Search Documents

By Matthias Neuenschwander, Andreas Theiler, Patrick Steinle, John Singer, Martin Vogel, Diego Martini, Ömer Ündül, Markus Weh

"Quartz Dust is a major health hazard in underground works, wherever the ground contains quartz and depending on the chosen method of excavation. A research project initiated by the Swiss Tunnelling Society and realized by the Swiss Federal Institut of Technology, Zurich, established a correlation between the potential of quartz dust generation during excavation and well known geotechnical characteristics – the Cerchar Abrasivity Index CAI and the Uniaxial Compressive Strength UCS - of ten typical Swiss rocks. The results are at the center of a new guideline by the Swiss Society of Engineers and Architects on the requirements for early project stages regarding ventilation and logistics in function of the quartz dust related risk of the expected ground type of the project. The approach presented could be applied worldwide, contributing to more effective health protection as well as to better cost stability in underground works. CONTEXT Respirable quartz dust (aerodynamic diameter of particles < 10 micron) is universally recognized as a major workplace health hazard. Chronic bronchitis, silicosis and lung cancer can be caused by excessive exposure to quartz dust, as has been proved by many medical studies. Therefore, the legislations of many nations specify a maximum workplace concentration (Maximale Arbeitsplatzkonzentration MAK, Occupational Exposure Level OEL). In Switzerland, for example, the Threshold Limit Value TLV for respirable Quartz or Crystalline Silica imposed by the Federal Committee on Exposure Levels (Grenzwertkommission) is 0.15mg/m3 air. Some nations refrain from establishing a OEL because of the carcinogenic nature of quartz."

Jan 1, 2016

By Patrick Oriez, Chris Norris, Alain Mercusot

"Temporary mechanical ventilation is one of the fundamental requirements in guaranteeing a healthy atmosphere in underground construction works in order to protect the health of persons working on the site. It is therefore essential to conceive a system which meets the requirements of the whole of the worksite and for all phases of work which takes into account all aspects pertaining to its design, dimensioning, justification, installation, maintenance and validation. In doing so, the ventilation design and the selected apparatus to be installed shall meet with the degree of health protection and the quality of air of the worksite as defined by the legislation in force in France, through limiting the concentration of the different pollutants associated with the site activities. Consequently, when presenting a mechanical ventilation project, all of the participating parties and especially the contractor make a commitment to guarantee sufficient volumes (or airflow rates) of fresh (non-polluted and oxygenated) air and extracted (polluted) air in order to meet these limitations and maintain them in all conceivable site configurations. This article sets out the most important aspects of the implementation of a ventilation project from the initial design stage through to its application, discussing French legislation, ventilation principles, calculations and techniques with regards to underground construction sites. BASICS OF VENTILATION Mechanical ventilation studies are concerned with all of the site workstations and work phases which are sources of pollution and apply to all zones of the underground worksite with the goal of maintaining the concentration or composition of this pollution below the permitted levels and comply with the following three basic principles which are complementary to one another without being in contradiction. •,The first principle consists in eliminating or limiting as much as possible the emission of any polluting, irritant, or dangerous substances, by specifying appropriate construction techniques and equipment (use of electric motors, combustion engine equipment: filters, tanks, catalyzers, use of less polluting explosives, damping down dust with water or wetting products, damping down and diluting certain gases using water mists). •,The second principle is designed to capture residual polluting substances emitted close to the source in order to prevent them from spreading into the worksite atmosphere (extraction ventilation with ducting up to the source – upstream of the extractor fan – and use of downstream filters before expelling the polluted air to the exterior). •,The third principle involves accompanying the capture of the pollutants with additional blowing ventilation specific treatment of substances dissipated by and distant from the source of pollution (acceleration of the drift air flow in order to confine dust and better capture it, supply ventilation with ducting in order to dilute the gases emitted and discharge them to the exterior)."

Jan 1, 2016

By J. J. Ferreira, M. L. Thurston, I. L. Chinn, D. M. Rose

"Concerns about using microdiamonds for resource estimation have been raised by workers because multiple diamond populations exist in many parts of the mantle source region, small diamonds in kimberlite could be exposed to proportionately greater levels of resorption and modification, and euhedral microdiamonds could crystallize immediately prior to kimberlite eruption. This paper addresses these concerns; discusses the geology of the mantle, the principal diamond host rocks, and the impact of mantle processes; compares micro- and macrodiamond properties and features; and outlines steps to identify and mitigate the risk of diamond resorption and its impact on the diamond grade-size relationship.RÉSUMÉ Des travailleurs se sont interrogés sur l’utilisation de microdiamants pour estimer la ressource; en effet, de multiples populations de diamants existent dans plusieurs secteurs de la région source dans le manteau. Des petits diamants dans la kimberlite pourraient être exposés à des niveaux proportionnellement supérieurs de résorption et de modification; de plus, des diamants idiomorphes pourraient cristalliser immédiatement avant l’éruption de la kimberlite. Le présent article traite de ces questions, discute de la géologie du manteau, des principales roches-mères des diamants et de l’impact des processus dans le manteau, compare les propriétés et les caractéristiques des micro- et des macrodiamants et définit les étapes pour identifier et mitiger le risque de résorption des diamants et son impact sur la relation entre la taille et la qualité des diamants."

