Search Documents

By D. Paul Bishop, Kevin P. Plucknett, Hung-wei Liu

"Spark plasma sintering (SPS) process has been evaluated for producing the commercially pure (CP) Ti, TiAl and a TiAl-B4C composite. Comparisons were made between the materials in terms of the sintered density, resultant hardness and microstructures. In the present work, the titanium aluminide powders (Ti-48Al, producing a mixture of y-TiAl/a2-Ti3Al) were synthesised „in-house? using a simple reaction-sintering and mechanical attrition approach. This allowed various size distributions to be generated. The powders were then blended with a fine boron carbide (B4C) powder (up to 6 wt.%), and the resulting mixtures were consolidated using spark plasma sintering (SPS) under vacuum in graphite dies. An applied stress of 50 MPa was used for all SPS runs. The SPS parameters were varied in terms of the ultimate sintering temperature (up to 1300°C) and hold time (up to 10 minutes) for each material. It is demonstrated that high densities can be achieved this approach (exceeding 95% of theoretical, with optimised samples close to full density). Microstructural characterisation was conducted using optical microscopy, scanning electron microscopy, and X-ray diffraction. The B4C additions were seen to partially react with the TiAl to form reinforcements, such as TiCx and TiBx. Preliminary mechanical property assessment will also be briefly discussed.INTRODUCTION Titanium- and titanium aluminide-based alloys possess many unique properties, such as excellent corrosion resistance and high temperature strength, respectively (Cardarelli, 2001; Leyens & Peters, 2003). Compared to many other competing materials (e.g. stainless steel or Ni-based alloys), Ti- and TiAl-based alloys also have relatively low densities (~4.5 and ~3.9-4.1 g/cm3, respectively), which is critical for performance in aviation and automobile applications. However, the manufacturing cost is high, due to the expensive raw Ti material and difficulties in machining. TiAl-based alloys are particularly difficult to produce because of their limited ductility (Lütjering & Williams, 2007). To overcome those problems, powder metallurgy (PM) technologies have shown great potential as near-net shape processes for Ti- and TiAl-based alloys. The general PM process largely avoids laborious post-machining and minimises material use. In industrial production, the PM approach has been successfully utilised to manufacture aluminium- and iron-based alloys (Huo & Heath, 2008)."

Jan 1, 2017

By S. Tuylu, D. Adiguzel, A. Bascetin

"In recent years the fact that mining tailings cause serious environmental problems resulted in increasing number of studies about their disposal, storage and usability in various areas. Therefore the new studies about using the tailings for some purposes such as using in shotcrete or producing concrete have been increasing recently. The study is focused on applicability of tailings for producing shotcrete. Under this scope it is considered that mining tailings can bring many advantages in case of that they are used instead of sand, silt or fine aggregate in shotcrete applications. Most important advantages can be listed as decreasing shotcrete cost, decreasing amount if mining tailings to be disposed and the contribution to be provided on sustainable production of sources. The main objective of this study is the investigation of using mine tailing instead of fine aggregate in shotcrete. In this study, 10 shotcrete designs in different proportions were formed, and properties of the mixtures were identified. Then, the experimental results were statistically analyzed, the effects of the amount of the tailing material used on shotcrete properties were presented, and empirical approaches that can be used for the estimation of these properties were developed. INTRODUCTION The disposal of high amount mine tailing on the surface is caused a lot of problems in terms of environmental impact. Unfortunately, it is known that classic disposal techniques such as tailing dam cannot provide a solution these problems. The tailing dams which are usually used in the disposal of mining tailings bring along many problems in terms of cost, environment, and human health. So mine tailings are used in different production such as shotcrete. This technique is becoming increasingly common during recent years. The usability of mine tailings in brick and concrete production instead of cement and fine aggregate has been studied by many studies [1-4]. This situation has been promising for the usability of tailings in shotcrete which is commonly used for ground support especially in tunnels. Shotcrete (sprayed concrete) is applied mainly for construction of tunnels, shafts, renovation works and strengthening of slopes. Main advantage of shotcrete is fast development of strength, which quickly ensures stability of strengthened structure [5]. Shotcrete can be defined as spraying the grout consisting of water, aggregate, cement and optional additive mixture on the desired surface with a compressed air. According to the definition of the American Concrete Institute (ACI), it is the spraying of sprayed grout or concrete on a surface at high speed with air pressure [6]. In recent years, the use of shotcrete for the support of underground excavations is decreased in the mining industry. The design of shotcrete support for underground excavations is a very imprecise process. Strength and pumpability properties of shotcrete are very significant for determining suitable shotcrete design. Flow characteristics of the shotcrete must be determined for pumpability and fluidity of the material."

