Search Documents

By Joe McQuerrey, William Kendall, Gene Wilson

"Roof bolting is the standard for ground control in underground coal mining. Rib and truss bolting is just as important when conditions are less than desirable. As a manufacturer of roof drills, J.H. Fletcher & Co. (""Fletcher"") promotes a walkthrough design machine to protect the machine operators from rib hazards.When installing rib and brow bolts in high mined heights, the operator's natural desire is to step from under the canopy onto the drill feed mechanism. This is done to allow a better reach to the drilled hole in the rib or brow. This, of course, is not an approved or acceptable practice.The effort to improve the operators' ability to reach the rib and brow has resulted in a new boom design. The design was first shown in September 2008 at the MINExpo in Las Vegas, NV. The design incorporates a step out area towards the rib side of the machine. The step provides improved access to the mine rib and brow.Having a solid concept does not guarantee an accepted design. Operator acceptance is the goal. When the machine was first tried in the underground environment, the machine operators did exactly as requested: run the machine as supplied and suggest improvements.In the fast pace job of roof bolting, any ergonomic improvements are welcome. These improvements usually increase the operator's productivity and safety. Based on operator feedback and final evaluation with Fletcher, machine revisions were generated. When the machine revisions were completed, Fletcher again asked the operators for comments, giving the boom design an evolving path into our industry.INTRODUCTIONIt's human nature to find the most comfortable position in which to do a task, especially for repetitive tasks. Designing a machine that will withstand the rigors of underground mining is a challenge in itself. With stringent safety requirements and limited real estate, there is a constant evolution in design to converge safety with productivity. With the ongoing development of the ""Rib Access Boom,"" one more step in the evolution process has been taken."

Jan 1, 2010

By Felipe Perissé Duarte Lopes

The tensile properties of DGEBA/TETA epoxy matrix composites reinforced with different amounts of curaua fibers were evaluated. Tensile specimens with up to 35% in volume of long, continuous and aligned curaua fibers were room temperature tested in an Instron machine. The fracture was analyzed by SEM. The results showed significant changes in the mechanical properties with the amount of curaua fibers. This was compared to other bend-tested composites with distinct matrices. The fracture analysis revealed a weak fiber/matrix interface, which could be responsible for the comparatively low performance of some properties.

Jan 1, 2010

By M. K. Ameen, R. El-Hacha

This paper presents the analytical results obtained from numerical simulation of reinforced concrete slabs strengthened with various FRP systems and subjected to blast loading. A three-dimensional finite element model using AUTODYN software was used to predict the overall behavior of the slabs. The numerical results were validated by comparing with experimental results from a program carried out to investigate the efficiency of different strengthening systems on the blast resistance improvement of small-scale reinforced concrete (RC) slabs. The experimental program consisted of testing nine RC slabs strengthened with three different externally bonded (EB) FRP systems attached at the bottom side of the slabs and one RC slab tested without strengthening for comparison purposes. The EB FRP strengthening systems investigated included two layers of Carbon Fiber Reinforced Polymer (CFRP) sheets, two layers of Glass Fiber Reinforced Polymer (GFRP) sheets, and one layer of Glass-Fiber Resin Polymer (GRP) sheet. Different epoxy resin, patching mortars and impregnating epoxy adhesives were used for the slab surface preparation and FRP system application of the strengthening layers. The aim was to evaluate the residual strength of the test specimens after exposure to blast loads. The blast loading parameters were evaluated for each test using AUTODYN simulation and compared with the computer program CONWEP. All specimens were subjected to same spherical TNT charge weight and stand-off distance with the respect to the slab top surface. Extensive comparison is made between the experimental results and the AUTODYN simulations for the control unstrengthened slab and the strengthened slabs including time history records of the bottom steel strain and mid-span acceleration and the peak dynamic deflection of the slabs.

