Search Documents

By M. Wu, A. Kharicha, J. Bohacek, A. Ludwig

"During the horizontal spin casting of rolls, vibrations and mould deformations seems to have a significant effect on the final quality of the product. Sources for vibrations can be found in the poor roundness and a static imbalance of the chill itself. The bending of the mould axis is also considered. Both, vibrations and axis bending, are used as an input for CFD simulations of the flow dynamics of the liquid metal inside the rotating cylinder. The aim is to study the feedback of the free surface behavior in terms of wave propagation and various wave shapes. Introduction The horizontal spin casting process (HSC) is a casting process that has several advantages over the traditional gravity casting processes. Centrifugally cast products have a high degree of metallurgical purity and homogeneous microstructure. A significant gain is observed for the rupture strength, the rupture strain, and the Young modulus. These properties naturally depend on the centrifugal force and thus, the best mechanical properties can be found at the largest distance from axis of rotation. However proper selection of the angular frequency has to be done in order to prevent the so-called ""metal rain"" i.e. metal droplets can fall down from the upper part of the cylinder due to a too weak centrifugal acceleration. In the same time excessive speeds can lead to the appearance of longitudinal cracks caused by the hoop stress in the initially solidified layer. From empirical knowledge other parameters have important influence on the casting products, it includes the pouring temperature, the pouring rate, the mould coating etc. Recently the presence of natural or forced vibrations have been identified as possible additional factors to be taken into account [1-2]."

Jan 1, 2012

By Douglas Bartley

As the economy continues to slowly recover, our industry continues to finds ways to increase productivity while being forced to cut costs. The drilling and blasting process is the starting point of any aggregate or mining process. Many people refer to it as the “Primary Crusher” as it will always be more efficient to crush rock with explosives energy than it will be mechanical energy. It is the more efficient use of this energy that is addressed in this paper.

Jan 1, 2012

By Jiayan Li, Yi Tan, Yao Liu, Yaqiong Li, Shenrui Wu

"A metallurgical grade silicon (MG-Si) refining concept process was presented. Under vacuum conditions, silicon was selectively oxidized by high purity silicon dioxide to form gaseous silicon monoxide while impurities with low vapor pressure in MG-Si were rejected in residue; Then high purity silicon was obtained from the disproportionation of condensed silicon monoxide; and by-produced silicon dioxide was recycled for the oxidation step. Thermodynamics on boron rejection during the oxidation were studied in this work. In the temperature range of 1200-1800K, the saturated vapor pressure of boron, and the Gibbs free energy changes, the equilibrium partial pressures of silicon monoxide and boron oxides of potential reactions were calculated. And the effect of boron activity in MG-Si was also discussed. The results indicated that boron in MG-Si can be rejected during the oxidation and it showed the potential for the further development of the new refining process.IntroductionAs global energy consumption growing dramatically, higher prices of energy and global warming problem have attracted more and more attention [1]. As a clean and renewable energy industry, the photovoltaic (PV) industry converts solar energy to electricity using solar cell device and has a growth rate of about 30% in recent years. It has caused a shortage of silicon feedstock due to that about 90% of solar cells are made of crystalline silicon. And high energy consumption during the production of silicon material, i.e. solar grade silicon (SoG-Si), is main obstacle for its mass production."

Jan 1, 2012

By W. C. Joughin

A risk evaluation model has been developed that enables the quantification of expected injuries and economic losses resulting from rockfalls associated with a support system in a given geotechnical environment, which is described in Part I (Joughin et al., 2011b). Part II presents the validation of the risk evaluation model. Underground mapping of joints and rockfalls was carried out to provide data for field calibration of the model. This survey was limited to small rockfalls, due to the relatively short period of mapping. Therefore the model was also correlated with rockfall and rockfall injury data collected by mine personnel. The analyses showed that the model provides a reasonable estimate of the expected frequency and size of rockfalls and the frequency of rockfall injuries, but further work is required to enhance the model. Three case studies are presented, which show the benefits of improved support systems from both economic and safety perspectives. This work has demonstrated that the risk evaluation model and the software developed are immediately useful, but further work is required to develop and improve the tools.

