Search Documents

By G. van Aswegen

The geometry and morphology of a set of low-angle fractures around a stope in a deep Witwatersrand gold mine are explained in terms of extension fractures forming under variable conditions of stress. Primary extension fractures (E1) form some distance ahead of an advancing stope along the s1, s2 plane. With stope advance, a couple of these fractures end up in a stress regime conducive to transpressional shear and a secondary set of extension fractures(E2) is formed at a high angle to the primary fractures. i.e. at a low angle to the stope. As the E2 fractures are undermined, they migrate into a stress regime of transtensional shear and a third set of extension fractures (E3) may develop between E2 fractures. These have sigmoidal shapes, being parallel to the E2 fractures at the E2 discontinuity where s3 is negative, and curved through the un-fractured rock between E2 fractures where s3 is positive at the instant of fracturing. The fractures all display fractographic features characteristic of dynamic extension failure with striae indicative of the direction of rupture propagation and the local, instantaneous orientation of s1.

Jan 1, 2012

In general, it cannot be assumed that the strength of coal pillars remains constant over long periods of time. Field observations indicate that a coal seam, especially when it contains a parting layer, deteriorates over time, reducing the load-bearing capacity of the pillars. This paper discusses a unique approach to determining the time-dependent strength of coal pillars in the field. Three coal pillars that were developed 5, 15, and 50 years ago were chosen for the study. Holes were drilled in coal and parting layers in each pillar, and the strength profiles were determined for each hole using a borehole penetrometer. The strength data were treated statistically to establish time-dependent strength equations for different layers. The results can be used to help estimate the loss of pillar capacity over time.

Jan 1, 2012

By J. P. Downey, T. Salisbury, M. Berlin, E. Rosenberg, G. Pinson, R. Christianson, K. Gleason, W. Gleason, S. Davis

"Direct digital manufacturing offers promise as a technique for fabricating complex hydrogen purification membrane support structures. Free form fabrication methods can produce parts with complex structures, and sintering parameters can be controlled to adjust the density, pore structure, pore pathways and strength in catalytic substrate constructs. Efforts are underway to define the influence of selected process variables on the chemical and mechanical properties.IntroductionThe Center for Advanced Mineral and Metallurgical Processes (CAMP), in collaboration with the Metallurgical and Materials Engineering Department at Montana Tech and the Chemistry Department at the University of Montana, is engaged in the development of new methods and materials for hydrogen purification membrane production. Because hydrogen readily passes through palladium, a structurally sound palladium-based membrane is capable of separating relatively pure hydrogen from other gases. In order for this technology to succeed, a suitable substrate material must be identified.High purity hydrogen is produced by various means. A common method involves a two-stage process for separating hydrogen from a hydrocarbon gas stream: 1) hydrogen-rich syngas is produced by the catalytic reaction of natural gas or another light hydrocarbon gas with steam, and 2) hydrogen is separated from the other syngas components by pressure swing adsorption (PSA) (US. Energy Information Agency, 2011). In PSA, gases enter a column that is packed with a material that absorbs gases as the chamber is filled and pressurized. As the pressure is slowly relieved, the absorbent material releases hydrogen at a higher pressure than the impurity gases. PSA processes produce 99.99% pure hydrogen at a high recovery rate. These systems typically demand a high capital investment due to the high pressure and multiple stages (columns) needed to attain high hydrogen production rates.Research geared toward reducing hydrogen production cost is focused on the development of improved catalysts and adsorbent materials as well as more effective single-stage separation processes. An interesting method combines hydrogen reduction catalysis and filtration. Nascent hydrogen is separated from other gases as it selectively permeates the filter. Catalyst filters may be made of gold, silver, platinum, palladium or precious metal alloys (Davis, 2009)."

Jan 1, 2012

By Ben Burger

This paper describes the design, the first three years of operation and optimization of a large, single stage SAG mill at Minera Yanacocha?s Gold Mill facility located in northern Peru. The Gold Mill was commissioned in March 2008 with a 32? x 32? EGL, 16.5MW single stage SAG mill, to process 5 million tonnes per annum high grade oxide Au/Ag ore. Operational control, feed size distribution, grinding media, mill liner, grate and pulp lifter optimisation have allowed the mill to operate 15-30% above design throughput rates, but with a product P80 coarser than design. As part of the optimization, full grinding circuit surveys were conducted. Historical operating data and survey data were analyzed and used to evaluate possible circuit changes and determine alternative operating strategies. A number of changes were implemented which allowed the SAG mill to operate similarly to a large ball mill and achieve finer mill product that was closer to design. This paper summarizes life to date data analysis and improvements made by Minera Yanacocha as well as the grinding circuit optimisation study conducted by Metso Process Technology and Innovation.

