Search Documents

By Jae-Chun Lee, Sadia Ilyas

"The present study was carried out to develop an economically feasible and environmentally friendly technique to extract metals such as Al, Fe, Cu, Zn and Ni from electronic scrap by employing Penicillium chrysogenum strain KBS3. Studies were carried out in various leaching modes, including one-step leaching with combined growth and leaching phases (Mode 1), two-step leaching with alternative growth and leaching phases (Mode 2), spent medium leaching with separated growth and leaching phases (Mode 3), leaching with fresh growth medium without fungal culture (Mode 4), leaching with deionized water (Mode 5) and leaching with commercial organic acids (Mode 6). The main lixiviants produced in leaching Mode 1 were citric, tartaric, oxalic and gluconic acids in concentrations of 12, 2.5, 1.8 and 152 mM, whereas in leaching Mode 2, the concentrations were 15, 0.5, 1.0 and 1,162 mM, respectively. In leaching Mode 3, 63 mM citric acid, 23 mM tartaric acid and 29 mM oxalic acid was observed. At 5% pulp density, both leaching Modes 1 and 2 showed similar metal extraction yields from the electronic scrap at 35º C. Approximately 96% Al, 98% Zn, 48% Cu, 25% Fe, 66% Pb and 73% Ni were extracted in leaching Mode 1 in 14 days. In leaching Mode 3, 85% Al, 81% Zn, 97% Cu, 22% Fe, 50% Pb and 63% Ni were extracted in 14 days. The extraction yield of Cu was much lower in leaching Modes 1 and 2 (48- 50%) than in leaching Mode 3 (97%), as well as in leaching Mode 6 (98%) with organic acids, including citric, tartaric, oxalic and gluconic acids.IntroductionTechnical innovations in electrical and electronic equipment with new functionalities and designs stimulate consumer purchasing and lead a rapid increase in the production of waste materials. Terazono et al. (2006) have reviewed the data on electronic waste generation in different parts of the world. Studies by Bertram et al. (2002) have also affirmed that waste electrical and electronic components are the fastest growing waste category, which emphasizes the need for efficient recycling strategies. The recycling of electronic waste is an important subject, not only from the perspective of waste treatment, but also from the perspective of the recovery of valuable materials. However, the recycling of electronic scrap is still limited, due to the heterogeneity of the materials present in the products (Veit et al., 2005).Bioleaching-based processes offer a number of advantages over conventional pyro or hydrometallurgical methods (Lee et al. 2007; Lee and Pandey, 2012). These advantages include simple, inexpensive (in some cases) and ecofriendly approaches and the generation of less active leach residue relative to other metallurgical processes. Although biohydrometallurgical processes have been successfully applied to the leaching of metals from ores (Olson et al., 2003; Rawlings, 2002), data pertaining to the application of these processes for the extraction of electronic scrap are still scarce. Recently, a few studies have been undertaken for the extraction of metals from electronic scrap/ printed circuit boards (Brandl et al., 2001; Faramarzi et al., 2004; Ilyas et al., 2007; Ilyas et al., 2010). These studies were conducted with mesophilic chemolithotrophic bacteria (Acidithiobacillus ferooxidans and Acidithiobacillus thiooxidans), cyanogenic bacteria (Chromobacterium violaceum) or moderate thermophilic bacteria (Sulfobacillus thermosulfidooxidans). However, compared to bacterial leaching, fungal leaching has several advantages, including (i) the ability to grow at a higher pH, thus making it more suitable for the bioleaching of alkaline solid waste; (ii) a generally faster leaching process with a shorter lag phase and (iii) the chelation of excreted metabolites (e.g., organic acids) with metal ions, thus reducing toxicity to the biomass (Burgstaller and Schinner, 1993; Aung and Ting, 2005)."

Jan 1, 2015

By Jay P. Tobin

This paper will address the legal standards applicable to construction blasting lawsuits and offer best practices suggestions for pre-blast inspections, documenting the construction blasting work, recordkeeping, and effectively participating and partnering in the defense of a construction blasting lawsuit.