Jan 1, 2012

By S. Lubbe

South Africa and Australia are the biggest suppliers of zircon sand to the international zirconium industry. However neither South Africa nor Australia is well known for zircon beneficiation. Geratech Zirconium Beneficiation Ltd (GZB) continued with additional research on sodium hydroxide (NaOH) cracking of zircon sand during 2002-2003. In 2003 GZB started extracting zirconium from zircon sand by means of NaOH cracking on a commercial scale. Experience has shown that temperature profile and atmospheric control inside the furnace is crucial for the beneficiation of zircon sand. Silica carryover to zirconium chemicals could result if a high temperature is used. Once the sodium silicate is extracted from the sodium zirconate and dissolved in hydrochloric acid, two distinct routes can be followed to precipitate various zirconium chemicals. The most common route is to precipitate zirconium oxychloride crystals (ZOC), with subsequent purification from all contaminants (crystal route). Less known is the process (liquid route) that involves the direct precipitation of zirconium basic sulphate (ZBS). This route will yield a less pure product, with contaminants such as silica and titanium. An important factor in this route is the prevention of silica gel formation, which could hamper final product filtration. For applications like paint drying (zirconium octoate) or antiperspirants (zirconium hydroxychloride) low levels of contaminants have no effect on the final product. The advantage of the liquid route is fewer production stages compared to the crystal route. The disadvantage of the liquid route is that the market for the products will be significantly smaller. The optimum solution could be a plant design that could cater for both routes. Another example of an application of zirconium chemicals is the use of ammonium zirconium carbonate (AZC) in the paper industry. Zirconium basic carbonate (ZBC) is dissolved in ammonium carbonate to produce AZC solution. AZC is used mainly in European countries in the paper industry. For example, carton boxes were initially produced with formaldehyde as the binder, however, it has now been replaced with AZC since formaldehyde is considered toxic. AZC reacts with the cellulose fibres in the paper to act as the binder. The resulting product is not toxic, and printing ink dries very quickly due to the porous paper structure. Other applications of zirconium chemicals involve the use of acid zirconium sulphate tetrahydrate (AZST), zirconium orthosulphate (ZOS), potassium zirconium carbonate (KZC), and zirconium hydrous oxide (ZHO). Fluoride-based zirconium chemicals like zirconium tetra-fluoride (ZrF4) and hexafluoro-zirconic acid (H2ZrF6) are used in the aluminium industry. Zirconium oxide (Zr02) can be produced from any of the abovementioned precipitated chemicals via a high-temperature decomposition process. The physical properties of such oxides can differ tremendously, depending on the final application. The fired density of sanitaryware is typically 5.8 g/cm3, compared to milling media at >6.1 g/cm3. The required fired density is achieved by controlling the precipitation and decomposition conditions for these two oxides. The same applies to stabilized and mixed oxides, for example where zirconium oxide acts as an oxygen carrier in fuel cells.

Jan 1, 2012

By Hande Cavus, Ibrahim Yusufoglu, Cem Kahruman

"In this study, ammonium tetramolybdate (ATM) was obtained as the intermediate product of ammonium heptamolybdate tetrahydrate (AHM). The thermal decomposition mechanism of ATM was investigated under nonisothermal and isothermal conditions in air and inert gas atmospheres. Nonisothermal experiments were carried out by TGA/DTA/MS while TG was used for isothermal conditions. Characterization of the decomposition products were carried out by XRD and FT-IR. The thermal decomposition of ATM in air proceeds in a single step and forms M0O3 while [(ÍÇ4)2è]ïïï83Ìïè3 and molybdenum suboxide (Ìïè3.÷, ÷=0.025) were obtained in the first and the second steps of thermal decomposition in He, respectively. Activation energies, frequency factors and kinetic model equations were determined for thermal decomposition reactions. Fractional conversion-time diagrams were compared with diagrams drawn according to kinetic model equation.IntroductionM0O3 is usually used as catalyst in industry [1]. AHM is the basic source to produce molybdenum containing catalysts used in petrochemistry [2]. The oxides of Li, V, W, Te, Bi and Sn are doped in M0O3 to produce catalysts, which find commercial applications in the industry. The properties of M0O3 are affected by dissolution, settling, calcination, drying and thermal decomposition processes [1]. There are several studies in the literature about the thermal decomposition of AHM and the characterization of the decomposition products in different gas atmospheres and at various heating rates [3-19]."

Jan 1, 2012

By John Hayden

The nation runs on energy. It is essential for the economic growth and national security of the United States that the nation has an adequate, sustainable, environmentally acceptable and economically viable balanced supply of energy sources, (e.g., coal, petroleum, nuclear, natural gas, solar, wind, geothermal, biomass, hydroelectric power). Therefore, the allocation of mineral raw materials to the energy-producing sector of the economy must be a top priority that requires the total demand for energy-related materials be judged in terms of domestic supply (Fig. 1).

