Search Documents

By E. McCullough, S. Gaillard

"Diesel particulate matter (DPM) has been regulated by the U.S. Mine Safety and Health Administration since 2002 in underground metal and nonmetal mines. To demonstrate regulatory compliance, DPM samples must be collected and later analyzed by the U.S. National Institute for Occupational Safety and Health (NIOSH) 5040 standard method, but the FLIR Airtec DPM monitor can serve as a complementary engineering tool. The monitor is a handheld instrument that offers near-real-time measurements of elemental carbon (EC), which is a primary constituent of DPM. As part of an ongoing field study, the monitor was used to survey EC in an underground stone mine. This effort was aimed at determining spatial and temporal DPM variations in several key locations. The results of prolonged area monitoring—that is, lasting several hours — revealed that DPM concentrations were diluted substantially as air moved away from the primary production zone, but that concentrations could vary quite a bit in a single location from day to day and between seasons. DPM concentrations were generally lower in winter than in summer, which is consistent with increased natural ventilation airflows during winter. Using a modified sampling cassette, an attempt was also made to sensitize the Airtec monitor to allow for “spot-checking” of EC concentrations — that is, measurements made in several minutes. Preliminary field data showed that the sensitive cassette performed well in terms of providing accurate data that could be useful for rapid assessment of DPM. IntroductionDiesel particulate matter (DPM) is the solid fraction of the exhaust emissions from a diesel engine. It largely consists of elemental carbon (EC) and organic carbon (OC) (Birch, 2003). The World Health Organization International Agency for Research on Cancer classified diesel exhaust, including DPM, as a carcinogen (World Health Organization, 2012). It is believed to cause and/or exacerbate respiratory illness upon inhalation, deposition and retention in lung tissue. Because DPM exists in both the micro- and nanoparticulate ranges, it can bypass typical autoimmune defense mechanisms that keep larger particles out of the respiratory system (Ristovski et al., 2012)."

Dec 1, 2016

By Amado Yataco

"El presente texto describe una aproximación sobre la producción de los ocho metales -en tanto determina el Producto Bruto Interno durante el período 2016 en el Perú. Los metales considerados son: cobre, oro, zinc, plata, molibdeno, plomo, hierro y estaño. Asimismo, se muestran cuadros gráficos de la producción de los años 2012 y 2015 para tener series de producción reales y las mejores estimadas del 2016 y 2017. Finalmente se presenta la evolución del PBI en Cerro Verde, Las Bambas y Antamina. "

Dec 1, 2016

By Iván Zevallos

"La mina de talco localizada en el estado de Río Grande del Sur (Brasil) fue explotada hasta agotar sus reservas. En ese sentido, para descartar la existencia de algún cuerpo del mismo mineral en las proximidades se propuso efectuar una prospección magnética terrestre. La asociación del talco con esquistos magnesianos y serpentinitas confiere validez al levantamiento geofísico, debido a la alteración de los esquistos que los torna ferromagnéticos, de forma que se determina que el yacimiento fue explotado. En ese sentido, el presente texto describe el levantamiento magnetométrico como método magnético para determinar el cierre de una mina de talco como importante precedente para los exploradores de yacimientos de minerales no-metálicos."