Jan 1, 2012

By S. Kelebek, B. Nanthakumar

ABSTRACT The sensitivity of sulphide minerals towards oxidation depends on the mineralogical makeup and nature of sulphide ores. This paper focuses on chalcopyrite behaviour in a nickel-copper sulphide- ore matrix that was aged in the mine-site stockpiles. Results of collectorless, collector-induced flotation and recovery by size are presented following a discussion of XPS analysis that was used to gain insight into oxidative alteration of chalcopyrite’s surface chemistry. Chalcopyrite maintains its high flotation activity despite exposure to weeks of oxidative conditions. It is concluded that chalcopyrite is quite tolerant to stockpile oxidation due to various factors related to alteration of its surface chemistry.

Jan 1, 2012

By Ruilin Yang

The following simple equations are frequently used within the blast vibration community;PPA f PPV v = 2p · , PPV f PPD d = 2p · ,a f PPV PPA 2p = , and v f PPD PPV 2p = where, PPA is the peak particle acceleration, PPV is the peak particle velocity, PPD is the peak particle displacement, and fa , fv , and fd are the frequency of the particle acceleration, particle velocity, and particle displacement vibration waveforms, respectively. Conceptually, the frequency should be selected to be the frequency of a simple sinusoidal wave that is used to approximate the blast vibration. In the literature, f is sometimes chosen as the dominant frequency (fdm) estimated from the Fast Fourier Transform (FFT) of the blast vibration wave, on other occasions, f is chosen to be the principal frequency (fpr) from the vibration cycle with the peak vibration amplitude.

Jan 1, 2012

By Gaifeng Xue, Lijun Lu, Honghui Fang, Jiannyang Hwang

"Steel slag has been stockpiled in many steel mills due to its poor performance in various construction related applications. Free lime in steel slag has been considered as a major barrier for its utilizations. Composite of steel slag and powders of granulated blast furnace slag have been found an excellent cementitious material for concrete. Portland cement is not required in this kind of concrete. Concretes with various amounts of steel slag and powders of granulated blast furnace slag additions have been investigated. Physical and chemical properties of the products were examined. High performance concrete can be obtained. Field testing of the concrete products was conducted for various applications, including buildings and pavements, and the results demonstrated the soundness of the concrete. Drill cores of field tested concrete, with ages up to 26 years, were examined for the microstructures under SEM.IntroductionIn the steel industry, a major source of the solid waste is steel slag. Steel slag has poor stability in construction applications. This is a major reason that only a small amount of steel slag has been utilized. Some of the reported applications include the land filling/creation in the sea, road base materials, soil treatment for acid neutralization and micronutrients supply, and sintering aid in the sintering plant of the steel industry [1].To solve the stability problem for using steel slag as construction materials, the common approach is to find a method capable of depressing or eliminating the expansion of steel slag. Free lime in steel slag is the major component that causes the expansion. Aging and hydration pretreatment of free lime in steel slag are the well known methods for increasing the steel slag stability. However, there has been limited success on these approaches due to that a large portion of free lime is locked in the grains during the pretreatment process."

Jan 1, 2012

By R. K. Rajamani

Discrete Element Method simulation of charge motion in ball, SAG and autogenous mills has become a standard for design of mill internals, power draft evaluation, etc. Both two-dimensional and three-dimensional codes are being used. The two-dimensional code dominates the user market since the code completes a simulation in one or two hours. On the other hand, three-dimensional codes have been in the domain of specialists who can handle the complexity of the code and have access to parallel computing hardware. For the first time, this barrier is overcome via computing with graphic processing units (GPU). Commodity graphics cards now allow parallel computation with hundreds of processors. It is shown that the computational time has been reduced by a factor of fifty using GPU computing. Hence, SAG charge simulation results in three dimensions are achievable in a few hours using affordable desktop machines. The GPU computing shown here enables the three dimensional simulation into a manageable daily task for mill designers and researchers. On the technical side, the simulations can be elevated to a higher level of complexity to simulate breakage and transport. First, the speedup factor of fifty is established for the Nvidia GeForce GTX 580 graphics card. Next, four simulation tasks, consisting of AG, SAG and ball mills are reported. The simulation of AG and SAG mills are completed in less than 8 hours. The ball mill simulation with 1.25 million spheres is completed in 27 hours. In the near future, as the graphic card hardware advances the compute time can be halved.

Jan 1, 2012

By Sergio Neves Monteiro, Nuã Simonassi, Helvio Pessanha Guimarães Santafé Jr.

