Search Documents

By Brandon Axelrod

This paper follows a student’s interest in explosives which began at an early age after watching a television program highlighting explosives engineering. The use of explosives in those programs led to curiosity about how one gets involved in the industry. These programs enticed the author to further investigate the explosives industry leading him to an explosives camp for high school students. After attending the camp, this passion further developed into postsecondary education.

Jan 1, 2015

By Carlo Sampaio, Moacir Veras, Aaron Young, Carlo Petter

"Three major challenges for the mining industry are the minimization of energy use, water consumption and environmental impact. Therefore, any technique that reduces milling waste, decreases water usage and shrinks impact during mine life must be considered a major innovation in mining.To these ends, one of the most impactful developments in mining within the last 10 years has been the expanded use of high technology sensors to create preconcentrations of mine ore (Jönsson, 2014). The most common sensors used are charge-coupled device (CCD) cameras, that allow through a red, green and blue (RGB) coloring system, the separation of minerals with different colors, tones and, in many cases, with differences in brightness.More recently, the development and use of dual energy X-ray transmission (DE-XRT) to enable the separation by atomic density of the constituent minerals within a given rock has become a reality. Within this work, a rapid bibliographical review of the CCD and DE-XRT methods and examples of their usage within mining and the industrial minerals sector are presented.Sensor-based sorting in miningAutomation within mining is one of the industry’s current goals. Sensors of various kinds have been used as steps toward automation in recent years, from improving the safety and productivity of haul trucks through the use of cameras and global positioning satellites (GPS), to the divination of slope failures. Just as with other mining areas, sorting has improved dramatically and made great steps toward automation in recent years (Wotruba et al., 2014).Sensor-based sorting (SBS) uses spectromatic sensors to identify intrinsic characteristics of particles and separates them by either mechanical or pneumatic means into different product streams (Wotruba et al., 2014). SBS can be used with great effectiveness to improve gravimetric beneficiation through the selective separation or preconcentration of run of mine ores (ROM)."

Jan 1, 2015

By I. M. R. Duarte, J. A. Rodrigues-Carvalho, F. R. S. Rosa, A. B. Pinho

"This paper aims to contribute to the knowledge of the mechanical properties of the shales and greywackes which constitute the flysch-type deposits of the Baixo Alentejo Flysch Group, in the south of Portugal. These formations are flysch-type deposits constituted by sequences of usually thick greywacke beds alternating with thin shale beds, which include sometimes intercalations of conglomerate beds. All the sedimentation of these flysch formations was controlled by tectonics. At the same time, should have occurred along with the first Hercynian deformation phase, a low-grade metamorphic event (chlorite zone), that affected these flysch deposits. This study highlights the influence of anisotropy and heterogeneity of these flysch rocks on their physical and mechanical characteristics. The anisotropy verified in some physical properties and on mechanical properties, due to the foliation makes difficult the sample preparation for the laboratory tests. Besides, it induces a scattering of the properties values measured, as for example, the strength and the deformability. The heterogeneity is related to the main features of these geological formations, which are constituted mostly by thinly stratified greywackes and shale beds, which sometimes may affect the results of the laboratory tests making them less representative. The study is made by using both shales and greywackes that constitute these flysch-type deposits in order to evaluate their geotechnical properties, mainly of the shales. Samples of these two rock materials, are tested accordingly a laboratory testing programme, which includes which included mineralogical analysis (X-ray diffraction), physical tests (bulk density, porosity, and void index) and mechanical tests (uniaxial compression, and deformability tests). INTRODUCTIONOne of the factors that most influence the geomechanical behavior of rocks, as well as rock masses is the anisotropy. The word anisotropy comes from two Greek words ""anisos"" (meaning uneven) and ""tropos"" (meaning direction). A body or material is considered to be anisotropic, where the same property has different values depending in which direction it is measured, therefore, an anisotropic material is one whose magnitude of the properties depends on the direction in which these are studied or measured. Otherwise, it is about an isotropic material. However, the fully isotropic materials are quite rare in nature."

