Search Documents

By L. A. Sandbak, Yan Xing

"The purpose of this study is to evaluate the rock mass stability around the tunnels by three-dimensional (3-D) numerical modeling. Complex geological and tunnel features have been included in the model using the software package 3DEC™. Based on the available information on stratigraphy, geological structures, and mechanical properties of rock masses and discontinuities from the underground mine, 3-D stress analyses were performed on various cases with different K0 (lateral stress ratio) values, constitutive models, as well as support systems. Relations between these factors and the distributions of stress, displacement, and failure zones around the tunnels were obtained and discussed. Finally, comparisons between the field deformation measurements and numerical simulations are used as validations for the simulations, helping to determine the appropriate K0 value and material constitutive models for the underground mine.INTRODUCTIONThe case study site is an underground mine in the USA with a monthly ore production between 20,000 and 30,000 tons. The regional geology of the mine is structurally and stratigraphically complex. Rocks in the area include carbonaceous mudstone and limestone, tuffaceous mudstone and limestone, polylithic megaclastic debris flows, fine-grained debris flows and basalts, all part of the Cambrian-Ordovician Comus formation and related dikes. Both the mineralization and faults have general orientations striking N-S to NW-SE with high dip angles. The ore body in the mine has an incline of about 25---45 degrees located in relatively low quality rock; hence, cut-and-fill mining has been used.This underground mine has two vertical shafts used for ventilation, ore hoisting, and for personnel and material transportation. Development drifts were designed and driven to extract and transport the ore, as shown in Figure I. Bolts, mesh, and shotcrete have been applied in this mine for ground control. In order to reach various locations, the tunnel system is designed with different heading directions and inclines, which will be described in detail later. The area selected for modeling is a cubic region including all the tunnels inside the black square (Figure 1)."

Jan 1, 2016

By Michel Ruel, Ali Soltanzadeh, Benjamin Légaré

High fidelity commercial process simulation packages can be used at different stages of a greenfield project, from initial plant design to operator training in the later stages. However, there are several factors that make the software less attractive for small and medium size brownfield projects, such as the licensing cost and the fact-finding manpower required for model design and simulator maintenance. In this paper a different approach is described. The knowledge gathered from operating personnel was used to implement higher level models based on plant data, operating heuristics, and experience rather than detailed component-level models. The computing platform used was a low-cost, well-established, control system vendor-independent software. Throughout this paper we demonstrate the success of implementing this model-based approach using two industrial examples. The first example is a simulation of the carbon monoxide (CO) distribution system at a metallurgical complex. The purpose of this simulator was to test new control strategies and PLC programs prior to implementation. CO being a toxic combustible gas, validation of the suggested control system changes was necessary for plant safety. Simulation of specific operating conditions helped alleviate concerns and improved plant-wide acceptability of the new operating philosophy. The second example is a boiler simulator at a petrochemical plant. The operator training simulator (OTS) was designed as a platform for experienced operators to practice handling rare or abnormal conditions. A customized medium-fidelity model was developed for this targeted application where the cost of a full scale high-fidelity model could not be justified.

Jan 1, 2016

By Paul Sainato

Recruiting and retaining students in the explosives industry is becoming increasingly important each year. With no undergraduate degree in explosives engineering currently available in the United States, it is from other industries and degree disciplines we must recruit. The 2014 annual ISEE conference saw the first anonymous online survey distributed to members of SEE student chapters of the International Society of Explosives Engineers. The survey contained questions about future job and career plans, ideal job placement, expectations of salary and current academic degrees. The purpose of the survey was to determine what these students expect or require from a career in the explosives industry, and their current path to pursue this. This information can help steer recruitment activities and job offers for graduating students. The success for both student response rates and interest from the industry has allowed space for a yearly update of this survey. A second survey was distributed in 2015 and included international students. This paper provides the data from a third online survey distributed to all student members of the International Society of Explosives Engineers, globally. Understanding the main incentives for a student to accept a graduate position as an explosives engineer can help us, as an industry; position ourselves to remain competitive in recruiting against other major degree disciplines.

