Search Documents

By Kot Unrug

Mine seals are necessary in nearly every mine to isolate mined-out areas from the ventilation network. There is a large number of seals in active mines and that number continually increases as the development spreads across the reserves. The recent accident caused by the failure of seals in the Sago mine resulted in new regulations. These regulations have been set based on a principle of eliminating the risk of failure, rather than the sound engineering and understanding of the conditions that may cause seal failure during an explosion of methane in sealed areas of the mine including the probability of such occurrences. This paper discusses the following subjects related to mine seals: The potential causes of methane explosions and the dynamic effects of pressure wave propagation. Seal materials and methods of construction in view of the interaction of the seal with the host rock environment as well as requirements for gathering geotechnical data. The design of seal dimensions is based on loading conditions, therefore the probable ranges of such loading is reviewed. There is also discussion of possible methods for shielding of seals from pressure pulses following an explosion. Particular seal?s types are examined in reference to the conditions at the seals location. A novel design is presented that will be a low- cost solution for the sealing of mined out areas. Recommendations are given for further research leading to a rational engineering system for design of new seals in coal mines.

Jan 1, 2008

By Von L. Richards

Rapid Freeze Prototyping (RFP) is a novel solid freeform fabrication technology that creates parts by depositing water droplets and freezing them rapidly to form layers. An investigation into the smallest thickness that can be achieved by the RFP process was conducted. The factors that could significantly affect the thickness of the part built by this process including substrate temperature, volumetric feed rate, table velocity, nozzle frequency, nozzle standoff distance, and head pressure were considered. A shell building technique for use with the RFP system has been developed. Thin wall ice patterns have been invested using production shell building techniques and an alcohol-based slurry. The finished shells were quantitatively evaluated by inspecting their total shell thickness, mold cavity dimensional reproducibility, and shell strength. Pattern loss is influenced by not only the alcohol / water interaction but also the starting thickness as it relates to thermal mass.

Jan 1, 2008

By Bill Stormes

This paper will discuss implementation of the Hilti OneStep rock anchor technology to improve face bolting operations during the May 2008 longwall move; increase rock anchor installation capacity; and improve safety by reducing employee exposure periods by utilizing the Hilti OneStep rock anchors.

Jan 1, 2008

The Gordonsville Operation of Pasminco US Inc. along with the Center for Advanced Mineral and Metallurgical Processing (CAMP) at Montana Tech studied, developed and implemented a pilot-scale hydrometallurgical facility for the industrial recovery of germanium and gallium. This paper describes the joint testing and engineering programme that culminated in this successful process.

Jan 1, 2008

On Nov 1, 2007 House Resolution 2262 ? The Hardrock Mining and Reclamation Act of 2007 ? was passed by the U.S. House by a vote of 244-166. HR-2262, among other things, would impose a 4-per-cent royalty on existing mines with commercial production and an 8-percent gross royalty on all new claims. Not surprisingly, this possible new law was one of the hottest topics of discussion at the Northwest Mining Association?s conference that this year returned to Spokane, WA for its 113th annual meeting on Dec. 3-7. More than 1,800 delegates attended the conference that was held under the banner theme of ?Mining ?. For today and tomorrow.? Northwest Mining Association executive director Laura Skaer was one of many speakers during the three-day conference to respond to the threat to the industry posed by HR-2262 with a presentation titled ?Potential changes to the 1872 Mining Law.? In the presentation that she first unveiled at the Alaska Miners Association?s convention and trade show on Nov. 8, Skaer laid out a comprehensive list of problems with HR-2262. In addition to the association?s obvious concerns about the proposed royalty, Skaer noted that the bill includes a mine veto provision that would allow the Secretary of the Interior the authority to deny an operations permit to a project if the secretary determines that the operation would cause undue degradation to public lands and resources. Potential massive withdrawals from mineral entry are also included in HR-2262. Among the lands that could be off limits to miners under HR-2262 are wilderness study areas, areas of environmental concern and 23.6 hm2 (58.5 million acres) identified as Roadless Rule. States, political subdivisions and Indian Tribes would also have more authority to withdraw lands, she said. To combat the proposed changes, Skaer made 10 trips to Washington D.C. on behalf of NWMA members in 2007. In her presentation at the annual meeting, she also objected to provisions that include no life-of-mine permits and uncertain permit renewals and new and duplicative environmental standards that she said are vague, ambiguous and inconsistent with current federal and state environmental laws. Debra W. Struhsacker, an environmental permitting and government relations consultant, also spoke on the issue of HR-2262 with a presentation titled ?The House mining law bill ? Rip van Winkle is back ? and he?s meaner than ever.?