Jan 1, 2016

By Haipeng Li, Jacob Masliyah, Barun Gorain, Jian Huang, Qingxia Liu, Zhenghe Xu, AuTec Innovative Extractive Solutions Ltd.

"Froth flotation is widely used to selectively separate one or more minerals from an ore over a wide range of particle sizes with high efficiency. Bubble–particle attachment is one of the most critical steps in flotation. The objective of this project is to demonstrate the need for an innovative dual bubble generator to improve flotation efficiency. This dual bubble generator was designed to generate two different sizes (micron size and typical flotation size) bubbles. The micron size bubbles generated on the crevices of particle surfaces in venturi type of cavitation tubes enhanced the attachment of fine particles to the bubbles in conventional flotation systems. They also acted as a secondary collector, which has the potential to reduce operation cost and improve flotation recovery. The dual bubble generator was evaluated for a double refractory gold ore with 3g/t Au, 1.5 wt% TCM (total carbonaceous matter) and 0.7 wt% sulfides. The results were compared with those obtained using a commercial bubble generator. Compared with the commercial bubble generator, the dual bubble generator showed not only a higher gold recovery, but also an improved separation efficiency, demonstrating the potential of dual bubble generator in fine particle flotation.INTRODUCTIONFroth flotation has been widely used in mineral processing and waste water treatment. However, flotation has been proven inefficient for fine particle recovery although it becomes increasingly inevitable to process fine particles with the depletion of easy processing ores. The critical problem of fine particle flotation is the low attachment of fine particles to flotation size bubbles due to their low collision rate. Based on a commonly acceptable flotation model given by R =F*[Pc*Pa*(1-Pd)], the probability of bubble–particle collision (Pc), attachment (Pa) and particles detachment from air bubbles (Pd) collectively determines fine particle recovery (R) (Yoon and Luttrell, 1986). Since Pc = (3Dp/Db) where Dp and Db are diameters of particles and bubbles, respectively, bubble size and particle size impact the bubble-particle collision in opposite directions. It is evident that the probability of bubble–particle collision decreases with decreasing the size of particles, leading to a low recovery of fine particles. In this case, reducing the bubble size and/or increasing the apparent size of particles by fine particle aggregation are clear means to improve fine particle recovery."

Jan 1, 2016

By Mohamed Gamal, Bill Zietlow

"In oil fields that have been depleted with conventional surface oil wells but still contain significant reserves, an extraction alternative that has been constructed recently consists of a drilling gallery below the oil-bearing formation at the bottom of a 1,200-ft deep shaft where upward sloping wells are being drilled to allow oil collection by gravity. The gallery is 92-ft diameter with a flat ceiling supported by rock bolts and shotcrete structurally connected to the shaft liner, which doubles as a large tension support element. A special excavation sequence was implemented for the gallery to maximize arching in the stress above the large diameter gallery. The gallery was located in competent sandstone, constructed with sequential excavation methods, and designed with a 3D finite element model. Special consideration was given to optimizing the gallery location to take advantage of the geology for construction and support while giving good positioning to the well drilling equipment. BACKGROUND Brierley Associates was contracted to provide both design and construction management services for an approximately 1,165-ft deep, 18-ft excavated diameter vertical shaft that opens to a 92-ft diameter flat roof gallery. The geotechnical data for the site was based on information available from literature and from data obtained during core drilling and from in-situ testing in a 1250-ft deep borehole. Wire line coring was conducted using a HQ, 10-ft long core barrel with a mud-rotary drilling method through sedimentary bedrock. The geometry of the shaft and the bottom gallery is shown in Figure 1(a). GEOLOGIC SETTING AND STRUCTURAL GEOLOGY The stratigraphy at the site includes a series of interbedded marine limestone, shale, claystone, siltstone, sandstone, and chert units. Limestone and shale are the predominant lithologies in the upper approximately 675 ft, while the lower portion contains five distinct sandstone units and more abundant shale, claystone, siltstone, and coal than the upper zone. A cherty sandstone at a depth of 1,130 below ground surface (bgs) was encountered. At a depth of about 1,000 ft to 1,116 ft bgs, a non-marine sandstone unit was encountered. This sandstone is the hydrocarbon bearing layer. Joints and fractures observed in the limestone had dips ranging from 0 to 90 deg. from horizontal with joint and fracture surfaces that ranged from planar to irregular and smooth to rough. Several, near vertical shear planes with slickensides were observed with surfaces that were generally smooth and planar. RQD values for the limestone ranged from 0 to 100 percent but in general were good to excellent."

