Search Documents

By Edoardo Misano, Magali Schivre, Martino Semeraro, Alain Bochon

"INTRODUCTIONThe Laboratoire Souterrain de Modane (LSM) is an underground research laboratory located in the Western Alps on the French – Italian border. It is located in the middle of the 13km long Fréjus highway tunnel that links Modane (France) to Bardonecchia (Italy) in correspondence of the highest overburden of 1800m. The LSM current activity is mainly based on the investigations about the dark matter and requires very sensitive instrumentation which shall be protected from cosmic rays. To comply with the new legislation about safety in tunnels, the highway tunnels owners agreed in 2007 the construction of a parallel safety tunnel, at an average distance of 50m from the existing tunnel and the laboratory owner CNRS (Centre National de recherche scientifique) also decided to extend the existing laboratory with the construction of a new 17000 m3 cavern allowing the installation of wider and more powerful instruments that could increase chances of success of research. Preliminary studies stated that, considering both geological and functional issues, the most appropriate location for the new laboratory shall be in between the two tunnels and parallel to the existing laboratory (see Figure 1).Hence, the CNRS asked Systra, already in charge of the works supervision of the safety tunnel, to realize the design of the new cavern. The laboratory extension includes the construction of a 40 m long cavern with 300 m² cross section and two smaller tunnels connecting the safety tunnel and the existing laboratory to the new cavern. The minimum distance between the front face of the new LSM and the highway tunnel is about 25 m.The French and the Italian authorities, responsible of the exploitation of the Fréjus highway tunnel, asked the CNRS to develop an accurate study indicating that the construction of the laboratory extension would not have any negative impact on the existing structures of the highway tunnel. The main results of the developed study by Systra are summarized hereafter. The construction works should begin prior to the end of the construction works of the Fréjus safety tunnel in 2018."

Jan 1, 2016

By Yasushi Arai

"Among Tokyo Metro’s approximately 200km of subway lines, the Tozai Line that connects Chiba Prefecture and mid-Tokyo experiences congestion of up to 199% at worst and relief of this has become urgent. Therefore, as it is imperative to increase the number of trains operating in the exceptionally congested area from mid-Tokyo going east, a large-scale renovation work is planned between Iidabashi Station and Kudanshita Station that will facilitate turn-back via 3 tracks. While ensuring the safe and stable operation responsible for about 1.35 million passengers daily, this highly difficult work of inner wall demolition and reinforcement of the side walls and floor slabs will only be implemented for 3 hours during late night. This paper discusses large-scale plans to improve turn-back facilities, and the methods of construction therein as an example of operational improvement of a subway network. 1) INTRODUCTION The Tokyo Metro Tozai Line (“Tozai Line”) opened over the entire 30.8 km distance from Nakano to Nishi-funabashi on March 29, 1969. It has the longest operating length of the nine Tokyo Metro lines, and was the first subway line to extend past the borders of the Tokyo Metropolis. Through train services with two other railway companies are available from the Tozai Line. Tozai Line trains join the Sobu Line of the East Japan Railway Company (“JR East”) and the Toyo Rapid Railway Line of Toyo Rapid Railway (“TR”) from Nishi-funabashi Station, and the JR Chuo Line from Nakano Station. The line is structurally distinctive in that 51% of it was built using the open-cut method, 43% of it is elevated and the remaining 6% was built when we used the shield method for the first time 1)2)3)."

Jan 1, 2016

By A. D. Hammond

"INTRODUCTION The recent drop in iron ore prices has claimed an unwitting casualty in vanadium. Vanadium is dominantly produced as a co-product of steel production. The recent shutdown at EVRAZ’s Mapochs steel-vanadium operations in South Africa has cut-off 10% of the world’s vanadium output. Earlier in February, 2015, Australia’s Atlantic Ltd. suspended operations at its Windimurra iron-vanadium complex after a fire caused severe damage at the plant. Since then, challenging market conditions has resulted in the permanent closure of this operation. This decoupling of vanadium production from integrated iron ore producers presents an opportunity for vanadium exploration companies to target single-product deposits. This trend is manifested in the increasing number of pure-play vanadium ventures around the world.The mine production of vanadium is dominated by three countries namely, China, South Africa and Russia, which collectively produce 98% of the world’s vanadium. While the use of vanadium as an alloy in the steel industry remains by far the largest application for this metal, growth in demand is expected to come from the renewable energy industry in the form of batteries for energy storage. This paper summarizes the current state of vanadium exploration, briefly describes the vanadium market and lists sources of future demand for the metal. TREND IN VANADIUM EXPLORATION The most active participants in the current vanadium exploration are pure-play vanadium ventures in Brazil, South Africa and Australia. These ventures are targeting deposits with higher vanadium grade than those typically mined in titaniferous magnetite operated by integrated steel-vanadium producers. The 10% shortfall in vanadium production resulting from the shutdown at EVRAZ’s Mapochs is expected to be partially compensated by Largo Resources’ Maracás Menchen vanadium operation located in the State of Bahia in Brazil, which commenced operation in August 2014 and is expected to reach design capacity of 11,400 tonnes of vanadium pentaoxide (V2O5) by the end of 2015. The estimated production1 for 2015 is 6,500 tonnes of V2O5 at a target production cost of $3.60/lb. This is the first vanadium operation to be placed in production in the Western Hemisphere in over 35 years."