"Thermoset polymers, like the polyester, become harder with increasing temperature owing to molecular crosslink formation, which is a thermal benefit for composite matrix applications. Natural lignocellulosic fibers, however, have low thermal resistance and tend to degrade with increasing temperature. Therefore, the combination of a lignocellulosic fiber, as reinforcement, with a thermoset polymer, as the matrix, results in a composite material with complex thermal behavior. In the present work, a thermal analysis was conducted on polyester composites with different amounts of coir fibers. Both TGA and DTG curves were analyzed to determine the effect of the coir fiber on the thermal resistance of the composites. It was found that the coir fiber sensibly affects the thermal behavior of the polyester matrix for fiber amounts above 10% in volume. This effect is associated with an increase in thermal degradation.IntroductionIn recent years, there has been an increase application of natural fibers as reinforcement of polymer matrix composites in several industrial sectors, with special participation in automobile components [1-3]. Figure 1 illustrates the different components of a modem BMW sedan that are fabricated with lignocellulosic reinforced polymer composites."

Jan 1, 2012

By David G. Dixon, Maziar Eghbalnia

"Gold and silver nanoparticles (NPs) were deposited on pyrite at ambient temperature from colloidal solutions prepared by reduction of hydrogen tetrachloroaurate or silver nitrate by sodium sulfide or sodium tetrahydridoborate. The nanoparticles were characterized using Ultraviolet-Visible (UV-Vis) spectroscopy and the experimental spectra were fitted using Mie - Gans modeling. The modified pyrite was investigated using Electrochemical Impedance Spectroscopy (EIS). Electrodes were prepared from both natural and modified pyrite samples and were modeled using an equivalent circuit (EC) based on the EIS data. The comparison of the results revealed a decrease in charge transfer resistance for the ferric ferrous redox couple associated with the modified pyrite. From this behavior it is concluded that the electronic transport between the nanoparticles and the electrode surface over distances in nanometer scale is enhanced. Nanoparticles below a certain size act as quantum dots due to electronic confmement. Decreased charged transfer resistance at the nanometer scale may be caused by electron transport through tunneling mechanism via quantum dots.IntroductionIn recent years, considerable attention has been focused on the synthesis and study of Metal nanoparticles due to their potential applications in the fields of physics, chemistry, biology, medicine, material science and their interdisciplinary fields[!]. When material is nano-sized, the physical properties deviate markedly from those of bulk material, however, this effect is highly dependent on the particle size, interparticle distance, and morphology of the nanoparticles [2].An extremely small region of space defmed in a semiconductor material in order of nanometers is called a quantum dot, a term coined by Reed [3]. The three dimensional confinement of quantum dots can change properties of the excitons in comparison to free excitons in a bulk material [4]. Nanoparticles behave electronically as zero-dimensional (restricted in all three dimensions) quantum dots when the de Broglie wavelength of the valence electrons and the particle are in the same size range.As Reed [3] explains electrons confined in a plane have no freedom to move the third dimension. Those confined in a quantum wire are only free to move in one dimension, and those confined in a quantum dot are not free in to move in any dimension. An electron inside a cube of material IO nm on a side is confined to a point."

Jan 1, 2012

By Yuanbo Zhang, Daoyuan Zhang, Youlian Zhou, Guanghui Li, Tao Jiang

"Modified humic acid (MHA) has been developed by Central South University (CSU) and authorized in China. It has been reported that MHA is an effective binder for oxidized pellets prepared from specularite concentrates. In this research, effects of MHA binder on roasting behaviors of the specularite pellets are studied. MHA is an organic binder, containing much carbon, hydrogen, oxygen, etc. During the roasting, MHA can provide some heat because of combustion of hydrocarbon, which is beneficial for the recrystallization of Fe2O3 in the specularite pellets at high temperature. Simultaneously, part of hematite particles within the pellets are firstly reduced to magnetite, then, magnetite is oxidized into secondary hematite, which obviously improves the roasting performance of specularite pellets.IntroductionOxidized pellets have been widely used in steel production as a kind of high quality burden for blast furnace ironmaking [1]. In recent years, production of oxidized pellets is developing very fast. Therefore, the supply of high quality magnetite concentrates, which is the most suitable for pellet production, becomes scarce. It is imperative to pursue new alternative materials for oxidized pellet production [2]. Specularite concentrates have attracted widespread attention due to the advantages of high total Fe grade and low impurity content. However, due to the poor ballability and firing performance, specularite has not yet been widely applied into pellet production [3, 4]."

