Search Documents

By Thomas L. Barkley

"In early 2015 the Seed Waveform method was used to measure the Geologic response of the MesabiIron Formation to explosives energy input. This single charge wave form was then used to design acritical first blast at a newly developed Taconite mine. This initial blast had several irregular restrictions on design and performance. It had a very unusual “Frying Pan” shape, the regulatory agency required that no fly rock land in State owned waters less than 200 feet (61 m) away, there was no open face to blast to. Design criteria included the need to detonate the blast with two sinking cuts, and have the sinking cuts meet through a narrow neck between the cuts. All these had to be met using a 16 inch (406mm) diameter hole."

Jan 1, 2016

By B. K. Gorain

"The Air-Metabisulfite (AMBS) process has been developed to treat complex copper, molybdenum and precious metals (gold, silver) bearing ores using brackish and sea water. This process was able to produce significantly better copper concentrate grades and higher recovery than possible using conventional lime and/or cyanide based processes for certain complex ores with high sulphide gangue minerals. The AMBS technology in now used commercially following a rigorous evaluation process emanating from laboratory curiosity to plant applications. In addition, many projects have embraced this technology at a feasibility level involving various complex ore bodies.This paper presents a summary of the findings from testing the AMBS technology on various ores types. Experiences gained from this successful development from bench to piloting and then to plant applications are also presented in this paper.INTRODUCTIONProcessing of sulphide copper, molybdenum and precious metal ores typically involves flotation of copper bearing minerals while depressing non-sulphide and other non-copper sulphide minerals such as pyrite, pyrrhotite and sometimes arsenopyrite. Though in many precious metal ores, the values are in these sulphide minerals as well. The conventional method employed in the industry to produce a saleable copper concentrate requires depression of these non-copper sulphide minerals using an alkaline pH above 9.5, though 10.5 to 11.5 is more common. Alkalinity is controlled by the addition of a pH modifier. Lime is normally employed as a pH modifier due to its relatively low cost; however, the costs associated with adding lime can be significant and the effectiveness of lime as a depressant could be drastically reduced when the process water supplied to the flotation circuit contains high level of dissolved salts. In some cases, a small amount of cyanide is used along with lime to depress non-copper sulphide minerals especially when its proportion to copper sulphide minerals in the ore is higher than three."

Jan 1, 2016

"Controlling dust generation and keeping it below permissible limits at the working face of a room and pillar mine is a challenge for mine operators. With the recent changes in the respirable-dust regulation, it has become increasingly difficult. The current most effective practice of dust control at a continuous miner face in an underground mine is the use of a flooded-bed scrubber. A study carried out by the National Institute for Occupational Safety and Health (NIOSH) stated that a flooded-bed scrubber, under its optimum condition, can achieve cleaning efficiencies between 58 and 90 percent. The performance of such a system can be maintenance intensive. Other industries face similar dust control issues. The University of Kentucky partnered with Toyota Motor Manufacturing for the development of a novel wet scrubber for capturing paint overspray, with capture efficiencies in excess of 98 percent and minimal maintenance. The aim of this study is to assess the ability of this novel wet scrubber to capture respirable dust in an underground coal mine. This paper presents the conceptual design and the computational fluid dynamics (CFD) modeling of this novel wet scrubber. It discusses the results of the CFD simulation performed on the novel wet dust scrubber. INTRODUCTION Dust generation from underground coal mining is an inescapable phenomenon. No matter the practices employed, it inevitably occurs. Elevated concentrations of coal dust are potential health and safety hazards. Although dust in an underground coal mine cannot be completely avoided, its influence can be mitigated through good engineering practices. The effect of dust on the health of mining personnel has had a significant impact. The prolonged exposure of airborne respirable dust (< 5 µm) can cause coal workers’ pneumoconiosis (CWP), silicosis, emphysema, and chronic bronchitis, collectively known as black lung (U.S. Department of Labor, 2014). According to the National Institute for Occupational Safety and Health, black lung has killed more than 10,000 miners between 1995 and 2004 (NIOSH, 2008). In addition to being a health issue, coal dust is also a safety issue to the underground coal miners. The generated dust, if not captured, is dispersed into the mine air through the ventilating air and deposited downwind on the return entries’ surfaces. In the event of a methane explosion, the coal dust, if insufficiently diluted with rock dust, triggers a coal dust explosion which is much more severe than a methane explosion and causes more damage (Kenneth et al, 2006). The Jim Walters No. 5 Mine and the Upper Big Branch Mine disasters which together killed 42 people and resulted in damage worth millions of dollars in property are the examples of coal dust explosions (U.S. Department of Labor, 2001 & 2010)."