Jan 1, 2016

By Morgan M. Sears, lhsan B. Tulu, Ted M. Klemetti

"Why do some room and pillar retreat panels encounter abnormal conditions? What factors deserve the most consideration during the planning and execution phases of mining and what can be done to mitigate those abnormal conditions when they are encountered? To help answer these questions, and to determine some of the relevant factors influencing the conditions of room and pillar (R&P) retreat mining entries, four consecutive R&P retreat panels were evaluated. This evaluation was intended to reinforce the influence of topographic changes, depth of cover, multiple-seam interactions, geological conditions, and mining geometry.This paper details observations made in four consecutive R&P retreat panels and the data collected from an instrumentation site during retreat mining. The primary focus was on the differences observed among the four panels and within the panels themselves. The instrumentation study was initially planned to evaluate the interactions between primary and secondary support, but produced rather interesting results relating to the loading encountered under the current mining conditions. In addition to the observation and instrumentation, numerical modeling was performed to evaluate the stress conditions. Both the LaModel 3.0 and Rocscience Phase2 programs were used to evaluate these four panels. The results of both models indicated a drastic reduction in the vertical stresses experienced in these panels due to the full extraction mining in overlying seams when compared to the full overburden load. Both models showed a higher level of stress associated with the outside entries of the panels. These results agree quite well with the observations and instrumentation studies performed at the mine.These efforts provided two overarching conclusions concerning R&P retreat mine planning and execution. The first was that there are four areas that should not be overlooked during R&P retreat mining: topographic relief, multiple-seam stress relief, stress concentrations near the gob edge, and geologic changes in the immediate roof. The second is that in order to successfully retreat an R&P panel, a three-phased approach to the design and analysis of the panel should be conducted: the planning phase, evaluation phase, and monitoring phase."

Jan 1, 2016

By Dharmendr Kumar, Pradip, Beena Rai, Venugopal Tammishetti

"Due to rapid depletion of high grade Indian iron ores, there is a need to utilize low grade fines and slimes. However, these fines and slimes, in their current form, cannot be utilized in steel making due to their high alumina (6-10%) contents. Several beneficiation strategies such as gravity separation, magnetic separation, flotation and selective flocculation are currently being explored for the upgradation of low grade fines and slimes. In our previous work density functional theory simulations were employed to come up with selective flocculants for beneficiation of iron ore slimes. Our simulation results suggested that starch and guar gum are more selective towards iron minerals than other minerals present in the sample. Grinding of iron ore fines becomes necessary in some cases to achieve adequate liberation for removing alumina impurities in Indian iron ores. We have thus investigated effect of grinding of iron ore fines on its selective flocculation-separation.In the present work, we have taken natural iron ore fines from one of the Indian iron ore mines and ground it to -400 mesh (<37 microns) in dry and wet conditions. X-ray diffraction study confirmed the presence of minerals hematite, goethite, gibbsite and kaolinite in the sample. The fine ground samples were used in selective dispersion-flocculation study with corn starch and guar gum flocculants. It is interesting to note that even though the dry and wet ground samples possess almost similar particle size distributions, significant differences were observed in yield and grades of the concentrates thus produced. These differences may be arising due to the coating of alumina containing minerals on iron minerals. We have also studied the effect of addition of dispersant while grinding. Our study suggests that grinding conditions determine the efficiency of the separation process."

