Search Documents

By D J. Brake

There are many sources of gas in underground mines including development and production blasting, strata gases, spontaneous combustion, diesel equipment, chemicals used for a wide range of functions, welding activities and fires.It is only in relatively recent times that electronic gas monitors (or detectors) have become both safe and affordable for routine use.In modern mines, gas monitors should be in daily use by the ventilation department as well as blasting re-entry (or clearance) crews, and are often used by drilling crews, shift supervisors, hygienists and mine rescue or fire fighting crews.When first released, electronic gas monitors needed to be sent off-site periodically for calibration at a suitable accredited laboratory. Between calibrations, their accuracy was unknown. More recently, ‘bump testing’ and field calibration has become possible on the mine site, improving both reliability and safety as well as reducing the total number of gas monitors that need to be in use.There has been almost an overwhelming increase in the number and sophistication of gas monitor features in recent years. This paper reports on a case study into the key criteria that ventilation practitioners should be aware of with respect to the specification and selection of the most recent gas monitoring systems, and recommends good practice for site-based operation and calibration.CITATION:Brake, D J, 2015. Specification and selection of hand-held gas monitors (detectors) for underground mines, in Proceedings The Australian Mine Ventilation Conference, pp 143–154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By J Jeffery, P G. Knott, F Velge, C Evans

A trigger action response plan (TARP) provides a structured response to escalating levels of risk. In mining, TARPs are typically applied to primary hazards such as inrush, strata failure or heating. Necessary for the creation and deployment of a TARP is a monitoring system capable of detecting deviations from normal conditions. The advent of real-time instruments capable of measuring diesel particulate matter now permit decision-making within shifts to address possible overexposure. Deploying a TARP for diesel exhaust emissions can lower the probability of a person’s average exposure (over a full shift) exceeding the exposure standard by detecting deviations of diesel particulate concentrations from normal conditions. This enables pre-emptive action to mitigate or protect. Another goal is to drive ambient air concentrations lower through the application of corrective actions as a result of instances where concentrations exceed ‘normal’.CITATION:Knott, P G, Evans, C, Velge, F and Jeffery, J, 2015. Trigger action response plans for diesel exhaust exposures, in Proceedings The Australian Mine Ventilation Conference, pp 129–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By A Golsby

Gunite was invented in 1907 by Carl Akeley to repair a crumbling facade of the Field Columbian Museum in Chicago. The method used was to blow dry material out of a hose with compressed air and inject water at the nozzle as it was released. In 1911, he was granted a patent for his invention, the ‘cement gun’; the equipment used; and ‘gunite’, the material that was produced.The advantages of using the dry mix process is that the water content can be adjusted instantaneously, allowing more effective placement in overhead and vertical applications without using accelerators. The dry mix process is useful in repair applications when it is necessary to stop frequently as the dry material is easily discharged from the hose.This paper describes the applications and principles of the gunite pump system in underground coal mining and discusses why it is the preferred spraying system for both cement and plaster products.It also addresses improving productivity and examines dust, respirable crystalline silica (RCS) and health issues around gunite pump systems. The solutions include development of the latest componentry for current gunite pumps to improve their efficiency and allow their operation to be dustless.In particular, this paper addresses:why and where RCS is a problem in underground coal mininghow RCS hazards and its propagation can be managedhow the gunite pump system has become dustlesshow the gunite system has become more productivegunite occupational health and safety issues and how they have been solveda case study of gunite dry spraying.CITATION:Golsby, A, 2015. The development of a dustless dry gunite pump system in underground coal mining – a case study, in Proceedings The Australian Mine Ventilation Conference, pp 41–48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By D Cliff, B Belle

Trigger action response plans (TARPs) are inherent to managing multiple hazards such as high gas content with multiple coal seams, high spontaneous combustion propensity, heat and ventilation. TARPs aim to provide assurance and guidance when the situation deviates from the original plan or there is a change in conditions that could be hazardous. Over the years, learnings from various incidents have continuously required coal operations to revisit the TARP trigger values that were based on historical data or guidance values from the industry. In most cases, the background to the basis of TARP statistical data (ie average, maximum, hourly or daily for the monitoring or sampling location) is unknown. The introduction of real-time monitoring devices to monitor gases and airflows has provided greater understanding of the hazard scenarios and their controls. This paper analyses the carbon monoxide data from operating longwall mines and compares these with the historical trigger values to understand the changes and identify improvement opportunities while setting trigger levels in the TARPs. As an example of setting trigger values, those used during the sealing of a panel are explored in terms of setting values based upon the sampling location and the level of risk. It is envisaged that the learnings shared herein will further enhance the understanding and management of multiple hazards in Australian coalmines.CITATION:Belle, B and Cliff, D, 2015. Improved trigger action response plan development based upon mine-specific data, in Proceedings The Australian Mine Ventilation Conference, pp 73–78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By B Wu, B W. Lei, B J. Duan