Jan 1, 2008

By Paul Downing

When was the last time the documents and paperwork were cleaned out of the glove boxes, door pockets, under the seats and above the visors in your company vehicles? Insurance cards that expired three years ago and vehicle registrations from 1999 through 2003, for instance, don’t do any good and just take up space

Jan 1, 2008

By K. V. Sreenivas Rao

Solidification experiments have been conducted to study the effect of interface heat flux and air gap formation on cooling rate of the casting during solidification of Al-4.5wt%Cu alloy. The thermal history of the casting and mold during solidification is recorded using thermocouples connected to computer interfaced data logger. The measured temperatures in the mold are used as input to the IHCP (inverse heat conduction problem) algorithm for simulating multiple heat flux components at the boundary. It is observed that the filling effects induce spatial variation in the thermal field in the mold and casting regions and greatly influence the cooling rate of the casting. The study demonstrates the use of IHCP and in-situ measured thermal profile in analyzing the cooling rate and microstructure.

Jan 1, 2008

With a growing concern over mine fires, prevention and suppression are hot topics. NIOSH researchers Michael Trevits, Alex Smith and Edward Thimons discuss their research in the area. The leading causes of US mine fires include flame cutting and, welding operations, frictional heating and ignitions, electrical shorts, mobile equipment malfunctions and spontaneous combustion. From 1990 through 2007, there were 1601 reportable fires that occurred in the US mining industry -an average of 89 fires per year. The fact that mine fires are occurring with alarming regularity reinforces the importance of recognizing and eliminating the potential hazards. These statistics also show the need for improved control and suppression technology to ensure worker health and safety if a mine fire does occur.

Jan 1, 2008

By Matthew Janes

The new Bow office complex will become the new headquarters of EnCana Corporation, a leading Canadian oil and gas company. The shoring system, encompassing nearly two city blocks and excavated to a depth of 20.5 m, supported surrounding utilities and buildings in downtown Calgary. Past excavations in the area experienced large amounts of rock movement, the mechanics of which were poorly understood. The focus of this paper is the design process and construction results concerning rock movement and the effectiveness of the shoring structure. A lack of information regarding the local in-situ stresses and shear band propagation in the bedrock led to research of case studies in the Calgary area and a peer review from local experts. Several geotechnical scenarios were analyzed using FLAC to account for varying residual rock stresses and the location and composition of weak rock layers suspected of causing shear band movement. Movement characteristics were predicted that would identify the rock deformation mechanic throughout the construction process. A detailed monitoring programme composed of precision monitoring targets, inclinometers, and extensometers was established to provide accuracy and redundancy in establishing the movement of the rock and excavation support structure. The results of the programme were used to identify the rock deformation mechanics and further refine the FLAC analysis. To date, monitoring indicates that localized shear band effect is the leading cause of rock movement. The phenomenon appears to be directionally dependent and strongly correlated to excavation extent.

Jan 1, 2008

By S. Slottee

The disposal of plant tailings in a safe and environmentally acceptable manner has taken on increased importance throughout the world, across all types of mineral beneficiation plants. In the U.S. plant life span, expansions and new plants in the current robust mineral markets are faced with environmental pressures to minimize the use of land for disposal by maximizing existing tailings pond capacity. The combination of many drivers from economic to environmental have brought paste thickeners into the coal industry (PasteThick 2007) Thickening tailings to a more concentrated slurry is a common step in the disposal flow sheet. Thickening to a non-settling ?paste?, also called ?thickened tails? or ?tailings stacking?, is a relatively recent development. This paper describes the paste thickener as an alternative for dewatering a fine coal refuse (tailings) stream for deposit as a paste. Initial operating results of the paste thickener are discussed.