Jan 1, 2016

By D. Michaud, C. Bazin, S. Lévesque, L. Pérez-Barnuevo, H. Longuepée

In recent years, with the emergence of Geometallurgy, a great effort has been made to characterize ore resources as early and accurately as possible, to allow better design and a more efficient operation of mineral processing circuits. In this context, core logging plays an important role, since drill cores provide the first insight into the ore characteristics. However, to satisfy geometallurgical requirements, traditional core logging does not suffice. New tools and methodologies need to be developed for the automation of core logging and the acquisition of mineralogical data better related to mineral processing performances. In this paper, a methodology for the geometallurgical characterization of drill cores is proposed, based on the drill core textural patterns. Textural pattern is defined here as the macroscopic spatial arrangement of minerals. The Mont-Wright iron ore deposit (Quebec, Canada) is used as a case study. The first part of this work aimed at analyzing the potential link between the iron ores textural patterns observed in drill cores and their response to ore processing, namely comminution and concentration. Preliminary results show similar performances in terms of energy consumption and heavy liquid separation for samples showing the same textural pattern. In the second part, this work seeks to develop a methodology for the automated identification of drill core textural patterns by the application of digital image analysis and discriminant function analysis. The results obtained show that this methodology is able to discriminate between the textural patterns identified at Mont-Wright with a good rate of success. Therefore, this work lays the foundation for the development of a new drill core characterization tool, which would allow for the early prediction of the iron ore behaviour during mineral processing through the identification of drill core textural patterns.

Jan 1, 2016

By Karel Rössler, Petr Vítek

"The Ejpovice tunnels in Czech Republic were built by EPBM in soft Clyashale, and in weathered profile with low soil overburden. The segmented liner at the cross-passage openings required support, which would not interfere with the EPBM clearance envelope during the scheduled pull back of the EPBM through both tunnel tubes. For that reason support frames or radial bolting could not be used. Steel rods inserted into the neighboring segments during the ring assembly, and later grouted were tested and realized as an innovative solution. The paper presents practical experience gained with the segmented liner support during cross-passages construction. INTRODUCTION An innovative solution using the grouted dowels was developed and realized for sixteen cross-passage openings of the twin Ejpovice Tunnels, whose construction was part of the railway track Rokycany – Plzen modernization. The following paper described practical experience gained with the innovative support of cross-passage openings, which was realized by short steel dowels grouted within the segments of the EPBM segmented liner. The paper is a continuation of the paper published in WTC 2015, which described the design aspects of the grouted dowels support, while the following paper concentrated on the production, and the performance of the dowel support observed during the breakout for the cross-passages openings. The connection by grouted dowels was patented by Metrostav, a.s. Company THE EJPOVICE TUNNELS CONSTRUCTION The Ejpovice tunnels construction started in 2013. The start of the high speed train operation through the tunnels was planned for 2018. The project was funded by the state government with the support of European Union funds of up to 70%.The tunnels were excavated with one EPBM (Earth Pressure Balanced Machine) with the external diameter of 9.89 m. The segmental liner inner diameter was 8.7 m, and thickness of 0.4 m. First, the South tunnel tube was excavated from the East portal, then the EPBM was pulled back through the South tunnel, and the excavation was started from the same portal for the North tube. After the South tube was freed from the EPBM excavation operations the cross-passage construction started. Due to the short time schedule, in the North tube the cross-passage construction started while the tunnel was still under construction. Therefore, the cross-passage construction was performed concurrently with the segments transportation, and with the EPBM pull-back through the tunnel. There were 8 cross-passages along the tunnels with a maximum distance of about 500 m, Fig.1."

Jan 1, 2016

By Z. Sample

"INTRODUCTION This past year commodity prices continued their dip with increased volatility causing market values to slide another 16% putting increased pressure on even the largest companies to improve their free cash flow.[1] Without a recovery in commodity prices in sight, companies must find a sustainable method to improve returns in the current economic climate. In an effort to improve plant sustainability, the mineral processing industry is investing in advanced automation technologies and innovative processing methods that are both more reliable and more efficient than ever before. One such breakthrough technology is Heap Leaching (HL). This method of extraction has certain advantages over traditional metallurgical methods making previously unsustainable operations economically feasible. While HL is already seeing use in the gold and copper industries among others, recent developments may allow for the use of HL to process primary sulfide ores which make up about 80% of today’s ores.[2] For this reason, this emerging technology is poised for exciting growth. Unfortunately, as with any process change, the implementation of HL projects requires significant training on both the control system as well as the underlying process, and further, due to the complex nature of the HL process, this can be a particularly difficult task. DEMOGRAPHIC TIME BOMB Even before the implementation of these new technologies, the availability of the skilled workforce has already become a significant problem for the mining and mineral processing industries. From a survey of 912 mining professionals, Stratum International found that a mere 0.4% of senior level candidates were between the ages of 25 and 34 and a similar proportion aged over 75 years.[3] This indicates that there is both a deficiency of young skilled workers and a skilled workforce that is retiring earlier than the previous generation. Combined with data published by the US Department of Labor stating that the median age of the mining workforce is approaching 50 years old, research suggests that up to 50% of skilled mining and mineral process professionals are expected to retire in the next 5 years, leaving with their irreplaceable knowledge and experience.[4] While it is projected that the labor pool will be sufficient to fill open positions, the real question is if this young workforce will have necessary skill sets and experiences. In addition to a rapidly aging workforce and an inexperienced labor pool, a study done by the Oil and Gas Journal showed that it takes about 7 years, on average, for new workers to achieve a level of competency that permits them to assess risks and appropriately make decisions.[5] Not only is this figure is in direct conflict with the typical tenure of 5 years in one position meaning that the thinly spread skilled labor will be required to become senior staff before they are able to achieve competency in their current role, this also means that these millennials are not given the opportunity to become competent in their role before the retirement of the more experienced workforce."

