Search Documents

By G Harbort, D Zoetbrood

"The Phu Kham copper-gold operation in the Laos People’s Democratic Republic (PDR) is owned and operated by Phu Bia Mining Limited. PanAust Limited holds a 90 per cent interest in Phu Bia Mining Limited, with the remaining ten per cent held by the Laos PDR Government.The original 12 Mt/a copper-gold concentrator at Phu Kham commenced production in April 2008. An incremental improvement program resulted in a number of circuit changes being incorporated by 2011, including conversion of conditioning tanks to flotation cells and the installation of a Jameson Cell cleaner scalper. In 2012 the Phu Kham Upgrade Project was commissioned to increase throughput to 18 Mt/a. In April, 2013 the Phu Kham Increased Recovery Project was commissioned to maximise performance by debottlenecking the plant IsaMill™ regrind and cleaning capacity.With the variable mineralogy of Phu Kham ore, control of the c concentrate regrind circuit is essential in terms of achieving effective liberation to maintain concentrator performance. On a routine basis laboratory regrind signature plot data is compared with daily surveys of the operational IsaMills™. More extensive surveys are also conducted to determine size distribution on a mineralogical basis and the effect of fine regrinding on pulp electrochemistry and flotation performance. This paper provides a review of the operating performance of the Phu Kham IsaMills™ with regard to power draw, feed and product size distribution, feed per cent solids, mineralogy and pulp electrochemistry. Operating performance is compared with the IsaMill™ signature plot test for predicting performance.Citation:Harbort, G, Zoetbrood, D and McNab, B, 2016. Operating Performance of the Phu Kham IsaMill™, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 39–50 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By M Thompson

"The Jaguar concentrator, 60 km north of Leonora, Western Australia (WA), consists of a standard closed circuit semi-autogenous grinding (SAG) and ball mill producing a float feed of approximately 60 micron at 70 t/h. Following comminution, separate copper and zinc concentrates are produced by differential flotation. These concentrates are subsequently dewatered by thickening and then filtration.Separate audits of the Jaguar Operation’s copper and zinc concentrate thickeners were conducted to evaluate their performance, following occasions where site personnel had identified unnecessary loss of copper and zinc concentrate to the thickener overflow. The feedwells were identified as the source of the observed problems due to the following issues with their design/duty:lack of retention time in the feedwell as current design is completely opennot conducive to effective mixing required for efficient flocculationdiameter of the zinc concentrate thickener feedwell was undersize for its duty.To improve the performance of the thickeners, it is planned to replace both concentrate thickener feedwells with a high rate design for their respective duties in February 2016. The audits also identified that the feed system requires modifications with particular importance placed on minimising air entrainment of slurry into the thickener feedwell. Minimisation of air entrainment is hoped to be achieved by providing constant head pressure through installation of weir arrangements in the feedboxes and redirecting each feed pipe so that it feeds tangentially into the feedwell. In addition, improvements to the control philosophy of both thickeners will be made with the installation of an ultrasonic bed level probe and bed mass sensor, in order to make real-time adjustments to the underflow pump speed to maintain steady state operation.Following the feedwell replacement and modifications to both thickeners it is expected that losses of recovered copper and zinc will decrease to undetectable levels. Subsequently it is anticipated that a more consistent, homogenous underflow can be produced for downstream filtration.Citation:Thompson, M, 2016. Concentrate Thickeners Feedwell Replacement, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 273–278 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By D Bertoldi, C Haines

