Search Documents

By Z-P. Song, Z-B. Jiang, A-N. Jiang

"In deep excavations under conditions of high ground stress, even hard rock undergoes creep and other time-dependent effects that may result in instability. This study involves an analysis of the typical damage to the surrounding rock in the deep tunnels of the Jinchuan nickel mine in China. In order to understand the creep mechanism, triaxial creep laboratory tests were conducted under high stress. The creep characteristic curves and the Nishihara model parameters of typical rock were obtained from these tests. The numerical simulations, with which the creep model is developed, were performed using Flac3D. The creep model parameters were back-analysed on the basis of field monitoring data. Finally, appropriate support schemes for deep tunnels are suggested. The creep deformation of rock increases with time and axial load. At the same load level, the creep deformation of unloading is greater than that of loading. The simulated deformations of the surrounding rock are coincident with those from in situ monitoring, indicating the applicability of the presented rock creep model in situations of high ground stress. The results constitute a reference for support design in deep mining tunnels.IntroductionThe excavation of underground caverns can alter the natural stress field of the surrounding rock. In deep engineering projects under conditions of high ground stress, even hard rock shows obvious creep properties and time effects (Yao, 2005; Liu, 1994). The time effect of excavation not only causes decompression of the floor and increases sidewall stress, but also leads to stress concentration at the corners of the excavation, which influences the stability of the surrounding rock in a very complex manner.Many researchers have studied the creep properties of rock. ‘Griggs (1939) showed that creep occurs in sandstone, shale, and silty sandstone rock under the load of 12.5%–80% of the failure load.’ Subsequently, much research has been published on rock creep tests, including the uniaxial compressive creep test, the triaxial compressive creep test, the discontinuity rock shearing test, and field tests (Wawersik, 1974; Amadei et al., 1980; Okubo et al., 1991; Jin et al.,1995). A rheological model is used to describe the complex rheological deformation of material. This model is based on various fundamental parameters including rock elasticity, plasticity, and viscous properties, which can be combined into a constitutive model to reflect the rheological properties of various types of rocks. Wang et al. (2014) studied the creep– damage–rupture characteristics of rock salt by applying a creep-damage model. Munson (1997) developed a multi-mechanism constitutive model of creep of polycrystalline rock salt based on steady-state creep and modified it to incorporate transient creep through work hardening and recovery. An elasto-viscoplastic approach was developed to simulate the timedependent nature of the fracture zone (Malan, 1999). Rheological models were proposed to understand the collapse of iron ore mines in Lorraine by Dragan et al. (2003)."

Jan 1, 2016

By J. Lorengo, C. H. Bucknam

"Standardization of the Inductively Coupled Plasma Mass Spectrometry (ICPMS) method for gold in cyanide solutions was undertaken to provide a more sensitive method to quantify the gold content than the atomic absorption method standardized in 1994 (E1600). The gold concentration range covered is from 0.001 mg/L Au - 0.3 mg/L Au (0.00005 toz/t Au – 0.009 toz/t Au). Interlaboratory testing was carried out with the assistance of the American Society of Testing and Materials (ASTM) International on two committees to determine the within laboratory and between laboratory reproducibility. Three barren solutions from metallurgical operations were measured in triplicate to satisfy statistical requirements for Committee E1 on Analytical Chemistry of Metals, Ores and Related Materials. A synthetically prepared matrix representing the metallurgical processing solutions was used to prepare Youden pairs to satisfy the requirements of Committee D19 on Water. Results of the standardization program are presented. INTRODUCTION Analysis of process solutions for gold concentration requires accurate and sensitive analytical methods in order to manage process control and metallurgical accounting. Flame atomic absorption spectrophotometry (FAAS) has been the work horse of the assay lab for this duty for decades. In 1994 the FAAS standard method was approved by the American Society for Testing and Materials (ASTM) (1). Six process solutions were collected and preserved by measuring the pH and adjusting to greater than pH 10, if necessary. Duplicate solutions were provided to eight laboratories in random order for analysis by FAAS covering the gold concentration range of 0.19 µg/mL (0.006 toz/t.) to 10.7 µg/mL (0.312 toz/t). A high precision method was used, which involved bracketing the sample with the higher and lower standards nearest to its concentration repeating readings three times and averaging the results. The optimum precision for the FAAS gold method was found to be at the 1.00 µg/mL (0.029 toz/t) and lower scope limit 0.3 µg/mL (0.009 toz/t) gold concentration. Since tailings solutions typically have concentrations below the lower scope limit, use of ICPMS was developed at Newmont USA Limited (Newmont) to assay the lower range solutions."

