Search Documents

By Michael V. Wolski, Ryan O. McCarter, Kenneth A. Johnson

"The Central Subway is Phase 2 of the San Francisco Municipal Transportation Agency’s (SFMTA) Third Street Light Rail project and will extend the existing Phase 1 initial operating segment from its current connection to the Embarcadero line at Fourth and King streets along Fourth Street to Market Street, under the Bay Area Rapid Transit (BART) and Muni Metro tunnels and then north beneath Stockton Street to Chinatown (Fig. 1).Total new track to be constructed as part of the Phase 2 work consists of approximately 734 m (2,410 ft) of surface track and 2,636 m (8,650 ft) of tunnels. The tunnels were constructed as twin, singletrack bores by two tunnel boring machines (TBMs) (Johnson, 2014) moving north from the southern end of the launch box under the I 80 freeway between Bryant and Harrison streets. North of Chinatown Station the TBMs continued another approximately 683 m (2,240 ft) to a retrieval shaft near Columbus Ave. at Washington Square. The project also includes five cross passages to connect the two tunnels, and three underground stations (the Yerba Buena/ Moscone Station, Union Square/Market Street Station and Chinatown Station.)Excavation of the twin tunnels was performed with two TBMs, with both TBMs driving northward from the launch box. TBM excavation was performed such that the location of the machines was staggered to separate the active excavation faces by a minimum of 91 m (300 ft) between headings. This minimum separation was maintained until the first TBM arrived at the retrieval shaft plug, at which time the separation requirement was relaxed.Excavation began with the “southbound” (SB) tunnel which will ultimately accommodate the southbound TBM light rail trains followed by the second TBM in the “northbound” (NB) tunnel. With the completion of the drives in June 2014, cross passage excavation then began and was completed in April 2015. Overall, construction of the Central Subway tunnels was a success considering the nature and complexity of the project. Additional details of the completion of the Central Subway tunnels are presented in another paper from the RETC 2015 conference (Leong et al., 2015)."

Jan 1, 2015

By G. Armand, A. Noiret, D. Seyedi, J. Morel

"Clay formations in their natural state exhibit very favorable confining conditions for repository of radioactive waste because they generally have a very low hydraulic conductivity, small molecular diffusion and significant retention capacity for radionuclides. Nevertheless, one concern regarding the hydromechanical behavior around drifts in such claystone is the associated pore pressure field disturbance during excavation works. In the short term, the very low permeability leads to an almost “undrained” condition, meaning that the stress change due to face advance will create volumetric strains leading to an increase or decrease of pore pressure. If the effective stresses reach the failure level, the induced damage around these excavations might change the favorable properties of such formations. To demonstrate the feasibility of a reversible deep geological disposal of high-level and intermediate-level long-lived radioactive waste (HLW, IL-LLW) in the Callovo-Oxfordian claystone (COX) formation, the French national radioactive waste management agency (Andra) started in 2000 to build the Meuse Haute-Marne underground research laboratory (M/HM URL). The present paper illustrates observed pore pressure changes during excavation of drifts (˜5 m diameter), of micro tunnels (˜0.7 m diameter) and a borehole (˜0.15 m diameter). All these openings are parallel to the major horizontal stress at the main level of the M/HM URL. In drifts parallel to the major stress (i.e., when the initial stress field in the drift section is quasi-isotropic) an important increase followed by a drop of pore pressure is observed in the horizontal plane at the drift wall. These observations emphasize the impact of the in situ stress state and rate of excavation on the pore pressure and provide important insight of the hydro mechanical behavior of the COX claystone and the relationship between pore pressure and excavation induced fractures zone."

