Search Documents

By Anil K. Ray

Roof falls are one of the greatest hazards in underground coal mines worldwide. Due to stringent safety measures and extensive support system development, roof falls have been reduced significantly but they still persist in many underground coal mines. Some of the roof falls initiate with cutter roof or guttering. In the past, many factors have been identified as being responsible for the development of cutters and roof fall. These responsible factors can be broadly classified as stress related or non-stress related. In this paper the finer details of mining technique have been taken into consideration for better understanding of cutter roof and roof fall problems. Three dimensional finite difference modeling has been used to explain the mechanism of cutter development. Strain softening material behavior has been used to realistically simulate the cutter formation, and common cutting sequences as implemented in the field have been simulated. This was done with an objective to determine whether the cutting sequence has really any significant control over cutter formation or not. In addition to cutting sequences, the effect of cut length is also studied. The effect of step cutting and turning of crosscut into and away from major and minor horizontal stresses is also examined to see its influence on cutter development.

Jan 1, 2009

By M. Pawlik, E. Arinaitwe, V. Ferrera

A series of flocculation tests were performed on dilute quartz suspensions with the use of five polyacrylamide-based flocculants of similar molecular weights but of different degrees of anionicity. The tests were performed as a function of ionic strength and pH. The macromolecular conformation of flocculants in solution was assessed through intrinsic viscosity measurements under the same physicochemical conditions as those of the flocculation tests. It was generally found that the flocculating efficiency of the polyacrylamides correlated with their ability to coil or stretch in solution. Polyacrylamides with the degrees of anionicity on the order of 10-18% showed the highest flocculating efficiency in terms of the settling rates of the flocculated solids and the residual turbidity of the resulting supernatant. At the same time, these most effective flocculants were also found to exhibit the greatest tendency to coil and stretch in solution. This result suggests that the flocculating power of a flocculant is determined not only by its ability to adsorb onto (and bridge) fine particles but also on its ability to conform to the size of the resulting floes.

Jan 1, 2009

By Eric Grigoryan, Wade Hutchison

An engineering study of 2,250 blasting damage claims from 1999 to 2008 in Tennessee, Kentucky, Virginia, Nevada, California, Georgia, South Carolina, North Carolina, Alabama, Arizona and Utah were investigated over the last decade and these investigations determine that blasting ground vibrations damage claims are valid less than 1.3 percent of the time. This study determined that valid blasting damage occurred as a result of impact damage associated with fly rock, air concussion stressing, instantaneous reverse stressing associated with ground vibration and crater zone soil shifting related stressing.

Jan 1, 2009

The global mining industry is perceived to be a world leader in sustainability reporting û with a 2008 Ernst & Young survey placing four mining companies in their top five performers in sustainability reporting in South Africa. There is certainly good evidence to support this finding, but there remain many ongoing issues with respect to sustainability reporting and some important areas for improvement by mining companies globally. This paper begins with a broad (but brief) review of sustainability and the technical basis for reporting against a wide range of typical indicators or measures on the environmental aspects of mining. The various protocols, frameworks or systems are then reviewed, with a particular focus on the Global Reporting Initiative (GRI) and its associated mining sector supplement (including the evolution from environmental to sustainability reporting). A wide-ranging survey of reporting by mining companies is presented, including detailed analysis of 2007 and some commodity sectors over time. Examples of reported data are synthesised and analysed, focusing on their accuracy, consistency and utility for accurate assessment of the life cycle impacts for minerals and metals. A number of areas are identified for improved reporting by all mining companies, including water resources and consumption, energy consumption, process inputs (eg acids, solvents, etc), pollutant emissions, including greenhouse emissions, mine site data (not aggregate company totals) and finally rehabilitation and land status. Given the nature of mining, and considering parallels between æpeak oilÆ and the mining sector, it is critical that the state of sustainability reporting continue to evolve and improve û both in the number of companies using the GRI but also in the level and consistency of data being reported. Overall, the paper presents an important review of the present state of the art in sustainability reporting for mining, and provides a range of insights into ways to help improve reporting in the future for all mining companies.

