Search Documents

By Kevin Phelps, Jason Baird, Philip Mulligan, Dominique Nolan

Determining the transitions from run-up to optimal cut length and optimal cut length to run down, without bias, from the penetration of a linear shaped charge (LSC) is difficult. The stresses applied to the targets during explosive testing can distort the targets in such a manner that determining the true distance of cut, penetration, or fracture can be demanding. Through the course of this research, it was observed that the researchers made many of the errors involved in the collection of data. Among these errors researchers found problems in: determining and fitting the sample to a single plane from which to read measurements, determining where along the path of cut the three phases of penetration transition, and the precision of measurement based on handheld tools and the human eye. This study looks at three methods of recording the data of a series of linear shaped charge tests. The tests resulted in samples which are not ideal for measuring with common laboratory devices like measuring tapes, calipers, or rulers. The first method utilized these common laboratory devices and the difficulties the authors experienced are described in this paper. The second and third methods involve digital photography, image manipulation, and the use of AutoCAD. Methods two and three are then compared to the simple observational method and discussion is made in regards to the precision and accuracy of each method.

Jan 1, 2013

By Richard H. De Voto

The Pb-Zn-Ag deposits within the Lower and Middle Paleozoic strata of central Colorado (Leadville, Gilman, Aspen, and others) occur principally in Late Mississippian karst-solution features within dolomites and, to a lesser extent, limestones. Several un- conformities within the Devonian and Mississippian carbonate rocks and the subregional dolomitization of the Leadville (Mississippian) Formation that occurred during the Late Mississippian resulted from recurrent uplift of elements of the Ancestral Sawatch, Gore, and Front Range areas within central Colorado. Uplift of these areas also strongly influenced the details of the extensive karst topography that developed during the Late Mississippian. In particular, uplift of the Sawatch Range area caused paleovalleys from 300-600 ft deep to form on the karst landscape. The pattern of karst-solution caverns, sinkholes, cutters, channelways, and breccia-rubble zones was strongly controlled by incision of surface drainages and the strong northeast-trending Mississippian joint system. These subterranean karst-solution features and breccia-rubble soil [ ] zones are the primary controls of the location of the Pb-Zn-Ag ore deposits in these rocks. In the Leadville and Aspen districts, the deeply incised paleovalleys occur immediately adjacent to the principal areas of mineralization. Pennsylvanian deposition of a thick terrigenous and evaporite sequence occurred within central Colorado in response to actively subsiding extensional basins and adjacent high-relief uplift areas. Hot brines developed within the Pennsylvanian strata, migrated laterally to, and moved upward vertically along, basin- margin faults during continued Pennsylvanian subsidence and deposition. These metal-rich brines migrated into karst-solution features within the Lower and Middle Paleozoic dolomites and limestones, principally within the Leadville Formation, in basin- edge uplifted locales where the Pb-Zn-Ag minerals were precipitated. Field relationships, mineral assemblages and paragenesis, fluid-inclusion data, and isotope studies suggest that the metals and brines were derived within the Pennsylvanian sedimentary sequence and that the ore minerals were deposited under different temperatures and at different depths from deposit to deposit. Chemical reaction with the carbonate cave sediment and wallrock, cooling of fluid temperatures, and mixing with meteoric ground waters were the probable combined causes of mineral deposition in the karst-solution features. Late Cretaceous-Tertiary intrusive activity has subsequently modified some of the primary Pb-Zn-Ag deposits in local areas.