Jan 1, 2015

By M. Hozayen, Q. Ni, E. S. Radwan, P. Nawrocki, A. Jebbouri

"A major geomechanical study was conducted for one of the UAE onshore oil fields with the purpose of studying reservoir rock properties and stress distribution, based on which a 3D coupled reservoir geomechanical model was built. This model was later used for wellbore stability analysis and for analyzing the effect of fractures on future reservoir production performance, including fracture deformation and permeability evolution occurring due to reservoir depletion and resulting changes in local stress field. The subject of this study was a complex fractured Upper Cretaceous carbonate reservoir characterized by high degree of heterogeneity, both vertically and laterally. Wellbore instability related drilling problems were encountered while drilling the wells in this field. The problems were mainly in drilling the horizontal wells, including breakouts and mud losses. Experimental results of laboratory tests used in this study are summarized in Part I of this paper whereas wellbore stability analysis and formulation of a3D geomechanical model that was built for that purpose is summarized herein.A 3D geomechanical reservoir model was developed, which included natural fractures. The mechanical properties of the reservoir rock, such as Young’s modulus, Poisson’s ratio, UCS, friction angle and tensile strength were populated based on the correlations established in Part I of this paper and the developed model was then used to simulate the 3D mechanical-property distribution and the evolution of the in situ stresses in the field due to depletion from 1983 to present-day. Based on the full field model, mud weight cubes were developed to predict the safe mud weight windows in different drilling directions. In addition, well stability prediction for two planned wells was performed using a 3D near-borehole model. Firstly, the computed stress state and mechanical properties simulated in the full field model were extracted along the well trajectory of an existing horizontal well which was drilled recently and then, a3D near-borehole model was constructed along the well trajectory. The wellbore stability analysis along the well trajectory, including stress state, strain distribution and displacements, was performed to identify the instability events along the well trajectory. It has been seen that the presence of natural fractures is closely related to the recorded borehole instability incidents. The computed plastic strains which indicate the wellbore failure were consistent with the recorded wellbore instability events in the FMI image logs, what provide further verification of the developed model. Then, this 3D near-borehole model was applied to two planned horizontal wells and the wellbore stability analysis for the two wells was carried out.The results showed that drilling vertically in the reservoir is safer than drilling horizontally. However, the drilling mud weight window in the vertical direction is narrow, being as narrow as 18.7 pcf or 0.299 sg locally. Drilling horizontally is less stable towards the maximum far field stress direction than towards the minimum far field stress direction. The mud weight cubes were used to identify the optimal well placement and well trajectory. For planned well trajectories, this technology can also be used to determine the optimal mud weight."

Jan 1, 2015

A reliable laboratory method to characterize the response of free gold particles to flash flotation conditions has been developed. The test has been performed on free milling gold ores as well as synthetic ores, using either a gravity concentrate or gold powder as the gold source, to assess the floatability of gold particles. Trends in free gold flotation kinetics, as well as size and milling effects, were identified for gold recovery based on the different feed types, reagent dosages, and residence times. It was shown that the ultimate recoveries and kinetic trends of gold particles from the gravity concentrate could be enhanced with increased dosage of collector, potassium amyl xanthate. Interestingly, in comparison to gravity-recoverable gold, recovery from pure Au powders was better in collectorless flotation, and cumulative recovery decreased with higher levels of collector addition. Improved coarse particle recovery appeared linked to increased collector additions for both the gravity concentrate and the pure gold powders. In general, coarse gold particles demonstrated slower kinetic rates thaen the fine or intermediate components incomparable tests.

Jan 1, 2015

By George P. Demopoulos, Yan Zeng, Zhibao Li

Precipitated silica is marketed with a rising demand as reinforcing filler in the rubber industry and as a potential raw material for the synthesis of lithium-ion battery electrodes. Due to an awareness of the environmental impact of the existing processes for the production of precipitated silica, a green and sustainable process was proposed by using sodium bicarbonate (NaHCO3) as an alternative to sulfuric or hydrochloric acid in the precipitation reaction with sodium silicates. The use of NaHCO3 allows for better control of the supersaturation and pH to form silica with desired quality. Additionally, Na2CO3 solution as the process by-product is recyclable because it could be recovered to produce NaHCO3 by absorbing CO2. The solubility of sodium metasilicate nonahydrate (Na2SiO3·9H2O) in the Na-CO3-HCO3-OH-H2O system was measured using a dynamic method in the temperature range from 288.15 to 308.15 K. It is found that the solubility of Na2SiO3·9H2O decreases with increasing concentration of either Na2CO3 or NaOH over the investigated concentration range. With the aid of the OLI platform, a chemical model for the Na2SiO3-Na-CO3-HCO3-OH system was established with newly obtained interaction parameters of the Bromley-Zemaitis model by regression of experimental solubility data. The new model predicted the solubility of Na2SiO3·9H2O in multi-component systems with good agreement and was used to conduct a preliminary feasibility study of the new process.

