Search Documents

By Lifeng Li, Jhon Silva-Castro

In a previous work, the authors analyzed the overlapping probability of two adjacent charges in a single hole for pyrotechnic and electronic detonators. This document extends such work to a complete mine blast where more than two holes are detonated. In a mine blast, all the blast holes are connected as a network by detonators to follow a given initiation sequence. Such initiation sequence’s performance is based on the adequate timing between charges in the mine blast. The analysis of the reliability of a mine blast based on the timing between charges and the initiation type is presented in this document. For a long-run time and under proposed operating conditions, the reliability of the mine blast can be analyzed based on the network which is treated as a system. The failure of the system is defined as no success between any two delays charges either in a single hole or in between two holes.

Jan 1, 2016

By Thierry Lavoie, Mark K. Larson

"Engineers at the National Institute for Occupational Safety and Health (NIOSH) and Itasca Consulting Group, Inc., conducted a study to determine the procedure for calibrating a caving model implemented in FLAC3D. The model is calibrated to measured surface subsidence. This sedimentary caving model was developed by Itasca for NIOSH for the purpose of more closely simulating mechanical processes during caving. When a model is considered calibrated to surface subsidence, the load between the extracted panel's roof and floor is a reasonable estimate of gob loading. Such information can also provide an estimate of the amount of overpanel weight that is transferred to the abutment. This load distribution is a parameter needed, for example, to estimate loading of pillars in longwall gate roads. For the current case, a calibrated model resulted in a calculated abutment angle of 30.6°considerably higher than the assumed value used in empirical methods, but reasonable considering the presence of massive stratigraphic members in the overburden. Because of additional information available after this study that the extracted seam height was actually greater in the first panel, a corrected range of abutment angle was estimated to be from 27.7° to 30.6°, still significantly higher than the empirical assumption. The expectation is that better estimates of abutment loading profiles will result in improved evaluations of mine layout design and, therefore, reduce the number of fatalities and injuries resulting from falls of ground.INTRODUCTIONThe safety of miners in underground coal mines depends on careful consideration of the mechanisms involved in failure and transfer of load. The successful design of pillars and panels in longwall and room-and-pillar coal mining requires thorough attention to any information and measurements available that help understand these mechanisms. Although empirical methods, such as Analysis of Pillar Stability (ALPS) Mark (1987); (Mark, 1992) or Analysis of Retreat Mining Pillar Stability (ARMPS) (Mark and Chase, 1997), can provide a sense of success or failure, complex geology and failure in the roof or floor material or complex material behavior of the coal can make evaluation by an appropriate numerical modeling tool necessary. The numerical tool must simulate important mechanisms and appropriate detail that underlie the mechanism. For example, Starfield and Cundall (1988) advised using ""the simplest model that will allow the important mechanisms to occur, and could serve as a laboratory for the experiments you have in mind."" To that end, data gathering about the geology, geometry, and material behavior is very valuable. Such data facilitate selection of an appropriate model and model inputs. Moreover, this data facilitate improved assessment of risk to miners and how to minimize that risk."

Jan 1, 2016

By P. J. Petit

"The complex planning required to achieve any planned production yields multiple and dissociated responses over the life of project (LOP). The customary decision-making process negates the possibilities of developing optimized and integral solutions from operating levels up to business and strategic levels. This results in an inefficient project or overall underperformance of the operation.In the project setting, disconnected trade-offs and improved performance studies become inadequate, because they are site-specific and use only a few comparative parameters. They are often based on a small data-set.Decisions taken to achieve overall objectives require the correct determination and dissemination of key performance indicators (KPIs). The KPIs indicate efficiency in operation, whereby the marginal rate of technical substitution corresponds to the rate of production. It is the necessary condition for optimization. Performance realization for sustainability follows optimization modelling, the latter often being presented with financial results such as business net present value (NPV). It considers techno-financial constraints and provides a strategic and aligned outlook of KPI decisions for an enhanced and integrated outcome.This paper explains a mining case study that is rendered efficient, and through business optimization (BO) short-term and sustainable targets are reached. Business optimization increases the NPV by 14.7%. This is achieved by challenging conventional decision-making associated with maximizing business value by including environmental externalities within the LOP."