Jan 1, 2013

By Willie M. NeSmith, W. Morgan NeSmith, Alan Roach

"In 2013, Augered Cast-in-Place (ACIP) piles are a mature foundation technology throughout the United States. General guidelines for the design and construction of ACIP piles are available along with numerous references for design in specific North American geologies. In fact, the current generation of contractors and geotechnical practitioners might view ACIP piles as just another deep foundation option to be considered, along with driven piles, drilled shafts and others. This acceptance has developed, however, over a 60-plus year period.The term, Augered Pressure-Grouted (APG) pile is often used when referring to ACIP piles because the piles emerged out of construction processes at the Intrusion-Prepakt firm in the late 1940s. The company’s specialty was pressure grouting and preplaced aggregate concrete. The grouting was typically accomplished by driving a pipe to a target level and then injecting grout under pressure. In some soil conditions, it was necessary to use an auger to reach the desired grouting depth. In these circumstances, the grout pipe was driven beside the auger and grout was pumped as the auger was withdrawn. The grout pipe was then withdrawn as well. This was the genesis of the APG, or ACIP pile, and many piles were installed using this technique. The patent application, “Method for Forming Piles” was filed by Raymond Patterson of Intrusion-Prepakt in 1951, and the patent was granted in 1956. The process was eventually modified when a suitable hollow-stem auger was developed. Licenses were granted to the Lee Turzillo Contracting Company and Berkel & Company Contractors, Inc. in the late 1950s. Each of the three companies Patent, LicensesThe patent application, “Method for Forming Piles” was filed by Raymond Patterson of Intrusion-Prepakt in 1951, and the patent was granted in 1956. The process was eventually modified when a suitable hollow-stem auger was developed. Licenses were granted to the Lee Turzillo Contracting Company and Berkel & Company Contractors, Inc. in the late 1950s. Each of the three companies coined their own terms for the piling process: “Pakt-In-Place” for Intrusion-Prepakt, “Auger Pressure-Grouted” for Berkel and “Augercast” for Turzillo. Over time, “Augercast” was frequently used as a generic term for the system. The installation of these piles was, and still is, a highly nuanced process; “contractor dependent” is a term often seen today. Intrusion-Prepakt, Berkel and Turzillo all had personnel who were part of the original group that developed the system and who appreciated the craftsmanship involved in forming sound piles."

Jan 1, 2013

By Shu Xinqian, Zhou Weining, Shan Zhiqiang, Feng Jifu

"Modified calcination conditions on the extraction of rubidium resources from muscovite (KAlz[AlSi301o](OH)2) ore are systematically studied. The impact of various factors on the rubidium leaching rate is also analyzed, including the agent types, roasting time, the mass ratio, roasting temperature, etc. The results indicate that the best agent is a combination of sodium chloride and calcium chloride, its mass ratio ofmuscovite/NaCl/CaClz is 1:0.25:0.25. Calcined at 8500 for 30 minutes, the rubidium leaching rate is up to 90%. The reaction of muscovite ore with the chlorinating agent CaC12 has been studied by TG/DSC, the calcined intermediates are identified by XRD, and the surface morphology before and after leaching is characterized by SEM. Rubidium chloride products can be obtained with a purity of 92% by using t-BAMBP extraction, hydrochloric acid reextraction and purification.IntroductionRubidium is one ofrare alkali metals, which is found in 1981 by German R.W. Bunsen and G.R. Kirchhof. Rubidium includes the following features: atomic number is 37, each atom weight 85, the body-centred cubic lattice, each unit cell has two metal atoms, and the density is 1.532g/cm3. The properties of low melting point (312.46 K) and malleability make rubidium have a strong chemical activity and photoemission. Rubidium provides a main material for manufacturing phototube with a wide range oflight waves, which possess high sensitivity and stability. Efforts are being made to carry out research on rubidium ion gngine, magnetic flux generators and thermoelectric transudcer, etc. Rubidium exists in muscovite ore(KA12[AlSh01o](OH)2 (monoclinic system and hexagonal layered structure) as isomorphism and replace the large radius of the potassium atoms, as well as part of rubidium locate between structure layers. The complex components bring great difficulty in comprehensive recycling."

Jan 1, 2013

By R. Bashir, J. F. Hatley

ABSTRACT Northern Saskatchewan boasts some of the world’s largest known high-grade uranium deposits. The successful mining of these deposits cannot be accomplished without overcoming technical challenges, however, which include high grade of the uranium ore, specialized mining methods to deal with groundwater at high pressures, and poor ground conditions. This paper discusses the various mechanisms of inflows at three of Cameco Corporation’s sites in northern Saskatchewan. The risk of inflows is quantified in terms of unique challenges due to hydrogeological conditions, rock mass integrity, and uncertainty in geological conditions. Strategies in the case of an inflow are also briefly described.

