Search Documents

By Shahid Islam, Lucian Bogdan

Deep and large diameter drilled shafts use mostly bundles of Grade 60 (415 MPa) reinforcing bars as longitudinal reinforcement with rebar splices to make it longer. Lower Grade steel requires large number of bars which result in rebar congestion and difficulty in placing concrete. This leads to increased labor cost for fabrication and installation. By utilizing larger size and higher strength threadbar, the congestion of rebar can be reduced significantly and bundling of bars can be avoided. The lap splices are replaced with simple threaded couplers and end hooks are replaced with end terminators. Threadbar conforms to ASTM A615-15 and can be epoxy coated if required for corrosion protection. This paper describes an attractive value engineering of replacing Grade 60 (415 MPa) bundle of rebars with larger diameter Grade 75 (515 MPa), Grade 80 (550 MPa) and Grade 100 (690 MPa) threaded bars and threaded couplers in some specific drilled shaft projects in the USA. INTRODUCTION A drilled shaft which may also be referred to as drilled piers, caissons, cast-in-drilled-hole piles and bored piles is the key element to the foundation of massive structure. They are used for tall buildings, bridges and foundations for other applications such as retaining walls, sound walls, signs, or high mast lighting. Drilled shaft foundations are typically 3 to 12 feet (0.9m to 3.7m) in diameter cast-in-place deep foundation elements constructed in a drilled hole that is stabilized to allow controlled placement of reinforcing steel and concrete. Drilled shafts for transportation structures are commonly used to depths of up to 200 ft (61m) in the USA. Drilled shafts can be installed in a variety of soil and rock profiles, and are most efficiently utilized where a strong bearing layer is present. The reinforcing cage is typically lowered into position within the hole and then concrete placed through the center of the shaft, flowing from bottom to top through the reinforcement to fill the hole.

Jan 1, 2018

By T. N. Aleksandrova, A. V. Afanasova

"The research is aimed at solving the problem of enrichment of sulphide ores, counting for more than 40% of the reserves in Russia. The aim of the research is to develop and scientifically substantiate the scheme for processing this type of ores in order to extract fine-dispersed noble metal particles (FNMP). In this work samples of sulfide carbonaceous ore and flotation concentrates were analyzed using complex precision methods of analysis: electron microscopy, spectral analysis with induction plasma, complex thermogravimetric analyzes, etc. Data on the composition of the organic constituent of the samples were obtained with the usage of complex thermogravimetric analysis. The presence of various types of kerogen and bitumen has been established. Experimental studies on the coarsening of FNMP from the initial ore and flotation concentrates using electromagnetic radiation have shown the effectiveness of this coalescence method. The data on the elemental composition of the samples and the amount of FNMP were obtained. Thus, studies on the extraction of FNMP from carbon sulphide ore have shown the possibility of effective usage of combination of electromagnetic action and classical enrichment methods to extract fine particles of noble metals. INTRODUCTION Due to the depletion of free-milling raw materials the involvement of new types of deposits is the strategy of developing mining industry of Russia. The black shale raw materials show interest as a non-traditional source of precious metals since its genetic and positional gold-carbon connection. Muruntau, Sukhoi Log, Bakyrchik, Natalkinsky, Nezhdaninskoye, Olimpiadinsky, Homsen and others are the examples of well-known deposits of the black shale formation [1]. In fact the main gold-dispersed regions of Russia are composed of black-shale strata. Review of literature [2-5] shows that in recent years in almost all deposits of the black shale formation metals of the platinum group (PGM) were detected that significantly increases their practical importance."

Jan 1, 2018

By Venkataramana Runkana, Pradip Gautham, Beena Rai, Sreedhar Reddy

"IT enabled platforms are the key to provide an integrated view of the business activity or an enterprise as a whole. Attempts to integrate all functions in an enterprise such as mine-to-market initiatives, wherever and to whatever extent implemented, have provided significant benefits to the industry. The transformative potential of IT enabled integration platforms is illustrated in this communication from our own work in this field. TCS PREMAP (Platform for the Realization of Materials and Products) is a knowledge-driven engineering design and development platform which leverages modeling and simulation and artificial intelligence into the engineering design process. We illustrate the customization of this generic platform for the design and optimization of mineral processing plants in an integrated manner. TCS PEACOCK (Process and Equipment Analytics for Optimization and Control) has been developed to enable automation of data analytics in the operating plants. We illustrate its utility and power in improving the plant performance with the help of case studies from our work on pelletization of iron ores and optimization of flotation plants. INTRODUCTION We are living in an exciting digital era. With the advent of cloud computing and social media on the one hand and rapid advances being made in several research areas of interest to us in the minerals and metals industry such as artificial intelligence (AI) & machine learning, robotics, unmanned vehicles including drones, big data analytics, 3D printing, sensor technologies, renewable energies and internet of things (IoT), many disruptive transformations in our industry are on the horizon. Recent advances in information technology (IT) and knowledge engineering, in combination with appropriate domain expertise, that is, our enhanced understanding of the underlying science of mining and mineral processing operations and the availability of a variety of powerful modeling-simulation tools make it possible to address the challenging problems facing the mining and mineral processing industry, in an integrated manner."

