Search Documents

By Clifford J. Wren

A geotechnical foundation solution was required to halt and prevent further structural distress suffered by a residential four storey apartment building in Hamilton, Scotland. Residents of the ten year old building started to notice cracking and signs of distress approximately one year after moving into the property. A detailed intrusive inspection of the structure revealed that the building was moving and had suffered significant settlement and structural distress at the shared party wall between it and an adjoining building. Roger Bullivant Limited (RBL) was appointed Principal Contractor to carry out an agreed remedial works contract which included a complete structural ?strip-out? of the ground floor, underpinning, contiguous bored pile retaining wall and reinstatement. The paper describes how a proprietary pile and needle beam underpinning system was used to prevent further differential movement and provide a new secure foundation for the residential building. The case study illustrates how a flexible problem solving approach can be applied to a difficult and sensitive geotechnical project.

Jan 1, 2008

By Charles D. Litton

Laboratory experiments were conducted to determine the responses of a prototype smoke detector and a commercially available photoelectric smoke detector to smoke particles generated from various combustion sources. The prototype smoke detector combines optical scattering measurements with ionization chamber measurements in order to reduce/eliminate nuisance alarms due to the presence of airborne dusts or diesel exhaust particles. The commercially available smoke detector is designed for use in harsh environments where airborne dust represents a major problem due to both nuisance alarms and detector contamination. In the experiments, the responses of the two detectors were measured when exposed to smoke particles from the exhaust of a diesel engine and from a variety of fire sources, including wood, coal, styrene butadiene rubber, and No. 2 diesel fuel. For the solid fuels, data were obtained for both smoldering and flaming combustions. This report describes the experiments, their results, and the use of these results as they apply to early-warning fire sensors capable of the rapid and reliable detection of fires in atmospheres that may or may not be contaminated by either airborne dust or the products produced from diesel engines.

Jan 1, 2008

By Haldun Kurama, Cenk Karakurt, Ilker Bekir Topçu

"The usage of binders or pozzolanic materials in the production of concrete is not new. However, in recent years, the use of the pozzolanic siliceous material such as natural zeolite and coal combustion ash (CBA) has received re-attention due to the generated considerable interest in the economical use of both naturally occurring raw materials, recycling of the waste material and saved energy. In this study, the potential and utilization opportunities of natural zeolites and bottom ash (BA) in concrete applications were reviewed. Case studies, conducted to determine the possible usage of the natural zeolite and BA in concrete production, i.e. light weight concrete (LWC) were also presented. The physical and mechanical properties of cured concretes were examined to find out the competitive material usage on the final product properties. Autoclaved aerated concrete (AAC) with 1.1 nm tobermorite (5CaO 6SiO2 5H2O) as binder is a lightweight construction material that mainly uses in place of concrete to manufacture various building materials, including blocks, panels, slabs and the like. The material is a mixture of sand, lime, cement, gypsum, water and an expanding agent, which causes the raw material to rise like bread dough, with countless small air pores. AAC can be molded and cut into precisely dimensioned units and cured in an autoclave, which steam cures the concrete under pressure. During this process, the ingredients combine to form the calcium silicate hydrate gels that establish the special properties of the finished product. The process produces a material that is only one-fourth to one-third the weight of a conventional concrete block (bulk density of 400-800 kg /m3) of the same size. Regular AAC offers considerable advantages over other construction materials such as high thermal and sound insulation, excellent fire resistance, high resource and energy efficiency, low environmental impact, and finally outstanding structural performance (especially for earthquake zones) [1]. Its lightweight also makes it easy to use during construction, and its aerated structure gives it better thermal insulation and sound absorption properties than conventional concrete."

Jan 1, 2008

By H. B. Sahu, N. M. Mishra, D. C. Panigrahi

The paper presents the development of a spontaneous heating liability index (SHLI) of coal based on a mathematical approach. The parameters for the calculation of this index have been determined by differential scanning calorimetric studies. Thirty-one coal samples representing both fiery and non-fiery coal seams of different ranks have been collected from different Indian coalfields and their SHLI values have been determined. In addition, the susceptibility of these samples to spontaneous combustion has been ascertained by standard crossing-point temperature measurement. The moisture percentage of all the samples has been obtained by proximate analysis. A comparative study between SHLI and crossing-point temperature, along with moisture percentage, indicates that SHLI predicts the proneness of coal to spontaneous heating more accurately.