Jan 1, 2010

By Melinda Channel, Alan W. Weimer, Jonathan R. Scheffe

"There is a need to develop cost effective renewable energy processes for the production of clean fuels that can simultaneously mitigate the U.S. energy/global environmental security issue. If H2 can be obtained cost effectively via the splitting of water using concentrated sunlight, then it’s possible to operate a fuel cell using renewable H2 or to synthesize other fuels based on renewable H2 for generating electricity or for running internal combustion engines. For example, H2 can be reacted with sequestered carbon dioxide (CO2) to produce syngas (H2/CO) via reverse water gas shift (RWGS), i.e. H2 + CO2 ? CO + H2O. The syngas can be catalytically methanated to form synthetic natural gas (SNG) or it can be catalytically reformed to produce liquid fuels such as “green” gasoline via the MTG process (syngas? methanol ? gasoline). The desert SW United States is home to world class sunlight. Fundamental ferrite thermodynamics will be reviewed, an example of the beneficial effect of ferrite surface area on reaction kinetics will shown, and process economics will be investigated for a 100,000 kg/day facility to produce H2.Introduction and Background ThermodynamicsSpinel ferrites of the form MxFe3-xO4, where M generally represents Ni, Zn, Co, Mn, or other transition metals, have been shown to be capable of splitting water according to the two step cycle shown below:MxFe3-xO4 + solar thermal energy ? xMO + (3-x)FeO + 0.5 O2 (1)xMO + (3-x)FeO + H2O ? MxFe3-xO4 + 2H2 (2)This is an inherently clean and sustainable process, as the only net inputs are solar energy and water, and the net outputs are hydrogen and oxygen. Ferrite water splitting cycles are advantages compared to other high temperature water splitting cycles, such as the ZnO/Zn and Mn2O3/MnO cycles, because thermal reduction has been demonstrated at significantly lower temperatures[1, 2]. As a result, overall efficiency may be increased due to the fact that radiation losses increase as the fourth power of temperature, and material considerations for reactor design should be more flexible. Additionally, cycle repeatability has been demonstrated with relative ease as compared to other thermochemical cycles [3-6]. However, the amount of hydrogen per mole that is generated is significantly less than for other high temperature thermochemical cycles due to the fact that only Fe3+ is capable of being reduced at the temperatures of interest[6]. In addition, water oxidation kinetics appear to be very slow, likely due to diffusion or surface area limitations created by near surface oxidation [6, 7]."

Jan 1, 2010

By Nadia C. Miller

In situ stope leaching is an innovative mining system that reduces the surface impacts of conventional underground mining. As in any leaching operation, stope leaching requires hydrologic site characterization and control of leaching solutions. Several tracer tests, using sodium chloride (NaCl) in various concentrations, were conducted by the U.S. Bureau of Mines (USBM) in an underground experimental stope to simulate a leaching environment. The tests were conducted in fractured crystalline rock that was partially water-saturated. As tests progressed, the surrounding fractures became more saturated. A predominant flow direction away from the stope was found during testing. Testing procedures, results, and a remediation plan for in situ leaching based on field observations are presented in this report.

Jan 1, 2010

By B. P. Sereda

The properties, characteristics and phase structure of chamotte refractories produced with the usage of mullitecorund chamotte and caoline have been given. The comparison of new refractory C-45 obtained by us and refractory C-43 produced by traditional method has done. The physical-chemical properties of refractories is reviewed. The visual porosity, density and pore characteristics of given refractories was calculated. It is established that C-45 has the less gas permeability then C-45 that gives melting units more stability. The petrographical microstructures of refractories have been done. The main phase structures and their influence on refractories properties have been observed. It is established that refractories with mullitecorund chamotte adition has more advantages then refractories gained by traditional method and can be applied to melting units.

Jan 1, 2010

By Yasuhiro Aoki, Akihiro Sato, Mikiya Arai

In this study, a freckle formation model based on the Rayleigh number was applied to actual multi-component Ni-base single crystal superalloys and verified in large scale casting trials. Finally, new Ni-base SC superalloys having a balance between castability and creep strength has been developed.