Jan 1, 2013

By Xinhua Wang, Xuefeng Liu, Die Yang, Lifeng Zhang, Wen Yang

"CSP thin slab continuous casters are well used in recent years. The control of heat transfer in the mold is very important because it is correlated with several slab defects. The mean heat flux of CSP mold was studied based on the plant production data of LCAK steel and weathering steel. The effect of various operation conditions on the heat flux was analyzed and discussed. The results showed that the heat flux was 2.1-2.6 MW/m2 on the wide face and 1.2-2.2 MW/m2 on the narrow face for the casting of LCAK steels. During the casting of weathering steel, the heat flus was mostly 2.05-2.5 MW/m2 on the wide face and was 1.1-1.8 MW/m2 on the narrow face. The heat flux depended largely on the casting speed. The heat flux on the wide face increased obviously with increasing casting speed when the casting speed was relatively low; however, at high speed, the heat flux increased slowly or kept constant. At low casting speed, the heat flux depended little on the superheat of the molten steel. The mean heat flux depended little on the level fluctuation at continuous casting mold.IntroductionCSP thin slab continuous casters are used more frequently in recent years for its low cost of construction and manufacturing. The structure of CSP mold is very different from that of conventional thick slab casting mold, inducing the difference of heat flux between them. There have been some studies about the heat flux of thick and medium slab casters [l, 2]. Heat transfer in the mold is very important for the solidification of molten steel because it is correlated with several slab defects such as slab break-out, longitudinal crack, and surface depression. Moreover, higher casting speed is desired to improve the productivity. The control of solidified shell is extremely important. The heat flux is largely influenced by several casting parameters such as the cooling intensity of the mold, the casting speed[3], the mold flux powder [3, 4] and the carbon content of steel as well [5]. The investigation on the heat flux and affecting parameters can help to understand the solidification of molten steel in the mold."

Jan 1, 2013

By John MacDonald

An unstable economy has shown businesses what the mining industry has known for decades ? a successful business location today may not succeed in the future. Unexpected expenses, natural events and workforce changes have a big impact on the costs of production. To help focus production and maintenance budgets, mining executives are increasingly turning to production metrics to make key decisions. Role of mine and mill data Companies employ a variety of information systems to allow employees to accomplish their operational tasks, and each worker is focused on the metrics, or key performance indicators (KPI), for his or her individual function. For example, machine operators monitor throughput and cycle time to keep the machines running continuously and to meet daily production quotas. Meanwhile, the maintenance teams monitor machine performance, overall equipment effectiveness (OEE) and meantime between failure to predict and help prevent downtime.

Jan 1, 2013

By G. Castillo, G. Thies, C. Bissue

"Newmont’s Phoenix mine began gold production in 2006 and has since experienced difficulties in reaching design throughput due to variability in ore hardness. In 2010, a debottlenecking study was conducted, generating multiple options to increase throughput of the existing Phoenix Mill through a series of phased expansions. An option was selected in early 2011 to increase the current concentrator capacity by approximately 25% through two phases. The first phase of the project was the installation of a secondary crushing and screening circuit in order to reduce SAG feed size from a P80 of 6 inches to 2 inches. The second phase focuses on downstream unit operations in the concentrator aiming to relieve existing bottlenecks such as flotation. This paper analyzes the design, commissioning, and operation of a recently installed SAG Pre-crush circuit (Phase 1). The design discussion will focus on concept development, flowsheet design, design criteria, process models, design limitations, and control philosophy. Discussion on the integration of operating data and flowsheet into design during engineering will be presented. Actual operating data of major equipment is gathered from the commissioning and operation of the circuit and compared to the initial design models. Conclusions will be drawn on equipment design factors used during engineering, and the success of model integration into operation. The paper concludes on the successes of the project and where improvements can be made during design.INTRODUCTIONThe Phoenix mine is located within 25 miles of the town of Battle Mountain, Nevada. The mill processes copper, silver, and gold ore. Production started in 2006 and has since struggled to reach the designed tonnage of 33,600 stpd due to the variability in ore hardness. In production year 2010-2011, the Phoenix mill average daily throughput of 33,000 stpd. In 2008, a larger primary crusher (FLS 60/89 gyratory crusher) was installed to operate in parallel with the originally supplied primary crusher (Metso 50/65 gyratory crusher), in order to provide additional capacity upfront in the circuit so that the primary crushing circuit could keep up with the mill.In 2010, a mill debottlenecking study was completed to assess the various options that could be implemented to increase the current mill capacity. The study was completed in late 2010 and contained four tonnages that Phoenix could achieve through various expansion scenarios. A single option was selected in early 2011 to increase the mill capacity from 33,000 stpd to 48,000 stpd. The selected option looked at a four phased expansion that would increase the capacity of the Phoenix mill and address the mill’s current bottlenecks:"

