Search Documents

By Zhucheng Huang, Ronghai ZHONG, Liangming Wen, Tao Jiang

The reduction roasting-magnetic separation and its strengthening of high silicon coal-containing mini-pellets by sodium additives were researched. The results show that the carbon gasification reaction and reduction of fine hematite in high silicon coal-containing mini-pellets with 3% sodium additives were enhanced. Comparing with no sodium additives, the gasification rate of carbon with 3% sodium additives reacting with CO2 for 40 minutes at 950 and the metallization rate of reduced pellets with 3% sodium additives after roasting for 35 minutes at 960 increased from 35.15% and 58.72% to 86.98% and 86.15%, respectively. The analysis of SEM equipped with EDS demonstrates that the inner pore of reduced pellets with 3% sodium additives was more developed and the iron grains size significantly enlarged, meanwhile, the iron grade of concentrate increased from 60.45% to 80.23% and the iron recovery rate decreased from 84.67% to 80.78% after grinding-magnetic separation.

Jan 1, 2016

By Huimin Lu, Zegao Sun, Zhijiang Gao

The traditional Ti6Al4V alloys were obtained by the smelting reduction of V-Ti bearing beach placer by rotary hearth furnace and aluminothermic reaction in laboratory. First, it gets he lp from combined rotary hearth furnace and grinding magnetic separation process to prepare titanium slag containing vanadium. In this study, a neural network model was used. The comparisons between experiment results and neural network simulation results show that genetic algorithm (GA)-based on back propagation (BP) method can predict the degree of reduction and separation of iron and slag with higher prediction accuracy. Then by aluminothermic reaction process, the optimized process parameters for Ti-V-Al alloys were searched. Al can deoxidize metal V and Ti from the metal oxides of artificial rutile containing vanadium. Finally, traditional Ti6Al4V alloy can be obtained by remelt and adjust the constituents.

Jan 1, 2016

By Pan Gu, Zhen Zhang, Jiang Diao, Bing Xie, Hongyi Li

Furnace refractories are in most cases chemically incompatible with smelter slag, which leads to a steady erosion in their thickness over time. Once too thin, refractory walls become mechanically unstable and catastrophic failure can result. Historically, external shell cooling was applied to generate a freeze lining of slag and thus prevent refractory erosion. Many modern high intensity smelting furnaces instead maintain their physical integrity by the use of internally cooled wall panels, plates or finger coolers. An initial refractory lining is often installed inside of the coolers, such that the furnace originally operates with a temperature (insulated) rather than a heat flux (freeze lined) boundary condition. This paper examines the change in slag-wall heat transfer coefficient and slag superheat as a function of process intensity. The implications of the changes in heat transfer on residual brick thickness are explored using analytical modelling.

Jan 1, 2016

By Tianzu Yang, Weifeng Liu, Lin Chen, Wei Chen, DUCHAO ZHANG, HUI XIAO

Oxygen-rich side blow bath smelting (OSBS) technology was developed in 2000 based on Vanyukov process. This technology exceeds the traditional pyrometallurgical methods by its great processing capability, high metal recovery and environmental-friendly property. In the past 15 years, OSBS technology extended its application area from lead industry to bismuth, antimony and waste recycling industries, etc. This paper introduces the history and new developments of OSBS technology. The typical industrial applications examples of the OSBS technology in China, including high lead slag reduction, low grade bismuth-lead concentrate smelting and metallurgical waste recycling, are reviewed. Especially, the unique furnace properties and technical parameters are compared. Finally, the potential research directions of OSBS technology are summarized.

Jan 1, 2016

By Huanmei Yuan, Yuanyuan Wang, Hao Bai

Composite phase change materials are widely used in energy-saving and energy efficient process. Nano-encapsulated phase change materials are especially significant for making advanced working fluid applicable to waste heat recovery or storage. In this study, silica-coated stearic acid (SA) Nano composite phase change materials were prepared from tetraethyl orthosilicate (TEOS) and stearic acid (SA) via sol-gel process. The materials were investigated by Field emission scanning electron microscopy (FE-SEM), Transmission electron microscope (TEM), Fourier transform infrared spectroscopy(FT-IR) and Differential scanning calorimeter (DSC).The FE-SEM and TEM results show that monodisperse microspheres with stable core– shell structure were formed and SA was encapsulated in the silicon dioxide shell. The FT-IR results show that there were no chemical reaction between silicon dioxide and SA, which is the chemical property of the composite material, is stable. The DSC results show that the composite phase change material has favorable heat capacity.