Jan 1, 2016

By C. Birch

"The purpose of this study was to establish the impact of discount rates on cut-off grades for narrow tabular gold deposits as characterized by the goldfields of the Witwatersrand Basin in South Africa. There are various methods available for determining the cut-off grade, from simple breakeven calculations to sophisticated software packages that consider a variety of inputs to optimize the cut-off grade. For this study a simple financial model was created in Microsoft Excel® that links the ore flow, block listing, and the cash flow. This allows the cut-off grade to be optimized considering how the cost of capital and chosen discount rate affect the cash flow.The discounted cash flow (DCF) and resultant net present value (NPV) are a widely used valuation method for production properties according to the South African Code for the Reporting of Mineral Asset Valuation (SAMVAL Code). The financial model in this study utilizes the Solver function, as well as simple Microsoft Excel spreadsheet formulae to optimize the NPV. Solver was chosen as it is a standard feature in Excel and thus no additional software costs are incurred beyond the basic Microsoft Office suite. For the purpose of this study, just narrow tabular gold deposits of the Witwatersrand Basin were considered. An example of a typical ore block listing, as well as the costing figures, was obtained from an operating gold mine. The results obtained from the study financial model were compared to the current cut-off grades obtained from the mine using their proprietary optimizer program, and were found to be comparable. The methodology utilized for this study thus appears valid.The cut-off grade was optimized considering the cash flow, which includes the variable mineral resource royalty tax, the variable gold income tax, as well as the discount rate. By comparing the resultant NPVs using discount rates of zero, 9%, and 12%, the impact of the discount rate on cut-off grades, resultant life of mine, and average mining grades (AMG) could be compared for the example ore block listing. The South African Code for Reporting of Exploration Results, Mineral Resources and Mineral Reserves (SAMREC Code) does not require operations to state if a discount rate was considered in determining mineable reserves. Mining companies approach the question of applying discount rates in determining their cut-off grades, and thus mine planning strategy, in different ways. Due to the negative impact that optimizing purely on NPV has on the life of mine, some choose to optimize only on profit. Other companies have reverted to utilizing pay limits as their primary grade planning strategy. The calculated cut-off grade is then considered to be another planning indicator rather than a hard determination of mineable reserves."

Jan 1, 2016

By J. Jin, J. D. Miller

"Bubble attachment at hydrophobic surfaces is of critical importance in the flotation recovery of mineral resources and fundamental experimental results have been reported in the literature describing the details of film thinning, rupture, and displacement. Now, for the first time, bubble attachment phenomena are examined using Molecular Dynamics Simulations (MDS). The simulation involves a nitrogen bubble containing 906 nitrogen molecules in a water phase with 74,000 water molecules at the hydrophobic molybdenite (001) surface. During the simulation period of 1 ns, film rupture occurs and the nitrogen bubble attaches to the molybdenite (001) surface, resulting in a contact angle of about 90o. In contrast, the film is stable at the hydrophilic quartz (001) surface and the bubble does not attach. Contact angles, determined from MD simulation after stabilization of the three phase line of contact, are reported and these results agree well with experimental and MDS sessile drop results. In this way, film stability and bubble attachment are described with respect to interfacial water structure for surfaces of different polarity. For example, the interfacial water molecules for the hydrophobic molybdenite (001) surface have relatively weak interactions with the surface when compared to the hydrophilic quartz (001) surface, as revealed bythe presence of a 3 A water exclusion zone at the molybdenite/water interface. INTRODUCTIONAttachment of air bubbles to mineral particles is of fundamental importance in understanding flotation separation phenomena. It is well known that attachment of an air bubble at a hydrophobic surface includes film thinning, film rupture, and film displacement (Somasundaran, 2006; Wilson, Adlard, Cooke, & Poole, 2000). Experimental techniques, such as high speed video, can catch the process of bubble attachment at a mineral surface (Drelich & Miller, 2012; Niecikowska, Krasowska, Ralston, & Malysa, 2012). However, molecular scale information to examine the phenomena has not yet been reported."

Jan 1, 2016

By M. Maccagni, J. Nielsen

"The recovery of lead from battery paste has been investigated for a long time and with the use of many different electrolytes. A number of processes have been presented, but none of them reached even the demonstration step. Engitec has developed a new concept for the battery paste electrowinning using a chloride electrolyte fed through a very innovative flow cell. The process has passed the lab and the demo scale and it is ready to be introduced on the market. In this paper, a description of the process will be provided.INTRODUCTIONThe need for improved energy storage systems as well as the introduction of commercially viable electric vehicles is providing a strong compulsion toward the research of new batteries. The lead battery is playing an important role because it is inexpensive, reliable and it is the most recycled material. This last aspect marks the lead acid battery as quite peculiar making it both the primary lead based product and the main raw material for lead production.In the last years the legislative pressure has become very strong and has forced the lead production to react through the introduction of important process innovations and market changes. The dispersive products, such as additives for paints and for fuel as well as bullets, have been practically banned all over the world while the battery market continues to grow. The lead acid battery remains the cheapest and most integrated energy storage system available and is improving to meet the new technical challenges. This is testified by the news coming from the development of new and more efficient lead acid batteries which are confirming their leading position.Unfortunately, the image of lead is very negative in the public opinion and some important actions are required to try changing this sentiment. Among them, better information to the market and users and the introduction of new and cleaner technologies in the production of lead can help."

