Search Documents

By H S. Welideniya, K Ekanayake

Carbon rich graphite deposits found in Sri Lanka are of inorganic origin and they occur as narrow steeply dipping veins. The vein width of these deposits varies from a few centimetres to metres, with an average vein thickness of 1 m. It is believed that the carbon rich fluid intruded into fracture zones under high pressure and the temperature has crystallised into graphite. This process has also generated many minuscule graphite veins centred on main mineralisation, which has reduced the host rock overall rock mass rating. These discontinuities could also be considered as joints with graphite infill. Graphite mining at Bogala Mines, Sri Lanka is a unique example of narrow vein mining faced with numerous wall stability issues resulting from weak graphite infilled joints.The Bogala vein type graphite orebody has an average vein width of 1 m. Overhand cut-and-fill mining method is used for stoping. The stope consists of two boundary winzes for material handling, access and ventilation. Mining is done on the strike of the vein and the average mining slice height is 2 m. A void to the height of one mined slice is left below the mining level during mining. Waste rock resulting from vein blasting and mine development is dropped into this void as fill rock. Any void height left greater than a single slice height will increase stresses in the stoping zone. This will increase formation of rock blocks and their effective separation from wall rocks. Split miniscule veins occurring around main mineralisation intensifies rock block formation in an environment of mining induced stress release. Consequently, any rock blocks sliding into stopes on graphite infilled joints will behave under constant normal stiffness (CNS) conditions and their shear strength will converge rapidly towards remoulded shear strength of graphite alone. Unlike with general infill deposited in joints, graphite has a very low friction angle and with its slippery nature, a small thickness may affect in great deal to reduce joint shear strength.In addition to immediate filling of excavated voids, controlled vein blasting and spot bolting have improved mine safety. Furthermore, rock bolts connected to each other through iron plates and anchored to anchor bolts installed in non-fractured solid rock are practiced to stabilise rock falls and wedge failures in narrow vein graphite mining. These practices have significantly contributed to safe mining without any rock bursts and catastrophic failures.CITATION:Welideniya, H S and Ekanayake, K, 2012. Challenges faced by narrow vein graphite mining and influence of graphite infill on wall stability, in Proceedings Narrow Vein Mining 2012 , pp 71-76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By B M. Wilson, B J. Turner, S Sinclair, R J. Buerger

The Trident Gold Deposit is centred on the historical Higginsville Mining Centre, between the world class gold centres of St Ives (+15 Moz) and Norseman (+6.5 Moz) in Western AustraliaÆs productive eastern goldfields. It lies towards the southern end of the Norseman-Wiluna Greenstone belt in the Archaean Yilgarn Craton. The current in situ resource for Trident is estimated at 840 000 ounces, with production to date in excess of 500 000 ounces.Trident is hosted primarily within a thick, weakly differentiated gabbro with subordinate mafic and ultramafic lithologies and comprises a series of north-northeast trending, shallowly north plunging ore zones. The deposit comprises two main mineralisation styles; thin, lode-style, nuggety laminated quartz veins (Athena and Artemis) that formed along major shear zones primarily at the contacts between the various mafic and ultramafic lithologies; and large wallrock-hosted ore-zones comprising sigmoidal quartz tensional vein arrays and associated metasomatic wall rock alteration (eastern zone, western zone and Apollo) hosted exclusively within the gabbro.The thin laminated quartz vein lodes are important to the Trident Gold Deposits production profile as they constitute 33 per cent of the metal from only 14 per cent of the tonnes. The delineation, grade estimation and extraction of these lodes require a disproportionate amount of geological and engineering input due to the small scale variability in width, grade and direction. Over time, a robust and thorough process has been developed at the Trident Gold Deposit to understand and then successfully mine these complex mineralised systems.CITATION:Sinclair, S, Wilson, B M, Buerger, R J and Turner, B J, 2012. The mining industry needs to be shaken and stirred, in Proceedings Narrow Vein Mining 2012 , pp 155-166 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By A Richmond