Jan 1, 2017

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson, Brian Somes, Kevin Wegman

"To perform a probabilistic risk assessment (PRA), a method of quantifying the risks associated withinfrequent high consequence events, consequence models that generate representative estimates of human health consequences for a wide variety of representative scenarios are commonly used. Criteria that suitable models must possess include: (1) input requirements necessary to generate large volumes ofprobabilistic simulations; (2) the capability to output injuries with the necessary details and resolution;(3) the ability to capture the variety of different scenarios inherent in an assessment; (4) acceptable cost and computational requirements; and (5) sufficient stakeholder buy-in for community acceptance."

Jan 1, 2017

By E. Bakhtavar, R. Mikaeil, D. Khademi

"Fuzzy-weighted integer goal programming has been developed and used to select the most suitable site to construct a central processing plant for several adjacent small-scale dimension stone quarries, based on the most effective criteria. In the first step of mathematical modelling, the most important goals and decision variables were defined. Accordingly, an objective function was used in the model for minimizing the sum of undesired fuzzy-weighted deviations. Fuzzy weights were determined by a matrix of pairwise comparisons of various expert judgments in this field and the fuzzy geometric mean. The goal and systemic constraints were also modelled. The most suitable site for the construction of the plant was selected after solving the mathematical model in the ExcelR Solver add-in. The selected site had various advantages over the other sites, such as the shortest average distance to the quarries, the shortest distance to power access and workforce, and the lowest land price. IntroductionSelection of the most suitable site of a plant is one of the most important considerations when constructing an industrial project. A suitable site has a significant effect on a company's competitiveness in the market. Selecting a desirable location for constructing plants such as mineral processing facilities is an essential part of the economic planning that will enable a company to meet the needs of related upstream and downstream operations. These units are considered to be best built near the relevant mining sites because of technical difficulties, the cost of transporting minerals, and the traffic hazard caused by the movement of trucks transporting materials. Two main types of research using multiattribute decision-making models have been reported for selection of a processing plant site (Safari et al. 2010, 2012). In that research, the analytic hierarchy process (AHP) and fuzzy technique for order preference by similarity to ideal solution (TOPSIS) approach were applied to select the suitable locations for the mineral processing plants for phases 1 and 2 of Sangan iron ore mine."

Jan 1, 2017

By M. L. Harris, J. Organiscak, S. Klima, I. E. Perera

"The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) conducted underground evaluations in an attempt to quantify respirable rock dust generation when using an untreated rock dust and a rock dust treated with an anti-caking additive. Using PDM 3600s and 3700s, these evaluations measured respirable rock dust levels arising from a flinger-type application of rock dust on rib and roof surfaces. Rock dust with a majority of the respirable component removed was also applied in NIOSH’s Bruceton Experimental Mine (BEM) using a bantam duster. The respirable dust measurements obtained downwind from both of these tests are presented and discussed. This testing did not measure miners’ exposure to respirable coal mine dust under acceptable mining practices, but indicates the need for effective continuous administrative controls to be exercised when rock dusting to minimize the measured amount of rock dust in the sampling device. INTRODUCTION Two factors have combined to renew concern regarding respirable dust measurements and compliance. This renewed recognition is due to two regulations that have modified operators’ rock dust schedules. First, the 80% incombustible requirement in intake entries has increased both on-section and outby-the-section rock dusting. Secondly, the recent respirable dust regulation change that has increased the number of respirable dust samples taken per sampling cycle. Previously, when only 5 samples were needed bi-monthly, rock dusting could be scheduled to not interfere with the respirable dust sampling schedule. The significant number of samples now required under new regulations combined with the need to maintain 80% total incombustible content in active mining areas require the schedules for respirable dust sampling and rock dusting to intermix. This raises concerns about the amount of rock dust that potentially is included in the sampler weight gain. Additionally, the respirable dust maximum was lowered from 2.0 mg/m3 to 1.5 mg/m3 (effective August 1, 2016) increasing concern that rock dust contamination may be an issue. Currently, the acceptable practice is to apply administrative controls such as keeping the miners upwind during rock dust application or to schedule rock dusting during a maintenance shift when the number of miners present is lower. NIOSH’s research examining the quality of rock dust has led to the development of hydrophobic rock dusts."

