Search Documents

By Lok M. Sharma, Deep K. Khatri, Bradfield. Brett

"A shored enclosure was required to access a control structure upstream below the dam of a deep lake. The shoring involves the interaction of the structure, soil, and water and the loads imposed include the hydrostatic forces of the water, soil pressures as well as dynamic forces due to currents and waves. Deep excavation support systems have traditionally been designed using classical methods that involve direct computations of earth pressures. However, traditional analysis does not take into account soil-structure interaction. Numerical modelling offers better means to analyze soil-structure interaction. This paper presents a 2D finite element (2D-FE) analysis of a deep excavation support structure that was required to remove and replace a control structure at the upstream toe of a dam. The sheet-piling shoring was designed to withstand the lateral pressures from 14 m deep free water and 5.5 m deep excavation below the free water to reach the required excavation level to replace the gate structure. Elastic-plastic analyses were performed to predict the stresses and deformations of the complicated shoring structure and excavation bottom. The soil parameters, procedures used to develop the 2D-FE model, and the results are discussed in this paper. The shoring system is currently under construction.INTRODUCTIONA deep shoring system enclosure is required to keep out water and soil and to provide a support for unbalanced loadings due to dewatering and/or, excavation in order to permit construction of the permanent structures in the dry. A braced shoring system consists of a single wall sheet piling which is driven into the ground to form a “box” around the excavation site and is braced on the inside. After bracing the sheet piling, seal concrete is placed into the bottom to prevent water from seeping into the open excavation from underneath the sheet piling, and the water is pumped out to provide the dry work area. The braced shoring involves the interaction of the structure, soil, and water and the loads imposed include the hydrostatic forces of the water, soil pressures as well as dynamic forces due to currents and waves. Deep excavation support systems have traditionally been designed using classical methods that involve direct computations of earth pressures, (active, passive, or apparent pressures). There have been some uncertainties regarding the actual distribution of earth pressures due to influence of the support wall flexibility, as these traditional methods do not take into account soil-structure interaction. Numerical modelling offers better means to analyze soilstructure interaction."

Jan 1, 2017

By M. Kosugi, Y. Kon, M. Kawata, J. V. Satur, K. Mitsuhashi, C. Tokoro, K. Horiuchi, R. Kawarabuki, B. Calabia

"Liberation of copper minerals is important in ensuring high flotation efficiency in copper sulfide flotation. The high pressure grinding roll (HPGR), microwave (MW), and electric disintegration (ED) are known to feature enhanced liberation over conventional comminution machines such as jaw crushers and ball mills by producing internal stresses on minerals or mineral grain boundaries through high compressive forces, thermal expansion of minerals, and pulsed high voltage discharges, respectively. In this study, each of these methods was applied before ball mill grinding to investigate its effect on enhancing the liberation of copper minerals in a low grade and fine-grained copper ore. The copper minerals observed in the tested ore sample are bornite, chalcocite, and chalcopyrite, and their grain sizes range from 10 to over 100 µm. Calcite, quartz, and feldsparare confirmed as gangue minerals. The liberation of the copper minerals by the different methods was analyzed using the mineral liberation analyzer (MLA) and compared. The result showed that the HPGR crushing was the most effective for enhancing copper mineral liberation. HPGR bench-scale test was then conducted on the copper ore and flotation was applied on a HPGR-treated sample to confirm the improvement in the flotation performance by applying HPGR.INTRODUCTIONIn order to recover copper minerals by flotation, copper ore is usually ground by ball milling to liberate the copper minerals from gangue minerals. In the case that the fine size copper minerals are targeted, grinding of the copper ore to a finer size is necessary to increase the copper recovery. However, finer size grinding by ball mill increases energy consumption significantly, which might deteriorate the economies of the mineral processing operation. HPGR, MW, and ED have been recently the focus of researchers as new techniques for enhancing the mineral liberation in mineral processing (Tavares, 2004; Kingman, 1998; Wang, 2010).HPGR crushing is considered to generate micro cracks along mineral boundary when rocks pass between two rolls by applying high compressive force. In the MW treatment, micro cracks are reported to be generated at crystal boundaries by differential thermal expansion of crystals attached to each other. In the ED treatment, micro cracks are known to be produced by plasma current flowing along mineral grain boundaries. These treatments are expected to increase mineral liberation (Fujita, 2001),improve flotation performance(Michaelis, 2005), and reduce ball mill work index(Kaya, 2010)."

