Search Documents

By Z. Yang, X. Bian

"The synthesis of 3-hydroxy-2-naphthyl hydroxamic acid (H2O5) as a collector for bastnaesite is described. The flotation performance of H2O5 with respect to bastnaesite was investigated by flotation tests, measurements of the surface adsorption capacity, and polarizing microscopy. The results indicated that H2O5 exhibits superior collecting performance compared with direct flotation recovery of bastnaesite, with recoveries above 90% at pH 8–9. The adsorption mechanism of H2O5 on bastnaesite was studied by solution chemistry analysis and ?-potential tests. The results showed that the adsorption of H2O5 is associated with the types and concentrations of hydrolysis products of rare earth cations on the bastnaesite surface. At pH 8–9, the hydrolysis-dominant components RE(OH)2+ and RE(OH)2 + of the rare earth cations were adsorbed onto the bastnaesite surfaces, which were considered to be the major positive active points and were beneficial to chemical adsorption of the reagents. The pH range of 7–10 was optimum for bastnaesite floatability, and the adsorption of H205 on bastnaesite was by means of chemical adsorption through formation of a five-membered ring chelate. IntroductionThe rare earth elements (REEs) have long been known as ‘industrial gold’ and are widely used in the petroleum, chemical, ceramic, metallurgical, and permanent magnet material industries because of their special physicochemical properties (Chen, 2011; Krishnamurthy and Guptac, 2002; Esquivel, Bohe, and Pasquevich, 2002; Abrahami, Xiao, and Yang, 2015). Demand for REEs is growing in response to continuous advances in science and technology. Currently, most REEs are extracted from bastnaesite ((Ce,La)CO3F) (Chelgani et al., 2015; Yosry, 1990), which is recovered from rare earth ores by flotation. Typically, hydroxamic acids are used as bastnaesite collectors (Xu, 2015; Ren, 1997; Mousumi and Venugopal, 2016). Research into the mechanism of interaction between hydroxamic acids and bastnaesite is important for improving the recoveries of bastnaesite. However, there have been few studies that examine this mechanism."

Jan 1, 2017

By Afshin Sadri, Wai Lai Ying, Brycklin Wilson, Zoe Coull

"Although there have been great steps forward to integrate corrosion engineering into operations, there is still an underlying tendency for maintenance tasks to be performed in a reactive manner. This is especially true when strategies focus on lagging indicators such as visual inspections, RCA (root-cause analysis), and FMECA (failure mode, effects and criticality analysis). This trend to “reactive maintenance” can be avoided by utilizing more inspection and monitoring methods to identify leading indicators of failures. Prevention is generally less costly than repairs; moreover, when paired with appropriate monitoring techniques, intervention of corrosion protection can be more effectively timed and based on more accurate data. Hatch asset reliability studies show nearly 80% of defects are introduced through operations and maintenance. Therefore, proactive corrosion management can provide the necessary feedback to optimize operations and maintenance strategies preventing costly corrosion losses. Understanding corrosion risks gives a clear picture of the benefits of a proactive approach to asset performance. Monitoring techniques (Non-Destructive Testing, field testing, sampling, etc.) by nature are a more effective means of improving maintenance efforts and preventing corrosion losses than other methods (RCA, FMECA). This paper will outline the importance of proactive corrosion management and demonstrate its benefits through industry examples.INTRODUCTION Over the past few decades, with the growth of technology and awareness of sustainable development many studies have shown the benefits of a proactive approach to maintenance strategies. However, in practice there is still an underlying tendency for maintenance tasks to be performed in a “reactive manner”. This is especially true when strategies focus on lagging indicators such as visual inspections, RCA (root-cause analysis), and FMECA (failure mode, effects and criticality analysis). This trend to “reactive maintenance” can be avoided by utilizing more inspection and monitoring methods to identify defects and leading indicators to failures."

Jan 1, 2017

By Elizabeth McIsaac, Wylie Spicer

"In July 2016 the International Seabed Authority (the “ISA”) released a first working draft of its mineral exploitation regulations as well as the standard contract terms for mineral resources in the Area, for which stakeholder input was sought in late 2016. In January of 2017 the ISA released a discussion paper on environmental matters related to these draft regulations. The ISA is now in the process of further developing its draft exploitation regulations and standard contract terms to ensure that seabed mining is carried out in an environmentally sound way for the common benefit of mankind.As the regulator of the “Area”, the ISA can draw lessons from onshore mining regulators and offshore petroleum regulators for their experiences in legislative drafting to smoothly and safely oversee project development, implementation, and closure. However, one of the unique challenges that the ISA faces in regulating private industry is its status as an international organization and not a sovereign nation, which results in a significantly different legal relationship between the regulator and the regulated. The result is that the exploitation contract is the sole legal connection between the mining proponent and the regulator for the exploitation phrase of the project.Accordingly, in the regulatory development process, the ISA must carefully consider which rights and obligations are set out in the exploitation contract versus the regulations. This decision will dictate the flexibility the ISA will have to modernize the conduct required of mining proponents in response to changing best practices in the industry, technological progress, and advances in the understanding of the marine ecosystem. As the first working draft of the exploitation regulations sets out an initial contract period of twenty years, it is crucial for the ISA to carefully consider the rights, obligations, and procedures it agrees to in the exploitation contract, as unilateral amendment will not be possible after contract execution."