Jan 1, 2015

By J. Hu, F. Lin, R. Chen, F Peng, S. Yang, W. Yu

"Microseismic monitoring technology has become one of the most effective method of mine ground pressure monitoring after decades of development. But safety assessment of mine ground pressure by using microseismic monitoring is still in the development stage, it needs to be perfected continuously in practice, and choose the optimal assessment indexes and methods. The definitions and physical meanings of wave velocity, b value, and EI-VA value are introduced in this paper. Statistical calculation of the microseismic events in Luomu Mine is finished by using these indexes, then the functions and calculation results of V, b value, and EI-VA value with the variable of time are also given in the paper. The preliminary safety assessment method is established in Luomu Mine, and it has achieved good results in practical application.1.1 Engineering background The Luomu Mine is a super large molybdenum and tungsten production base in China, ore reserves is up to 2 billion tons, first in Asia and third in the world. It begins mining since the 1960. and bases on underground mining until 2002. In order to recover resources more effectively, it began to use opencast mining method and formed a production of 30000t/d in the early 1990. After about 30 years of underground mining, a large mined out spaces was formed under open pit mine, up to area of 1.2 million m2 and volume of 18 million m3, as shown in figure 1. The large number of mined out spaces seriously affects the normal production, mining and handling of mined out spaces are in the high risk. In the past years, several rock mass collapsions happened, and it caused a serious security threat to persons and equipments. According to the distribution characteristics of mined out spaces, Luomu Mine is divided into A, B, C, D and E mining area. The stability of D mining area is studied in this article. D mining area mainly includes 1376,1350,1340,1317 mined out spaces and 1280 deep large mined out area, as shown in figure 2. The mined out spaces of D mining area is extremely complex and high-risk. Therefore, a microseismic monitoring system was built to monitor the stability of D mining area, a large number of valuable datum has been obtained, and it has a striking effect (Cheng & Peng, 2013; Peng et al., 2013)."

Jan 1, 2015

By Kaushik Mukherjee

"Malaysian offshore and surrounding region are favorable to the installation of driven piles. During the design phase, pile driveability analysis plays a major role in pile make-up design to suit and selection of the feasible hammer, besides defining acceptance criteria to ensure a certain level of confidence of its fitness for purpose. The accuracy level of driveability analyses depends substantially on the selection of its parameters that best represent the in-situ scenario. The most uncertain of the parameters are those related to the soil model. It is noted in various projects in the region, that the consideration of suitable soil resistance to driving, coupled with soil dynamic parameters, significantly affects driving sequence planning, design, material, hammer selection and most importantly pile acceptance criteria. This is particularly relevant for a region that contains predominantly clayey subsoil resulting in large diameter, long friction piles susceptible to driving disturbances and slow strength recovery. Various researchers suggested suitable dynamic parameters and soil resistance during driving calibrated to specific regions. Regional experience suggests a set of soil degradation and parameters to suit the different stages of driving which is corroborated by pile monitoring records during continuous and delayed driving scenarios. The most sensitive amongst all dynamic soil parameters is the skin damping in clay. Smith’s wave theory approach considers a conservative assumption in selecting the parameters in absence of site-specific data, while a different approach may be adopted based on consistency of the clay for a site where the geotechnical parameters are well defined. This paper summarizes some independent studies on the effects of variations in dynamic parameters and resistance at different stages of driving and suitability of choices of different pile make-up and hammers for an optimum design. Similar experiences, coupled with simulation studies and back-analyses of available driving records suggest a reasonable judgment for the region.INTRODUCTIONFixed structures are generally supported in the in-place condition on a pile foundation those may either be driven or drilled & grouted piles depending on the subsoil. The piles may be driven inside the jacket legs or drilled through individual skirts normally grouped in clusters at the base of each leg. The types of subsoil dealt with in the Peninsular Malaysia and Gulf of Thailand surrounding region are conducive to the installation of driven piles only. The design of an offshore pile is fundamentally the optimization of pile length, size and make-up those are suitable to the requirement and supply. An interactive effort combining aspects related to geotechnical, structural and constructability are required to converge into a feasible, safe and economic solution. Other than the checking of the installation feasibility using a set of hammers in a given environment, driveability analysis is also used to define acceptance criteria for a majority of the offshore piles. Unlike short and end bearing piles in sand/soft rock, the piles in clayey subsoil regime often could not be rested on a dense strata where it could be met by a definite set criteria. Usually a measurement of blow counts determined and defined by driveability analyses forms the acceptance criteria to ensure a certain level of confidence of its fitness for the purpose coupled with an optimum penetration. While softness and uncertainty of the soil strata at target penetration may be resulted in possible overdrive, an unusual delay or the presence of an unidentified cemented layer or a boulder may cause early refusal or underdrive scenario. Hence, accuracy of the investigation, driveabilty study as well as the precautionary measures to avoid delays during driving are of equal importance."