Jan 1, 2017

By John Mastoris, Kostis Dragasakis, Kostas Kouklidis, Shkurtë Gashi, Halil Berisha, Jenuz Bulica

Titan Group’s environmental policy and Sharrcem’s Corporate Social Responsibility (CSR) are the driving forces behind the development and implementation of a comprehensive Rehabilitation Plan at Dimce Quarry, which is the main raw material source for Sharrcem Cement Plant since the 1970’s, located in the municipality of Hani i Elezit in Kosovo. Based on an Environmental Impact Assessment Study and the approved Mining Plan and also on the principles prescribed in the Guidelines on Quarry Rehabilitation, released by the Cement Sustainability Initiative of the World Business Council for Sustainable Development (WBCSD-CSI), Sharrcem has adopted a quarry operation and rehabilitation process in line with the best practices in the mining and cement sector. This paper discusses the background for the development of the rehabilitation plan and the results of rehabilitation activities, as have been implemented over the last few years. The main objective of the progressive rehabilitation plan at Dimce Quarry is to restore the depleted pit and return it back to the original land owners for resettlement. To date approx. 3,4Ha of former mining area has been restored by backfilling and levelling of the depleted closed pit and returned back to owners, who have built their houses and turned it into a living area again. This Quarry has turned out to be a real composition and practical example of preserving and returning back the natural resources in a state compatible with the surrounding environment and with respect to the needs of the local stakeholders. The motivation for business to engage in rehabilitation activities in the first place lies in the belief that the development and implementation of a progressive and practical Quarry rehabilitation plan and restitution of the land will deliver significant environmental and social benefits that outweigh the long-term rehabilitation costs, while maintaining the company’s reputation.

Jan 1, 2017

"Foreword by Ren BryceSenior engineer, Freeport-McMoRan, Oro Valley, AZ, USAThe eighth annual Mineral & Metallurgical Processing Division (MPD) student poster contest was held in February at the national SME Annual Conference & Expo in Denver, CO. A total of 33 students presented their work at the poster competition. The competition started in January when the students submitted a one-page abstract for judging. In February, they prepared and presented a poster that explained their research. A panel of judges went to each student and listened as the students explained their research in five minutes.The students worked hard at their research and then set aside time to complete all the necessary steps to enter the competition. The MPD recognizes the effort required to enter and as a result, provides monetary rewards to all participants. The first-place winner receives $1,000; the second, $500; the third, $250; and the fourth through seventh, $200. All remaining students receive $100. All of the students also receive a complimentary ticket to the MPD Luncheon. As in past years, there are separate levels of competition for undergraduates and graduates.Graduate winnersKaustubh Shrimali won first place for researching “The influence of starch in amine adsorption by quartz in the reverse flotation of iron ore.” Venkata Atluri received second for studying “The effect of polysaccharides on bubble attachment at talc surfaces.” Jennifer Galvin placed third for investigating “A novel approach to alkali pug bake for the extraction of rare earth elements from monazite concentrate.” In the fourth through seventh places were Amy Richins, Sumedh Gostu, Brett Carlson and Chris Vass.Undergraduate winnersNestor Santa earned first place for exploring “Copper recovery from waste printed circuit boards.” Cassidy O’Connell received second place for conducting “Performance analysis of CMC in high talc copper sulfide flotation systems.” Catalina Vanegas won third place for examining “Cyanidation tests and pretreatments to recover gold from a refractory ore in Colombia.” Kylie Boyce, Michael Archambo and Pritam Sinha were in the fourth through sixth places.Everyone benefits from attending the student poster competition. The students are able to display their work to future employers, and industry professionals can talk to up-and-coming engineers. Next year, there will be another competition for more posters and networking. Come and enjoy the event and the posters."

Jan 1, 2017

By Filippo Maria Leoni, Gianluca Pianezze

"As part of the Southeast Louisiana (SELA) drainage program, designed to reduce flood damages in the City of New Orleans and surrounding parishes, the SELA-22 project entailed the construction of a concrete covered canal along Jefferson Ave. and Prytania Street. The scope of the required soil improvement was to replace the soil between two parallel lines of sheet piles with a soil-cement mass to eliminate under-seepage, thus creating a so called bottom plug, and provide structural support for the concrete box culvert. The U.S. Army Corps of Engineers (USACE), New Orleans District, selected the jet grouting technology for the construction of the bottom plug to a maximum depth of approximately 40 ft, and for a total length of approximately one mile. The specialty geotechnical contractor proposed to accomplish the task utilizing their proprietary and innovative elliptical bi-fluid jet grout technology which, by limiting the overlap between adjacent columns, allowed a reduction of the overall number of installations. Approximately 2,400 elliptical jet grout columns were installed in a very challenging environment, especially under a logistical point of view. This paper will summarize the main features of the project, focusing on the innovative technological solution adopted to maximize productivity and on the several challenges faced in such limited and complicated logistical conditions.INTRODUCTIONThe Southeast Louisiana (SELA) drainage program has been designed with the purpose of reducing flood damages in the City of New Orleans and surrounding parishes. This will be accomplished by constructing new pumping stations and better drainage canals throughout. The program was authorized in 1996 by the United States Congress and administered under a project cooperation agreement between the Sewerage and Water Board of New Orleans (SWBNO) and the USACE.Prompted by the severity of damages associated with rainfall flooding in southeast Louisiana, the SELA program consists of several individual project components. The proposed work is located on both the east and west banks of the Mississippi River in the Orleans and Jefferson Parishes, as well as in portion of St. Tammany Parish."