Jan 1, 2017

By M. Rylatt, E. Legault-Seguin, C. Mohns

"With energy costs increasing and ore grades diminishing, the role of preconcentration in hard-rock mining operations has gained greater interest. Dense medium separation is a process that can be conducted at particle sizes from 250 to 0.50 mm with high separation efficiency, depending on liberation characteristics of the valuable minerals. Pilot-plant case studies conducted at the SGS Lakefield site are presented, including mineral systems such as spodumene, sulfide-bearing gold ores, and complex sulfide ores. These case studies demonstrate that, for amenable ores, mass rejection of 20–60% is possible while maintaining recoveries of greater than 90%.RÉSUMÉ Au vu de la hausse des coûts liés à l’énergie et du déclin de la teneur des minerais, le rôle de la préconcentration dans les exploitations minières en roche dure présente un intérêt croissant. La séparation (ou concentration) en milieu dense est un processus pouvant être mené sur des calibres de grains de 250 à 0.50 mm avec un rendement élevé de séparation, en fonction des caractéristiques de libération des constituants des minéraux métallifères. Sont présentées dans cet article des études de cas menées dans des usines pilotes du site de Lakefield de SGS, lesquelles incluent des systèmes de minéraux tels que le spodumène, les minerais aurifères sulfurés et les minerais sulfurés complexes. Ces études de cas montrent que pour les minerais présentant les caractéristiques de libération appropriées, il est possible d’atteindre un rejet en masse de 20 à 60 %, tout en maintenant des récupérations supérieures à 90 %.INTRODUCTIONPreconcentration is the process of rejecting gangue minerals while ensuring recovery of valuable minerals prior to more intensive, downstream processing. Preconcentration has been practiced in the industry for many years, and is gaining greater interest as the industry copes with processing lower grade, more difficult ores, which typically require finer grind sizes and incur higher energy costs.The benefits of preconcentration are:• lower mining costs, which allows for nonselective mining;• lower process capital and operating costs (e.g., resulting from reduced grinding, flotation, and fines disposal stages);• increased ore reserves, which provides the potential to treat lower grade ore;• increased mine production without expansion of the existing plant or concentrator;• reduced overall tailings impoundment by converting the reject into a byproduct (e.g., underground backfill or aggregate);• improved efficiency of downstream processes (e.g., silica removal in electric arc furnace feed, removal of softer sliming minerals prior to grinding);• potential application to brownfield operations and greenfield projects; and• a “green” process option, which reduces processing energy consumption;– reduces mill feed;– increases stage metal recovery (higher grade feed);– increases mill metal output per tonne processed;– reduces surface plant, tailings dump, and tailings pond requirements because the plant has a small footprint and can be installed underground; and– can be applied to retreatment of old tailings dumps to recover metal values and reduce environmental impacts (e.g., dissolved metal runoff, acid drainage)."

Jan 1, 2017

"The Morris Island Lighthouse (MIL) is located between the jetties leading to the Charleston Harbor and Folly Beach, S.C. The present structure is the third lighthouse to occupy this location. The first navigational aid was erected in 1673, and consisted of a raised pan filled with pitch, which was set afire at night to guide early ships. The next structure was built in 1767, and constituted the first real lighthouse, standing 42 ft (12.8 m) in height. In 1838, a second lighthouse was built on the site, and it measured 102 ft (31 m) in height and featured a revolving light. This structure lasted until 1862 when Confederate troops, during the Civil War, destroyed it to deny its use to Union troops.Navigators steered these waters without a lighthouse for nearly a decade until 1876, when the current structure was built under the direction of the U.S. Army Corps of Engineers (USACE). In 1886, the Charleston area suffered a M7.6 earthquake. Significant damage was caused throughout much of the area, including a slight “list” of the lighthouse to the northeast. As a result, the cast of the beacon was reduced from 18 mi (29 km) to about 6 mi (9.7 km), causing much distress to navigators until the beacon platform was releveled and remains at this list to the present day.Conditions for ConcernThe current lighthouse was originally constructed about 1,200 ft (366 m) from the shoreline. Over the years, USACE has undertaken several programs to meet the increased shipping and navigation demands in the Charleston Harbor. Around the turn of the last century, two jetties were constructed, which drastically changed the approach direction for ships entering the harbor. In subsequent years, the harbor began to experience accelerated siltation."