Jan 1, 2008

By Carlos Eduardo Gomes de Souza, Luis G. S. Sobral, Paulo A. Medeiros da Silva, Selma G. F. Leite, Renata de B. Lima

"The use of mixed cultures of acidophilus microorganisms that act in different temperature ranges, aims at speeding up the digestion of chalcopyrite, highly refractory sulphide mineral, the major mineral in the flotation concentrate of Caraíba Mining Co., with an attractive processing cost. The concentrate under consideration contains mainly chalcopyrite (CuFeS2) and bornite (Cu5FeS4) with contents of, approximately, 70 and 30%, respectively. It was observed in this study, the performance of consortium of mesophiles, moderate and extreme thermophile microorganisms, in the oxidation of the aforementioned sulphides minerals, evaluating operational parameters such as pH of the leaching solution, the reaction temperature and redox potential, with consequent extraction of 80% of the concentrate copper content within 60 days of bioleaching. Such high copper extraction was achieved in column bioleaching tests.INTRODUCTIONThe solubilization of metals by the application of microorganisms from the mineral ores and the subsequent recovery of metals from solution are referred to as bioleaching (Rohwerder, T et al, 2003). This is an economical method for the recovery of metals from minerals; especially lowgrade ores, overburden, and waste from current mining operations which requires moderate capital investment with operating cost (Watling, 2006).Furthermore, bioleaching is generally more environmentally friendly than conventional metal recovery processes such as concentration and smelting. Those physicochemical metal extraction processes generate sulphur dioxide, a toxic emission that is increasingly the target of regulatory legislation (Stott et al., 2000; Olson et al., 2003). Bioleaching of chalcopyrite is the key industry target. The main problem hindering commercial application of chalcopyrite bioleaching is the slow dissolution rate (Fu et al, 2008).Dissolution of acid-soluble sulphide minerals such as sphalerite, and to a lesser extent chalcopyrite, occurs by a combination of ferric iron and proton attack via the polysulphide pathway (Rohwerder et al., 2003)."

Jan 1, 2008

By B. V. Driga

The paper presents the evaluation method of the thermal power potential of the salt lakes developed in collapsed salt mines in Romania. It is well-known that the hydro-chemical stratification of these lakes favors warmer internal layers. The degree of heat varies during the year, but, taking into account the large number of genetic lakes of this type, it can be used as a local utilizable power source. The authors analyze the correlations between the physico-chemical parameters of the water and the degree of heat stored as a function of the morphological parameters of the lakes, as well as the technical parameters for capitalizing on this power.

Jan 1, 2008

By Adam K. Smith

Occupational hearing loss is a permanent illness with no recovery currently possible. For underground coal mine workers, Noise Induced Hearing Loss (NIHL) continues to be a serious health issue. One of the principal and fundamental machines used in underground mining operations is also one of the loudest. Noise generated on the continuous mining machine is the result of 3 operational components: the cutting system, the dust collection system, and the onboard conveying system. During underground acoustic evaluations, the conveyor system noise was observed to be dominant. In order to more closely examine sound generated by the continuous mining machine, sound power levels were measured in a reverberation chamber at the Pittsburgh Research Laboratory (PRL). Different chain types and configurations were installed on the conveyor system, and the resulting sound power level ranged from 118 dB(A) to 108 dB(A). Noise generated by the dust collection system was also examined and found to be 107 dB(A).