Jan 1, 2010

By Robert J. Timko

This U.S. Bureau of Mines study examined spontaneous heating episodes in coal mine pillars in an active underground coal mine. The information obtained from these incidents was then analyzed to learn which sampling methods provided the earliest indication of pillar heating. The objective of this study was to discover if the location of future events of pillar spontaneous heating could be inferred from the available information. The spontaneous heating-prone area in this evaluation involved pillars located just inby the mine portals. Several detection methods were used to determine gas levels outside as well as inside the affected pillars. It was hoped that, by incorporating external and internal sampling methods into an organized pro-gram, locations undergoing spontaneous heating could be determined more readily. This study found that by drilling small-diameter boreholes into the pillars, then obtaining gas samples from the affected pillars, the ability to locate early spontaneous heating episodes was improved. However, the ability to accurately predict future spontaneous heating events remains in question.

Jan 1, 2010

By R. Therrien, L. Gosselin, J. Raymond

ABSTRACT: The ground-source heat pump is a low-carbon technology that uses the earth’s renewable geothermal energy to heat and cool buildings, with an ef?ciency 3 to 4.5 times that of conventional systems. These high performances are achieved by exchanging heat with the earth using a ?uid that is groundwater, surface water or closed loop water. Expensive installations, such as water wells or buriedcoils, are however necessary to transport the ?uid in and out of the earth, making ground-source heat pumps more costly than conventional systems. Installation costs can be reduced in mining environments due to the abundance and the accessibility of resources to be used with heat pumps. Examples of system design calculations using data from the Mouska and Doyon mines in Abitibi show signi?cant installation cost savings using dewatering mine water or ground heat exchangers installed below oxidizing waste rocks. Ground-source heat pump technology is reviewed and scoping calculations are presented to illustrate how such systems can be installed in mining environments.

Jan 1, 2010

By S. D. Viljoen

The use of ceramics to protect equipment subjected to wear in abrasive and corrosive applications has been accepted by most plants as the industry norm. Little is, however, known about alternative special ceramic based products which are available for the protection of plant assets. With careful engineering, impact resistant ceramics can be used in high impact zones using modern ceramic technology. Properly selected and properly installed, ceramics will provide a tough wear resistant lining for protection against abrasion and impact. Basalt, on the other hand, is widely used in coal washing plant process pipes with varying degrees of success. Basalt is normally not used for the lining of bends, ?T? pieces or reducers due to the reduced wear resistance compared to alumina ceramic. The advantage is a much reduced initial capital cost. A patented ceramic composite non-return valve solved an old problem encountered in the operation of medium sumps. The design approach overcomes the lack of functionality of alternative designs and reduces valve wear while preventing medium settlement during plant shutdown periods. Direct bonded ceramic pulley lagging is becoming the industry norm, eliminating most of the problems encountered with conventional pulley lagging systems.

Jan 1, 2010

By W. Lum

In the U.S., flexible metal pipe culverts are designed by ring compression theory because the pipes are capable of deflecting and deriving side support from surrounding ground. For economy, tunnel liners are often designed as flexible structures that depend on the lateral pressure of the surrounding ground to maintain stability. In this paper, simple formulas are presented to determine the maximum deflection a concrete tunnel liner may assume and the ring compressive strength of the deflected liner. A tunnel can then be constructed to work within these limits. Similar techniques may be used to design concrete pipes.

Jan 1, 2010

By John C. Edwards

Carbon monoxide (CO) sensors are used in mine fire early-warning systems. Experiments were conducted by the U.S. Bureau of Mines with six diffusion-type CO sensors to determine their response to a reference CO concentration under both static and dynamic flow conditions. Static experiments were conducted with 0.5 L/min flow of 16 ppm CO in N2 through 8-and 12-L chambers. Dynamic flow experiments were conducted in two environmental chambers: One had directional flow capability of 1 m/s, and the second provided moderately nondirectional flow as high as 1.8 m/s. Reference CO concentrations of 13.5 to 19 ppm in air were used for the dynamic experiments. The results of the static experiments demonstrated that the sensors consistently underestimated the reference gas concentration. The dynamic experiment results showed the sensors provided reasonable agreement with the reference gas concentration when directional flow effects were not considered. Directional flow effects were evaluated for two sensors. One of the sensors showed a strong dependence upon the relative orientation of the diffusion tube with respect to flow direction. The second sensor did not show a dependence upon flow direction. The sensors' directional flow effect is significant for their proper in-mine utilization.

