Search Documents

By Carl-Oscar Nilsson, Åke B. Nilsson

"The embankment dam at Storfinnforsen is 23 m high and was completed in 1954. The dam has an impervious zone with timber sheet piles and a support fill of glacial till. The pore water pressure in the downstream shoulder has during recent years increased due to deterioration in the sealing function of the timber sheet piling. There is a concern that the high pore water pressure in the glacial till will cause internal erosion initiating at a thin coarse transition layer between the glacial till and the rock fill along the downstream toe. As a remedial action in order to improvement of the leakage resistance a supporting berm of coarse rockfill against the downstream slope of the dam was constructed in year 2013. In addition a new impervious seal in the centre of the dam e.g. a diaphragm wall was considered. However, after further studies and a trial stretch of 40 drains each 20 m long and diameter 0.3 m an alternative with vertical drilled drains in the downstream support was selected. A contract has now started up to drill in a similar way to treat the full length of the dam with drains. The work is in the planning to be completed in 2016.Dam ConstructionStorfinnforsen Embankment Dam was put into operation in 1954. The dam is 330 m long and maximum height is approximately 23 m. The dam is constructed with a central core zone and supporting zones of earth and rockfill on the upstream and downstream sides giving an almost symmetrical cross-section about the dam axis, see Fig. 1. The upstream slope is 2H:1V down to el. 270 and 2.5H:1V below. On the downstream side the slope is 1.75H:1V down to +269 and 2H:1V below. The core zone consists of a timber sheet pile wall with a Zone 5 of glacial till, approximately 2 m wide, adjacent to the wall on the upstream side."

Jan 1, 2016

By Behzad Khorshidi

"The ultimate objectives of the post-tensioned strands are to connect the precast segments into a ring and provide pre-stress in the tunnel circumference. The method involves inserting the strand through the preliminary embedded duct in the precast concrete segments and then tensioning the strand by jack and fastening it. The post-tensioned strand eliminates the necessity of bolt connections between the segments and may reduce the labor cost and increase speed of lining construction. Pre-stressing of the segmental lining reduces the steel reinforcement or fiber volume in precast segments and/or thickness of the precast segments which would result in reducing the manufacturing cost of them. Pre-stressing would reduce cracking and increase water tightness, and would provide smooth intrados due to eliminated bolt joints and pockets in the tunnel lining. Pre-stressing would increase resistance to internal pressures as well. Further, this system could work very well structurally in tunnels with squeezing rock or tunnels with high seismic loadings. INTRODUCTION OF THE METHODPost-tensioning is commonly used in the construction of bridges, large buildings, nuclear power stations, and water tanks but its utilization in tunnels is still in its infancy.The precast pre-stressed concrete segmental lining can be used for shield tunnels. It provides a reinforced lining ring by the following construction stages and as shown in Figure 1:1) Segments to be assembled by TBM to complete a full ring2) Steel strand to be inserted through embedded duct (sheath) within the segments3) The strand to be tensioned by Jack after anchorage of the other end4) The strand to be fastened after reaching required tension load5) The horizontal strands (if necessary) to be installed, tensioned and fastened6) The recesses and gap between strand and duct to be filled by groutingFurther, Figure 2 shows an unbonded post-tensioning strand model; Figure 3 shows an anchor sample (Xanchor); Figure 4 shows a duct (sheath) and anchor within reinforcement; Figure 5 depicts the posttensioning of a strand by jack; and Figure 6 is an image of the Midorigaoka Trunk line tunnel in Sagamihara, Japan which was constructed using this system."

Jan 1, 2016

By Aditya Ayithi, William G. Ryan, Dean Herbst

"For rock socketed drilled shafts, it is a common practice not to include the frictional resistance of overburden soils into the nominal capacity estimation. The primary reason often being cited is “overburden soils resistance is negligible compared to that of rock socket resistance.” However, in certain geological conditions, where the rock layer is located at greater depths, friction resistance from overburden layers can be significant. In addition, at such great depths, shaft drilling becomes very complicated and expensive. In these situations, considering the resistance of the overburden layers can be an economic alternative.This paper presents a case study of an Osterberg cell (O-cell) load test conducted on a 161.8 feet long and 78-inch diameter instrumented test shaft. Based on initial designs, a 72-inch diameter rock socket of lengths 23 and 26 feet was required to provide a LRFD factored friction resistance of 3,200 kips. The load test results revealed that the material in the 72-inch diameter socket does not represent a true rock. However, the test results also proved that the factored friction resistance of overburden layers is greater than the required design resistance. Based on the load test results, it was decided to allow the overburden soils frictional resistance to be considered in the shaft design, resulting in significant economic savings.INTRODUCTIONRock socketed drill shaft design guidelines of various State Department of Transportation (DOTs) agencies allow friction and/or end bearing resistance of only the rock socket portion into the design capacity estimation. It is typical to neglect the frictional resistance of overburden soils. However, in certain geological conditions where the rock layer is at greater depths, friction resistance of the overburden soils can be significant. In this case the friction resistance of overburden soils was verified via the specified instrumented O-cell test program and then used as part of the design capacity.PROJECT DESCRIPTIONAs part of I-29 improvement project, Iowa Department of Transportation (Iowa DOT) planned to replace the dual four lane bridges that cross the Floyd River in Sioux City, Iowa with dual six lane bridges (Fig. 1). Expected benefits from this improvement include improved safety, traffic operations and roadway infrastructure conditions.BRIDGE SUBSTRUCTUREThe project consists of two individual bridges; a new south bound bridge and a new north bound bridge. The south bound bridge is 646-ft long and the north bound bridge is 644-ft long. Both are six-span, pretensioned and pre-stressed concrete beam bridges of varying width. Bridge foundations were designed such that the abutments of both bridges will be supported on driven steel piles and the bridge piers will be on drilled shaft foundations."

