Search Documents

By A. Chieregati

"A heterogeneity study was conducted at Erdenet Copper Mine in Erdenet, Mongolia, to determine the fundamental sampling error associated with blasthole sampling. Using a custom-designed radial sector sampler , six large blasthole samples were collected to perform the test developed by Pierre Gy to estimate the constitutional heterogeneity factor for several types of ore. The study investigated the entire sampling protocol, from mine site to analytical laboratory, and quantified the contributions to total fundamental sampling error (FSE) of the various stages of sampling and sample preparation. The total relative standard deviation (RSD) of sampling error was determined to be ±32 percent and ±49 percent for copper and molybdenum, respectively. A classical statistical analysis conducted on the data confirmed the level of RSD native to the mine. About 95 percent of the sampling error was produced from one step in the sampling protocol, that of reducing the 1-kg (2.2-lb) sample to a 50-g (0.1-lb) sample for chemical analysis. To minimize the FSE, the use of a slightly different protocol is recommended. The 1-kg sample (2.2-lb) should first be crushed to a 0.2 cm (0.08 in.) particle size. A 250-g (0.5-lb) split should then be taken and finely ground, from which a 50-g (0.1-lb) split should then be taken. These simple steps will reduce the FSE to ±7.9 percent and ±17 percent for copper and molybdenum, respectively. The modified sampling protocol effectively reduces to zero the probability of misclassification of low-grade ore. IntroductionThe Erdenet copper-molybdenumopenpit mine is located in Erdenet in Orkhon province, Mongolia. The Erdenetiin-Ovoo copper-molybdenum deposit is 1.5 to 3 km (0.9 to 1.8 miles) wide and about 25 km (16 miles) long (Erdenet Mining Corp., 2016). Chalcopyrite, bornite covellite and chalcocite are among the major minerals found in the deposit. The mine processes approximately 26 Mt/a (29 million stpy) of ore."

Jan 11, 2017

By C. Newman, N. Schaefer

"As underground mining continues to operate at deeper depths and in more complex geologic and geometric conditions, there has been an increased demand for mine designs to better reflect site-specific conditions, measurements, and observations with respect to ground control safety and stability. During the past 20 years, the National Institute for Occupational Safety and Health (NIOSH) has developed, validated and distributed a number of free software packages (ALPS, ARMPS, AMSS, ARBS, etc.) specifically aimed at providing the industry with ground control design tools for the evaluation of underground stability in coal mines. While these programs were initially developed as stand-alone software packages where all data reside on an individual or workgroup computer, modern day web applications have begun to migrate toward a “multiple-tier” architecture, allowing multiple users to access an application by means of an Internet connection.This article introduces a new Web-based platform for ground control software applications, webGroundControl (webGC). webGC provides users with a platform through which one can access NIOSH and other ground control design software utilizing a Webbased, multiple-tier architecture. This provides users with easy access to ground control designs, the ability to perform on-demand calculations, as well as increase online collaboration between operational personnel and engineers through a web server. The basic framework and, more specifically, the user-interface of webGC are defined and outlined within this paper. It is expected that the mining industry will rapidly embrace this new product and webGroundControl will be a new paradigm for mining engineering computer applications. Platform architectureAs Web-based computing technologies continue to advance and cloud computing gains momentum, web-based platforms for software applications are growing in popularity across all industries due to ease of product accessibility and distribution as well as data security. With the expansion of Internet connectivity on the surface and underground, there is an industry need to develop Internet-based applications for mine and ground control design (Barczak et al., 2016). Cloud-based products are already available for many industries and are slowly being developed for the mining and geotechnical industry. A notable example is the drillysis package, which is a cloud-based borehole logging database (Geosysta, 2017) or the Dynonobel package for on the fly blasting calculations (Dyno Nobel, 2013)."

Jan 10, 2017

"A long-term mine production schedule optimization based on stochastic integer programming is presented that manages the risk due to geological variability and uncertainty while jointly considering mine profitability, truck fleet requirements and waste management. The evolution of the pit is controlled so that space within the mined-out pit is continuously provided to allow for tailings and waste rock to be replaced, thus minimizing the project’s environmental footprint. The method is applied at a taconite iron ore deposit and has a project net present value that is 16.9 percent higher than that of a conventional schedule and has a higher chance of meeting production forecasts. The stochastic schedule reduces equipment requirements by delaying waste mining and by mining selectively in order to meet plant ore feed requirements without stockpiling material, resulting in 23.7 and 26.2 percent lower mining capital and operating costs, respectively. IntroductionThe LabMag iron ore deposit is part of the Millennium Iron Range, a 210-km (130-mile) belt of taconite in northern Quebec and Labrador, Canada. LabMag has significant economic potential. It contains more than 3.3 Gt (3.6 billion st) of proven reserves at an average total iron content of 29.8 percent and is very low in impurities. However, on a project basis of 23 Mt/a (25 million stpy) of product, the required capital expenditure is estimated at more than $5 billion (SNC-Lavalin, 2014), which necessitates careful evaluation of all sources of risk. Resource estimation is one of the main sources of risk in a mining project as knowledge of the orebody is primarily based on drilling, which is often sparse because it is expensive. If the expected ore tonnages and qualities are not obtained when mining, the project cash flows are directly affected. The expected quantities and qualities of ore and waste are defined by the mine production schedule, which specifies the sequence of extraction and is dependent on the resource estimation. The goal of mine production scheduling is thus to maximize the expected profit, while also meeting all production targets and constraints, by creating an extraction schedule that is robust in the face of geological risk and has the highest chance possible of actually being realized."