Jan 1, 2016

By Cheng Ang, Yun Bai, Zhi Liu

"This paper presents a conceptual design of an innovative tunnelling method named the Ring Pipe Jacking Method (RPJ) which is conducted by the Ring Pipe Jacking Machine (RPJM). The RPJM consists of a double ring shell which forms a ring section where small interlaced cutter heads or several micro tunnelling machines are assembled to cut soil. Similar to the conventional pipe jacking method, the RPJM also needs a thrust system, a slurry transport system, and a control system. To satisfy the need for large/super large or special section tunnels in future, the RPJM is designed to reduce sharply the excavation face to the annular section, thus enhancing the face stability. Part of the innovation is that the RPJM uses modular cutter heads or micro-TBMs which can be reused. The typical double shield shape can be easily changed by reinstalling the modular cutter heads. Modularity allows the tunnel to be cut in any cross-section shapes, ranging from a circular tunnel to a rectangular one. INTRODUCTION The demand and requirement to utilize urban underground space is rising with the rapid social development in recent years. It is necessary to reduce excavations of the urban ground surface to ensure smooth traffic in cities. Therefore the conventional open cut construction method for underground tunnels can no longer satisfy the need of practical engineering, and it is taken over by trenchless technologies .The Pipe jacking method is an important trenchless technology and is used more and more frequently to install underground pipelines, but the present pipe jacking method still has many problems. For example, it is not suitable for installing large-diameter tunnels and it also has difficulty in construction of short radius curved tunnels. This paper presents a conceptual design of an innovative pipe jacking machine named the Ring Pipe Jacking machine (RPJM) and introduces the correspondent Ring Pipe Jacking Method (RPJ) which can be applied to construct large-diameter tunnels. Furthermore, technical characteristics and superiority of the ring pipe jacking method are analyzed in this paper."

Jan 1, 2016

By Yiming Sun, David Tsztoo, Rick Nolting, Adam M. Wirthlin, Rebecca Fusee

"Excavation and initial support of the New Irvington Tunnel presented significant challenges, including rapidly changing ground conditions, heavy ground loads, and squeezing. Such behaviors were anticipated from historic tunneling records of the adjacent Existing Irvington Tunnel, and extensive site investigation, but clearer understanding of their actual extent and causes has resulted from convergence measurements, observations of ground behavior, initial support monitoring and detailed geologic mapping. Time-dependent movements, documented hours to months after excavation in clay-rich rock and in moderately to intensely fractured rock, identified squeezing areas, allowed classification by currently-used predictive methods and added to the list of lessons learned in tunneling such ground. INTRODUCTION In March 2003 the San Francisco Public Utilities Commission (SFPUC) authorized funding for the $4.6 billion Water System Improvement Program (WSIP) to repair, replace, and seismically upgrade its water system. The program consists of 35 local projects located within San Francisco and 48 regional projects located in several counties from the Sierra foothills to the San Francisco Bay Area. The New Irvington Tunnel (NIT), a key component of the WSIP, is located east of Fremont in Alameda County, on the east side of San Francisco Bay. The NIT is a new 18,660 foot (5,689 m), redundant tunnel, 190 to 670 feet (58–204 m) offset from, and subparallel to the Existing Irvington Tunnel (EIT). Built between 1928 and 1932, the EIT was constructed with an unreinforced cast-in-place concrete lining and is vulnerable to damage in the event of a major earthquake along the two closest active faults. The Hayward Fault is located less than a mile west of the tunnel, and the Calaveras Fault is located half a mile east of the tunnel. Although the alignment does not intersect these faults, the shaking and sympathetic displacement along secondary faults that cross the tunnel alignment are potential hazards. The NIT provides a seismically reliable water transmission facility capable of withstanding earthquake damage and maintaining continuous water service after a major earthquake. The NIT also adds system redundancy and provides for operation flexibility of running water through both tunnels, or through one tunnel while the other is out of service for inspections and maintenance."