Jan 1, 2016

By M. Javier

"Mining makes civilization possible. It also creates socio-environmental liabilities forcing us to ask how much more of this mining can our planet support. It is clear that the future of mining differs from mining in the future. The laws of nature are being compromised by mining. This paper studies the problems at the core of the mining business which need to be addressed. What kind of mining will serve our existence with nature on this planet? What kind of mining perspectives are we able to formulate without having negative effects for future generations? Is mining technologically sustainable? The values of predictions, imagination, and creativity must be integrated to define what mining should be. Those values should be in the technologies necessary to restoring equilibrium of nature (Geomimic) as well as in complete extraction of metals, better utilization of the mineral reserves, and design the usage of metals to recycle. The purpose of this research is to examine many views and perspectives for future generations and to accelerate the pace of innovation of having mining without socio-environmental liabilities by design and by understanding nature. KEYWORDS: Geomimic, Sustainability, Waste mine Design, Management by Loss. INTRODUCTION The future of mining is being stifled by many antiquated and stagnant attitudes and policies by the industry and society as a whole. The time is now or never for real action and education against these attitudes and to upgrade them to meet the current needs of this planet if we are to survive. Doing this will prove that we understand and respect nature for us and our posterity. It will also show a positive assessment that the mining process can be reversed before the point of no return. And that is to say, only if reversibility is still an option. It may not be anymore but it’s worth a try. We need to use our imagination and engineering know-how to come up with new proposals to change the core of mining. It would entail re-engineering. There is a profound difference between the future of mining and mining in the future. The future of mining is the continuation and persistence of past practices in the industry and expecting new results. Mining in the future requires a paradigm shift for extraction through modern thinking about mining as it pertains nature. The new paradigm for mining in the future would restore equilibrium with nature. Always keep in mind the connection of mining to nature. What is the future of nature? To predict mining in the future we need to use past experiences in mining and our knowledge of modern science and engineering to formulate a prototype that will enhance mining while maintaining equilibrium with nature. Mining and protecting nature are not mutually exclusive. This new prototype has nothing to do with the level of bonding or insurance that the mining industry can legally provide. The goal of this paper is to contribute some new ideas to help transform the mining industry based on the laws of nature and its limitations. Using this new prototype we will develop the following 1. Extraction of minerals Reserves-Dimensions-Technologies 2. Usage of mineral resources-Manufacture’s products designed to be reused and recycled 3. Nature- Equilibrium (physical, chemical and biological)"

Jan 1, 2016

By T. Copland

"The decreasing availability of resources amenable to surface operations has led to increasing numbers of underground mines, with trends indicating this will continue into the future. As a result, there is a need for additional optimization processes and techniques for underground mines, with many analogous methods having already been developed for surface mining. Current methods for design and optimization of stope boundary selection and scheduling mainly involve heuristic methods which focus on a single lever. Individual optimality may be approached, but globally optimal results can be obtained only by an integrated, rigorous approach. In this paper we review previous methodologies for stope boundary selection and medium- to long-term scheduling and highlight the need for an integrated approach. Previous integrated approaches are reviewed and an improved modelling system proposed for shorter solution times and greater applicability to mining situations. Randomly generated data-sets for gold-copper mineralization are used to investigate the model performance, describing solution time as a function of data complexity.IntroductionThe increasing need for mineral resources is driving an increase in underground mines. Lower grade mineralization with larger amounts of overburden is becoming economically viable due to technological advances; however, the software and tools available for strategic underground mine planning are not well developed. Advances in the methods used to determine underground layouts and scheduling must occur to ensure underground mining is as optimized as open pit operations, as underground mining involves many more technical restrictions.The process of determining stope boundaries and scheduling is an example of an aspect of underground mining amenable to optimization (Topal and Sens, 2010). The current industry standard for medium- and long-term planning for sublevel stoping (SLS) is to exclusively determine stope outlines and then determine an appropriate sequence and schedule accordingly. This process violates the concept of optimality as integrating the constraints imposed by pre-determining stope outlines does not allow for considerations in scheduling to influence boundary planning (Ataee-Pour, 2005). An integrated planning process that combines both stope outlines and scheduling would approach the optimal solution and hence generate more value for operations. This investigation specifically deals with the underground sublevel stoping (SLS). Other underground mining methods such as block caving, sublevel caving, and room and pillar mining have unique characteristics and therefore require specific stope boundary/production scheduling considerations."