Jan 10, 2017

"The 35th Annual American Mining Hall of Fame Awards Banquet and Fundraiser, sponsored by the Mining Foundation of the Southwest (MFSW), will be held at the JW Marriott Tucson Starr Pass Resort & Spa on Saturday, Dec. 2, 2017. This year, the Foundation will honor one living Hall of Fame inductee, two Medal of Merit recipients, four honorees from Mining’s Past and an Industry Partner for their respective contributions to the mining industry.Gary J. Goldberg will be the 2017 Hall of Fame Inductee and will serve as the keynote speaker at the awards banquet. Goldberg was appointed president and chief executive officer and joined the board of directors of Newmont Mining Corp. in March 2013. Prior to this appointment, he served numerous companies in key positions including Rio Tinto Minerals, US Borax and Coal & Allied Industries. At every appointment, he was able to improve safety concerns and reduce injury rates. While serving as chairman of the National Mining Association, Goldberg launched the CORESafety initiative and US Borax was the first mining company to receive the California Governor’s Environmental and Economic Award.The Medal of Merit will be awarded to John C. Lacy, a shareholder of DeConcini McDonald Yetwin & Lacy, P.C. and a director of the Global Law Center at the University of Arizona’s Law School. Lacy’s law practice concentrates on mining and public land law and encompasses transactional and title consideration involving acquisition of mineral rights. He played a crucial role in the revisions to the mining law of the Republic of Bolivia and the English translation of the mining laws and regulations of Mexico. Lacy’s expertise in mining law impelled the University of Arizona James E. Rogers College of Law to approach him to head the new Global Mining Law Center in 2015. The program now partners with the Lowell Institute for Mineral Resources and offers cross-listing of courses"

Jan 10, 2017

By K. C. Kocsis

"Diesel-powered equipment has allowed the mining industry to raise production rates and significantly improve productivity, as it is rugged, mobile and reliable, but its widespread use in underground mines has generated concerns regarding the exposure of mine workers to harmful diesel engine exhaust gases and particulate components such as diesel particulate matter (DPM), which has recently been classified as a human carcinogen by the International Agency for Research on Cancer. The agency expressed further concerns that workers’ exposure to high DPM concentrations can increase the risk of cardiovascular, cardiopulmonary and respiratory illnesses. Three emerging technologies could have the ability to replace dieselpowered equipment and remove DPM from underground mines: fuel-cell-powered mining equipment, battery-powered mining equipment and advanced material handling systems. This paper reviews them and assesses whether they have reached the point where the pollutants emitted by diesel-powered equipment can be removed from underground mines through the introduction of zero-emission mining equipment and power systems. Information is also provided from the results of a feasibility study, including a detailed cost benefit analysis, carried out at six Canadian and nine U.S. underground mines, which looked at the possibility of replacing diesel-powered production equipment with fuel-cell-powered equipment. The remarkable pace at which battery technology is progressing is also reviewed, and the feasibility of replacing diesel-powered mining equipment with battery-powered equipment is assessed. IntroductionHazardous pollutants in underground mines. Why is it important to remove diesel particulate matter (DPM) from underground mines? Over the past 40 years, diesel-powered equipment has allowed the mining industry to achieve rising production rates and major improvements in productivity, as the diesel engine is an economical source of power and diesel-powered equipment is usually rugged, mobile and reliable. On the negative side, the toxicity of some diesel exhaust gases is well known (Grenier et al., 2001), and the widespread use of diesel-powered equipment in underground mines has generated increasing concerns about the occupational exposure of mine workers to harmful diesel engine exhaust gases and particulate components such as DPM. Diesel equipment also entails other hazards like heat and humidity. Exposure to excessive heat can cause heat illnesses, such as heat rash, heat exhaustion and heat stroke (Donoghue, 2004; Roghanchi et al., 2016), and a hot and humid underground environment negatively affects the efficiency of the workforce, which may result in a decline in production output (Roghanchi et al., 2017)."

Jan 10, 2017

By Jay R. Schafler, Jacob L. Brinkman, Catherine E. Johnson

"The United States coal mining industry is currently experiencing a decline in both demand and commodity price while facing implementation of more stringent air and water pollution regulations. Company profits have decreased significantly, forcing several major companies to declare bankruptcy. The industry was required to adapt to survive. Many of these companies have adjusted by abandoning mines; the last two decades have seen a drastic decrease in the number of mines. To discover the primary causes of this downturn, three major aspects must be studied: properties of abandoned mines, commodity history and regulatory impact. Trends since 1994Each year, U.S. coal mines are required to submit data on a variety of categories to the U.S. Mine Safety and Health Administration (MSHA) and the U.S. Energy Information Administration (EIA). This data include administrative records, production values and information regarding the attributes of the mined material and the mine itself. Each year since 1996, EIA has released a report summarizing the data from two years prior. Additionally, MSHA maintains a database containing a collection of all the most current data. These resources are the primary sources for the figures included in this article. There are several items to note regarding this data:1. The EIA reports from 2016 and 2017 were not released at the time of writing this report.2. The MSHA data set is actively maintained as information is provided. This means the data for 2016 is from June 27, 2016 and data for 2017 is from Aug 24, 2017. All other points represent the end of-year values.3. Each of the figures only includes data pertaining to active mines. EIA defines active mines as both active and temporarily idled mines, and inactive mines as nonproducing and abandoned mines. MSHA separates all four into separate categories, though this paper combines the MSHA values according to the EIA definition for the purpose of comparison."