Jan 1, 2016

By A. Jolly, A. R. Kumar, T. Novak

"Coal dust in an underground mining environment has always been a health and safety issue, especially with longwall faces. Efforts to integrate a flooded bed scrubber within a longwall shearer are underway at the University of Kentucky (UK) in order to reduce worker exposure. Small scale physical modeling, along with numerical modeling and full-scale experimentation, are engineering tools being used by the authors for simulating operating conditions underground. Recent advances in affordable 3D printers offer a means for fabricating accurate, scale models for obtaining timely insights prior to building large, expensive test setups. Comparing scale-model results with those of numerical modeling, such as computational fluid dynamics (CFD), lends guidance and confidence in a proposed design. This paper discusses the small scale physical modeling of a longwall shearer with an incorporated flooded-bed dust scrubber in its operating environment. A tracer gas was used in the model in lieu of dust to measure dust-capture efficiency. Results obtained from the physical model are presented and compared with those of CFD model. The small scale model and the CFD results demonstrate good agreement. Dust capture results show the usefulness of the approach in advance of actual design implementation. INTRODUCTION Dust generation is an undesirable, but innate, byproduct of all mining processes. It is particularly problematic in underground coal mining, where coal dust poses potential hazards from two fronts – health and safety. Coal workers’ pneumoconiosis (CWP), commonly referred to as black lung, is a chronic lung disease that results from the long-term overexposure to respirable coal dust. Although the prevalence of CWP has steadily and significantly declined over the three decades following the Federal Coal Mine Health and Safety Act of 1969, a study by the National Institute for Occupational Safety and Health (NIOSH, 2008) indicates that significant health hazards associated with respirable dust still exist within the coal mining industry. In addition to being a health hazard, coal dust can also create a potentially catastrophic safety hazard. Dust that is not captured or removed at its source is suspended and transported throughout a mine by the ventilation airstream. This float dust is subsequently deposited on all mine surfaces along its travel path. Without adequate application of rock dust to these surfaces, forces from a localized methane ignition can reintroduce settled coal dust into the airstream creating an explosive mixture. Therefore, capturing and removing coal dust at its source mitigates the probability of two major hazards that continue to plague the mining industry."

Jan 1, 2016

By D. K. Sarkar, J. Perron, J. D. Brassard

"Nearly perfect spherical shaped water drops rolling-off from the surface of lotus leaf is one of the beauties of nature. This kind of surface is called superhydrophobic, since the water does not like it. Physically, a superhydrophobic surface provides a contact angle (CA) of water over 150°. The combinations of both mico-nanostructure topography as well as low surface energy are essential to have such high CA on a surface. Nano-micro structured superhydrophobic surfaces have been developed in different methods. (i) Monodispersed fluorinated silica nanoparticles have been synthetized via Stöber Sol-Gel process and deposited on various surfaces, such as aluminium or glass, to obtain transparent superhydrophobic thin films. (ii) Similarly, zinc stearate nanocomposite coating has been fabricated by spray process on the same substrates. These thin films are found mechanically robust with drag reduction of coefficient 16% lower than as-received surfaces. (iii) By electrodepositing pure zinc on steel surfaces and further coating it with diluted room-temperature vulcanized silicone rubber, the surface become superhydrophobic. This superhydrophobic surface protects the steel against corrosion by increasing the polarization resistance from 1.5 k? on steel to 44.4 k?. This coating also reduced the ice adhesion on the steel surface 6.3 times as compared to bare steel substrates. Globally, these superhydrophobic surfaces have tremendous applications against corrosion reductions, drag reductions and ice adhesion reductions.INTRODUCTIONSuperhydrophobic coatings are increasingly attractive to the industry and academia due to their unique self-cleaning properties as a result of their water repelling characteristics. Fabrication of superhydrophobic coating is an inspiration from nature as water is seen to repel on many natural surfaces such as those of the lotus leaves, butterfly wings, water striders’ legs, and so on (Gao & Jiang, 2004; J. Huang, Wang & Wang, 2006; Neinhuis & Barthlott, 1997; Zheng, Gao & Jiang, 2007). This non-wetting phenomenon is well understood on lotus leaves, shown on the Figure 1 (a), and it is considered as the basis of the studies of superhydrophobicity. The existence of this binary structure on the surface of the lotus leaves allows a large amount of air entrapment and consequently reduces the contact area of water on it and the presence of low surface energy waxy components with reduced affinity to water together leads to the superhydrophobic properties. The phenomenon is shown on Figure 1 (b). Cassie and Baxter (Cassie & Baxter, 1944) as well as Wenzel (Wenzel, 1936) proposed two mathematical models to explain the wetting phenomena on rough surfaces that leads to superhydrophobic properties. By definition, superhydrophobic surfaces are characterized by a water contact angle value = 150° with the rolling off of water drops from the surfaces (Sarkar & Saleema, 2010). Superhydrophobic surfaces find tremendous importance in the technological world where it can applied in domains such as anti-corrosion, anti-biofouling, electrowetting, icephobic and even in drag reductions (Bushnell & Moore, 1991; Cao, Jones, Sikka, Wu & Gao, 2009; Carlborg & van der Wijngaart, 2010; Carré & Mittal, 2009; Y. Huang, Sarkar & Chen, 2010a; R. Karmouch, Coude, Abel & Ross, 2009). However, the most important challenge faced by industries is their feasibility large scale in an effective an economical manner."