Jan 1, 2009

Development of a permanent human base on the Moon for exploration requires a self sustaining system. This entails production and processing of limited amounts of raw material on the Moon. Any mining and construction activities on the Moon can only be performed by a robust excavation machine that can excavate a variety of material from loose surface regolith to consolidated (frozen) regolith with embedded rocks in the mixture. Meanwhile, limited amount of information on lunar regolith is available to develop and optimize a machine for given lunar ground conditions. Therefore, any excavator designed for use on the lunar surface should have the ability to adapt to a wide range of operating conditions. A prototype cutterhead for the lunar excavator was built and tested at the Kennametal facility in Latrobe PA A. This paper discusses the results of initial material characterization as well as full scale tests of a prototype cutterhead inrelevent material. A brief review of anticipated production rates under various assumed ground conditions will also be presented.

Jan 1, 2009

By Markku Rytkonen, Shaolong Chen, Ilpo Kylmäkorpi, Hannu Mansikkaviita

Though the Peirce Smith (P-S) converter is a traditional type of furnace, continuous improvement in its mechanical and electrical design is still Kumera's approach. Efforts are made particularly on the following aspects: converter head shape for easy fabrication and structural strengthening, oxidation air swivel joint for low pressure drop and low noise level, wind box for even air distribution to tuyeres, drive unit and its control for reliable and handy operation. These improvements have successfully been applied in recent P-S converter deliveries.

Jan 1, 2009

By D Barclay, S Mercer, S Wright

Mine water management is often an afterthought in mine planning processes and can introduce significant risks to projects when studied as a stand alone component at a later stage in the mine design. Incorporation of a mine dewatering and pore pressure dissipation strategy in the early stages of mine planning is imperative in order to minimise constraints on the production schedule, to match designed pit slopes and maximise project value for an open cut mine option such as Olympic Dam. A risk-based mine planning approach was adopted during the project selection phase study whereby water management was introduced into mine planning, scheduling and the development of an operational strategy. Hydrological and hydrogeological studies and outputs were successfully integrated into the various iterations of the mine planning cycle during early selection phase to manage the potential water management risks associated with pit slope depressurisation and access to dry working conditions during rapid advancement of mining phases.An extensive network of vibrating wire piezometer sets and long-term depressurisation testing characterised aquifer conditions and demonstrated that hydraulic connectivity exists within the geological profile due to the presence of structures and resource drill holes which enhance vertical connectivity. This connectivity, along with underdrainage from mining activities contributes up to 100 m of depressurisation in low permeability units.A pit dewatering strategy incorporates the mine planning schedules and accounts for operational constraints as to the location and development of the dewatering wells, storages and pipelines. Numerical modelling generated a range of likely pit inflows and dewatering requirements with the average initial dewatering discharge likely to be 150 L/s and reduce quickly to 50 L/s after five years, depending on the premine schedule.Coupled hydrogeological and geotechnical assessments were also carried out as part of the mine planning cycle and indicate that successful dewatering will go a long way to reduce the pore pressures within key geotechnical units during the rapid mining phase where around 300 m of cover sequence is stripped in five years. However, the residual storage in the primary aquifer and the residual pore pressure in underlying low permeability units will need to be dissipated (in-pit horizontal holes) as the pit floor advances. Pit slope design angles are sensitive to depressurisation and dewatering and up to 70 per cent depressurisation of key geotechnical rock units are required. Whilst an accelerated program of aquifer dewatering supported by lithostatic unloading should drive rapid depressurisation in the lower permeability units, intervention is anticipated in key geotechnical units such as the Tregolana Shale and volcaniclastics. The extent of induced drainage will ultimately depend in part upon the mining rate and geotechnical stability requirements. Practical operability testing addressed the potential for operational constraints to mine depressurisation activities such as congestion and mining schedule development within the pit and identified that depressurisation drilling can be achieved even with reduced access availability. Mine operations and planning groups established design criteria and considered the likely inoperable periods following rainfall events of seven to 14 days to manage the base surge and minimise impact on production. In-pit surface water management options to minimise operational disruptions during and after significant rainfall events were estimated used a stochastic approach.

