Search Documents

By Jinqian Zhao, Jiarong Li, Shizhong Liu

"Creep cavitation of in single crystal (SX) superalloy was investigated. The constant load creep tests, in single crystal superalloys DD6, were conducted at the conditions of 800°C/700MPa, 850°C/550MPa and 900°C/450MPa, respectively. It was found that there were square facets on the stress fracture surface, and microscopic cavities in the ruptured specimens in the vicinity of the fracture surface. Both the square facets on the fracture surface and microscopic cavities in the section of the ruptured specimens show the morphology of the same thing at the different views, namely creep cavities, which are take the form of flatten cuboid. In fact, creep cavities are the longitudinally tensiled creep cracks slowly growing during the stress tensiling. The factors of creep cracks nucleation and growth conditions include: (a) enough high temperature to activate diffusion (b) casting pores as nucleation origination (c) high strains and strain rates. Eventually, the instantaneous fracture mechanism of creep specimen is cleavage fracture.IntroductionFor the materials used in elevated temperature service, creep behavior has to be accounted for. It is well recognized that creep rupture in polycrystalline materials at high temperature occurs principally by the nucleation and growth of microscopic cavities at grain boundaries, followed by microscopic cavities linkage to form micro- and eventually macro-intergranular cracks[l,2]. Without the usual grain boundaries, SX superalloys have superior capabilities at high temperatures to polycrystalline superalloys, and have become an established feature of gas turbine technology where they are commonly employed in the manufacture of high performance blades[3]. A considerable amount of work has been done over the past tens of years, and many models for nucleation and growth of creep cavities have been proposed, however, those are mainly for polycrystalline materials.In order to improve creep resistance that single crystal superalloys, in which grain boundaries are removed, have been developed. Because there don't exist grain boundaries in SX superalloy, the mechanism of nucleation and growth of creep cavities must be different from that in polycrystalline materials.Understanding the formation and characteristics of creep cavitation is crucial to model the lives of single crystal superalloys.M. Marchionni and L.G. Zhao et al. found that there were square facets on the stress fracture surface [4,5]. Roger C. Reed pointed out creep cavities lie in the necked region[6]. In this paper, the effects on the formation of creep cavities are discussed, as well as the morphology of creep cavities and fracture mechanism of SX superalloys."

Jan 1, 2013

By Takashi Sasaoka

A great deal of coal will be left under the final end-walls in Chinese surface coal mines because of lower slope angle in shoveltruck mining systems and larger mining depths. In traditional surface mining systems, the coal under the end-walls will be buried by the inner dumping site, and these coal resources are generally abandoned. Considering these situations, the application of end-wall mining systems was considered in order to recover the residual coal around the end-wall. This mining system can improve economic benefits by exploiting haulage and ventilation roadways from end-walls and utilizing the existing transportation systems. In order to develop the appropriate pillar design methodology for the end-wall mining system, several empirical formulas and methods were discussed based on the formulas developed so far and the mechanics properties of coal and rocks in the Chinese coal mine. From the results of a series of theoretical and numerical analyses, it can be concluded that the coal pillar width calculated by the Mark- Bieniawski formula may serve as an important reference for pillar design in end-wall mining systems, and the end-wall mining system can increase the coal recovery from residual coal resources around highwall and reduce the effect of underground mining operation on slope stability

Jan 1, 2013

By K. Lascelles

ABSTRACT Nickel compounds vary significantly in their toxicological properties, so it is critical that continuing studies to accurately quantify worker exposures consider the processing that accompanies refining nickel-containing materials. The Clydach nickel refinery, which has operated for more than 100 years, was the first nickel-producing facility to show a high risk for lung and nasal-sinus cancers among workers employed since it opened in 1902. Process chemistry and equipment have changed dramatically over Clydach’s history. This paper describes the processing evolution at Clydach with a focus on the propensity for aerosol formation and the forms of nickel in airborne dusts.