Jan 1, 2016

By Mary Kama, Kaul Gena

"Magnetic skarn ore (MSO) is one of the major copper bearing ore extracted by the Ok Tedi Copper Mine in Papua New Guinea. Copper minerals are recovered by flotation while the iron not associated with copper are discarded as tailings. The objective of this investigation was to determine the iron ore reduction kinetics for the Ok Tedi MSO and ascertain if it can be processed to produce sponge iron for a mini steel plant in Papua New Guinea.SEM-EDAX analyses of the Ok Tedi MSO indicated 10.1% C, 30% O, 0.6% Mg, 1.1% Si, 21.1% S, 0.8% Ca and 36.2% Fe. Most of the iron is in sulfide form. Both naturally occurring and roasted sinters of Ok Tedi MSO samples of different particle sizes were reduced by charcoal carbon at three different temperatures and seven different reduction times. Analyses of the reduced products indicated a metallic iron content of more than 65 wt.% on average.Results showed that there was no significant difference in reduction between fluxed and control materials. Only a slight increase in kinetics with reduced particle size, hence the reaction rate constant (K) did not vary much within the temperatures investigated. Reaction kinetics increases with increasing reduction time at 900°C. Therefore, more iron reduction is observed with particles of 106 µm size. In addition, the results also confirmed that the reduction energy used was higher at 800°C and lower at 1,000°C. In summary, iron reduction can be improved but close monitoring of temperature and reduction times are essential to determine the reaction kinetics of the Ok Tedi MSO. INTRODUCTIONMost mines in Papua New Guinea mine large quantities of iron in the form of sulfides, carbonates, oxides and sulfates that are eventually disposed off as tailings. The Ok Tedi magnetic skarn ore (MSO) contains a significant amount of hematite, magnetite, siderite, ilmenite and pyrite that can be a source of iron. The mineralogical compositions of Ok Tedi MSO reveals more iron minerals than copper, yet all iron containing minerals are collected in the tails from the main copper production stream. Therefore, this study is conducted to investigate the possibility of producing direct reduced iron (DRI), or sponge iron, from the MSO. Such sponge iron may serve as the feedstock for electric arc/induction furnace based mini steel plants in Papua New Guinea."

Jan 1, 2016

By J. F. Strunk Jr., K. M. Maestas, Y. Chai, R. Legrand, R. L. Henry

"Groundwater with elevated sulfate and metals was treated using a sulfate-reducing pilot PRB consisting of a series of six 55-gallon drums filled with ZVI (Fe0), wood chips, brewer’s grain, limestone, and emulsified vegetable oil (EVO). Sulfate was reduced from >3000 to <250 mg/L and Cd, Cu, Mn, Ni, and Zn concentrations declined up to 3 orders of magnitude in 2 months. After 6 months of operation at a 7.5-day retention time, sulfate broke through. The system was then rejuvenated by injecting EVO in each drum and operated for 5 more months at a 9-day retention time. Sulfate-reducing bacteria in the pilot system grew by 3 to 4 orders of magnitude in 2 months. Some cementation of the PRB media was observed in the first 2 drums after processing 25 pore volumes of water, due to preferential upstream precipitation of sulfides; this can be avoided through operational modifications. Resulting permeability losses were estimated at 0.1% to 1% per year. Absorption/desorption was tested at bench scale to evaluate the use of various oil-soaked sorbents as a slow-release source of dissolved carbon. The tests show that oil sorbents can increase the useful life of a PRB between oil refills to over 100 pore volumes. INTRODUCTION High sulfate concentrations, low pH, and dissolved metal exceedances are common characteristics of mining-influenced water (MIW). Above-ground such MIW is commonly treated using biochemical reactors (BCR). In a BCR, water generally flows vertically downward through a layer of biomass, such as wood chips, manure, etc. The dissolved organics resulting from the decay of this material are oxidized first by microbes using oxygen; when oxygen is exhausted, other bacteria can use nitrate, and then sulfate to oxidize organics. Sulfate-reducing bacteria (SRB) reduce sulfate to sulfide, which quickly reacts with metals to form largely insoluble and stable metal sulfides. These reactions can be summarized as follows:"

Jan 1, 2016

By E. Ghali, A. D. Bas

"Treatment of oxide, e.g. roasted gold ores has received relatively less attention than sulphidic ones and recently, handling of oxide gold ores is becoming essential. In this study, the influence of roasted gold ore (RGO) slurry (at 35% solid ratio) on the electrochemical dissolution of gold has been examined using pure gold and iron oxide minerals (hematite, maghemite, and magnetite) as disc electrodes by zeroresistance ammeter mode either in one or two separate containers. The presence of slurry decreased galvanic currents, i.e. corrosion rates due to the release and increase in the amount of soluble and/or insoluble species that could retard further the anodic behaviour of gold. Higher galvanic currents were observed in two separate containers than that in one container indicating the primary importance of galvanic interactions. SEM-EDS results observed iron hydro/oxide coatings on gold surface in case of magnetite test. However, in case of RGO electrode it is not a perfect passivation, although somewhat decreasing trend was observed on gold dissolution. These findings have revealed that passivation is not only a laboratory phenomenon, but also it could be responsible for the slowdown of gold dissolution in industrial practice.INTRODUCTIONThe cyanidation of gold is an electrochemical corrosion process thus; the dissolution of gold can readily be studied by electrochemical techniques. The outcome/summary of previous electrochemical studies of gold leaching can partially be summarized as follows: Filmer (1982) and Lorenzen and van Deventer (1992) reported the negative effect of pyrite and pyrrhotite on gold leaching due to the galvanic interactions; Aghamirian and Yen (2005) studied gold galvanic corrosion in presence of sulphide mineral electrodes only in one cell using zero-resistance ammeter (ZRA) mode; Dai and Jeffrey (2006) discussed, individually, the anodic and cathodic behaviours between gold and sulphide minerals, and Azizi et al. (2010, 2011) used a bed reactor to examine the influence of sulphide minerals on gold dissolution in one and two separate cells. Accordingly, a slowdown in gold leaching has generally been attributed to the passivation phenomenon, although the indication of this phenomenon is still an undergoing debate. For instance, Mrkusic and Paynter (1970) identified the passivation as the film formation of dissolved species from calcine, Crundwell (2014) explained passivation, in the case of corrosion of metals, as the formation of a layer which is composed of a new chemical species on the mineral surface and this layer inhibits or blocks further reactions. He suggested that passivation is related to the oxidation of the metal, and the formation of a passive layer that retards the rate of dissolution by several orders of magnitude. Consequently, galvanic interactions, passivation phenomena, or combinations of them are considered significant electrochemical factors affecting gold dissolution (van Deventer, Reuter, Lorenzen, & Hoff, 1990; Azizi, Petre, & Larachi, 2012). It is important to note that generalizing the influence of a mineral/metal on gold dissolution may not be correct in all cases, since contrary behaviours/results (for pyrite) have been observed (Aghamirian & Yen, 2005). Therefore, electrochemical study of gold is still a subject of research and need to be examined further in detail."