Jan 1, 2018

By Bo-Hyun Kim, Mark K. Larson

"While faults are commonly simulated as a single planar or non-planar interface for a safety or stability analysis in underground mining excavation, the real 3D structure of a fault is often very complex with different branches that reactivate at different times. Furthermore, these branches are zones of non-zero thickness where material continuously undergoes damage even during interseismic periods. In this study, the initiation and the initial evolution of a strike-slip fault was modeled using the FLAC3D™ software program. The initial and boundary conditions are simplified and mimic the Riedel shear experiment and the constitutive model in the literature. The FLAC3D model successfully replicates and creates the 3D fault zone as a strike-slip type structure in the entire thickness of the model. The strike-slip fault structure and normal displacement result in the formation of valleys in the model. Three panels of a longwall excavation are virtually placed and excavated beneath a main valley. The characteristics of stored and dissipated energy associated with the panel excavations are examined and observed at different stages of shear strain in the fault to evaluate bump potential. Depending on the shear strain in the fault, the energy characteristics adjacent to the longwall panels present different degrees of bump potential, which is not possible to capture by conventional fault simulation using an interface.INTRODUCTIONThis paper is part of an effort by the National Institute for Occupational Safety and Health (NIOSH) to identify risk factors associated with bump-prone potential in highly stressed ground conditions. More specifically, this paper reports an exploratory effort with an unconventional approach using a numerical tool to try to better understand a possible scenario where bump risk might be increased—that is, a scenario involving a strike-slip fault. The objective is to assess whether a numerical tool might be useful or practical in forecasting bump potential associated with a strike-slip fault for a typical, structural geologic setting."

Jan 1, 2018

By A. Ang-Ug, L. Gurieff

"The Phu Kham Cu-Au mine in Laos is owned and operated by Phu Bia Mining Limited. The deposit is a complex and low grade Cu-Au porphyry ore. The rougher feed has a particle size distribution of 80% passing 110 µm, and the rougher concentrate is reground for cleaning to 80% passing 25 µm. The Cu losses in the cleaning circuit are primarily in the <12 µm fraction. A randomised paired ON-OFF test of magnetic conditioning in one of the two parallel cleaner 1 circuits was undertaken. The results showed that with magnetic conditioning there was approximately a 10% reduction in the <12 µm Cu distribution in the cleaner 1 tail to a 98% level of confidence. The Cu distribution in the <12µm fraction is a less variable measure of changes in the <12µm Cu recovery, therefore, this was used to evaluate the impact of magnetic conditioning. Subsequently, magnetic conditioning was installed in both cleaner 1 circuits and the plant results monitored after this installation. Comparing the plant results immediately before and after this installation showed that there was a 20% reduction in <12µm Cu losses to the cleaner tail. INTRODUCTION The Cu-Au, Phu Kham Mine (PKM) is located within PanAust's Phu Bia Mining Contract Area in Laos, approximately 140 kilometres from the capital city, Vientiane. PKM is PanAust's flagship operation and the significant cash flow generated by PKM has supported PanAust’s growth, while contributing to a strong balance sheet. PKM comprises an open-pit mine and a conventional milling and flotation operation that produces and exports a Cu and precious metals concentrate. The concentrate contains around 23% Cu, 6 ppm Au and up to 35 ppm silver. Process Overview The PKM deposit consists of complex heterogeneous mineralogy horizons of Cu-Au stockwork and skarn mineralisation. It contains areas of soft-leached zones, overlying transition zones and supergene chalcocite dominant secondary Cu mineralisation and clay-rich gangue. Areas of high As and Zn also pose a challenge in treating the highly variable ore. In addition, hardness of the ore increases with deposit depth. The ROM is hauled to a primary gyratory crusher to produce a coarse ore stockpile with size distribution suitable for the 13 MW semi-autogenous mill. The SAG product feeds two parallel ball mills each equipped with a cyclone cluster producing a product particle size distribution of 80% passing 110 µm. The conventional flotation circuit consists of two parallel rougher banks. The rougher concentrates feed the regrind cyclone where the underflow is split and reports to two parallel, 3MW, M10000 IsaMills. The regrind mill discharge combines with the regrind cyclone overflow with a product particle size distribution 80% passing 25 µm and reports to the Jameson cell."