Jan 1, 2017

By S. McPherson, M. Chalkley, R. Ellenwood, W. Nicot

"The Moa JV was formed in December 1994 as a 50/50 joint venture between Sherritt Inc. and General Nickel Company S.A. of Cuba. The joint venture consists of the mine and Pedro Sotto Alba processing plant in Moa, Cuba and the Corefco refinery in Fort Saskatchewan, Alberta, Canada. Throughout its now nearly 23-year history, the Moa Joint Venture has faced a number of global, operational and process challenges. Global challenges have included high input costs such as for fuel oil and sulphur, as well as low nickel prices. Operational and process challenges have included increasing ore haulage distances, decreasing ore Ni + Co grades, and increasing ore impurity contents. For example, increases in impurities such as Mg and SiO2 in the ore result in increasing acid demand in leaching and decreasing solids content of preheated leach feed slurry, respectively. In spite of these challenges, the mixed sulphide production capacity from the Moa Joint Venture has increased from 12,500 to 37,000 t/y Ni + Co since 1994 by judiciously targeting expansion projects and by continuously performing process and operational improvements.INTRODUCTION The Pedro Sotto Alba high pressure acid leach (HPAL) plant at Moa Bay, Cuba has a long history (Maslenitzkiy, 1969; Chalkley, 1996; Carlson, 1960; Roy, 1961; Carlson 1961). The plant was constructed by Moa Bay Mining Company and started up in late 1959 after several years of process development by Freeport Nickel Company, including operation of a 10 t/d plant in Hoskins Mound, Texas and a 50 t/d plant in Port Nickel, Louisiana (Southwick, 2004), as well as development work by Chemical Construction Company (Chemico) to precipitate metal sulphides (Roy, 1955a; Roy, 1955b). The Moa plant had an original reserve of 50,000,000 t of ore, graded at 1.35 wt% Ni, 0.146 wt% Co, 3.70 wt% Si, 1.00 wt% Mg and 4.5 wt% Al. At original design rates of 2,000 kt/y of ore, the design capacity of the plant was around 25,000 t/y Ni + Co as a mixed sulphide product, which would be shipped to the Port Nickel Refinery in Louisiana for processing. In 1960, the plant changed ownership and was restarted in 1961 under Cuban management. Between 1961 and 1989, the plant was also supported by involvement from the former USSR, supplying spare parts and consumables. In 1994, Sherritt Inc. partnered with the General Nickel Co. S.A. of Cuba and formed the Moa Joint Venture. This joint venture includes the mine and Pedro Sotto Alba HPAL processing plant in Cuba and the Corefco refinery in Fort Saskatchewan, Alberta, Canada. Under this partnership, ore is processed in Cuba to produce a nominally 55 wt% Ni and 5 wt% Co mixed sulphide product that is shipped to Canada and processed by Corefco to produce class 1 nickel, high grade cobalt and byproduct ammonium sulphate fertilizer."

Jan 1, 2017

By C. Feng, D. W. M. Arrigan

Arsenic is often associated with gold mining operations and poses a significant health and environmental hazard. While a number of technologies are available for removing arsenic, none of them is effective under all conditions. Although adsorption is a promising approach, most methods focus on the purification of water under neutral or acidic conditions and tend to be less effective in gold mining process waters, operating under alkaline conditions. In this study, the removal of As (III) and As (V) from both arsenic-only solutions and simulated process waters using composite magnetic nanoparticles was investigated. The nanoparticles consisted of magnetite (Fe3O4) or maghemite (?-Fe2O3) cores covered by various metal oxides with Langmuir adsorption capacities of As (III) and As (V) ranging from 31.4 to 79.1 mg/g and 10.2 to 25.5 mg/g, respectively, in arsenic-only solutions at pH 9. Their adsorption capacities were further recognised by the adsorption tests conducted in simulated process waters. The ability to remove As (III) is of particular importance as it is harder to remove it from alkaline solutions. The magnetic cores allow simple and efficient magnetic recovery of the As-loaded nanoparticles.