Jan 1, 2016

By V. I. Ryaboy, V. P. Kretov, I. V. Ryaboy, E. D. Shepeta

This paper studies the features of known and newly synthesized dialkyldithiophosphates and reagents with thioamide groups when separating copper-containing and arsenic-containing minerals in the flotation of skarn-scheelite-sulphide ore at the Primorskaya concentration plant. The optimization of dialkyldithiophosphate collectors was based on the study of their surface activity at the liquid-gas interface and estimated hydrophobic abilities. The flotation experiments show that the selectivity of action of the reagent increases with an increase of its surface activity and a reduction of hydrophobic ability when separating chalcopyrite and arsenopyrite. IMA-225-5 was proposed as a more efficient dialkyldithiophosphate collector, which increases the recovery of copper by 2.8% compared to the industrially used collector IMA-I413. Selection of the optimal structure for reagents with thioamide groups (derivatives of thionocarbamate and thiourea) was carried out according to their acidity and the presence of hydrophilic particles in their structure. Calculations were performed depending on the pH of the solution of chalcopyrite to determine the optimum reagent sorption and to further optimize the structures of these reagents. The tests with reagents with thioamide groups show an increase in copper recovery by 3-4% together with a significant increase of arsenic content compared to IMA-225-5. As a stronger collector with thioamide groups, it was recommended to use sample 234, which belongs to the thiourea derivatives. IMA-225-5 was recommended for industrial tests at the Primorskaya concentration plant. Thus, this study has shown that using dialkyldithiophosphate is more appropriate if it is necessary to increase the selectivity of separation of copper-containing and arsenic-containing minerals, and using reagents with thioamide groups, or their combinations with dialkyldithiophosphates, is more appropriate if it is necessary to increase the recovery of copper or the quality of copper concentrate with less selectivity of the process.

Jan 1, 2016

By T. Ellis, J. Gagnon, L. Webb, M. Burr, D. Kakengela, D. Evans, A. Mirza

Lead-based alloys are used as the primary anodes for electrowinning from sulphate-based aqueous systems. Lead anode technology has evolved over the years, migrating from pure lead and lead-antimonial alloys to the present-day lead-calcium-tin alloys for copper electrowinning and leadsilver alloys for zinc electrowinning. Anode technology has also migrated from cast to rolled microstructures in search of improved mechanical properties and higher corrosion resistance. Although great strides have been made in the development of new alloys and production processes, the industry still has unresolved issues related to untimely corrosion, which limits anode life and may lead to higher contaminant levels in the metal being produced. Lead anodes corrode because of the difference in the chemical/electrochemical potential across the microstructural features of an anode. Given a very high purity material, we find that the grain boundary areas corrode significantly faster than the rest of the grain. A balance of alloying element selection and microstructural design allows the grain boundary area to be engineered, thus minimizing grain boundary corrosion. However, operational issues can lead to unexpected corrosion behaviours that we will discuss moving forward. The comments in this work, although directed toward copper electrowinning, can be extended to similar phenomena in other metals electrowon from sulphate media (i.e., zinc, nickel, cobalt, manganese). The life cycle of electrowinning anodes depends on tankhouse operating conditions and maintenance of the anodes, including cleaning and straightening. This paper will focus on the operational aspects of maximizing the utilization of lead anodes for base metals electrowinning.

Jan 1, 2016

By K. Swedburg, M. Samuels

"The New Afton concentrator was commissioned in June 2012, reaching the design milling rate in September 2012. By late 2013, through a campaign of optimization and de-bottlenecking, it was recognized that the installed plant was capable of greatly exceeding the design throughput of 11,700 tpd. Because the value of the metal contained (by increasing the plant feed rate) exceeded the offsetting losses of copper and gold recovery (as the operation moved to a coarser grind), the concentrator feed rate was strategically increased with support of New Gold, while the operations team was given a mandate to evaluate, and then implement, flow sheet options that could re-establish the original design criterion grind target and achieve the corresponding improved recovery. Broadly, the two options implemented were the addition of a tertiary grinding stage consisting of Metso Vertimill® prior to rougher flotation (in order to address the grinding required at increasing throughput by increasing the power), and the addition of three Woodgrove Staged Flotation Reactors (SFR) added to the cleaner circuit after regrind of the rougher concentrate (to address the increased mineral loading to the cleaner circuit). Through test work, it was anticipated that the SFRs would be capable of achieving final concentrate grade in a single pass without the integration of recirculating loads, a strategy sometimes referred to pre-cleaning. This paper describes the expectations generated for the Woodgrove SFR unit operation through pilot plant testing on site, and compares those results with the performance of the expanded circuit that exceeded the original design criterion of P80 160 µm, which was commissioned in the second quarter of 2015.INTRODUCTIONThe New Afton concentrator, located near Kamloops, BC Canada, commenced operation in June 2012. The mill achieved the design throughput of 11,000 tonnes per day average during the month of September 2012 and, following various operational optimization efforts (O’Hara et al, 2015), achieved the design p80 grind size of 160 µm at the design milling rate in July 2013.During August 2013, trials were carried out to determine the throughput rate limits of the mill circuits and to evaluate mill metallurgical performance at higher rates. Milling rates up to 15,500 dmt per 24 hours were achieved during this trial, demonstrating potential capability for sustained milling rates exceeding the nominal design capacity. As was expected, the higher milling rates resulted in a coarsening of the grinding circuit product size, and resulted in marginally lower recoveries in the rougher flotation circuit. Despite the lower recoveries, the higher milling rates resulted in higher metal production and the financial analysis favored running at rates of at least 13,000 tonnes per operating day, with the higher cash flow in the near term offsetting the value of metal production loss at the end of the mine life (due to the short term increase in the rate of reserve depletion). Milling rates were sustained above 13,000 tonnes per day through the second half of 2013, and increased above 14,000 tonnes per day by mid-2014 (Figure 1)."