Jan 1, 2015

By Ziyad Abunada, David O’Connor, Fei Jin, Abir Al-Tabbaa

"In-situ remediation of contaminated land with deep mixing can enable a multi-technique remedial strategy on the same site combining low permeability barriers, permeable reactive barriers, stabilisation/ solidification treatments as well as ground improvement, delivering significant advantages over alternative strategies. This was the core objective of Project SMiRT (Soil Mix Remediation Technology) which involved the execution of the largest research field trials in the UK to date to provide field validation for this technique. Around 800m3 of soil were treated on a contaminated site in Yorkshire in May 2011 with 6 different treatments, testing ~40 binder compositions and 10 different installation methodologies. Field monitoring, testing and coring activities at the site took place within the first 2 months after treatment and then again at 34 months after treatment. This paper presents an overview of the field activities to date and some 3-year results and assessment of a subset of the treated soil sections. Some good correlations are seen together with some clear differences between treatments. There is generally an observed consistency with depth, with the mixing effectiveness having a more profound effect than the binder composition or content, within the tested materials and ranges. These field trial activities are currently being used in the development of the full-scale commercial remedial strategy for the site.INTRODUCTION AND OVERVIEW OF PROJECT SMiRTWhile there are strong financial and environmental incentives to remediate and redevelop brownfield sites there are also barriers including fear of the unknown, regulatory control, delays, increased costs and the stigma associated with such sites. Hence the remediation process needs to be conducted in such a way to maximise the incentives and overcome the barriers, which is how deep mixing found its niche in the land remediation market. Soil mix technology is such a versatile technique that can perform a number of remediation treatments on the same site. These include low permeability in-ground barriers (cut-off walls), permeable reactive barriers (PRB), stabilisation/solidification (S/S) treatments, other additive related remediation, e.g. in-situ chemical oxidation and bioremediation, as well as soil amendments for greening and also ground improvement all on the same site (Al-Tabbaa et al, 2011). Placed in the context of alternative solutions, soil mix technology could potentially replace the five techniques shown in Figure 1, which would be required to deliver the same treatments mentioned above. Treatment trains strategy, where a combination of techniques in succession are used to both reduce the contamination levels and deal with residual contamination, is becoming common in land remediation and the use of one set of equipment to deliver this would bring about significant financial advantages. In addition, soil mix technology has many other advantages in terms of speed of implementation, elimination of exposure to contamination, elimination of off-site disposal and low cost. Soil mix technology for the remediation of contaminated land emerged in the UK in the mid 1980s and has since been employed in over 30 or so projects, which far exceeds its application to ground improvement for which only a handful of jobs have been carried out to date."

Jan 1, 2015

The quiet banks of the Maumee River in Toledo, Ohio, received a wake-up call July 16 as two smokestacks in the Marina District were leveled with dynamite. B&B Wrecking, Inc. of Cleveland contracted the project with the city to bring down the twin stacks, both measuring over 250 feet tall. The structures were part of the Toledo Edison Steam Plant and were erected nearly a hundred years ago. A week’s worth of preparation went into final planning, drilling and loading holes with over 80 pounds of explosives. The felling went precisely as planned as onlookers cheered as the stacks were reduced to rubble.