"The Waihi Gold Mine (WGM) operated by OceanaGold New Zealand Limited is a wholly owned subsidiary of the OceanaGold Corporation of Australia. Traditionally WGM has stockpiled and processed separate campaigns of open pit and underground ore. The ore is processed via a conventional semi-autonomous grinding (SAG) / ball circuit (SABC). The low aspect SAG mill operates in a closed circuit with two 20" cyclones, whilst the ball mill is also a closed circuit with a 10" cyclone cluster. A major wall movement in April 2015 ceased open pit operations indefinitely, 18 months ahead of the mining plan. This immediately reduced the forecast mill tonnage leaving two options: begin campaign milling or change the operating strategy and target lower throughput. Additional cost pressures necessitated improved milling cost efficiency. The immediate ore restriction limited processing alternatives to within the existing major infrastructure. Available comminution circuit survey data laid the foundation for developing a comminution model using the JKSimMet™ software package (version 6, created by KJTech). A number of flow sheet variants were then evaluated based on predicted throughput and efficiency. The comminution models suggested opportunities for improved efficiency lay in reducing throughput and increasing utilisation rather than on/off campaign milling under the existing operating philosophy. A series of process alterations followed, delivering new cost efficiencies that maintained the current $/t processing cost. This paper aims to review the change in circuit performance and examine the decisions and challenges faced following the transition from a high tonnage SABC circuit to lower tonnage SABC circuit.Citation:Haines, C and Bertoldi, D, 2016. The Transition from Semi-autogenous to Autogenous Milling at Waihi Gold, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 303–312 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By J Pease, P Cameron, D Drinkwater

"In the 1990s metal prices were trending in a long-term decline and the usual cost-cutting exercises were adopted. Cuts to research and development made innovation difficult and the outlook was grim. But necessity is a strong motivator, and these conditions spurred the Mine to Mill movement that optimised across organisational ‘silos’ and utilised new technology tools, innovative software and increased computing power. Many applications of Mine to Mill exploited the fact that comminution is usually the site processing bottleneck and blasting is more efficient at breaking rock than grinding. This approach sought to: understand and characterise rock breakage from mining to the milldevelop models and simulators for blast design, fragmentation, crusher and mill circuitsdevelop tools to measure in real time the particle size distribution of rocks on run-of-mine (ROM) muck piles, at the primary crusher truck dump pocket and on conveyorsensure effective communication across the silos between geologists, blast design engineers, mining engineers and metallurgists.These methods and the technology tools available in the 1990s were widely adopted at numerous sites around the world with significant benefits. Semi-autogenous grinding (SAG) mill throughput increases of 10–20 per cent were common. This was the advance the industry desperately needed. It was low capital cost; it was obvious. It was here to stay.Except, in too many cases, it didn’t. In the minerals price boom of the 2000s Mine to Mill was no longer necessary to ‘survive’, even though it was still good business. Some operations, including some of the early success stories, slipped back to old habits of optimising within organisation silos instead of across them. Fortunately, other operators still embraced Mine to Mill and developed new techniques. Mine to Mill was still successful, but not as widely adopted as we had expected it to be. Now the boom has ended and operations are again under cost pressure. Since these are the same circumstances that created Mine to Mill, it seems time to achieve the wider adoption. Since the 1990s many new or advanced technology tools are now available for Mine to Mill projects: blasthole sensors, new explosives formulations, new blasting techniques and modelling, ore tracking devices, improved image analysis to determine size, texture and colour of coarse ore, grade sensors, whole-stream simulation tools, and even more powerful computing hardware and data analysis software. If we could achieve so much in the 1990s, how much more can we achieve today when we have the same imperative, the same potential and a larger number of high technology tools?Citation:Cameron, P, Drinkwater, D and Pease, J, 2016. The ABC of Mine to Mill and Metal Price Cycles, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 349–358 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By A N. Parry, G van Wyk

"Sensor based automatic ore sorting technologies are used in the minerals industries to efficiently remove waste and submarginal grade material from crushed and screened run-of-mine (ROM) ore, producing a coarse (typically >10 mm) upgraded preconcentrate at an early stage in the mineral processing circuit. This avoids additional energy intensive downstream processing of this rejected component of the ROM feed, leading to lower unit operating costs and reduced tailings disposal volumes.Test work on bulk low-grade gold ore stockpile samples from Central Norseman Gold Proprietary Limited has been conducted, indicating high gold recoveries as well as high material rejection rates. A financial model, based on these results, evaluates grade sensitivity and identifies a minimum stockpile grade for adequate financial returns. The base case modelling estimates that the ex-stockpile grade (including the fines bypassed fraction) can be more than doubled through ore sorting and that the project will be highly viable with strong cash flow generation at stockpile grades as low as 0.7 g/t gold. The modelling will enable the company to benchmark ore sorting options against stockpile reclaim and screening operations currently employed. Citation:Parry, A N and van Wyk, G, 2016. Upgrading Low-grade Gold Ore Stockpiles by Preconcentration Using Ore Sorting - an Assessment of the Economic Impact and Viability, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 179–190 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By T D. Jolly, L A. Balzan, A R. Harris, Z Bauk