Jan 1, 2016

By Tim Langmaid, Steve Skelhorn, Stephanie Robillard, Allen Mitchell

"The Port Mann Main Water Supply Tunnel project provides a critical water main crossing of the Fraser River for the owner, Greater Vancouver Water District (Metro Vancouver). The project consists of two 60-metre-deep slurry panel shafts and a 1-kilometre-long, 3.5-metre excavated diameter tunnel located near Vancouver, British Columbia, Canada. The initial tunnel lining is a precast concrete steel fiber reinforced gasketed segmental lining. The final lining is a 2.1-metre-diameter welded steel pipe. This paper describes the challenges encountered during tunnel construction and the solutions implemented. Key challenges include earth pressure balance tunnelling at up to 6 bar pressure—the highest to date in Canada—a water-crossing without surface access for the majority of the tunnel drive, ground freezing from a river platform for a critical TBM intervention, and boring through cobbles and boulders in dense glacial till. INTRODUCTION Metro Vancouver supplies drinking water to 18 municipalities, one electoral district and one treaty first nation, serving a population of more than 2.4 million residents. Water is collected in three mountainous watersheds to the north of the Greater Vancouver area, in southwestern British Columbia, Canada. To supply the growing demands of Metro Vancouver’s customers, treated water must be conveyed across two significant water bodies: the Burrard Inlet and the Fraser River. The existing Port Mann water main is one of several key links between the watersheds north of Vancouver and the municipalities south of the Fraser River. The Port Mann Main Water Supply Tunnel (PMMWST) is the first of a series of upgrades, to increase capacity, enhance scour protection, and improve seismic resilience. The new tunnel is 3.5 metres (11.5 ft) in diameter and 1 kilometre (0.6 mi) long. When completed, it will contain a new 2.1 metre (7 ft) diameter steel water main that will help ensure the continued, reliable delivery of drinking water to these municipalities, and will more than double the capacity of the existing 1.2 metre diameter main."

Jan 1, 2016

By A. Ehsani

"Seas and oceans constitute about 70% of the earth’s surface. They contain an enormous stock of various mineral resources such as sedimentary (marine placers), massive sulfide ore deposits, manganese nodules and cobalt-rich ferromanganese crusts. Sea and ocean floor ore deposits could well contribute to the meeting of ever-rising demand for raw materials in the metal industry. In this regard, more research and development in science and technology appear to be required to ensure maximum benefit from the mineral resources of seas and oceans. Since the 1960s, a variety of mineral and metallurgical processes have been studied and developed to deal with marine ores and to extract metals such as gold, nickel, copper, cobalt, manganese, tin, platinum group metals (PGM), zirconium, thorium, etc.In marine environments, there are many parameters which can affect the selection of the mineral and metallurgical processes. These include the extent and grade of the deposit, mineralogical and chemical properties of the deposit, and physical properties of minerals present with particular reference to particle size distribution and mineral liberation size.In this paper, we briefly review the latest trends in processing and extraction of marine mineral resources. Mineral processing technology is mostly applied for recovery of precious metals i.e. gold and PGM, in particular, from marine placers. In general, pre-treatment (sizing, classification, dewatering), gravity concentration techniques (shaking tables, spirals, jigs, etc.,), flotation, magnetic, and electrostatic separation are the options for enrichment of marine placer ore deposits. In the case of massive sulfides, manganese nodules/cobalt-rich crusts, hydrometallurgical and pyrometallurgical methods (as proven technological methods) can be exploited for extraction of metals from concentrates after physical separation or directly from marine ores. The hydrometallurgical treatments involve acid (e.g., sulfurichydrochloric) and alkaline (e.g., ammonia) leaching with different reducing agents and pre-treatments such as roasting. Alternatively, pyrometallurgical treatments involve mostly smelting, chlorination and segregation processes."