Jan 1, 2015

By P. James

"INTRODUCTION Dissolved salts build up in leach solutions over time as leach solutions mature. Iron can be particularly problematic for hydrometallurgical copper production as it can compete with copper for separation during solvent extraction (SX), leading to iron bleed through and reduced electrowinning (EW) efficiency. In its ferric form (Fe+3) it precipitates as a hydroxide at fairly low pH and can promote clogging and disrupted flow within leach pads as a result of localized pH deviations – such as might result from weather events. The solids formed can cause relatively irreversible degradation to pad productivity. The precipitation pH point for solids formation falls as the ferric (Fe+3) concentration increases, making the issue more prevalent as leach circuits for ore bodies containing appreciable iron get older. It can also be more of a concern when leaching lower grade ore like tailings where lower copper content may increase iron/copper ratios which may increase iron accumulation rates. The precipitation pH point for solids formation falls as the ferric (Fe+3) concentration increases, making the issue more prevalent as leach circuits for ore bodies containing appreciable iron get older. It can also be more of a concern when leaching lower grade ore like tailings where lower copper content may increase iron/copper ratios which may increase iron accumulation rates. Control of ferric (Fe+3) levels could be used to lower ferric (Fe+3) levels and keep the ferric hydroxide [Fe(OH)3] precipitation pH sufficiently high to avoid the associated solids formation and potential leach pad occlusion. Control of ferric (Fe+3) and ferrous (Fe+2) tenors and ratios may also provide benefit for improving sulfide ore leaching or bioleaching performance and effectiveness. Traditionally options for such control were rather limited with bleeding contaminants off or chemical dosing treatments being prominent methods. Now Blue Planet Strategies introduces a new option. Blue Planet Strategies (BPS) focuses on improved resource utilization targeting electrolytic treatment and waste conversion into resources and has now demonstrated that its proprietary DeMet™ (Dynamic Electrolytic Metal Effluent Treatment) platform is highly effective at efficient low-cost conversion and control of iron content in leach streams in addition to targeted dilute metal recovery.[1-6] This powerful new capability provides a new treatment opportunity to control leach solution ferric (Fe+3) and ferrous (Fe+2) tenors to enhance leach operation production."

Jan 1, 2015

By W. Lin, Z. Z. Dong, C. L. Zhou, Y. C. Kuang

The inversion of rock mechanical properties based on well-logging data is a common method to drillbit selection in petroleum engineering, the basic principle of which is to use deep-well logging data and experimental regression model to calculate rock mechanical properties. The profile of rock mechanical properties can be established. According to the profile, the type of drillbit can be selected in different formations, which will improve the economic benefit of bit use indicators. Compressive strength of rock is one of the most important parameters. Conventional method to establish regression models of acoustic velocity and uniaxial compressive strength is on the basis of rock core sonic experiments and uniaxial compressive experiments. However, with the increase of deep drilling operation, triaxial compressive strength prediction model will play a more vital role in drillbit optimization selection in deep wells and improving ROP (Rate of Penetration). Triaxial compressive strength is an important parameter to evaluate the formation strength property. In this paper, to the sandstone commonly encountered in oil drilling, combined the rock mechanical experimental results with the changing porosity experimental results under confining pressure, a new interpretation model of triaxial compressive strength based on well logging data is proposed. Firstly, three types of sandstone samples are collected. Then measured components, uniaxial compressive strength, triaxial compressive strength and porosity. Experimental results show that: confining pressure has a significant influence on sandstone strength, with the increase of confining pressure, triaxial compressive strength increase; furthermore, the triaxial compressive strength of different porosity sandstones have different change rules when confining pressures changes; sandstone porosity decreases with the increase of confining pressure and it obeys logarithmic function. According to the results, regression models of sandstone, in-situ uniaxial compressive strength model and uniaxial compressive strength model under normal pressure are generated. Meanwhile, using well logging data in the acoustic velocity, density and gamma value can derive in-situ rock formations uniaxial compressive strength and in-situ porosity. Eventually, a new model established in this paper, containing in porosity, uniaxial compressive strength, lateral pressure and power exponent of regression, can predict triaxial compressive strength which will guide drillbit selection.

Jan 1, 2015

By Tassos Grammatikopoulos, Vladimiros Papangelakis, Douglass Duffy, Cheryl Washer, Srinath Garg

Flotation operations in Sudbury, Ontario, seeking to separate pentlandite and chalcopyrite from mixed sulphide deposits, produce pyrrhotite tailings that have been disposed of in tailings ponds for over 50 years. These reactive tailings are viewed as waste, despite containing ~0.8 wt% Ni, and represent an environmental liability because of their acid mine drainage (AMD) potential. Given the large quantities of pyrrhotite currently stored in Sudbury, and declining ore grades elsewhere, these tailings have shifted from being viewed as a waste to a potential resource. Recent advances in the bioleaching of low-grade sulphide ores have raised the prospect of bioleaching as a potential low-cost processing option. However optimization of this proposed process requires a thorough understanding of the mineralogy of the pyrrhotite tailings that would be leached. The work presented here addresses the characterization of two distinct Sudbury pyrrhotite tailings, namely from the Vale and Glencore operations, using electron microprobe, XRD and QEMSCAN analysis. Particular focus is given to how the mineralogy may affect bioleaching as a processing option, through the deportment of nickel and the various phases present