Jan 1, 2016

By Pedro Alejandro Samané Tuni

El presente texto describe la metodología de investigación adecuada para la excavación subterránea a través de la clasificación geomecánica según: RMR (Bieniawski), Q (Barton), Romana, Deere y Palmstrom, quienes determinan los tipos de sostenimiento y el span de autosoporte para cada tipo de roca e influyen en el método adecuado de excavación según clasificación de excavabilidad. Sin embargo, no se encontró el método adecuado y solo se define cuál de estas clasificaciones son factibles de usar en la excavación de cada tipo de macizo rocoso.

Jan 1, 2016

By J. Noll, D. Yantek, B. Kendall, J. A. Organiscak

"A self-tramming remotely controlled mobile Dry Scrubber (DS) was developed by J. H. Fletcher and Co. under a contract with the National Institute for Occupational Safety and Health’s Office of Mine Safety and Health Research (NIOSH OMSHR) to reduce exposure of miners to airborne dust. NIOSH OMSHR laboratory testing showed that the DS averaged greater than 95% dust removal efficiency with the disposable filters and averaged 88% and 90%, respectively, for the optional washable filters in their pre-washed and post-washed test conditions. Although the washable filters could be reused, washing them generated personal and downstream respirable dust concentrations of 1.2 and 8.3 mg/m3, respectively, for a 10-minute washing period. The DS’s velocity pressure regulated variable frequency drive (VFD) fan maintained a relatively consistent airflow near the targeted 1.43 and 4.25 m3/s (3000 and 9000 ft3/min) airflow rates during most of the laboratory dust testing until reaching its maximum 60 Hz fan motor frequency or horsepower rating at 2610 Pa (10.5 in. w.g.) of filter differential pressure and 3.97 m3/s (8420 ft3/min) of scrubber airflow quantity. Laboratory sound level measurements of the DS also showed that the outlet side of the scrubber was noisier and the loaded filters increased sound levels as compared to clean filters at the same airflow quantities. With loaded filters the scrubber reached a 90 dB(A) sound level at 2.83 m3/s (6000 ft3/min) of scrubber airflow, indicating that miners should not be overexposed in relation to MSHA’s permissible exposure level (PEL) of 90 dB(A) at or below this airflow quantity (1). The DS’s washable filters were not used during field testing because of their lower respirable dust removal efficiency and the airborne dust generated from filter washing. Field testing the DS with the disposable filters at two underground coal mine sections showed that it can clean a portion of the section return air and provide about a 50% dust reduction at the face area downstream of the continuous miner (CM) operation. INTRODUCTION Coal mine worker overexposure to coal and quartz dust continues to be a problem at underground coal mining operations in the U.S. The U.S. Mine Safety and Health Administration (MSHA) recently changed the standard for coal mine worker respirable dust exposure from 2.0 mg/m3 average during an eight-hour shift to 1.5 mg/m3 average over the actual working shift, effective as of August 1, 2016 (1). If more than 0.1 mg/m3 quartz mass is found in the coal mine worker dust sample, the applicable respirable dust standard is further reduced to the quotient of 10 divided by the percentage of the quartz in the sample (1). Over 90% of the mechanized mining units operating in U.S. underground coal mines are continuous mining machines (2). MSHA inspector dust samples from 2009 to 2012 showed that 3.7% of continuous miner operators exceeded the 2.0 mg/m3 dust standard, while 8.8% of these dust samples exceeded the new 1.5 mg/m3 dust standard and 9.7% of these samples exceeded the reduced quartz standard (3). Additionally, roof bolter dust samples at these mechanized mining units during this same period have exceeded the 2.0 mg/m3, 1.5 mg/m3, and reduced quartz levels at 1.1%, 3.7%, and 10.6%, respectively (3)."

Jan 1, 2016

By Tsunenori Shibata, Kazunori Jimbo, Kaoru Toya, Masafumi Matsumoto, Jinya Mitsui, Toshinori Tsuji