Jan 1, 2015

By A. V. Lyamin, J. P. Wang, A. J. Li, Z. Qian

"For general stability analysis of rock slopes, rock mass strength and rock mass disturbance are definitely should be considered. In addition, the impact of earthquakes must be taken into account. In fact, the rock mass strength is very difficult to be assessed which causes the difficulty of analysing rock slope stability. Therefore, an empirical failure criterion, the Hoek-Brown failure criterion, has been proposed. It is one of the most widely accepted approaches to estimate rock mass strength. The rock mass disturbance is important and was found having significant influence on evaluating rock slope stability, especially for rock slope with poor quality rock mass. In the Hoek-Brown failure criterion, the disturbance factor can represent the level of the rock mass disturbance which would provide a reasonable basis for estimating rock mass strength.This research will not only discuss the slope factor of safety, but also consider the influence of the seismic force on rock slope stability assessment using pseudo-static method. In practice, only horizontal seismic coefficient is used. Various magnitudes of the disturbance factor and recommended blasting damage zone thickness are also taken into account. The blasting damage zone thickness considered ranges from 0.5 to 2.5 times of slope height. The research results have potential to be extended and then sets of comprehensive stability charts can be provided for the rock slope stability evaluations. They will be convenient tools for practising engineers. In this study, finite element upper bound and lower bound limit analysis methods are employed. Their applicability has been investigated in some previous studies. The differences between upper bound and lower bound solutions are less than ±10% which would provide reasonable and acceptable range for rock slope stability safety factor estimation."

Jan 1, 2015

By G. J. de Korte

South Africa’s best-quality coal, located in the central Highveld basin, is becoming depleted and alternative sources of coal, such as the Waterberg coalfield, will have to be developed to supply the country with coal in the future. The quality of the coal being mined in the central basin is gradually becoming poorer. This necessitates that more of the coal be processed to improve the quality to meet customer requirements. The challenge to the coal processing industry is to process low-yielding coals to produce goodquality products and at the same time ensure that coal mining remains economically viable. This requires that more cost-effective coal processing technologies be investigated and implemented.

Jan 1, 2015

By Mark McComb, Geoffrey R. Lane

"Over the years many differing approaches have been developed to clearly understand the nature, mode of occurrence, associations and deportment of both free-milling and refractory gold in a wide variety of differing geologic environments and plant products. Many approaches can be taken to characterize the ore which may occur as complex fine grained gold, ultra-fine grained gold, coarse nuggetty gold, complex Asrich refractory gold and double-refractory gold. The approach taken in assessing small drill core composites from Novo Resources Beaton Creek Paleoplacer gold project located in the Pilbara region of Australia was complicated by the nature of the ore, the small amount of sample available from current exploration work, and the gold grade and the grain size distribution. In this case the scope of the study was limited by sample availability although significant amounts of valuable information was also gained. This gold characterization study included the following elements:??Size fraction assays??Ore microscopy??Preparation of heavy mineral concentrates from sized fractions (screening) of crushed or milled head using heavy liquids and Superpan table.??Systematic scans of the heavy mineral concentrate, middling, and tailing fractions using TIMA Automated Scanning Electron Microscopy integrated with an Energy Dispersive Spectrometry to provide semi-quantitative elemental analysis of the individual grains found in the sample.The unique methodology employed to detail the gold deportment was the combination of the Tescan Integrated Mineral Analyser (TIMA) and the Oxford INCA GSR software. This technique not only allowed us to document the deportment of gold but recognize other associated minerals, which included gersdorffite, chalcopyrite, uraninite, coffinite, brannerite and several Rare Earth-bearing minerals.INTRODUCTIONGold deportment studies are commonly carried out on preliminary gold exploration projects in order to determine the various limitations, which may effect processing of the potential ore. This is often because it may be expected that there may be a refractory component to the gold, which may limit physical separation techniques and suggest more costly hydrometallurgical techniques. Often when carrying out gold deportment studies the mineralogical methods may be limited to assuming that the gold will be fine and easily found using standard techniques of optical microscopy or Scanning Electron Microscopy. This may not always be the case as various geological environments may pose their own individual problems to determining the deportment of the gold grains."

