive. This contact exchange of charge is universally observed for all materials, at times causing electrostatic nuisances that are a problem in some industries. Electron affinity is dependent on the chemical composition of the particle surface and will result in substantial differential charging of materials in a mixture of discrete particles of different composition. In the ST separator (Figures 1 and 2), material is fed into the thin gap 0.9 ? 1.5 cm (0.35 -0.6 in.) between two parallel planar electrodes. The particles are triboelectrically charged by inter-particle contact. For example, in the case of coal combustion fly ash, a mixture of carbon particles and mineral particles, the positively charged carbon and the negatively charged mineral are attracted to opposite electrodes. The particles are then swept up by a continuous moving open-mesh belt and conveyed in opposite directions. The belt moves the particles adjacent to each electrode toward opposite ends of the separator. The electric field need only move the particles a tiny fraction of a centimeter to move a particle from a left-moving to a right-moving stream. The counter current flow of the separating particles and continual triboelectric charging by carbon-mineral collisions provides for a multi-stage separation and results in excellent purity and recovery in a single-pass unit. The high belt speed also enables very high throughputs, up to 40 tonnes per hour on a single separator. By controlling various process parameters, such as belt speed, feed point, electrode gap and feed rate, the ST process produces low carbon fly ash at carbon contents of 2 % ± 0.5% from feed fly ashes ranging in carbon from 4% to over 30%.

Feb 27, 2013

By J. A. Organiscak

Water spray applications are one of the principal means of controlling airborne respirable dust in coal mines. Since many coals are hydrophobic and not easily wetted by water, wetting agents can be added to the spray water in an effort to improve coal wetting and assist with dust capture. In order to study wetting agent effects on coal dust capture, laboratory experiments were conducted with three wetting agents used by the coal industry on -325 mesh sized Pocahontas No. 3 coal dust. Significant differences in coal dust sinktimes were observed among the three wetting agents at water mixture concentrations of 0.05%, 0.1%, and 0.2%. The best wetting agent as identified by the coal dust sink test was only tested at the lowest 0.05% water mixture concentration and was found to have a negligible effect on spray airborne dust capture. Water spray airborne dust capture results for all three wetting agents tested at a 0.2% water mixture concentration showed that all three wetting agents exhibit similar but small improvements in dust capture efficiency as compared with water. These results indicate that the coal dust sink test may not be a good predictor for the capture of airborne dust. Additional research is needed to examine if the coal dust sink test is a better predictor of wetting agent dust suppression effects during cutting, loading, conveying, and dumping of coal products by comparison to airborne dust capture from sprays.

Feb 27, 2013

By M. A. Oskouei

Draglines are the main energy consumers in strip mines. Given the growing cost of energy and environmental concerns, it is important to properly understand dragline energy efficiency. The goal of current research at Missouri University of Science & Technology is to account for operator practice and operating conditions in modeling dragline energy efficiency. This paper presents preliminary correlation analysis and a framework for stochastic modeling of dragline energy efficiency. Thirteen operating parameters (including cycle times, payload, swing angle, and height of dump pile), operator working schedules, operating conditions, and drag, hoist, and swing energies were monitored for an 85 yd3 dragline. Operator effects were examined by two-sample t-tests. The relation between the parameters and energy consumption were assessed by correlation analysis and a stochastic modeling framework has been proposed for dragline energy efficiency. The results show that operator effects are significant (p< 0.05) and energy efficiency is correlated with operating parameters. The completed model will help the coal mines better predict energy consumption, with uncertainty, for different operating conditions.

Feb 27, 2013

Mine planners must select a single pit for design with the knowledge that the grades on which this selection is made are uncertain. This uncertainty is often ignored through the use of deterministic models of grade. This makes the mine planner?s job simpler but does not necessarily lead to the ?correct? or ?best? selection. Grade uncertainty is typically modelled with conditional simulation which generates multiple possible realisations of grade that are equally probable (or improbable) to occur. Methods for incorporating grade uncertainty into mine planning to date have either been perceived as being too complicated, not accessible or too time consuming. This paper proposes a simple and efficient modelling approach to incorporating conditional simulation into pit optimisation, which would be able to be applied in currently commercially software. An example for Resolute Mining Ltd?s Syama Gold Project in Mali shows the range of ore, grade and value outcomes associated with generating pits through a variety of methods.