Jan 10, 2017

By Steve Karl

"The global underground construction and tunneling industry is in pretty good shape. Billions are being spent in shoring up aging infrastructure in the United States and other places, and new underground projects are being put out for bid.With each new project, comes new equipment, technology and tunneling methods. So it is incumbent on tunneling professionals to constantly improve their knowledge of the profession. This is where spending a few days with other underground construction professionals can assist the tunneler in keeping up.Every two years, tunnelers and underground construction engineers, contractors, suppliers, designers and owners from around the world gather for the Rapid Excavation Tunneling Congress (RETC). The 2017 conference was held in June in San Diego, CA. The UCA of SME puts on the conference.This years’ RETC attracted 1,400 attendees. The accompanying sold-out exhibit totaled 188 service and equipment suppliers. In addition, the conference had the UCA of SME bookstore, where the new History of Tunneling in the United States book was introduced. And a short course on tunnel rehabilitation was featured.Technical programmingRETC 2017 featured nearly 100 technical presentations. Topics covered the breadth of the global underground construction industry. Here is a sampling of a few. The proceedings from the conference is available from SME, 303-948-4200, www.smenet.org.Accomplishing extraordinary tasks as a machine supplier for Metro Doha: The construction of the Metro Doha in the State of Qatar established a modern, safe, efficient and integrated public transportation network. Upon final completion of multiple phases, the network will comprise four metro lines with a length of 216 km (83 miles) and 100 stations. Phase one comprises 112 km (43 miles of underground tunnels (56 km or 22 miles of twin-tube tunnels). Twenty-one earth pressure balance tunnel boring machines (TBM) were deployed by the four different joint ventures. The project was initiated, managed and supervised by the owner, Transport Authority Qatar Rail.Phase two of the Doha Metro will start upon the completion of Phase One in 2019 (Qatar Vision 2030). The owner placed full faith in the manufacturer’s abilities to deliver equipment of high quality, state of the art standards within the given time frame. This paper focused on the manufacturer’s scope of delivery and on the supplier’s high standards of quality in production, logistics and services."

Jan 9, 2017

By Justin Carl, Aliuddin Mohammad, Gordon Evans, Steven Bealby, Carlton Ray

"The District of Columbia Water and Sewer Authority (DC Water) is implementing the $2.2-billion DC Clean Rivers Project (DCCR) to control combined sewer overflows (CSO) to the Anacostia and Potomac rivers and Rock Creek, and to provide flood relief to the Bloomingdale and LeDroit Park neighborhoods in the District of Columbia. The long-term control plan complies with the requirements of a Federal Consent Decree entered into by DC Water, the District of Columbia and the United States, as represented by the U.S. Environmental Protection Agency and the Department of Justice. The Northeast Boundary Tunnel, a design-build project, will store combined sewage and deliver it to a system of downstream tunnels and ultimately to the Blue Plains Advanced Wastewater Treatment Plant (Blue Plains), where it will be treated. In addition, the Northeast Boundary Tunnel (NEBT) is a major project associated with the mayor’s task force to alleviate extreme flood events in Bloomingdale and LeDroit Park. The Northeast Boundary Tunnel Utility Relocations (NEBTUR) design-bid-build (DBB) project is an accelerated component of the Anacostia River System, as shown in Fig. 1. During dry weather conditions, the entirety of the sewage in the combined system is conveyed to Blue Plains.During storm events, when sewer pipe capacity is exceeded, the flow, which is a mixture of sewage and stormwater runoff, overflows into receiving waters through outfalls. There are a total of 47 active CSO outfalls along district waterways.The influx of storm runoff into the combined sewer has an additional impact on the communities of Bloomingdale and LeDroit Park. The sewer system is outdated and undersized. In these neighborhoods, when the capacity of the sewer is exceeded, localized flooding occurs and backups into adjacent residences are prevalent. In any given year, there is a 50-percent chance that flooding will occur in these neighborhoods."