Jan 1, 2013

By Zach G. Agioutantis

The prediction of ground movements due to underground mining using the influence function method is a mature technology, widely used by researchers and planning engineers around the world. Surface strain, either tensile or compressive, is an important indicator of potential impacts on structures such as buildings, bodies of water, pipelines, railway and power lines, and tailings dams. Calculation of static or dynamic surface strains, for varying surface terrains and slopes, should be accurately predicted and be independent of the methodology applied for the calculation. This paper discusses and compares the development of horizontal and ground strains on the surface due to underground mining for different surface topologies (sloping terrain, monitoring lines, etc.) and presents the steps needed to ensure accurate calculations. Examples are given to demonstrate how ground strains can be calculated for one- and two-dimensional gridded surfaces.

Jan 1, 2013

By Andrea Francioso, Roberto Folchi

In order to comply with the latest European Highway Standards, the highway Salerno - Reggio Calabria, in southern Italy, had do be widened and upgraded to reduce its vulnerability to earthquakes. Reinforced concrete viaducts, no longer needed for the new road, had to be demolished. Many bridges still to be used for the highway required refurbishment due to 50 years of wind, frost and salt corrosion. This re-furbishment and new construction had to be carried out simultaneously. To keep the highway open dur-ing the renewal process, all traffic was directed to one side of the road. Demolition was conducted ex-tremely close to operational roadways and viaducts, as close as only 2 cm (0.8 in). Care had to be taken to ensure that the stresses (vibration levels), resulting from the demolished pylons and decks hitting the ground, were below the no-damage thresholds for the nearby acceptors (structures receiving the vibra-tion stresses). These structures included bridges, houses and buried pipelines (water, oil and gas). In some cases, care also had to be taken to preserve the existing pylons supporting decks that were being demolished; since the same pylons were going to be used for the new viaducts (bridges). New continu-ous decks in weathering steel replaced the old reinforced concrete decks.

Jan 1, 2013

By Marco Lombard, Paulus Kapolo, Christopher J. Greet

"The conversion of a concentrator from one grinding media type to another is a major undertaking in terms of both financial and technical risk. So, a strategy of completing sufficient laboratory and field tests to mitigate this risk, and give the operation confidence that advancing to plant trial will give a high probability for success.The objectives of this paper are twofold: to provide the reader with a strategy for mitigating risk prior to undertaking a plant trial; and to provide a statistical basis for analysing plant trial data. That is, when employing an electrochemically inert grinding media in the primary grinding circuit it is possible to change the pulp chemistry of the system and improve the metallurgical response of the ore.This paper tracks the changes in pulp chemistry and metallurgical performance of Rosh Pinah Zinc Corporation’s silver/lead/zinc concentrator as the primary ball mill was converted from forged steel grinding media to high chrome grinding media. The changed in metallurgical performance are correlated to the shift in pulp chemistry.INTRODUCTIONTheoryBruckard et al (2011) recently published an article describe the effect of the grinding environment on the flotation of copper sulphides. While this paper confined its discussion to copper sulphides the arguments presented apply equally to other sulphide mineral systems. Broadly, these studies indicate that most sulphide minerals are more noble than the grinding media used during comminution. Therefore, the sulphide minerals are cathodic with respect to the forged steel grinding media, and the following reactions apply:Cathode (sulphide mineral): ½O2 + H2O + 2e- ? 2OH- (1)Anode (grinding media): Fe ? Fe2+ + 2e- (2)A galvanic couple between the grinding media and the sulphide mineral(s) exists, which increases the corrosion rate of the forged steel media. The corrosion products of the grinding media, iron oxy-hydroxide species, invariably precipitate on to the surfaces of the sulphide minerals thereby affecting their floatability (Johnson, 2002).The application of more electrochemically inert grinding media to “real” ore systems at an industrial level to improve metallurgical performance has not gained universal acceptance. The aim of this paper is to provide a protocol for conducting laboratory and plant test work that clearly demonstrate that metallurgical benefits are not only possible, but measureable, by way of example. In this case, the work conducted at Rosh Pinah Zinc Corporation in Namibia is described."