Jan 1, 2008

By Zhong Juya, Wang Yong, Guo Xueyi, Song Yu, Tian qinghua

"In this work, the flow of zinc in China, 2004, was traced within the STAF model, and the situation of production, consumption and recycling of zinc resources in China were introduced. The SFA is performed on zinc flows during its one year life cycle in detail. The result reveals that China produces and utilizes a large amount of zinc, while the efficiency of renewable zinc resources is still relatively lower. As one of the biggest producer and consumer of zinc in the world, China is facing a severe depletion of zinc resources. How to increase the resource efficiency is a significant issue for zinc industry of China. Based on the result, several advices were proposed in the paper, aiming to contribute important reference information for the industrial metabolism and resource management and recycling of zinc industry in China. IntroductionZinc is one of the important metals in national economic development in China; it has good conductivity and corrosion resistance, with high scalability when heated to 100 ~105_. Zinc is mainly used for galvanized zinc industry, as the coating of steel and various parts, and it has also been applied to the manufacture of brass, bronze and corrosion-resistant alloys, which are widely used in machinery manufacturing, printing, national defense and so on. In addition, zinc compounds are utilized in various fields, for example, ZnO is used for infiltration wood, paper, rubber, paints, etc.; ZnSO4 for leather, ceramics, textiles, medicine, etc.; ZnCl2 for infiltration wood; ZnS2O4 and Zn (HSO2 • CH2O) 2 for the paper and textile bleaching, etc. [1]. The extensive use and consumption of zinc in industrial production and social life promot the rapid development of zinc industry, which made zinc the third largest non-ferrous metals in the world."

Jan 1, 2008

By A. Eslami

In recent development of piled raft design, the contribution of both raft and piles to tolerate the loads is taken into account, depending on the stiffness and contributions of involved elements i.e.; piles, raft and surrounding soil. The piles are usually required not to ensure the overall stability of the foundation but to act as settlement reducers. One alternative method of foundation design is therefore to introduce piles purely as a means of improving or enhancing the stiffness of the base soil by structurally disconnecting the piles from the raft. In this paper, two and three dimensional finite element analysis of disconnected pile-raft systems are performed on three case studies including a 12-storey residential building in Iran, a 39-storey twin tower in Indonesia, and the 256m height of Messeturm tower in Frankfurt, Germany. The analysis include different geometrical parameters, e.g., pile spacing and embedment length, arrangement and raft thickness for foundation system to obtain the optimized design functions and to clarify the role of each parameter and method of analysis. The parametric study results and comparison to a few field measurements indicate that by concentrating the piles in the central area of the raft foundation leads to the optimum design with the minimum total length of piles. This achievement can be considered as a criterion for project cost efficiency. On the other hand, disconnected piled-raft systems can significantly reduce the settlements and raft internal bending moments. Finally, the comparison indicates that simple and faster 2D analysis has almost the identical results to 3D analysis which is complicated and time consuming.

Jan 1, 2008

By M. I. Brittan

Cyanide leaching of two West African gold ores was studied in multiple laboratories to provide process-engineering data for plant design purposes. Unusually slow leach extraction kinetics were observed using routine cyanide leach test procedures with pregnant solution monitoring. Carbon-in-leach testing, however, showed normal rapid kinetic behavior, with the same ultimate gold extractions being reached in much shorter elapsed times. Kinetic curves based on washed solids assays also exhibited more typical leaching characteristics. The results bore all the hallmarks of some equilibrium inhibition of the leaching. It was surmised that ore gangue components were responsible for weakly adsorbing gold-cyanide complex reaction product, thereby holding up soluble gold in the solid phase. The term ?preg-borrowing? was coined to describe the reversible phenomenon and distinguish it from irreversible preg-robbing. The two ores investigated may represent an extreme form of a more general effect that in most instances might pass unnoticed. The effect can lead to misinterpretation of kinetic leach curve data and underestimation of calculated ore head grades.