Jan 1, 2016

By Guangdong Institute of Resources Comprehensive Utilization, Y. H. Tang, H. X. Hu, T. S. Dong, Z. H. Zhang

"A world class rare metals ore deposit in Africa belongs to a massive granite type poly-metallic pyrochlore-niobium resource. Successful project development in realizing the resource is vital to Africa’s economy and pyrochlore processing technology.The ore properties are quite complex due to the presence of varieties of valuable minerals, fine dissemination and intimate association of minerals and the relative abundance of easy-floatable minerals. The separation of pyrochlore from zircon, calcite and mica is generally considered difficult. Whilst studies have previously been conducted by several independent institutions overseas, no satisfactory process has yet been developed to date for the ore deposit—possibly due to the process designed being too complex; high cost of regents; lower performance.Based on process mineralogy study and extensive testwork, the authors have in recent years developed a new technology—“De-slime—Iron-rejection—Zircon (with calcite) and Calcite reverse flotation—Pyrochlore flotation”. The flow-sheet is characterized by ?1prior removal of slimes and iron minerals; ?2 Zircon (with calcite) and Calcite reverse flotation; and ?3Pyrochlore flotation applying new type of chelating collector GYX3 developed by GZRINM in conjunction with selected regulators and depressants.The process involved in the new technology is simple to implement and facilitates stable operation; the flotation reagent regime is easily adaptable; the cost of main reagent is lower largely because it is easy to manufacture and is environmental friendly. Laboratory test results demonstrated that, for raw ore assaying 0.35% Nb2O5, 0.03% Ta2O5 and 0.45% ZrO2, pyrochlore concentrate grade of >35% Nb2O5 could be obtained with >74% recovery. Meanwhile, the Ta2O5 content in pyrochlore concentrate could be recycled, and ZrO2 recovery >50% could be achieved in zircon concentrate assaying ZrO2>63%—significantly improving the technical-economic indicator. These results were verified in pilot trials of 1.44t/d throughput. The paper presents the new technology in whole, summarizes the key factors affecting its performance and discusses in simple terms the mechanism of separation."

Jan 1, 2016

By T. Krumins, L. Zunti, R. Frischmuth

"Titanium and titanium alloys are commonly selected for pressure oxidation autoclave vent piping and pressure control valve components, as well as autoclave internals and other process piping. In the autoclave vent application, titanium ignition risk is controlled by limiting oxygen concentration, and preventing high gas velocity gas impingement on surfaces. Oxygen concentration is dependent on the autoclave pressure and temperature operating conditions and therefore oxygen concentration and the associated titanium ignition risk is dependent on standard operating procedures, process control interlocks and permissive conditions. It is not uncommon for these standard controls to be deficient during atypical operating conditions, or for operations to deviate from the operating procedures, increasing the potential for a titanium ignition incident. Titanium ignition risk caused by elevated oxygen concentration in autoclave vent systems can be reduced with the introduction of an online autoclave overpressure calculation and the configuration of associated interlocks and permissive conditions. INTRODUCTION High temperature pressure oxidation (>190°C) is a well recognized and versatile metallurgical oxidative pre-treatment process commonly used to liberate gold from refractory sulphide ores and concentrates before conventional leaching with cyanide. Titanium and titanium alloys are highly corrosion resistant in pressure oxidation process conditions and are therefore commonly selected as materials of construction for many components including: autoclave internals, agitators, process piping, and components in autoclave vent systems. Operations that anticipate or have experienced aggressive corrosion in the vent system often have little choice in material selection other than the use of titanium (Krag & Henson, 1992). Titanium is not suitable for use with elevated oxygen concentrations and is considered a restricted material because of its high pyrophoricity and combustion propagation properties (Beeson, Smith, Stewart, 2007). Several serious incidents have occurred in which titanium materials have ignited in autoclave applications (Zawierucha, McIllroy, Million, 1995). In autoclave vent applications, titanium ignition risk is reduced by preventing elevated oxygen concentrations, maintaining low gas velocities, and minimizing the potential for gas impingement on surfaces. Oxygen concentration in the autoclave vapour phase and vent system is dependent on the autoclave operating pressure and temperature conditions and therefore titanium ignition prevention controls typically include process interlocks and operating procedures based on the selected nominal design operating conditions. However, it is not uncommon for these controls to be deficient or for operations to deviate from the nominal operating conditions over time, increasing the risk of titanium ignition. The introduction of an online calculation of autoclave overpressure and a maximum target autoclave pressure as well as associated process control interlocks and permissive conditions can alert the autoclave control room operator and prevent an elevated oxygen concentration from developing, and therefore reduce titanium ignition risk in autoclave vent systems."