Jan 1, 2017

By A. G. Doll

"Many power-based grinding models exist, and most operators are familiar with Fred Bond's ""third theory"". Bond's model is most commonly used to describe primary and secondary grinding to product sizes above, for example, 100 µm. Operators sometimes use Bond's equation to describe grinding in situations where it is not appropriate, such as fine grinding below 50 µm. Using an alternative model would be a better choice in this situation.Bond's equation is one in a large family of models. Related equations better suited to fine grinding include the “signature plot”, Von Rittinger's model and Charles' equation. These models have a similar form to Bond's and can be fit to industrial regrind mills and laboratory tests using the simple regression tools in the charts of computer spreadsheets. Operators will find that fine grinding calculations are both easier and more accurate when using the alternative equations to fit their regrind milling surveys or when performing laboratory regrind mill scale-up for plant design.None of these models are new: Charles' equation was published in 1957 and Von Rittinger's model was proposed in 1867. A quick refresh how to apply these equations can turn these oddities from the undergraduate curriculum into useful tools for plant optimization. They can be fit to any type of mill including stirred and tumbling ball mills.IntroductionBuilding a case for fine grind modelling requires reviewing some theory before building a framework for doing fine grinding calculations. The actual calculation procedure recommended is easy and can be applied by plant metallurgists. Don’t be frightened by the theory; the end result is reasonably simple.The observation that mineral breakage is related to the absorption of energy is usually attributed to Von Rittinger (1867). Lynch and Rowland (2005) describe that the ability to empirical test and calibrate energy models of breakage didn’t exist until the widespread adoption of electric motors in the mining industry during the 1930’s and 1949’s. A series of technical papers published by the Allis Chalmers company during the 1940’s demonstrate that they were attempting to do such a calibration using Von Rittinger’s model which is usually stated as: “the energy consumed in the size reduction is proportional to the area of new surface produced.”"

Jan 1, 2017

By Jorge Olivari Ortega

"El presente texto describe la leyenda de los tesoros de plata de Catalina Huanca, perteneciente al valle de Huancayo. El origen de esta estriba en dos versiones. La primera, indica que es ahijada del conquistador español Francisco Pizarro, quien por razones políticas, decidió apadrinar a la menor y la segunda, que era un alias de Teresa Apoalaya, la hija del curaca Carlos Apoalaya (descendiente de Machu Apo Alaya). Ella habría nacido en Chupaca en 1678 y asumiría el curacazgo en 1698. Catalina Huanca murió casi a los noventa años de edad, durante el gobierno del virrey Diego Fernández de Córdova (1621-1628) y fue enterrrada con grandes cantidades de plata. "

Jan 1, 2017

By N. Schmalbein, L. von Ketelhodt, L. Kotelo

"The mining industry continues to remain challenged. Lower commodity prices, increasing labor costs and more importantly diminishing reserves are amongst some of the primary factors contributing to the difficulties faced. Ore sorting technologies have demonstrated their potential to improve the downstream beneficiation performance. The general processing route sees all primary crushed material milled for liberation and then processed in accordance with characteristics of the gold therein, i.e.: refractory golds would require direct leaching or oxidation whilst free gold would follow the conventional cyanidation process, after gravity concentration. Ore dilution increases the associated operating costs within each stage of this process. The opportunity to process the same throughput at a higher grade can only be achieved through pre-concentration. Sensor based sorting has been examined on numerous occasions by various gold producers. Test work carried out on different bulk low grade gold ores has shown the successful applicability of ore sorting to remove waste, whilst maintaining high recovery rates of gold. The results of a combined XRT/Laser sensor sorter have shown grade improvements of over 300% from feed grades of 0,25g/t to 1,15g/t at gold recoveries of 66% and waste ejection rates of 85%. This paper presents some of the results from the work undertaken by STEINERT with respect to gold sulphide ore sorting and presents a modelled financial scenario, which can enable a company to target and reclaim low grade ores.INTRODUCTION The mining and minerals processing industry presents with many different challenges including, volatile commodity prices, increasing labor costs and more importantly diminishing reserves. Conventional processing routes will continue to play a crucial role in the beneficiation process, however innovative methods of reducing operating costs and optimizing on the overall circuit performance is where technologies such as sensor based sorting come into the fore. Sensor based sorting as a dry mechanical process not only reduces water consumption by eliminating unnecessary waste but also reduces the requirements for reagents in the downstream processes. Sensor based sorting under dry conditions presents a highly efficient alternative to wet pre-concentration methods such as dense medium separation (DMS)."