"The Toyama Line is under construction as a natural gas pipeline with a length of 102 km from Itoigawa City to Toyama City. A 2 km-long tunnel section of the pipeline that we are reporting here is being excavated in a mountain area away from an urban area. The geology under which the tunnel is constructed is collapsible fractured breccia slate and Holocene sandy soil. Other tunnels of the Hokuriku Expressway and Hokuriku Shinkansen are in service above the tunnel route. From the starting shaft on Toyama side, conventional tunneling was adopted to facilitate excavating the base rock layer and maintain enough distance from the Hokuriku Expressway tunnel. From the starting shaft on the Itoigawa side, TBM tunneling was adopted to cope with the unconsolidated soft ground for a 200 m-long section from the shaft. We will discuss the issues and countermeasures concerning the selection of a tunnel route and excavation methods, performance of both conventional and TBM tunneling, and underground connecting of these tunnels excavated by conventional (NATM) and TBM methods under a high groundwater pressure up to 1.2 MPa. INTRODUCTION AND BACKGROUND The International Petroleum Exploration Teiseki Co., Ltd. (INPEX) is constructing a high-pressure main pipeline network in the Toyama Prefecture area to promote the use and reliable supply of natural gas as shown in Figure 1. As part of the Toyama line project that has a total length of 102 km, A-1 construction, the nearest section to the tunneling starting point in Itoigawa City, where various tunnel excavation methods have been adopted to install the high-pressure pipeline 20 inches in diameter, a 2 km tunnel in the A-1 construction section discussed here is to be excavated by conventional and TBM methods in a mountain area. Based on environmental studies such as traffic jams due to frequent traffic of heavy vehicles disposing of soil, and the effects of dust, noise and vibration during construction, we selected the route to install the gas pipeline in a mountain area as shown in Figure 2, where the impact on the surrounding environment could be minimized."

Jan 1, 2016

"Metallurgical process development in greenfield projects must define the comminution flowsheet and establish the equipment sizes that are required to deliver the project design criteria. These are critical steps that heavily influence the financial performance of the project, requiring a detailed understanding of the ore properties of the project resources and the best practice methods to size comminution machines. This paper reviews current practices for determining the ore characteristics relevant to comminution circuit design. Particular attention is given to the design of sampling and testing programs, and the methods commonly applied to size crushers and mills for conventional size reduction applications in mineral processing. IntroductionMetallurgical process development in greenfield projects requires the selection of a comminution flow sheet and must establish the equipment sizes required to deliver the project design criteria. This necessitates a detailed understanding of the ore properties that define the project resource. For brownfield projects the same objectives may apply for plant expansions, or the project objective may be simply to define the capacity and operating cost of an existing facility for a new ore source. The process development phase in either instance will typically comprise the following key activities:• Geometallurgical classification and sampling of the ore deposit or deposits.• Determination of comminution energy requirements.• Benchmarking similar projects.• Identification of flow sheet options.• Equipment selection and sizing.This paper is concerned specifically with process development testing and will as such focus on the first two activities on the list: sampling and testing of the deposit. The discussion will focus on testwork programs to support the design of comminution circuits commonly in use in mineral processing today, specifically crusher, tumbling mill and stirred mill technologies.It is important that any testwork program is designed giving consideration to the types of flow sheets that are viable for the project, and the data that will need to be generated to support the final equipment sizing. Designing a testwork program to only provide information about one particular type of flow sheet will not allow sufficient information to be generated for a rigorous trade-off analysis of options, and may therefore preclude financial optimization of the project. Testing programs should be designed to collect sufficient data to ensure that any backtracking at a later stage to fill in missing information is minimal."

Jan 1, 2016

By Brian Hart, Stamen Dimov, Aparup Chattopadhyay, Barun K. Gorain

"A novel gold deportment technique has been developed for complex copper-gold and double refractory gold ores using state-of-the-art technology. Characterization of these ores is a challenging task due to low copper and gold grades in ores, presence of both primary and secondary copper sulfide phases and variable proportion of visible and invisible gold in different sulfides and iron oxide phases.Double refractory ores are mainly composed of silicates and carbonates with moderate clay and mica, and minor amounts of sulfides and organic carbonaceous matter. Gold mostly occurs as ""invisible gold"" (sub-microscopic gold) as solid solution or as colloidal-sized particles in different sulfides and other phases. The dominance of invisible gold and presence of highly preg-robbing and finely disseminated carbonaceous matter adversely affects gold recovery in flotation and leach circuits. Characterization of this carbonaceous matter, commonly known as TCM and quantification of gold associated within TCM, along with different sulfide and oxide phases is highly complex and challenging.Studies were initiated on various complex ore deposits and also on samples representing various process streams. This paper presents the development of a systematic approach to diagnostic metallurgy using state-of-the-art optical and automated mineralogy techniques, namely, micro-probe, dynamic SIMS and TOF-SIMS analysis for quantification of invisible and visible precious metal content in various species. The relevance of the mineralogy characterization to metallurgy will also be discussed in this paper."