Jan 1, 2016

By J. Sikamo, A. Mwanza, C. Mweemba

"The Zambian copper mining industry as we know it today had its genesis in the 1920s. Consistent private sector-driven investment in the industry over a period of over 50 years in exploration, mine development and operation, development of minerals processing facilities, building of infrastructure for pyrometallurgical and hydrometallurgical processing, with attendant support facilities, including building of whole new towns, resulted in copper production rising to a peak of 769 000 t in 1969, providingover 62 000 direct jobs. The industry was nationalized in 1973 and remained in government hands for just over 24 years. During this period, the industry experienced a serious decline in production levels, reaching the lowest level in the year 2000 when production was 250 000 t. An average of just under 2000 jobs were lost every year in the 24-year period, reaching just over 22 000 direct jobs in 2000.Following the return of Zambian politics to pluralism and liberalized economic policies, the government decided to privatize the mining industry. The process started in 1996 and by the year 2000 all the mining assets had been privatized. The new investors embarked on serious investment to upgrade the assets and to develop greenfield mining projects. Fourteen years later and after more than US$12 billion investment, production levels increased year-on-year to a peak of 763 000 t in 2013 with direct jobs reaching 90 000.This paper discusses the impact of the mining industry in Zambia on the economy in areas such as employment, support for other industries, direct contribution to the national gross domestic product (GDP), foreign exchange earnings, and social amenities. The paper also focuses on the performance of the mines during these periods vis-à-vis mineral availability, mineral grades and complexity, new technologies, and human capital. This is looked at particularly in the light of current challenges the industry is facing. Suggestions are proposed on how the industry can be nurtured to continue being a major driver for the Zambian economy and a major player in the international copper mining business."

Jan 1, 2016

By T. Faulkner, S. A. Richards

"Classic engineering economics provides the mining engineer with a fundamental approach to choosing between capital spending alternatives. This approach has been heavily used over the years and is an accepted technique for most investment decisions. There is a shortcoming that I have run into over the 15 year period when I worked in business planning roles. The classic time value of money approaches such as Net Present Value, Return on Investment, and Internal Rate of Return provide good estimates, but the input assumptions may fall short of describing the real material differences required by these analysis techniques. If the cost benefit analysis is defined solely on the improvement of the item being replaced or improved, the true profitability of the decision may be overestimated. Productivity improvement based capital projects can yield more accurate forecasts when conducted in concert with a “bottleneck analysis”. INTRODUCTION A review of the Theory of Constraints, (Goldratt, Cox, 1984) Lean, (Womack, 2003) (Rattner, 2006) and Six Sigma (Cryger, DeFeo 2015) lead us to recognize that these process improvement methodologies are oriented to the manufacturing process. These systems generally involve a factory that the material moves through on the way to becoming a final product. The mining challenge has many similarities to manufacturing once the ore has been won and made ready for processing. Before that point, however, the process is somewhat inverted while the ore is being won. Instead of the material moving through the factory, the factory is moving through the material. The Theory of Constraints (TOC) was used in an underground context by Baafi, Cai and Porter at 2015 APCOM, but even this groups’ analysis did not carry the concept from mining to shipping of the final product. There can be spatially distributed data that can affect the mining throughput constraints, some of which can be determined from exploration results. Identifying constraints can lead us to mapping productivity bottlenecks on future mining. Knowing this may improve decision making by eliminating one of Jim Fishbein’s three deadly sins of strategic planning: incomplete planning. When evaluating capital investment alternatives you should evaluate the impact of any proposed improvements on the entire operation. At the core of any mining system is the materials handling system. This can be typically expressed as the system that handles the raw material from the “face” through processing and then handling the finished product as well as the waste material. A “Bottleneck Analysis” is an investigation into the factors limiting a material handling system’s productivity (Goldratt, Cox, 1984). Mining material handling systems are usually composed of several linked components such as draglines, shovels, loaders, hydraulic excavators, continuous miners, longwalls, highwall miners, bucket wheel excavators, LHDs, feeders, conveyor belts, stockpiles, crushers, processing plants with various circuits, and waste handling systems. Each of the aforementioned components has a slightly different throughput capacity. When these are linked in series, the one with the lowest throughput capacity limits all of the others, creating the bottleneck for the system. Every material handling system has a bottleneck. In the mining environment, a subtle, but very significant phenomenon may also occur. The bottleneck may change as a result of a change in the raw feed qualities, face recession, overburden depth, digability, learning curve, and many others factors which may be derived from the drillhole data. These parameters often change as a function of the location in the reserve base, and may also vary with time."