Jan 1, 2017

By M. Epiney, A. Ghahreman, R. Kim1and

"Pre-oxidation and cyanide leaching behavior of gold in the presence of sulfide minerals were reviewed, focused on the effects of oxygen injection in the gold leaching process. Generally, pre-oxidation and gold leaching kinetics from iron sulfide refractory minerals, such as pyrite, pyrrhotite, marcasite, pentlandite and arsenopyrite, can be enhanced with higher dissolved oxygen (DO) concentration. However, most of copper sulfide minerals dissolved well both in water and cyanide solutions, and copper from the minerals consumed DO and cyanide to oxidize and leach. Only in the presence of chalcopyrite, gold leaching was effectively occurred with increasing DO. However, chalcocite and covellite severely retarded gold leaching. Stibnite, an antimony mineral, formed a passive film on the gold surface under any DO conditions, and it slowed gold leaching. This impeding effect can be alleviated by leaching at low pH or adding lead salt. Using oxygen and lead together can make synergistic effect in oxidation of sulfide minerals and can enhance gold extraction. Depending on the mineralogical characteristics of the ore, the optimum DO and lead concentrations can be optimized. However, lead can cause environmental problems, and so its dosage should be minimized or eliminated by substituting it with oxygen injection.INTRODUCTIONGold ores containing sulfide minerals are becoming more significant as high grade gold oxide deposits are continuously becoming difficult to find. In light of this situation, to produce more gold, recovery methods from refractory gold ore containing various sulfide minerals should be investigated. Generally, sulfide minerals have impeding effects on gold leaching: formation of a passive film on the gold surface, high consumption of chemicalssuch as cyanide and oxygenduring leaching, reduction of gold cyanide by sulfide ions, etc. (Senanayake, 2008). Therefore, sulfides must be properly treated for better gold recovery. Pre-oxidation of sulfide minerals by injecting pure oxygen can decrease the impeding effects in gold leaching. Prior to cyanidation, sulfide minerals can be oxidized to metal hydroxide and sulfate form, which consume negligible cyanide in the following cyanidation circuit (Bodnaras et al., 1993). Moreover, gold cyanidation can be enhanced by increasing concentration of the dissolved oxygen (DO). In general, the optimum concentration ratio of [CN-]/[O2] is calculated as 6, but it goes higher in the real system (Marsden &House, 2006), which means that the reaction is typically controlled by DO concentration."

Jan 1, 2017

By Rimas Veitas, James Panton, Erich Steinlechner

"Ductile Iron Piles (DIPs) are a proven, viable alternative to conventional piles, and for the past five years have been successfully used throughout New England. The installation process of DIPs lends itself to both large and small projects. Because of their installation efficiency they provide a substantial cost savings over drilled micro piles. Several New England projects (both end bearing and friction) will be evaluated, focusing on the installation and design procedures.BackgroundThe driven ductile cast iron pile (DIP) is a simple, fast and highly effective pile system. Over the last 30 years over 10 million feet of this pile system has been installed worldwide predominantly in Europe. DIPs are a prefabricated driven pile system utilizing high strength ductile iron pipes which are manufactured using a spun-cast process having outside diameters of 4 5/8” and 6 5/8 inches. The standard pile lengths are 16.4 feet long. The pipes are manufactured with a tapered socket with an internal shoulder for full engagement at the top and a tapered spigot at the bottom. The individual pile sections can be connected with this Plug and Drive® connection to drive a pile of any length.(see figure 1)The DIP system’s inherent advantage is the simplicity of the installation process. The piles are driven to refusal or to a required penetration depth with the use of a high-impact highfrequency hydraulic hammer (ie. Breaker hammer). In most applications the hydraulic hammer is mounted on an appropriately sized excavator (see Photo 2). At the completion of driving the pile, the pile is cut off (see photo 5) and the remaining section of pile is fitted with the appropriate driving shoe and serves as the lead section for the next pile. Being able to reuse the cut off section, yields minimal if any pile shaft waste. The pile is then fitted with an appropriate pile cap plate to receive the load from the superstructure."

Jan 1, 2017

By Christopher Sammon, Nicholas Turus

"The demand for underground parking in South Florida has increased as a result of changes to the local building code, coupled with developers’ desire to improve building aesthetics and provide much needed walk in retail space for high-end structures. Historically, underground construction was uncommon in South Florida due to the high groundwater level and porous soil/rock. Conventional dewatering methods become ineffective only a short depth below the ground surface and deeper excavations have required a tremie seal solution consisting of wet excavation and the pouring a temporary unreinforced slab under a water head. However, as excavation area and depth increase, the cost and schedule of the tremie seal method become problematic. For these reasons developers and construction teams alike have looked to contractors in South Florida for alternative means of construction.This paper details the construction of two sites in South Florida where Deep Soil Mixing (DSM) technology offered an efficient alternative to tremie seal construction. The Brickell City Centre required excavation of 8 acres to depths of 30 feet, and augercast piles up to 36” diameter and 110 feet in depth. The second site, Jade Signature, required an excavation of up to 41 feet directly adjacent to the Atlantic beachfront. Due to the concerns over differential settlement, the project featured a soil mixed gravity wall that was designed and installed to allow for completion of the tower prior to excavating the adjacent garage.Both projects involved improving every square inch of ground beneath the planned project excavation. The developed DSM seal slab solution creates a nearly impervious excavation at excavation invert with the strength to resist hydrostatic uplift forces. Low permeability site perimeter walls are constructed to complete the sealed excavation and reinforced with either beams or sheet piles for structural support. Augercast piles required for the permanent hydrostatic concrete slab supplement the uplift capacity of the DSM. After DSM and augercast piles are installed from grade, the site is excavated in dry conditions."