Jan 1, 2015

By Jerry Gagnon, Matt Burr, Dave Evans, Timothy Ellis, Davies Kakengela, Abbas Mirza, Larry Webb, François Leclercq, Andrew Johnston

Lead-based alloys are the primary anodes used in electrowinning from sulphate-based aqueous systems. Lead anode technology has evolved over the years, migrating from pure lead and lead-antimonial alloys to the present day lead-calcium-tin alloys for copper electrowinning and lead-silver alloys for zinc electrowinning. It has also migrated from cast to rolled microstructures in search of improved mechanical properties and higher corrosion resistance. Although great strides have been made in the development of new alloys and production processes, the industry still has unresolved issues related to untimely corrosion which limits anode life and may lead to higher contaminant levels in the metal being produced. Lead anodes corrode because of the difference in the chemical/electrochemical potential across the microstructural features of an anode. Given a very high purity material, we find that the grain boundary areas corrode significantly faster than the rest of the grain. The desire to minimize grain boundary corrosion by a balance of alloying element selection and microstructural design allows the grain boundary area to be engineered. However, operational issues can lead to unexpected corrosion behaviours which we will discuss moving forward. The comments in this work, though directed toward copper electrowinning, can be extended to similar phenomena in other metals electrowon from sulphate media (i.e., zinc, nickel, cobalt, manganese). The lifecycle of electrowinning anodes is dependent upon electrowinning tankhouse operating conditions and maintenance of the anodes, including cleaning and straightening. This paper will focus on the operational aspects of maximizing the utilization of lead electrowinning anodes.

Jan 1, 2015

By L. G. Stolarczyk, J. Duncan

"SynopsisLong before the environmental movement, coal miners were suffering from occupational diseases that became apparent in the later years of service, and especially during the retirement years. Chronic exposure to micro-fine dust in the respirable range (‘float’ dust) causes various lung diseases, referred to as coal mine dust lung disease. In the USA alone, 76 000 miners have died of coal mine dust lung disease since early legislation recognized the issue in 1969. Researchers believe that reducing float dust exposure limits alone will not reverse the increasing incidence of coal mine dust lung disease seen in the current generation of miners. Trace and radioactive metals are concentrated in the thin boundary layers of the coal seam (Roberts, 2013), and hence float dust includes silica and toxic trace metals. The production and quality of coal is also significantly impacted by the presence of these contaminants in the coal. In the combustion process, the trace metals are oxidized and become incorporated in the fly ash and flue gas. Since they are extremely water-soluble, they represent a significant danger to health and the environment. Coal preparation plants and power stations need to mitigate these contaminants as far as is practical, but the simple fact is that most contaminants should have been left un-mined.This paper describes an innovative coal-cutting solution to the longstanding technology gap in mining – the ability to measure uncut coal layer thickness to the boundary rock layer. Because of constant changes in geology, seam thickness, and seam undulation, the horizon sensor must be located in the bit-block of the rotating cutter drum of the mining machine. Contaminants in ROM coal must be minimized at the source – that is, at the rock/coal crushing cone directly under the bit-tips of the cutting drum. Bittip distances to the rock boundary layer must be automatically controlled in real time when mining in a complex and undulating coal bed. Horizon sensing (HS) technology enables the mining machine’s cutting picks to stop at a specified distance from undulating horizons of the boundary rock. The thin contaminated coal layer can be left in situ, significantly reducing the toxicity of the float dust. Preventing the metal picks from striking quartz-containing boundary rock also reduces the occurrence of methane ignitions. HS technology equipped with pick force vector sensing can allow optimization of the cutting pick lacing pattern for minimum coal and rock crushing, thereby reducing float dust. This technology may enable the mining industry to convert from automated machine control to autonomous during coal cutting and loading."