Jan 1, 2015

By D. J. Englund, R. A. Davis

"A three-dimensional CFD model of a straight grate furnace for indurating iron-oxide pellets was developed for exploring conditions of furnace operation for fluid flow, heat transfer and reactions. The model includes reactions for natural gas combustion in the gas phase and calcination and magnetite oxidation as well as drying in the pellet bed. The performance of the model was investigated with a series of pellet production rates that included adjustments to the fuel rates to achieve proper induration temperatures in the pellet bed. The model may be used to discover opportunities for process improvement.IntroductionIron oxide pellets are a feedstock to blast furnaces for iron making. Pellets require physical strength characteristics needed to maintain their integrity during storage, handling, transportation and smelting. Pellets are produced from iron ore in a series of mineral processing operations that form wet green balls from slurries of iron-ore concentrate with binders, such as bentonite, and possibly fluxing-agents such as limestone and dolomite. The green balls are dried, fired at high temperature, and then cooled in an induration furnace to achieve the strength and chemical composition required for efficient reduction and slag separation in blast furnaces. Induration furnaces are generally straight grates or grate-kilncooler configurations. These furnaces operate with pellet beds passing through a series of temperature zones to control drying and chemical reactions in the bed.Process air passes through the zones in an overall counter flow direction to the pellets for efficient heat transfer and energy recovery from the cooling stage. Consequently, the zone conditions and the overall furnace performance are highly coupled. Thus, it becomes challenging to predict how changes to any single zone may affect the rest of the furnace. To gain a better understanding of machine performance and coupling, a three-dimensional, steady-state model of a complete straight grate induration furnace was created using computational fluid dynamics (CFD)."

Jan 1, 2015

By Rakesh Kumar, Rajabrahma K., A. K. Verma, V. Mukesh

"In this study, laboratory investigation as well as numerical investigation is carried out to ascertain the transition from one mode to another for Semi-circular bend setup. Laboratory investigation is carried by varying the span length (s/2R); crack length (a/R); notch angle (a); and notch thickness (t). The specimen consists of cement, sand and water mixture in a ratio of 1:1:0.5 by weight and are prepared as per the ISRM standards (2014). Tests are conducted by a servo controlled universal testing machine at a strain rate of 0.2 mm/ min. The results are collected in terms of failure load, crack mouth opening displacement (CMOD) and images of crack initiation and propagation.Image analysis of laboratory tested samples shows that crack initiates at the notch tip when the notch inclination angle is 0°. As the notch angle increases (i.e. 30° and 60°) the fracture begins to initiate behind the notch tip. The direction of crack propagation in front and back side of the sample is same for notch inclination angle is 0° whereas it differs more and more as crack inclination increases. The transition represents the change in mode of failure from mode I (0°), mode II (30°) and mixed mode I/II fracture (60°).Finite element method used to find the transition based on MTS failure criterion. The inclination of notch is varied like 40, 42, 44, 45, and 50 deg and FEM analysis shows that the transition from mode-I to Mode-II take place at 49 deg. The same procedure can be extended to find the transition from mode-II to mode-III."