When a coalmine fire occurs, it is crucial to judge the developing trends inside the fire area by analysing the changes of gas concentration in order to formulate the proper rescue measures. At present, few researchers have focused on the relationship between the changing trend of gas product and basic characteristics of fire in the coal fire extinguishing process. To study the relationship of basic characteristics of coalmine fire during the extinguishing process, an experimental platform for coal combustion in a confined space was built, and gas production, flame image and coal temperature during the extinguishing process were monitored and analysed by an online continuous gas analysis instrument, camera and thermocouple. Research shows that during the burning phase of the coal sample in the confined space, the flame zone decreases gradually due to insufficient gas supply. The size of the flame zone fluctuates and shares a positive correlation with CO concentration, while sharing a negative correlation with O2 and CO2 concentrations. Then, in the extinguishing phase, the increasing rate of CO2 concentration and the decreasing rate of O2 concentration both decrease gradually, but CO concentration would rise for a period before it eventually decreases. Coal temperature continues to rise in the open flame stage and does not go down until the flame is extinguished.CITATION:Lei, B W, Wu, B and Duan, B J, 2015. Experimental study on extinguishing characteristics of coal fire in confined space, in Proceedings The Australian Mine Ventilation Conference, pp 279–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By F Hungerford, T Ren

"Gas management has always been a major concern for the ventilation officer of any gassy mine. With an increase of mining depth and gas content, there is a great demand for the development of in-seam drilling sites where boreholes can be drilled for the pre-drainage of gas prior to longwall operation. The ventilation and gas management in the drilling site therefore becomes a critical component of mine safety. In this study, advanced computational fluid dynamics technology was adopted to investigate the aerodynamics of gas emitting from the drilling site and boreholes during normal drilling and, in the case of a sudden gas inrush, from the borehole. In addition, the impact of different ventilation controls on gas removal in the drilling site was investigated. Modelling results indicate that gas accumulation zones could be formed if the ventilation system fails to deliver sufficient airflow to the drill site, especially when a sudden gas inrush from a borehole occurs. The configurations of brattice, layout of ventilation tubes and the gas emission rate all have a significant effect on the gas distribution. Due to variations in site-specific conditions, it would be desirable to conduct modelling studies to assess the effects and efficiencies of a ventilation design for the varying environment on-site before carrying out drilling practice. CITATION: Ren, T, Hungerford, F and Wang, Z, 2015. Computational modelling studies of ventilation management for underground in-seam drilling sites, in Proceedings The Australian Mine Ventilation Conference, pp 239–250 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 31, 2015

By H W. Wu

Occupational exposure limits for diesel particular matter (DPM) are progressively being adopted in a number of countries. Many of these follow the lead of the US Mine Safety and Health Administration initiated in 2008. In line with adoption of best practice it is accepted that all exposures should be reduced to as low as reasonably achievable. The management of diesel emissions and occupational exposures to those emissions requires an integrated strategy incorporating efforts from all key departments on a mine, including management, production, maintenance, supply and occupational health and safety.Australian coalmine longwall moves rely on the use of high-powered diesel equipment such as chariots and other machines that produce exhaust pollutants of gases and DPM. To reduce mine personnel’s exposure levels to DPM a hierarchy of controls can be followed. Minimising the use of diesel equipment, better operator positioning in relation to exposure source, using efficient engineering methods and adopting better ventilation to reduce concentrations through dilution are some of the controls that can eliminate exposures. Approaches generally adopted in Australian longwall mines currently rely on a combination of strategies such as optimisation of ventilation, use of diesel particulate filters and use of diesel tag boards that minimise the number of vehicles through recording entry and exit into working panels.A study has been undertaken into the mine ventilation systems currently in use during longwall moves within Australian modern longwall extraction mines. This paper reviews current longwall section ventilation systems and discusses evolving changes being adopted to address the more complex problems in dealing with section DPM during phases of the operational moves. The effects of DPM on crew members as well as the diesel equipment operators within a longwall section are examined. Issues that should be considered in designing the longwall section ventilation during the moves are discussed.CITATION:Wu, H W and Gillies, A D S, 2015. Review of ventilation optimisation strategies during longwall moves, in Proceedings The Australian Mine Ventilation Conference, pp 133–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By A S. Derrington