Jan 1, 2016

By C. Eddine

"Can we use data to make communication effective? How does one successfully tackle the challenge of solving cultural differences and harmonizing the needs of diverse stakeholders while developing and maintaining a strong and reliable corporate image? Is it possible to achieve better engagement and minimizing risks with data? This paper aims to explore human rights and business procedures, the promotion of shared prosperity in a sustainable manner and the use of metrics to guide decision-making process. Among the topics examined are: • the significance of stakeholder engagement in community development projects; • the use of grievance mechanisms to give a voice to First Nations and communities / populations in vulnerable positions (including children and elders); • the benefits of configuring and implementing a feedback system in partnership with the communities. This research is a preliminary initiative and has limitations on the extent of the material used. The author acknowledges there is a vast amount of work and publications available on this subject, as well, as a variety of examples that have not been included. The intention is to keep developing this research to assess and expand how data can be used to minimize risks and improve engagement, in addition to inspire others to continue advancing this topic. Natural resources consumption is a reality that will not disappear in a foreseeable future. Several developments and operations are located in remote areas where communities in vulnerable situation and Indigenous Peoples live. Feedback systems are being ratified as a tool to help tackling the challenges of harmonizing cultural differences and fulfilling the needs of diverse stakeholders. Integrating social, environmental, and economic values plays an imperative purpose in preserving a productive and trustworthy relationship with stakeholders. Positioning social standards next to environmental and economic principles shows inclusiveness and firm intention of integration. We add value to a positive image of our industry by embracing responsibility for corporate actions and promoting their beneficial impact on the environment. The social context within communities, groups and organizations is dynamic and presents new challenges as connections evolve. There are wildly diverse expectations which one may need to address during exploration, construction and operating phases. Disagreements are an inevitable consequence of interactions due to the different needs and requirements of the parts involved. Nevertheless, balancing differences and solving conflicts can offer remarkable opportunities for improvement."

Jan 1, 2016

By Xianglin Yang, Hong Zhong, Jingjing Xiao, Guangyi Liu

"The selective adsorption of a flotation collector to a mineral plays a crucial role in enhancing the hydrophobicity of targeted mineral particles for attaching air bubbles in pulp. The recent progress of the structure-reactivity relationship of flotation collectors, the characterization methods for mineral surfaces with adsorbed collectors and their commercial application are reviewed in this paper. Particular emphasis is placed on the density functional theory (DFT) for understanding the reactivity of new collectors, the surface analysis techniques including time-of-flight secondary ion mass spectrometry (ToF-SIMS), in situ scanning electrochemical microscopy (SECM) and atomic force microscope (AFM) to characterize mineral/collector interface, and the flotation technologies for optimizing recovery of valuable minerals. Especially, the recently developing collectors such as Gemini, alkoxyalkylthiourea, dithiourea, amide-hydroxamate and oximido-thiol surfactants, and their specificity to given minerals are evaluated. Based on this crucial review, it is evident that the structural modification approaches for minerophilic or hydrophobic groups, and combined surface analysis approach for further understanding the adsorption mechanism of collectors on mineral surfaces will lay a solid foundation for the future development of flotation collectors. INTRODUCTIONIn mineral processing, flotation is the main process for separation and recovery of valuable minerals from the ores contained them (Fuerstenau et al., 2007). One of the key requirements in flotation process is to increase selectively the surface hydrophobicity of the targeted minerals by collector adsorption so that these mineral particles can preferably attach to air bubbles in a slurry or pulp (Fuerstenau et al., 2007). Flotation collector is a kind of functional surfactant, which is composed of polar and non-polar groups (Somasundaran, & Wang, 2006). Non-polar portion, commonly being linear, branch or ring hydrocarbon group, is termed hydrophobic group. The polar portion, exhibiting strong affinity to mineral surfaces, is known as minerophilic group (Nagaraj, 1988). According to mineral types including saline, oxide and sulfide minerals, flotation collector divides into sulfide and oxide mineral collectors. For efficient recovery of valuable minerals from the refractory complex ores, insights into the adsorption mechanism, hydrophobic model and subsequent flotation approach of flotation collectors have been regarded as an indispensable issue in mineral processing."

Jan 1, 2016

By Jason Saldanha, Andrew Evans, Jonathan Baber

"INTRODUCTION The need for a new road crossing at Silvertown is the result of three key drivers:- •,Severe congestion and delay at the Blackwall Tunnel and surrounding road network; •,A lack of network resilience and reliability resulting from a lack of alternative road crossings in east London and the impacts of unplanned closures; and •,The need to support substantial economic development in east and south-east London (jobs and homes) These drivers directly informed the main objectives for a road-based river-crossing solution. The traffic-related problems at Blackwall Tunnel are long-standing and before Transport for London (TfL) assumed control for the strategic road network in London in 2000 the Department for Transport (formerly Dept of Transport) had investigated various relief options including a third tunnel bore and new bridge. This resulted in a new crossing alignment being safeguarded (by direction of the Secretary of State for Transport) and this was refreshed in 2001 in favor of TfL. In recent years (since 2009) TfL as part of the East London River Crossings Programme has undertaken detailed optioneering and feasibility work to address the above ‘need’. This led to the conclusion that a new road tunnel would offer the best solution in preference to bridge, ferry or demand management options. In 2012, in response to a formal request by the Mayor of London, the Secretary of State for Transport confirmed a new road crossing at Silvertown as a Nationally Significant Infrastructure Project (NSIP) by Section 35 direction under the Planning Act 2008. This NSIP designation meant that TfL as scheme promoter must comply with the National Rail and Road Networks National Policy Statement (NNNPS) and must seek the necessary powers to build and operate the crossing by means of a Development Consent Order (DCO) under the Planning Act 2008."