Jan 1, 2016

By Zhang Wei

"Pulang Copper Mine is located in Shangri-La county, Diqing Prefecture, Yunnan Province, with currently defined copper reserve of 4.8 million tonnes of copper metal and an average grade of 0.34% Cu. The mineralized zone in a dome shape is 2,300 m long, 600–800 m wide, and 1,000 m high. At present, the project is at a construction phase, with a first-stage mining and processing capacity of 12.5 million tonnes of ore per year. Ore haulage is planned via a drift and ore pass development system. The cavability of mineralized rock is classified into three types (II, III, IV), with type III accounting for more than 98% of the total reserves. The cavability of the orebody is generally considered to be good and block caving mining method is planned. Semi-autogenous grinding and ball milling are adopted for the mineral processing. The tailing dam construction method is a center-line method.INTRODUCTIONAs the China's largest underground nonferrous mine, Pulang Copper Mine is located in the northeast of Shangri-La County, Diqing Prefecture, Yunnan Province, China. It is 62 km northeast of Shangri-La city. Shangri-La County is a Tibetan-dominated, multiple-ethnic region, with a population of approximately 163,000 in 2009. The county is rich in mineral and water resources, thriving with tourism. Its economy is also dominated by agriculture. To date, the defined copper reserves at the Pulang Copper Mine is 4.8 million tonnes of copper metal at an average grade of 0.34% Cu. In addition, it contains a gold reserve of 145 tonnes, a silver reserve of 2,754 tonnes, a molybdenum reserve of 0.19 million tonnes, and a sulphur reserve of 10.5 million tonnes. The first-stage mining and processing capacity is planned at 12.5 million tonnes of ore per year. When it ramps up to this production rate, the mine will produce copper concentrate containing 50,000 tonnes of copper and molybdenum concentrate containing 968 tonnes of molybdenum. A drift and ore pass system is planned for ore haulage and mining method is a block caving method. Semi-autogenous grinding and ball milling are considered for mineral processing. A center line dam is adopted for the tailing dam construction (Feng, 2010; Feng, Li, & Wang, 2011; China Enfi Engineering Corporation, 2014)."

Jan 1, 2016

By A. Boehm

"For recycling LD slag into the steel making process, the phosphorous containing calcium silcate phases have to be removed from iron oxide phases. One possible technical solution could be magnetic separation in a wide range of susceptibilities from ferromagnetic to paramagnetic. To check the feasibility of magnetic separation the distribution of the magnetic susceptibility in size classes as well as the liberation of the phosphorous containing phase were evaluated by a new method combining two dimensional physical property analysis with QEMSCAN analysis. The particle size classes of energy controlled comminution products were subdivided into fractions of defined magnetic susceptibility using a hand magnet of well known field properties (pick up method). On the one hand the susceptibility classes were wet assayed on the other hand analyzed by QEMSCAN followed by data evaluation using iDiscover 5.3.1(FEI), which was adapted to the data structure of two physical properties (size and magnetic mass susceptibility). The results allow the comparison of mass based (3D) cumulative distribution of grades from the wet assays with the area based (2D) distribution from QEMSCAN analysis, in order to control a systematic (size dependent) stereological error for this special type of material. As the physical separation property forms a crucial parameter the results from the liberation analysis by QEMSCAN can be interpreted more profound with respect to an expectable separation result. Once the various mineral compositions of the particles are assigned to the physical properties the Henry Reinhardt chart serves to predict the best possible separation result and thus the feasibility of a separation technique.INTRODUCTIONThe two Austrian steel plants operated by voestalpine AG produce about 650,000 t (voestalpine 2014) of LD slag in the course of steel production from pig iron according to the basic oxygen process blowing oxygen in the converter by an oxygen lance. The process is also known as the Linz Donawitz (LD) steelmaking process. By the addition of lime (CaO), carbon, phosphorus, silica, manganese and sulfur, which are present in the molten pig iron, shall be oxidized and bound in the slag either as oxide or silicate phases, or leave the slag in the gaseous phase (CO). The average chemical composition of the investigated LD slag is given in table 1."