Jan 1, 2017

By Nabil F. Ismael

"Load tests were carried out to examine the ultimate bearing capacity of short, large diameter bored piles in connection with the construction of a multistory building on the Arabian Gulf in Kuwait. Testing included 0.45 m, 1.0 m, and 1.2 m piles installed through loose sand into a bearing stratum consisting of very dense cemented sands. All tests were carried out to failure. The base resistance and shaft friction were calculated using the Meyerhof method for a layered soil profile. The method employs the standard penetration test N-values. The results indicate that the piles are end bearing piles with a great portion of the pile capacity due to base resistance. The mobilized skin friction is small. The calculated pile capacities were very close to the measured values with the maximum difference not exceeding 10%.INTRODUCTIONShort, large diameter bored piles are used with increasing frequency for heavy structures in Kuwait, and the Gulf region where ground conditions indicate loose deposits of calcareous sands. The piles range in length from 8 m to 15 m with their base located in the dense-to-very dense, cemented sand bearing deposit. The design of these piles requires knowledge of the skin friction and point resistance in these soils. While field tests on driven piles are available (Ismael 1989, Ismael 1999), field test data on large diameter bored piles installed through loose calcareous sands into dense-to-very dense cemented or partially cemented sands are very limited at present. The results of three load tests carried out recently on bored piles at one site in Kuwait have become available. In these tests the failure load was either reached or can be extrapolated from the test results. It is important to examine and analyze the test results for the benefit of the geotechnical research and design engineers.This paper presents the soil conditions, pile installation details, and the pile load test data at the test site located in Shuwaikh, Kuwait. The site is facing the Arabian Gulf. Test results were directly analyzed and the point resistance, and skin friction were calculated. The ultimate capacities of the piles were calculated and compared with the measured values. The influence of the pile diameter on the settlement at ultimate and at working loads is examined"

Jan 1, 2017

By Pathies Nawej Muteb, Tom Strombotne, Karl Leetmaa, Irma Gabric, Keith Darby

"Continuous control of the final grinding product size is important to optimize gold liberation for Gold Milling operations. At Meadowbank Mine an on-line Particle Size Monitor has been employed successfully to achieve the targeted final grind which leads to optimizing the gold recovery at maximum grinding circuit throughput. The live monitoring of the final product particle size leads to a maximum grinding circuit throughput every minute during the process. This paper discusses the optimal utilization of the Particle Size Monitor to assist the Mill operator to maximize the grinding circuit throughput as the milling conditions change due to variable ore processed at Meadowbank Mine. Also the paper includes the usage of the Particle Size Monitor to guarantee the final grind target at each instant of the process.IntroductionAgnico-Eagle is a Canadian-based company that Trades on the TSX & NYSE (AEM). It owns eight mines (8) operating in Nunavut, Quebec, Finland and Mexico and has more than 7,500 employees (Figure 1). 1.6 M ounces of gold were produced in 2015 and the annual average annual production from 2016 to 2018 is forecast to be approximately 1.53 million ounces of gold.The Meadowbank Mine is located in Nunavut, Canada (Figure 2). The mine opened in 2010 and from 2010 to 2014 a total of 1.8M oz of gold was produced. The milling rate is 4.2 Mt per year with an average mill throughput of 11,900 tpd or 496 tph. Average annual gold production over life of mine is expected to be 450,000 ounces. Meadowbank has 775 employees, of which 265 are Inuit or 36% of the total workforce. Estimated life of mine is 2010 to 2018. Gold production in 2015 was 381,804 oz. Meadowbank was Agnico-Eagle’s largest Gold producer in 2015."

Jan 1, 2017

By Jacob Miller, Phillip Mulligan

"Measuring the blast pressure associated with an explosion suspended above the ground (Free Air Burst)is a common research objective in Explosive Engineering. Theoretically, the shockwave from a Free Air Burst (FAB) configuration expands radially and the shockwave is assumed to have a smooth (uniform) shock front. The way in which the FAB explosive charge is suspended, packed, and the charge geometry can affect the shockwave expansion. These factors can generate a non-uniform shock front. As the scaled distance between the pressure sensor and the FAB increases, the shockwave expansion averagesnon-uniformities into a uniform shock front, at which point the FAB suspension system becomes less critical than when the scaled distance is “close-in” (Z <3)."