Jan 1, 2013

By L. Shoke

The aim of this study was to develop an in-house tensile testing procedure that would yield accurate and reproducible parameters as input material properties into computational models for numerical simulations of the mechanical behaviour of TM380 mild steel. To achieve this objective, we reviewed the ISO 6892:2009 tensile testing standard along with reported good practice guidelines. Tensile tests were conducted on a dog-bone shaped TM380 mild steel specimen with strain gauges attached on either side, to monitor alignment and measure strain, using three different types of tensile testing machines. Parameters quantified included yield stress, ultimate tensile strength, and modulus of elasticity. The values of these parameters were found to be in agreement with the values supplied by the manufacturer's specification and showed minimal variations between laboratories. Thus it can be concluded that the tensile test procedure used resulted in accurate and reproducible results. The strain values calculated as per standard were in disagreement with those determined from extensometer and strain gauges and resulted in lower elastic modulus values. This confirms that the current testing procedures require the use of long-range strain gauges or extensometer to determine the strain. A chemical analysis was conducted to verify the specification by the manufacturer. The specimen was found to be fairly homogeneous with minor sulphide inclusions. The micrographs reveal a pearlite and ferrite structure typical of mild steel, and the fractographs show a dimpled surface typical of ductile fracture, which is an attribute of mild steel.

Jan 1, 2013

By Frank Schmidt

Due to changing geology, rib bolting is an ever-changing problem in ground control. With the economic status of the coal market, the need for safely increasing productivity in rib bolting is at an all-time high. The current solutions used in the market often require a long installation time (e.g. if collapsed holes have to be redrilled) or result in poor quality installations that can lead to insufficient ground control. A new bolting product based on the simple screw principle has been developed to bolt ribs faster and with a more repeatable, higher level of installation quality. The paper covers the product invention and development, the fastening principle and its advantages over current systems and first experiences in the market. The first underground trials have shown that the screw anchors can be installed safely and efficiently, often faster than traditional methods. The screw anchor does not suffer from conventional bolting issues such as collapsed holes due to bad ribs. The screw anchors are designed to obtain steel failure and load testing underground shows consistent fastening in all types of conditions.

Jan 1, 2013

By M. Solomon

During the course of 2011 the nationalization of mines emerged as one of the most contentious and emotive political issues under review. Some four years after the African National Congress electoral conference held in Polokwane, which had led to a change of leadership within the country's ruling party, elements within the ruling party's youth league, which had been virulently supportive of the change in leadership, turned on the incumbent President, using the mining question as its rallying call. At issue was the expressed perception that mining has, since the country's democratization, not delivered the anticipated benefits to the population as a whole, continues to be the preserve of the capitalist element of the South African community, and is therefore in need of radical reform. Aspersions were made that transformation within the industry had failed dismally and that mining companies had not delivered against their commitments to the Mining Charter and social and labour plans. The debate became extremely vocal and heated, evoked dramatic and emotive opinions, and vigorous skirmishes on the matter were fought in the media over much of 2011 and into 2012.