Jan 1, 2008

QEMSCAN« technology is a widely accepted automated e-beam technique providing quantitative and statistically robust mineralogical data to the mining industry. It uses X-ray mapping combined with backscattered electron (BSE) brightness to identify minerals in almost any type of geological material (Gottlieb et al, 2000). Besides the modal mineralogy also the liberation, associations, average grain size and other textural information can be obtained. The aim of this study is to test reproducibility of this technique by setting up and running standard tests on different QEMSCAN« systems. Multiple sample blocks were prepared by our standard operating procedure as epoxy-mounted, carbon-coated, polished blocks. The replicates were measured under the same conditions and measurement parameter settings on different QEMSCAN« instruments. The relative standard deviation (RSD) for the set of measurements was calculated. Generally the reproducibility of the systems themselves was found to be excellent, ranging between 0.4 and 1.5 per cent RSD. The more significant change in the reproducibility was found to be caused potentially by the sample preparation and variation in the mineralogy of the replicates. The measurement parameter settings together with these variations can account for almost 15 per cent RSD for minerals of low abundance. For analysed samples good results for the main phases present in quantities higher than 2 - 5 wt per cent of the total mass of the sample were confirmed with RSD generally below six per cent. Following the experiments, the parameters having the biggest influence on the performance of the QEMSCAN« and its precision are discussed in detail. The importance of sample preparation procedures and measurement parameter settings is emphasised. It is shown that experience and excellence is necessary for getting the most from the automatic mineralogical methods like QEMSCAN«.

Jan 1, 2008

We present a novel hybrid algorithm for quantifying the ore grade variability that has central importance in ore reserve estimation. The proposed algorithm has three stages: (1) fuzzy clustering, (2) similarity measure, and (3) grade estimation. The method first considers data clustering, and then uses the clustering information for quantifying the ore grades by means of a cumulative point semimadogram function. The method provides a measure of similarity and gives an indication of the regional heterogeneity. In addition, grade estimations can be obtained at different levels of similarity using a weighting function, which is the standard regional dependence function (SRDF). Keywords: Grade, fuzzy clustering, similarity measure, point madogram, weighting function.

Jan 1, 2008

I am interested in experiences people have had with blasting near existing railroad tracks: What kind of vibration criteria are used, and how successful you have been in gaining approval for blasting in the vicinity of railroads. This would both be for passenger and freight railroads

Jan 1, 2008

Pillars in underground limestone mines are required to support the overburden and provide a safe, stable working environment for mining personnel and equipment. Pillar stability was assessed by the National Institute for Occupational Safety and Health in underground limestone mines in the Eastern and Midwestern United States. It was found that current mine layouts have been successful in providing support to the overburden, while a small number of isolated pillar failures were observed. The stable pillar layouts and failed pillars were plotted on a chart that demonstrates the relationship between pillar width-to-height ratio and pillar stress. The results show that pillar failures occurred at the lower range of width-to-height ratios and can occur at relatively low stress levels. Zones indicating the potential risk of pillar instability are shown on the chart, based on hazards associated with the onset of rib spalling, large angular discontinuities and unconfined pillars. The chart can assist limestone mine planners to evaluate potential instability in current or new pillar layouts that are similar to those included on the stability chart.

