Search Documents

By Rolf Andreas Lauten, Guy Kluck

"Formation of scales may have important detrimental effects in many mineral processing applications. A well-known problem is the need for frequent maintenance to remove scale from processing equipment. Another challenge may relate to encapsulation of valuable minerals in precipitating scale. In this work, we explore the ability of some crystal growth inhibitors to prevent or lower the degree of scale precipitation. In many situations pregnant leach solutions contains substantial concentrations of calcium, magnesium, sulfate and carbonate in addition to dissolved valuable elements, e.g. gold, copper, zinc. Together with non-dissolved gangue minerals, some slurries may also contain particulate gold, copper etc. During normal processing of the pregnant leach solution it may be exposed to temperature gradients or similar promoting precipitation of various scales. Valuable minerals may become entrapped in precipitates and thus become inaccessible to the lixiviant. Use of a crystal growth inhibitor may lower the degree of encapsulation of valuable elements.Using a simple model system, supersaturated with respect to gypsum, the effect of some crystal growth inhibitors on the prevention of scale is evaluated in terms of amount precipitated gypsum, the particle size of the precipitated gypsum and the carbon gold loading capacity.INTRODUCTIONGold bearing sulfide ores are often roasted or pressure oxidised prior to leaching. The purpose of this unit operation is to prevent loading the leaching circuit with sulfides that consume cyanide. Pressure oxidation or roasting chemically converts the sulfides into sulfates and at the same time, the pH of the slurry ends up in the acidic range. Typically, lime addition is the preferred means to raise the pH to around 10 where gold leaching takes place. Combination of large amounts of calcium ions from the lime with sulfate ions from the ore induces precipitation of gypsum. Compounds like calcium carbonate may also precipitate if carbonate ions are present in the slurry. Depending upon the composition of the ore, compounds like calcium carbonate and other types of scale may also precipitate on gold surfaces on the slurry particles. A layer of scale on top of exposed gold surfaces will prevent dissolution in the cyanidation that takes place during leaching. Naturally, such a precipitation may lower the gold recovery."

Jan 1, 2016

By Michael Gauna, Christopher Mark

"For decades, pillar recovery accounted for a quarter of all roof fall fatalities in underground coal mines. Studies showed that a miner on a pillar recovery section was at least three times more likely to be killed by a roof fall than other coal miners. Since 2007, however, there has been just one fatal roof fall on a pillar line. This paper describes the process that resulted in this historic achievement. It covers both the key research findings and the ways in which those insights, beginning in the early 2000s, were implemented in mining practice.One key finding was that safe pillar recovery requires both global and local stability. Global stability is addressed primarily through proper pillar design, and became a major focus after the 2007 Crandall Canyon mine disaster. But the most significant improvements resulted from detailed studies that showed that local stability, defined as roof control in the immediate work area, could be achieved with three interventions:• Leaving an engineered final stump, rather than extracting the entire pillar;• Enhancing roof bolt support, particularly in intersections, and• Increasing the use of Mobile Roof Supports (MRS)A final component was an emphasis on better management of pillar recovery operations. This included a focus on worker positioning, as well as on the pillar and lift sequences, MRS operations, and hazard identification. As retreat mines have incorporated these elements into their Roof Control Plans, it has become clear that pillar recovery is not ""inherently unsafe.""The paper concludes with a discussion of the challenges that remain, including the problems of rib falls and coal bursts.INTRODUCTIONPillar recovery has always been an integral part of underground coal mining in the US. When room-and-pillar methods are employed, large blocks of coal in the form of pillars are initially left in place to support the weight of the overburden. Unless these pillars are subsequently recovered, the coal they contain will never be mined."

Jan 1, 2016

By A. R. Barnes, N. O. Lotter

Recoverable economic copper sulphide minerals such as chalcopyrite, bornite, chalcocite and covellite often occur together in varying proportions in the major copper-bearing ores, and have individual flotation requirements and characteristics. Pyrite also occurs in these ores to varying extents as the sulphide gangue, and is problematic because of its natural tendency to float quickly and easily. In a bulk sulphide float, selectivity against pyrite is desirable, particularly if it does not host other paymetals such as gold or silver. At the same time it is a requirement to float all of the copper sulphides despite their electrochemical differences. The electrochemistry and semiconductor properties of these minerals are reviewed, together with implications for flotation with and without collector addition. Mixed collector systems for the improved flotation of these sulphides are proposed as a solution. The use of xanthate and dithiophosphate in the collector suite allows the co-existence of dixanthogen and free dithiophosphate radical because the latter has a higher redox potential requirement than xanthate to oxidise to the dithiolate. Because some of these minerals require dixanthogen, and others, free thiolate, to generate surface hydrophobicity, a bulk flotation of all the species becomes possible in the overlapping area of Eh and pH between the two dithiolate equilibrium lines on the Pourbaix diagram. The arsenic-signature copper minerals are added to the study, since many copper operations encounter arsenic as a penalty element in the saleable concentrate. It is shown that the addition of arsenic to the copper and iron sulphides alters the semiconductor and electrochemistry properties, and in turn, its flotation characteristics. The degree of mineral association and liberation between these minerals can be a complicating factor due to textural associations, and should also be considered in the process as a next step.