Jan 1, 2016

By Alfredo Valdivia, Hamed Nejad, Vincent Monaco, William Cao

"The East Side Access (ESA) CM005 Contract - Manhattan South Structures - consists of the installation of the waterproofing and final concrete lining for railroad tunnels, 3-Level Wye track turnout structures, segments of the Main Cavern Station, and a series of Ventilation Structures excavated beneath the existing Metro North Railroad (MNR) Grand Central Terminal. Several key team decisions made collectively by the Construction Manager (CM), Designer, and the Contractor has allowed the scheduled construction duration of 29 months to be maintained. These strategies include the use of alternate design and construction methods, including the use of pneumatically applied concrete lining and precast lining. This paper discusses these strategies, and illustrates how successful teamwork and cooperation during the execution of a large-scale construction project can lead to lowering costs, improving quality, and maintaining the overall project schedule. INTRODUCTION The East Side Access Project The Long Island Railroad (LIRR) currently transports commuters from Long Island into Manhattan, terminating at the already over congested Penn Station on the west side of Manhattan. Once completed, the ESA Project will provide LIRR commuters direct access to the east side of Manhattan underneath Grand Central Terminal. The ESA Project will help alleviate the congestion at Penn Station, which currently accommodate the NJ Transit, Amtrak, and LIRR lines; reduce travel time for LIRR passengers traveling to the east side of Manhattan and facilitate connections to the NYCT Subway System and Metro North Rail Road. The ESA Project includes building new tunnels and facilities under Manhattan and Queens. (See Figure 1).The Manhattan Alignment In the Manhattan segment of the ESA Project the excavation in hard rock of tunnels, cross passages, caverns and shafts has been completed by tunnel boring machines, drill and blast, and road header. The construction of the structural concrete final lining, interior structures and fit-out of the previously excavated caverns and tunnels are currently being performed under Contract CM005 Manhattan South Structures awarded to Michels Corporation and Contract CM006 Manhattan North Structures awarded to Frontier Kemper Constructors Inc. This paper focuses on the design and construction aspects of Contract CM005 which is the first ESA Contract in Manhattan to successfully construct concrete final linings in pre-existing excavated areas."

Jan 1, 2016

By Mahmoud Sepehrmanesh, Verya Nasri, Maziar Partovi

"This paper presents an assessment of the impact of tunneling and its associated risks on pile foundations located in the influence zone of tunneling operation. Tunneling in proximity of pile foundations introduces deformations in piles and in turn induces additional axial and bending forces. In modern mechanized tunneling, ground convergence is controlled through balancing the earth pressure at the tunnel face as well as applying pressurized bentonite through the shield. Reducing ground deformation can consequently lower the additional deformations and forces developed in the pile foundation and lessen the associated construction risk. In this paper, comprehensive detailed finite element modeling was performed to quantify the effect of the different parameters on induced forces in piles. Finite element models took into account the nonlinear behavior of soil and pile-soil interface. The modeling results are of practical importance in risk evaluation of tunneling in vicinity of pile foundations. INTRODUCTION Tunneling operation in congested urban areas becomes more frequent as demand for further utilizing underground spaces grows. In urban settings, it is not uncommon for tunnel designers to plan a tunnel route in close proximity to other structures to satisfy other competing objectives like raising the alignment to reduce excavation volume. Setting the alignment close to existing structures increases the risk involved in the project. It is the responsibility of the designer to thoroughly identify, assess, and mitigate all design risks involved. In this paper, we focus on the aspects involved in tunnel construction in proximity to existing pile foundations. Tunnel operations introduce deformation in the soil mass. Consequently, a pile located within deformation zone experiences extra forces as a result of the imposed deformation. The developed forces and bending moments can be in orders comparable with the pile capacity depending on the relative horizontal proximity of the tunnel and the relative depth of tunnel with respect to the pile length."

Jan 1, 2016

By M. H. Dehghanpoor, M. Zivdar, M. Torabi

"A hydrometallurgical route was developed to extract metals such as gold, silver, copper, and selenium from anode slime from Sarcheshmeh Copper Complex in Iran. For the extraction of copper by leaching, the anode slime was heated and stirred with 4 M sulphuric acid in the presence of oxygen. Optimal conditions for recovery of copper were temperature 80°C, mixing time 5 hours, and oxygen flow rate 2 L/min, resulting in a copper recovery of 94.47%. Silver and selenium were dissolved by leaching anode slime from which the copper had been removed with nitric acid. For gold extraction, anode slime was heated with aqua regia at 90°, and the gold then extracted with 2-ethyl-hexanol at a concentration of 0.5 M and phase ratio of 4. The extract was then stripped with soda solution at pH=10.5 and a phase ratio of 5. Finally, gold was recovered by precipitation with oxalic acid at a ratio of mass to volume 10 g/L. Total gold recovery was 80%. IntroductionDuring the electrorefining of copper, some metals are accumulated in the byproduct anode slime, which is an important source for recycling and recovery of these metals (Petkova, 1994). In this paper, a hydrometallurgical route is described for the recovery of precious metals from copper anode slime of Sarcheshmeh Copper Complex, which is located in southeastern Iran .Copper anode slime is black or gray powder with a particle size less than 200 mesh. Approximately 2 to 20 kg of anode slime is produced per ton of copper cathode. The slime is characterized by higher amount of Ag, Se, Pb, and Cu compared to other metals and a very low Au content (Khaleghi and Ghader, 2013).The copper anode slimes are composed of 11.69% selenium, 3.93% copper, 5.26% silver, 0.13% gold, and 45% barite, plus lead, tellurium, antimony, sulphur, and silica with small amounts of nickel, iron, zinc, and bismuth. Gold is one of the most important noble metals due to its wide applications in industry and economic importance, so recovery of gold from slime is more appealing than that of other metals. According to the World Gold Council (2013), the demand for gold has increased during the last decade. This increase is due not only to the increasing demands of the jewellery market, but also to the increasing demand for gold in industrial as well as medical applications (Ranjbar et al., 2014)."