Jan 1, 2012

By J. A. Herbst

Professor Klaus Schönert and his students used fundamental physics to develop many of the principles required for the design and scale-up of "Gutt Bett Zerkleinern" devices such as the high pressure grinding roll (HPGR) or the high pressure roll crusher (HPRC). As the equipment evolved so have the tools used for its selection and analysis. In the current paper discrete element modeling (DEM), Metso's proprietary Fast Breakage simulations, and Schönert's packed bed piston test are combined with energy based population balance models (PBM) to yield an alternative to ore characterization and equipment selection by pilot plant testing. The resulting methodology is used to take the next step in understanding these devices with a view toward predicting plant performance. This paper describes a journey beginning with precise modeling of a small HPGR including stud geometry and system hydraulics. A key to predicting performance is the accurate modeling of individual particles, their motion in the machine, the probability of breakage and redistribution of fragments, and the inter-particle breakage events that occur between the rolls at different pressures, speeds and moisture levels. Advanced DEM simulations and particle breakage characterization methods provide the necessary technology. The resulting combined models were validated using a small diameter laboratory scale unit. The validated physics based model was used then used to predict the performance of plant scale units using a specific energy based scale-up method. Scale-up results are analyzed in terms of power draw, throughput, and discharge product size distribution.

Jan 1, 2012

By Laurentiu Nastac

"The importance of investigating solute redistribution during the unidirectional solidification of multi-component alloys is broadly discussed in the literature. A previously developed analytical model that was experimentally validated for Al-Cu, Sn- Bi and Fe-Si dilute binary alloy systems is used in this article to study in detail the solute redistribution, the liquid/solid interface stability based on an extended transient constitutional undercooling criterion and the size of the initial transient region during the unidirectional solidification of Ti-6-4 and Ti-17 alloys. A comparison between Ti-6-4 and Ti-17 alloy systems with respect to interface stability and the size of the initial transient region is also provided. The effective partition coefficients of the alloying elements in these alloys were determined based on specially designed experimental measurements.IntroductionThe importance of investigating solute redistribution during alloy solidification is broadly discussed in the literature [1-5]. One of the relevant applications of this study would be the mathematical modeling of equiaxed and columnar solidification of multicomponent alloys. This includes the instability of the solid/liquid interface. There are several mass and heat transfer processes that involve the calculation of solute redistribution during directional solidification such as industrial directional solidification processes, continuous casting, remelting processes, Czochralski crystal growth technique, floating zone techniques, etc."

Jan 1, 2012

By Zhangm Mingming

Three samples received from the EAF shop were characterized by chemical, X-ray diffraction (XRD), optical microscopy (OM) and scanning electron microscopy (SEM) methods. The objective of this characterization work was to investigate the occurrence of nickel, copper, zinc, sulfur and phosphorus and to identify their origin and associations with iron minerals in the concentrate samples from the mines. The samples were identified as MINERAL, PELLET, and HRD. The latter is the DRI product. All three samples were received as fine powders. The results indicate that, in the mineral sample, magnetite is the major iron oxide mineral with hematite as a second phase based on the OM and XRD studies. Pyrite [FeS2], chalcopyrite [CuFeS2] and bravoite [(Fe,Ni)S2] are the major sulfide minerals. Trace amounts of apatite [Ca5(PO4)3(F,Cl,OH)], wardite [Na4CaAli2(PO4)8(OH)8 6H2O], giniite [Fe;(PO4)4(OH)3 2H2O] and vivianite [Fe3(PO4)2 8H2O] were identified by SEM and XRD. Microscopic studies also indicated that most of the sulfide grains in the mineral sample are present either as liberated fine particles (about 10 microns) or as inclusions within the magnetite and hematite grains. XRD studies revealed magnetite as the major mineral with subordinate amounts of hematite and pyrite confirming the microscopic findings. Copper, nickel, and zinc are mainly present as chalcopyrite, bravoite, and franklinite [(Zn,Mn,Fe)(Fe,Mn)2O4] in trace amounts in the mineral samples, respectively. Impurities carry over to the pellet and HRD samples. Chemical analyses of the three iron-bearing samples indicate that sulfur and phosphorus in the pellet sample exceeded the specification. Since liberated pyrite and chalcopyrite particles were observed in both the mineral and pellet samples, magnetic and flotation processing routes should be effective for sulfide removal but at the cost of iron losses. The high phosphorus content of all three samples indicates that there are phosphates which are difficult to remove by the current concentrating processes (magnetic separation and flotation).