Jan 1, 2013

By Marisa Di Sabatino, Michael Phan Knudson, Mari Juel, Eivind Øvrelid

"A p-type Czochralski silicon ingot doped with boron was characterized for resistivity, minority carrier lifetime, interstitial oxygen, and metallic impurities. Analyses show a peak in resistivity and a dip in lifetime both occur 5 cm from the top of the ingot crown. This peak in resistivity deviates from the expected trend based on Scheil's equation for boron distribution. High concentration of interstitial oxygen in this area suggests that other oxygen-related defects, such as thermal donors and precipitates, may also be present here, and the observed peak in resistivity and dip in lifetime could be attributed to such defects. The low lifetime of 15-30 µs at minority carrier density of 7.5 x 1014 cm-3 is likely due to copper contamination.IntroductionSolar energy resources vastly exceed all other alternative energy resources, ensuring that solar power must play a crucial role in the evolving energy market. The economic viability of solar power in competition with other energy resources depends upon finding efficient, cost-effective, reliable, and controlled methods for solar cell production. In this regard, minimizing waste (such as material with unsuitable electrical properties that hinder solar cell performance) is a vital component of making solar cell manufacturing cost-effective. Impurities affect electrical properties of solar cell silicon in different ways (i.e. [1, 2, 3, 4, 5, 6]). In this work we focus on the role of oxygen and metallic impurities. Understanding oxygen impurities in silicon is critical to solar cell development because oxygen has been attributed with influencing critical electrical properties including resistivity and minority carrier lifetime and thereby potentially hindering solar cell performance or rendering material unsuitable for solar cells.[1, 2] Furthermore, oxygen is a common impurity in the standard type of solar cell silicon, Czochralski (CZ) silicon, due to diffusion of oxygen from the silica crucible into the melt during crystallization. [7] This study investigates the effects oxygen impurities have on the electrical properties of p-type CZ silicon."

Jan 1, 2013

By Shadia J. Ikhmayies

"Nanocrystalline fluorine doped tin oxide (Sn02:F) thin films were produced by the spray pyrolysis technique (SP) on glass substrates at a substrate temperature T, = 450 ° C. The hydrated stannous chloride (SnClz.2H20) was used as a precursor and ammonium fluoride (NH4F) and hydrofluoric acid (HF) were used as the doping compounds. A comparison between the compositional, morphological and optical properties of the films obtained by using the two doping compounds was performed by using scanning electron microscope (SEM) observations, energy dispersive spectroscopy by X-rays (EDAX) and transmittance measurements. It is found that the films prepared by using HF have larger grain size, and higher fluorine content than the films prepared by using ~- In addition these films have higher transmittance and higher direct optical bandgap energy. These results are interesting for the use of Sn02:F as a forecontact in CdS/CdTe solar cells.IntroductionTin dioxide is an n-type, wide bandgap semiconductor (about 3.5 eV) and in the form of thin films, it is a transparent conducting material, characterized by high optical transmission (80- 90%) [l]. Sn02:F is the most widely used transparent-conducting oxide material. The transparent-conducting thin films of this oxide are used as electrodes in a variety of optoelectronic devices, as heat mirror coatings in 'smart windows' for buildings, in automobile and airplane windshields, in incandescent light bulbs, in flat-plate and concentrating solar collectors. Tin oxide and zinc oxide, in thin film configuration are technologically important materials because of their applications in photovoltaic cells [2].Among various dopants for Sn02, fluorine is often preferred, because fluorine doping results in films with high transparency and good conductivity [3]. By exploring the literatures, it was found that different sources of fluorine were used to produce Sn02:F thin fihns, among which are ammonium fluoride (NH4F) and hydrofluoric acid (HF) are the most used. Some researchers used~ [2, 4-7] and others used HF [3, 6-8] for doping Sn02 films. Gordillo et al.[7] used both of NH4F and HF and showed that the resistivity of thin films obtained by using HF was lower than that of similar films obtained by using NH4F by a factor of 2.2. They also found that the films obtained by using HF have more random orientations."

Jan 1, 2013

By Walter Voglauer

On May 14, 2011 a chimney blast took place in Vienna, Austria. The blasting operation was part of the demolition works at a former railway fabrication. The demolition works on this ground were done under the leadership of the Austrian construction and demolition company PORR. In agreement with the civil organizations which were involved, the commander of the Regional Military Command of Vienna, Brigadier general Dr. Karl SCHMIDSEDER ordered a reserve force engineer company to demolish the chimney. The concrete planning of the chimney blasting was done by specialist Markus SEWALD who belongs to the HEERESTRUPPENSCHULE (combined armed force school) of the Austrian armed forces.