Jan 1, 2008

By Mark Coleman

Pnuematic Conveying and Process Injection Technologies have been implimented in the metals markets for the last 40 years and have consideribly improved the productivity and the performance of many processes. There have been many steps forward in handling technology and this paper seeks to consider those now offered by Clyde Materials Handling who as an established customer-driven solutions provider, which has turned its attention to supporting the Metals Market. Clyde seek to utilises its knowledge, expertise and technologies to transform the production processes of its customers, who operate in the ferrous and non-ferrous metals industries. With over 30 years experience in the process improvement industry, Clyde Materials Handling has helped their global customer base transform the way in which they operate their processes, which has enabled them to generate sustainable economic benefit and maintain their positions as leaders in their respective markets. Operators within the metals market have developed and deployed pneumatic conveying and pneumatic injection technologies. These environmentally supportive and sustain-able solutions have been used to transport raw materials within operating facilities, from storage to silo, as well as injecting these materials directly into the heart of production processes. Operators, such as Codelco in Chile, Corus Steel in the UK, and many others across the World have seen pneumatic injection solutions transform their process and costs. To inject a consistent, pulseless and accurate flow of material to a copper concentrate bath smelter, or injecting granular or pulverized coal as a coke substitute in to a blast furnace via the Tuyeres helps to increase the operational capacity, availability and productivity and reduce the cost of the operation. This paper will discuss and highlight the ways in which pneumatic conveying and injection technologies, created by Clyde Materials Handling, and applied in partnership with the customer, have helped to improve the operational performance of the production processes of operators across the non-ferrous metals markets with specific reference to applications in the Lead and Zinc Industries. With examples from Zinc Fuming in Australia, Zinc Calcine and Powder Handling in Korea, Precision coal injection to QSL and TSL Furnaces, and metered distribution of Zinc Calcine to Reactors.

Jan 1, 2008

By H W. Wu, T Harvey

An overview is given of two new developments in mine atmospheric monitoring. A new personal dust monitor (PDM) that gives real-time respirable dust readings is discussed. The unit is mounted within the minerÆs cap lamp battery and internally measures the true particle mass of dust collected on its filter. Samples are available for later mineralogical analysis and results do not exhibit the same sensitivity to water spray as optically-based measurement approaches. The technique achieves microgram-level mass resolution even in the hostile mine environment and reports dust loading data on a continuous basis. The monitor has been evaluated under an Australian Coal Association Research Program (ACARP) grant and is being adopted for statutory mine respirable dust determinations in the United States (US). The monitor has particular application for determining location of high dust sources. It can evaluate the efficiency of engineering means of suppression and other approaches to reducing dust levels. It has been recognised that the PDMÆs unique measurement approach has application to allow real-time atmospheric diesel particulate matter (DPM) monitoring. The industry has no real-time atmospheric DPM monitor at present. Recent surveys in New South Wales and Queensland show significant numbers of miners continue to face full shift DPM exposures in excess of internationally accepted levels. Real-time DPM monitoring will allow the industry to pinpoint high exposure zones where a number of trucks and other vehicles work in areas of poor ventilation. Knowledge of high DPM concentration zones allows efficient modification of work practices to reduce underground minersÆ exposure. Approaches to uses of the DPM form of the monitor and the design of tag boards are discussed. Some outcomes from mine tests with both these new instruments are given.

Jan 1, 2008

By Bill Zietlow

A micropile and soil nail underpinning system was installed to support a building immediately adjacent to a 25-ft deep excavation in downtown Salt Lake City, Utah. Both the building and the underpinning were instrumented to monitor deflections, rotation and crack growth. The underpinned structure consisted of a two story concrete masonry unit (CMU) building founded on shallow spread footings attached to a concrete high-rise building on spread footing two floors below grade. The face of the excavation was 10 in. in front of the underpinned building foundation wall. The underpinning system consisted of small diameter hollow bar micropiles installed with injection grouting techniques below the bottom of the excavation and attached to the underpinned structure by a concrete pile cap doweled into the existing footing. The lateral loads imposed by the soil under the underpinned structure were designed to be supported by the soil nail wall installed through the micropiles during excavation. The settlement monitoring instruments consisted of crack gages, optical survey prisms, high sensitivity vibrating wire water levels and biaxial vibrating wire tilt meters. They recorded maximum movements of approximately 0.1 in. of settlement, 0.05 deg. rotation (top of wall rotating away from excavation) and up to 0.08 in. of crack opening during the excavation until one month after the soil nails and shotcrete facing were completely installed. This movement was well within both the estimated settlement and the estimated settlement tolerance of the underpinned structure.