Jan 1, 2016

By Ltd. (CYMCO) Technology Center Yunnan Metallurgical Group Co., S. Jian, T. Song, J. D. Miller

"As sulfide zinc ore deposits become exhausted, nonsulfide zinc ore deposits become the other resource for zinc production. However, flotation for zinc recovery from nonsulfide deposits is much more difficult than the flotation of sphalerite from sulfide deposits and may become an option for zinc production only if a suitable processing technology is developed. In this regard, research efforts are being devoted to the flotation of nonsulfide zinc oxide minerals. Some common methods which have been used for the flotation of zinc oxide minerals include sulfidization-flotation, activation, and direct flotation with anionic and cationic collectors. The traditional flotation techniques have low efficiency and difficulty in separation and recovery of the zinc minerals from gangue minerals, for example, smithsonite (ZnCO3) from other carbonate gangue minerals and hemimorphite (Zn4Si2O7 (OH)2·H2O) from silicate gangue minerals. In this study potassium lauryl phosphate was evaluated as a collector for the flotation of nonsulfide zinc minerals. Results from contact angle and microflotation experiments at pH 6–9 show that hemimorphite (Zn4Si2O7 (OH)2·H2O) can be floated from quartz and that smithsonite (ZnCO3) can be floated from calcite. However, when dodecylamine, which is a common collector reported in literature for the flotation of nonsulfide zinc minerals, was used as collector, no significant difference between nonsulfide zinc minerals and gangue minerals was observed at any pH value. Initial evaluation suggests that potassium lauryl phosphate is effective at low concentration and may be a promising collector for zinc oxide mineral flotation.INTRODUCTIONBefore the twentieth century, zinc was mainly produced from nonsulfide ores (Large, 2001; Gilg, Boni, & Cook, 2008). With the development of differential flotation processes in the late 19th century major production switched from nonsulfide zinc sources to sulfide zinc ores (Hitzman, Reynolds, Sangster, Allen, & Carman, 2003; Gilg et al., 2008). However, as it is becoming more difficult to find new sulfide ores, recovery from nonsulfide deposits is being considered. Nonsulfide flotation for zinc recovery is much more difficult than the flotation recovery of sphalerite from sulfide deposits and may become an option for zinc production if a suitable technology is developed. Zinc and lead oxide ores are difficult to beneficiate ores due to their similar floatability with gangue, high solubility in water, and the influence of slimes (Fa, Miller, Tao, & Li, 2005). In order to improve the performance of oxidized minerals, lots of effort is being devoted to this field of study (Ejtemaei & Mahdi, 2014)."

Jan 1, 2016

By Jason Palmer

"Water in mining is the commodity that has driven the mining industry for decades. Often used frivolously, modern economic and social pressures are forcing change to use less water and to improve the quality of water and effluents. Used in many processes, water is ultimately consumed in tailings disposal and technologies which can increase the recovery of water are constantly being developed. Filtration and thickening are often seen as competing technologies for water recovery however new cases are developing that show significant advantages can be achieved by combining the two technologies to develop the most effective solution. Supported by case studies this paper investigates the merits of each of the technologies and which strategies of combining the two produce the best outcomes.INTRODUCTIONMineral processing applications generally require water for the processing of ores, whether utilising physical or chemical methods. Water is first added in the milling stage and additional water added as required throughout the circuit. Water losses from the circuit are principally associated with the tailings stream. Optimised water recovery is necessary both because it is a scarce commodity and to minimise the environmental impact.Water recovery is usually accomplished through a sedimentation or filtration processes. Water can be removed from the tailings impoundment by evaporation but this does not improve the mine’s water consumption. The water recovery methodology also determines the water quality; increasing water recovery concentrates solutes in the process water and may create recirculating loads of fine solids."

Jan 1, 2016

By Aliakbar Golshani, Behnam Eslami

"Surface settlement adjacent to sensitive structures is a challenging issue in the tunnel engineering. In this study, 3D simulation of TBM excavation has been performed with the FLAC3D code and then the results compared with real monitoring data. Sensitivity analysis was carried out for all parameters affecting the surface settlement, such as the tail void grouting pressure (Pt), the face pressure (Pf), the tunnel diameter (D), overburden (q), shield thickness (t) and the length of the shield (L). The results show that the face pressure, tail void grouting and tunnel diameter have a considerable effect on the maximum ground displacement.In this paper, the monitoring data from Mashhad Metro was used to verify the numerical simulation. Data monitoring for about 47 sections between A2 and D2 stations was selected and a multiple regression analysis was performed. Based on this analysis, an empirical relationship was obtained for the coefficient of regression relationship which confirmed the sensitivity analysis.INTRODUCTIONThe surface settlement due to tunnel excavation is a complex issue, since the surface displacement is a function of several parameters that they are related to the excavation method, soil characteristics and TBM elements. Prediction of deformation is a very important issue, especially in urban areas, since these displacements may be affected the superficial structures. In recent studies, one of the most popular empirical relationships that is used to predict the surface displacement has gussian curve that it was suggested by Peck [1, 2]. An analytical relationship was proposed by Chow that its base assume was isotropic of soil, that surface settlement can be estimated based on the tunnel geometry and the shear modulus(G) [3]. Besides these methods numerical approaches such as the Finite Element Method (FEM) and the Finite Difference Method (FDM) have been used over the last twenty years, since numerical modeling has a high capability to simulation a complex soil conditions and irregular geometry [4]. In this study, all aspects of the EPB-TBM on Mashad Metro Line 2 were modeled and the most important influences on surface displacement in urban areas were determined [1, 3]."