Jan 1, 2016

By Douglas Tesarik, Mark K. Larson, Habte Abraham, Heather E. Lawson

Dynamic failures, or "bumps", remain an imperative safety concern in underground coal mining, despite significant advancements in engineering controls. While many factors have been empirically linked to the occurrence of dynamic failure events, identifying a consistent, repeatable set of criteria within a field setting has proven elusive; conditions generally associated with dynamic failure might produce an event at one site, but not another. Conversely and more troubling, dynamic failure could occur where relatively few of these factors exist. The presence of spatially discrete, stiff roof units, such as paleo channels, are one such feature that has been linked to the occurrence of dynamic failure events. However, an empirical stratigraphic review investigating the relative frequency of discrete units in bumping versus non-bumping deposits indicates that no significant difference exists based on this criterion alone, and that instead an apparent relationship exists between reportable bump history and the overall character of the host rock with respect to stiffness. Due to the complexity of the bump problem, however, these results are not conclusive, as they do not take into account any variable other than the presence or absence of stiff members in the roof lithology; To weight the relative impact of changes in a single variable, such as the thickness or location of sandstone members, it must be examined in isolation-i.e. in a setting where all other variables are held constant. Numerical modelling provides this setting, and the effects of variability in a stiff discrete member in a hypothetical longwall mining scenario are investigated within the context of three stratigraphic "types'', as determined by the ratio of stiff to compliant stratigraphic members; Compliant, Intermediate and Stiff A modelling experiment examines changes in rupture potential in stiff roof units for each stratigraphic type as discrete unit thickness and location are manipulated through a range of values. Results suggest that the stiff-to-compliant ratio of the host rock has an impact on the relative stress-inducing effects of discrete stiff members. In other words, it is necessary to consider both the thickness and the distance to the seam, within the context of the host rock, to accurately anticipate areas of elevated rupture induced hazard; acknowledging the presence of a discrete unit within the overburden in general terms is an insufficient indicator of risk. Through modelling of anticipated changes in the placement and dimensions of discrete units within their stratigraphic setting, elevated rupture-induced bump hazard can be anticipated on a case by case basis. Were similar modelling studies conducted at mine sites in tandem with tracking of problematic discrete stiff units, areas of elevated rupture risk could be anticipated in advance of mining. Developing this predictive capability beyond identifying rupture potential in discrete roof members is essential to the eventual elimination of dynamic failure related worker injuries and fatalities. As stress is a necessary component in the occurrence of dynamic failure events, this finding helps to refine our understanding of the role of individual stiff, strong roof members in bumping phenomena, and suggests that a more holistic view of overburden lithology, combined with site-specific numerical modelling, may be necessary to achieve greater miner safety.

Jan 1, 2016

By Robert E. Schock, Eric J. Risberg

"Less than 20,000 years ago, the last of the glaciers retreated from the Chicago region. They left behind sheets of glacial clay till underlain by dense, over-consolidated till (“hardpan”) below which is the limestone bedrock, found about 100 ft (30.5 m) below street level. The most notable feature in this profile is the unusually soft clay till that has historically been called “Chicago Blue Clay.”But the founding fathers of Chicago really didn’t care about what was under the ground. They recognized the importance of the city’s location as a potential trade and transportation hub. With access to the East through the Great Lakes and access to the West through the Mississippi River system, the viability of the city was evident. Chicago’s population grew rapidly. The city continued to grow through the Civil War years, but was dealt a devastating blow in 1871 by the Great Chicago Fire, leaving the city in ruins. The Birth of the SkyscraperAfter the cleanup of the Great Fire came the first real building boom in Chicago’s history. During this era, buildings were generally founded on shallow footings bearing on sand or clay. Many multistory buildings were constructed between 1880 and 1890 on spread footings. The first tall buildings were constructed with load bearing masonry walls. These early tall buildings suffered significant settlement as the soft clay underwent consolidation.The Home Insurance Building, built in 1885, was 12-stories tall and is generally acknowledged to be the first “skyscraper” in the U.S. It was the first building constructed with an iron skeleton frame instead of load bearing masonry walls. Spread footings were used under the interior columns in an effort to better distribute the loads, but the building still experienced large settlements.Construction began for the Monadnock Building in 1891. The 17-story building was built using load bearing walls 7 ft (2.1 m) thick, supported on rail-grillage footing foundations. When completed in 1893, the Monadnock Building boasted the title “World’s Largest Office Building.” The total building settlement over the past 125 years has been measured at over 20 in (0.51 m). The engineering community in the late 19th century observed settlement, but did not yet understand the process of consolidation of the soft clay beneath the city. During this time, many of the new buildings required structural repairs during and after construction; the problem was especially acute in buildings where highrise towers joined lower podium structures."