Jan 1, 2017

By T. Lupek, S. Plaum

"The execution of classical building services in underground mining operations is more truth than myth. From small concrete foundations for conveyor belts to the construction of huge workshops for large machinery maintenance, nearly every operation requires building services. By creating such fixed facilities, these services ensure the efficiency of the production. A distinction must be made between fixed facilities which directly enable the production and auxiliary facilities which only indirectly support the production. The construction costs of such auxiliary facilities are often roughly estimated because they do not immediately contribute to mineral extraction. The research project ‘Development of a systematic cost-calculation method for building services in underground mines’ seeks to address the question: ‘Can the construction costs concerning fixed auxiliary facilities be neglected e.g. within a prefeasibility study?’ The presentation will show the monetary relevance and significance of these auxiliary facilities and introduce a guideline for cost estimators. PROBLEM DEFINITION The overriding interest of an underground mining operator is to exploit the commodity with the maximal quality by minimum cost and time expenditure. If a new operation shall be installed, it has to promise profitability. Therefore, predictive economic feasibility studies are performed in advance of installation. Herein, all cost expenditure for installation and operation of the future underground mine is determined and compared to the expected income by selling the raw material. The described interest of the mining operator is the starting point of the research project ‘Development of a systematic cost-calculation method for building services in underground mines’. While economic feasibility studies for future operations are focused on the profitable exploitation of raw materials and the efficiency of the accompanying necessary production processes, auxiliary actions are only considered rudimentary. Necessary production processes, as well as auxiliary actions regularly require classical building services, which are normally performed in construction business on the surface in the same manner. By performing building services like masonry or concrete works in underground mines, fixed facilities shall be set up in order to enable or support the raw material production. Production enabling fixed facilities are varying from small concrete foundations for conveyor belts or other infrastructural elements to upstream processing plants situated in the mine workings. While such fixed facilities are essential parts of the production process chain, supporting facilities underground shall increase the efficiency of the mining operation. Workshops, control rooms and social installations are only a few examples for supporting facilities. Those could be situated on the surface as well, but the efficiency increases significantly by installing them underground. Especially supporting facilities are evading from the main interest of the mine operator, since they are only indirectly connected to the production process. The building costs are oftentimes only roughly assumed."

Jan 1, 2017

By Zihe Ren, Edouard Asselin, Marcus Tomlinson, Tianbi Zhang, Jing Liu

"Raman spectroscopy is used to quantify the extent of disorder in the carbonaceous matter associated with preg-robbing ores. Previous studies of Goldstrike ores showed that the height and width of the peaks for the “D” (disordered) and “G” (graphite) bands, the so-called “Raman ratio” had a strong correlation to the preg-robbing value (PRV) measured for various ore samples. A brief literature review on Raman spectroscopy as it applies to preg-robbing ores is presented. Further, recent studies, presented here, have shown no correlation between the Raman ratio and the PRV for a wide variety of ores. This suggests that the extent of organic carbon crystal disorder is not the main factor in determining preg-robbing characteristics.INTRODUCTION Preg-robbing may arise from natural carbonaceous materials in the ore. Several mechanisms have been proposed in the past decades including a physical sorption process by the carbonaceous matter, or via the reduction of aurocyanide at the mineral surface (Abotsi & Osseoasare, 1986; Afenya, Osseoasare, & Abotsi, 1983; Tan, Feng, Lukey, & Van Deventer, 2005). Nevertheless, the mechanisms of preg-robbing remain poorly understood. Understanding the nature of the preg-robber is of practical importance for the selection of a suitable treatment process. Fine carbon particles in the ore have been recognized as preg-robbers due to their similarity to the activated carbon used in the carbon in leach (CIL) or carbon in pulp (CIP) processes. Previous research has illustrated that the activated carbon (also referred to as amorphous carbon in some literature) has a much higher absorption ability than pure graphite with high crystallinity (Adams & Burger, 1998). Adams et al (Adams, Swaney, Friedl & Wagner 1996) concluded that carbonaceous matter is largely responsible for the overall preg-robbing capacity of a given ore. However, the mechanism of carbon preg-robbing was still not clear mostly due to the complexity of amorphous carbon and its behavior in different solution matrices, and at different pH and temperature (Adams, 1990, 1993)."