Jan 1, 2017

By Y. Thibault, L. Morin, R. Cameron, D. Gould

"There are an estimated 50 to 100 million dry metric tonnes of low-grade nickeliferous pyrrhotite tailings in the Sudbury area alone, with an average nickel grade ~0.8% (plus cobalt). Pyrrhotite is a highly reactive sulphide mineral that has the potential to generate acidity; consequently, it is stored in large tailings ponds that require perpetual treatment to avoid the production of acidic drainage. Re-processing this material using bioleaching technologies has the potential to recover valuable metals, while reducing the toxicity, reactivity, and acid generating potential of the remaining residues. CanmetMINING is currently developing a stirred-tank bioleaching process to recovery nickel and cobalt from pyrrhotite-rich tailings. Stirred-tank experiments have been conducted with one tailings sample over a range of pH and temperature conditions, resulting in 80 to 90% and 70 to 80% leaching of nickel and cobalt respectively in 10 days.INTRODUCTION Sulphide tailings may represent a significant financial liability for mining companies as these wastes may produce acidic drainage under some disposal conditions. As a result, the companies must post financial bonds large enough to ensure there are sufficient funds for perpetual management of these wastes. At the same time, there are billions of dollars in metals incorporated into these mining wastes waiting to become valorized. Many sulphide tailings are amendable to bacterial oxidation for metal extraction. Re-processing of tailings using bacterial leaching has the potential to recover valuable metals from waste; and reduce the toxicity, the reactivity, and the acid generating potential of the remaining residue. By reprocessing these wastes there is an opportunity to significantly reduce liabilities and financial assurance bonds, while recovering metal values. There are an estimated 50 to 100 million dry metric tonnes of low-grade nickeliferous pyrrhotite-rich tailings in the Sudbury area alone with an average nickel grade ~0.8% (Peek et al., 2011) plus cobalt and copper. Pyrrhotite is separated from pentlandite concentrates by magnetic separation and flotation. It is already finely ground and has often been segregated from other tailings material, making „mining? relatively inexpensive. This represents roughly (> $100/ton) in contained value, with negligible mining costs. This paper reports on the development of a stirred-tank bioleaching process for recovering nickel and cobalt from pyrrhoitite-rich tailings, which is currently underway at Canmet MINING."

Jan 1, 2017

By Franz-Werner Gerressen

"The use of soil improvement to utilize areas, which are not suitable for foundation purpose, has a long tradition. Due to the increasing demand of foundation works in areas of unsuitable soils, the improvement of the existing soils becomes even more important in the future.Various applications and systems for various demands exist around the world. Either it is a “simple” improvement for settlement reduction or a more important aim as liquefaction mitigation. However, each system has its advantages, limits and needs.Furthermore to the soil improvement, using various tools, soil mixing can also be used for applications like cut off and/or retaining wall.The paper will describe some basics of various techniques and different applications of the systems all over the world where the systems provided solutions for different purposes, e.g. simple foundation or liquefaction mitigation.It will describe also the main equipment which will be needed to execute these works under the various conditionsINTRODUCTIONSoil mixing is a methodology where the soil is improved by mixing it with cement, lime or other binders in situ by using a mixing tool. This methodology can be used either as wet mixing or as dry mixing. In the more frequently used wet mixing process, usually a mixture of binder and water, maybe with additives, is injected and mixed with the soil. Depending on the type of soil and binder, by the end of the mixing process, a mortar like mixture is created which hardens during the hydration process. In the dry mixing process, the binder is directly mixed with the soil and reacts directly with the existing soil and water.Mixing tools show several versions, so that they are mixing around either a vertical or horizontal axis, mixing in a trench and maybe are jet assisted. Figure 1 shows a classification done by Bruce 2010. Depending on the technique, improvement depth of up to 80 m can be achieved."