Jan 1, 2016

By M. Raffaldi, J. Johnson, M. Stepan, D. Benton

"The Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD), is continuing its High-Energy High-Displacement (HEHD) testing of field-scale shotcrete panels. A test program was developed to determine the relationship between applied force, displacement, and energy for both unreinforced and reinforced shotcrete panels. Reinforcement options consisted of synthetic macro-fibers, sprayed polyurea liners, chain-link fence, welded-wire mesh, and combinations of these products. During testing, photogrammetry was used to measure the geometric changes of the panels, including volume changes and panel cracking. These measurements were correlated with the load and displacement data, allowing visual observation to be related to the applied force and displacement. The test results provide a comparison of the mechanical performance of the various panel types and can be used by the practicing engineer to evaluate installed support based on visual observation of cracking and deformation. Visual assessment of the loading cycle and strength capacity of shotcrete in underground excavations will improve mine safety by providing a means to quantify the stability of installed shotcrete support. INTRODUCTION The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD) is continuing research on the behavior of shotcrete when used as the surface support component in mining ground support systems. Ground control safety often depends on supporting, or at least containing, the ground between the rockbolts. Shotcrete and mesh, in various combinations and with other components, are often used to accomplish this (Figure 1). Maintaining support pressure during ground deformation is key to the performance of these systems, and to ensuring miner safety. However, the toughness of a ground support system–the ability to maintain strength over large deformations–is difficult to quantify. Researchers at SMRD have responded to this deficiency by designing a full-scale test device, described previously by Martin et al. [2015a], and beginning a testing program to assess the behavior of shotcrete surface support reinforced with a variety of products including: fibers, chain-link mesh, welded-wire mesh, spray-on polyurea liners, and combinations of these products. This paper presents the findings of these tests."

Jan 1, 2016

By J. Kemeny, J. Lyons-Baral

"Point cloud technology is now an indispensable tool in geological and geotechnical data collection, interpretation and analysis. Open pit and underground mines of all sizes are regularly collecting point cloud data as Laser Scanning (LiDAR) and Photogrammetry surveying devices have finally become affordable and the workflows fast and efficient. Past challenges of large data processing and manipulation are gone with recent technological advancements in computer hardware and software. These innovations reduce file sizes, ease rendering requirements and allow for the implementation of real-time 3D viewers and surface meshing tools. With its ability to remotely (safely), rapidly and accurately extract large quantities of georeferenced and 3D-oriented data, point cloud technology provides numerous applications to the geomechanical field. The list of uses is continuously growing, so this paper specifically focuses on digital outcrop modeling and digital terrain engineering. INTRODUCTION Point Clouds The high-resolution and increasing availability of point cloud technology is rapidly improving open pit and underground mines’ investigation, interpretation and characterization of site geology and rock mass properties (Kemeny et al., 2015; Lyons-Baral, 2012). LiDAR and photogrammetry are common remote sensing methods employed to measure the coordinates of surfaces in three dimensions (3D), providing the X, Y and Z locations, and typically the reflective intensity and/or the visible three-band color of each point (Figure 1). LiDAR uses either a time-of-flight or phase-shift measurement of a laser beam reflected off targeted surfaces and received back into the device. Photogrammetry generates point clouds by merging multiple overlapping photographs and uses stereographic plotting to define the locations of object points in 3-D space. These methods can be deployed from airplanes, unpiloted aerial systems (UAS or drones), tripods, land vehicles, and even in a mobile backpack shown in Figure 2. RADAR, Total Station-Prism and other remote sensing systems also offer very precise “point clouds”, but this paper does not address these due to their higher cost and lower versatility and mobility. Technology In the past few years point cloud acquisition device prices have dropped significantly, devices have become lighter, smaller and easier to operate, and processing and utilizing the data has also become faster and easier. Device size improvements include mobile backpacks (Figure 2) and handheld mobile LiDAR (CISRO, 2014), allowing mobile scanning in tight spaces both above and below ground or inside and outside of man-made structures. Airborne data acquisition options have expanded dramatically with the spread of UAS technology as seen in Figure 3 (Hexagon Geosystems, 2015). Once UAS usage regulations are sorted out, these versatile machines will be everywhere, offering high resolution coordinate scans, imagery and other remote sensing. While backpacks and handhelds allow access to tight quarters, UAS permit rapid data capture from narrow to broad areas with multiple perspectives reducing data “shadows.”"