Jan 9, 2017

By Ralph van Rijswick, Erik Vlot

"Anglo American operates 18 Weir GEHO piston diaphragm pumps (PD) in the two pump stations of the 52-km (32-mile) long Minas Rio iron ore concentrate pipeline. The pipeline is designed to transport 26.5 Mt/a (29.2 million stpy) of concentrate from the mine to the export terminal at the coast.During the commissioning of the pipeline in the fall of 2014, high pressure pulsation levels were experienced, with peak-to-peak levels as high as 20 bar. Based on pressure readings it was concluded that hydraulic resonances were present in the system, which were excited by the third and sixth harmonic of the flow pulsation generated by the pumps.Based on this observation, Weir Minerals Netherlands, manufacturer of GEHO PD slurry pumps, recommended installing a phase shift controller that controls the phase shift between the crankshafts of the individual pumps, thereby minimizing the effect of the hydraulic resonances.GEHO piston diaphragm pumps and pressure pulsation analysisPiston diaphragm pumps are used worldwide to transport abrasive and/or aggressive slurries against high discharge pressures in the mining, mineral processing and power industries. The basic operating principle of a piston diaphragm pump is shown in Fig. 1.A crankshaft is driven by an external electric motor via a gearbox. The crank mechanism transfers the rotating motion of the crankshaft into a reciprocating motion of the piston. The piston displaces a hydraulic fluid, called the propeling liquid, which displaces an elastic rubber diaphragm. When the piston moves to the right, the pressure in the pump chamber drops below the suction pressure and the nonreturn valve on the suction side will open, allowing the pumped fluid to flow into the pump chamber. When the piston moves to the left, the fluid is compressed, and when the pump chamber pressure rises above the pipeline pressure, the nonreturn valve on the discharge side will open allowing a displacement of fluid into the discharge line. The main objective of the diaphragm is to isolate the piston and the drive mechanism from the abrasive and/or aggressive fluid and create a hermetic seal between the pumped fluid and the ambient environment. Piston diaphragm pumps as shown in Fig. 1 are among the largest positive displacement pumps in the world and have been produced with stroke volumes of up to 100 L (26 gal) per pump chamber for flow rates up to 800 m3/h, discharge pressures up to 250 bar and hydraulic outputs over 2 MW per unit (van Rijswick et al., 2010)."

Jan 9, 2017

By M. Sunkpal, K. C. Kocsis

"An underground environment with high air temperature and humidity conditions generated from various heat and moisture sources can significantly affect the thermoregulation processes of the human body. This can lead to a series of heat-related illnesses such as heat exhaustion, heat cramps and heat stroke. The majority of the metabolic energy of a mine worker results in the production of heat. If the human body is to maintain thermal equilibrium, then this metabolic heat must be transferred to the ambient surroundings at the same rate. The heat loss from the human body occurs through a combination of heat transfer processes, such as respiratory heat exchange, convection, radiation and evaporation. If the heat loss from the human body to the ambient surroundings is less than the metabolic heat produced, the excess will be accumulated within the human body, which will result in a rise in the core and skin temperatures. This can ultimately lead to a heat-related illness or a combination of heat-related illnesses. This paper aims to discuss major heat-related issues and provide an overview of various mine ventilation and cooling systems, which can be employed to overcome high levels of heat and humidity in underground mines. In this paper, the effects of heat exposure on the health, safety and productivity of the mine workers are also highlighted. IntroductionMining in the United States remains one of the most hazardous industries, despite significant reductions in fatal injuries over the last century (Coleman and Kerkering, 2007; Saleh and Cummings 2011; Jacklitsch, Musolin and Kim, 2016). Occupational health hazards within the mining industry include hazards that are physical, such as traumatic injury or hearing loss; chemical, such as silica or diesel particulate matter; biological; ergonomic; and psychological (Donoghue, 2004; Saleh and Cummings, 2011). The effects of some of these hazards can be diagnosed immediately, while many, like black-lung and silicosis, will have long-term effects on the health, safety and life quality of mine workers (Donoghue, 2004; National Institute for Occupational Safety and Health, NIOSH, 2000). Among these hazards, exposure to heat and humidity can significantly affect the safety, health and productivity of mine workers, particularly in deep and hot underground mines (Roghanchi, Sunkpal and Kocsis, 2015). Short-term acute heat exposures can cause a rise in the core temperature of the human body, which can result in a heat-related illness or combination of heat-related illnesses. Adverse long-term chronic heat exposure can generate serious occupational heat-related illnesses, such as cardiovascular diseases, mental health problems and chronic kidney diseases. High core body temperatures coupled with dehydration can generate negative behavioral effects such as physical fatigue, irritability, lethargy, impaired judgment, loss of dexterity and loss of concentration (Xiang et al., 2014)"