Jan 1, 2008

By Fatbardha Osmani, Skender Osmani

"A system analysis of the resource and environment management (water, energy etc) starts from its definition. Unfortunately, there is not a unique semantics of the mentioned concept. On these circumstances, in this paper the following issues are presented: 1.A short view on the existing concepts of management. 2.A new definition on the concept of management. It is considered as a complex and rational activity on human and natural resources ,environment etc, which starts from a analysis of infrastructure ,technology , etc, mission , alternatives , project etc. and ends to an optimal output. Basing on this definition, the management has two principal components: strategy and policy. The strategy is referred as a blue print program (the same definition as in Game Theory), which contains all the contingency alternatives. , while the policy is referred as a strategy applied into practice. The strategy is the first , while the policy is the second one. The best alternative of a policy is the project, Each strategy has one and only one project. The mentioned definition erases the differences between concept of policy and politics. Each strategy has its alternatives ,the next has its sub strategy and so on, i.e. whatever are going to be the strategy, there are a hierarchy composed by sub strategies up to the simplest strategies applied by a single individual (human beings or robots). The strategy objectives are necessary and sufficient conditions for its realization i.e . the strategy is an optimal activity, in which all resources are integrated and processed . Several strategies could be joined into one( for example the surface water strategies of the Balkan countries) . In this view, the strategy could be globalized into optimal way basing on different criteria’s as social, economic, environmental, their risks and effectiveness etc. etc An example from the water management illustrates the mentioned concepts."

Jan 1, 2008

By L. F. Miao

Studies were carried out to investigate the ultimate soil pressure acting on pile(s) undergoing lateral soil movement in soft clay. A special apparatus has been designed to apply a uniform rectangular profile of lateral soil movement on the rigid pile(s) with pinned head and tip conditions to obtain the ultimate soil pressure. The piles were 16 mm (5/8 in) in diameter. For the pile group tests, the behavior of different number of piles (2, 3, 4, 6 and 9), pile arrangements and center-to-center spacings (3 and 6 diameters) were investigated. In this paper, the group factors of 11 combinations of number of piles, pile arrangements and pile spacings are presented. The group factors are given for individual piles in a pile group as well as for the entire group. Generally, the group factors of individual piles in a group varied significantly according to pile spacing in both directions, and pile arrangement; the group factor of the whole group reduced with an increasing number of piles, and increased with increasing pile spacing. For a pile group with the same number of piles but different pile arrangement, no significant difference was found in the group factors for the entire group.