Jan 1, 2016

By Fatemeh Pourakbari, Mohammad Reza Yarahmadi, Abbas Sam

Pyrite is the most abundant sulfide gangue mineral in copper porphyry ores. In spite of addition of lime in large quantities to depress pyrite in flotation, considerable amount of this mineral is reported to concentrate, particularly in rougher and scavenger stages. With the Sarcheshmeh pit advancing to a greater depth and reaching to the hypogene zone, the amounts of pyrite and chalcopyrite in the feed are increased. Hence, a reduction in the copper grade and increase in the sulfur content of the concentrate are observed. In this study the effective factors on the pyrite floatability at the circuit flotation was considered at Sarcheshmeh Mine. Mineralization zones in the pit were firstly identified. Then, sampling points were located using GPS system. On the basis of mineralogical composition and morphology, the ore was categorized into five main classes. In this classification the amount of lead and zinc and also pyrite locking with other minerals were analyzed. The study of polished section indicated that inclusion in pyrite was very frequent in all classes, mostly composed of the floatability of pyrite. Flotation tests were performed on the samples of different classes at pH of 11.8 after conditioning time. It was shown that, pyrite floatability was decreased with a decrease in the lead content of the feed samples except for the second class, while for all classes an increase in zinc content contributed to a decrease in pyrite floatability and recovery. It was found that, the lowest pyrite recovery (1.89%) was corresponding to pyrite–molybdenite dominant mineralization with Zn of 0.33% and the highest recovery (86.89%) corresponding to pyrite vein dominant mineralization with Zn equals to 0.9%.

Jan 1, 2016

By Francisca San Martin, Tomas Vargas, Willy Kracht

"In Cu-Mo deposits it is usual to find considerable amounts of pyrite (FeS2). When processing this kind of ore by flotation, pyrite is rejected using lime to increase the pH to alkaline conditions (pH ~10.5). In the case of using seawater without pre-processing, i.e., raw seawater, the lime consumption increases dramatically and the recovery of molybdenite drops due to the precipitation of magnesium hydroxide on its surface. In order to avoid these negative effects, alternative ways of depressing pyrite should be considered.The current work introduces the use of Acidithiobacillus ferrooxidans, bacteria commonly used in bioleaching, as an alternative to depress pyrite in seawater flotation. The paper presents the results of biodepression in three systems: fresh water, water with added sodium chloride at 35 g/L (which corresponds to the salt concentration in seawater ) and seawater. The results show that it is possible to bio-depress pyrite with A. ferrooxidans in natural seawater pH (7.8-8.2). A similar behaviour is observed when running the experiments in fresh water, and in water with sodium chloride added.INTRODUCTIONWater is a scarce but essential resource for human development. The main reason for this scarcity is that, although 70% of the earth's surface is covered with water, only 3% of the total is fresh water and an important part of this water is frozen, so that only 1% of fresh surface water can be used for human activities. In Chile, most of the mining activity is concentrated in the north of the country, located in the Atacama Desert, considered the world's driest desert. That is why some mining companies have chosen to use seawater in their processes. For example, Esperanza (Antofagasta Minerals), and Sierra Gorda (KGHM International) use raw seawater in their flotation processes."

Jan 1, 2016

By M. Poulton, J. A. Botín, C. Gatica

"The Chilean minerals industry faces a shortage of 27.000 new skilled professional by 2023. Enhancing the integration of women into the workforce is a possible solution. This study analyzes the state of women in the mining workforce over the past decade. Several key indicators are presented: percent in the workforce, salaries, career profiles, presence at management level, and participation in academia are studied. The study also analyzes the strategies used by government, industry, and universities to recruit and retain women for the minerals industry. The main results show that women represent 7.4% of the mining workforce in Chile and less than 1% of senior positions with a salary gap of approximately 30%. Systematically, women prefer professional programs in geology, chemistry, and environmental areas. The Chilean statistics are compared to data from the United States mining industry. INTRODUCTION The Chilean mining industry faces a significant shortage of professionals for the next decade which compromises competitiveness and productivity. The demand for human capital in mining depends on several factors. First, the age structure of workforce, which determines future retirement needs. Second, minerals market considerations, determining the amount and size of mining projects entering production in the coming years. Third, the evolution, positive or negative, of productivity, mainly driven by technology and innovation, and negatively affected by the declining ore grades. Finally, negative trends in lead times to production of mining projects, due to social opposition, changing regulations and other project contingencies, negatively affecting the demand for human capital. Regarding the supply of human capital, the fast increase in the technology level of the minerals industry and hence, the increase of technical qualification requirements of the human capital generates a rise in the time required for trade and university education of mining professionals, which may cause imbalances in the labor market. According to (Consejo Minero, 2014) human capital gap in Chile by 2023 will be around 27.000 workers for extractive, processing and maintenance jobs, which represents 14% of the current workforce (Figure 1)."