Jan 1, 2017

By D. Bahrami, G. Danko, W. Asante

"It is prudent to interpret atmospheric monitoring signals in real-time for checking the safe limits of the air conditions in underground mines. In gassy mines, such real-time evaluation increases the safety of operation. In all mines, the continuous monitoring and evaluation contribute to maintaining air conditions to be within healthy and safe limits. Signal interpretation for safety conditions in mines is difficult for many reasons. An increase of hazardous contaminant concentrations can be predicted by signal pattern recognition, root-cause analysis of rapid changes toward deterioration and forward prediction in time using algorithms and numerical models. This paper focuses on analyzing signal patterns to recognize dangerous trends as well as forward predicting the various environmental and working conditions that may affect safety in underground mines. Efficient numerical ventilation model with heat and gas contaminant simulation components is needed for the analysis of real-time atmospheric monitoring data. Computational speed enhancement methods are discussed and tested in numerical examples, using the Jacobian sensitivity matrices for signal propagation prediction. INTRODUCTION The focus area of this paper is mine safety, related to hazardous atmospheric conditions in a mine ventilation system. Improvements by recognizing safety hazards caused by heat of combustible gases or the accumulation of poisonous gases in a mine are addressed. The recognition of safety hazard by manual evaluation is difficult because of the complex nature of information and the large amount of monitored data from measurement by atmospheric sensors such as air velocity, pressure, hazardous gas contaminants and temperature. In order to recognize problem-causing trends, it is necessary to evaluate continuously individual measurement data from the Atmospheric Monitoring System (AMS) of the mine during their time-dependent variations. In addition, the combined effects of various signal trends need to be simultaneously interpreted in their cross-effects. It is very difficult to foresee the possible outcomes of intertwined signatures of various problems by continuous human observation. For example, a steady, continuous methane concentration measurement together with a sharp drop in barometric pressure from the AMS sensors may be a case for worry in future time due to pressure-induced methane increase from the coal seam or the gob (Danko et al., 2013). This future increase can be predicted by a time-dependent Ventilation Air Model (VAM) and its surrogate Air Parameter Predictor Solver (APPS) model. A calibrated VAM or APPS model can indeed predict a likely methane concentration variation in future time as a function of previous and new air pressure as well as air velocity (Danko, et. al., 2013). Such a future trend, however, cannot be seen from the raw measurement data."

Jan 1, 2017

By D. Carr, C. Anderson, M. Deal, C. Larson

"Construction of the OceanaGold Haile operation’s process plant in Kershaw, South Carolina is currently under way, with ore through the mill expected in late 2016 and commercial production expected in early 2017. The process is designed to treat 6,350 tonnes per day with minor upgrades required to achieve 8,270 tonnes per day. Plant optimization during detailed engineering, combined with a focus on de-risking the process, has resulted in numerous process changes since the initial design. This paper describes the plant optimization and de-risking, it also presents a proven commissioning strategy modelled after OceanaGold’s Didipio operation, whilst identifying potential expansion opportunities. INTRODUCTION Haile Gold Mine is located in Kershaw, South Carolina, approximately 50 miles south of Charlotte, North Carolina. Gold was first discovered at the site in 1827, and the property has been through several operating periods since. The last operation employed heap leaching from 1985 through 1992. Since then, the property has been closed and fully reclaimed. Romarco Minerals acquired the property in 2007, and began an exploration program that delineated 2.02Moz. of gold in reserve at an overall grade of 2.06 g/t. OceanaGold acquired Romarco Minerals and the Haile Operation in October of 2015. OceanaGold operates under a risk management philosophy in all aspects of operation, both corporately and at each individual business unit, and has implemented numerous process changes to eliminate or mitigate risks identified in the initial design of the processing circuit, and provided increased opportunity for optimization and expansion. This paper describes the plant optimization and de-risking, it also presents a proven commissioning strategy modelled after OceanaGold’s Didipio Operation, and identifies potential expansion opportunities. INITIAL PROCESSING CIRCUIT DESIGN An extensive metallurgical test work program was undertaken by Romarco Minerals and third party laboratories during the initial design phase of the Haile project [1]. This preliminary test work provided the technical information as a basis of plant design. The initial flow sheet for the Haile processing circuit is shown in Figure 1 (see APPENDIX). The plant is designed to process 6,350 tpd (7,000 stpd) on an annualized basis. The process begins with a jaw crusher followed by a SAG and ball mill grinding circuit to reduce particle size to P80 74 µm. A flash flotation cell treats 50% of the cyclone underflow in the ball mill circuit. Grinding circuit product is sent to a rougher flotation circuit to recover gold-bearing pyrite. The flotation concentrates from flash and rougher flotation are reground to P80 13 µm using stirred media detritors (SMD’s). The rougher flotation tail is pumped to the carbon-in-leach (CIL) circuit for gold recovery. The reground concentrate is pre-aerated prior to being pumped to the CIL circuit. The CIL circuit is a hybrid circuit with eight tanks. Tank 1 leaches the pre-aerated concentrate only, and tanks 2 through 8 leach the combined flotation tailing and tank 1 discharge. The carbon strip circuit is a standard pressure Zadra system, followed by electrowinning, and refining using an induction furnace. CIL tailing passes through a cyanide recovery thickener prior cyanide destruction and then pumped to the tailing storage facility (TSF)."