Jan 1, 2018

By Jessica M. Wempen, William G. Pariseau, Michael K. McCarter

"Quantitative analysis of mine-wide subsidence at the kilometer scale and details of stress distribution about an advancing longwall face are estimated using an adaptation of the finite element method. The method is well suited to the tasks at hand. For greater realism, variability of strata properties is taken into account as are the effects of joints and cleats on elastic moduli and strengths. Evolution of pillar stress and entry closure remote from the face is readily quantified in a series of analyses that simulate face advance. Computed results compare favorably with the evolution of closure measurements about an instrumented pillar in a two-entry headgate. The appropriateness of the finite element method is confirmed. This method is based on first principles that avoid empirical schemes of uncertain applicability and numerical models “calibrated” by fitting computer output to mine measurements.INTRODUCTIONMine-induced seismicity is intimately related to strata mechanics associated with longwall coal mining and room and pillar mining, as well. Strata deformed beyond an elastic limit often tend to fail rapidly by brittle fracture and, thus, to emit acoustic signals in the form of elastic waves. Understanding the induced seismicity in coal mining offers the potential for early warning of hazardous conditions. Many years of experience with seismic phenomena associated with hardrock mining suggest considerable complexity should be expected. However, recent coal mine studies (Pariseau, 2014; Pariseau, 2015; Pariseau and McCarter, 2015; Pariseau and McCarter, 2016) have shown high correlations of seismicity with element failures in finite element simulations. The main lesson learned from these studies is one elaborated by Iannacchione et al (2005); deviation from normal activity is an early warning of ground control difficulty. For example, an abrupt increase in seismic event rate, or equivalently, an increase in element failure in finite element simulation of panel advance, is a cautionary indication for ground control. Present and past study results demonstrate the effectiveness of finite element simulations for mine design and early detection of potential ground control issues."

Jan 1, 2018

By S. Gering, R. Ruiz, C. H. Calderon-Arteaga, J. Barrios

"INTRODUCTION Located in the northeast corner of Zacatecas State, Mexico, the Peñasquito Operation is comprised of the Peñasco and Chile Colorado (Brecha Azul) deposits. Open pit mining (pre-stripping) began in 2010 and full production commenced during 2011. The open pit mines feed both a sulphide concentrator (mill) and a heap leach pad. The project is owned by Goldcorp, Inc. Penasquito is a poly metallic deposit with Au, Ag, Zn and Pb being recovered as payable metals. As a consequence of lower grade ores expected with advancing mine-life Peñasquito is facing a declining metal production profile. To maximize returns and asset value plant modifications including the addition of a carbon pre-float circuit and a pyrite leach circuit to improve recovery are currently being undertaken. This carbon pre-float circuit will enable the recovery of precious and base metals from carbonaceous sediments. This material is currently being stockpiled. With the associated increase in complexity in the process circuit, the requirement of the ore control system to accurately predict ore feed characteristics is critical to maximizing metal recovery at the Penasquito operation. The addition of the carbon pre-float circuit was also a key driver in allowing the Chile Colorado open pit to be developed. These conditions alongside Goldcorp’s drive to increase profitability, and maximize net asset value has created challenges. These challenges are numerous and are multifaceted, however the ability to accurately route materials from the ore control system is critical to site success, and some of these challenges have been overcome by the adoption and implementation of a new ore control (OC) technology. Examples of these technological innovations in the ore control program are discussed in this paper and include improvements in geo-modeling, material routing and reconciliation. Successful implementation of these elements has led to significant improvements in selectivity, performance, and data management, while reducing the variance between planning and execution, thus helping to drive overall improvement across the operation."

Jan 1, 2018

By Ihsan B. Tulu, Keith A. Heasley, Aanand Nandula

"The objective of this paper is to present the development of a software tool that will assist in an area calculation of the Analysis of Roof Bolting Systems (ARBS) support intensity while incorporating more detailed geology, stress, and intersection span input. In this area ARBS tool, a detailed CMRR distribution can be determined from the available geologic database at the mine. In addition, the overburden and multiple-seam stresses, as obtained from the boundary-element program LaModel, can be converted to a “pseudo-depth” which is then used as the depth input to the area ARBS calculation. Finally, the section-specific intersection spans can be determined from the mine design for input to the calculation. All this detailed area input information for ARBS is handled by the latest version of the Stability Mapping (StabMap) program, which now outputs an area ARBS suggested support density given the required input parameters. This final ARBS grid can be plotted, analyzed and overlaid on the mine map for optimum use in support design and for presentation to production personnel.INTRODUCTIONSince the inception of roof bolts in the 1940s, there has been a lack of a universally accepted roof bolting design method (Mark, 2002; Mark and Pappas, 2012). To address this situation, the National Institute of Occupational Safety and Hazard (NIOSH) developed roof support design guidelines, which were incorporated into a computer program called the Analysis of Roof Bolting Systems (ARBS). These guidelines were based on the effects of roof quality, stress, and mine geometry (Mark, Molinda and Dolinar, 2001). The roof rock quality in ARBS is represented by the Coal Mine Roof Rating (CMRR), the depth is used as a surrogate for the stress, and the intersection span serves to represent the mine geometry (Mark, Molinda and Dolinar, 2001). These three input parameters are used in the fundamental, empirically derived equation of ARBS to calculate a required support density factor, called ARBS, (Mark, Molinda and Dolinar, 2001):"