Jan 1, 2016

By Brent A. Slaker, Khaled M. Mohamed

"Understanding coal mine rib behavior is important for inferring pillar loading conditions as well as ensuring the safety of miners who are regularly exposed to ribs. Due to the variability in the geometry of underground openings and ground behavior, point measurements often fail to capture the true movement of mine workings. Photogrammetry is a potentially fast, cheap, and precise supplemental measurement tool in comparison to extensometers, tape measures, or laser range meters, but its application in underground coal has been limited. The practical use of photogrammetry was tested at the Safety Research Coal Mine, National Institute for Occupational Safety and Health (NIOSH). A commercially available, Digital Single-Lens Reflex (DSLR) camera was used to perform the photogrammetric surveys for the experiment. Several experiments were performed using different lighting conditions, distances to subject, camera settings, and photograph overlaps, with results summarized as follows: The lighting method was found to be insignificant if the scene was appropriately illuminated. It was found that the distance to the subject has a minimal impact on result accuracy, and that camera settings have a significant impact on the photogrammetric quality of images. An increasing photograph resolution was preferable when measuring plane orientations; otherwise a high point cloud density would likely be excessive. Focal Ratio (F-stop) changes affect the depth of field and image quality in situations where multiple angles are necessary to survey cleat orientations. Photograph overlap is very important to proper three-dimensional reconstruction, and at least 60% overlap between photograph pairs is ideal to avoid unnecessary post-processing. The suggestions and guidelines proposed are designed to increase the quality of photogrammetry inputs and outputs as well as minimize processing time, and serve as a starting point for an underground coal photogrammetry study.INTRODUCTIONThe stability of underground mine ribs has been a safety concern for underground coal mines for decades. Unfortunately, the average rib fatality rate has been about 1.3 per year between 1996 and 2013 (Jones et al., 2014). In an effort to better understand coal rib behavior, photogrammetry is being investigated in this study as a measurement tool for surveying ribs in an underground coal mine environment."

Jan 1, 2016

By M. R. MacIver, M. P. Pawlik

"An image analysis method based on chord length distributions is applied to the batch settling of polyacrylamide flocculated kaolin suspensions. Two features of the interaggregate void space, the void chord length distribution mean and the white-to-black distribution ratio are extracted from an image series obtained over the two hour settling experiments. This approach produces three signal values, from two different probability distributions that can be measured as an indication of underlying sediment bed density and aggregation state. Further work is required on the physical interpretation of the signal, the image acquisition conditions, and the parameter selection methods. It is suggested that this chord length based feature extraction technique may be a useful signal to monitor during batch settling or thickening.INTRODUCTIONFew in situ techniques are available that can be used to directly measure aggregate properties within sediment beds in thickeners or secondary settlers. Typical process variables monitored include rake torque and height, bed level and pressure, feed rate and density, underflow rate and density, settling rate, and overflow turbidity; yet these process variables are only weakly related to process dynamics (Concha et al. 2014). Additional process monitoring signals, based on the direct measurement of aggregate properties could improve solid-liquid separation control and allow the extraction of more detailed information from batch settling experiments.Several optical methods exist for measurement of moving suspensions of aggregated solids in the dilute concentration regime, such as focused beam reflectance measurement (Peng and Williams 1994), and the turbidity fluctuation method (Gregory 1985). In the more concentrated region of a thickener, acoustic backscatter penetration and attenuation measured with an acoustic probe and changes in the underlying solid concentration in the highly concentrated, near-bed region of a thickener as a function of height and time (Hunter et al. 2012). While machine vision for froth monitoring has been thoroughly studied with at least five commercialized technologies (Aldrich et al. 2010), its’ application to the study of thickening has been limited."