Dec 1, 2016

"There is no fast way to add more than 6.4 km (4 miles) of track, most of it underground, to the Sound Transit Link Light Rail system in the Seattle, WA area. But increasingly busy traffic through a number of neighborhoods made it necessary. That’s the challenge a joint venture of several tunneling contractors faced when starting its portion of the $1.9-billion Northgate Link Extension in 2013, and the project is still keeping it busy three years later. Completion will mean just a 14-minute ride from Northgate to downtown for an extra 60,000 passengers by 2030. The transit lines will join 57 km (36 miles) of new and under-construction light rail lines running north, east and south from Seattle.Voters tired of long commute times approved the project, a key part of Seattle’s regional mass transit system, in 2008. The extension is part of a plan adopted by the Sound Transit board in 1996 to connect the region’s major activity centers. The Northgate project is meant to relieve one of the area’s most congested traffic areas by connecting the Northgate, Roosevelt and University District neighborhoods to existing routes including downtown Seattle and SeaTac airport.Sound Transit dedicated more than a quarter of the project’s estimated expense — $440 million -— to general contractor JCM Northlink LLC to handle the tunnel segment. JCM is a joint venture formed in 2013 between Jay Dee Contractors of Livonia, MI, Frank Coluccio Construction of Seattle, WA and Michels Corp. of Brownsville, WI. The contractors regularly collaborate on large-scale projects and brought experience working on a different section of the extension they completed in 2013.JCM project leaders knew immediately that the schedule would be demanding. They had to work around the clock six days a week to meet deadlines. The extension runs through highly populated areas, meaning contractors had to follow strict city noise restrictions between 10 p.m. and 7 a.m. Plus, supervisors needed to manage the scheduling of nearly 250 employees to keep work running smoothly.“We had eight different operations and four different subcontractors trying to work in one tunnel,” said Chris Wood, JCM site project superintendent. “It’s important that we keep work linear. That’s the biggest challenge: keeping a path in and out so you can pour concrete, keep electricians and carpenters going, and accomplish everything else.”"

Dec 1, 2016

By Michael Gobla

"Since 1994 the Bureau of Reclamation (BOR) has used risk analysis to evaluate dams. Risk considers both the likelihood of failure and the expected consequences should failure occur. Risk analysis relies on the detailed formulation and critical analysis of all possible potential failure modes. Potential failure modes are formulated by describing the sequence of events that must occur to result in failure, where failure is defined as the uncontrolled release of the impounded reservoir. Failure occurs in response to loadings such as water seepage through a dam (static forces), shaking from an earthquake (dynamic forces), sudden flood inflows (hydrologic forces), or accidental overfilling (operational errors). Reclamation has, to a limited extent, applied risk analysis to inactive and abandoned mines to evaluate tailings dams, pit lakes and flooded underground mines. Case histories of potential failure mode analysis, as applied to mine impounded water, illustrate what critical technical information is needed to determine if failure is likely, what the consequences of failure are likely to be, and what are the highest risks that should be addressed first.IntroductionImpounded water and high water content wastes at mining and industrial processing sites are potential threats to public safety and the environment. Recent failures such as the TVA Kingston flyash impoundment failure in Tennessee in 2008 (4.1 million m3 or 5.4 million cu yd) release, the Mt. Poly Tailings Dam failure in British Columbia in 2014 (4.4 million m3 or 5.8 million cu yd) release, and the Samarco Fundao Tailings Dam failure in Brazil in 2015 (59 millon m3 or 78 million cu yd) release have renewed attention to this issue. Potential risks from impounded water at mining and industrial sites originate not only from tailing dams, but also from water in process ponds and conveyance pipelines, sediment retention dams, water retention dams, mine pit lakes and flooded underground mine workings.Conventional water retaining dams also have a record of failure. Notable examples of failure include Vajont Dam in Italy in 1963 (2,600 lives lost), Banqiao and Shimantan Dams in China in 1975 (171,000 lives lost), and Machhu-II Dam in India (10,000 lives lost). After the 1976 Teton Dam failure in Idaho, the U.S. Bureau of Reclamation (BOR) established a Dam Safety Program. By 1984, the agency developed and began using risk analysis methods. BOR operates and maintains an inventory of hundreds of aging dams which were designed and constructed over a period of 100 years. Many of these facilities were designed and constructed prior to the development and adaptation of modern soil mechanics in dam engineering. Diligent observational monitoring, detailed site investigations and the application of risk evaluation to the BOR dam inventory has identified many deficiencies resulting in significant demands on available funding for remediation efforts. The application of risk analysis has allowed the agency to rank sites by risk. By giving priority of remedial efforts to high-risk sites, significant improvements to dam safety have been achieved."