Jan 1, 2016

By E. Maritz

"The localized uniform conditioning (LUC) technique was proposed by Marat Abzalov in 2006. The technique converts conventional uniform conditioning (UC) grade-tonnage curves into single grade values attached to each smallest mining unit (SMU). This is achieved by ranking the SMUs within a panel in increasing order of their grade (based on the direct kriging of SMUs). This ranking is then used to localize the conventional UC grade-tonnage curves for each panel by dividing them into classes and computing their mean grades, which are assigned to the SMUs. The quality of this localization process will depend heavily on the validity of the grade patterns predicted by the direct kriging of the SMUs. Abzalov noted that where the distribution of data available for the direct kriging of the SMU is characterized by strong short-range variability, the advantages of using the LUC approach may be more limited. Consequently, a study was undertaken to determine how valid the predicted grade patterns of a typical Birimian-style gold deposit (with high nugget effect and strong short-range variability) might be expected to be. This was determined by comparing the direct SMU kriging ranking (based on sparse data) with the grade control model ranking (based on close-spaced data and the best available estimate of the deposit). The results showed a satisfactory correlation between these rankings and it was concluded that, although the grade patterns predicted by the direct kriging of the SMUs may be less meaningful for deposits exhibiting strong short-range continuity, there is nevertheless a convincing relationship with the actual (or best available) rankings. Therefore, the LUC technique is still considered to be useful for this style of deposit. IntroductionFor adequate technical and financial evaluation of a project, attempts should be made to estimate the recoverable resources – the portion of the in situ resource that can be economically extracted by mining. To achieve this, the estimates of the tonnage and grade of the mineralization should be produced above a given economic cut-off and should take into consideration the proposed mining selectivity."

Jan 1, 2016

By D. K. Sarkar, Ying Huang

"Superhydrophobic thin films were fabricated on aluminum alloy substrates by chemical etching followed by passivation with organic acid molecules; (ii) electrophoretic deposition (EPD) of functionalized ZnO nanoparticles and (iii) electrodeposition of organic-inorganic composite materials. The physical and compositional analyses of the deposited thin films were characterized by SEM, FTIR, XRD as well as contact angle goniometer. The contact angle and surface roughness of the superhydrophobic surfaces prepared by the chemical etching process were found to be 156° and 2.29 µm, (ii) by the EPD process were found to be 155° and 4.54 µm and (iii) by the electrodeposition process were found to be 159° and 7.11 µm, respectively.The corrosion properties were analyzed with both polarization and electrochemical impedance spectroscopy (EIS) in NaCl aqueous solutions. The results demonstrate that the superhydrophobic thin films on aluminum alloy substrates display better anti-corrosion behavior than the as-received aluminum substrate. The comparison of results pertaining to the compositional and corrosion properties of these thin films on aluminum will be discussed in this work.INTRODUCTIONSuperhydrophobicity is defined as a surface property which provides non-wetting characteristics with a water contact angle larger than 150°. It is observed that the creation of certain micro-nanoroughness structures promotes the entrapment of air in the spaces of the rough surface morphology. In addition, lowering the surface energy helps to reduce the affinity of water drops to the surface, thereby weakening the water-surface interaction. Recently, various fabrication methods for superhydrophobic surfaces have been explored (Sarkar, 2010, Huang, 2010, 2011, 2013, 2015a, 2015b), such as the sol-gel process (Brassard, 2011), plasma treatment (Marchand, 2013), chemical vapor deposition (Zheng, 2009), chemical etching (Saleema, 2011), electrodeposition (Ying, 2011) and electrophoretic deposition (EPD; Huang et al., 2015b)."

Jan 1, 2016

By José Ricardo Lopes, Alaor Coelho, Marco Gomes, Alfredo Dacio Moraes Filho, Akira Koshima

"Very low strength alluvial peat soil was found under two old drainage galleries with just 4.3m cover above a twin tunnel due to be excavated by a 10.6m diameter EPB Shield for São Paulo Metro’s Line 5. Alignment was required to strengthen soil and drive the TBM through safely without damaging the galleries. The design included six levels of self-drilling forepoling with lengths up to 15m, using 100 mm-diameter SCH160 metal tubing and injection bulbs with estimated 0.20m diameter. Two 6m-diameter circular shafts were excavated along the shield-tunnel axis, one each side of the galleries, and forepoling fanned out under gallery foundations. Given the peculiar soil and confined working space, more data were needed for correct drilling geometry. Ground mass treatment was successfully designed and executed and galleries were fitted with instruments to enable the shield’s advance. DESCRIPTION São Paulo Metro’s Line 5 (aka Lilas or purple line) is adding 11 stations along an 11.5km extension and three EPB TBMs are being used simultaneously (three EPBs on the same job for the first time in Brazil) with one of them excavating a large cross- section twin-track tunnel. Currently the largest work-in-progress for São Paulo Metro, this project has been divided into seven lots and 9km are already operational. This study refers to Lot 6 where the 10.6m - diameter EPB shield excavation is only 4.3m below two galleries running through a 10m layer of very soft peat soil in an old alluvial riverside region ringed by major roads. After recent filling, this area (Parque das Bicicletas) was used for recreation, although temporarily it has become a construction site. This paper will describe the original basic design; precautions in relation to the structural condition of the galleries after inspection; the problem of absence of data for their foundations; subsoil bore tests; evolution of the engineering design for the galleries and conditioning and reinforcing the soft soil below the galleries to ensure safe advance of the EPB shield, and finally the successful outcome of the solution used."