Jan 1, 2016

By Minting Li, Hailong Yang, ChangWei, Cunxiong Li, Gang Fan, Xingbin Li, ZhiganDeng

The filtration problems on acid leaching sludge of high silicon zinc ore have been paid extensive attention in zinc hydrometallurgy. It was found that soluble silica can be effectively converted into silica precipitate with good settling, filtration and washing properties, and the filtration rate can be in excess of 800 L/m2 · h under certain leaching conditions. According to investigating on the filtration rate, viscosity and concentration of silica of leaching sludge or liquor, the filtering temperature can tremendously improve the filtration property of pulp. At the same time, the experimental data indicated that the viscosity of leaching liquor was the key factor influencing filtration property of leaching sludge.

Jan 1, 2016

By Shengli Wu, Mingyin Kou, Laixin Wang, Zhe Wang, Xinliang Liu

The sticking behavior of iron ores in the shaft furnace is one of the most important problems in the COREX melting progress, which directly influence the smooth operation and productivity of shaft furnace. Therefore, it is of great importance to study the sticking behavior of pellets in COREX shaft furnace. The results showed that porous metallic iron produced at the interface of pellets samples was the main reason for the sticking of pellets in the COREX shaft furnace. The SI (sticking index) and metallization rate increased with the reduction temperature and gas flow, and decreased with melting rate. However, the SI of pellets in the COREX shaft furnace could be decreased by the proper match of melting rate and reduction temperature, reduction temperature and gas flow, while the metallization rate of pellets were kept at a certain level. Furthermore, the matching of melting rate and reduction temperature was more effective than the matching of reduction temperature and gas flow.

Jan 1, 2016

By Z. W. Zhang, Songsong Xu, Jinhui Li, Yun Zou, Yu Zhao

High strength low alloy (HSLA) steels with high strength, high toughness, good corrosion resistance and weldability, can be widely used in shipbuilding, automobile, construction, bridging industry, etc. The microstructure evolution and mechanical properties can be influenced by thermomechanical processing. In this study, themomechanical processing is optimized to control the matrix microstructure and nano-scale precipitates in the matrix simultaneously. It is found that the low-temperature toughness and ductility of the steels are significantly the matrix microstructure during enhancing the strength by introducing the nano-scale precipitates. The effects of alloying elements on the microstructure evolution and nano-scale precipitation are also discussed.

Jan 1, 2016

By Bo Liang, Hongmin Zhu, Kai Huang, Shafiq Alam

A new approach of recovering platinum and palladium from electronic wastes by hydrochloric acid leaching followed by selective adsorption on low-cost and environmentally benign biomass sorbent prepared from easily available agriculture waste is suggested. The obtained adsorbents were prepared by a combination of chemical modification and hydrothermal carbonization process with (NH4)2C2O4. It was found that the maximum adsorption capacity of hydrothermal carbonized garlic peel for Pt( ) and Pd( ) was 1.64 and 0.42 mol/kg respectively. The Langmuir adsorption isotherm was applied to describe the adsorption process. Kinetics of the Pt( ) and Pd( ) ions adsorption was found to follow pseudo-second-order rate equation. The adsorbents were examined by scanning electron microscope (SEM), and Fourier transform infrared spectroscopy (FT-IR). Based on the characterization results, a possible mechanism of Pt( ) and Pd( ) ions adsorption with the hydrothermal carbonized garlic peel was proposed. This study provides a promising adsorbent with efficient adsorption property for platinum and palladium recovery from the leach solution of electronic wastes.

Jan 1, 2016

By Edmundo Manilla, Merete Tangstad, Daniel Davila, Eli Ringdalen

FeMn alloys are typically produced with lumpy ore or sinters. Minara Autlan, the Mexican FeMn producer, is however making Mn-nodules as a raw material for Mn-alloy production. The Mn nodules have been characterized by XRF, XRD, by wet chemical methods and by EPMA. The Mn/Fe ratio is somewhat lower compared to commercial Mn ore on the marked. The basicity of the ore is however close to 1, and additional fluxes may not be used. The Mn-nodules will be in a state of manganosite (MnO), tephroite ((Mn, Ca)2SiO4) and galaxite ((Mn,Mg)Al2O4). This leads to a low melting temperature area. A low porosity and low amount of higher Mn-oxides gives a high thermal strength to the nodules.