"In some lode-style gold deposits the geological (lithological) uncertainty may have similar economic significance as the grade uncertainty. In the absence of precise knowledge of the deposit geology, geological models of these types of deposits that are used to constrain spatially the estimated (or simulated) grade values may influence significantly the contained metal. Methods for assessing geological uncertainty quantitatively are rarely considered due to their perceived inability to consider exhaustive geological interpretations, and resulting models that often appear geologically unrealistic. Furthermore, should the lodes have been subjected to folding, or where the mineralisation continuity does not follow a planar orientation along strike or down dip, standard methods of variography and interpolation using linear vectors in space often do not provide a good representation of continuity. An alternative approach is to relate spatial samples from adjacent drill holes using an unfolding plane.The paper demonstrates conditional simulation of the geometry and gold grades of a folded lode-style deposit where:simulation of lode geometry considers explicitly the geologistÆs interpretation, andsimulation of gold grade values that consider explicitly the folded nature of the lodes.The results are contrasted to the traditional approach of linear vectors in real space for a single lode interpretation.CITATION:Richmond, A, 2012. Conditional simulation of a folded lode-style gold deposit, in Proceedings Narrow Vein Mining 2012 , pp 149-154 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 26, 2012

By N S. Rauert

The Barrick Gold Granny Smith underground operation located at the Wallaby deposit is currently in a transition period from a near surface operation in ramp up mode to a fully operational deep mining operation with annual production exceeding 1 Mt/a. A key element in this process has been the project execution of the Wallaby Deeps project from initial scoping study in 2007 to the major production component of the Wallaby operation by 2013.The Wallaby Deeps project serves as an example of how an ongoing detailed study program can be integrated into a day to day mining operation assessing risk and mining application in a perceived challenging narrow vein geotechnical environment prior to mining. A detailed study phase to feasibility level is carried out prior to the mining each zone of Wallaby with mining approval only granted on study completion with full justification.A central element in this process is an optimisation study that utilising the Mineable Shape Optimiser (MSO) and Schedule Optimisation Tool (SOT) software tools developed by AMIRA Ltd PRIMO research project is used to carry out an NPV value based option study. This optimisation process being then tempered to reality by a predefined practicality assessment process utilising extensive peer review by operational and study team members as well as industry experts.Other challenges facing the Wallaby Deeps project include the requirement to maintain the ramp up production profile to full production by 2012 without disruption but with pressures of an ongoing geological resource to reserve conversion program essential for the study process and mining approvals and also development rate achievement.To date these challenges are being met with integrated planning and the value of the study program itself. Production in 2012 year to date is well on the way to annual production rate exceeding 1 Mt/a.CITATION:Rauert, N S, 2012. Wallaby Deeps - from the optimal opportunity to reality, in Proceedings Narrow Vein Mining 2012 , pp 207-214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By M J. Ireland, D P. Horne, S J. Simpson

The Sinclair Nickel Project, wholly owned by Xstrata Nickel Australasia (XNA), includes an underground mine, a concentrator, a village, an all-weather airstrip and associated mine infrastructure. The operation is located 70 km north of Leonora in the prospective and historically productive eastern Goldfields region of Western Australia. Xstrata Nickel has successfully developed the Sinclair deposit into a 350 kt/a operation since its discovery in November 2005, with contained nickel metal production to date in excess of 10 600 t, of which 5500 t is from the underground operation.The narrow, continuous, medium-grade Sinclair nickel sulfide deposit accessed by the Phoenix Decline has a shallow 15¦ - 20¦ plunge that is approximately 1000 m long down dip and open at depth to the north. The flat plunge and low-grade nature of the orebody presents challenges regarding the amount of horizontal waste development that can be economically excavated, which in turn affects ventilation, egress, mine services and diamond drilling.The mineralisation is hosted between an ultra mafic hanging wall and a basalt footwall and is being mined using a bottom up, sublevel open stoping method. The stopes are retreated to a central access, filling voids in the process with waste mullock where possible and using cemented mullock fill where end exposure is required. Tight filling the flat dipping hanging wall has proved to be challenging given the angle of repose for the waste mullock fill is steeper than the angle of the hanging wall.Reconciliations of mine performance against the original feasibility study show positive changes and operational optimisations enabling Sinclair to achieve its mining targets in a safe, sustainable and economic manner. This paper discusses the mining operations associated with the first two years of the Sinclair Underground Nickel Project, providing an overview of the various issues encountered and the lessons learnt in the process.CITATION:Ireland, M J, Horne, D P and Simpson, S J, 2012. Overcoming mine design and production challenges at the Sinclair underground nickel project, in Proceedings Narrow Vein Mining 2012 , pp 37-48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By Ron Galisky