Jan 1, 2016

By Tamara Nestorovic, Luan T. Nguyen

"With the aim to mitigate excavation risks and reduce the costs caused by tunnel boring machine (TBM) stoppage when tunneling under uncertain soil conditions, prediction ahead of the tunnel face has become an increasing interest in the tunneling community. Our research topic is concerned with developing effective concepts for nondestructive identification of geological anomalies ahead of the tunnel face by waveform inversion of reflected tunnel seismic waves. The authors demonstrate that this new technique is promising in providing tunnel engineers with an accurate image of the geological situation that the TBM is going to encounter thanks to the waveforms’ rich information about the geological structure that affects propagation, reflection/refraction and mode conversion behavior of the elastic waves. By setting up a 2-dimensional numerical model for simulation of tunnel seismic wave propagation influenced by a dip layer change ahead of the tunnel face, the authors show that the waveform misfit to be minimized by the inversion process is highly multimodal and therefore propose a hybrid stochastic optimization method that can quickly and robustly converge to the global minimum. DEVELOPMENTS IN TUNNEL ADVANCE EXPLORATION Conventional site investigation by drilling boreholes helps to draw a general image of geological structures along the borehole axes but that image is likely to misrepresent the detailed geological structure due to limited sampled locations. Due to high costs and restricted boring space which deep tunneling and tunneling under urban areas encounter, many industrial and academic research groups have had great interest in developing nondestructive ahead of the tunnel face prediction systems. That means only excitation sources and receiving sensors, which are usually placed on the ground surface or on the side walls or on the cutter head of the TBM, are used for acquisition of the measurement data. The recorded signals in the form of seismic or electromagnetic/ electrical waves, which travel through the geological structure or are reflected back from it, hold the signature of the geological structure of concern, such as geological layer changes, fault zones, erratic rocks, boulders, construction remnants, etc., and therefore can be used to reconstruct the spatial and material properties of those hidden geological structures. Most common nondestructive ahead-of-tunnel investigation systems to date are based on interpretation of reflected elastic/ acoustic waves (seismic waves) and analysis of electromagnetic/ electrical resistivity signals (Mooney et al. 2012). However, due to insufficient penetration depth and spread of signals generated by radar and geoelectric sources, the use of seismic waves for ahead of the tunnel face prediction (tunnel reconnaissance) is more preferable (Kneib et al. 2000; Bohlen et al. 2007)."

Jan 1, 2016

By Basar Arioglu, Jaeung Kim, Mehmet Öztürk, Jinmoo Lee, Dongho Lee, Taek-Kon Kim

"Istanbul Strait Road Tube Crossing Project (Eurasia Tunnel) includes 3.34 km of a bored double-deck tunnel under the Bosphorus Strait, at a maximum depth of 106 m from the sea level, and 1 km of twin NATM tunnels on the Asian side. The region’s variable geology, hydrology and propensity for seismic activity, combined with high water pressure and large-diameter/double-deck tunnel configuration, make the Eurasia Tunnel one of today’s most challenging and complex projects under construction. Due to the site’s proximity to the active North Anatolian Fault, the tunnel is designed to withstand a 7.5 magnitude earthquake. The tunnel penetrates through both the Trakya bedrock (on both European and Asian sides) and the alluvial sediments at the bottom of the channel. The tunnel is designed to accommodate differential displacements by introducing seismic/flexible joints at proper locations at the transition zones between rock and soft soils. Tunnel fire is also a significant design consideration for undersea tunnel due to that the rubber protecting it in close proximity of the seismic joint should resist a fire for long term safety and durability. This paper mainly focuses on the design for method of tunnel response analysis in transverse and longitudinal direction against seismic demands relating with the seismic joints. INTRODUCTION Istanbul Strait Road Tube Crossing Project (Eurasia Tunnel) will build and operate a roadway tunnel under the Borphorus connecting Kazlicesme on the European side and Goztepe on the Asian side, to provide additional road-access across the Strait and consist of three main parts as shown in Figure 1."