Jan 1, 2016

By S. Banisi, M. Maleki-Moghaddam

Direct observation of charge shape and its motion in industrial mills is not possible; therefore, a combination of analytical and physical studies is used to determine charge trajectory. Software packages, which predict charge motion consider only the outermost layer of charge (single ball) and ignore the charge and the interactions of grinding elements. In the new version of the GMT (Grinding Media Trajectory) software, the effect of liners specification and bulk load on charge shape and trajectory are considered. The charge trajectory was measured in a laboratory mill with the diameter of 100 cm and length of 21.5 cm with the transparent end and compared with that of the old version of GMT. Four types of polyurethane rings were accurately machined to scale down the liners arrangements at two industrial mills. The model mill was operated at 55, 70 and 85% of the critical speed for five levels of mill filling (10, 15, 20, 25% and 30% by volume). The experiments indicated that the end walls effect was negligible for the model mill with the length of 10.8 cm and beyond. The proposed relationships to correct the trajectory and charge shape were validated by using the new liner of the Gol-E-Gohar iron ore company AG mill. The positions of shoulder, toe, toe departure and impact points were predicted with the relative errors of 5, 0.7, 2 and 0.2%, respectively. The GMT software was updated with the new relationships. The results of GMT simulation indicated that when the lifter face angle increased from 7 to 30°, the distance between the charge impact point and the toe decreased from 40.1 to 11.2° for 30% filling. The change in the position of the impact point meant increasing the probability of charge impacting the toe, not the liner which favored more efficient comminution practice.

Jan 1, 2016

By H. Huang, R. N. Gow

"In Part I, Gibbs’ phase rule was applied to mass-balanced EH-pH diagrams for the Cu-As-S-H2O system. The diagrams were generated using the stoichiometry of enargite as a basis. In this study, the calculations were expanded to cover the stoichiometries of three other Cu-As-S minerals – tennantite, sinnerite and lautite – and compared with enargite. Stability regions within the resulting EH-pH diagrams were found to change with stoichiometry such that a particular mineral would predominate if its stoichiometry was used in the calculation. Solution speciation was also found to vary, with thioarsenate being the best example. This stoichiometric effect helps to explain results reported in the literature and would be difficult to realize if it were not for mass-balanced calculations. IntroductionA comprehensive thermodynamic review has been conducted on the aqueous copper-arsenic-sulfur (Cu- As-S) system (Gow et al., 2014, 2015a, 2016b; Gow, Huang and Young, 2016c). Data on the free energies of more than 100 species were collected from various authors, and thermodynamic databases collated to produce mass-balanced EH-pH diagrams using the thermodynamic equilibrium calculation software STABCAL (Huang, 2014). The full database is listed and discussed in Gow et al. (2015a). Diagrams were generated for enargite and confirmed with Raman spectroscopy using bulk mineral electrodes in order to identify reactions spectroelectrochemically. Theoretical calculations agreed well with the experimental results under alkaline conditions (Gow et al., 2015a), acid conditions (Gow et al., 2014) and alkaline sulfide leaching conditions (Gow et al., 2015b).In the present study, additional mass-balanced EH-pH diagrams were generated by changing the Cu-As-S stoichiometry from enargite (Cu3AsS4) to tennantite (Cu12As4S13), sinnerite (Cu6As4S9) and lautite (CuAsS). Regions for the thermodynamically stable species were shown to change with the four different mineral compositions. Potential leach conditions, both for co-dissolution and selective dissolution techniques, were examined for differences in predominant species according to changing copper-to-arsenic ratios, sulfur compositions and sulfur oxidation states."

Jan 1, 2016

By Sylvain Castonguay, Sylvain Pilon

"Operator competency is an important factor in the safe and successful operation of today’s complex processes. Competent process unit operators deliver superior performance and results. In greenfield projects, operator competency is particularly critical, as the lack of specific operations experience must be offset with proven practical knowledge and skills to avoid mistakes that can cost millions in terms of start-up delays, production losses and equipment damage. It is, therefore, important to know precisely what competencies are required for a project or site, and what any gaps in operator competency need to be addressed and improved. The success of plant commissioning, start-up and sustainable operations is directly tied to operator competency. The significant investments required for new projects, the exploitation of more challenging ore bodies, and the increasing complexity of plant operations have placed renewed emphasis on the need for competent operators. Furthermore, many large capital projects are being developed in remote regions, often with ties to the delivery of social benefits for the local population in terms of jobs, training and other development opportunities. While automation and processing technologies have helped do more with less, indicators now point to a bottleneck in human performance limiting operational results.Automation industry development in managing abnormal situations, including solutions for simulation and operator training, has produced applications to provide customized and flexible training methods. This paper will discuss tools to automate the operator competency process in order to guide trainers to effectively teach, measure, control, provide feedback, and monitor operator skills. Today’s competency management solutions can be effectively applied throughout the course of an operator’s professional life, as a guide to hiring new operators, for developing competencies to support operations, and also to develop and refine best practices and share lessons learned."