Dec 1, 2016

By William Gleason

"Speakers and attendees of the 2016 Cutting Edge Conference could not be faulted for keeping one eye on the presentations taking place at the Hyatt Regency at LAX in Los Angeles, CA on Nov. 7 and 8 and another on the results of the historic election in the United States that took place on Nov 8. While there was certainly interest in the presidential campaign, there was also a great deal of interest in Measure M on the California ballot. Measure M, which passed easily, is a half-cent sales tax increase that will fund the most ambitious transit expansion in Los Angeles County history.In the coming years, the ballot measure will transform a traffic-choked region by funding the construction of nearly a dozen new rail lines with an estimated $120 billion raised in four decades. Among the projects that could come to fruition are a twin-rail tunnels project through the Sepulveda Pass and new connections in the city.During the update on West Coast projects, Bill Hansmire summed things up with a slide asking “How much work is there on the West Coast,” and his answer was “Billions.”From Seattle, WA south to Los Angeles, there is already a lot of work for tunneling and underground construction experts, and Measure M ensures that there will be plenty of work for decades to come.Currently, The Los Angeles County Metropolitan Transportation Authority (Metro) has three rail projects underway that were funded by Measure R in 2008 — the Regional Connector, the Purple Line subway extension and the Crenshaw/LAX Line that are designed to alleviate the traffic pressure with an eye to more solutions.Measure M is the fourth sales tax increase to fund transportation in L.A. County, bringing the base sales tax rate to 9.25 percent. In some cities, which already levy their own sales tax, the rate would be higher, The Los Angeles Times reported.About 35 percent of the revenue will fund major new transit projects, such as the subway under the Sepulveda Pass, extension of the Gold Line to Claremont, extension of the Crenshaw Line to West Hollywood and acceleration of the Purple Line Subway construction along Wilshire Boulevard to finish in 2024, 10 years earlier than scheduled.About 17 percent would fund a dozen highway improvement projects, such as widening parts of I-5 in the Antelope Valley and southeastern county, adding bus lanes to the Sepulveda Pass section of the 405 freeway and adding truck-only lanes to a section of the 710 freeway."

Dec 1, 2016

By Z Fu, E Topal, O Erten

"Mine waste rock management involving waste rock movement and placement, is a critical aspect in the planning of open pit mining operations, as the waste rock haulage cost can be the largest portion of the mine operating cost. The concept of sustainable development in the mining industry also encourages environmentally friendly waste dumps that have zero hazards to people and the surrounding environment. Therefore, a detailed waste management schedule must satisfy economic and environmental considerations. However, the available tools in the market cannot provide optimal waste dumping schedules to meet all these constraints. This paper introduces a user-friendly and automatic tool to optimise the waste dumping schedule, which minimises the haulage cost, and covers the encapsulation of reactive materials to minimise acid mine drainage problems. This tool has been developed by using a new mixed integer programming (MIP) mathematical model that considers both single-lift and multilift dumping scenarios. The application of the proposed tool on a data set collected from a gold mine shows that the multilift dumping scenario has provided a more flexible and economical waste dumping schedule than the single-lift scenario, and both scenarios satisfy environmental requirements.Citation:Fu, Z, Topal, E and Erten, O, 2016. A Modified Software Tool for Mine Waste Rock Dump Planning, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 229–242 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By P Moynagh

"A plan is critical but on its own it is a bit one dimensional, the three dimensions critical to success over the long-term, through changing economic, geological and management conditions are:the quality of your planning an ability to see and adapt to change a disciplined continual improvement/learning system.This paper will examine how a number of major Australian resource companies have used a commitment management system to connect the ‘theory’ embodied in plans (whether mine, project, maintenance or training plans) and immediate reality ‘practice’ as experienced by supervisors and their crews in the workplace. This paper draws on management theory embodied in management operating systems (MOS), Lean, Theory of Constraints and Six Sigma approaches to continuous improvement and a good dose of real world experience. It is embodied in the statement: ‘successful organisations are driven by a series of commitments that people make to each other and deliver on’.Citation:Moynagh, P, 2016. Everyone Has a Plan Until They Get Punched in the Mouth – Creating Trust, Commitment and Results in Tough Times, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 293–299 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By R Thompson, D Tulloch