Jan 1, 2016

By C. Chongo, F. X. Paquot, C. Ngulube

"Over the last six years, the Kansanshi copper-gold mine has continued to process significant quantities of complex transitional mixed ores. Initially, the ore treated came predominantly from accumulated stockpiles. Subsequently, the feed source shifted primarily to freshly mined ore that generally showed less tarnish with better flotation kinetics, but with the downside of lower concentrate grades. A number of changes were made to improve the efficiency of the rougher circuit and quality of concentrate produced. These changes were as a result of initial mineralogical studies and laboratory flotation test work that were discussed at length in a previous paper1. Salient among the recommendations adopted as a result of previous work were increased circuit capacity and a modified configuration to increase the residence time and the number of sulphidization stages. These modifications were completed and commissioned in 2011. This, however, resulted in significantly low rougher concentrate grades and a below-specification final concentrate product. This was due primarily to higher mass pulls from the extended rougher bank with multiple concentrate discharge streams, and which necessitated an enlarged cleaning capability. The extra cleaning capacity came on stream in 2014. Of note was the development of a recovery model, based on the strong correlation between the total copper and acid-soluble copper ratio, as a tool for monitoring plant performance. IntroductionThe Kansanshi mine, the largest copper mine in Africa, is 80% owned by Kansanshi Mining plc, a subsidiary of First Quantum Minerals. The remaining 20% is owned by the state through the parastatal Zambia Consolidated Copper Mines Ltd (ZCCM). The mine is located approximately 10 km north of the town of Solwezi and 180 km to the northwest of the Copperbelt town of Chingola. The mine has been in commercial operation since 2005."

Jan 1, 2016

By William W. Edgerton, Moussa Wone, David H. Corkum, Carlton M. Ray

"The DC Clean Rivers (DCCR) Project is a 25 year, $2.6 Billion court ordered project to reduce combined sewer overflows (CSOs) discharging into the Potomac and Anacostia Rivers and Rock Creek, and also reduce flooding in the northern areas of the District of Columbia. Like all massive infrastructure programs, DCCR faced technical challenges, management challenges, risks of cost and schedule overruns, procurement challenges, and financing challenges. While DC Water is no stranger to large capital improvement projects (CIP), this CSO Program represents a once in a lifetime event for the Owner requiring the assembly of a single purpose team to implement. Some of the DCCR Project team’s most successful accomplishments to date are attributable to its introduction of early contractor involvement (ECI) to thoroughly vet the work from the perspective of the future constructors, development of functional baselines to share risks that are difficult to price and reduce reliance on geotechnical baseline interpretation during tunnel excavation, and attainment of financing through Municipal Century Green Bonds based on using design criteria of a minimum of 100 year life for the structures to establish intergenerational equity and fairness. This paper will discuss these innovations in detail and provide some sets of recommendations for the underground industry on when and how to use different approaches to better manage projects of this magnitude. INTRODUCTION The District of Columbia Water and Sewer Authority (DC Water) is an independent multi-jurisdictional authority that was established in 1996. Its primary mission is to provide water distribution services to more than 640,000 residents in the District of Columbia (District), and sewer treatment and disposal to 1.6 million residents of the District, Montgomery and Prince George’s counties in Maryland and Fairfax and Loudoun counties in Virginia."

Jan 1, 2016

By Magnus Evertsson, Johannes Quist

HPGRs have since introduced in the 1980s (Kellerwessel, 1993; Schönert, 1988), now become integral comminution units at several minerals processing plants around the world. Even though a lot of the initial issues concerning performance, availability and wear have been addressed and solved there are still phenomena and aspects which can be improved and understood further. Schönert and Sander (2002) presented experimental results and a mechanistic model including the internal force dynamics between the rollers and the compacted bed. They derived expressions for the pressure distribution involving most of the influencing terms and effects. However, in order to solve the differential equations several of the terms vanish by assumptions. The Schönert and Sander model reflects the experimental data in many aspects but the predicted shear force distinctly deviates from the experimental results at the angular position of the peak pressure level. This finding suggests that the particle to particle interaction and breakage process in the different zones seen in Figure 1 are complex and difficult to model using analytical models. A numerical modelling approach using DEM does not require the same amount of assumptions and simplifications of boundary conditions. Hence such modelling may provide further knowledge and vital understanding. In this paper the breakage process is simulated in order to investigate the shear slip behaviour and how it relates to different operating variables. A laboratory scale HPGR corresponding to the experimental setup used by Schönert (2002) have been modelled in EDEM (DEM-Solutions). The bonded particle model (BPM) is used for modelling quartz particles (Potyondy, 2004). The breakage model strength parameters are calibrated against interparticle breakage experiments in an Instron 400RD compression device. The contact model parameters are calibrated using calibration methods developed by Quist (2015). The floating roller dynamics are modelled using a spring-damper system. Results present insights regarding the interparticle slip behaviour as well as the frictional tangential force distribution on the rollers. The simulated roller pressure distribution shows good correspondence with previously reported findings in the literature.