Jan 1, 2015

By Wu Jian-tao, LI Guo-wei

"The Cement Mixing Pile (CMP) quality assurance assessment is an important programme in evaluating the efficiency of foundation improvement. Coring is the current specified method of quality assessment in China which has the shortcomings of long cycle, high cost and low efficiency. The field and laboratory test show that the regular cone penetration test can only detect maximum of 4m of effective detection depth in CMP. In contrast, the method of cone penetration test in the reserved hole can detect the quality continuously along the pile at any depth. The tip resistance of reserved hole penetration in the 7th day has good linear relationship with unconfined compressive strength in the 28th day. The slope of linear relationship decreases with the increasing of clay particles content.INTRODUCTIONThe method of Cement Mixing Pile (CMP) is often used to improve soft soil foundation in highway construction, with the major purpose of reducing settlements under embankments (Bruce et al., 2000),which is a form of what is known as the Deep Mixing Method (Bruce et al., 2013). The CMP technology spread quickly in China in the 1980s. CMP quality assurance assessment is an important programme in evaluating the efficiency of foundation improvement. Coring is the current specified method of quality assessment in China (China Academy Of Building Research, 2002). The method of Coring is perceived in some quarters that samples will provide lower strengths given the distress caused to the core during drilling and extraction (Bruce et al., 2002).The cone penetration test CPT can provide continuous measurements of the penetration resistance, sleeve friction at the tip of the probe, which has advantages of simple operation, low cost and high efficiency compared with coring. However, CPT tests have not been established to assess CMP in Sweden because of difficulties in maintaining verticality (Larsson, 2005). In Finland and Norway, however, CPT tests are commonly used (Halkola, 1999). One of the disadvantages of CPT is the tendency of the cone to steer out of the column (Porbaha et al., 2003). Darya Mokrousova (2010) states this tendency to deviate can be overcome by pre-boring and starting the penetration test from the base of the pre-bored hole. Sheng Haiyang (1999) found that probes may be deflected out, sometimes even at small penetration depths, and may not give a complete inspection of the pile. Liu Songyu et al. (2003) suggested that the Standard Penetration Test (SPT) is an effective way to evaluate the strength and quality of stabilized soil-cement columns. In general, Regular CPT can’t test the full length of CMP, and SPT still needed drilling which causes discontinuous detection. From the existing standard of China, core sampling compressive strength test is the main method, evidently, coring displays a longer test cycle, high cost and low efficiency. Therefore, an improvement of CMP quality assessment, by conjuring a fast and reliable detection and evaluation method, is necessary. The aim of this paper is to research the feasibility of using CPT in assessing the quality of CMP and presents an improved CPT method."

Jan 1, 2015

By D. M. Maijer, S. M. Mohseni, A. B. Phillion

The microstructure evolution kinetics of aluminum alloy B206 during artificial aging has been investigated using non-isothermal calorimetry. A combination of differential-scanning calorimetry (DSC) and tensile tests have been utilized to develop an Avrami model to predict the precipitation kinetics as a function of the thermal processing parameters. The Avrami coefficients, found based on a Kissinger analysis, compare well against those reported in the literature for aluminum-copper alloys. The rapid precipitation kinetics predicted by the Avrami model at temperatures higher than 200°C were assessed through a qualitative comparison against hardness measurement results. In contrast to the continuous hardening observed at 150°C, the material softens with continuing heat treatment at 250°C resulting in an overaged state. This can be attributed to the rapid precipitation kinetics at this temperature, leading to the termination of the precipitation-hardening effects at early stages of artificial aging.

Jan 1, 2015

By Charles M. Wilk

"Mass stabilization involves mixing binding agents into marginal or contaminated soil to improve the subject material’s physical and/or chemical properties. This paper concentrates on the principles of soil mixing and benefits and application to new and existing rail right-of-way. Successfully applied in Scandinavia and other European countries, the soil mixing is now being applied in right of way in the northern latitudes of the U.S. and Canada. These regions have significant areas of “peaty” soils that can complicate construction and maintenance of rail and structure foundations. Mass stabilization can be used to improve the bearing strength of these soft soils for subsequent construction of railroads, pipelines, roads, and buildings. In civil engineering, the technology is often used to improve the construction properties such as bearing strength, of a marginal soil. In environmental engineering, stabilization is remediation treatment technology that protects human health and the environment by immobilizing hazardous constituents within the treated material. . The treatment is conducted while the subject material remains in-place (insitu). Mass Stabilization is often used to accomplish both civil and environmental purposes on the same project effectively addressing marginal soil while eliminating the expense of soil removal and replacement. This paper presents the principles of mass stabilization technology, implementation in the field and recent completed railway projects. The example rail projects will present the various benefits that soil mixing provides to railway construction and maintenance. Bench-scale studies and full scale implementation as well as soil construction properties before and after mass stabilization will be discussed. The paper and presentation will include information on the advantages of mixing methods and binding agent delivery systems.INTRODUCTIONNew or existing railroad right-of-ways may cross ground with low bearing capacity. Right of way subgrade undergo deflection (strain) as loads (stress) are applied. The amount of strain or deflection of the subgrade caused by loading of a train is proportional to the stiffness of the subgrade materials. Some soils, such as tamped ballast, are very stiff and resist loads well. Other soils such as soft clay, peat, or loose sand have low stiffness and undergo substantial movement under loads. It is very desirable to have the stiffest possible material in a track subgrade. Stiff subgrade material limits deflection under load, reducing track roughness and occurrence of track defects. Mass stabilization is a geotechnical method that can be used to improve the bearing capacity or stiffness of soil in these right-of-way. Mass stabilization involves mixing binding agents into soil subject to treatment while the soil remains in-place or insitu. Variations in the design or areas subject to treatment can be used to address transmission of vibration to adjacent structures."