Jan 1, 2009

By M Denton, M Rheinlander, S Mundell, M Broadgate

The manufacturing industry reinvented its approach to the manufacturing process by managing and measuring it end-to-end. This improved returns on production assets, improved information quality and reduced delivery time, resulting in larger net profits through cost reduction and improved cash flow. Today this approach is standard in the manufacturing industry. Resource development has many requirements in common with the manufacturing production line. These include: control of the various steps, transparency of the state of the process to various levels of the organisation and the overall efficiency with which the process is executed. The authors argue that the introduction of manufacturing execution systems (MES) concepts and technologies to resource development processes will lead to similar improvements in control, transparency and efficiency and could improve profitability and enable staff to work more effectively and make better decisions.

Jan 1, 2009

By R. L. Castro

Block caving methods, when operated under favourable rock mass conditions, can achieve higher production rates and lower operating costs than other various existing underground mining applications. For this reason, it has been considered the preferred method for the mining of deep and large orebodies in current and future operations around the world. One of the key aspects in the design of block caves is the selection of the production level layout, which, among other parameters, is based on the gravity flow characteristics of the caved rock. This is because gravity flow has a large impact on total ore recovery and the amount of dilution in a caving operation. Today, there are a number of computer based methods which aim to emulate the gravity flow pattern of the caved rock. In this paper, the authors present the development of FlowSiman improved model of gravity flow based on the cellular automaton approach, to estimate dilution entry, mixing and ore recovery. As part of the model development, flow simulations were conducted and subsequently compared to full-scale data collected at two mine sectors operated by Codelco Chile. The results indicate that by using proper calibrated parameters, good correlations between simulated and measured grades as well as dilution entry are obtained. The potential use of the numerical tool to evaluate drawpoint spacing in terms of recovery and dilution for block/panel caving operations is also presented.

Jan 1, 2009

By A. D. S. Gillies

Inertisation is used to enhance the safety of underground mine areas either to avoid the potential for a combustion event or to stabilize a situation after an ignition, fire or heating. The primary objective of a recently completed Australian Coal Association Research Program (ACARP) study was to review coal mine inertisation and in particular to focus on use of the Polish mine fire simulation software Ventgraph to gain better understanding of how various inertisation units interact with the complex ventilation behavior underground during a substantial fire. Critical aspects targeted for examination under the project grant included location of the unit for high priority fire positions, size of borehole or pipe range required, time required for inertisation output to interact with and extinguish a fire, effects of seam gases on fire behavior with inertisation present and main fan management. A major accomplishment of the project has been to take findings from the simulation exercises to develop inertisation related modifications to the Ventgraph fire simulation program in conjunction with the Polish program authors. Selected mines were ?evaluated or audited?as to the ability to deliver inert gases generated from GAG units to high priority underground fire locations .A coding system has been developed and many potential underground mine fire sources cannot be successfully inertized with the GAG docked at the current specified point; this is particularly so for fires in extended areas of workings or in panels. There is a limit to the ability of the GAG jet engine to deliver exhaust down smaller dimension borehole. There is a need to examine the use of the GAG for production or proactive uses in a wider application in Australian mines responding to recovering from mine fires, spontaneous combustion heating?s, elimination of the potential explosibility of newly sealed gobs or inert mines or mine sections on closure. Some of the current uses of low flow inertisation facilities could be more effectively undertaken with the GAG unit.