Feb 27, 2013

Roof falls in coal mines typically occur in or around intersections and this has not changed in the last two decades. This research develops an improved scientific understanding of stress distribution and associated failure behavior around 4-way and 3-way coal mine intersections. Three-dimensional numerical analyses were performed to determine factors that influence intersection stability. The analyses used Hoek-Brown failure criterion. Failure zones around 3-way and 4-way intersections were developed. Intersection span and horizontal stress have a major influence on intersection stability. For the 4-way intersection, pillar corners across the intersection fail first and lead to progressive failure of immediate roof and floor layers. The mechanism of failure is similar for the 3-way entry but the shape and extension of failed zones differ. Coal ribs mostly fail due to tensile stress, while roof and floor strata fail due to shear stresses. Rib corners fail due to a combination of shear and tensile stresses. In addition to stress distribution; safety factor contours analysis was performed to assess stability of intersections.

Feb 27, 2013

By K. Oraee

Proven and probable coal reserves in Iran are estimated to be in excess of 5 Billion tons while the annual coal production is a mere 2 Million tons. Underdevelopment of the industry has proved higher production levels to be impossible, despite growing demand for energy supplies. The existences of numerous legislation are thought to have a detrimental effect on coal mining activities to the extent that some business entities have become uneconomical in many areas. This paper provides an analysis of the prevailing mining laws, policy making, legal frameworks and obstacles. It also outlines some other obstacles enshrined in the law and also highlights areas where foreign direct investment should be encouraged. The costs of lost opportunities are then estimated. The paper concludes by demonstrating that deregulations, amendments and in some cases complete abolishment of the incumbent legislations governing the coal mining industry will greatly enhance development of the industry. The analysis provided in this paper together with the results obtained, can prove useful to macro-economic policy makers both at local and national levels.

Feb 27, 2013

By N. Aouad

Dump truck operators are exposed to whole-body vibration (WBV) levels that exceed the International Standard Organization (ISO) 2631-1. The WBV level measured by RMS acceleration value, for operator comfort, and long-term health and safety is under 0.315 m/s2 by these standards. However, fundamental research by Frimpong and Aouad (2009, 2012) and field experimental study by Kumar (1999) have shown that operators are exposed to extreme WBV levels exposing them to injuries and musculoskeletal diseases in the long-term. These extreme WBV values in the vertical direction are equal to 3.56 m/s2, 1.12 m/s2 and 0.87 m/s2 for the operator?s seat, lower-back and cervical regions, respectively. This paper will outline current research to solve these problems. Keywords: WBV, Truck Vibrations, MSC.ADAMS, Virtual Prototyping

Feb 27, 2013

The Forestry Reclamation Approach (FRA) specifies that the upper 1.22 m of material on the reclaimed surface should be left as uncompacted as possible to facilitate tree root growth. One of the main concerns about applying the FRA to steep slopes is that the upper 1.22 m of material could cause the reclaimed slopes to be unstable. Successful application of FRA on flat and rolling surfaces precipitated this investigation. Details of a field investigation conducted at a steep-slope mine are available in an earlier publication (Kumar and Sweigard, 2011). A total of 70 survey monuments were driven into the slope in a regular pattern to monitor slope movement. Quarterly surveys of the monuments were done to quantify any type of mass movement either horizontally or vertically. The methodology proposed for slope movement was verified using numerical models. Analytical models based on limit equilibrium technique and numerical models based on the finite element method were developed for slope stability analysis. The limit equilibrium analysis was done using Geo-Slope software following the Simplified Bishop Method. The finite element (FEM) numerical model was developed using the Plaxis computer program following the strength reduction technique. Two kinds of slope stability analysis were performed: first with the top 1.22 m of loose material and second without top loose material. Finally, the field investigation results were compared with stability analysis results. Both of these approaches showed that application of the FRA on steep slopes is not causing any significant instability problems that would not exist otherwise for overly steepened slopes. Keywords: Forestry reclamation approach, steep slope, slope movement, factor of safety