Jan 1, 2017

By Valery M. Yubko

"The conceptual basis of the developed model is based on the ideas that evolution of geological-geomorphological structure of the CCZ is controlled by four types of geologic factors: geodynamic, sedimentary, volcano-tectonic and erosion-lithodynamic. In terms of time span two factors (geodynamic and sedimentary) can be considered as permanent and the other two as sporadic.The geodynamic factor is responsible for two interrelated geological processes. One is going under conditions of the axial zones of spreading centers and results in formation of the CCZ basement. Historically this process is considered as a starting point for each of the heterochronous fragments of the CCZ. The second one controls gradual shifting towards the Pacific Plate (Hawaiian direction) and subsidence to greater depths of the neogenic fragments (basement). Thus, those processes control basic topography, geomorphology and the seabed depth within the CCZ.Volcanogenic-hydrothermal activity of the EPR is one of the main sources of the ore components, which finally compose manganese nodules as a result of complicated processes of their dissemination and transportation to the bottom in dissolved and organically bound forms.The role of the other constant factor (sedimentary) is displayed in two ways. Firstly, initial relief is smoothed under the influence of this factor, which, subsequently, makes favorable conditions for manganese nodules formation. Secondly, it favors transportation of the majority of the ore components, participating in manganese nodules formation into zones of active nodules formation."

Jan 1, 2017

By D. Brand

"The risk management objective of the AMIRA Code of Practice for Metal Accounting has seldom been systematically investigated in the literature up to the authors’ knowledge. Risk is defined in the Australian Standard on Risk Management (AS/NZS 4360:2004), as “the chance of something happening that will have an impact on objectives”. The simplified economic analysis performed in this paper has lead to define “something happening” as measurement non-representativity and “impact on objectives” as NSR loss from the optimal NSR. This has pinpointed a missing link being the establishment of a relation between NSR in flotation plants and measurement representativity. The proposed framework, referred to as the total cost of representativity, answers the previously unanswered question of how much accuracy/reproducibility is fit for purpose in a given flotation plant. Authors readily acknowledge that it is way easier to assess the cost of accuracy/reproducibility than the cost of inaccuracy/irreproducibility. However, this exercise not only answers previously unanswered questions but also establishes an essential link with operational excellence. This paper exposes why such operational excellence could neither be attained nor proved without a state of the art metal accounting system. This should impact not only how metal accounting systems are audited/designed/refactored, but also how flotation plants are designed.IntroductionBecause representative metal accounting is a vital source of information for the financial accounts of a mining/metallurgical company, the need for a code on metal accounting was recognized in 2001 and a team was formed in 2003, under the sponsorship of several major mining houses, to produce such a code. Table 1 exposes the two main objectives of this AMIRA Code of Practice for Metal Accounting."

Jan 1, 2017

By M. Kumaran, A. Vetriselvan, A. Purantharan

"This paper presents a case history of evaluating the stability of a distressed earth bund and rectification measures carried out. A 5.45 km long, 7m high earth bund for drinking water storage was constructed in Andhra Pradesh. During construction of the bund following were observed – (a) a longitudinal crack at the downstream side (b) Bund on the downstream side along the crack settled to a max of 700 mm and (c) downstream rock toe level area raised by heave up to 175 mm. Investigation of the events made important contributions to the fundamental understanding of the behaviour of large earthworks of this type. It was found that the variation in subsoil strata was not addressed during the execution.After careful evaluation, stone columns were recommended as a suitable ground improvement technique. Stone columns were used as a reinforcement to improve the shearing resistance of foundation and in turn ensure stability. By using and applying advanced geotechnical engineering analysis tools and modelling techniques, earth bund and its foundation was analysed and examined against failure by slope instability. Stone column design was carried out using in-house computer program GEOSTONECOL and stability of earth bund was analysed using TALREN software. Earth bund construction was completed after ground improvement and is performing satisfactorily.INTRODUCTIONIn order to supply water during summer season, Government of Andhra Pradesh decided to construct a 7m high and 5.45km long earth bund summer storage tank. It was one of the largest earth bund summer storage tanks in whole of South India at the time of its construction. During construction, the earth bund has undergone sudden distresses. Investigation of the series of events occurred during construction has made important contributions to the fundamental understanding of the behaviour of large earthworks of this type. This paper presents the reasons for earth bund failure, slope stability assessment of the distressed earth bund and recommendation of stone column as a suitable ground improvement remediation technique.DESCRIPTION OF STUDY SITEThe characteristics of the original construction are briefly described as follows. A shallow cut-off trench was excavated below existing ground level at the centreline of bund as shown in Fig. 1. Below the base of the trench a cut-off grout curtain was installed. Upstream and downstream shell earth filling was carried out using Clayey Sand ‘SC’ type soil. At some locations, bottom of cut-off trench has reached as deep as 12m from the existing ground level."