Jan 1, 2010

By Neo Molelekeng, Jocelyn Bouchard, Rebecca Monnapula, Martin Émond

"Xstrata Alloys – Eland Platinum concentrator (South Africa) has recently been commissioned and is now initiating a challenging optimisation program encompassing the entire operation. Process control improvements are key elements of the program and initial results have demonstrated how leveraging from current assets can bring significant improvements through overall reduction of variability. This paper gives a brief overview of the operations and details how Eland is striving to become a top tier leader with advanced regulatory control strategies recently implemented. Results reveal that what can be achieved in a standard control system (PLC or DCS) should not be underestimated as the first interventions led to a steadier operation of the primary ball mill circuit. Following the improvements, significant and sustained reductions of standard variation were observed for key process variables around their set-point: primary ball mill feed rate (72 %), rougher feed density (58 %), and rougher feed flow rate (47 %). A path forward has been identified to tackle further opportunities around the primary grinding circuit: water balance management, throughput optimisation as well as charge and power draw control.INTRODUCTIONThere are numerous approaches to mineral processing plant optimisation. As the benefits of determining the right reagent types, mix, dosage and addition points, or the proper charge of grinding media in a mill are fully appreciated, there is still nowadays some misunderstanding and misconceptions about process control in general and how it can contribute to the whole optimisation process. The confusion between the various disciplines involved, i.e. instrumentation, control system programming, automation and process control, certainly does not serve the best interest of the industry with this regard."

Jan 1, 2010

By P. J. Nicholson

The methods of reinforcement to be discussed in this paper are all insitu methods, ones that can be used on the soil structure as it exists in the ground, and do not rely on excavation and replacement of the soil. Current practice in the United States, as well as new ideas and methods, will be discussed as they relate to slope stability, retaining walls, and to other uses such as control of mine or cavity related subsidence and to liquefaction control under existing structures. The method is based on the concept of "nailing" or reinforcing the soil in place, and thereby causing a mass of soil to act as a coherent unit. When performed properly, a true gravity structure can be constructed, one that will remain intact under both horizontal and vertical loadings and that will also resist vibrational and seismic loadings.

Jan 1, 2010

By Michael Milstein

Northwest Research Station said as more and more older dams are removed to benefit fish, it’s become clearer that rivers rework themselves quickly.“Where the dam is relatively small, it’s a quick response,” he said. “The river quickly forgets.”

Jan 1, 2010

By M. Solomon

Crushers are designed and manufactured to survive the severe duty of mining environments worldwide. Under these conditions the crusher performance and availability is one of the critical factors in the mine?s production and profitability. Traditionally the development of these machines tends to be experience-based, incremental improvements in design due to challenges of different applications, duty, or manufacturing. In order to better serve the mining industry a new approach was taken to the design of primary crushers. This approach was to focus on safety and maintenance activities. The result of this effort is a new generation of gyratory crushers that can be serviced from above. Using the features of this new generation of crushers to their fullest extent crushing installations have improved safety, reduced design and construction costs, and lowered maintenance requirements. This presentation explores the benefits of two crusher installations utilizing top service crushers.

Jan 1, 2010

By U. Steiner

Electronic detonators have been in commercial use for a decade, with an excellent safety record. This paper lists known incidents involving electronic detonators. Typical standards required by regulatory bodies for static electricity and electromagnetic fields are reviewed. The performance of some detonators is compared to these standards; in general the minimum standards are easily exceeded. The general resistance of electronic detonators to extraneous electrical energy that can be derived from the body of test results is compared to danger levels for exposure of humans to these energies; it is shown that electronic detonators can safely tolerate higher electrical energies than people can. This comparison includes comparable data for electric detonators, which are shown to be more vulnerable to extraneous electrical energy than people are. Electronic detonators also bring significant safety benefits in blasting due to their testability, two-way communications, reliability, programmability and precision. The links between these attributes and enhanced safety are discussed with examples from actual blasting. Although electronic detonators are usually more vulnerable to extraneous electricity than non-electric initiation systems, the paper shows that the net safety benefit in handling and blasting is in favor of electronic detonators, which are the safest initiation system that has ever been offered to the mining industry.