Jan 9, 2017

By William Gleason

"Once the primary fuel source for the United States and the economic backbone for communities from Appalachia to Wyoming, coal has been on a steady decline since the mid 1990s, and is now at the center of political debate in the United States.The political spectrum of the United States is divided on the future of coal and its place in the energy sector. The coal mining industry and the communities that rely on coal have increasingly been pitted against forces that wish to regulate coal to the history books.In 2008, President Obama launched what many have called his war on coal, and during his eight years in office, he pushed through numerous pieces of regulations and legislation and that he said were aimed at reducing carbon emissions, but that others viewed as direct assaults on the domestic coal industry. Obama led the United States delegation to Paris to sign the Paris Accord in 2016, a 196-country agreement pledging that the United States would do its part to reduce carbon emissions. His administration also instituted clean air, power and water regulations that added extra environmental burdens to many industries, but perhaps none more so than the coal industry.In this month’s lead feature, “A study of U.S. coal mine closures since 1994” (page 18), the impact of the war on coal, and other factors, can be seen in text and figures. Author Jacob Brinkman and coauthors Jay Schafler and Catherine Johnson scoured the data of the U.S. Energy Information Administration (EIA) and the U.S. Mine Safety and Health Administration (MSHA) to show how coal production and mines have been impacted since 1994 and how the years 1994 to 2000 and 2008 to 2016 were particularly hard on the industry.For example, in 1994 there were 2,354 coal mines in the United States. Currently, there are 1,035 mines in operation.In 2016, then candidate Donald Trump promised to end the war on coal and to put coal miners back to work. In 2017, President Trump has followed up on those promises. He announced plans to withdraw the United States from the Paris Accord, signed an executive order designed to undo the Clean Power Plan put in place by President Obama, halted the research on the health effects of mountaintop removal coal mining, directed the U.S. Environmental Protection Agency (EPA) to revise the guidelines of waste water from power plants and has touted that more than 1,000 coal miners have returned to work since he was elected."

Jan 9, 2017

By Mike Lewis

"Descending several stories down a metal staircase into a shaft spanning a quarter city block -- soon to become Roosevelt Light Rail Station in Seattle, WA -- visitors are greeted with four perfectly round, precast concrete-lined horizontal holes leading deep into the earth. The sound of water trickling out from a small drainage trough can be heard over the faint echoes of construction within. Upon entering, the light is dim, but the air is clear with barely a dust particle flowing through the sunbeams. This type of air quality is only accomplished with diligent controls, and JCM Northlink, the company in charge of building the Northgate Link Extension Project, is taking those measures seriously.Commissioned by Sound Transit, JCM is a joint venture of three companies: Jay Dee Contractors, Frank Coluccio Construction Co. and Michels Corp. The tunnels JCM constructed are intended to provide fast, reliable underground rail service, as well as relieve one of the region’s most congested traffic areas. The $440 million project will connect the Northgate, Roosevelt and University District neighborhoods north of Seattle to the downtown corridor and SeaTac airport further south.The scope of this project includes excavation for two light rail stations, boring of two parallel 5 km- (3.3-mile) long light rail tunnels in six runs and the construction of 23 cross passages. Begun in 2014, Sound Transit estimates that crews excavated more than 382,000 m3 (500,000 cu yds) of soil and installed 7,352 precast concrete tunnel liner rings during the shaft construction and boring phase. Now that tunnel boring is complete, JCM is in the process of constructing the cross passages, which act as maintenance areas and escape routes for passengers. Throughout the entire process, the company has utilized atomized mist to control particle emissions.“Our dust control needs change at every phase of the project and don’t go away until the project is fully complete,” said a JCM safety representative. “We found that different dust suppression technologies were needed at different intervals, but atomized mist seemed to fulfill our needs at every step.”"

Jan 9, 2017

By A. G. Yapo, T. W. Camm

"Mining plays a key role in the development of modern civilization as a source of essential raw materials and provider of essential fuels, producer of jobs and a factor in support of the international balance of monetary payment (Camm, 2014). Professionals in mining locate, develop, design and manage ore deposits in an environmentally safe and profitable manner. As mineral deposits become increasingly scarce, new challenges face the industry. A current trend is to an increased emphasis on underground mining techniques for deeper deposits. Operations are safer now than before as companies understand better their work environment and the importance of mining responsibly.A continual challenge for the industry is accurately reflecting the costs and selling price of ore. An enduring characteristic of mining is the situation where the market typically determines the price of a commodity; the main control a company has on the bottom line is to control the cost of production.An attempt to bring light and clarity to the cost of their business will give a better idea to investors on the true profitability of the mining business. Gold producers face this struggle to accurately reflect the cost of production while also seeking to attract the interest of the investment community (Hill, 2013). In order to have a consistent format to report on their production costs, leading gold producers, through their alliance inside the World Gold Council (WGC), worked on the adoption of a new cost framework: the all-in sustaining cost (AISC) and all-in cost (AIC).Since 1996, the traditional cash cost reporting has focused only on the mining and processing costs incurred in mining an ounce of gold, which included the costs of goods sold (labor, energy, and consumables costs) and royalties (Table 1). But cash cost reporting ignores many important aspects, like sustaining capital, general and administrative expenses and site rehabilitation at the end of the mine life (Whelan, 2013). The cash cost was used to attract many investors into the business. In fact, the high gross margin (sales minus cash costs) has been promoted in past decades by the industry instead of the net or operating margin. As a result, even when the gold price was high, nearly $61/g ($1,900/oz) in August 2011, gold producers were not reporting excessive profits in their cash flow/income statements, to the disappointment and incomprehension of investors (Milstead, 2014). The truth was simply that the other costs omitted in the traditional cash cost were reducing the apparent profits.The disconnect led to a need for more accurate cost reporting in order to win back investor confidence and provide better understanding of gold mining economics. In 2012, the senior gold mining companies, including Gold Fields, Barrick Gold Corp. and Newmont Mining Corp., worked with the WGC to develop a new measure. This resulted in the June 2013 publication of the new framework AISC and AIC, which has been widely embraced by the sector since Jan. 1, 2014 (WGC, 2013).The adoption of the new cost template would have the dilemma of showing the real profitability of gold mine properties, which might alleviate taxes from governments and legislators, but it might also scare off investors toward more lucrative industries if not winning back their confidence."