Jan 1, 2015

By J. P. Rider, T. W. Beck, J. A. Organiscak

"The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR) has recently developed a series of models utilizing Computational Fluid Dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations. CFD models utilizing Species Transport Model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The following scenarios are considered in this study: 100% of the discharge redirected back towards the face on the off-curtain side of the continuous miner; 100% of the discharge redirected back towards the face, but divided equally to both sides of the machine; and 15% of the discharge redirected toward the face on the off-curtain side of the machine, with 85% directed into the return. These models were compared to a model with a conventional scrubber discharge where air is directed away from the face into the return. The CFD models were calibrated and validated based on experimental data and accurately predicted sulfur hexafluoride (SF6) gas levels at four gas monitoring locations. One additional prediction model was simulated to consider a different scrubber discharge angle for the 100% redirected, equally divided case. These models identified relatively high gassy areas around the continuous miner which may not warrant their use in coal mines with medium to high methane liberation rates. This paper describes the methodology used to develop the CFD models, and the validation of the models based on experimental data.INTRODUCTION Methane gas and respirable dust are two hazards frequently encountered at continuous miner (CM) operations. An accumulation of both methane gas and coal dust may lead to massive explosions underground [1], and overexposure to respirable coal dust can result in pneumoconiosis (commonly referred to as “Black Lung Disease”) in coal workers [2]. Current U.S. federal coal mine regulations limit concentrations of methane gas to below 1% at the face area and require exposures to respirable coal dust to be at or less than 2.0 mg/m3 for an 8 h shift average. Begin on August 1, 2016; the overall respirable dust standard in coal mines is reduced from 2.0 to 1.5 mg/m3 for full shift sampling. If the quartz content of the dust exceeds 5% by weight, the dust standard becomes more stringent, reducing the allowable concentration to the value of 10 divided by the % quartz."

Jan 1, 2015

By Cristian Rodriquez, Fernando Fernandez, Rodrigo Fuentealba, Tom BoBo, Maria Rocha, John Kemeny

This paper describes a case study that was conducted at a new mine in South America. This mine has significant geologic variations that will result in different distributions of hard and soft ore being mined at different periods of time over the mine life. A study was conducted to determine the optimum blast design that will meet the mill throughput requirement of 95,000 tonnes (104,720 tons) per day for the first 10 years of the mine life. As part of this study, field rock mass characterization and laboratory tests were conducted. This includes standard rock mechanics tests as well as rock breakage tests used in mill simulations. The geology of the ore body was broken up into four Geologic Units, and statistical variations in the properties were determined for each unit. Using this data along with the data on the occurrence of the different geologic units over time, simulations were made of the run-of-mine (ROM) fragmentation due to different blast designs, and these results were used in simulating the resulting throughput after crushing and grinding. Four blast designs were considered with powder factors of 0.44, 0.54, 0.64 and 0.94 kg/t. The results of this study show that determining the proper blast design is important in ensuring that the mill throughput requirement will be met over the mine life.