"The availability of real-time data in any process control system is critical for effective management of that system. At MMG LXML Sepon Copper Operation in Lao PDR, controlling the copper grade of the feed to the leaching circuit is paramount for maximising both productivity and copper recovery. Since 2008, real-time analysis data has been available to the process engineers from the Geoscan on-belt analyser installed on the Copper Mill feed conveyor, and highly accurate results on copper grade have allowed the process engineers to strictly control blending to overcome the variability in plant feed grade. The availability of real-time analysis data is crucial, as effective sampling of this stream is both difficult and error-prone, being only a snapshot in time of highly variable ore stockpiles, as well as having significant laboratory turnaround delays. Periodic sampling is used to verify the Geoscan data as accurate. Since its installation, the copper result has been the most critical output of the Geoscan. In recent times, the process engineers have sought to utilise other results from the Geoscan to further improve and control the process. One measurement of particular interest involves the real-time measurement of calcium and magnesium as a gauge of ore feed gangue acid consumption. To satisfy this end, accurate measurement of calcium and magnesium is becoming increasingly more important and has been the subject of ongoing collaboration between Sepon and Scantech, the manufacturer of the Geoscan. This paper discusses this work, describing the calibration process and results obtained, while also providing a basis for Geoscan use in operations to enable enhanced process control for all potential Geoscan users.Citation:Balzan, L A, Jolly, T D, Harris, A R and Bauk, Z, 2016. Greater Use of Geoscan On-belt Analysis for Process Control at Sepon Copper Operation, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 231–238 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By S H. Algie, D P. Taplin, S G. Doig

"Suboptimal performance of clusters of hydrocyclones (cyclones), relative to the performance of the individual cyclones that comprise the cluster, is a common phenomenon. The primary cause is well known: uneven distribution of the slurry feed into the individual cyclones. The direct result of uneven distribution is that each cyclone in a cluster performs somewhat differently. Hence, some, if not all, of them do not work at their intended operating points, and the classification is not as sharp as intended. The impact on grade, recovery and milling efficiency will vary depending on the duty of the processing circuit, but the most immediately apparent consequence of uneven distribution is a difference in wear rates in the individual cyclones; this exacerbates the problems of unequal performance of the individual cyclones. In severe cases, and as differential wear proceeds, flows from the individual cyclones may become visibly different. Uneven distribution, once the phenomenon was identified, was seen to be a significant issue in the high-solids hydrocyclone cluster in the ball mill recycle section of Evolution Mining’s Edna May Operation (EMO, Westonia, Western Australia) gold processing plant. In 2012, a FloCEP® hydrocyclone feed distributor system was installed to alleviate the problem. Over the next four years of operation, this innovation has proven its value in the metallurgical and maintenance areas. Individual cyclones now wear at the same rate, greatly reducing the need for operator intervention, as well as increasing overall plant availability through minimising unplanned maintenance. The costs of the installation can be justified by savings in maintenance alone, though the greatest value, as is described in this paper, is in allowing the plant to produce consistently closer to its operational design limits. The FloCEP® system is a low maintenance, readily installed retrofit, based on two patented devices that are combined with complementary proprietary design methodology allowing customisation for specific flow rates and slurry particle properties. Together, these devices produce and distribute a pseudo-homogenous slurry flow without moving parts.Citation:Taplin, D P, Doig, S G and Algie, S H, 2016. Experience with FloCEP® Slurry Flow Conditioning at Evolution Mining's Edna May Operation, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 251–260 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By R Marchant, D Willingham