Jan 1, 2016

By Aysan Molaei, Kristian E. Waters

"Solvent extraction is the one of the most common techniques for recovering metal ions from aqueous systems. However, it is not efficient in the extraction of low concentration metal ions from aqueous solutions. Predispersed solvent extraction (PDSE) is an alternative method for solvent extraction which implies colloidal liquid aphrons as extracting agents in order to reach higher interfacial area and lower reagent consumption. This work investigated important parameters in PDSE of nickel ions from dilute aqueous solutions by fractional factorial design of experiments. Four experimental parameters, the initial extractant concentration, initial surfactant concentration, equilibrium pH and phase volume ratio (organic to aqueous ratio) were investigated. The important parameters were determined as well as important interactions between these parameters. It was found that extractant concentration, phase volume ratio, and equilibrium pH are the most significant experimental parameters. However, the interaction between surfactant concentration and other parameters was determined as significant interactions.INTRODUCTIONNickel is one of the key components found in cars, mobile phones, rechargeable batteries, kitchen appliances, and steel industry (Anyadike, 2002). It is one of the most important metals produced by Canada which is in the five top nickel producers in the world. Despite a 24% decrease in the nickel prices from 2011 to 2014 the nickel global mine production increased by 36% between these years (U.S. Geological Survey, 2015; Nickel - Statista Dossier, 2015), which shows the increasing demand for nickel. This high demand leads producers to consider the production of nickel from low grade ores and other secondary sources such as process wastewaters. The removal of nickel ions from process wastewater is also important due to environmental considerations. Nickel is known to be a human carcinogen and it may cause serious lung and kidney problems, pulmonary fibrosis, gastrointestinal distress, and skin dermatitis if it exceeds the critical level (Borba et al., 2006; Fu & Wang, 2011)."

Jan 1, 2016

By J. Szarkowski

"INTRODUCTION The Butte district of Montana is well-known as one of the biggest historic producers of copper in the world. It is also a classic example of a porphyry Cu-Mo system that has been overprinted by zoned, polymetallic (Cu-Zn-Pb-Ag) lode mineralization. After copper, silver was the next most important metal mined from Butte, with over 700 million ounces of total Ag production between 1880 and the present day. Although many papers have been written on the mineralogy of the early porphyry Cu-Mo mineralization and the high-grade Cu-rich lodes in the center of the district, relatively little information exists on the mineralogy of silver in Butte. The purpose of this paper is to summarize past and present silver production trends for the district, and to combine previously published work with new research to examine the mineralogy of silver in the Butte mining district. BUTTE HISTORIC SILVER PRODUCTION According to a recent USGS compilation1, Butte is one of the most Ag-rich porphyry deposits in the world, both in terms of average Ag grade (8.6 g/ton) and total production + reserves (Fig. 1). It is also the 2nd biggest Ag-producing mining district in the U.S. (after the Couer d’Alene district, Idaho). Annual silver and copper production data for the Butte district, compiled from various sources2,3,4, are summarized in Figure 2. Peak production of Ag and Cu was in 1917. While Ag production gradually declined in the ensuing decades, Cu production remained strong until the years leading up to the closure of the Berkeley Pit in 1982. In 1984, mining of the nearby Continental Pit resumed under a different operator, and continues to the present day. The Continental mine produced an average of 35,000 metric tons Cu and 575,000 oz Ag per year between 1984 and 20044. These figures do not take into account a period of mine closure in 2001-2003 due to an unexpected hike in utility prices. The long-term decline in Ag/Cu ratio of ore mined in Butte (Figure 3) is due to several factors, including: 1) changes in metal prices; 2) a downwards decrease in Ag/Cu ratio of most of the lodes with depth below surface; and 3) a shift in mining methods from selective underground mining of high-grade veins to open-pit mining of the bulk rock."

Jan 1, 2016

By Andrzej Luszczkiewicz, Magdalena Duchnowska, KGHM Polska Miedz S. A., Witold Pawlos, Jan Drzymala, Alicja Bakalarz, Przemyslaw B. Kowalczuk