Jan 1, 2012

By Ledjane Barreto, Tulio Flávio Accioly de Lima e Moura, Wilson Acchar, Antonio Carlos Silva da Costal

"Clays are common ingredients in pharmaceutical products both as exclplents and active substances. Clay minerals are naturally cationic exchangers and they may undergo ion exchange with basic drugs in solution. Smectites, and montmorillonite have been studied due their high cation exchange capacity as compared to other silicates. Recently a patented study reports the use of attapulgite as the encapsulating agents both for the protecting the active substance and modulating release into the body. Some clays such as kaolinite, smectites, talc, etc are also used as dermatological protectors. Sepiolite and smectites have the ability to form complexes with organic compounds with absorb ultra-violet radiation, enabling them to be used in sun screens with protection factors. The objective of this work is to characterize the attapulgite in order to study the potential use of this clay material in the human health.IntroductionSince the begimling of time, nature has served humanity as a source of various raw materials. Among these, clays such as kaolinite and ilitte are common ingredients in the tile production. Recently, special clay materials have been investigated in order to identifY new potential uses of these class of materials. Clay materials are natural raw material and have excellent properties such as low toxicity, good biocompatibility, making them a good material to be used in biological applications. Attapulgite (paligorskite) and sepiolite is so called special clays. These special clay materials are very sin1ilar and have a great potential to be used in some technological areas due their special catalytic, sorptive and colloidal-rheological properties [1-8]. Recently some works have reported the use of these special clays materials for many applications such as drug delivery, wound dressing, oil absorbent, pesticides, fertilizers [9-12]. Brazil has a significant reserve of attapulgite located in Piaui state, making the study of the potential of this mineral in special areas, very attractive. Attapulgite is classified a fibrous alluminous silicate material and shows the presence of micro pores and channels, fine particle size and high surface area making this material a good candidate alternative material to be used in many industrial applications [6,8,9,11,12]. The objective of this work is to characterize the physical and microstructure of attapulgite."

Jan 1, 2012

Due to deposit shape and dimension, narrow vein makes reserve modeling, geological control, stope design, drill and blasting more challenging. It needs high standard quality control as errors can be created easily, which could cause significant amount of ore loss or dilution. From channel sampling, survey control, reserve modeling, drill hole design, blasting, communication with underground drillers to backfill, this paper illustrated every step and its quality control of a long hole stope mining. Compared to other narrow vein mining methods (cut and fill and shrinkage), long hole stoping means higher production, less labor, and significantly lower cost when deposit characteristics allowed.

Jan 1, 2012

By Zheng Wei, Jian Cheni, Zhenliang Weng, Wei Liang, Hongbo Zhu, Jinhui Peng, Linqing Dai, Qianxu Ye

"By testing the dielectric constant and the dielectric loss factor of concentrated Dahongshan, mill scale, anthracite and light-burned dolomite in different frequency and temperature, and by studying the temperature-rising characteristics of the materials in the microwave field of 2.45GHz in frequency, the research in the paper shows that to reach at 1250°C under the same condition -2KW the microwave power and 30g the mass --the time concentrated Dahongshan takes is 330s, whereas the millscale is 855s and the anthracite is 820s. About the last one, the higher the temperature is, the stronger the absorptivity is. After the temperature has rose to 400°C, the anthracite's absorptivity increases dramatically. The result of the research would serve as the foundation of the further study on making direct reduced iron by microwave heating.1. IntroductionUnder the microwave fields, materials' dissipation of dielectric bodies would generate thermal effect. Therefore, the dielectric constant and the dielectric loss factor are closely related to materials' ability of absorbing microwave energy-the larger the dielectric constant and the dielectric loss factor are, the stronger the material's ability of absorbing microwave energy is, and the better the thermal effect would be[1-2]. In order to research how to make reduced iron from iron ore fines by microwave heating deeply and systematically, the test of raw materials' dielectric constants and dielectric loss factors are of the essence. What's more, because a mineral' conductivity is influenced by its components and crystal structure[3], it is necessary to study different materials' different temperature-rising characteristics; hence such studies would provide theoretical foundation of further research."