Jan 1, 2018

By T. M. Russell

"Face mapping is a simple but invaluable means of geological and geotechnical data acquisition whereby intact rock properties, rock mass properties, discontinuity properties, and structural orientation can be assessed. Although traditionally done via direct contact with the mapping face through techniques such as line mapping or window mapping, remote face mapping using various digital techniques has become increasingly popular in recent years. Sishen is a large open pit mining operation requiring a comprehensive geotechnical data-set to evaluate pit wall design and stability with the necessary level of confidence. Geotechnical borehole data, face mapping data, geotechnical laboratory testing data, and implicit structural models provide the main sources of this information. Although a large geotechnical borehole database has always been maintained at the mine, face mapping has in the past been restricted to sporadic and isolated stability assessments. In 2013 the mine acquired a terrestrial laser scanner with the resolution, photographic capabilities, and software required to carry out geotechnical face mapping. A face mapping procedure was set up based on accepted face mapping methods, the data requirements of the mine, and capabilities of the laser scanner system. Mapping data obtained from the scans was integrated into the Acquire geological data management system, a purpose-designed structured query language (SQL) database system used for storing the mine’s geotechnical data. Within the geotechnical design process, having face mapping data available has improved confidence in the properties of the rock mass and structural environment, allowing for better definition of geotechnical design sectors. Overall, the face mapping and geotechnical analysis features of the terrestrial laser scanner in use make it an invaluable geotechnical data capture tool, provided a system is in place to store mapping data in a manner that allows for meaningful rock mass and structural information to be produced. IntroductionFundamental to the geotechnical design process is the acquisition of a reliable and complete geotechnical data-set. Geotechnical data acquisition will typically commence during the early stages of a project and continue well into the operational life of the mine, with the data confidence progressively increasing as the amount of data captured increases. Sishen mine currently bases all open pit geotechnical designs and geotechnical risk assessment on geotechnical borehole data in conjunction with interpreted structural models. Boreholes are logged and the data is captured in an ongoing process. This process forms the initial step in the geotechnical design and risk assessment process whereby the raw data is used to classify the strength properties for each lithology, provide inputs for geotechnical block models, and ultimately provide the inputs for slope design analyses. To date, borehole data has provided the only largescale, organized data-set for input into geotechnical analyses at Sishen. Although borehole data is the best and most comprehensive form of geotechnical data, there are some shortfalls that can be addressed by other data collection methods. These shortfalls are as follows."

Jan 1, 2018

By Stankusm John C., Xiaoting Li

"Quantitatively identifying the load on a steel king beam set is a complicated issue in designing the king beam structure at the slope bottom area. From an engineering perspective, understanding the nature and support mechanism of the king beam structure as a standing support is critical in identifying the calculation input parameters for the structure design software. Based on design practices in recent years and successful applications in several slope bottom intersections, the authors present a king beam design methodology, including qualitative analysis, quantitative calculation with a structural design software, and computer Finite Element Analysis (FEA) verification.Especially important is the concept of interaction and the confinement effect between the king beam structure and surrounding rocks, which is essential in designing a proper steel structure in terms of maintaining the roof stability, as well as saving the steel materials and costs of manufacture, labor, and delivery. This paper details the design methodology and applications in several underground slope bottom intersection designs, reaching the goals of improving roof stability and reducing costs.INTRODUCTION AND DESIGN METHODOLOGYCurrently, the load on a square or arch set is typically determined by either past empirical design experiences or known heights of roof falls in current or adjacent mines. These methods work but sometimes are too conservative from an engineering perspective. For example, when designing a king beam structure for an intersection, these methods may lead to a design with extremely large and heavy steel beams, which are not convenient for delivery and installation on-site, not to mention, costly. Therefore, accurately identifying the potential maximum load on the king beam structure is important for designing a safet, effective, and cost-efficient steel structure. Based on past several years’ practices and fundamentals of ground control and structural design engineering, the authors propose a design methodology including the following components:The nature and mechanism of effective roof support (qualitative analysis),Ground reaction curve,Interaction and confinement effect between bolts and steel standing support and surrounding rocks,Factors affecting the load conditions of the king beam set"