Jan 1, 2013

"The Dumont deposit is a large (1066 Mt probable reserve) low grade (0.27% nickel), nickel sulphide project located in the Abitibi region 25km west of Amos, Quebec. Royal Nickel Corporation acquired the project in 2007 and has since taken the deposit through pre-feasibility. And updated, revised pre-feasibility was released in July 2012.The disseminated nickel sulphide and alloy mineralization is hosted within the serpentinized dunite subzone of the Dumont Sill; a differentiated, pervasively serpentinized, ultramafic sill of komatitic affinity. Pentlandite, heazlewoodite and awaruite are the dominant nickel-bearing, metallic phases and can be recovered by conventional methods (flotation, mag separation). Non-recoverable nickel is also present within the silicate matrix of the serpentinized dunite and is locked in serpentine (Fe and Mg-rich variants) and minor olivine.A detailed mineralogical program including 1097 QEMSCAN® samples and 4300 electron microprobe points were undertaken to increase the understanding of the nickel deportment in the various recoverable and non-recoverable phases in a spatial context across the deposit. Eighty-three (83) metallurgical tests performed under a standard procedure have linked the mineralogy to metallurgical performance. This has allowed the creation and modelling of geometallurgical domains on a block by block basis to understand the recovery variation and metallurgical performance throughout the deposit. Understanding the spatial variability of Ni deportment in recoverable and non-recoverable phases through mineralogy is the key to understanding metallurgical performance thus, unlocking the value of the Dumont deposit and other large tonnage low grade ultramafic nickel deposits."

Jan 1, 2013

By Zhang Libo, Peng Jinhui, Zhang Zhengfu, Fu Mengbi, Han Yamei

In this paper, results of a novel synthesis method of carbon-coated LiNi113Mn113Co11302 cathode material for lithium-ion battery are reported. The carbon coating was produced from a precursor, glucose, by microwave-pyrolysis method. The structure, morphology and electrochemical performance of the bare and carbon-coated LiNi113Mn113Co11302 were characterized by X-ray diffraction, scanning electron microscopy and charge-discharge tests respectively. The L8(27) orthogonal experiments were carried out to optimize LiNi113Co113Mn1130z/C technological conditions. The conditions of the orthogonal experiments were that the glucose content were 1.5 % and 4 %, the holding time were 15min and 30min, the heating temperature were 400 °C and 500 °C and the solvent were H20 and CH3CH20H. The main experiment target include specific capacity at 0.1C and 0.2C, Capacity retention rate, medium voltage attenuation rate and The fifth discharge medium voltage. The data were analyzed by Minitab 14 statistics software. The results of analysis of variance indicated that the most influential factor was the glucose content despite of discharge rate. Secondly, the effect of the solvent was equivalent to the holding time.