Jan 1, 2016

By D. B. Dreisinger, M. R. Tavakoli

"Vanadium has been produced from a variety of sources. This metal is known to make aqueous solutions of complex speciation as a function of vanadium concentration and pH. Considering the method of leaching, the impurities in the pregnant leach solution, and the planned vanadium product, different extractants and flowsheets can be applied for solution purification. This paper reviews the purification of vanadium leaching solution using organophosphorus, solvating, and amine extractants. This review focuses on vanadium separation from iron, molybdenum, and uranium, which are often present in vanadium resources such as primary ores, fly ashes, and spent catalysts.RÉSUMÉ Le vanadium est produit à partir de diverses sources. Ce métal est connu pour permettre des solutions aqueuses de spéciations complexes en fonction de la concentration du vanadium et du pH. En tenant compte de la méthode de lixiviation, des impuretés dans la solution mère de lixiviation et du produit de vanadium planifié, divers agents d’extraction et schémas de traitement peuvent être mis en oeuvre pour purifier la solution. Le présent article étudie la purification de la solution de lixiviation du vanadium au moyen d’extractants organophosphorés, solvants et aminés. L’étude cible la séparation du vanadium du fer, du molybdène et de l’uranium, lesquels sont souvent présents dans les ressources de vanadium telles que les minerais primaires, les cendres volantes et les catalyseurs usés."

Jan 1, 2016

By B. Schulz, T. Leißner, R. G. Merker

"Ores enriched in critical rare earth elements (CREE) keep on being of particular interest. The CREE are Nd, Eu, Tb, Dy, including Y. In conjunction with beneficiation tests on Y-mineral bearing flotation tailings of complicated mineralogy, the Mineral Liberation Analyses (MLA) was used to work out processing characteristics fraction-wise in terms of modal mineralogy, mineral recovery, locking and liberation, and particle size.Size fractions from mechanical sieving (“real fractions”) as well as fractions created virtually by using filters on the MLA-data of the unsieved head material (“virtual fractions”) were investigated comparatively thereby. The ""virtual-sizing-approach"" features a much simpler sample preparation procedure and considerably lower cost if a fraction-wise investigation of a head sample is needed. It can be conveniently applied to intimately locked ores needing a fine grinding to a particle size distribution (PSD) range below 25 microns for instance. However, its practical use is sometimes disputed in terms of the reliability of the results. Results are shown for the main Y-bearing mineral xenotime and selected main gangue minerals of a low grade REE-ore.The influence of sample representativeness, sample preparation and particle counting statistics turned out to be of crucial importance. Given that all preconditions for reliable results are met, locking characteristics, modal mineralogy, and even PSD trends can be read from virtual fractions.The authors encourage processing engineers to use the virtual approach. They propose practical measures to improve the reliability of the MLA results, identify and tackle conflicting results, and mitigate evaluation problems that may arise."

Jan 1, 2016

By Joe Hachey, Jerry Dorn, Jeff Schutt, Derek Penrice

"Sound Transit’s East Link Project, a $3.7 billion (2015 $), 14-mile light rail extension, will connect downtown Seattle with the rapidly developing east side cities of Bellevue and Redmond. Among the most technically challenging aspects of the Project is the 2,435 foot long Downtown Bellevue Tunnel (DBT), which will be constructed through the central core of Bellevue underneath 110th Avenue NE using a combination of Sequential Excavation Methods (SEM) and cut and cover tunneling. The 1,980 foot long central SEM component of the DBT will be mined at shallow depth through challenging and complex geology, comprised of glacially overconsolidated soils, containing both regional and perched groundwater conditions and in close proximity to existing high rise buildings. The paper shares lessons learned from the planning decisions and risk based approach to the investigation, design and procurement processes which shaped the DBT configuration and enabled a successful transition to the project’s construction stage. INTRODUCTION The East Link Project is a voter-approved $3.7 billion (2015 $), 14-mile extension of the existing Sound Transit (ST) light rail transit (LRT) system from downtown Seattle, across Lake Washington via I-90, to the cities of Bellevue and Redmond on the east side of Lake Washington. With targeted completion in 2023, East Link will provide riders with an efficient and reliable connection between the largest population and employment centers on the east side and downtown Seattle. The project alignment is indicated in Figure 1 below.ST completed the Preliminary Engineering (PE) phase of the East Link project in late 2011. Subsequently the final design contract for the easternmost seven miles of the project was awarded to the H-J-H Team, a joint venture comprised of HNTB, Jacobs Engineering and Hatch Mott MacDonald in February 2012. H-J-H’s final design scope includes approximately 7 miles of double-track LRT between the east end of the I-90 East Channel Bridge and the Overlake Transit Center Station. While the project scope is extensive and diverse, the focus of this paper is the DBT. The DBT is located immediately north of the East Main Station, and travels approximately one half mile through downtown Bellevue under 110th Avenue NE between Main Street and NE 6th Street; terminating at the Downtown Bellevue Transit Center (BTC) Station. The location and extent of the DBT is indicated in Figure 2."