Jan 1, 2008

By Piotr M. Kapias

Keywords: extraction, lead refining, Pb-Tl solutions, PbCl2-TlCl solutions. The theoretical part of the paper presents an analysis of the conditions of Tl extraction from Pb using different extractants and determines the activity coefficients in liquid solutions of Pb-Tl and PbCl2-TlCl. The dependence of the solution activity coefficients upon the composition and temperature is presented in the form of Krupkowski and Krupkowski-Fitzner equations. An analysis and evaluation were made of the influence of the methods of PbCl2 introduction into a Pb-Tl solution upon the efficiency of the Tl extraction process under thermodynamic equilibrium conditions. The analysis made it possible to formulate relevant equations describing the dynamics of the process of Tl extraction from Pb under stirring conditions as well as under the extractant injection into the liquid Pb-Tl solution conditions. In the part concerning experimental work, results are given for tests on the Tl extraction process from Pb-Tl liquid solutions of initial Tl content of approximately 0.05% mass using PbCl2 or, alternatively, Cl2(g) conducted in laboratorial scale. The tests made it possible to establish the influence of time, temperature, mass and the method of introducing the extractants into the liquid upon the level of Tl extraction from a Pb-Tl solution. Labels used in the text. WT1m - TI content in metallic phase, % mass WT1s - TI content in chloride phase, % mass wpTlm - TI content in metallic phase in initial state, % mass W°Tlm - TI content in metallic phase in equilibrium conditions, % mass m°m - initial mass in metallic phase mm - mass in metallic phase mPbC12 - lead chloride mass fed to the system MPbC12-TIC1 - mass in chloride phase MPb - lead atomic mass, g/mole MT1 - thallium atomic mass, g/mole K - Nernst distribution coefficient Xi - mole friction of solution component X°PbC12 - mole friction of PbC12 in saturated solution X°T1C1 - mole friction of T1C1 in saturated solution T - temperature, K R - gas constant, J/(mole K) k - kinetic equation constant, 1/(%-min.) ?i - solution component activity coefficient e - extraction rate, %

Jan 1, 2008

By Simon J. McDonald

In late 2007 Neptune Minerals Plc. commissioned Genesis - a leading consultancy and engineering company affiliated to the Technip group - to undertake a Seafloor Mining Conceptual Study for mining of Seafloor Massive Sulphides (?SMS?) in Neptune?s New Zealand licenses. A key deliverable of the study was information to de-risk the perception of SMS mining for investors the minerals, and that deep-sea mining of SMS material is technically feasible, commercially viable and can safely be managed as a sustainable marine resource industry. The aim of the study, completed in April 2008, was to evaluate alternative existing marine technologies for seafloor mining, ore lifting, dewatering and surface offtake, considering the following parameters: ? Efficiency; ? Reliability; ? Safety; ? Environmental impact; and ? Cost

Jan 1, 2008

By S. Aguayo-Salinas, J. L. Valenzuela-García, A. L. Leal-Cruz, M. I. Pech-Canul, M. T. Certucha-Barragán

"The aim of this research was to carry out a comparative and systematic study of the degradation of cyanide by hybrid natural/biodegradation and biodegradation methods using a mixture of Pseudomonas sp and Bacillus megaterium native bacteria. Bioreactors consist of filled columns with contaminated ore containing 100 ppm of total cyanide. In the biodegradation tests a mixture of bacteria was inoculated into the biodegrading solution. Results of cyanide degradation show a similar asymptotic behavior in both the hybrid (opened system) and biodegradation (closed system) methods; however, for the same period of time (72 h) the permissible maximum levels (1-2 ppm of cyanide) are only attained in the closed system. While in the closed system the cyanide levels are reduced from 100 to 1.5 ppm, in the open system, cyanide decreases from 100 to 2.4 ppm.IntroductionOne of the most important tasks of mining industry is the treatment of the wastes generated in mining operations. Accordingly, industrial waste waters and ores represent a complex problem and a great challenge. In addition to ethic and communitarian considerations, there are laws that prohibit or regulate the contamination of water and air. Moreover, they establish that the restoration of wastes must be considered as a necessary operation cost [1]. Currently this important problem is being addressed by the mining and metallurgical industries using different approaches; mainly they are focusing on the treatment of waste waters and ores generated by the leaching process in which cyanide is used as a leaching agent for the recovery of precious metals as gold and silver. Cyanides have toxic characteristics and thus negatively impact the environment when they are discharged to the ground without previous treatment. While there are some processes in current use there are others that have only been proposed and that allow cyanide degradation, transformation to less toxic compounds and/or the complete elimination of cyanide. The second group includes a variety of techniques that use natural, chemical and biological treatments. Natural treatments consist of the passive abandoning of the heap and of its washing with water. Since these processes are slow and generate great volumes of water partially contaminated, then other alternatives should be considered."

Jan 1, 2008