Jan 1, 2016

By A. P. Yovanovic, P. Bonadia, M. N. Moraes, C. F. Matos

"The magnesite flotation operation of Magnesita Refractories, in Brumado – Brazil, has four parallel ball mills working in closed circuit with hydrocyclones to grind the ore for the reverse flotation of silicates in mechanical cells. The modification proposed here opens the circuit for three of the ball mills so that their products are collected together to feed a high frequency screen. The oversize of the screen feeds the fourth ball mill in closed circuit for secondary comminution. The product reports to dewatering and flotation. The undersize undergoes desliming and subsequent flotation operation. According to pilot tests performed, the modification on the magnesite flotation operation will promote a 20% increase in the productivity, 8.5% increase in mass recovery and a 26% reduction in water consumption. The gains are due to the fact that the silicates in the feed are concentrated in the smaller particles (<100µm) with over grinding in the existing closed comminution circuit, making it impossible to take advantage of this natural selectivity. The combination of open circuit, more selective milling, and the high frequency screen, ensures high efficiency particle size classification. This renders the process more effective, both to the screen undersize with its high contents of silicates and fines, and to the screen oversize, which is almost without fines and has a higher magnesite grade. This situation allows for the setting of specific parameters for the flotation of both the primary milling undersize and the secondary milling product.INTRODUCTIONMagnesita Refractories, with its operations site in Brumado, is the largest producer of high purity dead burned magnesia (DBM) in Latin America. The magnesite ore is extracted from an open pit mine, named Pomba, after which it is crushed and handpicked. Due to the presence of disseminated silicate the ore has to be ground and concentrated by means of reverse flotation, before feeding the high temperature kilns for sintering and conversion to DBM.The magnesite flotation unit has an impact crusher to reduce the size of the feeding ore, which is transported to the mills by conveyor belts. The milling operation is composed of four ball mills in closed circuit with hydrocyclones. The closed circuit generates a high circulating load with excess fines, which is detrimental to the selectivity of the desliming and flotation operations, reducing both mass andmetallurgical recovery.In the current scenario, the capacity of the flotation plant is insufficient to meet the demand of the DBM kilns, forcing the operation to work with high purity ores in order to attain the highest possible mass recovery in the concentration process. This is not an ideal situation as it requires the mining site to work with higher stripping ratios.The objective of this work was to improve the magnesite flotation unity to increase its productivity. After a detailed analysis, the milling was identified as the limiting process, which made the authors to focus on this operation."

Jan 1, 2016

By J. Noll, A. Miller, J. Volkwein, C. Pritchard

Hecla Limited, Magee Scientific, and NIOSH have combined efforts to evaluate an in-situ air filtration system for use in an underground mine environment. The purpose of the collaboration was to determine the efficacy of such a technology for reducing the concentration of airborne diesel particulate matter (DPM), with the aim of improving air quality in underground hardrock mines. A secondary goal was to evaluate the use of an Aethalometer as a means of real-time measurement of black carbon as a surrogate for DPM. The evaluation included measuring the DPM-capture efficiency of the filter when it was pre-loaded with dust. Toward this end, rock dust was introduced at the filter inlet to create a dust layer on the filter surface, with the intent of providing improved capture of the much smaller DPM particles. The filtration efficiency for DPM was assessed by comparing measurements of DPM taken at the inlet and outlet of the system, using both real-time and time-weighted-average approaches. The real-time measurements were performed with the model AE33 Aethalometer® made by Magee Scientific. The results of the NIOSH 5040 method analysis were used to assess the effects of the system on time-weighted-average concentrations of total carbon. Results showed a reduction in DPM concentrations in the range of 82%-89%. While the calculated efficiencies based on the two different measurement methods were similar, the DPM levels reported by the Aethalometer were higher, possibly due to differences in the performance of the size-selectors used for the two methods (impactors versus cyclones). More research is required to develop a robust correlation between the two methods, to support the use of the Aethalometer for future mining applications. The advantage of the Aethalometer is that it can measure and record DPM levels for weeks at a time, and can be directly connected to a mine monitoring system, potentially at multiple locations. Ideally such data can be used to initiate the startup of the filtration system should DPM concentrations reach an action level. This work demonstrated that in-situ filtration systems, modified to collect DPM and coupled with real-time monitoring, show promise at reducing DPM concentrations in the mine environment.