Jan 1, 2010

By G. X. Zeng

A calculation programme of finite element method has been developed in order to study the behavior of excavation with sheet piling in soft clay. Based on a series of isotropically consolidated-undrained tests (CIU) on Hangzhou clay a linear relationship between the normalized initial tangent modulus number, E1, and stress-path parameter, a, is found for four different stress paths, and stress-path dependent modulus equations derived. Meanwhile, several influence factors, such as embedment depth and stiffness of the wall and soil conditions, were taken into consideration in the programme. Some valuable conclusions were obtained. Finally, a case history was studied by the proposed method of calculation. The result of calculation and the field observation are in good agreement.

Jan 1, 2010

By Yongbin Yang

Cathodic reduction of oxygen is a process involved in many fields. As is well known, the mechanism of oxygen reduction usually varies considerably with electrode substrates. In this paper, cathodic reduction of oxygen on gold electrode was studied by linear sweep voltammetry with regards to cyanide leaching of gold. As the results shows, the electron transfer number increases as potential shifted negatively and decreases as pH value increases. Besides, the increment of electron transfer number as a function of potential decreases when pH value increases. When pH increases to 13.0, the volt-ampere curve exhibits a relative flat section with currents approximate to the limit current density of a 2e process. By varying dissolved oxygen concentration, the electron transfer number was calculated for pH11.0 at different potentials, the results being 2.387e, 2.732e, 2.982e, and 3.227e at, -0.35V, -0.40V, -0.45V, and 0.50V, respectively. The calculated current densities are in good conformity with measured results.

Jan 1, 2010

By Takashi Sasaoka, Pinyo Meechumna, Hiroshi Takamoto, Pipat Laowattanabandit, Akihiro Hamanaka, Kikuo Matsui, Hideki Shimada

"The EGAT Mae Moh coal mine is an open-cut coal mine in Thailand that produces about 16 million tons of lignite annually to generate 2,400 mw of electricity. The surface mine pit covers is 4 by 7 km (2 by 4 mi) with mining depths ranging up to 260 m (853 ft). A large pit slope is formed with the progression of the mining operation. However, massive slides in the pit slope often occur due to weak planes, such as faults and bedding, and the weak mechanical properties of the rocks. Hence, a 200-300 m (656-984 ft) boundaries of rock block including coal seams is left in front of faults in order to prevent slides and maintain the stability of the pit slope. As a result, there are significant coal reserves beneath the abandoned area along the pit slope.The focus of this paper is on the applicability and design of the highwall mining for recovering much of the coal left along the pit slope.INTRODUCTIONThe EGAT Mae Moh Mine is located about 630 km (186 mi) north of Bangkok, Thailand (see Figure 1). It is the largest coal mine in Thailand and produces about 16 million tons of lignite annually from open-cut mining (70 % of the total coal produced in Thailand). The coal is used to generate 2,400 mw of electricity at the Mae Moh power plant, which is situated near the mining area. The mine pit covers an area of 4 by 7 km (2 by 4 mi) at varied depths up to 260 m (583 ft) as shown in Figure 2. As the mining operation progresses, the pit becomes to be deeper and deeper. In the year 2035, the bottom of the pit is expected to reach depths of 500-600 m and the open-cut mining operation will be finished. The possibility of an underground mining operation is being investigated.A large pit slope is formed with the progression of open-cut mining. However, massive slides often occur in the pit slope along weak planes including faults and bedding planes due to the weak nature of the rock. As a result, 200 to 300 m (656 to 984 ft) boundaries of rock including coal seams are left in place in front of faults to prevent slides and to maintain the stability of pit slope. Moreover, the dip of the slope is less than that of the planned design. As a result, there significant coal reserves abandoned along the pit slope."

Jan 1, 2010