Jan 1, 2008

By Stephen Yirenkyi

The mining industry remains the backbone of many economies in the developing world. Its resurgence in Ghana since 1989 was driven by the global paradigm which emphasizes private sector-led development as the engine of economic growth in developing countries. The historical importance of mining in the economic development of Ghana is evident in the country?s colonial name, Gold Coast (Akabzaa T. and Darimani A., 2001). Ghana earned $2.5 billion from mineral exports in 2007. 20,000 people are employed in large-scale mining whilst 500,000 are employed in the small-scale sector. Mining contributes about 7% of Ghana?s total corporate tax earnings, 41% of total exports, 12% of revenue collected by the Internal Revenue Service and 5% of Gross Domestic Product (Ghana Chamber of Mines, 2008). Gold dominates the mining sector and the country is Africa?s second largest gold producer after South Africa. Surface Mining, which refers to a method of extracting minerals from the earth by their removal from an open pit or borrows, requires a large tract of land for its operations (Wikipedia, 2008). There is therefore a continuous divergence of interest between land required for surface mining and other land uses such as farming and housing, among others. In recent years, surface mining has been promoted in many mining countries because of the following reasons: ?Cost considerations compared to underground mining; ?Safety considerations, compared to underground mining; ?Low grade ore which requires processing huge quantities; ?Location of the ore bodies; and ?Competition among gold producing countries for investors. This paper looks at the socio-economic impacts and challenges of surface mining by using Gold Fields Ghana Ltd. Tarkwa, Ghana as a case study. The company has a concession of about 208 sq km located in the heart of the Wassa communities in the Western Region of Ghana and undertakes surface mining like most of the other mining companies in the country. Gold Fields, Tarkwa mine produces 700,000 ounces of gold a year with the potential of increasing this output to 800,000 ounces after its current expansion programme. Some of the effects of surface mining identified were: 1. Relocation/Resettlement of host communities and its negative effects; 2. Disturbance to Flora and Fauna; 3. Disturbance to Sacred Places; 4. Land Degradation; 5. Noise and Air Pollution; and 6. Water Pollution. This paper sought to investigate the measures put in place by the government and the Gold Fields Ghana Ltd. to mitigate the above effects in order to ensure peaceful coexistence between the mining company and its host communities. It concludes that most mining companies presume the provision of socio-economic development in mining communities will lead to the company securing a social license to operate. This however is not true but rather effective community relations combined with socio-economic development. According to Gold Fields Ghana Ltds. model, this involves continuous community engagement, conflict resolution and comprehensive environmental monitoring programme which will all lead to effective community relations. The strategies to ensure socio-economic development involves community development programme, livelihood restoration programme and community training and employment. All these will then lead to sustainable development which will ensure the company?s social license to operate. Gold Fields? model is in line with the principles of responsible mining. With this model, the community feels they are part of the company and the social license of the company is guaranteed. Gold Fields? model, which has been tried and tested for the past five years, could serve as a template with suitable modification for local conditions for other mining countries where surface mines operate.

Jan 1, 2008

By R Pozo, F Reyes

Codelco Chile is currently developing the El Teniente û New Mine Level Project (NMLP) in order to increase ore production by seeking to mine the ore deposit located under the current operational orebody. Reserves of 2000 million tonnes (Mt) have been quantified, which will be extracted as from the year 2017 by using the panel caving and progressive sinking method. Codelco and SKM Minmetal (SKM) jointly developed the project prefeasibility stage (PFS), closing these studies in March 2008. The first part of the project approach is to replace mine production currently feeding the Colon concentrator facilities with 137 000 tonnes per day (t/d), focusing attention on a production increase from the year 2026 up to 180 000 t/d. Project efforts have also been centred on maximising the contribution of new technologies for both construction and operational phases of the New Mine Level, together with selecting the best mine infrastructure to keep El Teniente operations going on for the next 50 years. Implicit in this is the inherent improvement of a variety of current Mina El Teniente process and management practices. The plan is to reduce actual mine operational risks and take advantage of new opportunities afforded by the project, which is in effect a greenfield project with respect to the implementation of fundamental changes in the labour and business environment. In addition, issues related to human resources, maintenance and management, materials handling, establishing centralised operations and accesses, automation and remote operations control and power efficiency could also be addressed. The project, beyond the New Mine Level exploitation, considers the mineÆs future potential, with a second deeper exploration in prospect named Deep Level. Finally, the project identifies features that would add value to the mine operations, in an initiative named æSpace for Future TechnologiesÆ. This will allow the eventual implementation of new electrical equipment and the application of mechanised technologies and other process improvements for the mine development.