"Predictive maintenance (also known as PHM or equipment ‘health monitoring’) refers to the intelligent monitoring of equipment to avoid future equipment failures. In contrast to conventional preventive maintenance, the maintenance schedule is not determined by a prescribed timeline; instead, it is determined by analytic algorithms, such as machine learning, using data collected from equipment sensors and/or via simulation.Predictive maintenance offers the following benefits for operators and equipment manufacturers:reduction of equipment downtime by identifying issues before failure, thereby enabling convenient scheduling of equipment service and extending equipment lifetimeautomatic determination of the root cause of the failure, enabling appropriate service to be performed without utilising resources to determine a diagnosis avoidance of costs of unnecessary maintenance and unexpected failures improved safety and product quality.Algorithms and data are critical to predictive maintenance success. Sensor data preprocessing is performed using advanced statistical and signal processing techniques. In the case that data isn’t available for the full range of operating modes, operating scenarios can be simulated. Machine learning techniques are then used to estimate equipment health. Once tested, predictive maintenance algorithms may be operationalised in an IT environment such as a server or cloud. Alternatively, algorithms may be implemented in an embedded system directly on the equipment, allowing for faster response times and significantly reducing the amount of data sent over the network.In this paper, we use both historical and simulated data of the plant under various modes of operation including run to failure, and we then leverage machine learning techniques in MATLAB to estimate degradation and remaining useful life. This technique, of combining both simulation models and machine learning, in the areas of predictive maintenance and equipment health monitoring has been adopted by Safran, makers of aircraft jet engines, since 2007. They now have over 160 modules developed (Lacaille and Aurelie, 2015).Citation:Willingham, D and Marchant, R, 2016. Predictive Maintenance Using Simulation and Machine Learning, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 279–284 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By P D. Munro

"This is a reprise of the paper ‘Back to the Future – Why Change Doesn’t Necessarily Mean Progress’ presented to the Tenth Mill Operators’ Conference in 2009. It was observed that the ‘boom and bust’ cycles of the industry, together with trends in tertiary education and the effects of fly-in fly-out (FIFO) operations raised serious questions about the sustainability of human capital in the mineral processing sector.In 2016 we find ourselves in a ‘bust’ after enjoying a decade of the longest commodity price ‘boom’ in a century. In the ‘boom’ did we:make any technological breakthroughs?put measures in place to improve our human capital, especially in the area of ‘professional formation’?The paper makes observations on the current performance of mineral processing engineers and the organisational milieu in which they operate. It questions whether mineral processing engineers are actually ‘adding value’ at some sites given their organisational and operational practices.Some technical trends are examined and what it might mean for mineral processing engineers.Given the above and demographic trends for mineral industry professionals, changes to the seemingly current laissez-faire model of professional development are proposed.Citation:Munro, P D, 2016. Back to the Future - Still on the Dark Side, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 341–348 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By A Rantala, J Timperi and J Kaartinen, T Maksimainen, O Haavisto

"X-ray fluorescence (XRF) is the most common technique used for online slurry assaying in base metal flotation applications. Typically, assays from feed, concentrate and tailings slurries are used to monitor and control the flotation circuit, with possible additional sampling locations in other main slurry flows inside the circuit. The elemental content detection from the XRF spectrum is relatively straightforward as the spectrum contains element-specific peaks whose height corresponds to the element concentration in the sample. However, centralised XRF analysers measure the elemental concentrations line-by-line, which may increase the sampling interval for an individual line and cause unnecessary response delays, especially in large flotation plants. Reflectance spectroscopy is an emerging technique that can be used to obtain more frequent measurements from slurries. The measurement is based on the mineral-specific absorbance of light in the visible and near-infrared (VNIR) wavelength range. Due to this relatively inexpensive and simple measurement system, it is possible to conduct the measurement simultaneously in several slurry lines. However, the information contained in the VNIR spectra is more difficult to interpret as concentrations of all the minerals in the sample contribute to the measured spectrum and changes in solids content, particle size and mineralogy disturb the elemental content estimation. Therefore, frequent calibration of the measurement is required. This study presents the application of combined reflectance spectrum and XRF measurements for rapid online slurry assaying in a copper-nickel flotation plant. The XRF assays are utilised as calibration samples for the reflectance spectrum measurement, keeping the calibration model up-to-date. The rapid reflectance spectrum analysis is then used to provide an almost continuous estimate of the slurry contents, enabling further improved process monitoring and control.Citation:Haavisto, O, Maksimainen, T, Rantala, A, Timperi, J and Kaartinen, J, 2016. Reflectance Spectroscopy with X-ray Fluorescence for Rapid Online Assaying in a Copper-nickel Flotation Plant, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 85–92 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By M McGrory, A Rodolfo, J Paredes, L E. Manguba, K A Villaspir, G Webb, R Setiagani, H Cardenas