Jan 1, 2016

By Z. Bibak, S. Banisi, A. Ghasemi, E. Nematollahi

"The major importance of liners in grinding is their role in providing an appropriate trajectory for the charge. Since it is not possible to study the charge movement by direct observation in operating industrial mills, this task is accomplished by physical (laboratory), and/or, mathematical (software) methods. Because of the high cost and a longer time required for a physical analysis, mathematical simulations have become more common. Simulation of the effect of liner shape on the charge movement has provided a means to select a proper design based on the operational objectives and conditions. Furthermore, the liner shape changes due to wear and impact during operation, which will influence the charge trajectory. This adds more of an incentive to use simulation. These changes in liner could be predicted through liner profile measurements during operation and/or simulation. In this research, an inhouse developed DEM software called KMPCDEM © was used to simulate the charge movement in industrial plant SAG mills. A geometrical method of implementing the shell liners on SAG mills at the Sarcheshmeh (9.75×4.87 m) and the Gole-E-Ghohar (9×2.05 m) operations facilitated the software simulation. Point by point implementation of the measurements of liner profiles of these mills enabled the study to trend the change in the charge movement as the liners wear. Comparison of the simulation to a laboratory mill (1 m diameter) showed that the difference between the measured and predicted charge impact point, shoulder angle and toe angle were 6, 4 and 3°, respectively. INTRODUCTIONComminution is the most energy intensive operation constituting the major portion of operating and capital costs of a mineral processing plant. In the last decade, a vast number of research was aimed at studying various aspects of grinding with the aim of performance improvements (Davis, 1919; Mishra & Rajamani, 1990; kalala, Breetzke, & Moys, 2008). Mill liners transfer the input power to the charge and play a significant role in affecting the motion of the charge (Mclvor, 1983; Mishra & Rajamani, 1990; Radziszewski, 1997; Van Nierop, Glover, Hinde, & Moys, 2001; kalala et al., 2008). Lifters are usually used with mill liners to extend their life and to enhance the grinding and impact breakage efficiency. Mill lifters are used to raise the grinding media and ore to transfer the energy from the mill to the load (Rezaeizadeh, Fooladi, Powell, & Weerasekara, 2010)."

Jan 1, 2016

By John R. Goode

"This paper reviews options for the separation of a mixture of rare earth elements (REE) into its component elements. Earlier separations used selective chemistry such as double salt precipitation and reductive/oxidative processes – methods that still have a place in the industry. Fractional crystallization was developed for more complete separations of adjacent REE. The latter method was replaced by ion exchange (IX), which was in turn replaced by solvent extraction (SX). Two main SX chemistries are in use, solvation and cation exchangers, with several variants (mixed solvents, ionic liquids, etc.) now under investigation. SX plant configurations have evolved including advanced techniques like “hyperlinking”, novel saponification methods, and alternative stripping techniques. The classic mixer-settler is the most commonly employed device although centrifugal contactors have been pilot-tested. Non-dispersive SX options including microfluidic devices and membrane-assisted SX techniques are being developed and could revolutionize the SX option. Other REE separation techniques now being studied include Molecular Recognition Technology (MRT), Free Flow Electrophoresis (FFE), newer IX systems, and electrolytic processes. Additionally, the classical crystallization and selective precipitation methods and newer bacteria-mediated processes, chloride volatilization, high performance liquid chromatography, and magnetic separation systems have been studied. This paper reviews the options and concludes that conventional SX is the technology of choice but viable alternatives could be demonstrated and acceptable within a couple of years.INTRODUCTIONThe chemical properties of the individual REE are very similar which is why REE minerals and ore deposits almost invariably contain a mixture of all fifteen REE, i.e., La to Lu plus Y. That said, the distribution of REE in a given deposit is frequently dominated by the light REE (LREE, i.e., La to Nd). Examples include the Bayan Obo, Mianning, Lynas Mt. Weld, and Molycorp Mountain Pass deposits where heavy REE (HREE – Sm to Lu and Y) typically account for well under 5% of the REE content. The LREE operations produce some HREE but the main sources of these important elements are the ionic clay deposits of Southern China. Importantly, all of the REE recovery operations referenced above, except for cerianite-bearing ionic clay deposits, initially produce a mixed REE precipitate or calcine with a REE distribution similar to that in the ore (Goode, 2016). However, the consumers of the REE, the manufacturers of magnets, phosphors, catalysts, optical glass, etc., require separated products with purities generally ranging from 99% to as high as 99.9999% depending on the element in question and the end use. Hence there is a need to separate the individual REE one from the other. This paper is intended to review the options."