"Wet-weather or 24×7 wet-trafficability is a commendable design objective for unpaved mine haul roads, but practically often difficult to achieve, due both to the road sheeting material selected, and also its breakdown under the action of traffic and environment. Accidents allied to wet-trafficability issues, either due to rain or often more commonly, over-watering of mine roads, is increasing and especially the loss of control or uncontrolled vehicle movements categorisation. The dominant system failure is that once vehicle control is lost, control cannot be regained.The friction supply, or ‘skid resistance’ of a mine haul road sheeting is critical to the safe operation of the road and data has to be collated concerning the variation of friction supply with sheeting material engineering or indicator properties. In the light of the paucity of data existing in this field, this paper presents the contributory research that informs the development of improved and validated unpaved mine road friction supply estimates, based on a number of mine site evaluations across a range of sheeting material types and characteristic parameters, leading to improved predictive models of friction supply.Results from this preliminary review will enable operators to assess their road sheeting materials, improve and validate unpaved mine road friction supply estimates. This will contribute to improved road design, management and 24×7 operability decisions and contribute to a reduction in heavy vehicle loss of control incidents on gravel-surfaced mine haulage roads.Citation:Thompson, R and Tulloch, D, 2016. What's Stopping You? The Role of Sheeting Material Selection in Safe Haulage Operations, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 253–264 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By D Morton, G Wallace

"Evolution Mining is the sole owner of the Mt Rawdon open cut operation, located 75 km south-west of Bundaberg in Queensland, Australia (Figure 1). It is a massive, volcanically hosted, low-grade gold deposit that exhibits excellent characteristics conducive to low cost mining and treatment.In 2014, Mt Rawdon began investigating initiatives to deliver higher mill throughputs without any significant capital expenditure or modifications to the existing processing plant. Various studies have shown throughput increases are possible by applying more blast energy, essentially by reducing feed size through blasting and leaving less work for the comminution circuits (Brent et al, 2013; Ziemski, 2011; Workman and Eloranta, 2003).Given that 53 per cent of energy used on a mine site is consumed by the comminution circuit, with only two per cent being consumed by drill and blast (Smith, 2013), it makes logical sense for a mining operation to align their drill and blast with their processing plant. The term commonly used when exploring this relationship is a ‘Mine to Mill’ program.Over nearly 12 months, various blasting options and Mine to Mill methodologies were tested at Mt Rawdon. Throughout the journey, it was abundantly clear that the Mine to Mill initiative is not as simple as making one technical or physical change and expecting an improvement. Rather, true sustainable improvements demand a paradigm shift across both the mining and processing cultures, where all departments are aligned and working towards the one outcome. This true overarching Mine to Mill mentality, enabled by Vistis™ 250 high energy bulk explosive, ultimately led to a sustained increase in throughput and profitability of the Mt Rawdon operation.Citation:Wallace, G and Morton, D, 2016. High Energy Bulk Explosives and Mine to Mill Focus – the Mt Rawdon Story, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 60–69 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By D Kavanagh, C Michaud

"A continuous improvement initiative was identified at Kalgoorlie Consolidated Gold Mine’s (KCGM) Fimiston open pit with the goal of reducing bench turnover time and increasing shovel digability by improving fragmentation around previously mined-out stopes. In the past, a higher number of blasts than normal would be required to get through a single excavation area where stopes were present. This is due to the limited reach capability of the drilling fleet from safe ground into restricted areas requiring the drilling of the shot to be done in a staged manner. In addition, the holes that were able to be drilled in the area did not remain open long enough to be loaded with explosives as a result of the poor ground conditions surrounding the stopes.Over the last 18 months, KCGM has trialled drill additives to improve blasthole stability, as well as introducing a remote drill rig allowing holes to be drilled in areas previously inaccessible by manned drill rigs. This has resulted in improved penetration rates in bad ground conditions, improved drill hole stability, better shovel digability, and an overall reduction in bench turnover of at least ten days on the benchmarked 126 days average per bench. KCGM is now in the final stages of the improvement project with the installation of a drill monitoring system on the fleet to allow live data transfer back to the office for analysis, as well as providing improved accuracy on drill holes in restricted areas.Citation:Michaud, C and Kavanagh, D, 2016. Reducing Bench Turnover Time and Improving Shovel Digability, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 19–27 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By R Price