Jan 1, 2017

By R. Holmwood, M. Faris, P. Holloway, M. Collins

Sulphuric acid addition is a major driver of the economics in the processing of nickel laterite ores by high pressure acid leaching (HPAL). Understanding the optimal acid addition rate is essential for the success of any HPAL operation, and this is especially true at Ambatovy, where the composition of the feed tends to vary significantly on a day-to-day basis. Most studies on the effect of acid on nickel extraction in HPAL have used laboratory testwork as their basis. Although these studies are invaluable in assessing the economics of a new project, they are limited by the range of ore composition that can be tested and the differences between the operation of the laboratory equipment and the commercial plant. To enable optimization of the acid addition at Ambatovy, operating data from the HPAL operation were obtained using OSISoft’s PI system and the data from several periods were examined to develop relationships between acid addition and nickel extraction. The initial relationships from 2014 focused on the acid required to achieve a target nickel extraction of 95%, with aluminum and magnesium in ore and feed slurry solids content as the major variables. As Ambatovy ramped up through 2015 and 2016, the calculated acid requirement was further refined to address the effects of HPAL temperature and retention time, and the oxidizing/reducing characteristics of the ore, and to generate acid requirement relationships as a function of ranges of nickel extraction. These relationships supported raising the target nickel extraction to 96% and enabled the development of an economic model between acid addition and nickel extraction.

Jan 1, 2017

By Lorena Blanco, Guillermo Gómez-Ramos, Iker Blasco, Egidio Marino, Luis Somoza, Ricardo León, Teresa Medialdea, Javier González

"This study presents the first catalogue of marine mineral deposits and energy resources along the continental margin of Spain. Aggregates, oil and gas and metalliferous mineral areas have been defined and mapped. The catalogue, implemented in a geographic information system (GIS), is conceived as a first national database within the European network, which is being built as part of the EMODnet-Geology project. It comprises 8 types of mineral and energy resources for the Spanish margins: aggregates, hydrocarbons, evaporites, placer deposits, phosphorites, polymetallic sulfides, polymetallic nodules and cobalt-rich ferromanganese crusts (Figures 1 and 2). The catalogue stores a total of 409 marine mineral deposits and compiles information such as name, deposit type, main morphology, main minerals, setting or area extent for each mineral deposit. By number of deposits compiled, the aggregates are the most abundant (286) followed by hydrocarbons (62), cobalt-rich ferromanganese crusts (32), evaporites (9), placer deposits (8), phosphorites (5), polymetallic nodules (4) and polymetallic sulphide deposits (3). Considering the total extension, hydrocarbons (32,386 km2) and cobalt-rich ferromanganese crusts (24,951 km2) represent the biggest areas.The Geological Survey of Spain (IGME) is developing a new tool in the catalogue, according the International Seabed Authority (ISA) Database parameters, for individual samples on each ferromanganese deposit. The database includes an extensive collection of records that comprise five information groups: general cruise and sample data, physical properties, mineralogy, geochemistry and acronyms used. New attributes have been incorporated, in example: geophysical, sedimentological and petrological data in the deposit area, sample weight, porosity, morphology, textural and structural features, geochemistry of major, minor and trace elements (included REEs and PGEs) and supplementary cruise and laboratory reports. This new database complements the EMODnet-Geology project minerals catalogue, offering a deeper level of information for the areas with major potential for mineral or energy resources as they are the Canary Island Seamount Province, the West Margin of Galicia and the Gulf of Cadiz."