Jan 1, 2009

By J. M. Gregg, C. J. Persellin, I. D. Somerville, E. A. Atekwana, K. L. Shelton

"Zn-Pb sulfide mineralization at Abbeytown mine and Twigspark quarry comprise the only known car¬bonate-hosted base metal sulfide deposits in the Sligo syncline, northwest Ireland. Limestone sedimentation occurred uniformly throughout the region during the Early Carboniferous (Mississippian) as observed by field relationships and lithofacies; however, petrographic and stable isotope evidence indicate that host-rock dolomitization occurred under different conditions at localities to the west and east of the Ox Mountains inlier, suggesting significant uplift and geologic isolation of these areas prior to dolomitization. Localized fluid flow systems are thought to be responsible for sulfide mineralization and associated epigenetic carbonate cements. West of the Ox Mountains inlier at Abbeytown, evidence of three geochemically distinct fluids are observed: (1) a lower-temperature, lower-salinity fluid (70°-130-°C, 4-9 wt.% equiv. NaCl); (2) a lower-temperature, higher-salinity fluid (70°-140°C, 15-24 wt.% equiv. NaCl); and (3) a higher-temperature, moderate-salinity fluid (165°-220°C, 8-14 wt.% equiv. NaCl). Similar fluid types were observed at the Twigspark deposit. The source of the higher-salinity fluid is likely seawater evaporated to near the point of halite precipitation. The higher-temperature fluid is thought to have been derived from deep circulation of basinal brines. It is speculated that mixing of the higher-salinity fluid with the high-temperature fluid was vital for ore formation at Abbeytown because fluid inclusions in sphalerite have homogenization temperatures and salinity values that fall along a mixing trajectory of these end member fluids. Also, areas where the high-salinity end member fluid is absent are barren of sulfides. Less complex fluid systems are indicated for sites east of the Ox Mountains inlier where no sulfide mineralization was observed. Data from base metal sulfide prospects in northwest Ireland indicate no connection with the regionally extensive flow system thought to be responsible for Zn-Pb deposits throughout the Irish Midlands.Les minéralisations en sulfures de Zn-Pb de la mine Abbeytown et de la carrière Twigspark sont les seules gîtes de métaux usuels à encaissant carbonaté connus dans le synclinal de Sligo, au nord-ouest de l’Irlande. Ces carbonates se sont déposés d’une manière uniforme dans la région au Carbonifère inférieur (Mississippien) tel que l’indiquent les relations de terrain et les lithofaçiès; les données pétrographiques et d’isotopes stables indiquent toutefois que la dolomitisation de l’encaissant s’est faite sous des conditions différentes aux localités situées à l’ouest ou à l’est de la boutonnière des Ox Mountains, ce qui suggère un soulèvement et une isolation géologique significative de ces secteurs avant la dolomitisation. L’action de systèmes de circulation locaux sont considérés être à l’origine de la minéralisation sulfurée et des ciments carbonatés épigénétiques qui leur sont associés. À Abbeytown, à l’ouest de la boutonnière des Ox Mountains, on note les effets de trois fluides géochimiquement distincts: (1) un fluide à basse température peu salin (70°-130°C, 4-9% poids équivalent NaCl); (2) un fluide à basse température fortement salin (70°-140°C, 15-24% poids équivalent NaCl); and (3) un fluide formé à plus haute température et salinité modérée (165°-220°C, 8-14% poids équivalent NaCl). Des fluides similaires ont été observés au gîte Twigspark. La source présumée du fluide le plus salin est de l’eau de mer amenée par évaporation près du point de précipitation de la halite. Le fluide à plus haute température est probablement dérivé de la circulation profonde de saumures dérivées d’un bas¬sin sédimentaire. Il est possible que le mélange du fluide à haute salinité avec celui à haute température ait joué un rôle central dans la genèse de la minéralisation d’Abbeytown parce que les températures d’homogénéisation et les valeurs de salinité des inclusions fluide"

Jan 1, 2009

Downhole survey uncertainties observed at various De Beers operations prompted an investigation into their possible effect on deposit shape and volume. An accurately surveyed artificial æboreholeÆ was constructed and different downhole survey instruments tested. In this way an empirically determined error range of 0.1 per cent to ten per cent was derived for downhole survey data. These survey errors were applied to an orebody model at an existing mine. Visualising the sphere of uncertainty associated with a borehole trace using a general mining package (GMP) gives an indication of possible volume variance. The resulting orebody maximum and minimum volume scenarios for three different depths (200 m, 500 m and 800 m) are presented. For certain instruments and borehole angles, the 3D positional error can be as high as 100 m at 1000 m down the hole. At depths below 200 m the resulting volume deviations can become significant for borehole survey errors exceeding 0.35 per cent. At 800 m depth the volume difference can approach 25 per cent. These figures assume that the error is compounded. The impact of these downhole survey errors is greatest for pipe-like orebodies such as porphyries and kimberlite pipes. Subhorizontal sill-like orebodies (and coal seams) will not be significantly affected by these errors. The impact of this type of survey error needs to be stated (and quantified) and is significant in JORC classification.