Jan 1, 2016

By Scott Lewis, Andrew Kositsky

"INTRODUCTIONThe South Napa Earthquake of 2014 caused ground motion at numerous reinforced concrete-lined (shotcrete-lined) winery tunnels in Napa County and Sonoma County, California. The occurrence of seismic ground motion at these tunnel complexes, known as wine caves, presented an opportunity to reevaluate seismic performance of reinforced concrete and reinforced shotcrete lined tunnels. The authors of this paper updated the most recent comprehensive compilation and evaluation of case studies by Power and others (1998), which correlates peak ground acceleration (PGA) at tunnel sites to damage. For this update, the authors evaluated the seismic performance of 31 wine caves near the South Napa Earthquake epicenter; including some of the 90 wine caves they designed since 1991, some caves designed by others, and additional caves constructed by contractors that they frequently work with. Tunnel designers can use the new data presented in this paper to help evaluate the usefulness of detailed seismic design analyses. THE SOUTH NAPA EARTHQUAKE The South Napa Earthquake occurred at 3:20 AM Pacific Daylight Time on August 24, 2014. Figure 1 shows the approximate location of the epicenter, the measured/estimated PGA contours, and the location of wineries with wine caves added to the database where the PGA was at least 0.2 g. The epicenter was along the West Napa fault, about 5 miles south-southwest of downtown Napa, California. The earthquake moment magnitude was 6.0, and measured/estimated PGAs were up to about 0.7 g. The duration of strong shaking was about 10 seconds. This earthquake was characterized by right lateral strike-slip fault movement, ground surface rupture, and after slip at the ruptures. Increased surface water flows were observed at seven creeks after the earthquake. Groundwater level rises of up to 5 feet were observed in Sonoma County wells after the earthquake. The earthquake was the largest seismic event in the San Francisco Bay Area, which includes Napa and Sonoma Counties, since the 1989 Loma Prieta Earthquake. The Napa event caused an estimated $400 million in damage. This damage included moderate to extensive structural damage to older commercial buildings and to some newer buildings in downtown Napa. This damage resulted from ground motions, subsequent fires, and failed underground utility systems."

Jan 1, 2016

By Junhyun Choi, Allan Gomez-Flores, Chonbuk National University, Siyoung Q. Choi, Gahee Kim, Seungkon Kim

In this study, to confirm the effect of depletion attraction on the flotation, we theoretically and experimentally investigate the effect of the depletion attraction force on flotation. While varying the concentration of the depletion agent (polyethylene glycol), three different systems are studied: pure malachite, pure silica, and a 1:1 mass ratio of malachite and silica binary system. We find that recovery increases significantly as the concentration of the depletion agents increases for all three systems, as the depletion agent facilitates the adsorption of the particle on the bubble surface. However, the recovery suddenly decreases in a certain concentration range, which corresponds to the onset of the decreased surface tension when high concentrations of the depletion agent are used. This non-monotonic overall recovery trend implies the surface adsorption of the depletant on a surface. The decreased surface tension of the air/water interface suggests that the recovery rate is lowered due to the adsorption of the depletion agent to the bubble surface, acting as a polymer brush. Based on our observations, we conclude that the depletion force can greatly improve particle adsorption, as predicted in the accompanying theory paper, while simultaneously the adsorption of the depletion agent on the bubble surface plays an important role because it hinders particle adsorption. We also perform experiments in the presence of a small amount of a collector, sodium oleate. An extremely small amount of the collector leads to the increase in the overall recovery, which eventually reaches nearly 100 percent. Nevertheless, the grade worsens as the depletant provides the force to silica particles as well as target malachite particles.

Jan 1, 2016

By Michael Murphy, Khaled M. Mohamed, Berk Tulu

"Failures of coal ribs are major hazards in underground coal mines. For the period of 2010 to 2014, rib falls were the leading cause of groundfall fatalities and accounted for 35% of all groundfall-related fatalities. Currently, the National Institute for Occupational Safety and Health (NIOSH) is conducting a research project to develop an engineering-based design methodology for rib control in underground coal mines to reduce rib fall accidents and fatalities. Numerical models can be used as part of the design methodology provided the models are appropriately calibrated and verified.This paper presents a coal rib model to simulate the mechanism of coal deformation and fracturing that can lead to stress-driven rib falls. The proposed coal rib model was calibrated against published data from an instrumented rib site at the West Cliff Mine in Australia. Fracturing of the coal rib was defined by critical VALUES (of plastic shear strain of the coal material and rib displacement. A critical plastic shear strain of 2.8% and a sudden increase of rib displacement of 30 to 45 mm were sufficient to develop a fracture plane in the rib model. Accordingly, a discontinuous rib deformation was achieved and it compared favorably against field monitoring data.INTRODUCTIONCoal ribs are the vertical walls of coal formed when entries are developed in a coal bed. Failures of coal ribs are a major hazard in underground coal mines. Furthermore, failing ribs can contribute indirectly to roof and floor instability by increasing opening widths across intersections and entryways. Over the last 18 years, there has been a continual occurrence of injuries and fatalities in underground coal mines due to rib falls. For the period of 2010 to 2014, rib falls (excluding longwall face failure and bursts) were the leading cause of ground fall fatalities and accounted for 35% of all groundfall-related fatalities (MSHA, 2015)."