Jan 1, 2017

By J. R. Schafler, J. L. Brinkman

"Since the year 2000, 59 miners have lost their lives to explosions occurring in underground coal mines in the US. More accurately, those explosions were methane ignitions that propagated through the mines due to coal dust involvement; despite current explosion prevention standards. There are 4 basic strategies employed to manage the risk of coal dust explosions in many other coal mining countries around the world: removal of the coal dust, wetting of the coal dust to prevent it from becoming airborne, mixing of the coal dust with stone dust to increase the total incombustible content, and explosion activated barriers which make the entire roadway inert. However, American standards only mandate the first 3 of these 4 methods. It is possible that US coal mine safety measures could benefit from the implementation of the 4th method, the use of explosion barriers. This paper will discuss differences/similarities in barrier regulations used in other countries, as well as some potential difficulties with adapting a stone dust bag barrier system to US underground coal mines. Also, details and feedback gathered from two operating mine site trial barrier installations will be shared.INTRODUCTION Since the year 2000, 59 miners have lost their lives to explosions occurring in underground coal mines in the United States (US); 29 miners were killed at the Upper Big Branch mine in 2010, 5 at the Darby Mine No. 1 in 2006, 12 at the Sago Mine also in 2006, and 13 at the Jim Walter No. 5 Mine in 2001.[14] To be more accurate, the explosions that killed those miners were methane ignitions that propagated through the mines due to coal dust involvement.[18, 19, 20, 21] These deaths occurred despite current explosion prevention strategies, standards, and regulatory oversight. This poses the question, can more be done in the US to prevent coal dust explosions and their widespread damage. In review of current practices and regulations from several large coal mining countries, a disparity in prevention strategies arose. The main difference between the US and other countries was that the US does not encourage, mandate, or regulate the use of explosion barrier systems as an additional coal dust explosion mitigation measure. This raised many questions. First and foremost was whether or not the US coal mining industry and its miners could benefit, in terms of safety and fatality prevention, from the implementation of the explosion barrier systems that are used in other countries. Furthermore, are there significant differences between the coal mines in countries where explosion barriers are used and US coal mines, which would preclude the system from being adapted and implemented in the US? Also, what are the similarities and differences in explosion barrier systems, use, and regulations between other countries that use them?"

Jan 1, 2017

By Y. Qin, X. Fu, T. Qi, H. Tang

"The FASTMELT ® process was developed as an alternative to blast furnace ironmaking; in this process, high-quality molten iron is produced using direct reduction followed by high-temperature slag/metal separation. In this study, iron recovery and phosphorus removal from oolitic highphosphorus haematite using the FASTMELT® process was investigated. The performance of two reducing agents, coal and wood char, was compared. Direct reduction experiments indicated that with optimized reductant addition, the ore-char and ore-coal briquettes attained metallization values of 82% and 78%, respectively, and residual carbon contents of 0.24 and 2.35%, respectively. The slag/metal separation experiments revealed that molten iron containing 0.41% phosphorus and 0.021% silicon (by mass) was produced from optimally reduced ore-char briquettes, and molten iron containing 0.78% phosphorus and 0.91% silicon from optimally reduced ore–coal briquettes. The study indicates that carbonaceous materials with high CO2 reactivity are suitable for use in the FASTMELT ® process for phosphorus removal and iron recovery from oolitic high-phosphorus haematite. IntroductionIn China, the general depletion of iron-rich mineral reserves has led to many efforts to exploit low-grade and refractory ironcontaining resources for ironmaking (Liu et al., 2014). The efficient utilization of the highphosphorus oolitic haematite resources in central China has received considerable attention. The available resources of this material total approximately 3.0 billion tons. The oolitic units in the ore exhibit an onionlike structure with phosphorus-containing gangue layers of 2–10 µm thickness. The best concentrate produced from these resources contains approximately 50% iron (Fe) and 0.8–1.2% phosphorus (P) (by mass) (Ai, Yu, and Wei, 2009; Song et al., 2013; Wu, Wen, and Cen, 2011). Further removal of phosphorus from these ores using conventional beneficiation methods is not possible."