Jan 1, 2015

By Y. I. Yang, Y. -B. Tang, D. -J. Ma

Chlorine-containing minerals are commonly present in coal. Associated minerals such as pyrite can undergo exothermic reactions. Consequently, it is of great significance to study the effect of inorganic chloride on the spontaneous combustion of coal. In this study, the effects of five inorganic chlorides (sodium chloride, magnesium chloride, potassium chloride, calcium chloride, and zinc chloride) on the spontaneous oxidation of coal were investigated. Analysis of the gaseous products of coal oxidization at low temperatures (323K to 453K) showed that the presence of inorganic chlorine in coal markedly decreases O2 consumption and the generation of CO and CO2. Samples of raw coal and chlorine-loaded coal were oxidized for 36 hours under the same experimental conditions. Infrared diffuse reflectance spectroscopy results showed that inorganic chloride can inhibit the oxidative decomposition of some functional structure components (methyl, methylene, methine, and hydroxy) in the coal. The influence of inorganic chloride on the oxidation characteristics of the functional groups in coal during spontaneous combustion was investigated using benzyl alcohol and 1-phenylpropanol as model compounds, which were tested under the same experimental conditions as the coal samples. The oxygen consumption of model compounds with and without the addition of inorganic chloride further suggested that inorganic chloride may hinder the oxygenolysis of these structures during low-temperature oxidation. This phenomenon can be attributed to the radical reaction from the perspective of radical chemistry. It can therefore be concluded that inorganic chlorides play an inhibitory role in the spontaneous combustion of coal.

Jan 1, 2015

By Z. Zhong, Y. J. Hu, D. Elsworth

"A standard triaxial apparatus was set up to perform sliding tests. Slide-hold-slide (SHS) tests, with hold times from 10 to 3000s and at invariant effective confining pressures of 1MPa, incremented to 3MPa and then 5MPa, were conducted on both dry and wet split limestone samples to study the evolution of fracture friction under holding and sliding processes. Limestone fracture shows time-dependent behaviors in SHS tests, friction drops (creep) gradually during hold periods, and recovers (healing) after re-slide. Frictional healing and creep increment are proportional with hold times, while are inversely proportional with effective confining pressures. Moreover, the wet sample displays heavier healing than the dry one, whereas creep increment of the wet sample is lighter than the dry one. We conclude that the evolution of limestone fracture friction is significantly controlled by mechanisms of fluid-rock interactions.INTRODUCTIONThe evolution of the mechanical properties of fractures and faults exerts a critical influence on the behavior of fault zones and on the earthquake cycle. In addition to natural processes, this behavior has broad implications in induced seismicity and influences oil and gas production, the sequestration of carbon dioxide and the disposal of nuclear wastes.Fault friction is typically measured by slide-hold-slide experiments, where fault gouge is deformed at low velocities (<0.1 mms-1) and over small shear offsets (<30 mm) (Dieterich, 1979, 1981; Mair et al., 1999; Marone, 1998, 2004) or alternatively with rotary-shear devices, that enable higher slip velocities over very large shear offsets (Hirose & Shimamoto, 2005; Mizoguchi et al., 2006). Typical experiments (Dieterich, 1972; Marone, 1998; Olsen et al., 1998; Bos & Spiers, 2002; Tenthorey et al., 2003) show significant creep during the holding period and frictional healing (strength gain) upon reloading. Fault creep and healing are often time-dependent with longer hold times typically resulting in greater magnitudes of creep and in strength gains (Tenthorey et al., 2003; Yasuhara et al., 2005; Carpenter et al., 2012). Frictional healing may arise from growth of grain contacts (potentially induced by pressure solution) (Rabinowicz, 1951; Dieterich & Kilgore, 1994; Yasuhara et al., 2005), strengthening of the contacts (correlates with cementation) (Hickman & Evans, 1992; Beeler et al., 1994; Karner et al., 1997; Olsen et al., 1998; Muhuri et al., 2003; Tenthorey et al., 2003; Li et al., 2011) or via other changes in state including changes in porosity and rearrangement of force chains. Experimental evidence (Dieterich, 1979, 1981; Johnson, 1981; Marone & Scholz, 1988; Marone, 1998; Saffer & Marone, 2003; Moore & Lockner, 2007; Ikari et al., 2007; Ikari et al., 2011; Carpenter et al., 2012) quantifies both the mode and magnitude of second-order changes in the velocity-dependent (including velocity- strengthening and weakening) evolution of frictional strength."

Jan 1, 2015

By V. Shumila, T. Butler

Microseismic monitoring systems listen to a rockmass and record ground vibrations associated with brittle rock fracture. Modern systems record continuously and can identify as many as one thousand small and possibly larger magnitude events occurring each day from induced stress change and redistribution. This paper presents examples of the real time use of microseismic information in mining applications. It shows how alerts can quickly identify large magnitude events or unexpected clusters of seismicity and how seismic re-entry protocol can help to improve safety decisions. Additionally, newly developed advanced analysis techniques applied to mine seismic data sets are shown including the use of clustering methods to see into a cloud of seismic data to identify significant activity and quantify possible planar features. The use of source parameter trend analysis is shown to be a beneficial method for interpreting changes in relative stress levels. Seismic moment magnitude distributions are analyzed using the TGR (Truncated Gutenberg Richter) and TMD (Tapered Moment Distribution) methods to estimate bvalue and expected maximum magnitude. Seismic hazard analysis is shown as a useful way to simplify a dataset and highlight seismic hot spots. The rockmass response to excavation is a complicated spatial and temporal process and microseismic monitoring is a method that can be used to help understand the location and mechanics of failure occurring in the rock ultimately helping to improve safety and productivity at a mine site.