Jan 1, 2013

By Boyd R. Davis

Like many pyrometallurgy researchers, Ralph Harris? work extended over both light metals (lithium and magnesium) and base metals. His work looked at feed preparation, primary production, and secondary treatment. The thermodynamic principles of chemical metallurgy allowed Ralph to move between these two groups of metals. However, these metals have few similarities when projects are being developed. The traditional ?deposit-based? drivers for base metal operations do not apply to the same degree with light metals projects. While high purity, low cost feed is important to light metals projects, it should not be considered as the main reason for a smelter project. While it is clearly understood that technology (energy costs) is the driver for aluminum production, it is less considered for other light metals. This paper will look at the break down of base and light metals? production costs to try to quantify the balance between feed costs and technology for each metal group.

Jan 1, 2013

By Kam Ng

For bridges or buildings that may be subjected to large vertical and lateral loads, drilled shafts offer an economic foundation solution. While the current drilled shaft design practice is considered adequate, introducing a performance-based approach to designing the drilled shafts will make their design more cost-effective and produce more dependable response. This concept was examined using analysis of 41 drilled shaft load test data from several states. This process identified the challenge with the lack of information from the Osterberg (O-cell) load test method to characterize the full top load-displacement response. When a typical single O-cell is utilized in a drilled shaft test, depending on the location of the O-cell and the geomaterials present along and beneath the shaft, the load test result typically quantifies either the side resistance or end bearing reaching the ultimate load-displacement curve but not both components. This limitation hinders the determination of a suitable shaft resistance as a function of a target top displacement. To overcome this challenge, an improved procedure is proposed for establishing the full load-displacement curve based on data gathered from one O-cell. The method will be presented in the paper for three different cases (i.e., side resistance reaches the ultimate during the test, end bearing reaches the ultimate during the test, and neither components reach the ultimate values). Because it allows the characterization of the full load-displacement curve, the proposed procedure will allow performance-based design of drilled shafts with due consideration to settlement while satisfying the Load and Resistance Factor Design.

Jan 1, 2013

By T. J. Kolokoto

This paper is based on a project conducted at Khomanani 2 shaft, Anglo American Platinum Limited. The main objective was to find an alternative support element in stopes to address the falls of ground (FOG) problem experienced at this shaft. Literature review was the major method used in the investigations. Resin bolts or any 1.5 m in-stope roofbolts were considered. The shaft was making use of 0.9 m long friction bolts, and these could not prevent the FOG experienced. Observations indicated that the FOG resulted in fall-out thicknesses averaging to 1.1 m, which is greater than the supported length of the friction bolts. The implementation of 1.5 m long bolts was recommended as a result of the project. These bolts will be able to address the fall-out thickness and provide sufficient support resistance to mitigate FOG. The chosen support element will result in a relatively small increase in support costs.

Jan 1, 2013

By B. Sergeant

Any study of the contentious subject of nationalization can ultimately be reduced to a sombre analysis of the simultaneous, and very different, interests of capital, labour, and government. Each of these interests attempts to maximize its objectives, subject to checks and balances provided, in an ideal system, by a country's executive government, legislature, and judiciary. Where even one of the three interests goes out of control, the consequences can be disastrous. The case histories show that when this occurs, the most common culprit is government, or its proxy, such as a dictator. At the other extreme, the case studies indicate that the optimum outcome occurs when capital, labour, and government are 'ring fenced' from each other: each enjoys its rights, but is also subject to duties. 'Conflicts of interest' between the three entities are ideally avoided to the maximum possible extent. The case studies include several salient instances from both the DRC (Gécamines, La Générale des Carrières et des Mines) and Zambia, along with Ghana and Chile. Further instances are examined in South Africa (gold), India (Coal of India), Brazil (Petrobras), Venezuela (Petróleos de Venezuela), Sweden (Luossavaara-Kiirunavaara Aktiebolag), Mauritania (Société Nationale Industrielle et Minière), Norway (Norsk Hydro), Botswana (Debswana), and Namibia (Namdeb). The article concludes broadly that South Africa's minerals sector is not ready for nationalization.