Jan 1, 2016

By Gabriel Zarate

"Los Bronces had two ROM dump leach operations designated Leach I and Leach II. Leach I was commissioned in 1998 and stopped in 2014 due to the mine requirements. Leach II plant, commissioned in early 2002, was built to treat around 700 million tons of marginal ROM ore averaging 0.45 % total copper. The mineralogy of this material was estimated to be 70% chalcopyrite, 20% chalcocite/covellite and the balance oxides.The original electrowinning plant design capacity for copper production was nominal 19,500 tonnes per year at a current density of 276 A/m2 and a current efficiency of 92%. Presently, Los Bronces San Francisco plant typically operates at current densities between 390 and 440 A/m2, much higher than the average in the industry, with current efficiencies around 93% and a maximum copper cathodes production of 37,200 tonnes per year.In order to accomplish these achievements, a number of modifications in the process conditions, in the cell hardware and in the operational procedures have been implemented. In the first case, the specific flowrate, copper concentration and temperature of the electrolyte were modified to accommodate the operational requirements facilitating the increased current density. Associated with the cell hardware, a six cells expansion was added, upgraded equipotential inner cell busbars were installed and the cross section of the cathode hanger bars was enlarged for increased current carrying capacity. Documented operational procedures like short circuit detection and cathode weight control were improved.The modifications implemented and the results obtained are discussed in this paper.INTRODUCTIONLos Bronces Division of Anglo American Chile is located up in the Andes Mountains, northeast of Santiago. It had two cathode plants, Los Bronces at an altitude of 3500 meters above sea level (m.a.s.l.) commissioned in 1998 and closed in 2014 and San Francisco at an altitude of 2800 m.a.s.l. and in operation since 2002.The process is leaching run off mine (ROM) low grade copper sulphide ore in dumps. The mineralogy of this material was estimated to be 70% chalcopyrite, 20% chalcocite/covellite and the balance oxides. The average grade is 0.45% total copper (Cut).At Los Bronces dump, Leach I plant, the pregnant leach solution (PLS) was collected and stored in an underground reservoir. From there, it was fed to a solvent extraction plant with a series-parallel configuration in two extraction stages and one stripping stage. The electrolyte produced was fed to the electrowinning plant having 30 cells and 60 cathodes per cell. Maximum capacity of this plant was 12,000 tonnes per year (tpy)."

Jan 1, 2016

By Chengguo Zhang, Bruce Hebblewhite, Faham Tahmasebinia, lsmet Canbulat

"Coal burst is a dynamic release of energy within the rock (or coal) mass leading to high velocity expulsion of the broken/ failed material into mine openings. This phenomenon has been recognised as one of the most catastrophic failures associated with the coal mining industry, which can often lead to injuries and fatalities of miners as well as significant production losses. This paper aims to examine the mechanisms contributing to coal burst occurrence, with an emphasis on the energy release concept. In this study, a numerical modelling study has been conducted to evaluate the roles and contributions of difference energy components. The energy analysis presented in this paper can help to improve the understanding of energy release mechanisms especially under Australian conditions.INTRODUCTIONCoal burst is one of the most hazardous problems encountered in underground coal mines, which occurs at different locations in a variety of mining systems and operations. This phenomenon always involves a violent and dynamic energy release with large rock mass/coal deformation and ejection that can cause severe damage to openings, equipments and may result in fatalities and injuries.The first coal burst occurrence was reported in Britain in 1738 (Dou 2001). Since then, international experiences are available in Canada, South Africa, USA, former Soviet Union, China, India, France, Germany, Poland and Czechoslovakia. Rice (1935) classified coal bursts as two general types, namely excessive pressure bumps and shock bumps and he further mentioned that pressure bumps are caused when pillar stress exceeds bearing strength. Shock bumps are induced by the breaking of thick, massive strata at a considerable distance above the coal-bed, causing the immediate roof to transmit a shock wave to the coal."

Jan 1, 2016

By Henk Dijkman, Wageningen University, Paula Gonzalez Contreras, Irene Sánchez-Andrea, Jan Weijma, Silvia Vega

"More than 20 years ago, Paques B.V. introduced innovative biotechnologies to recover metals and to remove sulfate from aqueous streams. These technologies find their origin in the exploration of microorganisms involved in the global sulfur cycle. Currently, several sulfur cycle biotechnologies are applied successfully at full-scale. The sulfur cycle is closely linked with the iron cycle, and also the latter offers opportunities for application of innovative biotechnology for the mining industry. Microorganisms of the natural iron cycle carry out reactions that are not feasible by chemical methods such as ferrous iron oxidation with oxygen at pH below 4. Iron oxidation with oxygen can be conducted using microorganisms living at pH between 0.5 and 7 and at temperatures between 0 and 95ºC. Remarkably these microorganisms can also carry out arsenite oxidation at similar acidic conditions and high temperatures. Making use of the extreme features of these microorganisms, Paques and Wageningen University have developed a biological process to precipitate arsenic as scorodite. This biological formation of scorodite is a novel combination of biological oxidation and biocrystallization. Depending on the level of saturation, biological oxidation rates and operational conditions, we could control the formation of the iron precipitates such as jarosite and scorodite. Currently new microorganisms have been harvested from hot springs and rock acid mine drainage to foster the growth of specialized microbial communities with potential high iron and arsenic oxidation capacities and higher resistance to other metals. In our paper we address the ongoing research and development of the bioscorodite process.THE USE OF IRON TO REMOVE ARSENIC In 2015 several environmental disasters related to the release of mine wastewater and tailings occurred. On August 5th, a waste water spill occurred from the Gold King Mine near Silverton, Colorado. A dam holding the tailing pond was damaged and spilled three million US gallons (11 ML) of mine wastewater and tailings, including elements such as cadmium, lead and arsenic, into Cement Creek, a tributary of the Animas River in Colorado. “At their peak, arsenic levels were 300 times the normal level and lead was 3,500 times the normal level” (The Guardian, 2015). In early November, another collapse of a mining dam in the Brazilian state of Minas Gerais spilled between ten and sixteen thousand US gallons of water and sediment after a dam failed from an iron ore mine. Arsenic and mercury polluted the Doce River, arsenic levels were found more than ten times above the legal limit in some places of the river (The Guardian, 2015). Waste production is inevitable during Mining. However, a preventive waste management strategy could have minimised waste production, maximised waste reuse and classified waste by their hazardous degree."