Jan 1, 2017

By Eric J. Grimsey, Don C. Ibana, David E. Grimsey

The segregation process as applied to nickel laterite ores involves the formation of gaseous nickel and iron chlorides which are subsequently reduced to form ferronickel on the surface of a solid carbon reductant. A fundamental study of the process has been carried out using limonite, nontronite and garnierite ores. The study highlighted the significant impacts that ore mineralogy and carbon addition have on the amount of nickel which is segregated rather than retained within the ore due to in-situ reduction. These important aspects affecting nickel recovery and the success of the process are discussed in this paper.

Jan 1, 2017

By Glenn J. Rix, Eduardo Tavera, Raphael Siebenmann, Zhongjie Zhang, Robert C. Bachus, Jongwon Jung

"The Louisiana Department of Transportation and Development (LADOTD) uses a variation of the FHWA-modified Gates equation to verify the nominal pile bearing resistance, typically on smaller projects where static load tests and dynamic monitoring are not practical. An inconsistency in the resistance factors for load and resistance factor design (LRFD) penalizes the target pile capacity needed during field observation if the LADOTD dynamic formula equation is used, which is unreasonable, and has created confusion among designers, consultants, district personnel, and inspectors in Louisiana. The objectives of this project are to recalibrate the FHWA-modified Gates equation and update the associated LRFD resistance factor for pile types and local soil conditions encountered in Louisiana. Improved consistency relative to the current design approaches will be achieved if the updated resistance factor matches or exceeds the worst-case resistance factor used by LADOTD, which will reduce confusion among users. Updating the resistance factor will also serve to increase confidence in the FHWA modified Gates equation, optimize the efficiency of the piles, and reduce project costs.IntroductionThe original 1957 Gates pile driving formula (Gates, 1957) is an empirically derived dynamic formula that is used to predict pile capacity in the field during pile installation. The original Gates formula tends to over-predict pile capacity for low driving resistances and under-predict pile capacity for high driving resistances (Hannigan et al., 1998). Thus, the Federal Highway Administration (FHWA) proposed a modified version of the Gates formula that addressed this limitation. The FHWA–modified Gates equation is:"

Jan 1, 2017

By Dave Rose, Jacques McMullen

"The Detour Lake mine is located 200 km northeast of Timmins, Ontario, Canada.The mill processes a free milling gold ore using both a gravity circuit and leaching with a state-of-the-art carbon-in-pulp circuit. The grinding circuit is a conventional SABC circuit with a tonnage of 55,000 tpd at 95 microns with the addition of pre-crushing upstream of the SAG mill.The Detour Lake mine has one of the largest gyratory crusher in the world (60"" x 113"") and over the years, many improvements have been made to this crusher with the result of improving plant throughput. This paper will present how choke feeding the gyratory crusher has been found to be one of the main influences on crusher product particle size and plant throughput. It will explain how the effect of choke feeding the gyratory was measured and from that, the various changes made to improve choke feeding of the gyratory crusher.IntroductionOre is hauled from the open pit mine and dumped directly into a single 60"" x 113"" primary gyratory crusher. The live capacity of both the feed and discharge hoppers of the gyratory crusher are designed for two (2) truck loads each, assuming a nominal payload of 300 tonnes per truck. The surge bin under the primary crusher feeds an apron feeder that controls the ore feed rate at approximately 4,200 tph onto a 227 metres long x 1.52 metres wide belt conveyor with a nominal capacity of 4,200 tph.The primary crusher is operated at an open side setting of 172 millimetres to produce a F80 feed to the secondary crushing circuit of 135 millimetres."

Jan 1, 2017

By Baohua Guo, Xuelin Yang, Tingkan Lu, Hailin Sun

The work presented in this paper mainly involves two parts. Firstly, the fundamental characteristics of the high pressure carbon dioxide gas fracturing technique (CO2 technique), including, a proposed method of TNT equivalence calculation, which is used to calculate the TNT equivalence of discharge of CO2 technique, and the comparison of the explosion volume generated by dynamite and expansion volume of liquid carbon dioxide is conducted to show the differences of fragmentation capacity between the two of them. Secondly, the coal seam fragmentation mechanisms of CO2 technique are proposed, including, 1) Gas jet cutting and penetration by shaped charge, 2) Gas volume expansion by changing phases of carbon dioxide, 3) Coal seam softening by destress blasting and 4) Coal seam fragmentation by discharge vibration, associating with the mechanisms, the equations for calculating fragmentation radius are developed and verified.

Jan 1, 2017