Jan 1, 2015

By M. Bustin, A. Hosseinian, G. Preisig

Hydraulic fracturing and hydraulic shearing techniques are essential for the development of unconventional oil & gas and geothermal resources. Such techniques will also play a key role in the development of CO2 sequestration, and management of high stresses encountered with deep mining. However, the optimal design of hydraulic injections is often limited by continuum treatments of the rock mass without consideration of the influence of the natural fractures present. These may interact with the hydraulic fracture to promote offsets or arrest, or may cause the natural fractures to undergo shear and dilation. Given the limited access to the rock afforded by deep boreholes common to oil & gas and geothermal projects, advanced numerical modeling is critical for understanding key mechanisms and interactions. In this work, we first present a coupled hydromechanical distinct-element model focusing on the propagation of a hydraulic fracture. Normal and shear displacements arising from the generated hydraulic fractures are subsequently integrated into a fracture flow model for detailed analysis of specific flow behaviour and fracture permeability. For this, a scanned 3-D profile of a natural fracture is used to correlate surface roughness to dilation as a function of shearing. Fracture flow is computed at different time steps corresponding to different fracture propagation states and geometries. Modeling results indicate that the opening of a tensile hydraulic fracture is accompanied by millimetre-scale shear displacements associated with slip and wedging between adjacent blocks. This may leads to a mismatch between the upper and lower walls of the fracture if asperities are irregular and strong enough. However, fluid-induced tensile fractures have low Joint Roughness Coefficients (JRC), and associated millimetre-scale shear displacements are too small to ensure a significant offset of asperities that prevent a fully-elastic closure when the hydraulic fracture is depressurized. Injection of proppant is thus critical to keeping hydraulic fracture apertures open. Future work is planned that will see the models calibrated against field data including microseismic event locations, magnitudes and source mechanisms, tiltmeter deformations, stress change, and pore pressures.

Jan 1, 2015

By L. J. Han, Y. J. Zong, S. Y. Wen, J. J. Wei

"Stress strain curves characteristics, deformation and strength properties, and failure process and characteristics of sandstone samples under different stress states were analyzed through triaxial compression tests carried on using TAW-2000 microcomputer control electro-hydraulic servo rock triaxial test system. The experimental results reveal that peak strength, residual strength, elasticity modulus and deformation modulus increase linearly with confining pressure, and failure models transform from fragile failure under low confining pressure to ductility failure under high confining pressure. Macroscopic failure forms of samples under uniaxial compression was split failure paralleling to the axis of samples, while macroscopic failure forms under uniaxial compression was shear failure, the shear failure angle of which decreased linearly with confining pressure. There were significant volume dilatation properties in the loading process of sandstone under different confining pressure, and then based on acoustic emission damage and volumetric dilatation damage the damage evolution properties of samples were analyzed, and damage constitutive model were established, realizing the real-time quantitative evaluation of samples damage state in loading process. INTRODUCTIONDamage is a phenomenon that micro defects in material under monotonic loading or reloading will lead to progressive decrease of the cohesion and damage of volume units. Many scholars at home and abroad have carried out systematic researchers on damage evolution characteristics and constitutive model of rock, and have achieved a series of remarkable results in this field. Lu Y.D. (2004) studied the complete stress-strain curve’s characteristics of marble under triaxial compression, and established the bilinear elastic-linear strain softening-residual ideal plastic damage constitutive model. Ren J.X. (2001) studied the damage evolution laws of coal and rock mass by computerized tomography triaxial loading system, realizing the quantitative evaluation of damage state. Zhang Z.L. (2011) studied the deformation and failure mechanism of strong weathered sandstone by triaxial compression test, and analyzed the damage evolution processes and established the damage evolution equations based on the density method. Li X.J. (2012) studied the microscopic damage characteristics of siltstone under triaxial compression by scanning electron microscope and digital image technology, and analyzed the statistical distribution characteristics of cracks azimuth angle, length, width. Zhou J.W. (2012) studied the strength, deformation and fracture damage characteristics of sandstone by uniaxial cyclic loading and unloading tests, and defined damage variable based on linear damage mechanics theory and acoustic emission (AE). Cao W.G. (2006) established a new damage model and a statistical damage constitutive model of rock under specific confining pressure according to the force of damaged part and undamaged part in rock on the base of statistical damage theory. Li S.C. (2014) studied the damage evolution characteristics in the whole uniaxial compression process of sandstone by electrical resistivity and AE, and proposed a status qualitative criterion for rock damage."