High-accuracy, solid-state digital reference barometers have proven to be well suited to conducting underground barometric pressure surveys. The only problem is their expense; at least A$4000 each. For this reason, and because barometric pressure surveys are not a routine undertaking, very few mines have been able to justify the purchase of suitable instruments. The author knows of only three Australian metalliferous mines that own them.However, this may soon change given the recent development of low-cost, mass-produced miniature barometric pressure transducers. These transducers were developed to provide an altimeter function in the latest generation of smartphones. The main purpose of the inbuilt altimeter function is to allow the smartphone to be aware of its altitude when the global positioning system satellite signal is lost.This paper describes a prototype barometer that was constructed using one of the most accurate of the latest generation of piezo-resistive smartphone barometric pressure transducers. The prototype instrument was constructed for less than five per cent of the cost of a commercially available digital reference barometer. The prototype was subsequently tested against a reference barometer at the University of Queensland’s Experimental Mine to verify its accuracy and suitability for measuring pressure differences between underground survey stations.It is expected that the instrument’s low cost will pave the way for barometric pressure surveys to become more commonly used in mines. In turn, the resulting improvement in knowledge of major underground pressure losses should allow mine ventilation officers and engineers to optimise their ventilation systems and potentially reduce overall operating costs.An alternative option would be to use a barometer-equipped smartphone as a survey instrument, provided that its inbuilt barometer module is sufficiently accurate.CITATION:Derrington, A S, 2015. Development of a low-cost instrument for barometric pressure surveys, in Proceedings The Australian Mine Ventilation Conference, pp 331–336 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By G Collecutt, D Proud, D Humphreys

"The hazards associated with dust explosions are well known, and coal dust explosions present a significant hazard in the underground coal mining industry worldwide. In earlier work, we presented computational fluid dynamics (CFD) simulations and test results for coal dust explosions within a 2.5 m diameter circular gallery, along with CFD simulations and test results for the suppression of these explosions with finely atomised water sprays. In this paper, we present refinements to the CFD modelling that yield a significantly improved calibration with the test results, and proceed to investigate by CFD the requirements for suppression of a coal dust explosion in a typical underground roadway. This work was carried out under an ACARP project and we gratefully acknowledge their assistance. CITATION: Proud, D, Collecutt, G and Humphreys, D, 2015. Computational fluid dynamics modelling of coal dust explosions and suppression systems, in Proceedings The Australian Mine Ventilation Conference, pp 309–314 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 31, 2015

By J J. L du Plessis, A Spaeth

The objective of this paper is to demonstrate the efficiency of machine-mounted active explosion suppression systems (AESS). Their proven effectiveness against methane explosions is highlighted, as well as their additional potential when used as an early warning system should frictional sparks occur during the coal-cutting operation at the coalface.Methane and coal dust explosions remain one of the primary and unpredictable risks in underground coal mining. Although technologies such as proactive ventilation, methane monitoring and wet-head cutting systems are widely used as preventative measures, there are no fail-safe controls able to reduce the risk to zero. None of these controls is designed to be able to counter the negligence associated with human error or to deal with rapidly changing face conditions which could lead to flammable gas ignitions. Machine-mounted AESS have been installed on various continuous miners as an additional control to further reduce the risk of ignitions and to act as a safety shield when all the other precautions taken have failed. This was the primary motive for the development of AESS. As an additional feature, the ExploSpot® AESS is being enhanced to identify frictional ignition sources at the coalface that reach a predefined monitoring level. This functionality may serve as a further effective preventative measure.As part of ensuring coalmine operational safety, the detection of frictional ignitions can play a huge role in creating heightened awareness of potentially dangerous situations. By being able to process the frictional spark burning pattern, the AESS could support the decision-making process regarding whether to continue the coal-cutting operation, whether there is a need for maintenance or whether the operation should be stopped completely due to the increased risk of a flammable gas ignition and an ensuing explosion.CITATION:Spaeth, A and du Plessis, J J L, 2015. Enhanced risk reduction using early warning technologies embedded in active explosion suppression systems, in Proceedings The Australian Mine Ventilation Conference, pp 315–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By B T. Qin, C Zhu, Y W. Jia, Y Lu, F L. Li, Q L. Shi