Jan 1, 2013

By Robert Kozicki, Eric Graham, George Wrightson

"IntroductionThe manufacture of Ferro Chromium involves the smelting of various ores and fluxes to produce the metallic product.Slag is inherent in the process. It has a much lower density than the metallic FeCr. Some chrome may be trapped in the slag as either FeCr or Cr203.Previous methods to estimate the slag in the FeCr have revolved around separating the slag and metallic portions by exploiting the differences in density. The downside with that procedure is that material will often contain pieces that are adhered FeCr and slag. The Metallic FeCr may also be completely encapsulated in the slag.An alternative and more precise method involves calculating the slag content based on chemical analysis of Mg and Al. The Mg and Al will be at relatively low levels (less than 0.1 % ) in the Metallic FeCr pieces and considerably higher in the slag (3% or greater). The overall sample will have a proportional amount and is calculated using simultaneous equations with the assumption there is only one kind of slag and one kind ofFeCr present. ""Pure"" slag and ""pure"" FeCr are needed in order to determine the Mg and Al in each. The detemlination of the Mg and Al in the overall sample would then be used to calculate the amount of slag.When the particle size is small, it is difficult to sample and get ""pure"" pieces of the slag and FeCr of sufficient quantity to perform a proper analysis. Often, historic data is used but that is dependent on the source of the FeCr and the materials used in its production. Mg and Al levels in slag can vary between 3% and 20% in different FeCr slags depending on their origin."

Jan 1, 2013

By Jose Antonio Silva Souza, Emanuel Negrao Macedo, Iara Ferreira Santos, Otacilio Dias, Luis C. A. Venancio

"The Bayer process alumina production generates 0.7 to 2.0 ton of bauxite residue (BR) and an average of 1.0 ton of C02 per ton of alumina produced. The direct reaction of exhaust gases to reduce the alkalinity of the BR may allow a triple gain: improve the storage conditions, open a range of new applications for BR and sequester from 16 to 102 kg of C02 per ton of alumina. This paper shows the measurement of C02 captured during a pilot scale reaction of a suspension of BR in water with flue gas, produced from direct oil burning. Three different types of reactors were used: one spray tower and two packed columns. The inlet and exhaust gases were analyzed using electrochemical and non dispersive infrared sensors. The pH of the suspension was monitored during and after the reaction to evaluate the buffer effect.IntroductionAlumina is mainly produced from refining bauxite using the Bayer process. This process consists of extracting the aluminum oxide through its dissolution in caustic soda and the separation of insoluble residues. The remaining bauxite residue (BR) although not particularly toxic, poses risks to the environment due to the large volume and its reactivity. According to the latest technology it is stacked on sealed deposits specially constructed. To date the vast majority of the bauxite residue that has been produced was stored and were not incorporated into any existing production processes to significant amount with exception to some extent of the sintering process residue at Russia and China [l]. On the other hand, a strategic goal was set in 2010 by the Bauxite and Alumina Committee of the International Aluminium Institute (formed by the majority of the industries) to reuse 20% of BR in 2025 [2]. China has established the same objective for 2015[1].This paper is a sequel of two others presented at TMS 2010/2012 [3-4] and describes:• A pilot plant assembled for testing the carbonation process of BR with gaseous effluents similar of the refining process.• The methodology used to measure the amount of C02 captured during the carbonation process.• The results of the carbonation process, the C02 capture and the buffering effect of the pH.This process is studied in order to consume minimal power and use the effluent as efficiently as possible in different reactors from low cost to ultra high performance. The process is designed for minimizing the power consumption and equipment investment."

Jan 1, 2013

By Igor Wilkomirsky

Professor Ralph Harris was interested in minor elements behavior in nonferrous pyrometallurgical processes. His approach always considered fundamental aspects and technological considerations for the assessment of different challenges that today are becoming critical, particularly for Andean sulfides ores, where the content of Va elements (As, Sb and Bi) has challenged available technologies. This reviews the status of control and monitoring of As in copper smelters to give a general framework for this now-common problem. Some selected results of R & D programs at the University of Concepción are presented in the field of roasting, presenting a novel proposition for flue dust treatment as an alternative to the classical hydrometallurgical processes for these type of materials. This presentation seeks to open a broad but precise discussion about the needs of research in this area with further experimental and physicochemical modeling. The pioneering visions developed by Professor Harris with his students are now a source of inspiration and an unavoidable source of information.