Jan 1, 2018

By R. Darlington, S. Ji

"High pressure die casting is a promising process to make thin-wall components with high dimensional accuracy and excellent surface quality. However, the non-uniformity is one of the important features in castings. The inhomogeneity in tensile properties and microstructural characteristics were studied for the castings with different thicknesses made by high pressure die-cast Al-Mg-Si alloys. For the local mechanical properties in the die-castings, the casting skin provided the highest, whereas the casting centre provided the lowest yield strength, UTS and elongation. The yield strength, UTS and elongation were significantly decreased towards the casting centre. The microstructural inhomogeneity is characterised by the segregation of coarse fragmented dendrites, the reduction of solute concentrations of Mg and Si, and the increase of porosity level from the surface to the centre of castings. The growth velocities of eutectic a-Al phase estimated using the Jackson-Hunt model confirm that the growth variation is larger in the thin castings than that in thick castings.INTRODUCTION Inhomogeneity is an inherent characteristic in as-cast microstructures of a variety of alloys because of their non-uniform chemistry, microstructure, defects, topology and the resultant mechanical properties in the different ranges of localization (Campbell, 2003). Generally, three types of inhomogeneities characterise casting microstructures, which include (a) the casting defects of shrinkage and gas porosity, misruns, cold shuts, inclusions, hot tears and hot spots; (b) the non-uniform microstructure from the surface to the centre of castings; and (c) the non-uniform microstructure from the dendrites grown from primary solidification and the structure formed during the subsequent eutectic solidification in inter-dendritic regions. The chemical composition and the morphology between the primary dendrites and the inter-dendritic eutectics also differ in the as-cast microstructure. Obviously, the inhomogeneity is different in the castings obtained from different casting processes."

Jan 1, 2018

By E. Karampinos, P. Morissette

"INTRODUCTION Ground support is a critical element in maintaining the stability of mining drives in deep and high stress mines. In challenging ground conditions, it is necessary to continuously explore ground support strategies that can control the resulting large deformations. It is an objective of mining operations to optimize the ground support by selecting both appropriate systems and the time of installation of each reinforcement element. A successful ground support strategy will result in the use of a system that ensures both the structural and operational integrity of the excavations and mitigates the need for rehabilitation. Preliminary ground support design is often based on empirical observations and methods. Once a design is implemented, field trials, observations and in situ pull tests are used to fine tune or improve the design. Although not often employed during this process, numerical modelling can provide helpful insights on the impact of different ground support strategies. In this respect, it is possible to explore the use of multiple options before selecting the most promising ground support system for implementation in field trials. The challenges associated with the numerical modelling of rock support for mines have been described by Lorig and Varona (2013) and Potvin (2017). The employed numerical models should capture all potential failure modes of reinforcement over the mining sequence of the excavation. In particular, it is important to emulate the observed in situ ground support performance, as well as the influence of the installation sequence of the support. However, the time and expertise required for this type of modelling of ground support is not often available at mine sites. Even when the expertise is available it requires a major time and commitment of resources to set up, run and calibrate the sophisticated models capable of explicitly capturing the behavior of ground support. Rock reinforcement is an integral part of all ground support systems used in underground mines. Long flexible tendons can reinforce the rock mass deeper into the walls and create a thicker reinforced shell around the underground excavation. This paper focuses on the optimization of the cable bolting strategy in squeezing conditions at the LaRonde Mine by integrating the 3D distinct element method (DEM) in the design process. A calibrated numerical model is used to investigate a series of cable bolt configurations and provide recommendations for the ground support design."

Jan 1, 2018

By C. H. Veloso

"Starch is the most widely used depressant in the reverse cationic flotation of iron ores. There is however, an indication from recent studies, that other polysaccharides may successfully replace them. When starches are used in the flotation of iron ores in the presence of quartz as gangue mineral, their strong adsorption on the surface of iron oxides can be explained by the molecular conformation between the available sites on the mineral surface and two hydroxyls of starches. However, when the gangue minerals are iron-bearing silicates, the strong interaction with starch can occur on these minerals since they have the same surface behaviour as iron oxide. In this work bench scale tests were conducted in order to generate scientific knowledge about other alternatives depressants for the flotation of iron ores. A magnetic pre-concentrate from a skarn iron ore processing plant was used as feed material for flotation tests. The reverse flotation approach was used to upgrade the iron content by removing complex ironbearing silicates. The depressants used in this study were: corn starch, dextrin, carboxymethyl cellulose (CMC) and humic acid. The tests were performed under different pH conditions in order to try to relate the efficiency of depression to the pH used during flotation. The results show the important role of pH as each depressant reached its best performance at different pH values. At alkaline pH the corn starch showed best depression performance while the humic acid is more efficient at pH close to neutrality.INTRODUCTIONIron corresponds to approximately 6% of earth’s crust composition (McDonough and Sun, 1995). It is the most used metal in our lives, some of its properties as resistance and facility to be shaped makes is replacement very difficult. The primary sources of iron on our planet are minerals. The iron-bearing minerals most commonly found in nature and economically exploited are magnetite [Fe3O4], hematite [Fe2O3], goethite [FeO(OH)] and siderite [FeCO3] (L O Filippov et al., 2014). These minerals are commonly associated with other minerals (most of the time not economically exploited) forming the so-called iron ore. Iron ore is the source of primary iron for the world’s iron and steel industries."