Jan 1, 2016

By B. Birol, M. N. Saridede

"Slag density is a significant factor in determining the process efficiency of the electroslag remelting (ESR) process, where calcium fluoride (CaF2)-based slag is formed synthetically to refine metal ingots. Although there are some former studies investigating the density of CaF2-containing slags, the prediction models focusing on them are applicable only to some specific systems. The present study aims to build a model to predict density for a wide range of CaF2-containing ESR slags. To investigate density for various slag compositions, CaF2-Al2O3-based and CaF2-Al2O3-CaO-based slag compositions were prepared. Additionally, some minor constituents like FeO, MgO and MnO were added to a 5:3:2 CaF2-Al2O3-CaO slag in order to investigate the effects of these constituents on the slag. The volumes of the prepared slags were measured in a tube furnace at 1450-1550 °C using the sessile drop technique, and their densities were calculated. The results showed that for the slags, density is related to optical basicity, and therefore a prediction model based on an Arrhenius equation was built. The model was tested with data from literature, and its limitations and validity are discussed.IntroductionThe electroslag remelting (ESR) process is a refining method in which a metal ingot is remelted under a synthetic slag. These synthetic ESR slags are mainly composed of calcium fluoride (CaF2), calcium oxide (CaO) and aluminum oxide (Al2O3). Other constituents like iron oxide (FeO), magnesium oxide (MgO), manganese oxide (MnO) and chromium oxide (Cr2O3) are added to this system in relatively low amounts, according to the type of steel ingot to be refined. The prediction of slag properties, such as electrical conductivity, viscosity and density, is crucial for the selection of the synthetic slag in order to obtain the required process parameters, like temperature, the passing time of the molten metal droplet through the slag, and metal-slag separation (Akbari, Reitz and Friedrich, 2009; Hara and Ogino, 1981; Mattar, El-Faramawy and Fathy, 2002; Mehrabi, Rahimipour and Shokuhfar, 2005; Presoly, Korp and Schneider, 2008).As slag density affects metal-slag separation in the ESR process, predicting the density of an ESR slag is important for appropriate refining and improved product quality. Although there are many studies investigating the density of slags (Akbari, Reitz and Friedrich, 2009; Aune, Hayashi and Sridhar, 2005; Hara and Ogino, 1981; Matsushita, 2011; Mills and Keene, 1987, 1981; Seetharaman et al., 2013; Shu, 2007; Shu and Chou, 2013; Sikora and Zielinski, 1974; Xu et al., 2012; Zhang and Chou, 2010), the prediction models built are generally valid for oxide-containing slags (Aune, Hayashi and Sridhar, 2005; Bottinga and Weill, 1970; Mills and Keene, 1987; Seetharaman et al., 2013; Shu, 2007; Xu et al., 2012; Zhang and Chou, 2010). These models were built on either the molar volumes of the constituents (Bottinga and Weill, 1970; Mills and Keene, 1987) or the thermodynamically calculated enthalpy or free energy of mixing, which can be applied to a system containing constituents sharing an ion, such as an O- ion for oxide systems (Aune, Hayashi and Sridhar, 2005; Hillert, 1980; Persson et al., 2007). Some recent studies modeled the density of some oxide slags on their optical basicity (Shu, 2007; Shu and Chou, 2013; Xu et al., 2012; Zhang and Chou, 2010)."