Air leakage through rock fractures in coal mining is a major cause of coal spontaneous combustion. In order to overcome the deficiency of the existing fire control technology and prevent coal spontaneous combustion by isolating coal from oxygen, the article proposes a novel technology of inorganic solidified foam (ISF) with high expansion to fill fractures effectively. ISF consists of fly ash, cement, setting accelerator, redispersible polymer powder, water and aqueous foam. For preparing homogeneous and stable ISF, a preparation system with a pore type foam generator, a mixer device installed with a hollow shaft and helical blades, air compressor, slush pump and monitoring instruments was developed, and the working principles of key devices were elucidated. Based on a series of experiments on the different ratios of each component material and technological parameters of the preparation system, ISF with a foam expansion ratio of 8~10 and dry density of 250–400 kg/m3 was prepared. The relationship between elastic compressive strength, modulus of elasticity and density was summarised. Based on the injection experiment for fracture of loose coal pile with high temperature, the characteristics of sealing air leakage, compressive strength, thermal insulation, flow and cooling of ISF in the fresh state were investigated, indicating that ISF can effectively cut off the air leakage and cover the coal sample to reduce the temperature in the earlier stage, and ISF can remain stable and not crack. The ISF was applied to Luwa coalmine to seal small coal pillar pressure fractures and loose coal fractures in goaf. After press-casting the ISF in Luwa coalmine, the pressure-difference of inner-outer increased, meaning the effect of external conditions on the pressure-difference decreased, showing that it could plug the air leakage effectively.CITATION:Qin, B T, Shi, Q L, Lu, Y, Zhu, C, Li, F L and Jia, Y W, 2015. The novel technology of inorganic solidified foam with high expansion for preventing coal spontaneous combustion, in Proceedings The Australian Mine Ventilation Conference, pp 121–126 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By B Shi, Y Li, L Ma, F Zhou

Subsurface fires are a common threat to coal mining, as spontaneous combustion of coal can potentially result in gas combustion and explosion. Fire-proof techniques, such as grouting, foam, or colloid injection, are not in a position to function ideally, due to the limited coverage and stopping the extinguishment substance from reaching the fire location. Liquid nitrogen, as a kind of all-submerged fire prevention or extinguishing method, can rapidly extinguish fires, thus preventing gas explosion and minimising extinguishment time. Injecting liquid nitrogen through boreholes is an important way during the period of mine catastrophe. But liquid nitrogen is not effective enough in infusion; technical issues restrict the development and utilisation of liquid nitrogen fire prevention and extinguishing technology. Immediate infusion of liquid nitrogen is usually associated with ‘air slug’ (the balloons and bubbles in the pipeline which hinder the flow of low-temperature liquid), which blocks pipelines for liquid nitrogen injecting. Another issue is that the pipeline tends to be damaged due to freezing, which undermines the injecting efficiency of liquid nitrogen and its application result. In order to solve the problems of the low efficiency and some other related field issues in liquid nitrogen perfusion, the ground–underground high efficiency liquid nitrogen injection technology were developed. Implementation of liquid nitrogen infusion techniques in Chinese coalmines achieved the goals of fire prevention and air-cooling. The technique presented in this paper is efficient in absorbing heat, and consequently, displacing oxygen and combustible gases. Field tests at Rujigou and Yangchangwan Coalmine justified the efficiency of the technique. By using this technique, there was no waste left behind, which may impede the subsequent production. The presented technique is of great benefit to the social, economic, and environmental aspects of mining operations, and will have broad applications in fire prevention for large-scale coalmines.CITATION:Zhou, F, Shi, B, Li, Y and Ma, L, 2015. Key techniques and engineering applications of stereoscopic liquid nitrogen infusion for coalmine fire prevention, in Proceedings The Australian Mine Ventilation Conference, pp 291–298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By S Bluhm, L van den Berg