Jan 1, 2009

By Unknown

ATF has provided a Guide to Recording Suspicious Persons Description in the Safety & Security Brochure. This guide may be useful for recording descriptive information on any suspicious individual. Suspicious activities can be reported to ATF’s 24-hour hotline listed in the front of the Guide or to your local law enforcement authority.

Jan 1, 2009

By Nan Wang

Based on the commercial computational fluid dynamics software, Fluent, the fluid flow and temperature field in an iron-bath reactor were simulated numerically, and the effects of top-blown and side-blown operating parameters on the mixing time of iron bath, distribution range of oxygen in top space, and post-combustion ratio were investigated. The simulated results showed that the mixing time of iron bath increased initially and then decreased with the increase of inclined degree and immersion depth of side-blown lance. The distribution range of oxygen became wider as pulling the top lance away from the iron bath. Furthermore, post-combustion ratio was reduced given the top lance was too close the bath. The simulation results provide theoretical base for the process optimization of iron-bath reactor and further development of new type iron-bath smelting reduction process.

Jan 1, 2009

By A. C. Legg

BCL Limited operates a nickel-copper flash smelting operation at Selebi-Phikwe, situated in north-eastern Botswana. The original furnace was commissioned in 1973 and produces a high grade sulphide matte, from its own concentrates plus additional custom feeds, which is shipped to refineries in Zimbabwe and Norway for further processing. In 2004 the company embarked on a study to modernize the flash smelting complex, with an emphasis on extending campaign life, improving the furnace integrity and enhancing throughput and process efficiency. First phase initiatives from this exercise, including the fundamental switch to a single concentrate burner operation of the flash smelting furnace, were implemented in July 2007. This paper summarizes experiences prior to implementation, details the specific improvements made to the flash smelting furnace and associated operations, highlights the improved plant performance after modernization, and outlines second phase expansion plans that are currently under consideration.

Jan 1, 2009

By J. M. Simard, S. Morissette, P. Coursol, P. Mackey

A new, powerful model is presented that focuses on plant logistics and scheduling aspects of the smelting, converting, fire refining and casting operations at the Horne smelter. This plant complex is the largest custom copper smelter in North America. It handles a wide range of feeds and utilizes a number of proprietary continuous and batch technologies that require good scheduling in order to maximize plant capacity and efficiency. The present model was developed by Xstrata Process Support, in collaboration with the Horne smelter, and uses the Arena® software to evaluate the impact of a number of plant variables on the annual copper capacity of the plant. Model development was carried out by Xstrata Process Support, in collaboration with the Horne smelter, through the effective combination of process chemistry knowledge and detailed knowledge of the plant operation (including all material flows and transfers, as well as information such as operating on-line times, plant stoppages and also scheduled and unscheduled maintenance activities). A number of case studies were then examined, including the impact of anode furnace and casting cycle times on annual copper capacity and the impact of a one-crane mode of operation in the converter aisle, which normally operates with two cranes in service. The model predictions were found to match actual plant results very well. The present modelling of plant logistics and the scheduling aspects were found to add important dimensions at the plant with regard to projections of the real-life plant capacity. As demonstrated in the present case, this type of model and application can have a significant impact on optimizing operations at a given plant. This impact is particularly important in the current market environment, where emphasis is on maximizing plant output and lowering costs. These models can help yield the easily obtained gains that are clearly desirable in these times. Xstrata Process Support has developed Arena models for other operations and is available to explore new applications for a win-win situation at other plants, including mines and concentrator operations.