Jan 9, 2017

"The National Mining Hall of Fame and Museum (NMHFM) announced the 2017 National Mining Hall of Fame inductees. This year’s inductees, selected by the National Mining Hall of Fame’s Board of Governors, represent exploration and extraction of new frontiers, environmental stewardship, leadership in formulating U.S. mineral policy, education, and research and development, including the use of computers in planning, designing and managing mineral industry operations. The contributions of these individuals have undoubtedly had a significant and lasting impact on the mineral and mining industry. These individuals were selected for being visionary leaders, innovators, authors, pioneers in corporate social responsibility, and long-standing advocates for the U.S. mining industry.Dr. Thomas V. Falkie, Leonard Harris, Dr. Vincent E. McKelvey, and Gordon R. Parker will join 236 other mining industry luminaries when formally inducted into the National Mining Hall of Fame on Sept. 23, 2017. The 30th Annual Induction Banquet and Ceremony will be held at the Pinnacle Club, Grand Hyatt Hotel in Denver, CO.2017 National Mining Hall of Fame inductees:Dr. Thomas V. Falkie — In a career spanning six decades, Falkie’s accomplishments in industry, academia, government and professional societies demonstrate a pattern of integrity and sustained excellence. His gravitas and management style left highly favorable impressions in every position he held. He was the chairman and president of Berwind Natural Resources Corp.; President of SME; President of the American Institute of Mining, Metallurgy and Petroleum Engineers; Director of the U.S. Bureau of Mines and head of the Department of Mineral Engineering at the Pennsylvania State University. He played major leadership roles in the American Mining Congress, National Coal Association, Mining and Metallurgical Society of America, and the National Mining Association. He served on the board of directors of Foote Minerals and Cyprus-Amax and was very active in the National Academy of Engineering, the SME Foundation and the National Mining Hall of Fame and Museum.Leonard Harris — A highly regarded metallurgist and business executive, Leonard (Len) Harris may be most remembered for the heart he has for the people whose lives were touched by his career. For more than six decades, Harris has been a true pioneer in corporate social responsibility, leading companies to understand that doing the right thing for the local people is also the best path to business success. After an early career in Australia and Ghana, Harris moved to Peru in 1955 to join Cerro de Pasco Corp., owner of several mines with one of the most complex metallurgical operations in the world. Harris was quickly promoted through multiple positions and was ultimately named director of metallurgy."

Jan 8, 2017

By C. Roos

"Mining companies have included quantifying uncertainty, or at least risk, as a requirement of project justification for many years. However, many times this process lags behind the traditional mine planning process and the results are rarely used to improve the plan. Nearly every parameter used in a mine plan is an estimate and the mine planning engineer should recognize, and even embrace, the inherent uncertainty in those parameters and its effect on their forecast results. While many of the uncertainties are beyond the scope of the traditional mine plan (e.g. global market uncertainty, socio-political uncertainty, environmental uncertainty), some uncertainties can, and should, be included in the mine planning process.Many mining engineers have incorporated techniques such as Monte Carlo Simulation or Discrete Element Simulation to understand the range of productivity that can be expected for an operation, but most still rely upon one estimated model for what is likely the critical component of technical uncertainty, the geologic resource. Modern geostatistical methods can provide multiple orebody realizations to provide a thorough unbiased picture of the geologic uncertainty. However, most traditional mine planning techniques are not formulated to allow for multiple (100-200) realizations of each material quality/grade parameter.Commercial software companies and research groups are progressing with development of tools that can incorporate geologic uncertainty, and even optimize extraction plans in the uncertain environment. Unfortunately, this author believes that a significant number of mining operations will not be able to adopt these techniques due to the computational requirements of the advanced techniques and the costs associated with implementing proprietary software. In an attempt to encourage mining engineers to embrace the inherent uncertainty in their mine plans, this article presents a cost-effective alternative that can be developed in-house, at any mine, to schedule mid- to long-term mine plans while continuously monitoring the uncertainty in the results. The aim of this article is that by demonstrating the usefulness of such a system, mining companies will encourage engineers, geologists and geostatisticians to find ways to incorporate this powerful data into their processes and procedures."