Jan 1, 2018

By Edson Charikinya, Pierre-Henri Koch

"The extraction of mineral values from ore requires liberation followed by separation steps. Liberation is achieved by size reduction operations which are energy inefficient processes typically dominating the energy consumption in a mineral concentrator. As the grade of ore reserves declines, future viability of mineral operations will be determined by energy costs of comminution. The application of high power microwave energy to secondary crusher products has been suggested as a possible commercially viable thermal treatment method for reducing comminution energy and improving value mineral liberation. Recent studies have shown that microwave pre-treatment of coarse sphalerite ore particles (> 5mm) at specific microwave heating energies (1-3 kWh/t), induces microfractures and creates new crack surfaces. This suggests that subsequent crushing of these microwave treated particles could yield enhanced liberation. However, limited studies have been carried out investigating the mode of breakage and the extent of enhanced liberation in that case. The objective of this study is to develop numerical methods for quantifying the extent of enhanced liberation and mode of breakage in crushed microwave treated and untreated particles. Sphalerite ore particles representing small (-5+4.75) mm, medium (-16+9.5) mm, and large (-25+19) mm HPGR and cone crushed particles were microwave treated at specific energies between 1-3 kWh/t. Cracks in the ore particles before and after microwave treatment were analysed with QEMSCAN and numerical models of the measured particles (before and after microwave treatment) were developed in MATLAB. The propagation of random and non-random cracks was investigated by simulating comminution of the modelled treated and untreated particles. Results of this study demonstrate that the breakage mechanism and the liberation of valuable minerals from gangue in microwave treated and untreated particles is significantly different. This study contributes to the development of numerical tools to quantify crack propagation in heterogeneous ore particles."

Jan 1, 2018

By A. Singh, C. Da Corte

"South Africa possess the biggest fluorspar reserves in the world followed closely by China. In light of the current commodity downturn this paper explores the use of Dense Media Separation (DMS) as a coarse pre-concentration method for two fluorspar deposits located in South Africa in which the dominant gangue is carbonate present in the form of dolomite and calcite. Heavy Liquid Separation indicated that conventional pre-concentration of the drill core samples from both deposits would result in unacceptably high fluorite CaF2 losses. At a maximum CaF2 loss to floats of 5% the benefit of DMS would be economically marginal and difficult to justify as a conventional pre-concentrator. In light of cashflow constraints, a twin flowsheet was proposed for the sole purposes of upfront cash generation in which the majority (67-77%) of the CaF2 would report to a high grade flotation plant in 38-41% of the mass whilst the rejects would be stockpiled for flotation at a later stage. Considering the proposed twin flowsheet approach the high grade product split was achieved using DMS and this paper documents the challenges encountered and results achieved. INTRODUCTION Fluorspar is the commercial term for the mineral fluorite (calcium fluoride, CaF2). Worldwide production of fluorspar is dominated by four countries namely China, Mexico, Mongolia and South Africa. Although South Africa is the fourth largest producer, it has the largest fluorspar reserves closely followed by China (U.S. Geological Survey, 2017a). Fluorspar is broadly categorized into two grades namely acid grade also referred to as acidspar (>97% CaF2); and sub-acid grade (ceramic and metallurgical grade) commonly referred to as metspar (=97% CaF2). Acid grade fluorspar is used for the production of hydrofluoric acid (HF) which in turn is used for the manufacture of fluorocarbons and semi-conductors in the electronics industry; metal processing; the production of insecticides, herbicides and cleaning detergents, and the manufacture of uranium tetrafluoride used to concentrate the uranium isotope 235 for use as a nuclear fuel (British Geological Survey 2010; Miller 2001). Ceramic grade fluorspar (85-95% CaF2) is used in the ceramic industry as a flux and opacifier in the production of glass and enamels. Ceramic grade fluorspar is also used to make coatings for welding rods and as a flux in the steel industry. Metallurgical grade fluorspar (60-85% CaF2) is primarily used in the steel industry as flux to reduce the melting temperature and remove impurities in steel making. Similarly metallurgical grade fluorspar is also used as flux in cement production to reduce energy consumption (British Geological Survey 2010; Miller 2001)."