Jan 1, 2016

By C. Pace, D. Darlington, A. Montera, C. Lingren

"A phosphate beneficiation plant in Utah is using isotope-based Prompt Gamma Neutron Activation Analysis (PGNAA) technology to analyze the entire slurry streams of the incoming feed and final product in order to adjust the flotation circuits in near real time and optimize the plant output. The plant has gained greatly improved visibility/control and has reduced product variability for improved profitability and product quality. This paper takes a look at the economics as well as application details and the difference this technology provides in a phosphate application. SIMPLOT PHOSPHATES INTRODUCTION Simplot’s Vernal, Utah Phosphate Mine and Mill are located in the northeast corner of the state in the Uinta Mountains along US Highway 191, eleven miles north of the town of Vernal. The phosphoric acid and fertilizer plant fed by the Vernal mine is located 94 miles Northeast of Simplot Phosphates in Rock Springs, WY.At the Vernal plant, loader and shovel mining to 85 Ton capacity trucks is done at an annual rate of 3.8 Million tons of ore. Run of mine ore is crushed in a mineral sizer to minus 14 inch diameter at the rate 11,500 tons a day and transported to the SAG Mill’s 130,000 ton surge stockpile by overland belt. ORE RESERVES The ore is a Phosphoria Formation of sedimentary rock type dating to the Permian Age. The ore body rests over a 25 mile area on Weber Sandstone from the Pennsylvania and Permian geologic period. Layers of Phosphate Rock can vary in thickness from 0.3 up to 2.1 feet, alternating with layers of Mudstone. The eastern edge of the ore’s body Panel “G” runs 16 feet deep with a feed grade of 21.5% P205 with lower MgO diluents of less than 2.79%."

Jan 1, 2016

By Alejandro Ferrada Vergara

Most blasting techniques that are designed to improve fragmentation and subsequently improve ore work index to downstream comminution processes, apply powder or energy factor increases, either by stretching the drilling pattern (burden/spacing ratio) implementing faster initiation sequences or using more energetic explosives. The new application will move detonation parameters up, making the blasting process riskier for the surrounding boreholes, explosive column or initiation systems functioning.

Jan 1, 2016

By Peter Richards, Alexander Lewis-Gray, Mark Davies, Nicholas Katsikaros

"Gekko Systems developed the Gekko Resin Exchange Column (G-REX) in order to optimise the recovery of gold in complex leach-to-electrowinning processes, as an intermediate step using a highly gold-selective resin to isolate contaminant metals. The AuRIX®100 resin produced by Purolite is licensed exclusively to Gekko, with the G-REX column designed specifically for this resin (Lewis-Gray et al, 2015). Operational experience has been gained at the CGT Ballarat Gold Plant in near continuous operation since 2008, treating unclarified concentrate leach solution. The extension of the technology to higher throughputs and more complex chemistry is discussed.Aurix®100 ResinAuRIX®100 resin is a cross-linked polystyrene alkaline resin developed by Henkel (Virnig et al, 1996). The resin beads are off-white in colour, spherical, with a nominal size of 100% +600µm. This resin is highly selective for gold and silver over many metals, by way of extracting precious metal cyanide complexes from leach solutions with a pH less than 11.5. The higher end of the pH scale produces best selectivity according to the order of preference: Au > Ag > Hg > Zn > Ni > Cu > Co > Fe. Purolite produces the resin and Gekko Systems maintains licensing of AuRIX®100 resin for use in its G-REX column as part of its unique suite of gravity gold handling equipment.Significant cost savings over carbon-in-solution (CIS) systems are realised with AURIX®100 resin, of around 4% to 12% in capital savings and 27% to 40% in operating costs (Virnig et al, 2004). Allied to this is that AuRIX®100 resin is not susceptible to fouling, that is, the resin does not load with inorganic salts or organic compounds which would affect the loading and extraction of precious metals. To counter any potential for fouling by inorganic salts, in service a dilute acid wash is carried out periodically on the resin to unblock resin pores."