Jan 1, 2017

By Shuvranshu K. Rout, Anup K. Mandal, Biswajit Das, Manos De

"To adopt new technology advancement in Steel Plant, there is a requirement of shifting of operation process from Coke Wet Quenching (CWQ) to Coke Dry Quenching (CDQ). New CDQ chamber foundation with deep basement and underground conveyor tunnel are to be constructed in an operating plant where heavy foundations and structures are located in close proximity. Furthermore, the existing CWQ system will be in operation during new underground construction and erection. Challenges to deep excavation of tunnel and chamber foundation consist of non-uniform ground condition, prevent washing out of soil from bottom of existing foundations, stability of existing nearby structures, presence of large number of underground utilities, ensuring safe underground workplace to construction resources engaged in new construction work along with project schedule and budget constraints. A combination methods involving use of soil nailing, soil grouting, contiguous bored pile and micro pile had been adopted for protection of excavation sides as well as existing structures. Each side of excavation in different stretches were analysed during design as well as construction stages. The use of combination of all techniques in a single brown field project in context of the nature of site constraints and safety issues made this a unique project.INTRODUCTIONSteel Industry is one of the backbones of industrial growth of any developing country like India. Due to increasing land prices most of the steel plants in India are expanding within their existing plant facilities. In addition to that, there is demand of adoption of new technology for future expansion projects to set new benchmarks with global standards.The property owner had earlier installed a Coke Wet Quenching (CWQ) for their Coke Plant. Now, there is a requirement from process department to proceed with Coke Dry Quenching (CDQ). To facilitate the CDQ within the existing CWQ which will be in operation is the main challenge for the property owner. The second challenge is the limited space for underground construction and subsequent equipment erection within the stipulated time frame.From a geotechnical prospective, the project team had uncertainty and reservations in their mind about the construction methodology. Therefore, the role of three “C”: ‘Consultant’-‘Client’- ‘Contractor’ and their combining brainstorming is essential to freeze a working plan for achieving the goal. In this paper, only the excavation support systems for underground foundation structures have been highlighted in the context of solving geotechnical problems."

Jan 1, 2017

By T. G. Maepa

"The creation of mine excavations alters the stress distribution in the surrounding rock mass. In modern mining, resin-grouted rockbolts are used as a means of support in order to redistribute stresses and reestablish equilibrium in the rock mass. The success of resin-grouted rockbolting depends on the design of the system and the correct installation of the support units.The support design and rockbolt installation procedure at a platinum mine in the Bushveld Complex were investigated. A number of issues that resulted in poor installation were identified, including resin admixture, incorrect length and orientation of support holes, over- or under-spinning of the resin, and incorrect rockbolt tensioning. The support design used at the mine was reviewed and its limitations identified. A number of recommendations were made for optimizing the support design by reducing the diameter of the drill bit and reducing the length of the support holes. These changes will enable the mine to use different combinations of resin capsules. Implementation of the proposed changes will lead to a significant reduction in the cost of installation per support hole, as well as improve productivity and safety.IntroductionThe creation of any mine excavation disturbs the virgin state of stress in the Earth’s crust. This results in stress concentrations that interfere with the stability of the rock mass surrounding the excavation. It is essential to modify the internal behaviour of the rock mass surrounding excavations in order to reinforce the ground and stabilize excavations. Resin-grouted rockbolts are extensively used for this purpose. Esterhuizen (2014) stated that when effectively installed, the rockbolt exerts a clamping force and a bonding strength that keeps the rock mass together. This increases the cohesive strength of all discontinuities in the rock mass and enhances the stability of the excavation. Poorly designed and installed ground support is ineffective and constitutes a safety hazard. It is therefore crucial for every mine to ensure that any form of ground support is designed and installed correctly. This research evaluates the installation of resign-grouted rockbolts and identifies challenges and solutions for improved safety as observed at an operating hard rock mine. The support design used at the mine was reviewed and the design parameters optimized. The outcomes will enhance the efficiency of support and minimize the costs associated with the installation of resingrouted rockbolts."

Jan 1, 2017

By M. B. Kime

"Discrete-element method (DEM) modelling is a powerful tool for studying particulate systems within the mineral processing industry. DEM simulations were conducted to investigate the power draw, load behaviour, and impact energy profile of an experimental ball mill under different milling conditions. The variables considered were mill rotational speed (percent critical speed), ball size, and lifter face angle. The simulation results indicated that the grinding efficiency would be enhanced by using 80% critical speed, 30 mm ball diameter, and 45° lifter face angle. These findings can be useful in guiding actual ball milling tests involving an ore sample.RÉSUMÉ La modélisation par méthode des éléments distincts (MED) est un outil puissant qui permet d’étudier les systèmes particulaires au sein de l’industrie de traitement des minerais. Des simulations par MED ont été menées de façon à étudier le profil de la consommation énergétique, du comportement de la charge et de l’énergie de rupture d’un broyeur à boulets expérimental dans diverses conditions de broyage. Parmi les variables prises en compte figuraient la vitesse de rotation du broyeur (vitesse critique en pourcentage), la taille des boulets et l’angle de coupe de la cornière élévatrice. D’après les résultats de la simulation, on pourrait améliorer l’efficacité de broyage en utilisant une vitesse critique de 80 %, un diamètre de boulet de 30 mm et un angle de coupe de 45 ° de la cornière élévatrice. Ces résultats peuvent se révéler utiles pour les essais concrets de broyage à boulets impliquant un échantillon de minerai."