Jan 1, 2009

By He De-wen

Based on the principle of life cycle assessment (LCA), municipal solid waste management (MSWM) was analyzed by life cycle inventory method. According to the system expansion and substitution method, the content and frame of life cycle analysis is summarized and applied to municipal solid waste. On the basic of feasibility research of life cycle analysis on MSWM, the paper put forwards complete and concrete ?three changes? measures under life cycle analysis on MSWM. Some aims of MSWM can be achieved under above conditions of LCA on MSWM: to improve the current system efficiency of MSWM; to enhance the serve quality of MSWM, to increase recycle garbage from MSW; to reduce waste amount and reach minimization and innocuity aim of MSWM; to help the departments of MSWM to get over all difficulties to realize their ideal goals.

Jan 1, 2009

By S. A. Abdel Sabour

Conventional methods for selecting a production plan for an open pit mine is based on the assumption that ore grades throughout mine life as well as market variables are known with certainty. Another important issue that is also being ignored in the conventional procedure is the value of management flexibility to revise operating policy with time according to the arrival of new information. Based on this oversimplification of reality, an optimum mine plan that is thought to be maximizing net present value (NPV) of the project is selected. Given the multiple sources of risk affecting the estimated NPV, there is a high probability that the actual value will be different from that estimated. This could mislead decision making process regarding selecting an optimum mine plan. This paper proposes a multi-criteria ranking system for selection between alternative mine designs under both geological and market uncertainties. The system is based on integrating multiple market and geological uncertainties as well as the operating flexibility to revise the ultimate pit limits using a Monte Carlo-based real options valuation (ROV) model. To compare the methods, the article applies the proposed system, along with the conventional NPV-based method, to rank possible mine designs for a copper and a gold mine. It has been found that, considering multiple risk analysis measures while integrating uncertainty and operating flexibility results in selecting a mine design that is different from that selected by the conventional method.

Jan 1, 2009

By Ted Klemetti

Roof deterioration in weak moisture-sensitive rock leads to roof falls in coal mines. An observation site was set up in intake air at an underground coal mine in central Ohio to evaluate the time-dependent deterioration of moisture-sensitive roof rock. By periodically collecting and weighing the rock falling from the roof, the National Institute for Occupational Safety and Health (NIOSH) was able to quantify the deterioration of the moisture-sensitive shale roof. The measurements showed that more roof rock is falling in the dry winter months. Movements in an intersection were monitored in order to determine if deformation correlated with seasonal changes in temperature and humidity. The rate of intersection roof-to-floor convergence was found to be cyclical and related to seasonal changes, with more convergence during the months of April through September. At the study site intersection, the roof beam did not show deflection indicating movement most likely due to mine floor deformation. The bolt load also increased in the warmer months before shedding load, possibly due to rock failure. Temperature and relative humidity sensors, placed in holes in the roof show that mine air does not mix with the air in the holes. Consistent saturation levels of relative humidity were measured in the holes and it appears that high levels of moisture may have migrated into the bolt holes from roof shales. A roof sealant applied to a portion of the test roof appears to be preserving the roof and reducing the amount of rock fall into the entry, while the screened area virtually eliminated rock falling from the roof.

Jan 1, 2009

The first thing to be aware of is that the warming effect of carbon dioxide is strongly logarithmic. Of the 3¦ that carbon dioxide contributes to the greenhouse effect, the first 20 ppm has a greater effect than the following 400 ppm. By the time we get to the current level of 384 ppm, each 100 ppm increment will produce only about 0.1¦ of warming. With atmospheric carbon dioxide rising at about 2 ppm per annum, temperature will rise at 0.1¦ every 50 years for the next couple of hundred years before the effect becomes minuscule. The warming of the 20th century, as the Earth came out of the Little Ice Age, was a consequence of short, high-amplitude solar cycles. A number of solar physicists have predicted that the next solar cycle, Solar Cycle 24, will be quite weak. Based on the correlation between solar activity and the EarthÆs climate, a temperature decline of 2¦C is predicted for the mid-latitude regions over the coming decade, equating to the experience of the Dalton Minimum. Anthropogenic warming due to carbon dioxide will not ameliorate this temperature decline. Increased atmospheric carbon dioxide is wholly beneficial due to itÆs fertilisation effect. Efforts to inhibit Australian carbon dioxide emissions are exactly wrong in science.

Jan 1, 2009