"OceanaGold’s Didipio operation has been in operation for three years. Integral to the flow sheet design is a flash flotation circuit treating a portion of cyclone underflow, consisting of an Outotec SK-500 flash rougher and an Outotec TC10 flash cleaner and a SB-2500 falcon treating flash rougher concentrate to recover fine free gold.Flash copper recovery has been holding steady at 60 per cent, while flash gold recovery at 50 per cent. Gold recovery from the gravity circuit is 22 per cent, bringing the overall flash plus gravity gold recovery to 72 per cent.Operation of the flash rougher is mainly by pulp level control. Control of copper grade in the flash cleaner is mainly controlled by air inflow and flash cleaner pulp level control drives copper recovery. Gold recovery around the circuit is mainly driven by gold head grade.SB-2500 concentrate is scalped with a 250 micron screen with the coarse fraction reporting to a SB-250 falcon, concentrate of which combines with the screen fine fraction to a Gemini table.Citation:Cardenas, H, McGrory, M, Webb, G, Paredes, J, Setiagani, R, Villaspir, K A, Manguba, L E and Rodolfo, A, 2016. Didipio Flash Flotation and Gravity Recovery Circuit, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 123–126 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By T Kojovic

"The index A*b, determined from the Julius Kruttschnitt Mineral Research Centre (JKMRC) drop weight tester (DWT) results, has become well-known in the mining industry as a reliable measure of ore hardness in impact or crushing, having the inferred units of t/kWh. This index evolved from a long history of comminution studies at the JKMRC, including the development of the now superseded JKTech twin-pendulum, the industry standard JK Drop Weight Tester (JKDWT) and the faster alterative JKMRC rotary breakage tester (JKRBT). A reduced version of the DWT, the semi-autogenous grinding mill comminution test (SMC test®), also provides estimates of the A*b though the testing of only one particle size at five specific energies. Experimental determination of A*b using the above devices/tests requires samples, with sufficient mass, to be sent to designated laboratories, registered to conduct such tests. This protocol is fine for bankable and commercial testing, where material characterisation data is used in conjunction with machine specific data in modelling and simulation, and power based calculations. However, for comparative testing, where results are required at the time of sampling (eg for plant troubleshooting or spot-surveys), or for rapid ranking of geometallurgical samples, these existing tests simply do not provide a timely, viable and cost-effective solution. In order to address this critical void in the realm of comparative testing, a new device has been developed, exploiting a central feature of single particle impact testing – that the A*b can be reliably estimated using one precise low energy test. This device, for which a patent is currently pending, called the HIT (Hardness Index Tester), has been precision engineered to allow users to break narrowly sized fragments at a set specific energy, in a safe and easy manner. The manufacturing materials have been chosen carefully to ensure compatibility with the intended use and portability to any site, whilst minimising cost. The device is supplied with a novel quality assurance / quality control (QA/QC) feature, to ensure that the targeted potential energy is consistently delivered. The product from the HIT breakage test can be quickly sized using a single screen to determine the mass per cent undersize, from which the A*b index is calculated directly at site – eliminating the need to send the raw data off-site for analysis. On presized fragments, a single test using 20 fragments takes less than five minutes to complete, and the results are immediately available. The HIT is currently being tested at a major mining laboratory in the US and the results to date have proved it can deliver on all fronts. This paper describes the new prototype device, which offers users a low cost in-house mechanism for estimating the A*b at any mine site, with potential applications on fragments up to 25 mm from drill core, blast chip rejects or the grinding circuit feed. It also outlines the results of field tests carried out by an objective third party mining group and compares the results with those from current industry standard tests conducted on the same material.Citation:Kojovic, T, 2016. HIT - a Portable Field Device for Rapid Testing at Site, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 9–16 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By J Fewings, T McCredden, S Seet, C Fitzmaurice