Jan 1, 2016

By E. Ghali, A. D. Bas

"Treatment of oxide, e.g. roasted gold ores has received relatively less attention than sulphidic ones and recently, handling of oxide gold ores is becoming essential. In this study, the influence of roasted gold ore (RGO) slurry (at 35% solid ratio) on the electrochemical dissolution of gold has been examined using pure gold and iron oxide minerals (hematite, maghemite, and magnetite) as disc electrodes by zeroresistance ammeter mode either in one or two separate containers. The presence of slurry decreased galvanic currents, i.e. corrosion rates due to the release and increase in the amount of soluble and/or insoluble species that could retard further the anodic behaviour of gold. Higher galvanic currents were observed in two separate containers than that in one container indicating the primary importance of galvanic interactions. SEM-EDS results observed iron hydro/oxide coatings on gold surface in case of magnetite test. However, in case of RGO electrode it is not a perfect passivation, although somewhat decreasing trend was observed on gold dissolution. These findings have revealed that passivation is not only a laboratory phenomenon, but also it could be responsible for the slowdown of gold dissolution in industrial practice.INTRODUCTIONThe cyanidation of gold is an electrochemical corrosion process thus; the dissolution of gold can readily be studied by electrochemical techniques. The outcome/summary of previous electrochemical studies of gold leaching can partially be summarized as follows: Filmer (1982) and Lorenzen and van Deventer (1992) reported the negative effect of pyrite and pyrrhotite on gold leaching due to the galvanic interactions; Aghamirian and Yen (2005) studied gold galvanic corrosion in presence of sulphide mineral electrodes only in one cell using zero-resistance ammeter (ZRA) mode; Dai and Jeffrey (2006) discussed, individually, the anodic and cathodic behaviours between gold and sulphide minerals, and Azizi et al. (2010, 2011) used a bed reactor to examine the influence of sulphide minerals on gold dissolution in one and two separate cells. Accordingly, a slowdown in gold leaching has generally been attributed to the passivation phenomenon, although the indication of this phenomenon is still an undergoing debate. For instance, Mrkusic and Paynter (1970) identified the passivation as the film formation of dissolved species from calcine, Crundwell (2014) explained passivation, in the case of corrosion of metals, as the formation of a layer which is composed of a new chemical species on the mineral surface and this layer inhibits or blocks further reactions. He suggested that passivation is related to the oxidation of the metal, and the formation of a passive layer that retards the rate of dissolution by several orders of magnitude. Consequently, galvanic interactions, passivation phenomena, or combinations of them are considered significant electrochemical factors affecting gold dissolution (van Deventer, Reuter, Lorenzen, & Hoff, 1990; Azizi, Petre, & Larachi, 2012). It is important to note that generalizing the influence of a mineral/metal on gold dissolution may not be correct in all cases, since contrary behaviours/results (for pyrite) have been observed (Aghamirian & Yen, 2005). Therefore, electrochemical study of gold is still a subject of research and need to be examined further in detail."

Jan 1, 2016

By Markus Thewes, Mario Galli

"INTRODUCTIONProject-related studies showed that lab tests are a helpful tool for the planning of EPB tunneling and soil conditioning in cohesionless soils. This type of ground commonly represents the extended application range for EPB shields, which demands for a treatment with additives. Considering soil conditioning with foam, so far, approaches exist for the investigation of the foam quality and of the conditioning behavior of soils (e.g. (EFNARC GUIDELINES 2001 2003)), but not any standards for testing procedures related to soil conditioning. State-of-the-art research on the topic is and was conducted for example in Bochum (Germany) cf. (Budach 2012; Maidl 1995), in Lyon (France) cf. (Quebaud et al. 1998), in Oxford and Cambridge (Great Britain) cf. (Borghi 2006; Peña Duarte 2007), in Delft (Netherlands) cf. (Bezuijen and Schaminée 2001), in Turin (Italy) cf. (Borio 2010; Peila et al. 2013; Vinai 2006), and in Aachen (Germany) cf. (Vennekötter 2012). Additionally, applied science is reported by the tunneling practice and suppliers of conditioning agents. Although the research focus in all these and further studies varied, similar test methods and test series were applied. A standardization of essential properties and testing methods (setup and procedures) however did not take place. The results from laboratory testing can only function as index values for practice because in the studies, production and application of the conditioning agents mainly takes place under atmospheric conditions. Nevertheless, the tests enable basic understanding of feasibility as well as processes and interactions going on during soil conditioning. For recommendations for standardized and reproducible testing see (Budach 2012; Budach and Thewes 2015).The most extensive investigations on the flow behavior of soil-foam mixtures have been performed by using the slump test from concrete engineering, cf. (DIN EN 12350-2 2009-08), which originally is applied on evaluating the workability of fresh concrete. Although this test does not describe the actual flow behavior, it rather represents an index on the workability, very much experience exists with this test method. Besides others, the workability – or flow behavior – of the EPB support medium certainly is a major factor of influence on the properties of the material in the excavation chamber and thus, for effective tunneling with EPB shields, cf. (Galli and Thewes 2014). For a summary of various investigations on the workability of conditioned soils using the slump test and resulting recommended slump ranges see (Budach 2012; Vinai 2006). Thereof, slumps between 10 and 20 cm have been reported as suitable workability for EPB applications. However, there is actually not much known about the real flow behavior of soil-foam mixtures related to rheological properties such as the viscosity (?) or potential yield stresses (t0). These physical values are necessary for a realistic determination of face pressure, for the design of required torques, and for an evaluation of the material flow at different locations in the excavation chamber, in the screw conveyor or on the conveyor belt. To generate a linear pressure distribution at the tunnel face, as it is assumed a priori, a low-viscosity fluid is favorable, whereas in the screw conveyor, a high-viscous fluid is needed for a controlled pressure decrease. On the conveyor belt, yield stress plays an important role preventing deliquescence and spilling from the belt. Attempts in characterizing the actual flowing of soil-foam mixtures have so far only been made by few researchers, the application of rheometry is rare."