Jan 1, 2016

By I. Sedat Buyuksagis, Jamal Rostami, Ali Naeimipour

"Improving the safety of underground openings and optimizing ground support systems requires reliable ground characterization. This includes understanding the joints, discontinuities, and rock strength. Joint information can be obtained from borehole cameras, but measuring in-situ rock strength is very difficult. Use of borehole probes can be an ideal and efficient way to meet this requirement. This paper discusses the development of the Rock Strength Borehole Probe (RSBP) and presents the preliminary laboratory/field test. This device can be an accurate, flexible, quick, non-disruptive, and cost-effective alternative to estimate the rock strength inside boreholes in underground mines and tunnels. In addition, the scratch testing procedure in the laboratory by means of a newly developed miniature linear cutting machine is explained. Based on the results of these tests, two equations are developed to estimate the uniaxial compressive strength (UCS) and Brazilian tensile strength (BTS) of the sedimentary/metamorphic rocks. These equations, are based on testing 27 different sedimentary, igneous, and metamorphic rocks by full-scale scratch tests, including the cutting tests by a miniature disc. The results show a good correlation between the normal force and the compressive strength of sedimentary rock if the depth of the scratch is known. No significant correlation was observed for igneous rocks, due to the impacts of grain size.INTRODUCTIONEstimated rock mass properties are essential input for geomechanical studies and stability analysis for any structure constructed in or with rock. The availability of geological information is the crucial component of rock mass classification. One of the important parameters in evaluating rock mass properties is the intact rock strength. This parameter is usually measured by testing the core samples, obtained from exploration boreholes. These samples are subsequently tested in geomechanics laboratories. The test results offer limited information about the rock at the few boring locations despite all the efforts and costs. In addition, these results may not necessarily be representative of the behavior of the rock in the field as the test cannot provide the insitu condition of the ground."

Jan 1, 2016

By Dongfeng Yun, Zhu Liu, Wendong Cheng, Zhendong Fan, Dongfang Wang, Yuanhao Zhang

"For the purpose of studying the strata behavior due to multislicing top coal caving longwall mining along-the-strike direction in steeply dipping extra thick coal seams, the shield support pressures of the upper and lower slices of Panel 37220 in Dongxia coal mine were monitored using the KJ513 dynamic monitoring system. The set up rooms adopted the ""horizontal line-arc segmentinclined line"" form and used different types of shield supports. The results showed that the strata pressure of upper slice Panel 37220- 1 changed slightly along the strike direction, while along the dip direction it exhibited strong to weak pressure from bottom to top. The first weighting interval oflower slice Panel 37220-2 was about 60.Sm, and the average periodic weighting interval were about 22.6m. The strata behavior of Panel 37330-2 exhibited a spatiotemporal characteristic in that periodic weighting occurred first in the middle-upper part, followed by the middle and upper parts, arc segment, and finally the lower part. During the periodic weighting, the weighting interval and intensity also exhibited strong space characteristics. The average dynamic load coefficient was 1.48 and the maximum lateral pressure of the side shield was 900Kn1000kN.INTRODUCTIONThe steeply dipping coal seams account for about 20% of proven reserves and 10% of output in China (Wu, et al, 2014). About 50% of coal mines in the western China have steeply dipping seams, and are mainly distributed in Sichuan, Gansu, and Chongqing. When the steeply dipping seam employs longwall mining along the strike direction is employed, the waste rocks fill the gob nonhomogeneously along the dip direction, the deformation and caving of surrounding rocks exhibit obvious asymmetry and spatio-temporal characteristics with particular and complex strata behavior. In recent years, many research on strata behavior due to multi-slicing top coal caving longwall mining along-the-strike direction in steeply dipping extra thick coal seams have been performed with significant results (Shi, 1999; Wu, Xie, and Ren, 2010; Wu, Xie, Wang, and Ren, 2010). However, there has been a complete lack of research on monitoring the strata behavior due to multi-slicing top coal caving longwall mining in steeply dipping extra thick coal seam. Therefore, the strata behavior of multi-slicing panels 37220-1 and 37220-2 was systematically investigated in this research."

Jan 1, 2016

By C. Heckman, M. S. Moats, A. Luyima, W. Cui

"Nucleation and growth of copper on 316L stainless steel from synthetic acidified copper sulfate was studied in the absence and presence of chloride ions and/or organic additives – HydroStar® 4208, DXG-F7® and Cyquest® N-900 – using a potentiostatic technique. The current–time data obtained at 0.16V versus the SHE were analyzed using nucleation and growth models. Scanning electron microscope (SEM) images of deposits produced at 300 A/m2 show that the addition of 20 mg/L chloride ions increased the size and reduced the number of copper nuclei. Potentiostatic current–time data from the electrolyte without organic additives, and confirmed by SEM images, indicate progressive nucleation with two-dimensional growth under diffusion control. None of the organic additives studied at a concentration of 2.5 mg/L with 20 mg/L chloride changed the nucleation and growth mechanism, but the additives increased the number and reduced the size of copper nuclei, leading to more uniform coverage of the stainless steel substrate.IntroductionElectrowinning of copper is an important process in the manufacture of high-purity copper metal. Approximately 20 percent of the world’s refined copper is produced from acidified copper sulfate solutions by electrowinning (Schlesinger, Sole and Davenport, 2011). In many plants, copper is electrodeposited on AISI 316L stainless steel substrates for a period of 6-7 days, after which the copper is stripped from the blanks. Even though the deposition time for a commercial copper electrowinning circuit is around one week, it is critically important to control the nucleation, growth and nature of the initial deposit (Sun and O’Keefe, 1992).Deposit morphology and structure are influenced by the real current density at the electrode surface. The real current density across the cathode surface is made uniform by proper design of the electrowinning cell and electrodes and careful operational practice. Even with good design and control, some current maldistribution occurs. The outcome of severe current maldistribution is poor deposits that affect product quality and/or increase energy consumption. To combat current maldistribution and create a larger operating window in terms of current density, temperature and copper concentration, small amounts of organic smoothing agents – traditionally, guar products – are added to copper electrowinning electrolytes. Moreover, these additives inhibit the growth of copper nodules and lead to improved deposit quality by producing bright, smooth and dense cathodes.Recently, the use of polysaccharides, such as HydroStar 4208 and DXG-F7, and polyacrylamides, such as Cyquest N-900, has been reported in commercial electrowinning tankhouses as replacements for guar (Ashford, Clayton and Sandoval, 2012; Robinson et al., 2013; Sandoval, Morales and Bernu, 2010). However, little information has been published on the effect of these new organic additives, especially regarding the nucleation and growth mechanisms of copper electrodeposits in their presence."