Jan 1, 2013

By Hai-Xing Fang, Chao Liu, Tao Zhang, Bing Xie, Hong-Yi Li, Cui Li

"Hongge Ore, a kind of vanadium-titanium magnetite ore containing high content of chromium, is valuable resource for extracting Fe, V and Cr in China. During present processing of the ore, vanadium and chromium were both concentrated in slag, leading to higher content of chromium in the vanadium slag than that of common one in Pan-Steel. Mineral phases and characteristics of spine! crystals, which influenced greatly subsequent roasting process, in the vanadium slag under different cooling conditions were investigated by using XRD and SEM/EDS. Results showed that vanadium slags containing various contents of chromium were composed of spine!, in which V and Cr were both concentrated, olivine and pyroxene. Growth rate of spine ls decreased sharply below 1350°C. The non-isothermal crystallization process could be described by modified Avrami equation and Ozawa equation. Avrami exponent and Ozawa index were calculated and growth mechanism of spine! crystals was discussed.IntroductionVanadium (V) as well as chromium (Cr) is important non-ferrous metal widely used in materials and chemical industries [1, 2]. Especially, both of them are important alloying elements for the production of high alloyed steels to achieve desired physical-chemical and mechanical properties. Vanadium-titanium magnetite ore in Panzhihua-Xichang area (China) is an important raw material for extracting vanadium. During the extracting process, vanadium is firstly reduced into hot metal and then concentrated in slag phase by blowing oxygen into the hot metal in converter [3]. This kind of slag containing 5~20 wt% V20 3 are usually roasted with sodium or calcium salts and then leached to obtain vanadium containing solution and final products. Current vanadium slag obtained from normal vanadium-titanium magnetite ore contains low content of Cr20 3 and chromium extraction is thus ignored. However, chromium content in the vanadium slag would be increased intensively when the Hongge Ore used, which is also important vanadium titanium magnetite in Panzhihua-Xichang area containing 0.2~0.8 wt% Cr203. Therefore, this kind of vanadium slag with high content of chromium would also be important sources for vanadium and chromium extraction. According to previous work [4], both vanadium and chromium could be extracted from vanadium slag with high content of chromium by salt roasting and leaching, which is illustrated in Fig.1."

Jan 1, 2013

By Kyle A. Perry

Pillar design formulae have existed for decades, and the guidelines for design stability factors are generally accepted by regulatory agencies and broadly used within the coal industry. Nearly all design pillar formulae are based on geometrical parameters of pillars resulting from empirical investigations, with primary focus on the pillar width-to-height (W/H) ratio and associated shaping constants from regression. The most widely used modern pillar design formula in the coal industry, the Mark- Bieniawski equation, also adheres to this principle. Common practice when applying Mark-Bieniawski equation is to use a coal compressive strength of 900 psi. This reduces the design equation to sole dependence upon geometry. However, recent studies have shown that pillar strength is highly dependent on roof and floor properties, particularly the interfaces between the roof-pillar and pillar-floor. This study utilized numerical modeling using FLAC3D to evaluate the relative effects of varying roof and floor interface and mechanical properties. The results confirm that pillar strength is significantly influenced by the properties of the coal pillar interfaces with roof and floor. The mechanical properties of the roof and floor material have only a minor impact on pillar strength when compared with interface effects. These results were used to formulate design recommendations for existing pillar design methods.