Jan 1, 2016

By E. Larsen

Marine tailings disposal may in some cases be the best solution to one of mining’s major environmental problems. The public standing of this solution is poor, partly because of past bad practices. Among the tailings problems spreading of super-fines and toxic substances stand out. The two are often interrelated as heavy metals, insoluble to sea water, tend to adsorb on fines and spread piggyback on them. Only one paper seen, has addressed the mineralogy of fine particles in suspension. The topic was a secondary tailings deposit. Studies on the sedimentation of fines in large river estuaries show that different minerals sediment sequentially as the salinity of the river increase. Mineralogy in the particle size range where particle separation takes place, has so far, naturally been in focus for the mineral processors. Next to nothing is known about the fines which may cause environmental problems. Tailings disposal has, due to its complexity, to a large extent been taken over by specialists in other fields, biologists, engineering geologists, chemists. The basics of the subject ought also to be given more input by the mineral processing community. A drawn out battle about tailings discharge into some fjords has taken place in Norway. The detractors focus at fine particles (could be dangerous nanoparticles) spreading and emphasize the effects. Calculation is simple: 5 million tonnes tailings annually discharged, containing 1 wt. % < 1µm determined by laser diffraction, results in 50 000 tonnes of nanoparticles let loose in the environment. The industry`s difficulty to answer, is lack of basic research on this topic. Test work to develop a methodology to address the problem is described. One thing the mineral processors know is that final tailings may be comprised of tailings from separate separation processes, with different properties, some of which may require special treatment. One tailings stream from a Norwegian mine is investigated in such a context.

Jan 1, 2016

By Yong Yuan, Wenhao Xiao, Luc Taerwe

"The static shear stiffness of an immersion joint subjected to combined compression and shear forces is investigated by experiments in a test set-up. To explore the performance of the immersion joint, the compression-shear loads, which are applied on a specimen according to test protocol, are determined based on real design situation. In this test, the main focus is on the steel shear keys and the rubber sealing. For the applied loading schemes, different levels of axial force, corresponding to the water depth of the joint, are considered as well as the changing amplitudes of the shear force. The force-displacement curve is obtained and the hysteresis is observed during the whole test. The joint‘s static shear stiffness is calculated, showing to increase linearly with respect to the magnitude of the axial force. Moreover, it is found that the rubber sealing has a significant influence on the shear behavior of the joint. INTRODUCTION An immersion joint is the connecting part between two adjacent elements of an immersed tunnel. Compared to that of the bulk elements, the stiffness of the immersion joint is relatively small. When it is subjected to shear actions, whether resulting from vertical foundation settlement or horizontal earthquake movements, shear-resistance of the joint is the main concern for a safe and reliable water-proof design. A flexible immersion joint, which normally consists of a rubber seal and shear keys installed at an element end is a common solution in practice. The way in which the shear keys and the rubber seal behave in the joint together is of vital importance to a comprehensive understanding of the shear behavior of the joint. However, in literature very few experiments on the shear behavior of immersed joints are available although the flexible joints are applied in practice for more than 50 years already. O. Kiyomiya (2004) carried out both a 3-dimensional experiment and a finite element analysis for a new type of flexible joint referred to as the Crown Seal. The results indicated that this new type of joint can be applied in practice because of the effective reduction of lateral deformation. A linear model was found in the paper of Anastasopoulos et al. (2007) to describe the behavior of the shear keys, which consider that the stiffness of the shear keys tends to infinity. R.S. van Oorsouw (2008) discussed the shear capacity of concrete shear keys in segmental joints, by analyzing the influences of reinforcement and friction force between shear keys."

Jan 1, 2016

By C. Heckman, M. S. Moats, A. Luyima, W. Cui

"Chloride ions and their interactions with two organic smoothing additives – Cyquest® N-900 and HydroStar® 4208 – during copper electrodeposition were explored using cyclic voltammetry and electrochemical impedance spectroscopy. The results revealed that chloride ions, up to a concentration of 40 mg/L, depolarized the copper deposition reaction. A combination of chloride ions and Cyquest N-900 inhibited the depolarization reaction during copper electrodeposition. It is proposed that the chloride ions acted as bridging ligands between copper and Cyquest N-900. Addition of HydroStar at a concentration of 2.5 mg/L depolarized the copper deposition reaction when no chloride ions were present. This behavior did not change with the addition of chloride ions at the concentrations tested, indicating that chloride ions and the polysaccharide do not interact.IntroductionElectrowinning is a major production method used to obtain high-purity copper. In modern tankhouses, copper is electrodeposited onto stainless steel blanks and then stripped, washed and bundled for delivery. Significant improvements in the quality of electrowon copper have been made over the last few decades. Additives, temperature, current density, electrolyte concentrations and agitation are known to influence the quality of copper electrodeposits (Jenkins and Eamon, 1990).The influence of chloride and organic additives on copper electrodeposition has been the subject of considerable research. The addition of small quantities of chloride and organic additives has been recognized to significantly improve the properties of copper electrodeposits. These additives are critical in the prevention of dendrite growth and the production of smooth, dense cathode deposits.Chloride ions have been reported to catalyze the copper reduction reaction and assist in the production of uniform deposits (Lakshmanan et al., 1977; Sun and O’Keefe, 1992). Moreover, it is generally agreed that chloride ions depolarize the copper deposition process at low (several millimolar) chloride concentrations. This is because chloride ions catalyze the reduction of copper (II) ions to copper (I) ions (Cu2+ ? Cu+ + e-) in the rate-limiting step of this process (O’Keefe and Hurst, 1978; Ilgar and O’Keefe, 1997; Hebert, 2005; Shao, Pattanaik and Zangari, 2007)."