Jan 1, 2016

By S. K. Mitterecker, T. Hofbauer, F. Baerhold

"Acid regeneration is a very important process step in each acid leach circuit. It is required to recover dissolved metals and HCl from spent leaching acid. Andritz Metals presents its recently commissioned spray roast pilot plant. The facility is now available for testing and demonstrating acid recovery or metal oxide production which is a requirement in several flow sheets under development for the mining and specialized oxides industries. Results from pilot test campaigns are reported here. We are currently focusing on a nickel ore leaching process, which requires both a feasible iron control and acid regeneration step. In addition, we disclose the results of a magnesium ore and aluminium recycling test campaign conducted in our pilot plant facility.INTRODUCTION Hydrochloric acid regeneration is widely used in the steel industry to regenerate spent pickle liquors into hydrochloric acid at a typical concentration of 18 wt.%. Andritz Metals (formerly known as Ruthner) has built more than 200 acid regeneration plants worldwide (Andritz Metals brochure). As technology leaders Andritz also has vast experience with specialty metal oxide plants, producing metal oxides such as aluminium oxide (Al2O3), magnesium oxide (MgO), nickel oxide (NiO), cobalt oxide (Co3O4) and mixed oxides from metal chloride solutions (Baerhold F., Lebl A., Starcevic J., 2006), (Jedlicka, H., n.d.), (Ruthner M.J., Krischner H., 1973), (Ruthner Ind. Planungs AG, 1967). Hydrochloric acid leach circuits have been developed and proven in the industry for many years. Examples of industrial applications are: synthetic rutile production (TiO2) (Walpole E.A., Winter J.D., 2002), Quebec Iron and Titanium’s UGS process (Patoine M.-C., De Mori A., Borowiec K., Coscia C., 2002), magnesium and potassium production (Priemer H., 1973) and Goro Nickel (Vahed A., Colton D.F., Duterque J.P., Karner W., Baerhold F., 2004), (Taylor A., 2013). One of the critical process steps in developing a hydrometallurgical process is acid regeneration, as it is an economic requirement to recover both the dissolved metals and acid (commonly HCl) from the spent leaching solution."

Jan 1, 2016

By B. McFadzean, J. Taguta

In order to recover minerals by flotation, the sub-processes of collector adsorption onto the valuable minerals followed by bubble-particle attachment should occur efficiently. This paper investigates both of these sub-processes for various thiol collectors and their mixtures onto base metal sulfide minerals. The aim of the work was to investigate whether there is a correlation between the strength of the collector interaction with the mineral and the subsequent bubble-particle attachment. The collector-mineral affinity was measured experimentally using an isothermal titration calorimeter in order to determine the molar enthalpy of adsorption for each collector-mineral system. The bubble-particle attachment was measured using a microflotation device which essentially determines the hydrophobicity of the mineral. Sodium ethyl xanthate (SEX) and sodium diethyl dithiocarbamate (DTC) and mixtures thereof were used as collectors with either single minerals or binary mixtures of pyrite and chalcopyrite, respectively. The adsorption enthalpies of the collectors were interpreted with reference to the chemical structure of the collector molecule and showed that the greater the positive inductive effect of the collector, which may be qualitatively related to their pKa, the greater their affinity for the mineral surface. In the microflotation studies, recoveries were strongly related to the alkyl chain length but there was no correlation between the enthalpies of adsorption and the flotation recoveries. When mixtures of collectors were used there was clear evidence of synergistic effects and in the case of DTC/xanthate mixtures it is possible that this synergism is related to a DTC promoted oxidation of xanthate to dixanthogen. When mixtures of pyrite and chalcopyrite were used the flotation recovery and enthalpy of adsorption of SEX onto the individual pyrite particles in the mixture increased substantially compared to the case of pyrite alone. Mechanisms are proposed to interpret these important observations.