"Flotation of nickel sulfide ores are generally constrained by nickel grade and impurity concentrations (notably magnesium and arsenic) in the product delivered to smelters. Being a physical separation process, flotation recoveries and grades are limited by the grade recovery curve of a particular operation, where increasing product grades are invariably associated with lower recoveries. Impurities put further pressure on this relationship, as removal of impurities from the final concentrate is almost always associated with nickel losses.Western Areas Ltd are developing a proposed expansion to its Cosmic Boy concentrator to treat an impurity stream, that is high in nickel and would otherwise report to tails. Through the use of BioHeap® technology Western Areas aims to recover the nickel and discard the arsenic to tailings. This expansion will consist of a biohydrometallurgical plant that leaches the nickel arsenic minerals, removing the arsenic as a stable iron/arsenic hydroxide, while recovering the nickel as a high-grade nickel sulfide product (at approximately 50 per cent nickel). This can then be blended with final concentrate to improve nickel grades and recoveries, while simultaneously reducing impurity levels or used to produce high value products like nickel sulfate.The introduction of a small microbial leach plant may be beneficial to base metal concentrators constrained by impurities or grade.Citation:Fewings, J, Seet, S, McCredden, T and Fitzmaurice, C, 2016. BioHeap® - Breaking the Grade/Recovery Curve for Nickel Concentrators, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 361–368 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By R Sinclair, D Landwehr, I Hunter

"The Syama Gold Mine, located in southern Mali, was established in 1990 by Broken Hill Propriety Limited (BHP). The operation began treating oxide, and in 1994 it transitioned to processing hard and refractory ore based on ‘whole-of-ore’ roasting. In 1996, BHP was succeeded by Randgold Resources and the operation ran until 2001, when it was placed into care and maintenance.The Syama ore is classified as a double refractory ore with pyrite occluding the fine grained gold present in the ore and high levels of organic carbon presenting a challenge in terms of preg-robbing behaviour. The ore is extremely competent and this combination of metallurgical features was the main source of metallurgical problems encountered by the previous owners.Resolute Mining Limited (RML) acquired the Syama project in 2004. Following a feasibility study and the development of a revised processing flow sheet the plant was recommissioned in 2008 using a combination of old and new equipment. The revised flow sheet enabled primary sulfide ore to be treated by flotation and roasting of the concentrate to produce a calcine suitable for conventional carbon-in-leach (CIL) processing.Commissioning and ramp up of the plant was a troubled process, with monthly gold production being as low as 3000 oz in 2010. Poor availability of equipment and lower-than-forecast recoveries were the primary contributors.During the last five years, RML has utilised a systematic approach to improve production, focusing on mechanical reliability, metallurgical recovery and process bottlenecks. Modifications to the circuit have been as a result of both innovation and the application of technological improvements. Improvements have been made to the flotation, roasting and CIL circuits and RML has introduced a deslime circuit to treat flotation concentrate, in addition to the very successful commissioning of a new 1 Mt/a oxide circuit in December 2014. These changes have resulted in gold production increasing to more than 20 000 oz per month in 2015.This paper presents the processes, change implementation and outcomes of the modifications made to the sulfide circuit to address the availability and recovery problems.Apart from the expansion of an existing, world-class deposit and discovery of new resources, future improvements on the path to a class-leading gold mine include the continued reduction of the unit cash cost, increase in overall sulfide circuit gold recovery, increased throughput through continued innovation and consistency in the plant’s operation.Citation:Sinclair, R, Hunter, I and Landwehr, D, 2016. Syama Gold Mine - the Journey towards a Class-leading Gold Mine, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 213–224 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By A Giblett, S Hart