Jan 1, 2016

By Frank Haehnig, Kurt Kogler

"With a height of 200 m, a crown width of 626 m and a concrete volume of 1.6 million m³, the Kölnbrein Dam in the upper Malta valley in Carinthia / Austria is the largest concrete dam in Austria. Boasting a storage capacity of 200 million m³ with a received water load of 54 MN, this is one of the strongest arch dams in the world.During its construction from 1974 to 1977, the dam was equipped with a comprehensive monitoring system capable of comparing developing deformations and stresses with the design values.With a planned reservoir level of 1,900 m a.s.l. the dam saw the reservoir level of 1,860 m a.s.l. breached in the year 1978. This led to extremely high seepage losses of up to 200 ltr/sec and a rise in the foundation water pressure up to 100% of the dam’s height. These observations were caused by the development of horizontal cracks in the area of the middle dam blocks, between the lowest inspection walkway and the waterside.As a consequence, power plant operations had to significantly be reduced and a number of additional measures were carried out – though these did not lead to the desired sealings.The developer subsequently decided that the dam should undergo a general rehabilitation from 1998 to 1994 in accordance with a concept developed by Professor Lombardi. This concept involved erecting a 50 m high support structure with a concrete volume of 500,000 m³ on the airside of the dam, along with the addition of neoprene bearings to transfer 1.2 million tons of the horizontal load. These measures were able to reduce the deformations in the dam enough so that mostly load-bearing injections into the cracks in the dam’s concrete could successfully be carried out by way of targeted grouting measures using injection resin (RODUR) specifically developed for this purpose.In the years 1998 - 1994, a total of 130,000 m of grouting, monitoring and control drillings were executed, and around 200,000 kg of synthetic resin was injected into the cracks in the dam’s concrete.These measures have ensured the dam‘s uninterrupted operation since 1994. A number of small re- injections were again carried out on the contact surface in the years 2011 and 2012."

Jan 1, 2016

By Suzanne R. Hess-Brittelle, Sharon L. Schulz, Tyler J. Quick, Amy F. Ebnet

"Abiquiu Dam is a rolled earth fill dam with impermeable core located on the Rio Chama in New Mexico. Abiquiu has had a history of excessive seepage through the fractured sandstone abutments since water was first impounded in 1963. The foundation was treated with a single row grout curtain in the cutoff trench prior to placement of the embankment. During the 1960’s and 1970’s, the grout curtain was extended 1,000 ft. into both abutments and sections of the foundation beneath the embankment were regrouted. Grouting of the foundation beneath the embankment required drilling through the embankment. Drilling fluid loss or loss of circulation within the impervious core was observed during multiple phases of supplementary grouting and during verification drilling following the 1970’s grouting program. It is likely that the drilling methods employed for these grouting and drilling programs caused hydraulic fracturing of the impervious core. The fluid losses in the embankment may be related to seasonal shutdown layers in the embankment or benches in the abutment foundations. In addition, it is likely that the impervious core was fractured from grout pressures during installation of grout pipe through the embankment.INTRODUCTIONAbiquiu Dam is located on the Rio Chama in New Mexico and consists of a rolled earth fill dam with impermeable core, controlled outlet works, and an uncontrolled rock-cut spillway. The dam was authorized for flood control and sediment retention and was designed as a dry dam, holding flood pools for relatively short durations. The foundation is comprised of Permian and Triassic age, interbedded mudstones and sandstones that were deposited in an active braided stream system. Sandstones are moderately fractured and have variable aperture and infilling. Generally speaking, joints are near vertical. Abiquiu has had a history of excessive seepage through the fractured sandstone abutments since water was first impounded in 1963. The foundation was treated with a single row grout curtain in the cutoff trench prior to placement of the embankment. In 1966-1968, the grout curtain was extended 500-ft into the left abutment and the foundation beneath a 560 ft. section of the embankment was re-grouted. In 1978-1980, the grout curtain was extended 1,000 ft. into the right abutment, an additional 500 ft into the left abutment and the foundation beneath the right 520-ft section of the embankment was re-grouted. The alignments of these grout programs are shown in Figure 1. Grouting of the foundation beneath the embankment required drilling through the embankment. Drilling fluid loss or loss of circulation within the impervious core was observed during both phases of supplementary grouting and during verification drilling following the 1978-80 grouting program. It is likely that the drilling methods employed for these grouting and drilling programs caused hydraulic fracturing of the impervious core. In addition, it is likely that the impervious core was fractured from grout pressures during installation of grout pipe through the embankment. This paper provides a summary of the drilling and grouting methods used during these programs and the potential for damage to the embankment."