Generalmente, las empresas mineras deben decidir si reemplazan los equipos anteriores por unos nuevos o continuan con los mismos . Los criterios se basan en el nivel de deterioro, cambios tecnológios, demandas medioambientales, o cambios de requerimientos. En ese sentido, el presente texto describe la metodología adecuada para la gestión de cambios de equipos a través de la teoría clásica del CAE donde se abordan tales problemas. Así también se plantea el uso del modelo CRU Strategies. La metodología ayuda en la planificación y gestión operativa y en los presupuestos de inversión anuales típicos en la industria.

Mar 1, 2012

By José Valle Bayona

El presente texto describe la gestión de competencias en seguridad y salud ocupacional en el actual D.S. N°055-2010-, el cual contiene varios apartados de capacitación. Así también, se plantea la revisión de una propuesta de estructura y relación entre competencias laborales y educativas paraí formular un ejercicio con un cuadro orientador sobre los contenidos de los cursos y otras experiencias de capacitación incluidos en el Reglamento.

Mar 1, 2012

By S. J. Jung

El presente texto describe las causas de origen relacionadas con los tipos de accidentes mineros y las lesiones desarrolladas por tales causas. Asimismo, se espera descubrir la dinámica de las causas de origen que ocurren con frecuencia en el mundo tecnológico.

Mar 1, 2012

By J. T. Carlson

Dolomite [CaMg(CO3)2] is an intolerable impurity in phosphate ores, due to its MgO content. The need to develop a cost-effective method for the removal of dolomite from high-MgO phosphate ores becomes increasingly important as high-grade reserves become depleted. The jigging process has been investigated as a method for the beneficiation of phosphate ores. A laboratory-scale jig was constructed and tested using a semicontinuous, ?through-the-screen? jigging process. Two types of sedimentary phosphate ore were used; a sample from Plant 1 in the 4.00 x 0.85-mm size range, containing 1.55% MgO, and a sample from Plant 2 in the 3.40 x 0.85-mm size range, containing 3.07% MgO. These were tested, using previously optimized jigging parameters, at high and low feed rates. For the Plant 1 phosphate ore, a phosphate concentrate that contained 0.89% MgO was achieved with a bone phosphate of lime (BPL) recovery of 32.0%. For the Plant 2 phosphate ore, a phosphate concentrate that contained 1.38% MgO was achieved, with a BPL recovery of 74.7%. Minimum achievable MgO grades were also determined by analyzing hand-separated phosphate samples.

Feb 1, 2012

By P. Zhang

This paper gives a review of promising technologies for phosphate processing, and covers flotation, analysis and process control, as well as tailings treatment and utilization. Air bubbles of less than a µm in size, combined with relatively large bubbles, have been demonstrated, both in the lab and on a pilot scale, to improve flotation dramatically, by reducing reagent use while improving product grade. Innovative use of polymers has allowed rapid dewatering of fine tailings with a final product that does not segregate. The first online laser-induced breakdown spectroscopy (LIBS) analyzer was created, allowing rapid analysis of wet samples using the laser technology. Many large commercial projects are successfully pursuing the utilization of phosphogypsum.