Jan 1, 2015

By W. Standifird

"Cohesive fracture is a mechanical model widely used for modeling quasi-brittle fracture in rocklike materials. This work discusses use of this model to simulate quasi-brittle fractures generated by injection stimulation during the process of cuttings reinjection in West Africa. Cuttings reinjection is an engineering practice used for disposal of drilling waste. During this process, hydraulic fractures are created at the target formation and milled cuttings are injected with fluid. In practice, this process must remain in compliance with environmental regulations and zero-discharge policies. The purpose of this study is to determine the following factors of injection design for a field in West Africa: (1) pumping pressure capacity required to successfully perform the injection and (2) the injection rate for injection performance and the value of fracture width under injection.A simplified three-dimensional (3D) finite element model (FEM) was built. A poroelastic plastic damage model was used for simulation of the cohesive crack prorogation within the target formation. For simplicity, fracture development in both horizontal and vertical directions was simulated separately. In this way, the computational burden for one calculation was reduced to a reasonably low level, without losing accuracy of the model. Loads of the model include fluid injection and gravity, which balances the initial geostress field. Various values of injection rate were used in these calculations to determine the most reasonable value of injection pressure. The capacity of pressure of a pumping device was determined using this optimized value of injection pressure.Results in values of width and length of fractures created by the injection are presented. Injection pressures at bottom-hole (BHP) corresponding to each value of injection rate are also given. Numerical results for fracture generation and propagation in a horizontal direction were visualized. The pumping pressure capacity required to fulfill the cuttings reinjection work was determined based on the numerical results of optimized injection rates and pressure. The fracture width was determined using the given pumping pressure. The length and height of the fractures was determined using pumping pressure along with the required volume of cuttings waste to be disposed of into the formation.This work presents a case study of 3D finite element modeling of hydraulic fracturing generated by cuttings reinjection. The results of the optimized injection rate and pressure provide a best practice and a useful reference for cuttings reinjection analyses in this region."

Jan 1, 2015

By A. Mazhary

"Although ore sorting in mining is not a new concept, sensor-based sorting has failed to gain broad acceptance due to perceived challenges with the technology. In order to gain wider applications, this research focuses on treating waste rock and low-grade ore to identify and test appropriate sensors and to evaluate the response. Results showed that amenability of rocks to sensor-based ore sorting is both sensor and ore specific. It was also observed that the efficiency (recovery) of sorting is directly influenced by the degree of heterogeneity of the rocks. The overall outcome showed that with the right sensor, several of the materials tested are amenable to sensor-based ore sorting. Mining companies could benefit from multiple economic and design impacts, such as lower energy cost, lower transportation costs, higher metal recoveries and smaller footprints that lead to more sustainable mining. This paper will focus on the effects of heterogeneity of rocks on sorting potential and efficiency.IntroductionSensor-based ore sorting has been attracting more attention since the pressure for effective resource extraction and management has increased. An urge to make most of the current deposits, and to make the low-grade deposits economic to mine has ushered the technology to find new ways to overcome the new challenges. No matter the terminology used, such as coarse beneificiation, waste rejection, particle or bulk sorting, the purpose of sensor-based ore sorting is to remove low-grade rocks before the comminution circuit, increasing the feed head grade and quality while reducing the energy costs related to comminution.Despite nominal advantages, there have always been some concerns that have impeded the intorduction and acceptance of the technology. One of the most important shortcomings of ore sorting is their capability, or capacity, to keep up with the high-tonnage mining. Some other issues that have been mentioned as drawbacks to sorting include installation cost of such devices, feed preparation for effiecient sorting along with accuracy of sorting and probability of false negatives (Manouchehri, 2003)."

Jan 1, 2015

By Ed McConaghy, P. LaRochelle

The Ambatovy Nickel Project comprises the development of mine, hydrometallurgical processing facilities and necessary infrastructure in Madagascar, positioning Ambatovy as one of the world’s largest producers of nickel and cobalt from lateritic ore. SNC-Lavalin successfully provided comprehensive Engineering, Procurement, Construction Management (EPCM) services for this major capital project which, apart from its sheer size, scope, and engineering design, represented significant location, infrastructure, labour, environmental and climatic challenges. Today, the project has reached 90% of its nameplate capacity and is in its final performance optimization stage. This paper will discuss the significant project management effort that was required to successfully address the complexity of this major project. It will cover the main project management control systems and the engineering tools and processes used during the detail engineering, procurement, and construction phases to achieve optimum project execution.