Feb 27, 2013

By J. S. Meyer

Although salmonid fishes (including Pacific salmon and trout) have only intermediate sensitivity to copper (Cu) for traditional toxicity endpoints (survival, growth, and reproduction) and thus do not ?drive? the freshwater Cu criteria (e.g., see species-sensitivity ranking in US EPA 2007), Cu concentrations as low as 1 to 2 µg/L have been reported to impair olfaction (the sense of smell) in salmonids in laboratory experiments using dilute fresh water (see references in Meyer and Adams 2010 and DeForest et al. 2011). Olfaction is crucial to predator avoidance, recognition of kin, and reproductive synchronization (Baldwin et al. 2003); and Cu is of general ecotoxicological concern because it can be present in acid/mine rock drainage, industrial and municipal effluents, agricultural runoff, and urban stormwater runoff (Meyer et al. 2007). Therefore, there is public concern that the current regulation of Cu in surface waters is not stringent enough to protect salmonid fishes against olfactory impairment (e.g., OSU 2007; Pearson 2007). Because the toxicity of metals to aquatic organisms is a function of water chemistry [e.g., acute toxicity of Cu generally decreases as pH, water hardness (Ca2+ + Mg2+), alkalinity, and dissolved organic carbon (DOC) concentrations increase; Meyer et al. 2007], hardness-based freshwater criteria for metals are lower at lower water hardness. The recently-developed biotic ligand model (BLM) explicitly takes into account all four of those water chemistry parameters and the concentrations of other major inorganic cations (Na+, K+) and anions (Cl-, SO42-) to predict the acute toxicity of cationic metals (e.g., Ag, Cd, Cu, Ni, Pb, Zn) to aquatic organisms; and the BLM has been adopted by the U.S. Environmental Protection Agency (US EPA) to calculate acute and chronic national freshwater criteria for Cu (US EPA 2007). Consistent with observations of Cu toxicity to aquatic organisms, BLM-based Cu criteria generally are lower at lower pH, water hardness, alkalinity, and DOC concentrations. Therefore, although threshold concentrations for olfactory impairment by Cu can be low in dilute fresh waters, the corresponding hardness-based and BLM-based Cu criteria for the same waters also tend to be low. This leads to a logical question: Are Cu criteria already protective against impairment of olfaction in salmonid fishes, thus obviating the need to decrease those criteria even lower to protect against adverse effects to this physiological/ecotoxicological endpoint? Herein, we demonstrate that in all studies conducted to date, the US EPA?s BLM-based freshwater Cu criteria would have been protective against olfactory impairment in salmonid fishes, but the US EPA?s hardness-based criteria would not always have been protective. This distinction is important because all 50 States in the USA still use hardness-based Cu criteria in their water quality standards, and only some of the States allow use of the BLM to calculate site-specific Cu criteria. Additionally, in the absence of empirical results for calibration of a saltwater Cu-olfactory model, we demonstrate that a proposed unified freshwater-saltwater Cu-olfactory BLM predicts the US EPA?s current saltwater Cu criteria would be protective against olfactory impairment caused by Cu in sea water.

Feb 27, 2013

By D. J. Carpenter

Safe and successful mine closure represents a fundamental work element that needs to accommodate the geochemical conditions existing at the completion of the mining and ore processing effort. Given the interests in limiting costs and time associated with mine closure efforts enhanced prior understanding of the geochemical conditions likely to exist upon exhaustion of the economic reserves can provide important benefits. The purpose of this paper is to document the benefits associated with geochemical modeling and understanding how the ore formation process may impact mine closure efforts, using one ore deposit type as an example. Specifically, this paper will emphasize the geochemical processes leading to the formation of sandstone-hosted uranium roll-type deposits and how the resultant concentrations and distributions of ore and gangue phases need to be incorporated into understanding the geochemical conditions projected to exist at the end of mineral recovery efforts. The paper will describe the evolution of geochemical conditions leading to ore body formation and the geochemical effects induced by open pit mining and how these may be used to understand both the geochemical controls and constraints on residual mine water. In addition, a discussion will be provided on how these conditions may be simulated by solution equilibria and kinetic modeling to develop optimum approaches to achieve applicable closure standards. This paper will also discuss specific augmentations to existing industry standard solution equilibria and kinetic models and associated thermodynamic databases to maximize the predictive accuracy of the geochemical modeling results. The benefits of understanding the electrochemically reactive behavior of uranium and associated gangue phases and incorporating this behavior into mine closure efforts will be presented. The culmination of the benefits of the geochemical modeling will ultimately be the development of a sustainable approach to uranium mine closure that is based upon an engineered environment designed to return the ore body to stable geochemical conditions.

Feb 27, 2013