Jan 8, 2017

By Douglas B. Silver

"Editor’s note: Douglas B. Silver, Portfolio Manager, Orion Resource Partners, was the keynote speaker at the 2017 SME Annual Conference & Expo in Denver, CO on Feb. 19, 2017. He also gave the keynote address to the SME Annual Conference in 2008. The following is his 2017 keynote address with a few of the slides that were presented. The full speech is available on YouTube https://www.youtube. com/watch?v=uF0qwGJIX3UIn 2008, I had the privilege of giving SME’s keynote address. At that time the financial markets were on the verge of collapse and my presentation described the issues. Unfortunately I was correct, and global markets went into a steep nosedive, creating the largest economic downturn since the Great Depression.In hindsight, there were plenty of signs that this was coming. The Supercycle had created massive new wealth. This wealth was largely invested in the United States due to the country’s political stability and credit worthiness. In 2004, the large investment banks convinced the U.S. Securities Exchange Commission (SEC) to allow them to triple their borrowing leverage ratios. This made the banks more vulnerable to market volatility. The banks then lent money to NINJAS - people with no income, no job and no assets. Even worse was the fact that these unqualified home owners used adjusted-rate mortgages (ARMs) which they, of course, intended to refinance prior to interest rates rising. These mortgages were then bundled up by the banks and sold to investors as “safe” investment products. The money flowed into these products because the rating agencies gave these instruments high marks. These same agencies earned their fees from the very same banks seeking high ratings. (No conflict there). Private debt exploded and peaked out in 2008.These mortgage products were sold in an unregulated shadow banking system and the ARMs came due. Toxic mortgage default rates skyrocketed and the mortgage-backed securities collapsed in value. This house of cards had a negative feedback loop that accelerated the market crash and resulted in more than $1.5 trillion being lost in the securitization sector, a 47 percent decline in the Dow Jones Industrial Average, foreclosure rates skyrocketing and housing prices collapsing. The financial markets were in a nosedive."

Jan 8, 2017

By D. Newman

Ground control is critical to the success of a safe and productive underground stone mining operation. The primary focus of the ground control engineer is the stability of the roof or back; development and benched pillar stability; stability of the sill pillar between vertically adjacent mining levels; and floor stability. Roof stability begins with the selection of a stable back horizon based on the presence of a thin shale parting, stylolite or other discontinuity from which the production shot can easily peel away, leaving a stable back stratum. Bed thickness, fracture spacing, jointing and the material properties of the roof strata control the room width; the decision whether to bolt the roof; the bolt length, type and diameter; and the spacing of the roof support. Horizontal stress controls the header and crosscut azimuth. The mine operator should avoid driving perpendicular to the maximum horizontal stress direction. Where this is unavoidable, narrowing the opening width, narrowing pillar centers, increasing the support density and using three-way intersections are alternatives to remediate shearing along the roof-rib interface. Stable pillar dimensions depend upon the interaction of the vertical stress resulting from overburden thickness and multiple-level interaction of overlying level or levels; the mining height during development and the final mining height after floor shots are taken during benching; the presence of faults, folds or joints passing through the pillar; and limestone lithology, recognizing that the presence of oolitic bands, shale partings, joints and bentonite beds creates zones of weakness that can destabilize an otherwise competent pillar. Floor stability is typically not a significant issue for underground stone mines because the bearing capacity of the stone typically exceeds the vertical pressure transferred through the pillar. However, floor heave can be a ground control issue where shale partings, moisture-sensitive strata, weak stone bands or horizontal stress is present. Roof stability and pillar stability problems can be initiated as the floor heave enables the pillar and roof to settle. To illustrate these ground control issues, this paper presents four case histories that are a mix of ground failures and successful mining. The focus is on the geotechnical data required for roof, pillar and floor design and stability analysis.

Jan 8, 2017

By Jack Bedder

"Editor’s note: We would like to thank those who make this annual issue possible. A special thank you goes out to the industrial minerals annual review editor, to the Industrial Minerals & Aggregates Division Technical Committee chair and vice chairs, and to the authors of the individual commodity profiles.Jim Norman, member SME, of Tetra Tech, is the industrial minerals annual review editor.Ebrahim K. Tarshizi, member SME, of Michigan Tech, is chair of the Industrial Minerals &Aggregates Division’s Technical Committee.The technical committee vice chairs include: • Hyunjung Kim, member SME, of Chonbuk National University, agricultural materials.• Xihui Yin, member SME, of Kemira, ceramics and refractory materials.• Nikhil Gupta, member SME, of Virginia Tech, chemical raw materials.• Jasson Giddens and Swadhin Saurabh, members SME, of Oil Dri Corp of America and Mill Creek Engineering, respectively, chemical raw materials.• Snehamoy Chatterjee, member SME, of the Michigan Tech.• LeDeana Roberts and Shubham Verma, members SME, of Imerys and U.S. Oil Sands, respectively, fillers and pigments.• Thomas Hilderbrand and Kaiwu Huang, members SME, of Thiele Kaolin Co. and Virginia Tech, respectively, sorbents, filters and process aids.• Rhaghav Dubey and Edgar Blanco, members SME, of Outotec and FL Smidth, respectively, specialty mineralsAntimony generally occurs along with gold, lead, copper and silver. There are more than 100 antimony minerals, although the sulfide mineral stibnite is the main one.Antimony enters the supply chain either as a result of mining (primary production) or recycling (secondary production). China has by far the largest antimony resources and is, as a result, the world’s center for antimony mine production. In 2016, it accounted for more than three quarters of the global mine supply out of a world production figure of 130 kt (143,000 st), according to the U.S. Geological Survey. The biggest, and most high-grade deposits are found in southern China, with the largest mines located in Hunan, Guangxi and Yunnan provinces. Tajikistan, Russia, Australia and Bolivia are the largest mine producers outside China. A new antimony project in Oman made progress in 2016, producing first metal in April 2016 in test facilities, and then ordered three furnaces for a 26 kt/a (28,600 stpy) antimony metal and oxide smelter that is due on stream in late 2017.Antimony ingot production is not as widespread as is antimony mine production, owing to the high levels of pollution that are associated with antimony smelting. It is for this reason that smelting has been largely confined to China and other Asian countries, where environmental legislation is less stringent.Antimony oxide production is undertaken on four continents with China being the biggest producer. There is also a considerable amount of oxide production in Europe — which relies on imported feedstock, mostly from China. Antimony also enters the supply chain through recycling. Lead containing antimony is produced in a number of countries, mainly in secondary lead smelters. Typically, a blast furnace charge containing used or discarded battery plates, type metal or bearing metal is reduced to lead bullion, which is refined in reverberatory furnaces and melting pots. In the main, the antimony recovered is consumed in metallurgical applications. China was the biggest secondary antimony producer in 2016, and accounted for 25 retardants and lead-acid batteries. Flame retardants accounted for roughly 50 percent of consumption in 2016 with batteries representing about 25 percent. Other end uses include plastics and heat stabilizers, ceramics and glass and a variety of metallurgical applications. Demand has been sluggish since the global financial crisis, mostly because key markets failed to recover strongly from the downturn, particularly in Europe."