"Technology has the potential to revolutionise industries, work functions or businesses. One such technology in the mining industry is the deployment of automation in a modern autonomous haulage system (AHS). This paper examines a theoretical application of an AHS in a medium scale mine site. The cost-benefit commercial argument is particularly compelling, and the paper outlines metrics and future issues for consideration.Citation:Price, R, 2016. Autonomous Haulage Systems - the Business Case, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 11–17 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By R Price, B H. Miller

"The rise of autonomous haul truck fleets may have been initially driven by the rapid escalation of the cost of equipment operators, but the actual improvements reported by the major iron ore miners far exceeds the simple reduction in workforce. Utilising cost models developed for feasibility studies and mining contract modelling, the limits of cost improvements due to simple labour reductions are compared to those achieved by the early autonomous fleet adopters and through traditional process improvement techniques such as fleet class upgrades or hot-seating of equipment. As autonomous fleet implementation matures, it is likely that the gains seen by current adopters will seem minor compared to the limits generally governed by the limit of equipment utilisation. This ultimate limit is explored through time utilisation models, which were also developed for use in feasibility studies and mining contract modelling.Citation:Miller, B H and Price, R, 2016. Autonomous Haul System Savings - It's Not about Less Truckies but Better Truckies!, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 2–10 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By J Darbritz

"This paper details the events leading up to a slope failure that occurred at Kalgoorlie Consolidated Gold Mines (KCGM) and the remediation method executed using rope access specialists.n January 2016, KCGM Fimiston Pit experienced a double bench wall failure where approximately 80 000 t of material fell from the wall that blocked access to a ramp and caused minor damage to equipment.The event was triggered by heavy rainfall and occurred along unfavourable eastward dipping structures that lead into weaker shale/porphyry bands, which in turn left more material on the face. A remediation plan was formulated that would allow for the continuation of open pit operations while a full geotechnical assessment of the failure area could be conducted. This was accomplished by means of rope access specialists who abseiled down the wall and blasted off the remaining overhang using a portable drill rig and prepackaged explosives.This paper provides a brief overview of the KCGM operations, how the instability was identified and monitored, details of the failure event, outcomes of the geotechnical assessment and details on the remediation work.Citation:Graf, C and Sullivan, R, 2016. The Journey to Steepening the Pit Slope Angle - Advancing the Effectiveness of Wall Control, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 104–114 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By R Thompson, J Miedecke, D Handel, E Tomicek, D Tulloch

"The Mine Haul Road Optimisation Alliance (HROA) is a unique Australian industry–academia collaboration that has been developed to support mine haul road operators. The alliance integrates industry, end-user service providers and academic research expertise in mine haul road design, construction and operation to identify, quantify, implement and monitor the various equipment, materials and road management strategies and solutions required to drive haulage productivity improvements.Initially, a broad overview of the university–industry collaborative landscape is presented, following which the current situation in the Australian mining sector is reviewed both nationally, and on a country-wide basis internationally. This insight places into context the opportunity that strategic collaborations present, to drive productivity and efficiency in mining, while also delivering innovative technology solutions.Following an overview of the HROA collaborative structure, aims and objectives, it is shown how academia and industry collaborations can deliver a more robust and needs-driven solution to mine haul road design, performance and management, especially where integrated solutions are needed. Critically in this approach, implementation and monitoring data provided by industry and service providers alike form the foundation on which to develop research knowledge and innovation that is more responsive to the end-user requirements, typically represented by ‘early goals’ and practical, implementable solutions.The paper concludes with examples of how the alliance collaborations work in practice to deliver focused mine haul road research outcomes, together with the mechanisms used to ensure industry needs are met through end-user driven research solutions for enhanced operational performance.Citation:Handel, D, Miedecke, J, Thompson, R, Tomicek, E and Tulloch, D, 2016. Driving Haulage Productivity Improvements through Industry–Academia Collaboration, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 243–252 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By A K. Ghosh, J Chung, E Topal, M Asad