Jan 1, 2017

By Swaminathan Srinivasan, Jess A. Schroeder

"Landslide activity along U.S. 50 in Cincinnati, Ohio (USA) has caused roadway damage for decades. After a necessary closure of three lanes due to slope movements, emergency stabilization measures were undertaken to protect the roadway by providing a short-term solution necessitated by The Ohio Department of Transportation budget constraints. The landslide shear plane occurred on a sloping bedrock surface as much as 50 feet below grade. Drilled shafts were installed 40 feet downslope of the roadway shoulder and were heavily reinforced across the shear plane but steel reinforcing did not extend the full length of the shafts and was stopped well short of the ground surface. Instrumentation data has been collected for 11 years after construction has shown these “Stub Piers” have provided much more than a short-term solution and have provided an attractive alternate to conventional deep shafts or tieback drilled shaft options.INTRODUCTIONLandslide activity has occurred along U.S. Route 50 in western Cincinnati, Ohio for many decades. The site is located between North Bend and Addyston, Ohio on the right descending (cutting) bank of the Ohio River. Road distress caused by slope movements required periodic repairs over recent decades. Railroad tracks downslope of the roadway also showed signs of horizontal displacement and periodic repair. Visual evidence in 2005 suggested the shear plane extended below the US 50 roadway and extended out into the Ohio River.A weed and brush-covered slope extended down slope from the roadway at about 3H:1V for a vertical distance of about 20 feet. Above US 50, the hillside continued to rise more than 100 feet. There is a railroad right-of-way at the toe of the slope with the Ohio River bank just downslope of the railroad.In 2005, Terracon Consultants was retained by the Ohio Department of Transportation (ODOT) to perform a geotechnical study that included 17 test borings and inclinometer monitoring at 4 locations. Roadway damage was occurring (see Figure 1). After only a few weeks of monitoring, the inclinometer casings sheared off about 50 feet below grade, near the soil / bedrock interface (see Figure 2). Soon after, the roadway distress worsened, causing ODOT to close 3 of the 4 lanes to traffic and reroute traffic onto the remaining single lane and shoulder. Terracon was asked to develop a stabilization design under emergency repair conditions. However, both limited budget and time-related constraints necessitated a direction by ODOT that the solution be at least “pseudo” short-term (3 to 5 years)."

Jan 1, 2017

By Jeremy Spearman, Alan Cooper, Mark Lee, Jon Taylor, Michael Turnbull, Neil Crossouard, Bramley Murton

"SUMMARYSeamounts are underwater mountains caused by volcanic activity. They are of great oceanographic interest because of their local and basin-scale influence over ocean systems, their often unique ecosystems, and because they are associated with the formation of ferromanganese (Fe-Mn) crusts. These crusts are of particular interest to scientists because they are rich in some of the rare elements increasingly required for development of renewable technologies. When the possibility of mining such seamounts is considered, an inter-disciplinary study of seamount hydrodynamics, crust formation and ecosystem sensitivity is required. MarineE-tech is one such multi-disciplined project that has been commissioned to address these different aspects in order to improve understanding of the viability and desirability of mining Fe-Mn crusts. This paper describes a key part of this study, namely the development of a model, informed by hydrographic observations, of the currents around one such seamount and the in situ validation of a sediment disturbance plume model as a pre-cursor to assessment of the potential effects of mining activity.INTRODUCTIONFerromanganese crusts are thought to form by precipitation of iron and manganese oxides from oxygen depleted mid-water known as the oxygen minimum zone (OMZ). Oxidation rich waters, typically at depths of about 800-2200 m (Hein et al, 2000). This range of depths coincides with the flanks and summits of many seamounts. The ferromanganese crusts found on seamounts have been found to have high concentrations of rare elements, like Tellurium, that are considered critical to low-carbon energy production. Seamounts are complex environments: in terms of the local hydrodynamics that tend to trap water over the seamount due to the Taylor Cap effect (e.g. Chapman and Haidvogel, 1992) and which can enhance the productivity of seamount waters through upwelling (Lavelle and Mohn, 2010), in terms of the microbiological activity that leads to the precipitation of the Fe-Mn crusts, and also in terms of the often unique ecosystems that are the product of the “island” nature of seamounts and the upwelling of nutrients. The understanding of this complexity is a necessary journey towards the realization of viable, yet environmentally responsible, mining schemes. The formation of crusts will be influenced by the local (and larger-scale) hydrodynamics. The exploration of promising crust sites could be made much more efficient by understanding where the most prospective deposits are likely to occur. Knowing how to remove these crusts without impacting significantly on the local environment will be a pre-requisite for such mining to be acceptable to the public and funders alike."