Jan 1, 2016

By J. F. Fiset, N. Bouzoubaâ, N. Reynier, C. Laviolette, Canadian Nuclear Laboratories

Canadian Nuclear Laboratories (CNL) is developing a disposal strategy for radioactive wastes, which contain significant amounts of uranium, cesium, and mercury. There are safety and economic incentives for the extraction of these elements before permanent storage in deep underground repositories. In addition, the actinide elements are also an important component in rare earth element (REE) ores and considered as impurities. Actinides separation from REE tailings is a significant concern in order to manage radioactive nuclides. Reprocessing mine wastes may present significant financial and environmental benefits. Experiments were carried out with radioactive cemented wastes (RCW) prepared at CanmetMINING. For all of the tested RCW batches, solubilisation yields are above 97% for Cs and 98% for U and Hg. Sulphuric acid leaching with potassium iodide improved the solubilisation of Hg by oxidation and formation of the tetraiodide complex (e.g. HgI4 2-, Kf = 2.1030). Cs and Hg were removed selectively by using potassium cobalt hexacyanoferrate (KCFC) and Lewatit TP214 ion-exchange resin respectively. U recovery using the chelating resin Lewatit TP260 was the most efficient. The presence of high iodine concentration improved the U uptake by the resin. The best U elution was obtained using 1 M Na2CO3, which resulted in 99% U recovery. U was then precipitated as sodium diuranate. A counter current effluent recirculation was performed successfully on RCW. The process was also applied to submerged tailings collected from two U mines and an REE ore. This paper presents an innovative process, using sulphuric acid and potassium iodide, for U, Cs, a

Jan 1, 2016

By L. M. Lowe, D. B. Chambers, D. G. Feasby

"The presence of the naturally occurring radioactive elements uranium and thorium in rare earth (RE) resources can present challenges in achieving regulatory and social acceptance. The discovery and awareness of radioactivity in mineral resources radioactivity typically generates strong public intuitive responses that may be project prohibitive; a significant proportion of such resources contain radioactivity.The objectives of this paper are to demystify the presence of uranium and thorium in RE resources and to demonstrate how a RE project can be safely developed, operated and closed from a radiological perspective. Radioactivity in RE resources is principally thorium-based. Thorium is interesting and challenging from a metallurgical perspective – one of those stubborn metals commonly assessed as refractory. Thorium is difficult to mobilise into solution and easily precipitates out. Thorium is a common element in the earth’s crust – about 10 ppm on average, and natural geophysical systems conclusively demonstrate its immobility. Specific mine tailings contain elevated levels of thorium, but the contained thorium is neither a significant ecological nor a personal hazard.Waste management for a hard rock rare earth project includes the management of mineral processtailings, waste rock, and metallurgical residue. Proven strategies are available for tailings and waste rockfor all climate conditions. The management of the metallurgical residues is potentially more challenging.Example robust strategies for addressing these challenges are presented.A potential way to reduce the radioactivity of rare earth metallurgical wastes is to selectively remove uranium and thorium. Uranium oxide is readily marketable, but its concentration as a byproduct typically triggers extensive regulatory processes. Thorium is presently not marketable, but may be so in the not-too-distant future with the development of thorium-based nuclear energy. The pro’s and con’s of uranium and thorium byproduct recovery are summarized."

Jan 1, 2016

By Nawshad Haque, Leanne Smith, Hal Aral, Joseph Cho, Warren Bruckard

"Water availability is one of the principal parameters in determining the feasibility of mining projects in arid and semi-arid regions. The volumetric water footprint (VWF) of a conceptual model of a copper flotation plant was found to be 2.45 kL/t Cu ore, compared with an actual measurement reported in the literature of 2.72 kL/t Cu ore. The flowsheet considered included mineral processing stages such as crushing, screening, grinding, classification, separation, flotation, thickening and filtration. The effect of a number of variables on the VWF was evaluated, including solid/liquid ratio, feed mass flowrate, ore loss, water loss, moisture content of ore, ore grade and water recycling. The use of seawater with recycling provided the most environmental and economic advantage among several scenarios evaluated. The study assumed a price of $1/kL freshwater, $4/kL for transport over a 200 km distance at 2,000 m altitude and $4/kL for water treatment. The water related cost of the desalinated seawater use scenario was A$493/t Cu concentrate, while the water related costs of fresh water and blended water scenarios were A$308/t and A$268/t Cu concentrate, respectively. The water related cost (fresh water scenario) accounted for 44% to 49% of the entire mining and processing costs that included drilling, blasting, loading, hauling, crushing, grinding and concentrating. The total overall cost was A$435/t Cu concentrate for the seawater with recycling, compared to A$451/t Cu concentrate for the fresh water with recycling case.INTRODUCTIONReducing the water footprint (WFP) by utilising alternative water sources has been a focus of mining projects due to increasing concerns about water scarcity and growing energy costs. The global mining industry can expect to experience fresh water shortages in the future, and saline or hyper-saline water may be the only available water source to process minerals in arid regions. Extensive studies on alternative water sources (e.g. seawater, desalinated seawater, blended water) and the reuse of process water have recently been conducted (Moreno, Aral, Cuevas, Monardes, Adaro, Norgate & Bruckard, 2011; Aral, Mead, Cuevas, Davey & Bruckard, 2010). Such studies provide sustainable and economic strategies for mines and concentrators in the arid or semi-arid regions of the world such as in Chile, Peru, Indonesia, and Portugal. More work, however, is needed to confirm water consumption data for different base metal flowsheets and use this data to develop water models that can lead to reduced WFPs and more sustainable water usage in the mining industry."