Jan 1, 2012

By P. Chris Pistorius

"Use of coke in blast furnace ironmaking is the main origin of carbon dioxide emissions from integrated steelmaking. Use of pre-reduced iron feedstocks would reduce the coke rate and, if pre-reduction were carried out with natural gas, would decrease the overall carbon intensity of ironmaking. Blast furnace productivity would also increase, because the blast volume per unit of hot metal would decrease. This paper shows that these trends can be predicted quantitatively, by using a conceptually simple Rist-style blast furnace mass and energy balance, assuming furnace productivity to be limited by the tuyere gas flow rate. Such predictions would assist in optimizing the choice of the degree of reduction and relative amount of pre-reduced blast furnace feed.IntroductionSteelmaking is responsible for some 5% of world CO2 emissions, at a rate of approximately 1.9 tonnes of CO2 per tonne of cast steel [1]. In integrated steelmaking, the ultimate source of most of the CO2 emissions is coke, the indispensible (and expensive) fuel and reductant for blast furnaces. There are several research programs underway worldwide which seek to lower the carbon intensity of ironmaking; one of the largest is the European ULCOS program [2], in which the main proposed change to blast furnace ironmaking is to scrub CO2 from the furnace off-gas (for possible sequestration), recycling the remaining gas to the furnace. To limit the recycling nitrogen load, oxygen rather than air is used to combust coke.A conceptually simpler approach is to charge prereduced feed (direct-reduced iron) to the blast furnace. This approach has been used for some two decades at the AK Steel Middletown plant, where some 200 kg of direct-reduced iron (DRI) is charged per tonne of hot metal [3]. The Middletown blast furnace has exceptionally high productivity (rate of iron production relative to the furnace hearth area), simply because less coke is required per ton of hot metal if part of the feed is already metallic. Midrex [4] has provided some quantitative predictions of the implications of DRI use in the blast furnace, stating that for every 10% of Fe in the feedstock that is in metallic form, the fuel requirement decreases by 7% and the productivity increases by 8%."

Jan 1, 2012

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Jan 1, 2012

By O. F. Brown

The use of quality materials (aggregates and asphalt binder) in optimal proportions is the key to producing optimally performing hot mix asphalt (HMA). The Superpave mix design standard in the US introduced specific volumetric and binder property requirements in HMA design. Different methods for HMA constituent proportioning have been proposed in various guidelines. The design process to determine the HMA blend is currently iterative and engineers rely almost exclusively on experience. This approach is time consuming and often does not result in cost-optimal HMA mixtures. This paper introduces a mixed integer linear programming (MILP) optimization model for hot-mix asphalt constituent proportioning. The MILP model minimizes the total mix cost while satisfying all the volumetric, binder and mix property specification requirements. The model has been successfully validated with real-life example. The aggregates and binder ratios from the model were in close agreement with those from the contractor. The Bailey ratios and the gradation constraints were also satisfied. The cost of the optimal mix was $0.804/Mg less than that of the contractors?. This marginal reduction might make all the difference in an industry that is highly competitive. The MILP model also demonstrated that adding RAP to the contractor?s design would reduce the cost of the blend by $5.74/Mg. The virgin binder content was reduced by 1% because of the recycled asphalt contained in the RAP. This work represents the first successful attempt in incorporating both aggregate and asphalt performance requirements into the optimization formulation. Applying these models will ensure the minimum cost mix that meets all constraints and will increase profit margins for plant operators.

Jan 1, 2012

By Alexander Garcia

Roof and rib falls are the basic ground control hazards associated with underground roadways during development, stand up and, if applicable, retreat. Falls of ground can happen following the deterioration of supports or rock conditions over time, and particularly as a consequence of continuing rock deformation and/ or failure to install adequate support. Once developed, the risk of a failure is increased due to the effects of time as well as to front abutment stresses through retreat mining. The measurement of strata displacement using monitoring equipment is a form of ground control risk assessment. These monitoring systems are active, or ?live?, in a sense that risk is assessed real-time. However, there are circumstances in which falls of ground can occur without the prior recording of excessive movement. In addition, monitoring equipment is typically placed at set intervals, and strata conditions could vary between these points. Consequently, a visual assessment of other factors contributing to the risk of a fall should be made in order to complete a ground control risk assessment. Such surveys are usually one-off, thus capturing roadway conditions at one particular point in time. Ongoing deterioration is not documented through such one-time surveys, and there is a requirement for real-time or live assessment where a system is in place so that observation data can be updated on an ongoing basis, and a useful summary of prevailing roadway states produced on demand. To address the shortfalls of one-time assessments, a ?live? computerbased quantitative ground control risk assessment process has been developed. It combines visual observations processed in a quantitative manner with existing monitoring data into an interpretable output which indicates zones of roadway where there is an increased risk of a fall of ground from the roof or sides, so that remedial action can be carried out to mitigate that risk. Through improved procedures, it is now possible to generate a ground control risk assessment for each roadway, and one which can be updated frequently. This paper aims to outline and describe the assessment process.