Jan 1, 2016

By Y. Wang, L. Liu, G. Xu, Y. Lv J. Sheng H. Zhang

In order to increase the service life of large scale coke dry quenching furnaces, the damage mechanism of lining was investigated, and the structure and properties of lining refractories used in cooling section were researched. The results showed that the abrasive wear volume of lining bricks at one fourth height section under skew tunnel was smaller than other sections. The wear loss of mullite brick and dense clay brick used in the lining of cooling section were respectively 8.02 cm3 and 11.65 cm3 in fifteen minutes. The mullite brick was laid with clay brick alternatively. By the different wear rate, the surface of lining was rough and uneven in the later service life, and short brick was easily dropped from lining. During the service, the basis wore off more easily than the aggregate. It is necessary to improve the wear resistance property, which will increase the service life of cooling section’s lining for coke dry quenching furnaces.

Jan 1, 2016

By Mao Chen, Baojun Zhao, Zhixiang Cui, Leonel Contreras

Viscosity is one of the important physiochemical properties of metallurgical slags which is important for slag tapping, metal loss in slag, freeze lining and fluid dynamics. High temperature viscosity measurements are time- and cost-consuming and the number of experiments is limited. Viscosity model is an effective way to predict the viscosities of the complex slags at high temperature. However, a reliable viscosity model can only be developed on the base of accurate experimental data. A unique high-temperature viscosity measurement apparatus developed at The University of Queensland enabled accurate viscosity data to be measured for the “FeO”-SiO2-CaO-MgO-Al2O3 system in equilibrium with Fe. An accurate viscosity model has been developed based on Eyring’s theory and extensive viscosity measurements. The viscosities of copper smelting, converting and cleaning slags over a wide range of compositions and temperatures can be predicted and applied in the process control.

Jan 1, 2016

By Mehmet Bu daycı, Onuralp Yücel, Ahmet Turan, Murat Alkan

In this study, iron based alloys (Fe, Fe-Cr-Ni-Mo, etc.) were produced by using metallothermic methods starting from Mill Scales obtained continuous casting processes. During the process, the combustion was realized by ignition and the produced wave propagates throughout the reactant mixture yielding the desired product. In this work, Mill scale used as an iron source, which includes +2, +3 values iron oxides. Aluminum, Magnesium and Silicon were used as reductants. In these metallothermic experiments, different ratios of reductants were examined, and their effects on the metal recovery and alloy compositions were investigated. The samples were characterized by using chemical analysis (AAS), XRD and XRF techniques.

Jan 1, 2016

By Mei-le He, Min Chen, Xiang Shen, Lei Xu, Lei Liu, Nan Wang, Xue-liang Yin

In the current study, Al2O3-MgO-CaO refractories were prepared at 1400-1600 by the addition of MnO micro-powders, and the effect of MnO addition on densification behavior of the refractory was discussed. The results showed that the doped MnO dissolved to MgAl2O4 phase, and promoted the growth of MgAl2O4 grains by the formation of MgAl2O4 solid solution. As a result, the dense microstructure was obtained, with the apparent porosity decreased from 19.2% to 5.4% and the bulk density increased from 2.78g/cm3 to 3.15g/cm3 after firing at 1600 for 2h by the addition of 4% MnO. In addition, a texture microstructure was observed, which is considered to be favorable to improve mechanical properties and the service life of Al2O3-MgO-CaO system refractories.

Jan 1, 2016

By Teruhisa HORITA

The durability of SOFCs is one of the critical issues to realize the SOFC systems. In order to improve the durability, a precise degradation mechanism should be clarified at the different functional ceramic interfaces in SOFC cells and stacks. This paper reviews the improvement of SOFC durability by the mass transport analysis especially at cathode/interlayer/electrolyte interfaces. We have made a precise analysis on the reaction of cathode with impurities. Especially at the (La,Sr)(Co,Fe)O3/CeO2/ZrO2 interfaces, a significant amount of SrCrO4 and SrSO4 were observed at the (La,Sr)(Co,Fe)O3 surface as well as inside the (La,Sr)(Co,Fe)O3 cathode, which suggested some process occurred for both poisoning. Possible degradation mechanisms were proposed based on the observation data.