Numerous data in the literature confirm that the chemical composition and consumption of grinding media influence electrochemical properties of flotation suspension as well as effectiveness and selectivity of upgrading processes. During a milling process, attrition of grinding media is observed. Depending on the susceptibility to abrasion, the grinding media influence, to a different extent, the redox potential, pH as well as flotation efficiency. As a result, different upgradeability of sulfide minerals is observed. The paper presents laboratory scale flotation results, obtained for the copper sulfide ore from Polkowice Region of KGHM Polska Miedz S.A. in Poland ground in the presence of forged steel, highchrome iron and stainless steel as the grinding media. The investigated flotation feed contained 36 g/t (ppm) of silver and 1.86 % of copper. Several flotation tests were conducted using fixed amount of frother and a mixture of sodium ethyl and isobutyl xanthates as the collector at three different doses of 75, 100 and 125 g/t. A comparison of the obtained results confirmed that the application of grinding media with different chemical compositions influenced the electrochemical properties of the suspension and recovery of silver and copper in the final concentrate. The highest values of redox potential were observed for the stainless steel as the grinding medium. Moreover, in the presence of this type of grinding media, regardless of the collector dosage, the best silver upgrading was observed. For the forged and high-chrome iron media, the recovery of silver depended on the collector dosage. It is indicated that higher levels of the redox potential, together with smaller amount of iron released from the grinding medium, improve the flotation of the silver-bearing mineral compounds from the copper sulfide ore.

Jan 1, 2016

By R. V. Fox, L. K. Sinclair, D. L. Baek

"In this study, rare earth elements were recovered from bastnasite concentrate and waste fluorescent lamp phosphors using supercritical carbon dioxide extraction with a nitric acid/tributyl phosphate adduct. Several pretreatment methods were used to alter the crystal structure of the source materials, and thus improve rare earth element recovery. Pretreatment methods included 1) dry roasting of the source material at 730oC, 2) decomposition with 50% sodium hydroxide solution at 150oC for 4 hours, and 3) decomposition with 12 M sulfuric acid at 300oC for 4 hours. Treated and untreated samples underwent supercritical extraction at 24 MPa and 65oC for 1 hour. Untreated bastnasite and phosphor samples showed <10% rare earth element recovery, but sodium hydroxide digestion resulted in >60% recovery for most rare earth elements. Dry roasting of the bastnasite concentrate was also effective, resulting in >60% recovery for cerium.INTRODUCTIONRare earth elements (REEs) consist of the 15 lanthanides, scandium, and yttrium. Scandium and yttrium are included because they are in the same group as lanthanum, appear in many of the same ore deposits as the rest of the lanthanides, and exhibit many similar chemical properties. REEs are used in a wide array of applications including electronics, magnets, catalysts, glass, and solid-state lighting (Xie, Zhang, Dreisinger, & Doyle, 2014). Because of China’s continued dominance of worldwide REE production, the United States Department of Energy has sought to diversify domestic supplies of REEs (United States Department of Energy, 2011). A key part of this strategy is the development of improved extraction methods for both ores and recycled sources.Supercritical fluid extraction (SFE) is a promising technology for extraction and separation of rare earth elements. Contact with an acid adduct dissolved in supercritical carbon dioxide allows for the rapid extraction of REEs from solid matrices. Supercritical CO2 has several potentially useful properties as a solvent, including high diffusivity and the ability to tune solvation properties by adjusting pressure. Such tunability may have applications in separating the REEs once they have been extracted from the solid phase. Tributyl phosphate/nitric acid adducts (TBP:HNO3) are a particularly promising class of adducts for SFE extraction of rare earth elements. Using TBP:HNO3 adducts in supercritical CO2, several researchers have successfully extracted REEs from their oxides (Wuhua, Pijia, & Yongjun, 2010; Zhu, Duan, Xu, & Zhu, 2009). However, there is a complication in applying this technique to many types of ores and recycled sources: REEs are often locked in refractory minerals which are resistant to acid attack, resulting in limited recovery in supercritical extraction."

Jan 1, 2016

By N. Weidner, V. A. Samaranayake, K. Awuah-Offei, S. Que

"This research sought to facilitate improved stakeholder (community) analysis using discrete choice theory (DCT). The work considered 16 project attributes and four demographic factors. The discrete choice experiment was conducted in Salt Lake City, Utah to illustrate the usefulness of DCT in mining stakeholder analysis. The data was used in discrete choice modeling of individual preferences. The approach answers three important questions for enhanced stakeholder analysis: (1) What are the factors that affect individual preferences? (2) What is the effect of demographics on individual preferences? (3) What is the value of environmental and social impacts to individuals in the community? INTRODUCTION Stakeholder analysis is crucial for effective stakeholder engagement because it is important to identify and characterize stakeholders in order to effectively engage in dialogue with them. This is not only true for all stakeholders but true for characterizing the members of a particular stakeholder. The local community is usually the largest and most diverse single stakeholder group. Also, the local community is perhaps the most important stakeholder group. Thus, analysis of the local community is essential for project management. Conventional mining stakeholder analysis is a three-step process, which involves evaluating: (1) each stakeholder’s view of the project (positive, neutral, or negative); (2) how influential each stakeholder is (high, medium, or low); and (3) how they will be impacted by the project (high, medium, or low) (ICMM, 2012). The results of this evaluation are documented in a stakeholder analysis matrix (Table 1), which is used to classify the stakeholders into three groups: highly influential supporter of the project, neutral about the project, and highly influential opponent of the project. This process can be used to describe groups of stakeholders (e.g. community, non-governmental organizations, etc.) or individuals making up a particular stakeholder group (e.g. members of the local community)."