Jan 1, 2017

By Reda M. Bakeer

"An approach slab is the roadway segment that immediately follows a bridge intended to provide a smooth transition between the two elements. Some approach slabs have developed rough rideability with time due to differential settlement between the roadway embankment and the bridge. Soils in south Louisiana are generally poor and highly compressible and, therefore, pile-supported approach slabs were occasionally used. Timber piles of variable lengths are driven into the soft soils where no appreciable toe support exists. This resulted in the soils both supporting loads through shaft resistance and yet experiencing long-term consolidation settlement. Field testing and review of the records of over 120 approach slabs constructed in south Louisiana yielded the conclusion that their performance is primarily governed by negative skin friction (downdrag) imposed on the relatively short timber piles. A software (TU-DRAG) was developed to evaluate the deflection profile of a pile-supported approach slab based on its geometry and conditions of the underlying soils. It evaluates the effect of dragload considering the number and spacing of the piles at each transverse row and their variable lengths along the approach slab. TU-DRAG was utilized in the design of two transportation related projects which have been in service for more than 10 years.INTRODUCTIONThe problem of differential settlement at bridge approaches or “the bump at the bridge” has been recognized for many years. Research studies (1986, 1989, 1997, 2009 and 2013) by the Transportation Research Board (TRB) and the Federal Highway Administration (FHWA) provided comprehensive evaluations of the performance of bridge approach slabs by assessing their field conditions and construction and maintenance records. Various states have also performed their own studies to investigate the performance of bridge approach slabs. The studies considered various types of structures including soil- and pile-supported approach slabs, integral bridge abutments and open-end abutments. Recommendations were provided for the design of new structures and for maintaining and repairing existing structures. Guidelines were offered regarding tolerable movements of bridges and their foundations based on measurements of vertical and horizontal movements of 580 bridges Moulton (1986). Vertical and horizontal movements greater than 102 mm (4 inches) and 51 mm (2 inches), respectively, were considered intolerable. Tolerable limits for angular distortion (differential settlement to span length) were suggested to be 1/250 and 1/200 for continuous and simple spans, respectively. It was reported that a differential settlement greater than 13 mm (0.5 inch) at the bridge interface would be sufficient to constitute a “bump” requiring mitigation."

Jan 1, 2017

By Takafumi Kasaya, Katz Suzuki, Yoshifumi Kawada

"INTRODUCTIONThe area beneath the seafloor preserves valuable resources that are inevitable to sustain our industrial society. Hydrocarbon resources such as petroleum and natural gases are one of the representative examples, which have been mined over a century (Brandt et al. 1998). In addition, submarine resources such as methane hydrates, ferromanganese crusts, and metal deposits of hydrothermal origin have long been known (Rona 2003; Kvenvolden and Rogers 2005), although methods of their mining have not yet been developed. All of these resources are distributed heterogeneously, and various exploration techniques have been developed and examined. The Japan Agency for Marine-Earth Science and Technology (JAMSTEC) is conducting a project on the development of exploration methods of these unexploited resources (Urabe et al. 2015; also see http://www.jamstec.go.jp/sip/images/pamphlet_e.pdf). The present study particularly focuses on our attempt on the developing an exploration method of hydrothermal ore deposits.Seafloor hydrothermal ore deposits are associated with submarine volcanoes of mid-ocean ridges, hot spots, and island arcs, and back arcs (Hannington et al. 2010). Active hydrothermal systems discharging high-temperature fluids can be detected above the seafloor as anomalies of temperature, turbidity, and acoustic impedance (e.g. Kasaya et al. 2015). However, because of the temperature limitation of mining (Boschen et al. 2013), the target of mining may be extinct and probably buried. To explore buried hydrothermal ore deposits from the vast seafloor area, geophysical surveys that can obtain information below the seafloor must be required. Several techniques including magnetic, electrical, and gravitational methods have been developed (e.g. Jones 1999; Kowalczyk 2008). Although physical properties taken by these methods are sensitive to the presence of hydrothermal deposits, difficulties are sometimes encountered. For example, anomalies of magnetic susceptibility and electrical conductivity, which characterize the presence of ore deposits, may be found above non-hydrothermal bodies such as volcanic bodies and reservoirs of hydrothermal fluids (e.g. Honsho et al. 2016). Thus, combinations of multiple methods must be used to specify the existence of buried hydrothermal ore deposits"

Jan 1, 2017

By J. Herhold, S. Plaum

"Current and future operational processes in the mining and underground construction sector are under the influence of the prevalent competition and the acute necessity of optimization approaches concerning corporate and project processes. Besides general construction procedures, especially underground construction procedures and procedures in the field of deep shaft construction are high-profile. Those processes describe high technical challenges as well as increased requirements to occupational safety and health. Therefor an occupational safety management, which should be adjustable to the company itself and adaptable to all kinds of projects, shall be created. The creation of such an occupational safety management would lead to an economically optimized and safe (within the scope of OSH law) implementation of internal activities for the performance of construction services underground and in the field of deep shaft construction. With this approach the satisfaction of the high safety request as well as the demand for process optimization, as part of keeping the own competitiveness, will be satisfied successfully at once. PROJECT BACKGROUND Introduction The health and safety protection as well as occupational safety look back on a long historical development, which had brought more important sectors and developments during the last years, not only in Germany but also on the European and international level. The accident insurance protected by law has already been reported in 1884, which is astonishing early. The launch time point is strongly connected with the on-going economic development in the end of the 18th century, but above all this increased in the 19th century. The progress of occupational safety and especially the interest in the integration and the concentrated consideration of occupational safety and the health and safety protection in the company process is strongly visible during the 19th century and directly connected to the industrial revolution. [9] The industrial revolution and with that the development of work places lead to changing demands in the field occupational safety and health and safety protection. Insufficient security precautions caused problems in the industrial revolution, such as personnel and material losses as well as serious injuries and their consequences. These and the fundamental economic endeavours of the entrepreneurs lead therefore to the important step to develop an occupational safety system. [9] The prevailing basic ideas seize the insufficient security precaution of work places as well as the economical and profitable ideas of the entrepreneurs and bring them together. From this the necessary entrepreneur’s task comes into being and that is bringing the work conditions to the way that life and health of employees are not in danger. [9]"