Jan 1, 2015

By R. Cammack

"A fundamental component of the Hoek–Brown empirical rock failure criterion is assessing an appropriate mi constant. In developing their empirical criterion Hoek and Brown normalised triaxial test results by dividing the principal stresses at failure by the uniaxial compressive strength to provide mi values for typical rock types. Experience shows that Hoek triaxial tests for individual lithology types commonly have a large inherent scatter. In addition, tests are often conducted on core from random locations, which although being of one parent rock type, display variations in density as well as minor variations in grain size and alteration.This paper presents experience from projects the authors have been involved in which large sample populations of triaxial and UCS tests on similar rock types were available. Geophysical logging data was also available for some projects. The methods used to estimate the compressive strength for each sample and the effects on normalising the data sets are described. The variability of the data and uncertainties and assumptions involved in the process of assigning a mi value from the normalised data are also discussed."

Jan 1, 2015

By V. Pawlowsky-Glahn, E. Pardo-Igúzquiza, J. J. Egozcue, R. A. Olea

Compositional data constitutes a special class of quantitative measurements involving parts of a whole. The sample space has an algebraic-geometric structure different from that of real-valued data. A subcomposition is a subset of all possible parts. When compositional data values include geographical locations, they are also regionalized variables. In the Earth sciences, geochemical analyses are a common form of regionalized compositional data. Ordinarily, there are measurements only at data locations. Geostatistics has proven to be the standard for spatial estimation of regionalized variables but, in general, the compositional character of the geochemical data has been ignored. This paper presents in detail an application of cokriging for the modelling of compositional data using a method that is consistent with the compositional character of the data. The uncertainty is evaluated by a Monte Carlo procedure. The method is illustrated for the contents of arsenic and iron in groundwaters in Bangladesh, which have the peculiarity of being measured in milligrams per litre, units for which the sum of all parts does not add to a constant. Practical results include maps of estimates of the geochemical elements in the original concentration units, as well as measures of uncertainty, such as the probability that the concentration may exceed a given threshold. Results indicate that probabilities of exceedance in previous studies of the same data are too low.

Jan 1, 2015

By Y. J. Yu, C. D. Zhang, Y. S. Zhao, W. G. Liang, Y. D. Geng, J. L. Bi

"In this study, the coefficient of thermal expansion (CTE) and thermal conductivity (TC) of shale in two perpendicular directions, vertical and parallel to the bedding of the rock, are firstly measured by experiment. The experimental results show that the CTE of the shale in the vertical direction is 1.69 times as much as that in the parallel direction, while the TC in the parallel direction is 1.83 times larger than that of the vertical direction. Based on the no initial strain assumptions, numerical simulations for the thermal cracking in shale are carried out with the obtained coefficients. Using finite element method and thermal-mechanical coupling theory, two fracture mechanical parameters, KI and J-integral of the shale are also analyzed for the shale thermal fracturing. The simulation results show that both KI and J-integral reach the maximum when the fracturing angle equals to 0° in the shale, namely parallel to the bedding direciton. It is also found that the two fracture parameters decrease with the fracturing angle increasing. Additionally, the thermal fracturing effect of the shale is evaluated under a given scenario. The study is significant for shale oil or gas recovery by in situ pyrolyzing method.INTRODUCTIONOil shale is regarded as a kind of unconventional resource that can contribute to production of shale oil and hydrocarbon gases (Rahm & Dianne, 2011). As is known that there is a large deposit of oil shale in China, and present technology for exploiting oil shale still concentrates on open-pit mining, obtaining shale oil by retorting shale on the ground (Li, Tang, Xue, Zheng, & Du, 2014; Qian, Yin, 2008). However, this technology has a bad effect on the environment and leads to severe resource waste for utilizing oil shale. Exploiting oil shale by in-situ method for ‘green mining’ is widely necessary in China (Kang, Wang, Cao, Liang, Chang, & Liu, 2013; Waters, Dean, Downie, Kerrihard, Austbo, & McPherson, 2009; Zoback, Kohli, Das, & McClure, 2012). One of effective method to exploit shale oil is heating oil shale in-situ underground. For instance, the in-situ conversion process (ICP technique) from Shell Company etc. used a direct heating method, and convectional heating oil shale underground by injecting superheated steam from Mining Technology Institute, Taiyuan University of Technology and constructing horizontal fracture in vertical wellbore from Chevron Company use indirect heating method (Chaudhary, Ehlig, & Wattenbarger, 2011; Hazra, Lee, Economides, & Moridis, 2013; Zhao et al., 2010). The convectional heating method contains complicated procedures with phase transition in double-media of fracture-matrix of oil shale subjected to multi-physical fields coupling including stress, fluid and temperature (Zhao et al., 2010). The characteristics of thermodynamics, solid mechanics and seepage of oil shale have been investigated separately (Hopkins, Rosen, & Hill,1998; Kang, Zhao, & Yang, 2008; Yang, Zhao, Kang, 2010; Zhao, Yang, Feng, Liang, & Kang, 2008; Zhao, Cao, Zhao, Lin, & Wang, 2008). However, it is quite difficult to solve constrained problem of each physical parameter in multi-physical fields coupling for oil shale pyrolysis."