Jan 1, 2016

By J. W. van der Merwe, A. S. Bolokang, M. J. Phasha, V. J. Matjeke, C. Moopanar

"Excessive wear rates on railway wheels can result in rolling-stock derailments. If wear is detected early the possible derailments can be prevented by prematurely replacing wheelsets, although the inventory cost and maintenance downtime remain a challenge. In the current study, wheels were introduced and monitored in-service for two years to investigate the cause of excessive wear rates. The wear rates and stresses were calculated for the wheels suitable for a maximum load of 26 t per axle. Microstructural and mechanical properties were analysed. As expected, the general microstructure of all the wheels tested was pearlitic. Although all the wheels complied with the tensile strength requirements, stress calculations confirmed material distortion on excessively worn wheels whereas trial wheels revealed yield strength exceeding the yield criterion. High wear rates observed on the wheels were a result of low yield strength relative to the load per axle. The typical wear mechanism found was due to a combination of rolling contact fatigue and abrasive brake wear. Despite compliance of the wheels with existing requirements regarding material and mechanical properties (hardness, ultimate tensile strength), it is recommended that the yield strength must also be taken into consideration as a critical parameter.IntroductionRailway wheels are used to support the wagon mass and guide the wagon along the tracks (Park, 1974). The wheels and rails must be able to tolerate the applied tangential forces in order to effect wagon dynamic performance and reduce material deformation (Ghidini et al., 1994; RSE_TE_SPC_0045, 2011; AAR M107/M 208 Specification, 2011. Over the past ten years, the South African coal wagon maintenance depot has experienced excessive hollow wheel wear rates on the heavy haul line wheels. The maximum load of Jumbo wagons on the coal line is 104 t, or 26 t per axle. Although the maintenance intervention cycle for wheelsets was two years, between February 2011 and August 2012 some wheels experienced excessive hollow wear. Hollow wear is regarded as wear exceeding 2 mm on the central portion of the wheel tread (RSE_TE_SPC_0045, 2011). This happened despite the fact that these wheels were manufactured and certified according to the requirements of AAR M107/208 standard for carbon steel wheels (AAR M107/M 208 Specification,. 2011) and the local wheel RS/ME/SP 021 standard specification (RS / ME / SP / 021 REV 5 (2013). The AAR standard only specifies a minimum hardness as a required mechanical property and the local standard specifies hardness and minimum tensile strength only. In general, an increase in hardness will improve the rolling/sliding wear resistance of steel. This relationship of hardness and wear resistance was found to be true only in a situation where solid and similar alloys are in contact (Singh, Khatirkar and Sapate, 2015). The sliding wear resistance of a material is usually estimated using Archard’s equation (Liu and Li, 2001)."

Jan 1, 2016

By Markus Papst, Denise Millier, Daniel Beckers, Axel Preusse

"At an open-pit lignite extraction mine in Germany, groundwater has to be pumped over a large area, which leads to subsidence at the surface. As long as the geology of the area of influence is homogeneous, the subsidence is uniform and has marginal influence on buildings.Since the geology of many regions is characterized by faults, there are different rates of subsidence along those faults, which can lead to considerable consequences. Those different rates of subsidence on both sides of a geological fault are associated with the structure of the geology and soil mechanical properties. Horizons with various thicknesses and types of soil are affected differently by the groundwater pumping because of the offset of the faults, and thus react dissimilarly to dewatering.The smaller the grain of the geological horizon, the stronger the chance of shrinking, which leads to a stronger effect at the surface; therefore, dewatering impacts on clayey soil are different to those on sand and gravel. Regions consisting of meadows with turf inclusions are endangered as well; compared to the surrounding geology, those areas react in an entirely different way to water removal, which leads to immense differences in subsidence.The differences in area and respective subsidence impacts, as well as if it is possible to localize those areas, is an issue which needs to be analyzed. Furthermore, detailed mapping can help in the development of future forecasts about those subsidence differences and can also help with monitoring geological faults. In the context of subsurface spatial planning, this mapping has to be kept under review medium- to long-term.INTRODUCTIONThe utilization of underground mining is of increasing significance and of high interest, both for the common good and for future generations. For decades, humanity has been extracting resources from the subsurface, and salt, coal, lignite and water - just to mention a few resources - have been extracted from underground (Sailer, 2013)."

Jan 1, 2016