Jan 1, 2016

By P. Karimi, G. Mollataheri, A. Amini, H. Abdollahi, A. Mirzaeian

"Chah-Palang tungsten deposit is one of the two tungsten indexes in Iran. Based on ore characterization techniques (including optical mineralogy and XRD analysis), quartz, chlorite, atacamite, azurite, malachite, ferberite, illite, goethite and calcite were distinguished as major minerals. The representative sample was analyzed qualitatively by using X-ray fluorescence and chemical assay. Results showed that grade of tungsten oxide and copper were 1.76 and 7%, respectively. Also precious metals such as gold with grade of 1 ppm was reported in the sample. By using the mineralogical studies on the prepared sample, the liberation degree of tungsten minerals in –0.6 mm size fraction was obtained 80%. Several tabling tests were carried out on the original sample which at the optimum conditions and as a result, the grade and recovery of tungsten in concentrate reached to proximately 23 and 59%, respectively. To increase the grade of tungsten in the final concentrate, acidic leaching were performed on the tabling concentrate and its appropriate results indicated that the grade of tungsten increased to 27%. Also more than 90% of copper was extracted as a byproduct in the fallowed process.INTRODUCTIONTungsten, a unique hard, heavy heat-resistant metal, is distributed erratically in economic concentrations throughout most continents, occurring mostly as small irregular deposits that are not readily adaptable to large-scale, low-cost mining methods. The diverse physical characteristics and mineral composition of tungsten ores also present problems in beneficiation, requiring complex hydro- and pyrometallurgical treatment to yield high-purity concentrates suitable for the production of ferro alloys, carbides and super alloys in the steel industry (Hausen, 1989; Kholmogorov & Kononova, 2005). Tungsten is most frequently used as tungsten monocarbide, which has hardness close to diamond, in cemented carbides. The most well-known use of tungsten is in lighting filaments, and other important applications include improving steel properties and use in tungsten alloys, electronics, and chemical products (Hausen, 1989; Kholmogorov & Kononova, 2005)."

Jan 1, 2016

By F. Chiesa, Jeremy Carignan, B. Duchesne, D. Levasseur

"Aluminium A206 (AlCu4) is one of the strongest aluminium casting alloys with tensile properties approaching those of ferritic ductile iron. If the specification on the silicon content (< 0.05%) is easy to achieve during alloy ingot production, it is not the case in a foundry, where returns are used which are not perfectly cleaned from the silicate containing molding sand (Olivine). In alloy A206, the Si content is controlled in order to avoid the formation of a low melting point intermetallic phase (such as phase Q Al5Cu2Si6Mg2); these phases will melt during the solutionizing heat treatment to which alloy A206 must be subjected to develop its outstanding mechanical properties. This incipient melting may deteriorate the mechanical properties of Alloy A206 if the solutionizing treatment is applied at the standard temperature of 530°C.In the present study, a lower temperature solutionizing (520°C) was applied to a high Si content 206 alloy in order to reduce or eliminate the possible incipient melting. This was carried out on a complex shape industrial casting weighing 14 kg (31 lb) and 560x410x250 mm (22x16x10”) in size poured in aluminum 206 with a high silicon content (0.22% vs 0.05% max for alloy A206). Twenty ASTM E8 subsize tensile specimens were excised from two locations in the casting in order to compare the tensile properties for the two solutionizing temperature used (530 and 520°C). Optical and SEM microscopy allowed to investigate the causes of the differences in the properties observed between the 2 zones of the casting studied for 3 different heat treatments. INTRODUCTIONIn spite of their “textbook” outstanding mechanical properties (Up to twice the strength and elongation of the widely used A356 alloy), aluminum-copper alloys of the 2xx series are seldom used because of their propensity for hot tearing [Li, 2011], the segregation of copper [Cho, 2003], and their sensitivity to stress corrosion cracking [Jean, 2009, p. 113)]. Also, because of their wide freezing range and high thermal conductivity, a wide mushy zone makes feeding difficult, unless strong temperature gradients are created by liberal use of chills and risers in the critical zones of the part. Because they are prone to hot tearing, grain refining of Al-Cu alloys is particularly important, titanium playing a major role in the process [Sigworth, 2003]; grain refining has also been shown to be beneficial to fatigue strength [Jean, 2009, p. 103]. The practical basis of foundry practices pertaining to these alloys is outlined in an AFS webinar [Weiss, 2014]."

Jan 1, 2016

By Tim Martin, Dave Tahija

"In April, 2014, Hecla's Greens Creek mill, near Juneau, Alaska, switched from sulphuric acid to the use of dissolved carbon dioxide for lead flotation circuit pH control. The Greens Creek mine uses paste backfill, in which mill tailings are mixed with cement and used to fill mined areas. Some backfill inevitably becomes part of mill feed during subsequent mining cycles, resulting in high feed pH levels and increased dissolved calcium in the lead flotation circuit. Sulphuric acid is traditionally used to lower pH in such cases but it produces undesirable side effects, including poorer lead-zinc separation and unstable froth. The amount of sulphuric acid used at Greens Creek was limited due to these effects, resulting in higher than target pHs when feed backfill content was high. Dissolved carbon dioxide can be added without these limitations so pH levels have been under much better control since the switch. Additionally, lead-zinc separation and froth characteristics have significantly improved.IntroductionThe Greens Creek Mine, owned by Hecla Greens Creek Mining is an underground mine located on Admiralty Island near Juneau, Alaska, producing silver, gold, lead and zinc in the form of lead and zinc flotation concentrates and a gravity gold concentrate (McDonald, Morgen & Hancock, 2012). The lead and zinc concentrates are produced in conventional flotation circuits preceded by a graphite removal flotation step.The underground mine utilizes cemented paste backfill, of which a certain amount is inevitably re-mined in later mining cycles and returned to the mill, mixed with fresh ore. The Portland cement used in the paste backfill is highly basic so that, from the point of view of the mill, the net effect is to introduce a good deal of lime to run-of-mine mill feed, producing a very high natural pH. This high pH needs to be lowered to obtain good metallurgical results."