Jan 1, 2012

By Alberto Oalvez, Lucya Yunus, Pengfii Tan

"Laboratory flotation tests of slow cooled converter slag have showed that 92.5% copper recovery at the copper cut-off grade of 24 - 25 % can be achieved by using a 50:50 ratio of DSP330 and SIBX (sodium isobutyl xanthate) at the natural pH of 7 and with a grinding time of 18.5 minutes. 70ìéç is the P80 achieved at this grinding time. MIBC is the frother and the solid content of the flotation feed was 46%. In the plant trials, two types of collectors at two different feed particle sizes for both the normal and slow cooled slag were operated. The particle size was controlled by the feed rate. The P80 of 75 ìçé at a feed rate between 32 - 36 t/h were tested. The plant trials have demonstrated that the copper recovery in the milling and flotation process of the slow cooled slags was improved by 3%. IntroductionIt is proposed to float the slow cooled converter slag, in the auxiliary circuit of the copper concentrator at Mount Isa, by using the processing conditions identified from several laboratory flotation tests. Among these laboratory tests, one produced a copper recovery of 4 % higher than those achieved from a normal cooled slag with the same slag feed grade and the same copper content (24 - 26 %) in the concentrate. These test conditions were selected for further studies.Laboratory Test Work and Plant TrialsThere has been a lot of work conducted under laboratory and plant conditions [1]. However, the achieved results did not justify their total implementation in the Mount Isa Copper Concentrator. Initially, the lab trials were carried out with slag cooled 100% in air; then it was changed to combined cooling for 12 h with air and 2.5 days with water sprays. The reason for this change was the shortage of space when the slag was cooled 100% in air, as it takes several days to achieve safe temperatures for its removal. The San Manuel Copper Smelter has reported that their slag was left for air cooling in pits for 8 h and then was followed by water cooling for 2-3 days [2]"

Jan 1, 2012

By R. Khanna, I. Mansuri, S. Devasahayam

"Recycling polymer based end-of-life materials as carbon resources for a partial replacement of coke/coal can make important contributions towards enhancing the environmental sustainability of steelmaking processes. An in-depth high temperature (1550°C) investigation has been carried on waste CDs/DVDs focussed specifically on char generation, characterization and dissolution into molten iron. The simultaneous presence of carbon and oxygen in polymeric chains on polycarbonate substrates resulted in the generation of a significant pore structure and exposed surfaces. Carbon dissolution studies into molten iron were carried out on the raw polymer as well on chars; high levels of carbon pick-up were observed in both cases after 15 minutes of contact at high temperatures. INTRODUCTIONOver the past sixty years, plastics have played an important part of our daily lives and are being increasingly used in all aspects of the global economy. More than 260 million tons of plastics are produced annually worldwide. Their rapid growth and extensive utilization with a short life span (such as packaging) has created a massive waste problem. Although the waste plastic component in municipal solid waste (MSW) amounts to only about 10 %, plastics have a high volume-to-weight ratio and these are generally not biodegradable. In Australia, ~19.20 % of plastics were recycled in 2009-2010 (PACIA, 2010); with the total consumption being estimated at 1,501,258 tonnes, 288,194 tonnes of plastics were recycled. There are serious environmental concerns with the two key waste management options, i.e. land filling and incineration, and there exists an urgent need for developing alternative recycling approaches. In this paper, we focus our attention on recycling waste CDs/DVDs polycarbonate substrates as a carbon resource in steelmaking.CDs/DVDs used for music/data/image are made from aromatic polycarbonate resin (hereafter abbreviated PC). This resin is also widely used as an engineering plastic in applications such as automobiles, mobile phones, notebook type personal computers, cameras & video cameras, electric & electronic appliances, fire equipment, life & living goods, roofing sheets, etc. High consumption and growth (~10% annually) of PC utilization is attributed to its excellent properties such as outstanding impact resistance, transparency, heat resistance, and dimensional stability. The molecular formula and composition of PC resin is given below:"

Jan 1, 2012

By Lawrence Nordell

A Conjugate Anvil-Hammer Mill (CAHM) has the potential to replace conventional crushers and SAG mills, with their respective conveyors and stockpiles, in a SABC circuit. It may improve comminution circuit efficiency by 100%. CAHM compresses rock in a more efficient way, similar to 19th century stamp mills, which follows the fundamental research of Schönert (1990 & 1996). CAHM efficiency is being proven through the use of ROCKY (2011) Discrete Element Method (DEM). ROCKY features allow it to simulate realistic comminution. CAHM is customizable with many geometries that are rock-property specific. ROCKY?s wear modeling compliments the structural integrity of the design.