Jan 1, 2008

By M. Frades, C. Frías, G. Díaz, A. B. Mejías

"In recent years, zinc recovery from flue dusts and other industrial wastes has been increased, offering to the market a large tonnage of secondary zinc oxides, which can not be processed directly to render high quality zinc because of the hazardous impurities and halogens content.The ZINCEXTM Technology has been commercially applied for more than thirty years and represents the most suitable solution to deal with secondary or crude zinc oxides due to its flexibility, simplicity, and cost-efficiency, allowing production of SHG electrolytic zinc and pure zinc sulfate salts thanks to the flexibility and selectivity of the zinc solvent extraction unit regarding to get rid of impurities.A dual plant able to produce electrolytic zinc and crystallized zinc sulfate has been engineered to provide a flexible and profitable solution to zinc market. A description of the study and the relevant achievements is presented in this paper.IntroductionZinc is a valuable commodity in the marketplace and can be recycled again and again and still maintain its physical and chemical properties. Zinc recycling offers both environmental and economic benefits such as reducing volumes of material that end up in landfills, saving energy by reducing the need for mining and smelting, and relieving environmental impact on the land and water, and conserving zinc ore [1].The supply of zinc able to be re-processed will be increasing from year to year according to secondary materials enter the recycling stream, and as a result, more recycled zinc will become available in the market. Thus, some existing zinc refineries are implementing an annexed treatment line to process secondary oxides in conjunction with primary zinc concentrates [2].The galvanized steel scrap is normally recycled in electric arc furnaces or in basic oxygen furnaces, which generates a large tonnage of zinc-bearing flue dusts (EAFD). Around one million ton EAFD is yearly produced at the USA and the EU, respectively. The flue dusts are treated commercially by pyrometallurgical ways such as waelz kilns, electrothermic furnaces, etc, to yield secondary zinc oxides that can not be processed directly to render high quality zinc because of the hazardous impurities and halogens content [3]."

Jan 1, 2008

By Melvin H. Miles

"Considerable research has been conducted on the anodic oxidation of methanol in fuel cells. The electrochemical reduction of carbon dioxide in aqueous solutions to form methanol is the same reaction in reverse, i.e. CO2 + 6 H+ + 6 e- ? CH3OH + H2O. The same catalysts and conditions may operate for both reaction directions. This carbon dioxide reduction reaction, however, must be able to compete with the electrochemical reduction of water to form hydrogen gas. Thermodynamically, the reduction of CO2 to form CH3OH is slightly more favorable than the reduction of water. The use of nearly neutral electrolytes rather than acidic electrolytes makes the reduction of CO2 kinetically more favorable. The thermodynamics of various reaction steps are presented. Similarities exist with the electrochemical reduction of CO2 and the green-plant photosynthesis process that converts CO2 to carbohydrates.IntroductionVirtually all of the oxygen in the earth’s atmosphere is of biological origin having been generated by green-plant photosynthesis from water and carbon dioxide [1]. The net reaction can be represented byCO2 + H2O ? O2 + [CH2O] (carbohydrates, etc.) (1)Chlorophyll and enzymes promote this reaction, and the energy required comes from sunlight. The actual photosynthesis process is a complex multistage reaction and requires 469 kJ mol-1 of energy supplied by the sun. Isotope tracer experiments using 18O have shown that both the oxygen atoms in the O2 molecule originate from H2O, whereas oxygen atoms in the carbohydrates come from CO2 [1]. The total amount of water on the earth is split by photosynthesis and reconstituted by respiration and combustion once every 2 million years or so. The photosynthetically generated oxygen gas temporarily enters the atmosphere and is recycled about once every 2000 years [1]. The carbon dioxide is partly recycled in the atmosphere and oceans after an average residence time of 300 years and is partly fixed by precipitation of CaCO3 and other carbonate minerals [1]."