Feb 1, 2012

By N. Chow

The recovery of manganese from lower-grade resources has been studied for a number of years. Of key importance in prior work was the discovery that higher-valent manganese can be readily leached with sulfurous acid. This eliminates the need for high-temperature reduction roasting that is conventionally used in processing high-grade material. High-temperature roasting is energy intensive, emits a large amount of carbon dioxide and would not be economical for processing lower grade material. While the prior work provides important information for extracting manganese from lower-grade resources, the production of unwanted byproducts and high water and energy usage has limited its commercial use. This paper describes the results from laboratory work that demonstrate solutions to problems that to this point have precluded commercial development. Preliminary mass and energy balances show that a significant opportunity exists in producing manganese with this hydrometallurgical scheme in a low-cost, environmentally friendly manner. The emphasis of the work is on low water use, low overall energy use and economic destruction of unwanted byproducts.

Feb 1, 2012

By R. Raitani

Five kaolin crudes from the state of Georgia in the U.S. were investigated for processability with chemically enhanced magnetic separation (CEMS) technologies developed by Cytec. The technologies used magnetic reagent alone or in conjunction with specialty chemicals to selectively agglomerate and magnetize the desired minerals (impurities) to be removed by the conventional magnetic separation equipment. All crudes indicated treatability using CEMS. Results indicated that CEMS technology could be applied to different kaolin crudes to obtain a product with titanium impurities less than 0.6% TiO2 from individual crudes. The features and benefits of the technologies were also reviewed.

Feb 1, 2012

By T. J. McKeon

Gravity separators such as spirals are commonly used in multistage cleaning and scavenging circuits to improve the quality and recovery of concentrates produced in the industrial minerals industry. Unfortunately, field surveys suggest that many industrial operations are poorly configured in terms of equipment layout. This shortcoming can often be attributed to a failure by engineers to make use of fundamental process engineering tools for circuit design. One of the most important of these is linear circuit analysis. This powerful tool makes it possible to mathematically compare the relative efficiency of circuit configurations in advance of experimental testing. This article provides a basic review of the linear circuit analysis concept and discusses some of the key insights it provides for the layout of multistage circuits. An industrial case study is provided to show the tremendous impact that this process engineering tool can have on the design of multistage spiral circuits in a heavy mineral wet plant.

Feb 1, 2012

By R. Merkl

Since the 1940s, decanter centrifuges have become more important for increasingly complex solid-liquid or solid-liquid-liquid separation processes. Sometimes processed industrial or metalliferous minerals are abrasive or are treated with corrosive chemical agents. Traditional mining applications include the processing of coal, gravel and other products, where low-speed decanters, as well as screen bowl decanters and filters, dominate. These have been increasingly replaced by high-speed decanters during the last decade. Decanter centrifuges also started to play a key role in applications such as drilling muds, processing carbonates and separating SX crud in copper platinum ore concentrations of nickel and gold. Communication between machine producers and mineral processing engineers is vital for the right choice of materials and the design of the right decanter centrifuge for the individual process.

Feb 1, 2012

By R. J. Pruett

Selective flocculation enables the production of high-brightness kaolin products from kaolin ore once considered too poor in quality for beneficiation into paper-coating pigments. Anatase, Ti(1-X)FeXO2, with X = 0 to 0.05, is a common iron-bearing impurity in sedimentary kaolin that can be unresponsive to kaolin beneficiation processes, such as magnetic separation, due to its extremely fine particle size (<0.3 µm), or chemical bleaching, because of its chemical stability. Described here are selective flocculation technologies that separate anatase by flocculating anatase or flocculating kaolinite from dispersed slurries. Applying the advances in the chemical and mechanical dispersion of ultrafine particles and the selective aggregation of kaolinite or anatase particles have resulted in the selective flocculation processes practiced today that have increased process recoveries from those technologies practiced beginning in the 1960s.