Jan 1, 2017

By P. F. Ledwaba

"Artisanal and small-scale mining (ASM) in South Africa received official recognition after the change in government in 1994.The Reconstruction and Development Programme (RDP) recognized the sector as a vehicle for social and economic development for historically disadvantaged South Africans (HDSAs) who had previously been excluded from participating in the mainstream economy. Having recognized the ASM sector, government introduced several interventions and support structures to foster the development of ASM, to encourage participation of HDSAs, and to address challenges facing the sector. The objective of this paper is to assess the progress made, with particular regard to challenges in the sector. The paper focuses on the policy requirements that were deemed important for the growth of the ASM sector by the White Paper on Minerals and Mining Policy (1998). These can be collated into five categories: access to mineral rights, access to finance, access to markets, technology and skills, and institutional support. The paper provides a review of the support interventions, their intended roles and impact on the sector, and identifies existing gaps and possible ways of dealing with the challenges. There is a need for research to assess the real impact of these past and existing interventions on the ASM sector to draw lessons for future development.IntroductionThe significant rise in artisanal and smallscale mining (ASM) activities worldwide has led to many countries recognizing the sector. ASM takes place in approximately 80 countries (World Bank, 2013). It is estimated that the sector employs between 20 and 30 million people around the world (Buxton, 2013). This compares to between 3 and 3.7 million in 1999 (International Labour Organization, 1999). ASM activities are widespread, occurring mostly in developing countries in Africa, Asia, Oceania, and Central and South America (World Bank, 2013). There has been a significant increase in the number of people participating both directly and indirectly in the sector and this is expected to continue given the socio-economic realities of most developing countries. High levels of poverty and unemployment and growing inequality continue to be largest problems facing the majority of developing countries today. The ASM sector plays an important role as a source of livelihoods, particularly for those residing in rural areas with limited economic opportunities. In the majority of countries, the recognition of the ASM sector was driven by its increasing contribution to socio-economic development through job creation, poverty alleviation, and rural development. In response, a number of intervention strategies were introduced in support of the sector to address its negative impacts and to increase its potential benefits."

Jan 1, 2017

By Brandon T. Buschmeier, Sonia S. Swift, Michael P. Walker, Frederic Masse

"Ground improvement has undoubtedly become a cost-efficient and effective solution to support the development of poor soil sites. Ground improvement elements, such as Controlled Modulus Columns (CMCs), replace piles by improving the subsurface soils and reducing settlement. As ground improvement becomes more popular, the applications become more creative and ground improvement is being used to control settlements under large structures with tight settlement tolerances.In this paper, we will discuss the use of CMCs to support two (2) large industrial warehouses where soil conditions would normally lead to the use of deep foundations and a structural slab, grade beams, and hung utilities to prevent excess settlement. Each of the sites we will discuss had poor soil conditions in the form of very soft or compressible soil, heterogeneous fill of varying thickness, and environmental contamination. At each site, we developed a design that would allow for the use of Controlled Modulus Columns (CMCs) with a Load Transfer Platform (LTP) in place of the previously-proposed deep foundations. The use of the CMCs also allowed for the use of spread footings and slab on grade construction. The benefits of this value-engineering approach include economy in the foundation system, risk mitigation by not disturbing contaminated soils requiring expensive removal, and ease of access for future sub-slab upgrades with new tenants. Additionally, the use of recycled concrete aggregate as an LTP is more environmentally friendly than placing structural slabs with heavy steel reinforcement.Designing for the settlement of large warehouses is challenging because it requires changing how we typically perform our designs. For most structures, the slab loads are relatively light when compared to the footing loads, whereas for warehouses, the slab is heavily loaded compared to the relatively light footing loads. Thus, it becomes essential to perform three-dimensional analyses to confirm that the proposed CMC layout will provide uniform support of the slab and footing across a variety of loading scenarios (loaded bays vs unloaded or travel bays). The complexity of the designs for these warehouses generated interest in conducting large area load tests over a grid of multiple columns. The performance of the area load tests provided invaluable information on the effectiveness of the LTP and CMC spacing. In this paper, we present a general description of CMC ground improvement, the differences between ground improvement and traditional pile foundations, our typical design methodology for CMC design, and the modifications to that methodology for warehouses."

Jan 1, 2017