Jan 1, 2018

By Karsten Hagenah, Tor Jensen, Jens Laugesen, Øyvind Fjukmoen, Lucy Brooks

This paper discusses operational environmental threshold levels for exploitation of mineral resources in the deep sea. Such criteria are needed to be able to monitor and control deep sea mining with respect to the stringent environmental requirements that are needed. It is recommended to use existing environmental threshold levels for comparable underwater activities. Fields of application are mainly but not exclusively seabed mining operation activities under the governance of the International Seabed Authority (ISA). The threshold levels and limits mentioned in this paper are proposed recommendations based on other activities than seabed mining but are a proven and accepted approach in other maritime industry activities. An example of such other activities with proven and accepted environmental threshold levels are Oil & Gas exploitation activities in the sea. Background The first exploitation of mineral resources in international waters is coming closer. Presently regulations for exploitation for mineral resources in the Area are being developed by the International Seabed Authority (ISA). The ISA regulations will contain the framework related to environmental monitoring of exploitation. However, the regulations will not contain operational environmental threshold levels for the Contractor.

Jan 1, 2018

By Antony Amberg, Gonzalo Saldías, Romke Kuyvenhoven, Catherine Souza, Heriban Soto, Francisco Soto

"Vizcachitas is an advanced stage copper–molybdenum porphyry deposit, fully owned by Los Andes Copper and located in Central Chile. The property contains an indicated resource of 1,038 million tonnes grading 0.37% Cu and 0.012% Mo, and an inferred resource of 318 million tonnes grading 0.345% Cu and 0.013% Mo (Coffey & Alquimia, 2014). The deposit occurs in the same geological belt as several other giant copper-molybdenum porphyry deposits including Río Blanco-Los Bronces, Los Pelambres-Pachon and El Teniente. In 2018, the original Preliminary Economic Assessment (PEA) study from 2014 was updated; this paper presents the geometallurgical testwork that was performed to support that update. The testwork focused on the metallurgical characterization of 40 DDH samples and the development of a more profound orebody knowledge by relating geological features with metallurgical performance. The scope of work included complete chemical and mineralogical QemSCAN characterization; SAG, ball mill and abrasion testing; complete rougher and cleaner kinetics including locked-cycle-test; environmental ABA and settling tests on rougher tailings. The results show that the ore can be classified as medium-hard, with a hardness that is slightly below the average for large Cu/Mo deposits in the region. A good correlation was found between lithology and breakage characteristics, implying that the specific energy consumption (kWh/t) is well correlated to rock type. The results of the flotation tests were very encouraging and did not show significant variability. An overall Cu recovery of 91% can be expected for the flotation circuit. The use of a relatively coarse primary grind size gave good final recovery and grade for both Cu and Mo, and deserves further attention in future work, as this impacts positively both energy consumption and water recovery.INTRODUCTION Los Andes Copper Ltd. is a Canadian exploration and development company focused on the acquisition, exploration and development of advanced stage copper deposits in Latin America. The company owns 100% of the Vizcachitas project in Chile, the largest copper deposit in the Americas not controlled by the majors. Vizcachitas is a copper-molybdenum porphyry deposit, located 120 km north of Santiago, in an area of very good infrastructure."

Jan 1, 2018

By Liu Jin

"In order to reduce the dosage costs and increase the economic benefits of a full floating process in a low grade complex multi-metals W-Mo ore, based on the study of the magnetic characteristics of the main gangue minerals, a joint process by magnetic separation and floatation technology is adopted. The first step of the flowsheet is to recover magnetite by magnetic separation, then remove the magnetic gangues by high gradient magnetic separation (HGMS) and finally recycle the W-Mo from the magnetically separated tailings by flotation. Results of the lab experiment show that in comparison with the full flotation process, the floatation feed tonnage of the combined flowsheet are only 46%. The grade and the recovery of Mo in the rough Mo-Bi concentrate is similar with the original one while the WO3 in the tungsten rough concentrate is increased from 3.85% to 6.64%. The dosage costs are reduced by 53%. The new process can significantly improve the plant economically. INTRODUCTION With the continuous exploitation of scheelite resources, the easily obtained resource is gradually depleting. The ""lean, fine and complex"" scheelite resource has become the main research object of tungsten beneficiation (Lou et al., 2010) (Xiao et al., 2013). The passive situation of tungsten beneficiation can be reversed by enhancing technological innovation and investment in science and technology, changing the business philosophy and mode of production, optimizing the process structure and process conditions, improving various technical indexes and reducing production costs of reagents, which will maximize economic benefits (Jiang et al., 2012 ) (Zhu et al., 2016). A polymetallic deposit of tungsten molybdenum bismuth original process adopts a full flotation process. With the expansion of stope mining, the content of valuable metals in the ore continues to decrease, resulting in a high cost per ton of concentrate produced and a low output value (Li et al., 2015)."