"Many open pit (OP) mines with considerable vertical extent are approaching the end of their life-of-mine; some of them are seeking the opportunity to make the transition from OP to underground (UG) mining. The decision on the best location for transition from OP to UG mining should be addressed at the strategic mine planning stage. Conservatively, the transition to UG mining is considered near or after the exhaustion of the reserve within the ultimate pit.However, if UG is evident and exclusively viable from the inception, defining the best location for the transition through a conservative approach may not be an optimal option to explore. This clearly establishes the need for a mathematical model that aims to maximise the project value and considers OP and UG mining with crown pillar (CP) requirement simultaneously. Underground mine layout varies from one UG mining method to the other, and consequently the variation in the location of transition is eminent. Thus, focus on the selection of UG mining method must be a part of this analysisThis paper presents an implementation of an integer programming (IP) based mathematical model that evaluates the changes in mining layout and the project value under possible variation in the transition point from OP to UG mining for stoping and block caving methods. An IP problem is a mathematical optimisation or feasibility method in which some or all of the variables are restricted to be integers. The outcome of the implementation reflects that mining strategies with OP transition to stoping and block caving methods generated higher values than OP-only mining strategy. The case study not only demonstrates the difference in mining layout for both stoping method and block caving method, but also reflects that a joint consideration of OP mining, UG mining and CP placement helps to achieve maximum project value and resource utilisation.Citation:Darbritz, J, 2016. Remediation of Wall Failure at Kalgoorlie Consolidated Gold Mines' Golden Pike Cut-back 2016, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 96–103 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By K Sommerville, J Parkinson

"Open pit mines today have more technology and data available. The challenge is to effectively use resources to analyse and identify mine productivity improvements. AMC Consultants Pty Ltd (AMC) has completed more than 100 benchmarking studies worldwide. In the process of gathering cost and productivity data, insights have been gained on how mines are using data to drive productivity. This paper aims to share good practice on using data, what benchmarks operations should be aiming for, where mines are currently sitting, high value areas to target, and how to best prioritise improvement to meet operational goals.A key purpose of data is to assist in managing and improving operations. Key information is used to drive meetings, decisions, budget estimates and reports. Safety, equipment productivity, available stocks, grade and spatial reconciliation are examples of where data is important for management systems. The key is to keep reporting simple whilst maintaining access to source data for troubleshooting and analysis.Some operations still have paper-based reporting systems. Some operations collect data directly off machines and instruments, use cameras and have off-site control centres. The level of technology is a fit-for-purpose choice.Comparisons of productivity assumptions commonly used in feasibility studies with good practice productivity numbers sourced from AMC’s benchmarking database will be shared in this paper. A typical activity mining cost breakdown will highlight where the high value areas for productivity improvement sit.In addition to examining the productivity of each mining step it is also important to examine the impact on the mine plan. Equipment numbers, strip ratio, grade and material hardness can impact the results of bottleneck analysis. A bottleneck example case study will highlight how productivity and other factors can be used to identify and prioritise improvement opportunities.Keep it simple. Use only the critical data for meetings, decision-making, reports and plans. Knowing and communicating the key performance indicators (KPIs) you are striving for aligns the operation and prioritises improvement plans.Citation:Parkinson, J and Sommerville, K, 2016. Getting the Most Out of Technology to Drive Mine Productivity Improvements, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 84–93 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By R Jaine, D Strang, M Fowler