Jan 1, 2016

"The Ohio River Bridge East End Crossing Tunnel requires a 75-year service life of its cast-in-place reinforced concrete lining. This twin-tube 3-lane (each tube) highway tunnel is about 55-ft wide and 30-ft high. Since unified tunnel service life prediction methodology does not exist in the US, challenges occurred during the design-build phase of this project. These challenges include the methodologies in determining the reinforced concrete’s degradation mode, the lining’s surface chloride concentration level, the reinforcing steel’s critical chloride threshold value for corrosion, how to verify the concrete’s diffusion coefficient, and the durability impact from concrete crack width. This paper presents a methodology in verifying the proposed concrete mix can achieve the service life requirements. This methodology can be adopted for service life prediction for future tunnels to be built in the US. INTRODUCTION The Ohio River Bridge East End Crossing (ORBEE) Tunnel is part of a Public Private Partnership project, which connects transportation network between Louisville, Kentucky and southern Indiana. Located in Louisville, Kentucky, the twin-tube highway tunnel provides northbound and southbound lanes of the Kentucky approach to a new bridge across the Ohio River. Tunnel lengths are approximately 1,675-ft and 1,685 for the northbound tube and the southbound tube, respectively. Connected by two cross-passages, both tubes have a roadway width of 40-ft, for 3-lane traffic, and a vertical clearance of 26.5-ft.The tunnel was constructed by drill and blast method with shotcrete and rock dowels as initial ground supports. The final tunnel lining system includes: •,Nominal 16” cast-in-place reinforced concrete lining, with 2” and 3” concrete covers over reinforcing steel for its extrados and intrados, respectively. •,20” cast-in-place reinforced concrete invert slab, with 4” and 3” concrete covers over reinforcing steel on its top face and bottom face, respectively. •,PVC waterproofing system around tunnel perimeter, excluding invert slab. •,Perforated PVC groundwater collection pipes on both sides of the tubes and one below the invert slab of each tube."

Jan 1, 2016

By Gilles Recher, Jörg Riechers, Albert Lueghamer

"INTRODUCTIONIn view of a global trend towards urbanization, more and more trunk sewers and combined sewer overflow tunnels (CSO) with medium to large diameters and the corresponding link sewers are currently built and under design. Shielded tunnel boring machines using segmental lining as tunnel support represent an efficient solution for construction of new wastewater and supply tunnels. Especially in the field of sewers, the durability of concrete structures both exposed to any groundwater present on its exterior and to aggressive waste water as well as gases on its interior is a key requirement. Despite thorough research on segmental lining and mechanized tunneling machinery, conventional thermoplastic liners show comparatively minimal progress in terms of practical advancements. This is in contrast with the development of the latest segment embedded high density polyethylene (HDPE) system. Based on experiences achieved, this paper discusses the latest development of an integral protective lining system in respect of material characteristics and its adaptability to both project and customers’ demands. Reviewed performances, as the bondage behavior of the embedded HDPE system at axial stress loads due to acting thrust cylinders during ring build as well as the ability to drain pressurized water behind the embedded membrane, tested at full scale segments, are also presented. The paper is round off by presenting first details of sewer projects endeavoring to utilize this cutting-edge solution for an integral concrete protection, which will be commenced beginning of 2016.CASE HISTORIES ENCOURAGE ADVANCEMENTS Past experience has shown that unprotected concrete surfaces as well as chemical based linings such as coatings, sprayed linings and cured in-place-systems cannot reach the desired life times. Also the fact that in deep tunnel sewer system hardly maintenance is possible, a durable and maintenance free system is required which only can be reached by applying mechanical anchored HDPE (CPL)."