Jan 1, 2018

By C. Dorfling, W. A. Rossouw

"Hydrometallurgical processes used for metal recovery from waste printed circuit boards (PCBs) typically involve dismantling, shredding and physical separation prior to successive leaching stages for selective dissolution of different metals. The principles of the physical separation units are well understood, but valuable metal losses of more than 30 % can be incurred during these processing steps. The impact of the physical separation units’ performance on downstream leaching operations have not been defined; this prevents the development of a well-integrated process. The objective of this project was to determine to what extent the base metal leaching behavior depends on the physical separation pre-treatment. PCBs were shredded to 100 % passing 2 mm before physical separation by dense medium separation (DMS) as well as magnetic separation. Batch leaching tests using various concentrations of sulfuric acid were conducted on three feed fractions: (1) shredded PCBs without any physical separation, (2) heavy fraction recovered from DMS, and (3) non-magnetic fraction recovered from the DMS heavy fraction. DMS increased the metal content in the feed from 48 % to 75 % on a mass basis, but 70 % of the gold and 20 % of the copper reported to the light fraction. The application of magnetic separation to the heavy fraction produced by DMS removed 67 % and 61 % of the iron and nickel, respectively, while negligible amounts of non-magnetic metals were removed. Although DMS successfully concentrated the feed and magnetic separation removed the majority of iron and nickel, these steps did not result in any improvement in the rate or extent of copper leaching. Metals generally leached faster when the sulfuric acid concentration was increased from 1 M to 2.5 M; this effect was seen to be more pronounced for pretreated feed. INTRODUCTION The fast rate of technological development has led to a decrease in the service life of electronic devices. This is resulting in an increased rate of electronic waste generation. The recovery of metals from electronic waste is of environmental and economic interest. The majority of these metals are typically located on printed circuit boards (PCBs) within electronic devices (Tuncuk, Stazi et al., 2012). Hydrometallurgical processes are considered a viable option for small scale metal recovery from waste PCBs, and generally involve the following steps: disassembly for removal of hazardous and reusable parts, size reduction, physical separation, successive leaching stages for metal dissolution and finally recovery of metals from leach solutions."

Jan 1, 2018

By M. Samuels

"Block and panel cave mining methods are being increasingly proposed as they allow massive, deeply situated ore-bodies to be mined economically at a time when discovery rates of significant near surface deposits are declining. Cave-to-Mill, a mine-to-mill approach for block cave mines, defines ore block models with respect to both mine and mill performance. A cave-to-mill study for the New Afton block caving operation focused on identifying value opportunities related to fragmentation and sorting for a future lift as development progresses deeper. The lack of selectivity and potential for dilution associated with the block cave mining method results in many caving operations having to mine and either dispose of or process material that is below cut-off grade at certain stages of production. As an outcome of the study, the variation in cave fragmentation size and the sensitivity of mill throughput to feed size was examined. To evaluate the amenability of bulk and particle sorting, Prompt Gamma Neutron Activation Analysis and X-Ray Fluorescence sensors were tested. A conceptual bulk and particle sorting flowsheet is presented. Grade data from regular underground sampling was used to predict the performance of a bulk sorter. A heterogeneity analysis of material reporting to drawpoints helped to identify areas of the extraction level that experience high variations in grade and thereby stand to benefit from dedicated ore and waste material handling systems should underground bulk sorting be implemented.INTRODUCTION Block and panel caving are low-cost underground mass mining methods that are suitable for excavating weak, massive and steeply-dipping orebodies. Accordingly, cave mining methods have predominantly been used to mine copper porphyry and diamond bearing deposits. Due to the increasing depletion of near-surface orebodies, it is expected that block and panel caving methods will be increasingly used in the copper-gold industry. Their implementation holds significant potential to extend the life of existing open-pit operations by providing an economic means to access ore located at depths that are beyond the practical limits of open-pit mining. Examples of cave mines proposed for British Columbia include the Kwanika Mine, Red Chris underground, Kemess Underground project, and the Iron Cap and Mitchell cave mines of the Kerr-Sulphurets and Mitchell (KSM) project (Moose Mountain Technical Services, 2017; Imperial Metals, 2017; Golder Associates, 2017; Tetra Tech, 2016)."

Jan 1, 2018