Jan 1, 2016

By Georges Houlachi, Akram Alfantazi, Michael Mahon, Maysam Mohammadi

Corrosion resistance of the lead-based anodes directly influences the purity of the final product in the zinc electrowinning process. The anodic MnO2 layer that is electrodeposited on the anodes during this process can protect the anodes against corrosion. Sand-blasted anodes generate a uniform, adherent and shiny MnO2 layer, which gradually blisters and eventually sloughs off after several weeks. In this study, we attempted to develop a new method to stabilize the MnO2 protective layer on the anodes during the electrowinning process by providing suitable nucleation sites for electrodeposition of this layer. MnO2 particles (P80=40µm) were used as seed material for this purpose. Different techniques of galvanostatic and cyclic voltammetry polarizations, scanning electron microscopy (SEM) and atomic absorption spectroscopy (AAS) were employed to investigate the performances of the MnO2-seeded lead anodes. The experimental results showed that growth of the MnO2 layer is influenced by the MnO2 seed particles on the anode surface. The MnO2 layers electrodeposited on the MnO2-seeded lead anodes were uniform and strongly adherent to the substrate. This layer was more stable than those formed on the PbAg anode without MnO2 seeding. This could provide the anode with a higher level of corrosion protection. Moreover, formation of undesirable MnO2 mud in the electrolyte and the rate of manganese consumption were decreased when the MnO2-seeded lead anodes were polarized. These observations could be attributed to the different properties of the electrodeposited MnO2 layer on this anode in comparison with that formed on the PbAg anode.

Jan 1, 2016

By T. Gupta, T. Ghosh

"In recent years, the demand for Rare Earth Elements (REE) have grown rapidly due to increasing demand and global supply shortage. The supply deficit of these critical elements has encouraged the search for new sources of REEs, possibly Coal and Coal byproducts. Coals from certain parts of the world can be rich in REEs, and can approach a total concentration of 1000 ppm. Two Alaskan coal samples were investigated for the effect of size and density on the concentration of REEs on three selected size fractions. Flotation tests were conducted for finer fractions. Additionally Bottom ash and Fly Ash samples from a power plant have been examined for REE concentration. The results show that the upgrade potential for REEs on ash basis from whole coal basis ranges from 2:1 to 4:1 for Wishbone Hill and Healy coal samples respectively. Flotation of the finer fraction for both coal samples, conducted under similar conditions, reveal higher concentration of REE’s in the tailings. Both coal samples have a comparatively higher LREE content than HREE. Trends of REE content of the power plant products on ash basis revealed that Fly Ash has a slightly higher concentration of both LREE and HREE than Bottom Ash. Keywords: Rare Earth Elements, Coal, Coal Ash INTRODUCTION Rare Earth Elements (REEs) and their compounds are vital components in industrial, automotive, petrochemical, defense and medical applications. Dysprosium in combination with other elements is used in laser materials and nuclear control applications. Neodymium is present in magnets that are used in green power generation such as the manufacture of wind turbines and also in hybrid cars. Europium, Terbium and Yttrium are used for devices that have visual displays such as computer screens and laptops [1, 2]. REEs pose fewer environmental problems of disposal and recycling than conventional heavy metal counterparts [1]. Rare-earth metals are key ingredients for radar systems, avionics, modern national defense and satellites [2-8]. In the last 25 years China has been mining, processing and refining Rare Earth elements at affordable prices thus gaining a virtual monopoly in the market. The many fold rise of the prices of REE elements over the last few years and frequent disruptions in supply has forced various nations to invest in indigenous extraction of REEs by increasing production from previously productive sites and to expand the production from new alternate sources including coal and coal byproducts [9]. Coal and Coal beds have been found to be significantly enriched with certain critical metals and can be a potential source for both Light Rare Earth Elements (LREE) and Heavy Rare Earth Elements (HREE) [10]. Moreover, coals with high REE concentrations have been discovered in Pavlovka and Rakovka coal deposits in Russia, Appalachian deposits in USA, Sichuan Basin deposits in China and others across the globe [10-13]. A recent study from China looked at how different trace elements (including numerous REEs) partition in various size fractions of Antaibao coal from China. The finding indicates that the REEs, phosphorous, and thorium all have their high concentrations in the particle sizes 0.5 to 3 mm, and 6 to 25 mm. REEs are also often present in the form of phosphates such as monazite in coal [13, 14]. The objective of the study is to identify the concentration of REEs in Alaskan coals and to investigate the effect of density and size in the distribution of REEs in coal and coal byproducts."

Jan 1, 2016