Jan 1, 2016

By P. T. Bissert, L. Yan, M. D. Klein

"Federal regulations require that refuge alternatives (RAs) are located within 305-m (1000-ft) of the working face and spaced at one-hour travel distances in the outby area in underground coal mines in the event that miners cannot escape during a disaster. The Mine Safety and Health Administration mandates that RAs provide safe shelter and livable conditions for a minimum of 96 hours while maintaining the apparent temperature (AT) below 35°C (95°F). The National Institute for Occupational Safety and Health used a validated thermal simulation model to examine the mechanisms of heat loss from the RA to the ambient mine and the effect of mine strata composition on the final internal dry bulb temperature (DBT) for mobile tent-type RAs. The results of these studies show that most of the heat loss from the RA to the ambient mine is due to radiation (51%) and conduction (31%). Three mine width/height configurations and three mine strata compositions were examined. The final DBT inside the RA after 96 hours varied less than 1°C (1.8°F) for the three mine width/height configurations and less than 2°C (3.6°F) for the three mine strata compositions. INTRODUCTION Following a mine disaster, workers will try to escape the mine. If their escape is futile, they can take shelter in a refuge alternative (RA). In 2008, the Mine Safety and Health Administration (MSHA) mandated RAs in mines to ensure that a safe and livable shelter is provided for a minimum of 96 hours, and that the apparent temperature (AT) does not exceed 35°C (95°F) inside the RA [1]. An ongoing concern with RAs is the potential to exceed this limit. The temperature rise inside an RA is due to the metabolic heat released by the occupants as well as heat released by the carbon dioxide scrubbing system. The National Institute for Occupational Safety and Health (NIOSH) tested a 10-person tent-type training unit RA in its Safety Research Coal Mine (SRCM) to investigate heat buildup in RAs. The 10-person capacity for the tested RA is based on 1.4 m2 (15 ft2) of floor space per miner. NIOSH-developed simulated miners, which are heat input devices that generate both sensible and latent heat, were used to represent the metabolic heat generation of an average miner (117 W) for testing in the SRCM. It was found that the number of occupants in an RA may need to be reduced based on the ambient mine temperature, which varies from mine to mine [2]. To further research temperature rise inside an RA, ThermoAnalytics, Inc. (TAI) was contracted by NIOSH to perform thermal simulations of the tested 10-person mobile tent-type RA. TAI developed a thermal model of the SRCM using RadTherm software, which incorporates a human thermal model (HTM) to represent the equivalent metabolic heat loss of a miner within the RA’s enclosed environment. The thermal model was previously validated by comparing simulation results with test results [3]. During a mine disaster in which miners would have to take shelter in an RA, mine ventilation may not be available. As such, mine ventilation was off for both the testing in the SRCM as well as in the simulations. This paper discusses the heat loss mechanisms and the effects of mine strata composition and mine width and height associated with a ten-person tent-type RA."

Jan 1, 2016

By S. S. Al-Thyabat, A. M. Ghrair

"Printed circuit board (PCB) is the main part of any electric or electronic device, providing mechanical support and electric connection for the board eclectic components such as capacitors, resistors, diodes etc. PCB consists of non-conductive substrate overlaid with one or more layers of copper sheets. They also contain appreciable amounts of base metals (copper, nickel, tine, and aluminum) and precious metals (gold, silver, and rare earth elements (REE)) which end up in the landfill at the PCB end-of-life.PCB recycling E-waste in general is a profitable business; many valuable raw materials, precious and base metals, can be extracted with high purity. Approximately, one metric tonne of PCBs may contain 80-1500 g of gold and 160–210 kg of copper. The precious metals recovered from PCBs occur at concentrations higher than commercially mined minerals. Also PCB recycling is very important to our environment since many heavy metals (e.g. lead) may be leached from the landfills to the underground reservoirs. In Jordan, however, the work conducted on E-waste and PCB recycling in particular is limited; currently most of the E-waste is either exported or dumped in the landfill.In this work, a combination of physical (magnetic separation), physicochemical (flotation), and chemical methods (leaching) were used to compare metals concentrations in leach liquors produced from a concentrates resulted from a combination of these methods. It was found the leach liquor of the magnetic fraction of the PCB coarse size gave the highest concentration of Fe, Al, and Ni while concentration of Cu was higher in leach liquor of nonmagnetic sink fraction. On the other hand, metals concentration almost similar for both sink and float of the fine size fractions, indicating even distribution of metals concentrations in the fine size fractions."

Jan 1, 2016

By Ergin Arioglu, Werner Burger

"SUMMARY The Istanbul Strait Road Crossing Project includes a 3.34 kilometer subsea tunnel excavated by TBM with an excavation diameter of 13.71 m. The tunnel will incorporate two road decks, each employing two traffic lines and shoulder with the daily capacity of 100,000 light vehicles. The tunnel alignment crosses full face rock sections with heavily fractured zones due to tectonic events as well as a long central stretch of difficult mixed face and very variable soft ground conditions. The demanding ground conditions and the large diameter in combination with realized face pressures well above 10 bar required a highly specialized and well adapted TBM. The paper describes the project challenges and the related technical solutions incorporated within the TBM design as well as the real site experience. INTRODUCTION In 2013, a 13.71 m diameter Mixshield was manufactured in Germany for the Istanbul Strait Road Crossing Project. The delivery of the TBM in late 2013 was a major milestone for the Istanbul Strait Road Crossing Project, also known as the Eurasia Tunnel Project. The Eurasia Project (www.avrasyatuneli.com.tr/en) consists of a 14.6 km route including a 5.4 km tunnel segment in its central part crossing the Bosphorus. The 3.34 km subsea section of the tunnel was excavated in closed mode using a Mixshield TBM. The remaining tunnel length is constructed by sprayed concrete lining (SCL) method followed by a cast in place (CIP) lining or by cut and cover (CC) structures for the TBM transition boxes (Figure 1, right). Other project sections on the European and Asian side consist of upgrading and widening surface access roads towards the tunnel. Conceptual ideas of connecting Asia with Europe via a tunnel crossing the Bosphorus have been around for an extended time and only became realistic towards the end of the 20th century based on significant technical developments in mechanized tunneling. Feasibility studies for a new Bosphorus crossing in 2003 and 2005 confirmed and suggested a road tunnel in its present alignment as the preferred solution. Following an international tender process the Ministry of Transport, Maritime Affairs and Communications of Turkey assigned ATAS, a special purpose company formed by Yapi Merkezi (Turkey) and SK E&C (South Korea), to design, build and operate the Eurasia Tunnel Project. The Implementation Contract was signed in February 2011. In 2012, Herrenknecht AG was selected as the supplier for the 13.71 m Mixshield TBM."