Jan 1, 2015

By D. A. Le, T. S. Nguyen

"In Canada and other countries, several types of rock formations are being considered for the geological disposal of radioactive wastes. In order to better understand the ability of these rocks to contain and isolate the wastes, the Canadian Nuclear Safety Commission collaborates with different international research organizations and has access to experimental data from Underground Research Laboratories (URLs) in the world. Such an URL is situated in Opalinus Clay, at Mont Terri, Switzerland. An experiment, consisting of the excavation of a tunnel followed by water and gas injections in a test section of the tunnel, was performed at the URL. The authors have developed a mathematical model, based on the poromechanics theoretical framework, to simulate those phases of the experiment. The constitutive relationship for the stress-strain behaviour of Opalinus Clay takes into account its inherent anisotropy due to bedding. The model was able to capture the main features of the experiment such as the prediction of the shape and extent of the excavation damage zone and its influence on water and gas migration.INTRODUCTIONIn Canada and many other countries, several types of rock formations such as crystalline rocks and sedimentary argillaceous rocks, are being studied for the disposal of used nuclear fuel from nuclear power plants. Geological disposal relies on multiple natural and engineered barriers for the long-term containment and isolation of the wastes. The host rock is a major natural barrier and is the subject of extensive research. The Canadian Nuclear Safety Commission (CNSC), Canada’s nuclear regulator, will be responsible for the licensing of future deep geological repositories. In order to evaluate the safety of deep geological repositories, CNSC staff keep abreast of scientific developments by collaborating with national and international partners on experimental and theoretical research on the long term performance of those engineered and natural barriers. Through that collaboration, the CNSC has access to data resulting from experiments performed at different Underground Research Laboratories (URLs)."

Jan 1, 2015

By J. Ita, F. Malekzadeh

"Multi-scale simulation in coupled fluid flow- geomechanical systems is a computationally efficient method for numerically solving large poroelastic systems. When using multi-scale methods, care must be taken in ensuring consistency when information is exchanged between systems that have a different discretization. Here a method is presented which provides consistency between the pore pressure being calculated on a fine scale fluid flow domain and upscaled to the coarser scale geomechanical domain and the pore volume change being calculated on the coarse geomechanical domain and down-scaled to the fine fluid flow domain. Central to this process is the characterization of the mechanical properties of the poroelastic system at both scales.Another advantage of the method presented here is that it is applicable to hydraulically disconnected but laterally drained (i.e. multi-porosity) layered systems as well as hydraulically connected, layered systems. Thus it can be used in geological situations where thin shale streaks or hardpans impede flow between laterally extensive, hydraulically conductive units. This is significant as the pressure evolution of such a hydraulically disconnected, laterally drained system can be very different than a hydraulically connected one as shown here. INTRODUCTIONA multi-scale treatment of fluid flow and deformation is a key enabler when simulation of poroelastic phenomena is limited by computational resources. As the spatial domain of the geomechanics model is usually larger than the fluid flow model, it is desireable to use a coarser discretization in the geomechanical model compared to the fluid-flow model. This type of multi-scale simulation requires a consistent up-scaling of pore pressure from the fine scale fluid flow model to the coarse scale geomechanical model and down-scaling of pore volume change from the geomechanical model to the fluid flow model (see Figure 1)."

Jan 1, 2015

Block caving is an underground mining method for the profitable extraction of massive, low-grade orebodies. Lately, it has become the mining method of choice, for many mining companies, because of depleted high-grade orebodies, and declining metal market prices. Block cave mining, however, still faces several challenges. Lack of access to the cave remains a major issue in understanding the rockmass response to mining for method optimisation. Improving our understanding of the rockmass response to caving will lead to safer and more productive operations. Combining large datasets from multiple sources with virtual reality scientific visualisation (VRSV) is a viable alternative to understanding complex cave behaviour without access to the cave. This is achieved using immersive environments with the ability to view complex multi-dimensional data (beyond 3D) graphically. VRSV offers a unique platform where it becomes possible to immerse the multi-disciplinary experts, and/or management team, in a virtual mine environment for quick decision making and fast resolution to conflicting conclusions. The underground mining system is complex due to multiple interrelating factors such as geology, excavation geometries, stress and time. Block caving is even more complex than most underground mining methods due to the network of tunnels required, and the use of induced stress, among others. As a consequence of the complexity in the block caving environment, it is vital that the mining system is analysed holistically, as a system, rather than optimizing individual factors one at a time. This paper presents a customised software module developed for use in the Advanced Visualisation Interactive Environment (AVIE) at The University of New South Wales (UNSW), Australia, to enable VRSV investigation into block cave mining systems (BCMS). This approach has the potential to provide a better understanding of the effect of time in in rock engineering, which has proven to be an important factor in hard rock mines (Ma & Daemen, 2006; Malan et al., 1997; Suorineni, 2010) but never validated. This work back analyses the early undercutting phase of a case study block caving operation with the view to understanding time/sequence effects. There is evidence that heterogeneous rockmass time-dependent behaviour governs the seismic response of the rockmass following undercut developments.