Jan 1, 2013

By Alan D. Fisher

Amtrak made a decision to replace an aging bascule bridge with a vertical lift bridge for their crossing of the Thames River in New London, Connecticut. The new lift bridge occupies the same alignment and shares the same foundations as the bascule span. During construction the deep foundation caisson supporting the bascule span settled and tilted. Investigation into possible reasons revealed interesting historical facts, both of the construction of the innovative open well caisson foundations and of the state-of-the-art in tremie concrete placing methods in use at the turn of the century. This paper describes both of these topics.

Jan 1, 2013

By Kevin M. Ansdell, Irvine R. Annesley, Christine L. Mckechnie

The U-Th-REE mineralization at Fraser Lakes Zone B is hosted by granitic pegmatites and leucogranites, which lie along the deformed contact between Paleoproterozoic metasedimentary gneiss of the Wollaston Group and Archean orthogneiss, approximately 25 km from the southeastern edge of the Athabasca Basin. The pegmatites/leucogranites are subcordant to concordant with the regional foliation and are concentrated within a northeast-plunging antiformal fold nose, the study area, which lies west of Fraser Lakes. The mineralized pegmatites/leucogranites in the western part of the study area (Group A) are typically enriched in U (± Th) with Th/U ~1, and contain uraninite, thorite, zircon, and allanite. Those intruding the central part of the study area (Group B) are generally enriched in Th and LREE, with Th/U >2, and contain monazite, thorite (commonly U-enriched), and zircon. The pegmatites and leucogranites in Group A tend to be slightly enriched in SiO2 and depleted in TiO2 relative to those in Group B and are interpreted to represent more evolved crustal melts. Both groups are peraluminous and show varied chemistry. Partial melting (~850ºC and 9 kbar) of a metasedimentary rock-dominated source, entrainment of accessory minerals as xenocrysts, and assimilation-fractional crystallization processes combined to enrich the granitic pegmatites/leucogranites in U, Th, and REE elements. Transfer of melt from the source region to the crystallization sites was assisted by deformation within and along major structural zones, such as the folded Archean-Paleoproterozoic discontinuity. The character of mineralization and structural control in the study area is reminiscent of the alaskite-hosted deposits at Rössing, Namibia.

Jan 1, 2013

By Larry F. Drolet

Charleston, SC is anything but boring. The city was founded in 1670 and has played a significant role throughout the history of the United States. Located along the coast of the Atlantic Ocean in the southeastern United States, Charleston was a vital city in America?s early existence. Charleston?s coastal location has helped the city become the fourth largest cargo port in the United States and earn the 2011 designation as the number one travel destination in the United States by the Conde Nast Traveler Magazine. Part of Charleston?s charm and beauty can be attributed to its historic structures and churches that line nearly every sidewalk, roadways that were laid out based on the width of horse carriages, great weather, southern hospitality and coastal living. Now imagine the challenges of installing new, or re-placing aging infrastructure, in this setting. Every shovel full of dirt, every stick of pipe and every roadway sub-surface has its own historic story to tell. For engineering minded individuals, Charleston?s infrastructure has almost as fascinating a history as its more visible surface structures. Charleston was among one of the first American cities to construct separate sanitary and storm water drainage infrastructure. This concept has roots dating back to the city?s founding and is a credit to the foresight of its founding fathers who understood the basic health differences between sanitary and storm water.

Jan 1, 2013

By U. Gorkhan Akkaya, N. Enver

Geographic information system (GIS) is one of the most accurate and useful tools to help decision – making for decision-makers. As to expert systems, it provides solutions to the problems faced by mimicking reasoning of the human experts. Blasting operations in mining include high risks for the vicinity of the operations. GIS having required mechanisms to take right decisions for the people who have to make right and precise decisions, while it is utilized as a integrated system with expert reasoning, is thought to be considered important tool that provides to take decisions with ease, and also to reduce the risks in the blasting operations. It is possible to find out both of the economic and optimum solutions to solve the various encountered problems in the mining activities such as blasting operations, only when GIS integrated expert systems is used. Managing the spatial data unified with expert reasoning is the one of the greatest advantages of the system. In the scope of the study, various scientific studies were investigated. The benefits of the system were figured out and the phases of a unified system were proposed in the blasting operations.