Jan 1, 2016

By Andrew Cushing, Joe Carvalho, Jon Hurt

"INTRODUCTIONThe shales of the Greater Toronto Area (GTA) have been known to experience time-dependent deformations (TDD); those initiated by excavation-induced stress relief which progress with time as a function of rock porewater salinity, access to freshwater (or air) of lower salinity, clay and calcite content, and the buildup of swelling pressures within the rock mass. These deformations can induce long-term pressures on shaft walls and tunnel linings, especially if the permanent works are constructed soon after excavation, with very little time delay. This paper presents measurements of time dependent deformation of recent shaft and tunnel projects constructed in the GTA, and draws conclusions regarding the main influences on the TDD. The key input parameters for the numerical predictive model are critically assessed. Projects which are discussed include the Billy Bishop Airport Pedestrian Tunnel, Hydro One Midtown Tunnel and Hanlan Feedermain (Contract 3).MECHANISM OF TIME DEPENDENT DEFORMATIONExplanation of MechanismThe Georgian Bay Shale unit consists of typically moderately weathered to fresh, grey to dark grey, fine to very fine grained fissile shale interbedded with slightly weathered to fresh grey, fine grained calcareous siltstone and limestone interbeds. There are two distinctive features of the shale in the Greater Toronto Area (GTA). One is a high horizontal stress regime, and the second is long-term time dependent swelling behavior which develops when the following factors occur (Lo and Micic, 2010):• Stress relief of the rock mass• Outward salt concentration gradient from pore fluid of the rock to the ambient fluid• Availability of fresh waterThe swelling is a consequence of the reduction in confined stress in the rock which occurs upon excavation in combination with a differential gradient in salinity between the saline rock porewater and freshwater or even humid air. Osmotic and diffusive processes result in a decrease in the salinity of the rock porewater achieved by an overall increase in the water content, resulting in volumetric expansion of the shale rock over time. The development of this time dependent deformation (TDD) relative to the time"

Jan 1, 2016

By J. P. Germiquet

"Rock properties have a material impact on mining processes, including drilling performance. An investigation using point loaded index (PLI) data converted to uniaxial compressive strength (UCS) has revealed that a direct relationship between grain size and UCS exists at Mogalakwena Mine. This correlation is best seen in unaltered rock, with lower correlations for altered rock types. Measurements from the new RockMa system installed on drill rigs can be used to obtain rock strength data to validate the current rock strength domains and create additional data for the next benches below. An investigation of penetration rates in different lithologies shows that rock composition plays an important role in determining drill performance. Additionally, there is an inverse relationship between rock strength and drilling penetration rate – a measure of how efficiently a hole is drilled.The domaining of grain-size-adjusted UCS at Mogalakwena Mine will allow more accurate scheduling of drill rigs through increased knowledge of rock strength in various areas. Successful rock strength domaining has the potential to be incorporated into blast indexing and predicting crushing/milling performance.IntroductionThe optimization of mining and processing through geometallurgical characterization of ore are key drivers of value realization (Deutch, 2013). Rock strength is one such property and is affected by, among other variables, composition, texture, and grain size (Ozturk, Nasuf, and Kahraman, 2014). Mogalakwena Mine is exploiting the intrusive Platreef PGE (platinum group element)-bearing orebody which forms part of the northern limb of the Bushveld Complex. This complex orebody exhibits areas of metasomatic alteration, metamorphism, and sporadic mineralization of the footwall and hangingwall (Nex et al., 2006). Understanding this variability is paramount due to the implications for rock strength and hardness, which in turn affect crushing, milling, and liberation efficiency. These variables must be known prior to blasting in order to optimize mine and plant processes using in-situ variables. This necessitates predictive modelling (Deutch, 2013). Geological and geotechnical data was sourced from the Overysel (OY) exploration database for the study. Point load testing was done for each borehole and the results converted to uniaxial compressive strength (UCS) (Akram and Bakar, 2007). The relationship of lithology, texture, and grain size with UCS revealed an inverse relationship between grain size and UCS in unaltered rock. The relationship was not present in altered rock types. A comparison of mean strength and hardness results indicated that Bond work index and UCS may be related. Drilling performance is affected by UCS (Bourgoyne et al., 1986), and this was proven using recent measurements obtained during drilling. Lastly, grain-sizeadjusted UCS values were applied to a 3D model for the OY property."

Jan 1, 2016