Feb 1, 2012

By X. Yin

Surface force measurements based on atomic force microscopy (AFM) are used to describe the wettability of surfaces, specifically kaolinite basal plane surfaces at a high resolution. The kaolinite particles (~500 nm) were ordered with either the silica tetrahedral face exposed or the alumina octahedral face exposed, and surface force measurements were made between a hydrophobic diamond-like-carbon (DLC) tip and the kaolinite faces at pH 4, which is around the isoelectric point of the DLC tip. Under these conditions, the effect of electrostatic interaction should be eliminated and only van der Waals interactions and hydrophobic-hydrophobic interactions are expected to contribute to the surface force. The wettabilities of the surfaces were determined from the magnitude of the surface force. Wettabilities of the kaolinite basal planes thus determined were compared with the corresponding wettabilities of talc and mica surfaces, which are well-known to be naturally hydrophobic, and hydrophilic surfaces, respectively. The results reveal that the silica tetrahedral face of kaolinte has a modest level of hydrophobicity, which may be due to the lack of hydrogen bonding sites. In contrast, the alumina octahedral face showed no hydrophobicity, since a layer of surface hydroxyl groups is present at the alumina face, resulting in a relatively strong interaction between this surface and water molecules. It is expected that, with a better understanding of the surface properties of kaolinite, further improvements in flotation separations and dewatering may be achieved.

Feb 1, 2012

By Doris Hiam-Gálvez

El presente trabajo describe las últimas tecnologías que mejoran la minería en América Latina y la eficacia en el procesamiento del mineral. Así también se revisa el modo innovador de energía a través de la fundición de sales con energía solar, particularmente en regiones desérticas de América del Sur. Cada tecnología ofrece mejoras sustanciales en eficiencia, capital, y costos operativos y contribuye a la reducción el impactom ambiental de las operaciones mineras.

Feb 1, 2012

By J. Kou

The adsorption process, density and structural property of the oleate layer adsorbed onto a hydroxyapatite (HAP) surface at six different concentrations and three pHs (pH 8, 9 and 10) have been studied using the technique of quartz crystal microbalance with dissipation (QCM-D). The present study demonstrated the versatility and accuracy of the QCM-D for surface adsorption characterization. The real-time measurements of frequency and dissipation shifts with a hydroxyapatite-coated sensor revealed changes in the hydroxyapatite surface during the entire adsorption process. Chemisorption and surface precipitation of sodium oleate were also observed on the surface of hydroxyapatite through the use of Fourier Transform infrared spectroscopy(FTIR). Chemisorption dominated at low concentrations and high pH values and formed a rigid and thin adsorption layer. Surface precipitation of calcium oleate and micelles dominated at concentrations higher than critical micelle concentration (CMC) and lower pHs and formed a thick but dissipated adsorption layer with a high hydration level. Three distinct adsorption behaviors were identified from the different slopes of ?D-?f plots. The adsorption density was less than a monolayer at concentrations <0.164 mM, but increased significantly at concentrations higher than 0.821 mM at all three pHs. The critical concentration at pH 8 was 0.33 mM, which was lower than at pH 9 (0.821 mM) and pH 10 (3.3 mM).

Feb 1, 2012

By Mirian Mamani

El presente texto describe una base de datos geológica que comprende: geología integrada, estructuras definidas en campo de mediciones y edades en actividad, ocurrencia de minerales metálicos, mediciones de aeromagnetometría y geocronología de rocas ígneas y metamórficas donde es importante delimitar los dominios geotectónicos para la exploración de yacimientos. En ese sentido, el presente texto describe las nuevas zonas propicias para la exploración en el sur del Perú a través de la identificación de fallas corticales y dominios geotécnicos dentro del proyecto GR1: Geología de la Costa Sur y vertiente oeste de la Cordillera Occidental de la Dirección de Geología Regional del Ingemmet.

Feb 1, 2012

By Leduar Ramayo Cortés

Dado que en la industria minera, la exploración profunda representa uno de los costos de perforación y capacidad de gestión de metodología para las empresas, se ha previsto el uso de nuevas tecnologías como la Titan 24. En ese sentido, el presente texto señala dicha tecnología como la más adecuada para realizar estudios profundos de depósitos minerales en minas activas que representen grandes retos para las empresas. Así también se describe los casos históricos de la aplicación de Titan 24 en diversos proyectos.

Feb 1, 2012