Jan 1, 2016

By S. Acar

"In recent years the gold mining industry has been challenged by declining metal prices as well as having to treat ores that have low grades and are refractory in nature. Many factors must be considered when metallurgical studies are designed to develop process design criteria for these type of ores. These factors are mostly related to the mineralogical and chemical compositions of the ores, the geological setting of the deposit and how the ore/waste will be mined, such as whether openpit or underground, the mine schedule, and the mine fleet type and capacity. The purpose of this paper is to provide an experience-based practical approach to how to select and characterize test samples as well as devise process development metallurgical studies for both oxide and refractory gold ores, and to provide insight into some of the matters that might go wrong during the course of the studies. This paper is intended as both a guide for someone new to the field and also as a reminder for those familiar with the field. IntroductionThe recent decline in ore grades and metal prices have challenged mining companies to reduce capital and operating costs associated with developing new mineral resources. In some cases, metallurgical studies have been sacrificed to prevent cost overruns resulting in inadequate mineralogical, chemical and metallurgical characterization. Consequences have included longer construction schedules, higher initial and working capital, higher operating costs and less than desirable plant performance (Whincup, 2010; Torres, Chaves and Meech, 1999).Mineralogy, geology, mining type and sequence, and the metallurgy of an orebody will determine the process development metallurgical study requirements and eventual process plant design. Therefore, once the geologist has an early indication of a prospective orebody, geologists, metallurgists, mining engineers, and social and environmental responsibility scientists should convene and devise a plan on how to exploit the orebody economically (Lunt, Ritchie and Fleay, 1997).Geologists may find a prospective orebody solely based on grade. However, if the orebody cannot be mined and processed economically, then it is deemed not to be a deposit. An example of this could be a refractory gold deposit, either sulfidic, carbonaceous or siliceous refractory or any combination of those, that may not be mined and processed economically due to reasons such as the physical location of the deposit, depth of the ore lode, or social and environmental concerns. Therefore, an early collaboration between all disciplines must be established.Each orebody may have its own unique mineralogical, geological and chemical characteristics (Guresin et al., 2012). These unique characteristics should be effectively sampled to reduce risks associated with process design and engineering efforts for the process development metallurgical studies. If the sample or samples are not representative of these unique characteristics, then the studies performed will be pointless. The project metallurgist in charge of conducting metallurgical studies should also possess general geology, mineralogy and mine engineering knowledge. Recommended readings are a book on understanding mineral deposits by Misra (2000) and articles on heap leach development by Scheffel (2014a and 2014b)."

Jan 1, 2016

By L. Hutton, S. W. Colley

"The release of soluble salts of base metals from acid mine pits and in the waste water from metal refiners is an avoidable source local pollution and contamination. Tightening of the regulations controlling natural resource extraction and industrial wastewater discharge is mandating the removal and recovery of metals from waste streams, and the remediation of contaminated sites. There is an economic incentive in recovering the valuable copper and nickel, as the value of the recovered metal can offset remediation costs and for high flow waste streams can be a source of income. Extraction of metals from waste streams by conventional Ion Exchange and chelation resins is widely practised, but has limitations on applicability in complex and dilute feeds due to the structure and properties of polymeric resin beads. Composite Advanced Ion Exchange (AIX) materials have been developed for the recovery and purification of base metals from base metal mining and metal processing industries. A silica-composite based resin has been developed for the selective extraction of copper from high iron containing feeds. This resin can be eluted with sulfuric acid yielding a copper stream suitable for return to solvent extraction or to electrowinning. We describe the development and application of the resin and process to two acid mine drain feeds of varying copper and iron concentrations, and show that the copper concentration can be considerably upgraded even at small scale with a final metal content of >95% copper.INTRODUCTIONWaste water with high sulphate concentrations, low pH and containing complex and variable mixtures of metals is an inevitable product in the mining, extraction and metal refining industries. One problematical water source is Acid Mine Drainage (AMD) which in addition to the metals of interest also contains a wide range of contaminating elements. Purge streams from metal refining are less complex in composition but contain significant quantities of the value metals. The typical treatment of such waste streams is treatment with lime to increase the pH of the water, precipitating the dissolved metals and sulphate as a sludge of mixed metal oxides/hydroxides and sulphates. The process is effective in producing a water stream that can be safely discharged but if there are significant concentrations of value metals such as copper, nickel, zinc then there can be a considerable loss of metal value."

Jan 1, 2016