Jan 1, 2016

By Michael Gebman, Jack Gerwick

"With the opening of the new San Francisco-Oakland Bay Bridge East Span, the former bridge and its caisson foundations are being demolished. Caisson foundations are in the path of a future shipping channel and therefore need removal down to the mudline 50 ft below water (MLLW). For the first caisson to be removed (E3) a mechanical demolition was performed above the waterline and an implosion was done for the remaining caisson down to mudline. Mechanical demolition consisted of excavators operating from either on top of the caisson, from work platforms or from barges. The demolition was implemented on a trial basis with a successful implosion on November 14, 2015. The work was conducted in an environmentally sensitive area, with measures taken to protect fish, marine mammals and birds. This demolition technique was cost effective, faster to execute, and had a better environmental impact then an alternative option. The demolition, measures implemented to protect the environment, outcome, and lessons learned are presented.INTRODUCTIONThe California Department of Transportation needed a cost effective and environmentally friendly solution for removal of the remaining San Francisco-Oakland Bay Bridge (former East Span) caisson foundations, starting with caisson E3. This was necessary to clear a future shipping channel. One option was to construct a steel cofferdam around the caisson to allow demolition in the dry down to the mudline. This option would take years to complete, be cost prohibitive, and its noise would disrupt aquatic life and birds throughout the cofferdam construction and demolition. An alternative option was implemented on a trial basis to conduct a mechanical demolition of the caisson above waterline along with an implosion of the remaining caisson down to mudline. This had the clear advantage as a cofferdam was not needed, and the demolition project duration would be approximately 6 months, instead of several years for the cofferdam option. The potential impact on aquatic life and birds from the implosion was a concern, as the location is environmentally sensitive; however, measures were implemented to minimize these impacts. As presented in this paper, this demolition option was implemented on a trial basis for Caisson E3. The technique succeeded and will now be used on the remaining caissons.BACKGROUND INFO ON CAISSON E3The reinforced concrete Caisson E3 is the largest caisson which supported the former East Span of the Bay Bridge. It was constructed in 1934, with the Bay Bridge opening in 1936. Figure 1 shows the project location. The caisson had a cell arrangement of 7 x 2 above the mudline. Below mudline, the caisson had a cell arrangement of 9 x 4. A structural transition was made between the 7 x 2 and 9 x 4 cell arrangements with buttress walls. All cells were flooded, as underwater openings were included in the original caisson walls to equalize the hydrostatic pressure. Figure 2 shows the caisson layout with limits for mechanical demolition and for the implosion."

Jan 1, 2016

By M. D. Riegel, P. B. Pizzimenti, E. M. Zamiskie, Britain A. Materek

"The Skanska/Kiewit/ECCO III team (SKE) in association with HNTB was awarded the design-build contract for Phase I of the Kosciuszko Bridge Replacement Project. As lead designer for the SKE team, HNTB was responsible for the design of the Brooklyn Connector which includes construction of approximately 2000 feet of new staged earth-filled embankments utilizing prefabricated modular retaining walls (T-Walls®). The proposed embankments will be constructed adjacent to and beneath the existing Brooklyn Queens Expressway (BQE) viaduct while the existing viaduct remains in service. Critical aspects of the settlement assessment relating to the soils supporting the existing BQE will be addressed, as their behavior drives the deformation of the viaduct. Furthermore, a construction monitoring program was used to enable the designer to assess settlement predictions and allow SKE to mitigate potential impacts to the existing BQE during construction. Additionally, the methodology for installation of the embankments in a limited access area underneath an active viaduct supported on settlement sensitive shallow foundations will be presented.INTRODUCTIONSkanska-Kiewit-ECCO III Joint Venture, in association with HNTB was contracted by the New York State Department of Transportation (NYSDOT) to design and construct the Phase 1 replacement of the Kosciuszko Bridge Design-Build Project. Phase 1 of the project involves the design and construction of the new eastbound structures of Interstate 278 over Newtown Creek from Brooklyn to Queens. The project runs between Morgan Avenue in Brooklyn and the Long Island Expressway Interchange in Queens (approx. 1.1 miles) and includes the staged demolition of the existing structures."

Jan 1, 2016

By Ian Vaz, Takefumi Takuma, Rafael Holcombe, Chris DellAringa

"This paper will discuss the successful installation of seawalls for the first phase of a project in Long Beach in California known as the Naples Island Permanent Seawall Repair – Phase 1. How an unconventional method of pile driving resulted in the reduction of the duration of the project while using less space and maintaining minimal noise impacts to accommodate neighbors will also be discussed. Included in the paper will be how non-vibratory equipment used on this project also significantly minimized the risk of disturbances as well as settlement on residential properties; which in turn greatly reduced the risk of damage to existing structures. The first phase of a 6-phase project along a section of the canals with tight clearances and proximity to residents included the installation of a 1,912 linear-foot steel sheet pile wall system in front of the existing deteriorating walls from January until March 2015.INTRODUCTIONThis project was located in the Naples Island neighborhood of Long Beach in southern Los Angeles County, California. After 80 years of the same seawall structures lining the canals of this beautiful neighborhood, the City of Long Beach Department of Public Works decided that it was time to better protect the area’s multi-million dollar homes by repairing its crumbling seawalls. The City realized that the walls will only become worse due in part to several concerns, including bending failure for the already deflecting walls. According to the City, certain sections of the walls had a significant risk of global failure if the area experienced a “moderate” near-source earthquake (City of Long Beach, CA, 2014b). Although the seawalls were in need of major repair, this would not be simple. Due to the tight clearances of the seawalls between the homes and canals, installation would be difficult with heavy, conventional construction equipment.Phase 1 of the project involved installing sheet piles on the water side in front of existing and aging vertical concrete seawalls between the Ravenna and Toledo Bridges along the Rivo Alto Canal. See Figure 1 for the General Plan for Phase 1. Financing for this project by the City’s Tidelands Capital Improvement’s Division allowed the construction to begin in a timely manner. However, the challenges for the City included regulatory restraints that further complicated the construction in terms of the duration of the project due in part to numerous regulations from several regulatory agencies."