Jan 1, 2015

By L. Janku, G. Hancox, M. Villenueve, C. Massey

Wellington lies in a seismically active area 150 km from a subduction zone and in the vicinity of several active faults, which poses a risk to its infrastructure and inhabitants. One of these major faults, the Wellington Fault, runs through the centre of the city and across several lifelines, including the natural gas pipeline and the freshwater pipeline. The first settlement in the area was severely damaged in 1848, soon after its establishment, by an earthquake of approximate magnitude Mw 7.4 - 7.5 (Grapes, Little, & Downes, 1998). In 1855, another earthquake of magnitude Mw 8.2 generated by a nearby fault uplifted the eastern part of the current Wellington area and caused several landslides in the surrounding hills (Grapes & Downes, 1997). The Central Business District lies in the area of a sedimentary basin and partly on reclaimed land. Many residential areas, as well as some vital infrastructure, however, lie on or along the slopes in the surrounding hills. The bedrock in the area comprises predominantly the Torlesse greywacke of Permian – Late Triassic age. The greywacke is tilted to a steep angle, intensively faulted and fractured (Cook, 2001). Even though several studies in the past assessed the seismic risk in the area (e.g. Brabhaharan, Hancox, Perrin, & Dellow, 1994), the studies either focussed solely on the area of the sedimentary basin or based their assessment of the hilly terrain purely on slope morphology (slope angle). Previous studies have shown that slope shape and contrasting materials in the slope can amplify earthquake ground motions, such factors are typically called site effects (e.g. Geli, Bard, & Jullien, 1988). Any attempt to systematically quantify the site effects and consequent seismic response of the slopes and use it to predict the consequences of the next large-magnitude earthquake, has not yet been carried out. In this extended abstract we outline the methodology of a PhD research project, focussed on investigating the site effects on the slopes around Wellington and on creating representative numerical models of ‘characteristic’ Wellington slopes and materials. This extended abstract presents the methodology adopted for the assessment using the Te Ahumairangi Hill site as an example.

Jan 1, 2015

By M. Laliberte

"Gold-mine effluents are often characterized by high concentrations of copper, ammonia and cyanide derivatives (mostly cyanates and thiocyanates). While not acutely toxic to birds, this water can be acutely toxic to fishes and invertebrates. In many jurisdictions, the effluent requires further treatment in order to pass a mandatory requirement to be nonlethal to species like the rainbow trout (Oncorhynchus mykiss) or Daphnia magna. Using actual mine water, it has been demonstrated that aerated moving bed biofilm reactors will biodegrade the ammonia, cyanides, cyanates and thiocyanates, thereby removing the toxicity associated with these components. By removing copper by precipitation the water can be made to pass acute toxicity tests. Tests have demonstrated that the process is stable between 4 and 25°C, with no significant changes in the treated water composition. Once the biomass is acclimatized, the process is resistant to upsets and requires very little inputs except for phosphorus and air. Furthermore, it has been demonstrated that an anoxic reactor can be added downstream of the aerated reactors to remove nitrates if required.IntroductionThis paper will demonstrate that gold-mine effluents, which are toxic to fishes and invertebrates, can be made nontoxic by using a combination of chemical precipitation and biological oxidation.The typical composition of gold-mine effluents will first be described. The applicable legislation will then be introduced, with its requirement that the treated effluent be nontoxic. The toxicity of a typical untreated effluent will then be confirmed, and the sources of the toxicity identified. After that, a number of toxicity reduction treatment methods will be presented, and the selected method will be described.The lab tests that confirmed the efficiency of the treatment method will be presented, with three phases of testing as the understanding of the process gradually improved. Toxicity test results showing that the water is nontoxic after treatment through the temperature range will be presented."