Jan 1, 2013

By D. Govender

Theoretical flotation models suggest that there is a positive relationship between bubble-particle collision rates and turbulent kinetic energy dissipation. Fine particle flotation performance is generally enhanced by increased collision frequency and hence higher energy dissipation. Contrarily, increased turbulence in the rotor-stator region is related to higher detachment frequency of the coarser size range. Therefore, the optimal modes of recovery for the 'fine' and 'coarse' size classes appear to be diametrically opposed. Industrial applications have previously confirmed that applying greater power to flotation slurries yields significant improvements in fine particle recovery. However, recovery of the coarser size class favours a different flotation environment. An improvement in the flotation kinetics of the fine and coarse size classes, provided there is no adverse metallurgical influence on the intermediate size ranges, is obviously beneficial to the overall recovery response. Managing the local turbulent kinetic energy dissipation, and hence the power imparted to the slurry, offers the benefit of targeting the particle size ranges exhibiting slower kinetics. FLSmidth recently introduced the practical implementation of this concept. In principle, it decouples flotation regimes where fine and coarse particles exhibit preferentially recovery. In the case of naturally aspirated machines (Wemco®), it is referred to as Hybrid Energy Flotation? and incorporates at least three phases: > Standard flotation machines (standard energy input, rotor speed (r/min), rotor size/type) at the beginning of the row, where flotation is typically froth-phase limited and operational and set-up parameters have a limited influence on the recovery > Higher-powered flotation machines (high rotor speed, high-power rotor size/type) at the end of the row to improve fine particle recovery > Lower-powered flotation machines (low rotor speed, low power rotor size/type) to enhance coarse particle recovery. A CFD-based flotation model is used to highlight the effect of turbulent dissipation energy on attachment and detachment rates. Preferential collection zones for fine, and 'coarse' particles are predicted for both forced-air and naturally aspirated machines. The greater predominance of UG2 ore types, coupled with the skewed feed distribution of platinum group metals (PGMs) to the finer size fractions, suggests that PGM flotation circuits are not designed for optimal recovery across the size distribution. The application of the hybrid energy concept to PGM flotation offers a possible shift towards a more efficient flotation circuit solution through a managed distribution of energy.

Jan 1, 2013

By Xi-Shan Li, Qian Li, Yong-bin Yang, Li-na Cui, Tao Jiang, Jie Ge

"With regard to control environment pollution in the roasting pretreatment of sulfur & arsenic-bearing gold concentrate, roasting of double-layered pellet was proposed. In the paper, the characteristics of double-layered pellet roasting were studied. Removal and solidification rates of sulfur and arsenic were investigated as primary factors. The result indicated that the removal and solidification rates of arsenic reached up to 95.91 % and 98.95% while the sulfur was 97.19% and 97.90% respectively on the premise of adopting slaked lime as solidified agent at temperature of 6000, the package proportion of 2.14 and roasting time of 3h. However, pyrite and arsenopyrite were transformed to hematite and magnetite and product of solidification mainly consisted of calcium sulfate, calcium arsenate and calcium sulfite within optimum roasting parameters.IntroductionUtilization of refractory gold resources has been gradually concentrated on with the depletion of the gold resources which are easy to deal with in the world [1]. Sulfur and arsenic-bearing gold ore is a typical refractory gold one, in which ultrafme gold is encapsulated in the structure of metal sulfide minerals [2,3], so it gives poor recovery through direct cyanide leaching. These refractory ores need pretreatment before the process of cyanide leaching to undermine lattice structure of pyrite and arsenopyrite containing gold [4] so that the gold could touch with cyanide solution [5]. Among various methods of pretreatment, conventional roasting method is most effective, but this process generates gases such as S02 and As203 harmful to environment. Therefore solidification roasting was proposed to solve this problem occurring in the conventional roasting at the end of last century."

Jan 1, 2013