Jan 1, 2016

By Yoginder Paul Chugh, Jason E. Tinsley

"Over the last five years, the authors have compiled a database of Short Encapsulation Pull Test (SEPT) evaluations from Interior Basin (Basin) coal mines. Typically, SEPT data are analyzed to obtain peak load carrying capacity per unit length of resin encapsulation designated as the ""Grip Factor,"" or GF. In a previous paper, ""An Analysis of Short Encapsulation Bolt Pull Test (SEPT) Data From Interior Basin Coal Mines,"" authors analyzed tangent value of the load-displacement curve as Anchorage Stiffness at 50% (AS-50) of the peak load, or GF value, to assess reinforcement potential of an installed bolt system. This paper attempts to correlate the secant AS VALUES (of SEPT on 6 ft (1.8 m) long installed bolts at a lower load of about four tons from several different mines in the Basin with their MSHA-approved primary support requirements. Since the current regulatory environment requires plan changes dynamically to ensure that roof falls are minimized, the authors hypothesize that the practiced roof control plan must meet the minimum requirement of adequately supporting immediate roof strata. The analyses are based on 181 SEPT studies performed by Minova professionals. Analyses indicate a macrolevel correlation for both roof support density and roof support cost that may have the potential to be used by mine operators to compare their performance with other mines in the area. Limitations of the analyses include ignoring mining depth, mining height and required secondary supports as part of the requirements for a roof control plan. The authors recommend additional analyses to develop this concept further to develop guidelines that can be confidently used by coal companies.INTRODUCTIONPartially- and fully-grouted bolts are extensively used in coal mines for roof support as part of MSHA-approved roof control plans. Since grouted bolts have a larger area of contact with the rock, they can develop much greater anchorage capacity than conventional expansion shell (point-anchored) bolts. Load transfer characteristics and interaction mechanics between steel rebar, grout and rock mass around the bolt hole for grouted bolts are generally assessed in the laboratory or field though short-encapsulation pull tests (SEPT), which have been extensively researched by Aziz and Jalalifar (2005), Aziz (2004a), Serbousek and Signer (1987), Signer (1990), and Mark et al. (2002), among others. In a SEPT, about 12 in. (30 cm) of bolt length is typically encapsulated in resin and a pull test is performed to collect load-displacement data prior to failure and, in some cases, post-failure. A typical load-displacement data set for a bolt is shown in Figure 1. SEPT characteristics are designated by peak load carrying capacity, or grip factor, which is the peak load carrying capacity per unit length of resin encapsulation. SEPT is routinely used to assess anchorage performance characteristics of different lithologies overlying a coal seam to identify type of bolt, bolt diameter, length and spacing across and along an excavation. Anchorage stiffness, or AS, at any load may also be calculated as the tangent or secant value of the slope of the load displacement curve at a particular load level. Anchorage Stiffness characteristics of bolts from SEPT data have typically not been considered in any depth until recently (Chugh et al., 2014; Chugh et al., 2015)."

Jan 1, 2016

By C. K. Chabedi

"This paper discusses the difficulties associated with the potential exploitation of the deep multi-seam resources east of the Daarby fault in the Waterberg coalfield. The resources occur at a depth greater than 250 m and the thickness of the coal is roughly 110 m, but the top 50 m comprises coal intercalated with shale and the bottom 60 m contains five seams with sandstone and shale partings. Various factors affecting multiple seam mining at these great depths are discussed with reference to lessons learned from local and international experience on multi-seam mining. Field geological and geotechnical data was utilized to assess the stability of the roof of the seams. There is no specific rock mass rating for the Waterberg area, therefore approximate coal mine roof rating (CMRR) values were used to propose appropriate support strategies. Analysis of Multiple Seam Stability (AMSS) was used to analyse the strength of the parting or interburden between the various seams, the mining sequence, and the interaction between the various seams.The research indicated that it is possible to mine seams with a low CMRR at high mining rates using longwall mining, although support for gateroads is expected to be expensive, time-consuming and onerous to install, and will impact gateroad development rates. It will not be possible to simultaneously mine zones in close proximity and failure of the interburden is predicted, thus dangerous mining conditions are anticipated. However, it will be possible to mine just two of the eleven zones using longwall mining. IntroductionThis paper discusses the difficulties associated with the potential exploitation of the deep multi-seam resources east of the Daarby fault in the Waterberg coalfield using bord and pillar and longwall mining. Figure 1 illustrates the location of the Waterberg coalfield relative to other coalfields in South Africa, while Figure 2 shows the areas containing deep and shallow resources. The Waterberg resources are expected to contribute to South Africa’s future energy requirements, and are currently exploited at the Grootegeluk open pit mine. Grootegeluk produces coal mainly for a power station, with the higher quality product supplied as metallurgical coal. The deposit is technically unique and challenging, being a multi-seam coal deposit with a total of 12 seams over a thickness of 110 m as shown in Figure 3, including Zone 5. There is currently limited knowledge on the multi-seam mining of the deep Waterberg resources. Multi-seam mining utilizing the bord and pillar method has been practised in South Africa before, but at a depth of less than 100 m in the Witbank coalfields. Multi-seam mining in thin seams has also been performed in the Natal coalfields at a depth of less than 160 m, but mostly using bord and pillar mining and secondary mining (partial pillar extraction)."