Jan 1, 2016

By L. Yuan, A. Smith

"NIOSH’s mine fire simulation program, MFIRE, is widely accepted as a standard for assessing and predicting the impact of a fire on the mine ventilation system and the spread of fire contaminants in coal and metal/nonmetal mines, which has been used by U.S. and international companies to simulate fires for planning and response purposes. MFIRE is a dynamic, transient-state, mine ventilation network simulation program that performs normal planning calculations. It can also be used to analyze ventilation networks under thermal and mechanical influence such as changes in ventilation parameters, external influences such as changes in temperature, and internal influences such as a fire. The program output can be used to analyze the effects of these influences on the ventilation system. Since its original development by Michigan Technological University for the Bureau of Mines in the 1970s, several updates have been released over the years. In 2012, NIOSH completed a major redesign and restructuring of the program with the release of MFIRE 3.0. MFIRE’s outdated FORTRAN programming language was replaced with an object-oriented C++ language and packaged into a dynamic link library (DLL). However, the MFIRE 3.0 release made no attempt to change or improve the fire modeling algorithms inherited from its previous version, MFIRE 2.20. This paper reports on improvements that have been made to the fire modeling capabilities of MFIRE 3.0 since its release. These improvements include the addition of fire source models of the t-squared fire and heat release rate curve data file, the addition of a moving fire source for conveyor belt fire simulations, improvement of the fire location algorithm, and the identification and prediction of smoke rollback phenomena. All the improvements discussed in this paper will be termed as MFIRE 3.1 and released by NIOSH in the near future INTRODUCTION The MFIRE program, originally developed in the 1970s by the U.S. Bureau of Mines (now the Office of Mine Safety and Health Research (OMSHR) at the National Institute for Occupational Safety and Health (NIOSH)) and Michigan Technological University, has been a mainstay in modeling of the mutual influences between a fire and the mine ventilation system during an underground mine fire. Several update versions have been released over the years, including MFIRE 1.27, 1.29, 1.30, 2.0/2.01, 2.10, and 2.20. The MFIRE program logically comprises four parts: (1) a conventional network calculation, where it performs the basic network balancing without considering heat or mass transfer; (2) a temperature calculation to establish the reference temperature distribution before a non-steady state (transient-state) simulation; (3) a transient-state simulation that follows changes in ventilation step-by-step to produce a continuous description of the temperature distribution, smoke, and contaminant spread through the ventilation system during a fire event; and (4) a quasi-equilibrium simulation to predict the state of the ventilation system after a relatively long period of time (defaulted as 5 hours in MFIRE) as the fire reaches a quasi-steady state. In summary, MFIRE is a computer simulation program that performs normal ventilation network planning calculations and dynamic transient-state simulation of ventilation networks under a variety of conditions including the influence of natural ventilation, fans, fires, or any combination of these (Chang et al., 1990)."

Jan 1, 2016

By C. J. Hartley

"Scandium oxide can be recovered as a by-product from process streams in a number of chemical and metallurgical plants including TiO2 sulphate pigment, Ni/Co laterite, zirconium oxychloride and uranium operations. The feed materials available for processing can be either mid or end of process streams containing many species in solution. This paper describes the strategies available to limit coextraction of elements into scandium containing streams from TiO2 pigment production and the removal of these elements to deliver high purity scandium oxide.A critical part of process development is to work within the constraints of the main process in terms of introducing new unit processes and producing minimal additional process intermediates and residues. This requires flexibility in designing flowsheets and plants to find novel process routes that avoid production of intermediates and/or the introduction of reagents that can compromise the main process operations.Bloom Energy has developed novel solvent extraction processes for the extraction and refining of scandium oxide that minimise impacts on core process streams within TiO2 pigment plants. The additional unit processes are designed to have minimal contact with pigment plant process streams to produce a concentrate that is refined to nominal 3N purity scandium oxide in a simple, small scale commercial plant."

Jan 1, 2016