Jan 1, 2017

By A. Acar, E. T. Tuzcu, Y. O. Vural

"In order to sustain the operations in chromite processing plants, due to concentrate selling cost, plants are in need of optimization in terms of capacity and recovery increase. In this study, DAMA Engineering carried out a methodological study for the purpose after a detailed sampling campaign in a plant which is situated in one the main chromite zones in Turkey; 1 The current status of the plant was investigated quantitatively with the bottlenecks, Plant overall efficiency in terms of recovery, Efficiencies of the particular equipment (mill, screen, gravity circuit), 2 A new circuit was proposed with the available equipment, 3 The new circuit that is product of modeling and experimental effort, was evaluated quantitatively as if it is a running plant, After 4-5 months continuous effort, the capacity of the plant was almost doubled (37 tph to 70 tph) and the plant overall recovery was increased from 48% to 63% by grinding adjustments and additional shaking tables theoretically. It was shown that the plant may move into profit with the minimum amount investment using readily available system. INTRODUCTION TO THE CURRENT PLANT The objective of the study is to increase the capacity and recovery of the chromite plant owned by Kurmel Group, Akmetal Inc. The complete study is given elsewhere (DAMA, 2016). The plant is situated in one of the main chromite zones in Turkey; Aladag. The current capacity of the plant is around 35 tph and the overall recovery declared by plant engineer is around 47 %. The chromite plant mainly has 3 units; crushing, grinding and gravitational circuits. The crushing circuit has 3 stages; a jaw crusher, a secondary cone crusher and a tertiary cone crusher operating in closed circuit with a vibrating screen with the aperture size of 15mm. In grinding circuit, a rod mill (2.44 6m x 3.6) and a ball mill (2.13 x 2.3m) are used for primary and secondary grinding, respectively. Derrick screens are used for the size separation. Additionally, for the size classification of the system, hydrosizers are used and each size fraction is sent to the shaking table sets. The middling product of the tables is subjected to re-grinding with a ball mill with the dimensions of 2.1 x 2.9 m. The capacity and the recovery are affected by several bottle necks; hydrosizers’ pure classification, primary/secondary mill power vs capacity problems, re-grinding product’s high slime content and so on. These combined factors made the plant to run in low recovery and capacity. Hence, DAMA was asked to make a study to investigate current status of the plant and propose a new solution to increase capacity and recovery of the plant. The conceptual flowsheet of the circuit is given in Figure 1 below."

Jan 1, 2017

By Krishna Parameswaran

"This paper discusses energy use and conservation in the primary copper industry and illustrates eco-efficiency considerations, using select examples of practices at ASARCO LLC, an integrated primary copper producer and others in the industry that promote eco-efficiency. The World Council for Sustainable Business Development first publicized the concept of eco-efficiency at the Rio Earth Summit in 1992. Eco-efficiency is a management concept linking environmental and economic performance and is aimed at generating added value for a business through, among other things, increased resource and energy conservation and reduced environmental impacts throughout the life cycle of the product or service. This concept differs from sustainable development in that focus is only on economic and environmental factors and does not include social considerations. In the metal mining and processing context, this added value can be realized by implementing practices that promote conservation of water and mineral resources, conservation of energy, minimization of waste, reduced emissions and effluents and increased recycling. The examples from the primary copper industry used to illustrate eco-efficiency considerations include: water and energy conservation in mineral processing, adoption of flash and bath smelting processes, emission reduction and process improvement associated with fire-refining, implementation of green chemistry in electrorefining, promoting product stewardship initiatives and fostering renewable energy project on disturbed mined lands.INTRODUCTION ASARCO LLC (Asarco) was organized in 1899 as the American Smelting And Refining Company. Originally a consolidation of several lead-silver smelting companies, it evolved over the years into an integrated producer of primary non-ferrous metals, including copper, lead and zinc and associated co-products. Grupo México, S.A.B. de C.V acquired Asarco in 1999. Today, Asarco is a vertically integrated producer of primary refined copper and associated co-products such as gold, silver, molybdenum, selenium and tellurium. Asarco operates three open-pit mines and mills, two leach, solvent extraction-electrowinning (SX-EW) plants and a copper smelter in Arizona and a copper refinery in Texas."

Jan 1, 2017

By M. Kawata, T. Amano, T. Miyamoto, K. Shibayama

"The High Pressure Acid Leach (HPAL) plant of Taganito HPAL Nickel Corporation (THPAL), located in Taganito, Philippines, with a nameplate capacity of 30,000 Ni-t/year started commercial operation on October 2013. The plant load was smoothly ramped up and it achieved monthly production equivalent to 33,000 Ni-t/year in 2016. Partial improvement of the plant capacity for the achievement of 36,000 Ni-t/year, as evaluated from the current operation progress of each system is planned for 2017. In this paper, aside from presenting the progress of the plant ramp-up, research and development activities such as the reduction of nickel loss and the improvement of filtration capacity which was achieved by particle size control of ZnS precipitates in the Zinc Removal system are also discussed.INTRODUCTION Taganito HPAL Plant Project History of THPAL Taganito HPAL Nickel Corporation (THPAL) was incorporated in August 2008, as a joint venture of three (3) companies, namely Mitsui Corporation with 15% share, Nickel Asia Corporation (NAC) with 10% share and Sumitomo Metal Mining Corporation (SMM) with a controlling stake of 75%. Aside from its capital share, NAC’s Taganito Mining Corporation (TMC) supplies the ore for the HPAL plant located in Taganito, Claver, Mindanao, Philippines. The objective of THPAL is to produce 30,000 MT of nickel and 2,600 MT of cobalt as mixed (Ni/Co) sulfide by treating nickel laterite ore in the Philippines and exporting to Japan as raw material for SMM’s Niihama Nickel Refinery (NNR) for the next 30 years. In other words, 1.15 wt% of nickel in ore is refined to 99.99 wt% nickel in electrolytic nickel. The mixed (Ni/Co) sulfide is shipped to NNR and SMM provides the technology and management personnel to THPAL plant as well as sulfuric acid which is the main reagent for HPAL process. Figure 1 shows the location of THPAL and current relationship between the stake holders.The Characteristics of THPAL Plant In terms of plant design, a 2-train system is applied for the HPAL circuit considering the reliability of the process, facility and avoidance of whole plant shutdown due to HPAL troubles. The technical data, operation know-how and improvements gained from the successful operation of Coral Bay Nickel Corporation (CBNC) which was established in April 2002 were reflected in THPAL’s plant design. As for the H2S plant, a more economical design was considered which is different from CBNC."