Jan 1, 2016

By Maciej Wrobel, Joerg Hammerschmidt, Dana Nurgaliyeva, Alexandros Charitos, Jochen Guentner

"Smelting of copper concentrates in the flash smelter generates a flue dust stream that contains a substantial amount of copper and accumulates more than half of the arsenic input to the smelter. In view of its high copper content flue dust recirculation to the flash smelter is common practice. Globally traded copper concentrates are affected by ever increasing arsenic contents and cause an increasing circulating arsenic load in flash smelter operation. Control of the arsenic level in the smelter slag becomes a challenge. This interaction of arsenic loaded copper feedstock, need for flue dust recirculation and slag quality control call for possibilities to reduce the arsenic load of the recirculated flue dust stream.The technology of partial roasting is known from pre-treatment of copper concentrates before smelting, and gold concentrates before cyanide leaching, to remove the harmful element arsenic. The partial roasting technology can be adapted for use in the purification of the flue dust. A major challenge for flue dust treatment is its extremely fine particle size compared to usual concentrates. For this reason Outotec developed a new process, which allows handling of such fine flue dust. This process solution provides an efficient possibility to reduce the arsenic burden in copper smelter operations.The suggested process aims at reducing the arsenic load to the smelter by treating the flue dust prior to recirculation to the smelter. The presented results are based on test work in the Outotec R&D-centre in Frankfurt. It is possible to remove 80-85% of the contained arsenic and to collect it in an arsenic trioxide residue with a concentration above 90%. The final off gas contains SO2 from decomposition of sulphates that are contained in the flue dust. The off gas stream is relatively small. We assume that it is possible to combine the off gas stream with other smelter process gas streams and to treat it in an existing sulphuric acid plant. Coal is used as fuel and as reductant to reduce pentavalent arsenate to trivalent arsenite. Arsenite can be kept in gas form at temperatures above 450°C. This permits separation of a calcine stream with arsenic levels of 0.2 – 0.3%, which is recirculated to the furnace.Outotec has a wide range of roasting testing facilities from lab-scale to pilot-scale. Outotec has both capability to modify and adapt technology to specific ore or concentrate requirements, but also the necessary infrastructure in its research centers in Frankfurt and Pori to do appropriate validation tests in lab and pilot scale size plants."

Jan 1, 2016

By Osamu Nishikokura, Jumpei Yamashita, Darrell Liebno, Malcolm Sheehan

"The Eglinton-Scarborough Crosstown Project builds a 19km LRT corridor that includes a 10km underground portion, between Keele Street and Laird Drive. The West Tunnel Contract (ECLC1-15) includes 6.5km of twin EPB TBM bored tunnels with a 5.75m internal diameter precast concrete segment lining (PCTL), between Keele Street and Yonge Street. This paper summarizes the overall scope of work, the technical challenges faced and innovative solutions developed by the contractor during the TBM move across an existing subway tunnel using state of the art high capacity strandjack gantry crane.1. PROJECT OVERVIEW The Greater Toronto and Hamilton Area (GTHA) is Canada’s largest urban region, populated with over 6 million people, and is one of the most rapidly growing regions in North America. One forecast estimates that the population of this region will increase to 8.6 million by the year 2031. In September 2008, Metrolinx, an agency of the Government of Ontario, launched a 25-year regional transportation plan named “The Big Move” to cope with the expected increase in transportation demand. The Eglinton-Scarborough Crosstown, one of the projects included in “The Big Move”, is a light rail transit (LRT) that will run across Toronto in an east-west direction between Mount Dennis and Kennedy along Eglinton Avenue. In October 2012, the West Tunnel Contract of the Crosstown LRT (ECLC1-15) was awarded to Crosstown Transit Constructors (CTC), a joint venture between Obayashi Canada Ltd., Kenny Construction Company, Kenaidan Contracting Ltd. and Technicore Underground Inc. The project includes approximately 6.2 km long twin bored tunnels, 9 cross passages, 1 emergency exit building, 7 sets of station headwalls, and an intermediate pair of extraction and launch shafts. Each of 6.5 km long twin tunnels are divided by the existing subway station into two drives: the first half from the launch shaft LS-1 (west of Keele Station) to the extraction shaft ES-1 (west of Eglinton West Station), and the second half from the launch shaft LS-2 (east of Eglinton West Station) to Yonge Station, as shown in Figure-1. The TBMs are extracted at ES-1 and moved to LS-2 over the existing Yonge-University Subway Line at Eglinton West Station before resumption of tunneling at LS-2."