Jan 1, 2016

By Anxiang Wang, Kunhua Wu, Yifu Li, Junjie Xu, Yongnian Dai, Bin Yang, Lingxin Kong

In this study, the saturated vapor pressures of tin (Sn) and antimony (Sb), the separation coefficient and the vapor-liquid phase equilibrium of Sn-Sb alloy were theoretically analyzed, which demonstrate that it is possible to separate Sn and Sb by vacuum distillation. The process parameters of vacuum distillation, including the distillation temperature, distillation time and alloy mass (thickness of raw materials) on the direct yield of Sn and the content of Sn in liquid phase were investigated by using single factor experiments. The preliminary results show that the direct yield and the content of Sn are 98.77 wt.% and 96.01% with the optimized distillation conditions of a distillation temperature of 1473 K, a distillation t ime for 45 min and a Sn-Sb alloy mass of 125 g ( thickness o f 8 mm). The distillation parameters in the study provide effective and convenient conditions on separation of Sn-Sb alloy.

Jan 1, 2016

By Caryn Wendt, Donna Post Guillen, Armando McDonald, Erik R. Coats, Chaston Ellis, Kevin Feris

Dairy operations constitute ~2.5% of annual U.S. greenhouse gas (GHG) emissions, making dairies one of the largest sources of industrial GHG emissions. We are developing a novel, integrated system to achieve a net reduction in dairy GHGs while producing value-added materials and products. This integrated manure-to-commodities system converts dairy manure to bioenergy, sequesters carbon by converting volatile fatty acid-rich fermenter supernatant to bioplastics, and utilizes anaerobic digester (AD) and polyhydroxyalkanoate (PHA) reactor effluents to produce algae that can be harvested and internally recycled to enhance PHA production and sequester carbon. A decision-making tool is being developed for the integrated system that quantifies net GHG reduction, carbon sequestration, nutrient management and economics.

Jan 1, 2016

By Juergen Antrekowitsch, Stephan R. Steinacker

The main aim of the electric furnace treatment in the primary copper industry is the reduction of valuable metals such as zinc, lead or copper itself. On the one hand legal restrictions for the further use of the treated slag are constantly getting stricter while on the other every type of loss in the oxidic phase leads to economic disadvantages. In order to fully understand and to improve the process, kinetics during the reduction play an essential role. In the first part, this paper highlights the theoretical background of the reduction process, while the following chapters present experimental aspects and results from laboratory scale trials at the Montanuniversitaet Leoben. In addition, the comparison between the chemical reaction and the diffusion model plays a continuously important role. By investigating the reducibility of electric furnace slag, process adaptions and ameliorations are developed.

Jan 1, 2016

By Aichun Zhao, Rui Wang, Yihong Li, Yanping Bao, Yafeng Ji, Jiansheng Liu, Xiao Hu, Qingxue Huang

The slag entrapment under different conditions of 80t blowing argon ladle furnace was investigated by physical simulation. The water was used to simulate liquid steel and liquid paraffin was for slag. The processing of slag entrapment under different blowing structures was analyzed and the critical velocity and critical droplets diameter of describing it was obtained. Based on the experiments, the relationship between the interface flow velocity and the critical blowing rate CBR was deduced. In the real process, it is suggested that the bottom blowing rate is from 40 L/min to 180L/min when the interface tension is 0.12~1.2 N/m during the soft argon blowing.

Jan 1, 2016

By Yousef Mohassab, Feng Chen, Hong Yong Sohn, Mohamed Elzohiery

The determination of reduction degree in a DR process is sensitive to the total iron in the ore and DRI. An accurate and high throughput analysis method for total iron has been developed. Titration of the solution after tin(II) chloride reduction of ferric ion is a widely used method for iron analysis. However, it is a multistep method that requires many chemical reagents and much time. In this work, an ICP-OES analysis method with higher or equivalent accuracy compared with the titrimetric method was developed. This method has much higher throughput and demands fewer chemical reagents compared with the titrimetric method. In this paper, a comparison of the two methods is presented.

Jan 1, 2016