Jan 1, 2013

By Dong Liu, Zejian Yang, Yong Li, Tao Jiang, Xiangxin Xue, He Yang

"The structure, composition, morphology, and adsorption property of UV-vis light of as-prepared samples were characterized using XRD, SEM, FTIR-EDS, and UV-vis DRS. UV-visible light induced photocatalytic degradation of methylene blue ~) over Ti02-doped diopside was investigated. Experimental results show that doping Fe + induced the formation of Ti-0 or Ti-0-Si in diopside, and promoted the light adsorption property of diopside. Photocatalytic reactivity of Ti02-doped diopside obviously depended on content of doping Ti02. The diopside with 3% Ti02 exhibited the superior photocatalytic activity with 76% degradation of methylene blue under light irradiation for 3 h.IntroductionPhotocatalytic technology has been extensively studied in the process of dealing with inorganic and organic pollutants. Ti02, with its own non-toxic, stable, low-cost and other advantages, has become the most widely studied photocatalytic materials[l-SJ_ The low utilization quantum made it restricted in the practical application. SrTi03 as the representative of the perovskite[9·121, Bi2W06 for the composite oxide[13,141, also attracted wide interest in the photocatalytic studies. However, these photocatalytic material has been mostly prepared in relatively strict experimental conditions with chemical reagents, they had small production, high cost, which made them difficult for practical applications.In our country, there has 400 million tonnes of ti-bearing blast furnace slag (TBBFS) each year in the process of smelting pig iron, which has lead to waste of titanium resources and pollution of the surrounding environment. In recent years, studies have shown that TBBFS instead of pure Ti02 to be photocatalytic materials is feasible[ 151. TBBFS has not only been higher photocatalytic degradation activity for the o-nitrophenol, methyl orange, nitrobenzene and other organic matter[16-191,but also exhibited excellent in the process of dealing with inorganic heavy metals in waste water (containing Cr6+i201. If TBBFS can be successfully applied to photocatalytic technology, the will make large accumulation of titanium-bearing slag reasonable used, so as promote the re-use of energy. At present, our understanding of the photocatalytic activity of TBBFS is steadily deepening. Photocatalytic activity ofCaTi03 has been reported as one of the main minerals ofTBBFS [21'21J, However, there were few studies for Another major mineral of TBBFS - diopside which had the content of9-15%. diopside would doped with Ti02 In the process of smelting pig iron, therefore, Ti02-doped diopside's photocatalytic activity in the UV-Vis was mainly studied in this paper."

Jan 1, 2013

By D. Yuan, L. Yan, M. J. Collins, P. Kalanchey, I. M. Masters

ABSTRACT Pressure oxidation tests have been conducted by Sherritt for a refractory gold-silver project in China. The feed contained 39 g/t Au and 970 g/t Ag; the major gold-bearing minerals were pyrite and arsenopyrite. Because the feed contained a significant amount of silver, which can be refractory to cyanide leaching after pressure oxidation due to the formation of argentojarosite, the test program included investigation of methods to enhance silver recovery. The “lime boil” process proved successful and was incorporated into the flowsheet. Gold extraction from the lime boil product solids was 95–98%; silver extraction was up to 94%.

Jan 1, 2013

By Liang Shen

The Cooper River Bridge, the longest cable-stayed bridge in North America, replaces two existing bridges along U.S. Highway 17 and connects the City of Charleston and the town of Mount Pleasant, South Carolina. Two diamond shaped towers support the 1,546 ft long main span over Cooper River and allows for a 1000 ft wide navigation channel. The Charleston high-level approach is 4351 ft long and provides a 250 ft wide navigation channel for Town Creek, while the Mount Pleasant high-level approach is 2,090 ft long. Due to the high seismicity in the region, potential vessel impact, and hurricanes, large lateral loads are expected. From various types of foundations, 10-foot diameter drilled shafts were selected for their high capacity against vertical and lateral loadings. The shafts are founded on a stiff to very stiff lightly cemented calcareous sandy clay or sandy silt layer, called Cooper Marl, which underlies the coastal sediments of the interbedded clays and sands. A group of 11 shafts supports each main tower, while a rock island protects it from vessel collision. A group of 4 to 8 shafts foundations support the other piers of the main span unit. A pair of shafts supports the High Level Approach piers. The shaft tip elevations vary from 120 ft to 230 ft below water line. An elaborate geotechnical investigation was conducted on the site, including a load test program on full-scale shafts under axial and lateral loads. The results of the tests were used to calibrate the lateral and axial soil resistance. The objective of this paper is to present the different aspects of the bridge foundation design.

Jan 1, 2013