In planning mine ventilation systems, heat issues are normally associated with deep-level mines where auto-compression and virgin rock temperatures play a major role. However, a number of mines suffer from high ambient temperatures and humidity, very steep virgin rock temperature gradients and an influx of hot groundwater. Mines in Australia and, particularly, South-East Asia have to deal with these environmental conditions, both in the operational and planning phases. These operations normally have to take heat into consideration during the planning stages at much shallower depths. In high rainfall regions, the water table is saturated and groundwater flow rates are particularly high, which add significant water heat load potential to the mine ventilation system.This paper considers the ventilation challenges associated with hot groundwater conditions in mechanised mines. The paper is based on specific project experience gained from a number of projects in the United States, Australia and South-East Asia and draws on data from mines that experience hot groundwater conditions. For one site, actual decline temperature survey measurements, modelling techniques, management strategies and design considerations are presented.CITATION:Van den Berg, L and Bluhm, S, 2015. Ventilation planning considerations when dealing with hot groundwater, in Proceedings The Australian Mine Ventilation Conference, pp 211–218 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By O Jones

Longstanding occupational health challenges of the underground hard-rock mining sector require both an analysis of historical data to assess evidence of linkages between the source of the problem and subsequent illnesses, as well as investigating the means by which health risks to workers can be eliminated or minimised. This paper refers briefly to a recently established National Health and Medical Research Council (NHMRC) sponsored Epidemiological Study into the incidence of Lung Cancer, contracted by mineworkers in Western Australia (WA) due to the inhalation of diesel exhaust fumes from 1996 to 2012. Thereafter it reviews current knowledge of the nature of the challenges facing those responsible for the health and wellbeing of underground hard-rock miners in WA, commencing with the recent categorisation of diesel exhaust as ‘Carcinogenic to Humans, Group 1’, by the World Health Organisation’s (WHO) International Agency for Research on Cancer (IARC). An attempt is also made to explore how the challenge has changed with the adoption of more advanced engine technologies, including the increased generation of ultra-fine volatile organic and other nucleates, submicron carbonaceous agglomerates and toxic gases.The compounding effect of using the mine decline access entry as both the primary ventilation intake and haulage-way is also discussed, as is the need to develop a more appropriate metric for regulating diesel engine emissions. Finally the paper refers to ongoing in-mine research pursued by the National Institute for Occupational Safety and Health (NIOSH) at its Diesel Laboratory in an underground limestone mine near Morgantown in the USA.CITATION:Jones, O, 2015. Diesel exhaust and the underground miner in Western Australia, in Proceedings The Australian Mine Ventilation Conference, pp 167–172 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By R W. Wilson, A R. Branch, T S. Pooe

The original bulk air cooling system at this particular mine made use of two water chilling refrigeration machines to produce peak cooling of approximately 12 MWR with a downcast air temperature of about 7°C; however, as the shaft is not used for transporting personnel, the opportunity existed to supply more cooling to the mine by lowering the downcast air temperature. An ice storage facility has been constructed and provides a range of opportunities in operating the system: colder air temperature sent to the shaft, enabled by using near-zero degree water produced by melting ice to cool the air; electricity time-of-use management, by shifting electricity usage out of peak tariff periods; and increased peak cooling capacity, by melting ice while chilling water. Ice is created in the storage facility at night while the ambient air temperature is low and then melted to produce cold water when required by the cooling process. An ice dam was constructed and serpentine stainless steel coils installed where the ice is produced; one of the refrigeration machines was converted to chill a glycol solution to subzero temperatures to create the ice on the coils; a plate heat exchanger was installed to allow the glycol chiller to act as a water chiller as well; and a third spray stage was added to the bulk air cooler to utilise the near-zero water. This paper describes the thermodynamic design, construction and performance assessment of the new system, which is unique, novel and represents the state-of-the-art of this type of cooling system and energy management.CITATION:Branch, A R, Wilson, R W and Pooe, T S, 2015. Novel use of ice thermal storage for energy management on a mine refrigeration plant, in Proceedings The Australian Mine Ventilation Conference, pp 185–192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By A J. Clough

There has been an unprecedented rise in the fatality rate in the Australian mining industry over the last few years. The factors behind this rise are not clear; however, it is noted that the increase in fatalities has occurred during a fall in commodity prices.This paper examines prevention methods and systems to deal with hazards that have the potential to result in either single or multiple fatalities. Managing the risks associated with mine ventilation is used to illustrate the principals behind the approach.The paper also touches on the broad science of human error and proposes a multifaceted approach to controlling and preventing fatal risks.A summary of the steps involved in developing an effective principal hazard management plan is provided.CITATION:Clough, A J, 2015. Ensuring an effective principal hazard management plan, in Proceedings The Australian Mine Ventilation Conference, pp 3–8 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By A Golsby