Jan 1, 2016

By Ulrich Maidl, Marc Comulada, Janosch Stascheit

"INTRODUCTION Cohesive soils are notorious for causing clogging of the cutter head and the excavation chamber of tunnel boring machines (TBMs). While clogging leads to a drastic reduction in excavation performance, it further induces higher wear of tools and other parts of the cutter head and may even prevent a controlled support of the tunnel face and, thus, lead to face collapse and excess settlements or sinkholes. Employing well-balanced soil conditioning techniques, the clogging tendency can be significantly reduced. The monitoring and control of soil conditioning as well as the timely detection of potential clogging tendencies require a close monitoring of all relevant machine parameters and measurements. To this end, a reliable and powerful Process Controlling software that gathers all machine and process-related information is a prerequisite for successful mitigation of clogging-induced problems. The remainder of this contribution is organized as follows: First, a brief introduction to the Process Controlling system PROCON is given. Afterwards, the mechanisms and mitigation techniques of clogging are discussed. Finally, an example is given how Process Controlling has been employed to soil conditioning in a tunneling project with highly clogging soils.PROCESS CONTROLLING Being both the active part and a huge measuring device, the shield machine represents the core component in mechanized tunneling. This machine comprises a manifold of complex components and devices that require constant supervision and control and, thus, is equipped with a manifold of different sensors that provide a continuous monitoring of the state and condition of the machine (Maidl & Stascheit, 2014). If these data are put into the whole context of the tunneling process, they can provide insight to the assessment and optimization of the performance and to the prediction of potential risks and hazards such as, for example, the tendency of clogging of the cutter head."

Jan 1, 2016

By J. N. Van der Merwe, M. Mathey

"The South African squat coal pillar strength formula, developed by researchers from the Chamber of Mines Research Organization in the 1980s, predicts an exponential increase in coal pillar strength once a critical width-to-height ratio of 5 is exceeded. The arguments that have been proposed in favour of this formula are discussed critically in this paper.Field experience with squat pillars in the USA and evidence from published physical, analytical, and numerical model pillar studies corroborate the fact that a squat effect is unlikely to occur in coal pillars at width-to-height ratios less than 10. Furthermore, an exponential increase in peak strength of coal pillars does not exist. An alternative design criterion for squat pillars in South Africa is therefore suggested. IntroductionFive decades of coal pillar research in South Africa have produced a wealth of information on the mechanisms contributing to the strength and failure of in-situ coal pillars and accompanying phenomena. The relevant knowledge was sourced from, and for, a South African coal mining environment that remained largely unchanged in the second half of the 20th century. The depth of mining seldom exceeded 250 m, with mined seam thicknesses averaging 3 m and typical pillar width-to-height ratios (w/h) of 3–4.It is therefore not surprising that comparatively little research has been directed at the prediction of coal pillar performance in deeper deposits, where squat pillars of larger width-to-height ratios will be required to support the overlying strata. However, a thorough understanding of squat pillar performance will be necessary should the remaining deep coal deposits of the country be extracted in future, for instance in the Waterberg or Ermelo coalfields.A squat coal pillar strength formula has already been proposed in South Africa. The origin of this formula will be discussed in some detail in the following sections and its appropriateness will be critically reviewed against a great amount of evidence from relevant squat coal pillar research conducted internationally."

Jan 1, 2016

By Emilio Cordero Cordero

En los proyectos de excavaciones subterráneas, túneles de obra civil y galerías mineras es necesaria la realización de cálculos para el sostenimiento adecuado para cada situación y comprobar que este cumple los parámetros de seguridad indispensables para garantizar la estabilidad de la excavación en el tiempo. En este sentido, el texto señala el uso de SDT(software) como aplicación informática decuada para el cálculo de sostenimiento en túneles y galerías mineras que suministra una respuesta a las necesidades de proyectistas e ingenieros mineros. Dicho software se basa en cerchas metálicas con capacidad de deslizamiento (perfiles THN), cerchas de perfil HEB, pernos de anclaje y hormigón proyectado en túneles y galerías mineras que utiliza el método “Convergencia – Confinamiento”, procedimiento de referencia en el cálculo y diseño de sostenimiento en excavaciones subterráneas, con las premisas de sección circular, presión sobre el sostenimiento uniforme y el campo de presiones hidrostático.