"In 2015 operations under the ownership and/or management of all Newmont Mining Corporation subsidiaries (Newmont) produced 5.7 Moz of gold and 619 Mlb of copper from mining operations in five countries, with well over 100 Mt of ore processed by various grinding technologies. Processing methods used in the extraction of metals include flotation, oxidation, conventional cyanidation and heap leaching. The grinding technologies applied in milling operations feeding metal recovery processes include conventional wet grinding semi-autogenous grinding (SAG), rod and ball, dry grinding, concentrate regrinding and ultra-fine grinding, and ball milling of high pressure grinding roll product. SAG/ball (SAB) configurations represent the dominant comminution flow sheet within the company and the circuit configurations employed include SAB, SABC-A, SABC-B and single-stage (SS) SAG milling, with SAG mill feed ranging from run-of-mine (ROM) ore through to secondary crusher product. The collective experiences earned from designing, operating and debottlenecking these various comminution circuits provide many lessons that can be applied to the design and optimisation of future operations. This paper provides an overview of Newmont’s diverse comminution circuits, discusses recent performance and offers some insight into optimisation and design considerations based on recent experience in both endeavours.Citation:Giblett, A and Hart, S, 2016. Grinding Circuit Practices at Newmont, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 293–302 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By T D. H McGrath, O Baker, W P. Staunton, C Ypelaan

"The carbon-in-pulp process has been used extensively in the gold industry since the late 1970s to recovery leached gold from solution. Despite more than 30 years of experience in operating carbon circuits, average gold solution loss has remained at an average of 0.02–0.03 ppm (mg/L), higher than the ‘best practice’ target of 0.01 ppm.Process modelling, such as SIMCIL developed by the Curtin Gold Technology Group (GTG), can provide information on optimum set points; however, manual control of the circuit limits the potential benefits.An automated carbon measurement device, the Scout Carbon Meter, has been developed to allow for automation of carbon concentration measurement, and automated control of the carbon transfer pumps. This paper describes the results from the evaluation of the first two prototypes of the meter.Citation:Staunton, W P, McGrath, T D H, Ypelaan, C, Baker, O and Eksteen, J J, 2016. Optimising Carbon Management - Increasing Gold Recovery and Decreasing Costs with the Carbon Scout, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 225–228 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By D R. Seaman, B Adamson, P Sharman, M McMahon

"The Telfer processing plant commissioned its pyrite regrind and flotation circuit in August 2012. The circuit was designed to regrind pyrite concentrate to a p80 of <30µm then float a gold and copper rich concentrate before tails from the flotation circuit fed the carbon-in-leach (CIL) circuit downstream. Expected benefits were: improved CIL performance that would result from the finer grind and a reduction in cyanide soluble copper to the CIL circuit, as well as a small increase in overall flotation circuit recovery. While the benefits of a finer grind were soon realised, recovery in the post-regrind flotation circuit (named the ‘pyrite recleaner circuit’) was consistently and significantly lower than that expected based on laboratory test work. Selectivity in the pyrite recleaner circuit was virtually nil and copper reporting to the CIL circuit did not change as a result of the pyrite recleaner circuit operation.A pulp chemistry survey of the plant and comparison with the lab showed that the dissolved oxygen (DO) demand in the plant was much higher than that in the lab. Lab flotation tests conducted using nitrogen gas instead of air resulted in recoveries similar to those from the plant. It was identified that the freshly ground pyrite surfaces exiting the regrind mill were consuming oxygen in the slurry and there was insufficient oxygen available for collector adsorption and pyrite depression to occur. Test work, using a pilot regrind mill, showed that a reduction in grind size resulted in an increase in DO demand.A range of oxidising agents were tested in the laboratory and using a pilot flotation rig set-up in the plant. Oxygen was found to be the most reliable and effective agent and options for increasing oxygen delivery to the plant were explored. Scale-up from the lab oxygen requirement to the plant is difficult and efforts to implement a permanent solution for meeting the DO demand in the plant are ongoing.Citation:McMahon, M, Seaman, D R, Sharman, P, Adamson, B and Seaman, B A, 2016. Optimising the Telfer Pyrite Regrind Circuit - Effect of Dissolved Oxygen Demand, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 51–58 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By L P. Gray