Jan 1, 2015

By C. C. Li

Traditionally, strong and stiff devices, such as fully encapsulated rebar bolts and concrete lining and arches, are preferred for underground rock support. The attention is paid to the strength of the devices in such support designs. It has been observed in engineering practice that support systems composed of stiff devices are often subjected to premature failure in high stress rock conditions. In the past decade, yield support devices have been employed to improve the performance of rock support systems. A rock support system usually consists of both internal and external devices that are installed within the rock mass and on the free surface of the rock, respectively. Great efforts have been made to make support devices yieldable in the past years, but the efforts are focused on different aspects in the tunneling and mining branches. In the tunneling branch, the focus has been put on the development of external yield devices, such as Lining Stress Controller (LSC), Honeycomb element and compressible concrete, which are embedded in shotcrete liners, while in the mining industry the efforts has been on the development of yield rockbolts, such as the cone bolt and the D-Bolt. The internal and external support devices are not compatible in their deformation capacities in the current rock support systems even though yield devices have been employed. All the devices in a support system should be deformable and compatible in deformation capacity. With such a support system, premature failure of individual support devices could be avoided and the service life of the support system is prolonged. It is a trend at present to take into account the energy absorption capacity, instead of simply the strength, of support devices in rock support design.

Jan 1, 2015

By W. R. Reed, D. E. Pollock, T. W. Beck, J. A. Organiscak, J. D. Potts

"In underground continuous mining operations, ventilation, water sprays, and machine-mounted flooded bed scrubbers are the primary means of controlling respirable dust exposures at the working face. Changes in mining arrangements, such as, face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation, and equipment operator positioning, can impact the ability of dust controls to reduce occupational respirable dust exposures. This study reports and analyzes dust concentrations measured by the Office of Mine Safety and Health Research for both remote-controlled continuous mining machine operators and haulage operators at ten U.S. underground mines. Results of these respirable dust surveys show that continuous miner exposures varied little based on depth of cut, but are significantly affected by ventilation configuration. Haulage operators experienced elevated concentrations in blowing face ventilation. The type of cut influenced exposures, with elevated exposures observed for both continuous miner operators and haulage operators when working in crosscuts driven into, or counter to, the section airflow. Individual cuts are highlighted to demonstrate instances of minimal and excessive dust exposure attributable to particular mining configurations. These findings form the basis of recommendations for lowering face worker respirable dust exposures when performing a variety of continuous mining cuts.INTRODUCTION Underground continuous coal mining operations may encounter a wide range of conditions and arrangements during production and development activities. These activities typically produce respirable coal mine dust, putting operators of continuous mining machines and coal haulers at risk for elevated exposures. In order to comply with federal regulations limiting respirable dust exposures for the duration of a working shift, mine operators typically implement ventilation, water sprays, and machine-mounted flooded-bed dust collectors (scrubbers) to dilute and control mine dusts during coal cutting. Nevertheless, changes in operational conditions can limit the ability of these controls to effectively reduce dust exposures. Some examples of conditions that can change during the course of mining include face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation, and operator positioning. Because these arrangements are largely under the control of mine operators, any insight into associated exposures may inform future plans and behaviors, reducing occupational exposures to respirable dust. The objective of this OMSHR study is to evaluate respirable dust exposures associated with a range of continuous mining arrangements by comparing occupational dust concentrations measured during a series of field surveys. These comparisons consider face ventilation configurations, depths of cut, and crosscut mining practices."