Jan 1, 2012

Abrasivity and wear resistance are not intrinsic properties of materials, but rather parameters describing the interaction between the wear part and the material exerting the wearing action. Moreover, wear or, at least, that part of the wear which is due to the cumulative effect of minute scratches, is linked to the hardness disparity concept. Abrasivity, in this context, is a relative concept, pertaining to a metal-rock pair, rather than to a rock. Based on this assumption, a methodology has been developed and checked against actual cases, enabling description of the abrasiveness of a rock or the abrasion resistance of a metal through the ratio of comparable quantitative indicators. The paper describes the methods and provides examples of applications to practical cases (namely: rock cutting, excavation by means of tunnel boring machines (TBMs), rock crushing, and hydro-mill cutting).

Jan 1, 2012

By Takashi Yoshida

"This paper will discuss the recent situation and future of the zinc industry from the technical point of view. It includes recent problems faced by the zinc industry and technological developments. One of the biggest problems of the zinc industry is raw materials. Traditional zinc concentrate becomes much complicated with respect to its chemical and physical properties. Thus, each process faced various problems. Also, secondary resources, generating so called recycling processes, become much more important. Recycling is, of course, a very important aspect for sustainable development of society. Secondary raw material also includes a great variety of impurities not included or very low levels in traditional zinc concentrate. Some problems are caused by these impurities. To overcome these problems some technological challenges have been taking place. Details will be discussed in the symposium.IntroductionZinc is a very useful metal based on its elechtro-chemical, chemical and physical properties. The most important usage is galvernizing of steel which is used for automobile, construction and a very wide range of other indutries. Also, zinc is used for dicasting and other alloys such as brass. Smelting of zinc is different from other metal because of its electro-chemical properties. Many parameters should be controled compared with other metals such as iron and copper. Typical zinc smelting processes are the Imperial Smelting Process (ISP) and the electlolytic process. The ISP process is a pyro-metallurgical process using a blast furnace. The electrolytic process is a hydrometallurgical process. Both processes are energy intensive, and the smelting process cost is increasing because of higher energy costs. The situation of the ISP is very severe because of higher coke prices. Recently, many ISP plants have been shut down because of economic reasons"

Jan 1, 2012

By C. J. Pretorius

More than 30 percent of the global demand for zircon (ZrSi04) is supplied by South Africa. A significant amount of the zircon is exported, and beneficiated products are then imported for industrial applications locally. Beneficiating the zircon locally could have a positive impact on the local market, since zircon is only one of many such cases. Ammonium acid fluoride serves as an alternative anhydrous fluorinating agent for zircon in the synthesis of several metal fluorides1,2. It provides an effective dry fluorinating method and is easier to handle than hydrogen fluoride or fluorine gas. Zircon exposed to extreme plasma temperatures dissociates and becomes more reactive. The reaction of the plasma-dissociated zircon (Zr02.SiO2) with the ammonium acid fluoride (NH4F.XHF, where x= 1 to 5) forms two main intermediate compounds (NH4)3ZrFr(s) and (NH4) 2SiF6(s), the latter decomposing to form volatile products at relatively low temperatures, providing easy separation of the silicon and zirconium compounds. The ammonium zirconate compound decomposes to form zirconium tetrafluoride (ZrF4), which can be further manufactured into zirconium metal, to name but one product. Data on the kinetics of the reaction of ammonium acid fluoride with zircon and plasma-dissociated zircon, combined with the thermo¬dynamic parameters of the reaction, is essential for the development of an industrial process for the production of a precursor for the manufacturing of zirconium metal, namely anhydrous ZrF4. Both the reaction kinetics and reaction parameters will be included in this study, as well as some proof that the reaction proceeds to ZrF4 on a small batch scale. If the exact reaction parameters can be pinned down, a wide spectrum of anhydrous metal fluorides can be synthesized through this fluorination route.

Jan 1, 2012