Jan 1, 2015

By Leibniz University, D. Zapf

"The demand for gas storage operations with high withdrawal rates and operation modes different to a seasonal storage regime requires a more detailed rock mechanical consideration of thermal induced stresses in the vicinity of the caverns. This means that the change of gas temperatures during operation and the consequences of these temperature changes on the stressing of the salt rock mass must be taken into account in the rock mechanical dimensioning. Within the rock mechanical calculations a loading history, i.e. a pressure versus time dependency, has to be defined. As rock salt has a time dependent material behavior stress redistributions in the rock salt mass take place even under constant internal pressure conditions. Therefore not only withdrawal and filling periods but also the duration of phases with nearly constant internal pressure is significant for the resulting state variables. Within the paper the differences and consequences for the rock mechanical recommendations are discussed. As a result it can be concluded that recommendations with respect to minimum operation pressure as well as for maximum withdrawal rates can be answered only in connection with the respective time intervals."

Jan 1, 2015

By C. Pomeroy, J. Weyer, J. Brune

"Mining began in the Erzgebirge (“ore mountains”) region of Saxony, Germany more than 800 years ago, and extensive underground workings cut through the entire area. Some of these old workings are still used today: not for production, but for offering an underground venue for research, tourism and university teaching. One example is the Reiche Zeche mine at the Technische Universität Bergakadamie Freiberg which hosts one of the oldest mining engineering programs in the world. It is imperative to keep all active mine workings well ventilated to make the mine safe for students, visitors and researchers. Since the mine workings at Reiche Zeche are so vast, extensive and, to a large extent unexplored and unmapped, it has been difficult to provide a complete, functioning and adequate mine ventilation model for this mine that accounts for all known and unknown leakage air flows. Researchers at the Colorado School of Mines have cooperation with their colleagues at Freiberg to establish a mine ventilation network model based on a limited number of air readings in known and accessible drifts. In order to balance the measured air quantities, leakage flows were quantified and mapped by comparing input and output flows of mapped drifts, and modelled using Ventsim Visual, a powerful visualization software package. The resulting mine ventilation model is used to locate and quantify the leakage air flows and to examine how much air is lost in each area. With this model, ventilation changes and improvements underground can be documented reflected in the model. This enables the Bergakadamie Freiberg to project air changes required for scientific experiments and to set up mine ventilation in specific areas and for specific needs. The model also enables better ventilation control and monitoring than before. Finally, the model can be used to predict ventilation changes and escape way contamination in case of a fire, ground fall or inundation in the mine. The latter becomes important as the lower mine workings are often flooded during spring runoff, which has created uncertainty about mine ventilation in the past. HISTORICAL BACKGROUND The discovery of silver, lead, zinc, tin and other valuable metal ores in the Erzgebirge region of Saxony, Germany began in the12th century and started a mining boom than lasted for centuries. Surface mines quickly developed underground to access the higher grade veins. Explored by the early geologists and driven by the ingenuity of the miners, the underground works expanded vastly throughout Freiberg and the surrounding region. Development followed the highest grade veins, and engineers developed solutions to drain water and provide limited ventilation to the underground workings. Still, engineered and planned ventilation was usually not a priority in the development of a new drift, which today makes ventilation modeling a significant challenge."