Jan 1, 2012

By P. Rambalee

A multiple coal fired boiler house provides steam for utility usage in various production plants. Maintaining stable header pressure and boiler availability is of critical importance for downstream consumers. Advanced Process Control comprising of a G2 based expert system and Model Predictive Control was implemented to improve the boiler house performance. The results yielded improvements in the main header pressure stability, reduction in boiler saturation and significant saving in coal consumption. All information used for this document is from a published whitepaper written and led by Prevlen Rambalee (Anglo Platinum) and Gustaf Gous (BluESP) titled, ?Control and Stabilization of a Multiple Boiler Plant: An APC Approach?.

Jan 1, 2012

In 2009 Newmont Mining Corporation?s annual global spend on grinding media reached $94M USD, having doubled in the five years since 2004. The major contributing factor to the spend escalation during this period was unit consumable price, with total media consumption also rising as a function of annual ore tonnes milled. In an effort to better understand and manage the growth of this expenditure a significant supply chain management program was implemented. This was complemented by a series of technical initiatives focussed on grinding media specifications, quality management and the prediction of grinding media wear rate as a function of physical ore characteristics. This paper discusses the methodology and outcomes of these activities.

Jan 1, 2012

By P. van Zyl, M. Lombaard

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Jan 1, 2012

By Thomas Schemmel, Bertram Kesseiheim, Helge Jansen, Uwe Kreme

"During the last decades the refractory life time of the different aggregates of the secondary aluminium production was improved significantly. However, each repair and installation of refractory material affects the operating schedule and can cause costs in the million range. The downtime of just one melting furnace generate costs of 100.000 to 400.000 $ per day. Besides cooling down of the furnace and its repair, the heating-up procedure accounts for the longest time of the shutdown. Usually, heating-up of low cement or ultra low cement castables takes 120 to 150 hours. In order to reduce such expensive downtimes Refratechnik developed a unique and novel product series: Nanobond. These materials can be heated-up in only a third of the usual time. This paper talks about the theoretical aspects, as well as the mechanical and physical properties and especially practical experience of using Nanobond.Theoretical Aspects and Laboratory ResultsCement containing castables such as RCC, MCC, LCC or ULCC are considered standard in many refractory applications. Over the years a wide range of possible raw materials and practical installation methods were developed. However, all of these cement bonded refractory mixes possess one main important drawback. Such materials are characterized by the hydration of the cement bonding. As a result the physical bonded and the hydraulic water has to be removed in a relatively complicated drying procedure. The hydraulic water specifically demands a very careful and cautious heating up procedure. Most of the dreaded steam explosions can occur at a furnace temperature of approx. 250 oC. [1] To avoid such destructions, the heating-up of a new lined or repaired furnace can be very complex and slow. Depending on the furnace or the casted part a drying time of several days with long curing times are common."

Jan 1, 2012

Experimental determination of the response of an AG/SAG mill treating two components of significantly different impact resistance is challenging for two main reasons: firstly, small scale laboratory tests have yet to be confirmed as valid representations of the full scale milling environment, and secondly pilot plant testing requires 10-20 tonnes of ore per scenario which precludes the use of drill core, rendering the process very expensive. In order to mitigate these difficulties, modelling was considered as a potential way forward. However, as the JKSimMet AG/SAG model currently has no capacity to simulate the interaction of two ore types with differing impact resistance, density and/or feed size distributions, an alternative modelling approach was developed. This approach aims to essentially calibrate the AG/SAG process under a set of given conditions, for which survey data and the ore properties of the main components in the feed blend already exist. This paper describes a new conceptual model, which provides a simplified approach for investigating the multi-component behaviour of two ores of differing hardness/SG in a given AG/SAG milling environment, and which can potentially be used for scale-up from laboratory/pilot testwork and geometallurgical estimation of throughput.

Jan 1, 2012

By K. Becerra, D. G. Almond, T. D. Maru

"Nkomati Nickel Mine in South Africa processes one of the world’s hardest ores in a 375k TPM autogenous grinding circuit. The plant employs an unconventional processing circuit, comprising a primary autogenous mill (AG or FAG) and pebble crushing circuit followed by a secondary hybrid pebble/ball mill and classification cyclone cluster.Advanced Process Control (APC) or Expert Control is now generally accepted as an advantage in most modern high capacity concentrator grinding circuits. This paper reviews the installation of model predictive control at Nkomati and examines the results and benefits of installation in an autogenous mill during plant ramp-up. The paper also demonstrates how predefining process control objectives together with good plant and supplier cooperation can achieve a robust and reliable APC implementation on a very short site program.The results conclusively demonstrate operational and economic benefits during circuit operation with the advanced process control system ON. Production performance and circuit stability were significantly better than during manual control."

Jan 1, 2012