Jan 1, 2015

By B. W. J. van Rensburg, M. J. Schmidt

Bulk materials handling systems are extensively used in the mining and minerals industry, where a fairly high incidence of structural failure is experienced, notwithstanding design compliance with appropriate standards. A number of case studies are explored to demonstrate how insufficient controls or protection systems have contributed to structural failures on mobile bulk handling equipment. The importance of design integration across engineering disciplines is highlighted. The revision of ISO 5049-1 (1994) is proposed to provide specific rules and guidelines pertaining to machine protection systems. It is further recommended that the structural design engineer of the original equipment manufacturer(OEM) fulfils a more prominent role during the final acceptance and handover of mobile bulk handling equipment, with specific reference to protection systems.

Jan 1, 2015

By Ali S. Fayad

"In June 2014, Orange County Flood Control District (OCFCD) completed construction improvements of the East Garden Grove-Wintersburg Channel for a price of $42 million. Instead of the pre-existing traditional trapezoidal levee, the channel was improved with a vertical compact levee. Dubbed Soil-Mix-Sandwich (SMS), this geo-structural and environmental solution for coastal channel improvements, underlain by liquefiable soil strata, was both a design and construction innovation. It employed Deep Soil Cement Mixing (DSCM) within the confines of a hydraulically-pressed (Giken Method) sheet pile duo. SMS was unique because it incorporated both subterranean and supra-dredge-line soil mixing within a very narrow workspace. Its DSCM pattern aimed at optimum densification of the workspace and was confirmed during the construction process. It availed the DSCM sub-contractor (Hayward Baker Inc.) the opportunity to demonstrate the fitness of their huge wet-mixing machinery within a very confined access-area and introduced approximately 70,000 cubic yards of DSCM within a limited 15 foot workspace width that stretched for a mile. The sheet pile duo created a construction-enclosure that became a stay-in-place load resisting system. PROJECT CHRONOLOGY AND LOCATIONAn Orange County Flood Control District (OCFCD) project-report was commissioned to study the East Garden Grove Wintersburg channel (OCFCD facility # C05). The report examined the hydraulic conveyance of the C05 channel and was concluded in 1994 by Williamson & Schmidt. The project-report did not encompass extensive geologic studies; but it provided several alternatives for channel improvement. It recommended a single row of sheet piles as the preferred alternative for the downstream reach.The most downstream reach of the C05 channel is located in an environmentally sensitive area, in City of Huntington Beach, California, USA. Its site includes seismic chasms that surface within the C05-footprint (the Newport- Inglewood tectonic fault). Extensive deposits of liquefiable soil exist beneath the channel. Furthermore, tidal-influence prevails against the channel levee. Implementation of a successful design for channel improvement emerged after several traditional concepts were deemed unacceptable by geotechnical consultants. OC Public Works (on behalf of OCFCD) was in need of a design and construction technique that mitigated many associated risks. From these circumstances, Soil-Mix-Sandwich was born and was referred to in the rest of this discussion as SMS. OC Public Works required the SMS design concept to undergo verification by independent geotechnical consultants. SMS chronology from conception to construction can be summarized as follows:"

Jan 1, 2015

By A. Tsekov, Stefan Neufeind, T. Angelov, G. Savov

"A complementary ion exchange/solvent extraction process for the recovery of copper from low-grade ores developed by Iontech Engineering Ltd. is described. It has successfully been implemented on a full-scale plant level at the Buchim Copper Mine in Macedonia, yielding a maximum copper cathode production of 2400 tonnes per year. Technical and economic aspects of three years of operational experience are comprehensively compared with the Asarel Medet copper plant in Bulgaria, which is utilizing conventional solvent extraction in the enrichment/purification step. INTRODUCTION The concentration and separation of copper from primary leachates is one of the key operations in the hydrometallurgical processing of oxide ores (Langner, 2011). Conventionally, this basic operation is conducted by submitting the pregnant leach solution (PLS), with a 1–5 g/L Cu content, from the initial sulfuric acid leach to a solvent-extraction (SX) process in which copper reports to the organic phase (see Figure 1). After phase separation, the metal is stripped from the extractant/diluent mixture employing sulfuric acid to furnish a concentrated metal solution, usually containing 40–50 g Cu/L. The final products of the overall process are copper cathodes, which are obtained from a terminal electrowinning step.Although considered as “technology of choice”, SX to date is still suffering from several drawbacks, such as the risk of poor phase disengagement and the high capital costs of solvent-extraction plants. Especially, the processing of leachates with lower copper tenors (< 1 g/L) is often economically less attractive. As a result, tremendous efforts have been dedicated to the evaluation of alternative technologies to address these challenges."

Jan 1, 2015