Jan 1, 2015

By H. -S. Yoon, C. -J. Kim, K. W. Chung

"With the final goal of ultrasonic application to ion exchange in a resin-in-pulp (RIP) system, the feasibility of an indirect ultrasonic application with a submersed ultrasonic probe was investigated first for the enhancement of ion exchange in the following resin-in-solution (RIS) system: Lewatit MonoPlus MP 600XL in an artificial solution with 106 ppm uranium. Ultrasonic radiation enhanced the ion exchange efficiency without mechanical degradation of resin. For 3.6 g/L of resin, the enhancement was 79 percent after 10 min of ion exchange and it gradually decreased to 11 percent at 60 min. In addition, a preliminary test of the mechanical stability of the resin in the RIP system showed little mechanical fracture of the resin due to ultrasound, which indicates that indirect ultrasonic application by a submersed ultrasonic probe is applicable for RIP systems. IntroductionIn uranium ore processing, the ion exchange process has been used on a commercial scale for preconcentration and purification (Gonzalez-Luque and Streat, 1984). The ion exchange process is divided into two processes: (1) a resin-in-column process with the uranium-bearing solutions passed through columns containing resins and (2) a resin-in-pulp (RIP) process with the leached ore pulp exposed to resins. The latter does not require the separation process of leach liquor and ore solids, which reduces process costs. This process, which has been developed commercially since 1955, has a certain drawback. The adsorption rate and efficiency in the RIP process are relatively low, so numerous contacts between resins and leached ore pulp are needed, which adds to the cost (Merritt, 1971). It is necessary to study methods to reduce process costs.Ultrasound can intensify mass transfer, increase the rate of chemical reactions, and change reaction pathways (Thompson and Doraiswamy, 1999; Luque de Castro and Priego-Capotem, 2007; Adewuyi, 2001; Luque-Garcia and Luque de Castro, 2003). It has great potential in chemistry and is especially considered to be a promising method for enhancing mass-transfer-limited processes, such as ion exchange. Enterzari and Tahmasbi (2009) reported the effect of ultrasound on water softening by ion exchange. Band et al. (1997) proposed a modulated ultrasound application to water desalination with ion-exchange hollow fibers. These reports revealed that ion exchange kinetics could be enhanced by the application of ultrasound. As for hydrometallurgy, Feng and Aldrich (2000) reported that the elution of an ion exchange resin was enhanced by the use of ultrasonication."

Jan 1, 2015

By Mengsu Hu, Yuan Wang, Jonny Rutqvist

Material interfaces and typical boundary conditions are boundaries influencing the existence, uniqueness and stability of numerical solutions of water flow in heterogeneous media. The Numerical Manifold Method (NMM) with a two-cover-meshing system is an ideal method to handle boundaries, considering its flexibility with no need to adjust mathematical nodes onto boundaries, the meshing efficiency, and its integration precision. In this study, we derive and compare two new approaches for boundary constraints, i.e., a discontinuous approach with Lagrange multiplier and a continuous approach with jump function in the frame of NMM. In the discontinuous Lagrange multiplier method (LMM), Dirichlet boundaries or the material interfaces are regarded as discontinuities which are linked by Lagrange multipliers. In the continuous Jump function method (JFM), the material interfaces are regarded as inner interfaces, where the refraction law is realized by constructing jump terms with discontinuity of hydraulic gradient in its normal direction. Both the continuous and discontinuous approaches make full use of the aforementioned advantages of NMM and are established based on a clear physical meaning of water flow by our energy-work seepage model. The newly derived boundary-constraint approaches were coded into an NMM water flow model and tested for precision and efficiency on different simulation examples. We first tested both LMM and JFM for an idealized heterogeneous model, comparing the numerical results with analytical solutions. Then we tested both approaches with a heterogeneous model and compared the results of hydraulic head and specific discharge. We proved that both approaches are very suitable for material boundaries considering the accurate realization of the boundary constraints and the flexibility with no need for mesh-conforming.