Jan 1, 2017

By J. Witley

"Narrow tabular platinum group element deposits in the Bushveld Complex of South Africa are typically evaluated by diamond core drilling from surface. Several short deflections are drilled from each mother hole in order to obtain multiple intersections at a close spacing (less than 1 m). Examination of the intersections from deflection drilling revealed the importance of these deflections in understanding the representivity of the borehole, obtaining an estimate of the nugget effect, and mitigating the undesirable effect of the high grade variability at the ultra-short range that is a characteristic of these deposits. The use of deflections in estimation was investigated by means of a number of techniques and scenarios in order to find the most appropriate way to use them in an estimate. A significantly improved level of confidence was gained from using multiple close-spaced intersections rather than a single borehole intersection. IntroductionThe Upper Group 2 chromitite layer (UG2 or UG2 Reef) is known for its remarkable geological continuity, being traced almost uninterrupted for tens of kilometres. However, what is often less well emphasized is the high variability in platinum group element (PGE) grade and thickness (and therefore PGE content) and internal reef stratigraphy over very short distances (several metres or even tens of centimetres).This paper examines the application of short drill-hole deflections in evaluating UG2 PGE mineral resources at Marikana in the western Bushveld Complex of South Africa."

Jan 1, 2017

By M. B. Kime

"A set of experimental batch leaching tests studied the effect of pH, time, temperature, and stirring speed on the relative Cu, Co, Ni, and Fe leaching yields of an oxidized copper-cobalt ore sample in an aqueous hydrochloric acid solution. The results were statistically analyzed and modelled using the structural equation modelling method. Models showed that Cu, Co, and Ni leaching yields were strong functions of the leaching time and leaching temperature, whereas the Fe leaching yield depended on the leaching temperature, stirring speed, and pH. Under optimum leaching conditions yields were 99.8% Cu, 82.4% Co, 91.3% Ni, and 30.6% Fe.RÉSUMÉ Une série d’essais expérimentaux de lixiviation en bâchée ont été menés pour étudier l’effet du pH, de la durée d’attaque, de la température et de la vitesse de brassage sur les rendements relatifs de lixiviation du cuivre (Cu), du cobalt (Co), du nickel (Ni) et du fer (Fe) d’un échantillon de minerai de cuivre-cobalt oxydé dans une solution aqueuse d’acide chlorhydrique. Les résultats ont été analysés et modélisés statistiquement à l’aide de la méthode de modélisation par équation structurelle (SEM, de l’anglais structural equation modelling). Les modèles ont montré que les rendements de lixiviation du Cu, du Co et du Ni dépendaient énormément de la durée d’attaque et de la température de la lixiviation ; le rendement de lixiviation du Fe, quant à lui, dépendait de la température de la lixiviation, de la vitesse de brassage et du pH. Dans des conditions optimales de lixiviation, les rendements étaient de 99,8 % pour le Cu, de 82,4 % pour le Co, de 91,3 % pour le Ni et de 30,6 % pour le Fe."