Jan 1, 2016

By M. Oliazadeh, A. Vazirizadeh

"The inclusion of small amounts of silicon, phosphorus and sulphur in iron ores or concentrates can have a profound effect on the steel making process and thus on the final iron and steel products. In nature however, it is inevitable that iron deposits contain unwanted elements. Each element has its own distinct effect on the final steel product. The effect of high silicon is the formation of gray iron. Phosphorus mainly increases hardness and strength, lowers solidus temperature and increases fluidity and cold shortness. Finally sulphur contamination causes cracks in the iron texture when smelting and forms white iron when casting. Overall, the acceptable level of phosphorus, sulphur and silica in the iron concentrate should be less than 0.04%, 0.15 % and 1.5 % respectively.Scarcity of high grade iron ores necessitates using lower grade ores with higher amounts of impurities. The purpose of iron concentrators is to increase iron grades to an appropriate level suitable for steel making as well as removing impurities. Although many impurities can be traced in the ore, the most predominant impurities are limited to one or two elements. In this paper the beneficiation methods for removing SiO2, P and S are presented, including flotation, and the parameters that need to be considered in the design of beneficiation plants are discussed. Finally industrial cases are discussed along with their metallurgical performance.INTRODUCTIONIn metal sector, value of iron ores and concentrates is determined by iron percentage as well ascontent of:• Useful elements (Mn, Ni, Cr, V, Ti): natural alloying elements in steel• Deleterious impurities (S, P, As, Zn, Pb, K, Na): impair metal properties or complicate operational process in blast furnace• Fluxing components (Si, Ca, Mg,, Al)Sulphur and copper result in red-short, phosphorus is the cause of cold brittleness and arsenic and copper decrease welding characteristics. Sulphur should not exceed 0.15 in commercial ore. Acceptable sulphur content in ores and concentrates for producing sinter and pellets is 0.6%max, as sintering and heat hardening of pellets remove sulphur 60-90%. Phosphorous content in ores, sinter and pellets is limited to 0.07%-0.15%. 0.00.1% As max, 0.1-0.2% Zn max and up to 0.2% Cu are allowed in iron-ore part of the blast furnace burden for the production of standard conversion pig iron. Slag-forming components are divided into basic oxides (Ca, Mg) and acidic (Si, Al). Higher ratios of basic to acidic oxides are preferred since this reduces raw fluxing material."

Jan 1, 2016

By F. Habashi

"Extractive metallurgy was divided into the three sectors pyro-, hydro-, and electrometallurgy in 1959 when Professor Joseph Newton at the Idaho School of Mines in Moscow mentioned this in his book Extractive Metallurgy. Pioneer hydrometallurgists who built this discipline can be traced to the alchemists in the ninth century. It is now a mature subject of great importance in which pressure plays a vital role. Short biographies of some hydrometallurgists and the processes they invented are briefly outlined.INTRODUCTIONHydrometallurgy is the use of aqueous solutions to recover metals from ores. It is a relatively new discipline when compared with pyrometallurgy the use of fire to melt ores and recover metals which was practiced in ancient times. Hydrometallurgy can be traced to the time of alchemists whose concern was the transmutation of base metals into gold. Although alchemists did not succeed in their venture yet they described many reagents that are useful today. For example, they prepared sulfuric acid by distillation of iron vitriol, muriatic acid by distillation of sulfuric acid with salt, and nitric acid by reaction of sulfuric acid by reaction of sulfuric acid with salpeter. Jabir Ibn Hayyan the Muslim alchemist who lived in the ninth century (Figure 1) described aqua regia a mixture of nitric and hydrochloric acid that can dissolve gold although either acid has no action on gold. THE MIDDLE AGESIn the Middle Ages, it was reported that copper was recovered at Rio Tinto in Spain by allowing copper-containing pyrite to be exposed in piles to the action of air and rain. Copper sulfate solution obtained was treated with pieces of iron to precipitate metallic copper—a process that was called cementation. Georgius Agricola (1494–1555) (Figure 2) a medical doctor in Saxony who used to visit mines and smelters to examine miners and metal workers, described in his book De Re Metallica the parting of gold, i.e., separating of silver from gold by acids."

Jan 1, 2016