Jan 7, 2017

By Pierre Filiatreault, Brian Straight, Stephanie Thibeault, Devin Castendyk, Londie Cameron

"Working on or near water at active, closed or abandoned mine sites is inherently dangerous. Between 1996 and 1999, the U.S. Mine Safety and Health Administration (MSHA) reported 17 fatalities involving drowning at U.S. metal, non metal and coal mines (MSHA, 2000). Openpit mines which fill with water following mine closure, called pit lakes, present numerous risks to environmental monitoring teams including: a) drowning, b) hypothermia, c) falls to the ground from the top of high walls, d) collapse of unstable access roads, e) rock falls and avalanches from pit walls, f) avalanchegenerated tsunamis traveling across the lake surface and g) rapid degassing events.Some pit lakes are simply not safely or easily accessible for ongoing monitoring. However, the routine collection of water samples from the entire water column on a regular basis is needed to monitor the evolution of water quality over time, verify the accuracy of numerical predictions and, ultimately, manage lake water chemistry and ecological risks. For pit lakes with surface water discharge, regular monitoring is used to appropriately design and adjust water treatment plants in order to produce acceptable site discharge water quality.As a product of these risks and the need for water samples, mining companies spend considerable expense on pit lake safety as part of monitoring programs. This includes training personnel for on water duties and hazards, purchasing or hiring specialized equipment and personnel (such as boats, boat operators, personal floatation devices and cold-water clothing called mustang suits), stabilizing pit walls and maintaining safe access roads to the lake surface and employing spotters who can directly communicate with emergency medical services to watch sampling activities because cell phones and radio signals can be blocked by pit walls. Some sites utilize redundancy to prepare for unexpected incidents and accidents. For example, one Canadian mining company requires two boats on the water during pit lake sampling events, with a third boat on the shoreline, gassed and ready to go. In addition, water samplers are required to hold Marine Emergency Duties training to ensure the entire boat crew is sufficient and competent for the safe operation of the vessel in the event of an accident."

Jan 7, 2017

By T. Grammatikopoulos, C. Gibson, M. Aghamirian

"Lithium is a soft, silver-white alkali metal with atomic number 3. As of 2015, the end use of lithium was estimated to be as follows: lithium-ion batteries (35 percent), ceramics and glass (32 percent), lubricating greases (9 percent), air treatment (5 percent), continuous casting mould flux powders (5 percent), polymer production (4 percent), primary aluminum production (1 percent) and other uses (9 percent) (Jaskula, 2014). Lithium is found in brine lake deposits containing lithium chloride and in hard rock pegmatite deposits. It can be sold in a range of product types; as mineral concentrate, brine, compound (lithium carbonate or lithium hydroxide) and metal depending on its intended end use (Goonan, 2012; Jaskula 2014).In the 1990s, the United States and Chile were the largest producers of lithium globally, primarily from brine operations (Ober, 1994). Most of the lithium compounds produced during this period were consumed in the glass, ceramics and aluminum industries. In the 1980s and 1990s, there were two major lithium operations in the United States: brine operations at Silver Peak, NV and a spodumene mine and lithium carbonate/lithium hydroxide plant in Kings Mountain, NC. The Kings Mountain operations ceased production in 1991 and were eventually dismantled in 1994. Brine operations were also active in Argentina and Chile, while the largest lithium ore deposit in the world was operated at Greenbushes, Western Australia. During this period, it was predicted that major shifts in demand for lithium would come from the success and widespread use of electric vehicles (Ober, 1994).Lithium is still produced from the brine operations at Silver Peak. But in more recent years, Chile has become the world’s leading producer of lithium carbonate from brines. Australia has maintained its position as the world’s largest producer of lithium mineral concentrate, the majority of which is exported to China to produce lithium carbonate and lithium hydroxide (Jaskula, 2014).A spodumene concentrate was also produced at the Tanco Mine in Manitoba, Canada beginning in the 1980s through to 2010 when lithium operations were suspended due to fluctuations in the lithium market price (Martins et al., 2013)."

Jan 7, 2017