Both primary and secondary ventilation is important in underground mining. Secondary ventilation refers to the provision of ventilation to development ends, stopes and services facilities, which constitute secondary circuits tapped off the primary circuit or main through flow of air.An unbalanced primary and secondary combination can cause re-circulation, which is inefficient and potentially hazardous. These inefficiencies extend into operational and other considerations, such as power.Most cost justification analysis covers capital and physical consumables. These analyses are often not comprehensive or holistic. This case study is an example of ‘how to holistically justify’ a secondary ventilation circuit and optimise it to meet all stakeholder needs.This paper particularly addresses the following:how to account for all stakeholders in a secondary ventilation cost justificationthe secondary ventilation componentsthe cost justification outcomes and how to measure themsome of the sensitivitiesthe stakeholdershow to present the justification to meet the stakeholder needssecondary ventilation cost justification.CITATION:Golsby, A, 2015. Secondary ventilation as a value proposition – a case study, in Proceedings The Australian Mine Ventilation Conference, pp 49–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By M Watkinson

Tube bundle monitoring systems have come a long way from their first introduction to coal mining in the late 1960s/1970s. Early developments in the United Kingdom (UK) commenced with single gas analysers (carbon monoxide) and quickly moved towards introducing oxygen analysers and methane analysers for improved analysis, in particular the calculation of air-free results. Recommendations were made in the early days as to how and where to run tubes and on the matching of sample pump and purge pump pressures. Current Australian installations are commonly based on a four-gas multianalyser, infrared for carbon monoxide, carbon dioxide and methane, and paramagnetic for oxygen. These systems are controlled with programmable logic controllers (PLC), with component monitoring as an integral part of the software. This paper discusses the development of tube bundle systems from the 1960s to the current date and looks at the advantages and disadvantages of the installations, along with making operational recommendations to be considered with the siting of the analyser building, running of tubes and maintenance of the system.CITATION:Watkinson, M, 2015. Developments in tube bundle gas monitoring, in Proceedings The Australian Mine Ventilation Conference, pp 259–266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By H R. Phillips

During the 1980s and early 1990s, the South African coal industry experienced a series of methane explosions in which well over 200 coal miners lost their lives. In addition, a fire and an explosion in the gold mining sector claimed a further 240 lives. These tragic incidents resulted in the establishment of a research facility at Kloppersbos dedicated to explosion and fires research and the funding of an extensive research program, and almost certainly influenced the government of the day in its decision to establish, in 1993, the Leon Commission of Enquiry into Mine Health and Safety. The results of this focused research program, the wide-ranging recommendations of the Leon Commission and the determination of the coal mining industry to improve its safety record all combined to result in the past 20 years without a major explosion.This paper lists some of the research outcomes and, through three case studies, illustrates what can be learnt from investigations following explosions. The paper concludes with an evaluation of some of the findings of the Royal Commission on the Pike River coal tragedy. Many of the Commission’s conclusions are pertinent and relevant to the coal mining industry worldwide and their implementation could significantly improve coalmine safety; however, a careful study of the available facts indicates there could well be an alternative explanation of the source of the methane, the location of the ignition and the size of the explosion at the Pike River coalmine.CITATION:Phillips, H R, 2015. Lessons learnt from mine explosions, in Proceedings The Australian Mine Ventilation Conference, pp 19–28 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By T J. M Harvey

This paper gives an overview of the ASHRAE LibHuAirProp, CoolProp and REFPROP software packages. These packages were predominantly developed for heating, refrigerating and air conditioning engineers and the refrigeration and steam power industries, although CoolProp and REFPROP also cover combustible gases. The main aim of this paper is to highlight the existence capabilities and status of the different packages and where they can be used. The paper gives typical examples of the use of these software packages, specifically as Excel add-ins, and provides a comparison of results of typical mine psychometric and gas drainage calculations using the packages and more traditional ventilation and gas drainage calculation methods. The paper also introduces a hybrid method that improves accuracy compared to traditional methods. In typical mine situations, the use of software packages is probably not required; however, with the increasing accuracy of instruments, potential greenhouse emission costs and the sale of mine gas, more accurate measurements and calculations can potentially save (or make) significant sums of money.CITATION:Harvey, T J M, 2015. The use of psychometric, thermodynamic and transport property software in mine ventilation and gas drainage calculations, in Proceedings The Australian Mine Ventilation Conference, pp 201–210 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015