"This paper presents a case study demonstrating active geotechnical pit slope management at the now completed Carina Iron Ore Project operated by Mineral Resources Ltd (MRL). The site is located 105 km north-east of Southern Cross, Western Australia. The paper is primarily focused on the slope stability failure modes and the remedial measures employed to maintain mining.Between a quarter and a third of the excavated slopes were impacted by some form of instability that was beyond expectations of the intended slope design criteria and common practice. Ongoing mining was supported by intensive geotechnical pit slope management including close cooperation between geotechnical, mine planning and operations staff to achieve timely and practical mining solutions.Mining encountered varied slope failure mechanisms which required a combination of remedial solutions comprising: horizontal depressurisation holes, deferral of excavation, unloading, buttressing and catch berms.The root cause of the challenging slope performance was a mismatch between the predicted and encountered geotechnical model, resulting from a failure to recognise the critical mechanisms that control slope stability.Despite the extensive zones of instabilities at completion of mining, full ore recovery was achieved without major delays and in a controlled and safe manner.Citation:Fowler, M, Strang, D and Jaine, R, 2016. Adapting to Geotechnical Change - a Case Study of the Carina Open Pit Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 150–161 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By J Rock, K Bambrook

"Hanwha Mining Services was approached by Glencore Coal to provide a series of (trial) demonstration blasts at its Clermont coalmine. The intent of the project was to trial a bulk explosive product that would be able to provide sufficient energy for the ground type encountered without production of post-blast fume. Three blasts were loaded using the patented XLOAD bulk explosives with a density of 1.00 g/cc. XLOAD bulk products are water resistant explosives that can be loaded at densities much lower than traditional (generic) water resistant heavy ammonium nitrate – fuel oil (ANFO) or pumped blends with significantly reduced risk of fume. In addition, these products have detonation characteristics that generally deliver a higher heave partition than conventional bulk products and hence improve muck pile looseness and digability.The priority key performance measures included the absence of fume from blasting, being at least cost neutral and providing similar if not improved shovel dig rates. The design for the initial blast took a conservative approach to ensure the key blast outcomes of fume control and fragmentation were achieved.The second blast used the same pattern dimensions as the benchmark bulk product used in this area to provide a cost neutral comparison with the benchmark products that had been used over the prior six months. This resulted in a 20 per cent lower powder factor than would have otherwise been used. To test the suitability of XLOAD, this shot was slept for over two weeks between loading and firing in geology where the sleep time is typically kept to a few days to minimise the fume risk.The third blast utilised a slightly larger drill pattern to push the capabilities of XLOAD and provide a cost neutral comparison between the trial product and the traditional benchmark products. All three blasts were fired with no fume observed, no recordable incidents and good fragmentation. Shovel productivity from all three of the trial blasts was excellent with higher average instantaneous dig rates being recorded (average six per cent improvement against the instantaneous dig rates recorded for the benchmark blasts).Citation:Rock, J and Bambrook, K, 2016. Controlling Blast Related Fumes with Unconventional Explosives, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 39–49 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By C Mann, S Swapp

"The mining industry is often challenged with the task of evaluating narrow vein open pit deposits. A realistic mineable solution from optimisation needs to accurately represent mining dilution and the practical limitations of mining equipment. Open pit dilution is driven according to mining method and fleet selection as this dictates the ‘selective mining unit’ (SMU) that can be practicably mined.Common evaluation methods represent dilution by:a mathematical dilution assumption addition of a dilution skin reblocking of the model to an appropriate SMU.This paper will explore an alternative method of applying dilution by adapting an underground stope modelling tool. By considering an SMU as a stope, automatic stope shape creators such as Datamine’s Mineable Shape Optimiser (MSO) can be used to create wireframes for each mining unit over the entire deposit. Using these wireframes, the model can be subblocked and assigned as either ore (inside the wireframe) or waste (outside the wireframe) prior to optimisation.The MSO process considers SMU geometry and a depth specific value-based cut-off. The result is an optimised solution for the deposit based on practical and achievable mining constraints rather than one based on generalised modifying factors.To evaluate the economic impact of the methods above, results have been costed and scheduled and a comparison of operating cash flows made.Citation:Swapp, S and Mann, C, 2016. Optimisation Improvements for Narrow Vein Open Pit Deposits Using Mineable Shape Optimiser, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 50–59 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016