Jan 1, 2017

By B. Soundara, A. Suganya, S. Selvakumar

"Expansive soils have a potential for shrinkage or swelling under changing moisture content. Attempts were made to reduce the swelling potential of expansive soils with conventional additives such as lime, cement, etc. and non-conventional additives such as industrial wastes. In this research an attempt is made to study the feasibility of using granulated waste expanded polystyrene (EPS) as an additive to expansive soil to control swelling. To investigate the effect of mixing waste EPS granules with expansive clays, three expansive soils with different plasticity index were manufactured in the laboratory by mixing sand with sodium bentonite of various proportions. A series of standard proctor test, California bearing ratio (CBR) test, one dimensional free swell and swell pressure tests were performed on these soils. Test results show that the inclusion of EPS granules significantly reduces the percent swell and swelling pressure when subjected to one-dimensional free swell conditions. The dry density and CBR values decrease with increase in EPS content and increased plasticity of the soil.INTRODUCTIONExpansive soils cover an area of about 257 Million hectares on the earth’s surface (Dudal et al. 1965). In India, the area covered by expansive soils is nearly 20 percent of the total area (Mohan et al. 1961). Movement is usually in an uneven pattern and of such a magnitude as to cause extensive damage to various structures, especially lightly loaded structures or pavements (Chen 1975). Stabilization is one of the methods of treating the expansive soils to make them fit for civil engineering purposes. The variety of stabilizers may be broadly divided into three groups (Petry et al. 2002): (a) traditional stabilizers (lime, cement etc.), (b) by-product stabilizers (fly ash, quarry dust, phosphor-gypsum, slag etc.) and (c) non-traditional stabilizers (sulfonated oils, potassium compounds, polymer, enzymes, ammonium chlorides etc.). Apart from these, a number of other ground improvement techniques such as sand cushion technique (Satyanarayana 1966); cohesive nonswelling (CNS) layer technique (Katti 1978) were adopted for the stabilization of expansive soils. Expanded polystyrene (EPS) is a polymeric foam normally available in white colour and is a wellknown packaging material. The geotechnical specialists recognize EPS as the most commonly used geofoam material, a type of cellular geosynthetic which has been in consistent use in geotechnical applications since the early 1960s (Horvath 1995). EPS has very low thermal conductivity and nearly 98% of the volume is air (Lye et al. 2002). EPS has many exceptional properties such as being lightweight, thermal insulating, shock-absorbing and having low-water pick-up, etc. EPS find its applications in geotechnical engineering as light weight fills in the form of blocks (Refsdal 1985, Karpurapu et al. 1992, Zou 2001, Ikizler et al. 2008). EPS can be used as compressible inclusion and as a vibration damper (Horvath, 1994&1995). EPS is also used in lightweight concrete owing to its lightweight, excellent heat preservation and sound insulation properties (Ravindrarajah et al. 1994; Miledet al. 2004 and Babu et al. 2005). Waste EPS granules have been used in with horticultural soils to improve a number of soil characteristics like improving drainage, lightening heavy soils and improving water uptake capacity of soils (Scheirs 1998). Furthermore, it was also used as sub-base materials for pavements and railway track beds (Hanna 1978; Duskov1996), construction materials for floating marine structures and fenders in offshore oil platforms (Bagon et al. 1976), sea beds and sea fences; as an energy absorbing material for buried military structures, (Perry et al. 1991)."

Jan 1, 2017

By Hayel M. El-Naggar, Marawan M. Shahien

"Large capacity piles are important type of foundation elements that are needed in case of high column loads such as in tall buildings with large span between columns. In many projects, especially if the designer uses the concept of one pile supporting one column (Hamza, 2003a & b). The axial capacity of the large bored deep foundations can be further increased by grouting the shaft skin and the base of the pile. The increase in the capacity of the piles due to grouting can be tremendous. Thus grouting appears as an ideal solution for achieving more reliable foundation and greater savings (Littlechild et al., 2000). A data base of pile load tests of instrumented grouted piles is under development in a major study aiming to propose a simple method to estimate the axial capacity of large bored grouted piles. The data base include pile load tests from projects constructed in Egypt and abroad. The main goal of this paper is to analyze pile load test(s) from one project. The tested deep foundations included 1.2 m diameter and 1.5 m diameter piles and a barrette of size 1.0mx2.8m. The instrumentation of the tested piles and barrette allowed for the separation of skin friction and base contributions to the axial load. Further, the contribution of the skin friction of every layer along the pile shaft could be identified. The results of the analysis clarified how base and shaft grouting increased the axial capacity of the pile and decreased the settlements for certain load level compared to conventional un-grouted piles installed under similar conditions.INTRODUCTIONIn recent years, significant research has been carried out to develop new techniques which are suitable to withstand problems in major projects such as high applied loads in high rise building, large spans structures projects and structures designed using the concept one pile supporting one column (Hamza, 2003a & b). Base and shaft grouting of piles are one of these new techniques which aim at decreasing the settlements and increasing the capacity of the pile under axial load that became major requirements in large projects (Stocker, 1983; Mullins et al., 2001; and Hamza, 2015).Base grouting consists of injection grout under pressure at the base of the pile after the concrete is sufficiently hard. Field evidences showed that the ultimate end bearing of base-grouted piles could be as high as 1.5 that of non-base-grouted bored piles (Suckling and Eager, 2001). Further, field evidences was provided by Shahien and El-Naggar (2015) that showed an increase in end bearing resistance due to base grouting reached to 2 to 3 times that of non-base-grouted bored pile. On the other hand, shaft-grouting causes increase in the soil density in the zone which had been disturbed by the pile construction and thereby improves the shaft resistance of the pile. Field measurements by Gouvenot and Gabaix (1975), Stocker (1983), Robson and Wahby (1994), Troughton and Stocker (1996), Byrne et al. (1998), Joer and Randolph (1998), Hamza and Leoni (1998), Littlechild et al. (2000), Hamza and Ibrahim (2002), Hamza (2003 a&b), Hamza (2015) and Shahien and El-Naggar (2015) showed that the shaft resistance of grouted piles could be nearly 1.5 to 5 times that of non-grouted piles."

Jan 1, 2017