Jan 1, 2008

By Vladimir Lobanov, Pritchinm Alexander, Nikifor Ageev

"Sulfuric anhydride is one of the most voluminous technological emissions. The possibility of high-temperature SO2 oxidations without catalyst in presence of calcium-bearing filling materials (CaO, Ca(OH)2 and CaCO3) with obtaining of binding material on the basis of waterless calcium sulfate is studied. Due to application package HSC-4 the thermodynamic analysis of the specified interactions is made and following conclusions are drawn: 1) Reactions are feasible in the all range of investigated temperatures (400 – 1000 °?); 2) The best results should be expected at use of ???; 3) The heat of reaction does possible autogenous behavior of process. The researches have shown: 1) Practical possibility of the process; 2) SO2 oxidation without the catalyst is feasible in presence of ???, Ca(OH)2 and CaCO3; 3) The optimum temperature range is 600-800 °?; 4) The content of waterless calcium sulfate in a product reaches 48% that makes it possible to use as the binding material; 5) At excess of ??? the degree of SO2 collection is nearer to 100%. Introduction At processing of sulfide raw materials in metallurgical furnaces the significant amount of sulfur, mainly in the form of sulfuric anhydride is escaped. Rich gases (SO2>3 %) are used for the sulfuric acid or element sulfur production. Chemism of sulfuric acid manufacturing is based on catalytic high-temperature oxidation of anhydride. Poor gases of metal works (SO2 =2,5 %) and power combustion units (SO2 =0,5 %) after clearing discharge into the atmosphere. Commonly, to recovery of weak sulfuric anhydride the chemical and physicochemical methods are applied. A few chemical ways of recycling sulfur dioxide are applied practically. In a number of methods for SO2 recovery a pulp of metals oxides (magnesium, zinc, etc.) with formation of sulfites is used. In other case sulfuric anhydride is catch by weak sulfuric acid in the presence of an oxidizer (pyrolusite ore). Methods of absorption SO2 by solid sorbents, (carbon fibers, silica gels, zeolites) are known and put into practice. Regeneration of the saturated sorbents is realized by thermal decomposition or extraction. Obtained as a result high-concentrated solutions are a commercial product."

Jan 1, 2008

Water retention, water loss and delay in tailings storage rehabilitation are major challenges for many Coal Mines. Work by Stewart, Backer and Busch in the early 1980s suggested that there were improvements to be made in tailings dewatering and density by the addition of flocculant. This prompted ACARP, in cooperation with Bulga Coal Management (Xstrata), to initiate a research project investigating the impact of flocculant addition on tailings deposition density, water retention and the tendency for tailings to form surface crusts suitable for subsequent rehabilitation. A polyacrylamide-based flocculant (200 - 250 g/tds) was injected into the tailings line immediately prior to disposal into the impoundment area. The flocculated slurry rapidly released clear water and created a beach due to the immediate increase in deposition density. The deposition density increased from 35 per cent w/w to 61 per cent w/w solids within 24 hours and continued to increase to 75 per cent, seven days after treatment. The water capture at the tailings storage facility improved by more than 90 per cent; water which would otherwise be lost from the circuit through retention and evaporation. The impoundment capacity had nearly tripled due to the improvement in initial deposition density from 420 kg/m3 up to 1163 kg/m3. Four weeks after disposal surface crusts were forming on the storage facility, suggesting that there would be less delay between cessation and tailings storage rehabilitation.

Jan 1, 2008

By G Lind

Bridging of production stopes in narrow vein gold deposits contributes to significant financial losses and production delays. Bridging is caused when underbreak in the stope production blast occurs, resulting in less than the designed stope blast volume breaking out during blasting. Jundee Operations in the Northern Goldfields of Western Australia extracts ore from its expansive narrow vein orebodies utilising longhole open stoping. In 2006 it experienced bridging in ten panels, or 8.77 per cent of all panels, as well as multiple bridging in 30 per cent of these bridged panels. The Jundee orebodies are west dipping with the bridged panels dipping between 44¦ and 62¦. This paper examines some solutions from the drill and blast design perspective to minimise bridging occurrences. It was found that the then current drill patterns and number of holes were adequate from a longhole stope design perspective. However, changes to the blasting design, specifically modifications to the blast delay initiation sequencing, primer positioning and blasthole dump combined with timely stope surveying and back analysis, were implemented with the aim of preventing bridging in this narrow vein operation.

Jan 1, 2008

By G Partington

A regional scale prospectivity model was developed for Papua New Guinea (PNG) to identify areas of porphyry Cu-Au mineralisation. Weights of evidence modeling techniques were used to determine spatial correlations between porphyry Cu-Au mines and predictive maps created from available spatial data. These predictive maps were then combined into a final prospectivity map. Despite limited regional scale data the model has successfully identified areas of known porphyry mineralisation as prospective and has also identified areas where new mineralised systems may be discovered with further exploration. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008