"From paving the way in gaining approval for the first metalliferous in-pit tailings storage facility (TSF) in Victoria, to developing a deposition methodology to optimise the storage capacity and provide a final rehabilitated surface which replicates the premining topography, in-pit tailings storage has proven not only to be a cost-effective means for tailings management at Fosterville Gold Mine, but also one which provides significant economic, social and environmental benefits. Coupled with ongoing raising of the existing above ground TSF and commissioning of a new above ground TSF, Fosterville Gold Mine have to date effectively used three open pits for in-pit tailings storage, with one of the pits currently progressing through the capping and vegetation establishment phases of closure.This paper presents the process adopted by Fosterville Gold Mine in their flotation tailings management, from design and operational phases through to rehabilitation implementation. Included within the paper are challenges which have arisen during the process, and a discussion on principals behind the designs and lessons learnt during operation of the facilities.Citation:Gray, L P, 2016. Full Cycle Tailings Management at Fosterville Gold Mine, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 369–378 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By D Hatton, S Wilson, F Orrante, M Taghimohammadi, F van der Walt, N Arslan, M Westcott

"Cayeli Bakir Isletmeleri is an underground copper-zinc mine in turkey. The ore is highly variable with feed grades ranging from 1–4 per cent copper and 1–10 per cent zinc. Due to this variability, ore characterisation and blending strategies are crucial for performance optimisation.This paper presents a case study for a multidisciplinary approach to process optimisation, integrating Geometallurgical and advanced control methods to achieve optimised plant performance. The results from comprehensive metallurgical tests and surveys were used to develop a mathematical model utilising SGS’s Integrated Geometallurgical Simulator® (version number 2.5.24.0). The model was employed to determine the most appropriate operational settings required to ensure that optimised grades and recoveries are achieved for each ore type.SGS’s Modular Expert Technology (MET) expert system was then implemented to target these optimum operational ranges utilising online grade and froth velocity measurements. The successful conversion and deployment of the modelled process parameters into an expert system has resulted in significant improvements in overall recovery and circuit stability.Citation:Arslan, N, Westcott, M, van der Walt, F, Hatton, D, Taghimohammadi, M, Orrante, F and Wilson, S, 2016. A Multidisciplinary Approach to the Optimisation and Control of a Copper-zinc Grinding and Flotation Circuit, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 115–122 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By T Roesch, M Neurohr, S Stratton

"Dwindling commodity prices are forcing today’s mining operations to increase output. Sometimes the solution is to upgrade the existing infrastructure; however, in most cases it has to be achieved with the same or reduced workforce and with the same equipment capacity through improved process efficiency and higher uptime.Measure, Manage and Improveis the mantra for this years’ Mill Operators’ Conference and while this in most cases relates to the above process efficiency, Siemens has set its focus on the availability and uptime aspect since unscheduled downtime is one of the biggest threats to any grinding operation. Pinion misalignments, resonance, unbalance and bearing and gear meshing faults in geared trains, as well as long-term changes in the condition of the mechanical components or structures and auxiliary systems in gearless systems are the main reasons for unscheduled downtimes in today’s mill drive trains. Our paper outlines the efforts that have gone into adapting conventional condition monitoring methods in conventional, pinion driven mill drive trains as well as gearless systems to capture the gradual deterioration of wearing parts or structural changes in the drive train not only on fixed speed application but also on variable speed applications with multiple operating points. The paper further explores the use of condition monitoring systems as a tool to assess spare thermal motor capacity to potentially push equipment beyond its nameplate rating, along with the process that was followed to correlate measured frequency spectra and envelopes to ambient and load data to understand the kinematics of the drive train.Citation:Neurohr, M, Stratton, S and Roesch, T, 2016. Advancements in Condition Monitoring on Mill Drive Trains for Proactive Maintenance and Early Fault Detection Purposes, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 263–272 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016