Jan 1, 2015

By E. C. de Beer

"SynopsisA number of important areas in nuclear fuel cycle, at both the front end and back end, offer ideal opportunities for the application of non-destructive evaluation techniques. These techniques do not only provide opportunities for non-invasive testing of e.g. irradiated materials, but also play an important role in the development of new materials in the nuclear sector. The advantage of penetrating radiation used as probe in the investigation and testing of nuclear materials makes X-ray and neutron radiography (2D) and tomography (3D) suitable for various applications in the total nuclear fuel cycle. The unique and different interaction modes of the two radiation probes with materials provide several opportunities. Their complementary nature and non-destructive character makes them most suitable for nuclear material analyses, analytical method development, and the evaluation of the performance of existing nuclear material compositions. This article gives an overview of the X-ray and neutron radiography/tomography applications in the field of nuclear material testing, and highlights a few of the success stories. Several selected areas of application in the nuclear fuel cycle are discussed to illustrate the complementary nature of these techniques as applied to nuclear materials.IntroductionDuring the development of new materials for the nuclear industry, materials testing and characterization are of the outmost importance to maintain safety standards and reliability. No compromise on safety in the workplace in any area within the total nuclear fuel cycle can be tolerated, and therefore most in-situ material characterization and testing is conducted by certified and qualified personnel schooled in destructive and non-destructive testing (DT and NDT) methods. Certification and qualification in NDT can be obtained through many training centres in South Africa in accordance with European, American, and other international standards (SGS, n.d.; SAIW, n.d.; African NTD Centre, n.d.)."

Jan 1, 2015

By H. Huang, R. N. Gow

"Previously, Gibbs’ phase rule was applied to mass-balanced EH-pH diagrams for the Cu-As-S-H2O system. Diagrams were generated using the stoichiometry of enargite as a basis. In this study, the calculations were expanded to cover the stoichiometries of three other Cu-As-S minerals (tennantite, sinnerite, and lautite) and compared to enargite. Stability regions within the resulting EH-pH diagrams were found to change with stoichiometry such that a particular mineral would predominate if its stoichiometry was used in the calculation. Solution speciation was also found to vary, with thioarsenate being the best example. This stoichiometric effect helps to explain results reported in the literature and would be difficult to realize if it were not for mass-balanced calculations. INTRODUCTION A comprehensive thermodynamic review has recently been conducted on the aqueous copper-arsenic-sulfur system (Gow et al., 2014a-d). The free energies of over 100 species were collected from various authors and thermodynamic databases to produce mass-balanced EH-pH diagrams, using the thermodynamic equilibrium calculation software, STABCAL (Huang, 2014). The full database was listed and discussed by Gow et al. (2014A). Resulting diagrams were generated for enargite and confirmed with Raman spectroscopy using bulk mineral electrodes in order to identify reactions spectroelectrochemically. Theoretical calculations agreed well with the experimental results under alkaline conditions (Gow et al., 2014a), acid conditions (Gow et al., 2014b), and alkaline sulfide leaching conditions (Gow et al., 2014c). In this study, additional mass-balanced EH-pH diagrams are generated by changing the copper-arsenic-sulfur stoichiometry from enargite (Cu3AsS4) to tennantite (Cu12As4S13), sinnerite (Cu6As4S9) and lautite (CuAsS). Regions for the thermodynamically stable species are shown to change with the four different mineral compositions. Potential leach conditions, both for co-dissolution and selective dissolution techniques, were examined for differences in predominant species according to changing copper-to-arsenic ratios, sulfur compositions, and sulfur oxidation states."

Jan 1, 2015

By Shi Hongchao, Zou Zou Xinkuan, Zhang Jichun

As drilling and blasting is carried out in an urban tunnel, which is adjacent to an existing building or structure, the balance between blasting-induced vibration reduction and drivage efficiency is a most important issue that must be resolved properly. Therefore, a new cut blast method named Stepped V-cut millisecond blasting (SV-cut) was developed by optimizing the most common used Vertical V-cut blasting method (V-cut). The most significant features of SV-cut lie in the utilization of sublevel interval charging structure and millisecond delay blasting technology in cut hole and the cut-cavity formed from outside to inside sequentially. SV-cut provides advantages of high borehole using ratio, low vibration level, and satisfied advance per attack. Based on the principal of millisecond blasting, the rock fragmentation process and the vibration reduction mechanism of SV-cut are analyzed. Determining methods of blasting parameters, which do have significant effect on vibration intensity and cut-cavity formed quality, are proposed according to the forming requirement of both outer and inner cut-cavity and vibration reduction. In order to compare the performance between SV-cut and V-cut, field blasting experiments were performed in the blasting engineering of Yamalike twin-arc tunnel, which closely passes over aged parallel tunnels. Blasting results show that SV-cut blasting is proven as an effective tunnel blasting method for both increasing blasting effects and decreasing blasting vibration. Comparing SV-cut with V-cut, the SV-cut can increase blasting drivage about 8.5% and reduce the vibration intensity induced by cut hole blasting 30% at least.

Jan 1, 2015