Jan 1, 2016

By T. Flitton, R. Peattie

"The extreme depths and consequent expense of drilling and sampling the gold-bearing reefs of the Witwatersrand Basin have resulted in limited data being available for estimation of grade ahead of the mining face. There is, however, a wealth of information from mined-out areas of these deposits. This estimation challenge resulted in the development of a unique method of Mineral Resource estimation.AngloGold Ashanti (AGA) utilizes a technique termed macro cokriging (MCK), which allows for the integration of the limited advanced borehole data with the large chip sample data-sets from the previously mined-out areas by adopting a Bayesian geostatistical approach. The MCK process, in short, is the estimation of mixed support size data together with the application of four-parameter distribution models.The gold value estimation for the Carbon Leader Reef (CLR) on the AGA TauTona Mine is used in this paper as a case study of the process and to demonstrate the effectiveness of this technique through production reconciliation. The current method has been proven over the last 20 years and is now an established part of the Mineral Resource evaluation process within AGA.IntroductionOwing to the extreme depths of the goldbearing reefs at the AngloGold Ashanti (AGA) Witwatersrand operations and the prohibitive expense and time involved in drilling boreholes to the required depth, only limited drilling and sampling data is available ahead of the mining face. Whereas traditional estimation techniques are interpolative, within the Witwatersrand the estimation is primarily extrapolative, with the majority of the data being sourced from the mined-out areas. This significant challenge to estimation resulted in the development of a unique method of Mineral Resource estimation and evaluation."

Jan 1, 2016

By Hatch, A. Reple, W Valery

The mining industry is facing declining feed grades which require the mining and processing of larger volumes of material per tonne of product. Pre-concentration aims to remove barren material at as coarse a particle size and as early in the process as possible to reduce processing costs, energy consumption, water losses, and greenhouse gas emissions while increasing production and profitability. This may be achieved using bulk ore sorting—the separation of barren gangue from a fully loaded conveyor belt based on the grade as measured or inferred from a sensor. This paper evaluates the technical and economic viability of bulk ore sorting for the PanAust Phu Kham copper deposit in Lao PDR. Bulk ore sorting technology is described briefly along with discussion of appropriate sensor and diversion systems for the Phu Kham operation. To evaluate the economic implications, the actual mined material and costs from 2014 were used as the base-case. Sampling data was not available; therefore, the ore grade variability that would feed a bulk ore sorter was estimated using geo-statistical tools based on mine grade control data. The sorter performance when treating this material was simulated considering the accuracy of the sensor measurement and errors associated with material diversion. The impact on inferred cash flow was estimated for several different scenarios considering the additional costs for sorter operation and reject handling. The evaluation demonstrated that bulk ore sorting at Phu Kham has the potential to increase the amount of metal in product and/or reduce processing plant throughput (and costs) to improve the annual inferred cash flow for the conditions investigated. The sorter is the gatekeeper – only material above the cut-off grade (value-adding) reports to the processing plant; no waste dilutes the feed. Likewise, above cutoff grade material is not lost to waste; preventing lost revenue.

Jan 1, 2016

By Brian McInnes, Joseph A. Sopko, Behzad Khorshidi

"The Port Mann Main Water Supply Tunnel involves a 1km long tunnel beneath the Fraser River from Surrey to Coquitlam, BC. At depths of up to 60 m below ground, the earth pressure reached 6 bar. The tunnel is constructed using an EPB TBM and gasketed precast concrete segmental liner. The tunnel and two shafts were constructed in a variety of soil conditions ranging from soft to stiff clays and silts, to compact to very dense sands and gravels. After approximately 800m of mining, a very dense and highly variable soil group consisting of cobbles and boulders halted the TBM. Several options were considered to stabilize the TBM face so an intervention could be conducted. Although de-watering was considered, there was risk of settlement to the Port Mann bridge piers, which was within 500m of the tunnel. Hyperbarics were also considered, however, the cost, schedule and uncertainty of the work that needed to be done, made it a risky option. Ground freezing by Liquid Nitrogen was chosen as the best solution, which would provide a frozen block around the face of the TBM. A temporary platform on the river was designed and constructed to enable drilling and installation of the freezing pipes and temperature monitoring equipment. The operation required close coordination among the tunnelling, marine and freezing sectors. Following the intervention, the TBM successfully broke through the reception shaft, and the remaining project was completed. This paper describes the design, construction and operational approaches used for the freezing and serves as a basis for future projects requiring expedited ground freezing."

Jan 1, 2016