Jan 1, 2016

By Alexi J. Neill

"This presentation will showcase two challenging projects with deep excavation support systems in the Atlanta area where state-of-the-art instrumentation and monitoring systems were used to manage risk by confirming design performance requirements / calculations during construction. The instrumentation and monitoring system successfully reduced risk by recording real-time data on a project website while simultaneously sending email alarms to key site personnel when data exceeded pre-determined alarm thresholds. The monitoring data revealed unexpected performance at an early enough stage so that contingency plans could be engaged and remedial efforts devised in order to limit the consequences. Finite element analysis was used to model deformations, analyze the unexpected performance, and prepare theremedial design.INTRODUCTIONConstruction in densely populated urban areas is becoming more common in order to keep up with the increasing infrastructure demands of our growing population. America’s big cities continue to outpace the overall nation in population growth. The city of Atlanta, the nation’s ninth largest city based on metropolitan population, is a prime example of this. The population has grown at a rate of 6.6% between 2010 and 2013, nearly triple the overall growth rate of the United States during the same period (SustainAtlanta, 2015).As a result of increasing infrastructure demands in Atlanta, developers are now constructing larger buildings on smaller properties. In addition, developers are attempting to maximize space on their selected properties, often by designing underground parking garages to accommodate as many cars as possible on these compact sites. In some cases the selected sites are adjacent to buildings, utilities, and other existing structures. The risk associated with construction increases during underground work that requires a support of excavation system, particularly on confined sites adjacent to existing structures. There is a risk posed to people, property, and the environment that the project team should monitor when constructing in these conditions."

Jan 1, 2016

By J. Erik Loehr, Andrew Z. Boeckmann

"Poor drainage is a common cause of poor performance of earth retention systems, resulting in burdensome serviceability problems that can progress to outright failure of the retention system if not addressed. A drainage system consisting of filtered conical drains that can be installed through the face of an existing retaining wall and readily maintained was evaluated through tests of physical and numerical models. The physical models were constructed with different backfill materials in a container measuring 8 ft wide by 4 ft tall by 15 ft long. Tests were conducted by saturating the backfill under a constant water elevation atop the model, and then maintaining the water elevation until seepage from the drains reached a steady state condition. Pore pressures within the backfill and outflow from the drains were measured to facilitate calibration of numerical models that accompany the physical models. Results from the calibrated finite element models were used to develop design criteria for the drains. The design criteria establish the required drain spacing as a function of the height of groundwater above the drains and the diameter of the drain.INTRODUCTIONMany retaining wall performance problems are a result of poor drainage of the wall backfill. Consequences of poorly drained backfill include displacement and rotation of the wall face, including the extreme case of collapse, and seepage through the face of the wall, which is in turn associated with damage from corrosion, dry rot, and other forms of deterioration. A common approach to improve drainage of an existing wall is the installation of drainage features (e.g. “weep holes”) in the face of the retaining wall. Weep holes facilitate controlled seepage through the face, which relieves water pressure within the backfill and directs seepage to known locations in the wall face. Although installation of weep holes is relatively common, engineering methodologies for selecting the size (diameter) and spacing (along the wall) of facial drainage features are uncommon if not altogether non-existent. This paper documents tests of physical and numerical models of retaining walls with facial drainage features, including conventional weep holes as well as maintainable drains installed through the face and extending into the wall backfill. Results of the testing were used to develop generic design criteria, which establish the required drain spacing as a function of the height of groundwater above the drains and the diameter of the drain."

Jan 1, 2016

By V. A. Sernov

"One of the ways to increase the bearing capacity of a piled foundation is to take into account soil resistance in the base of the raft. Piled raft is similar to shallow foundation and can transfer significant part of the load into the base. It allows reducing number of piles in the foundation or shortening their length. As a result building terms and foundation costs reduce considerably. However, nowadays in Belarus there is no reliable and suitable in design practice methods of calculation of piled-raft foundations. In order to devise such methods we have analyzed the results of piled foundation tests fulfilled by various authors up to date and have carried out series of field and laboratory investigations in Minsk. The most important results of the investigations are provided in the article. Methods of analysis of piled-raft foundations are described.INTRODUCTIONPile foundations of late years are used extensively in connection with the increased number of storeys and load increment on the soil. Often pile foundations are applied in comparative favorable ground conditions at the surface of the base. In such cases the increase of the bearing capacity of foundations and the reduction of construction cost are questions of primary importance for designers. One of the ways to increase the bearing capacity of a piled foundation is to take into account soil resistance in the base of the raft. Piled raft is similar to shallow foundation and can transfer significant part of the load into the base. It allows reducing number of piles in the foundation or shortening their length. As a result, building terms and foundation costs are reduced considerably. However, nowadays there is no reliable and suitable in design practice methods of calculation pile foundations with bearing rafts. In order to devise such methods we have analyzed the results of piled foundation tests fulfilled by various authors up to date and have carried out series of laboratory and field investigations.Long before the constitution of the first piled-raft foundations in the Soviet Union there were attempts to consider soil resistance in the basis of isolated and strip grillages. Such bases can be considered as separate fragments of the piled-raft foundation. Prof. A. A. Bartolomey had tested more than 70 pile foundations of natural size in different ground conditions. The length of piles was 3 12 m (?????????? 1995). The observed results show that the raft carries about 10 12% of the total load applied when length of piles is over 9 m and space between piles is a=3d. Bearing capacity of the raft is about 35 40% when the length of piles is 5 8 m and a=6d. Prof. Golubkov has tested 2 prismatic piles (cross section: 350x350 mm, L=3800 m) and 2 pyramidal piles (cross section: head - 600x600 mm, foot – 100x100 mm, L=3000 m). One of the piles was tested with a raft and the other one without a raft. Significant influence of the raft on total bearing capacity was determined, the more the settlement was the more it influenced on the raft. Bearing capacity of the raft was 27,5% in foundation with prismatic pile and 42% with pyramidal pile (???????? et al. 1971)."

Jan 1, 2016