Jan 1, 2015

By C. O’Hara, S. Roy, K. Swedburg, J. Katchen

"New Gold Inc.’s New Afton concentrator commenced operation in June 2012, producing a copper-gold-silver concentrate. During the first two years of operation, various optimization efforts have improved mill throughput, recoveries and concentrate grade. Daily mill throughput has increased 20% above the design rate. This was achieved through more consistent instantaneous feed rate and size distribution from the mine reclaim stockpile, higher pebble crusher reliability, changes to the SAG and ball mill grinding media sizes, larger SAG grate openings, reduced SAG discharge screen-deck aperture size and an increase in the maximum ball mill power draw limit. Metal recoveries at New Afton are primarily limited by liberation in the coarser size fractions; therefore, improving the grind size at a given mill throughput has been the main means of improving recovery. The average rougher flotation feed F80 size was reduced from 175µm in Q1 2013 to 165µm in Q1 2014, while the average operating mill throughput increased by 25%. Other flotation circuit changes focusing on recovery improvement include the addition of froth crowders to the rougher cells and the use of a stronger frother. The average concentrate grade increased from 22% Cu in Q1 2013 to 25% Cu in Q1 2014. This was achieved by redirecting the flash flotation concentrate stream to the regrind circuit and by the addition of lime to the cleaner circuit.This paper describes the above improvements made at the New Afton mill. The paper describes the objectives, timing and end result of each area of improvement.IntroductionThe New Afton Mine is situated approximately 10km west of Kamloops, British Columbia, 340km north-east of Vancouver. The mine has a moderate climate, access to transportation and electrical infrastructure, nearby fresh water supply, and close proximity to industrial and mining service businesses. The population of Kamloops is around 90,000 with most mine employees living in or around the city."

Jan 1, 2015

By S. Sakurai

"Gravitational force is an external body force acting on underground structures. It should be noted that gravitational force cannot be replaced with the surface traction vector (Cauchy stress) which is an internal force. This fact should be properly taken into account in a numerical analysis of underground structures, particularly for structures such as vertical shafts, tunnels, and caverns constructed at great depths. It is obvious that the gravitational force must be conserved at all times.In conventional numerical analyses, the initial state of stress of the ground medium is firstly calculated under the gravitational field. This means that the gravitational force is replaced with stress (surface traction vector), and after that only the initial stress is considered in the calculation of the stresses and displacements of the structure. It should be noted that the initial stress is Cauchy stress consisting of a surface traction vector, while the gravitational force is a body force acting on the mass of the materials. This computational approach may be acceptable for elastic problems because the principle of superposition is valid for elastic materials. However, this approach becomes questionable for elasto-plastic materials because there is no guarantee that the principle of superposition is valid for them.Furthermore, another problem exists in elasto-plastic analyses: The stress state in a plastic zone must satisfy a yielding criterion such as that of Mohr-Coulomb. In order to make the stress state satisfy the criterion, an excess stress beyond the yielding criterion should be transferred to an elastic zone existing outside of the plastic zone. This seems to always be possible, because an elastic zone always exists, no matter how large of a plastic zone appears. In some cases, however, the excess stress cannot be transferred to the elastic zone because the gravitational force must be conserved. Therefore, it is obvious that the magnitude of stress around underground structures may become large and surpass the yielding criterion at great depths where a large gravitational force exists.In this paper, it is demonstrated that in a conventional elasto-plastic numerical analysis of a vertical shaft at a great depth, all the stress components around the shaft become very small, even though a large gravitational force exists. This strange result may be due to the fact that the gravitational force is not properly taken into consideration in the numerical analysis."

Jan 1, 2015

By D. Pawelus, J. Butra, R. Debkowski, M. Szpak

Impact of horizontal stresses on stability of underground workings in mines is a very important issue in underground mining. Identification of the initial state of stress in the rock-mass should be one of the main actions taken into account while designing and carrying out the mining activity in underground mines. The paper presents the tests on three dimensional stress pattern in Polish copper mines, owned by KGHM Polska Miedz S.A. Group, carried out in 2012. The research program covered 7 measuring stands in two mines; their average depth was about 1000 m. The main aim was to identify the values and directions of horizontal stresses in order to optimize the extraction and to improve the safety. The overcoring method with the use of CSIRO HI type probe was applied. The paper also describes the measuring technique which was developed for the purpose of specific mining and geological conditions of KGHM mines, taking into consideration the natural hazards encountered there as well as technical and operational capabilities with regard to drilling equipment. The experience gained during the underground measurements and the issue of making such measurements in underground copper mines in Poland are presented in the paper. The stress patterns obtained during the underground measurements are of application importance for the process of designing the spacing of mine workings and improving their stability and mine support selection.

Jan 1, 2015