Search Documents

The steps for the beneficiation of iron ores differ from ore to ore, depending on the mineralogical phases of the particular iron ore and the nature of the association of the gangue minerals with iron oxide in that ore. The extent to which the beneficiation can be undertaken economically depends both on the amount and the nature of the gangue. The analysis of the phases present in an orebody optimises the mining and process operations (separation, beneficiation, sintering, etc).X-ray diffraction (XRD) provides qualitative and quantitative information about the main ore phases as well as the gangue mineralogy and the amorphous content present in a sample. In addition, modern quantification methods such as Rietveld refinement allow the calculation of the distribution of elements in solid solutions such the substitution of Fe with Al in goethite or hematite.The use of high speed detectors has made XRD an important tool for grade and process control. Finger printing of XRD data can facilitate multi-dimensional mapping of ore deposits and drill cores, identifying regions of favourable mineral compositions. Grade control using XRD can be completely automated and controlled remotely.The two case studies in this paper demonstrate how XRD and finger printing can be used for grade control, process optimisation and quality control of a goethitic and a magnetitic iron ore. The enormous potential of XRD as an inexpensive, reliable tool, useful in the characterisation of iron ores will be demonstrated.CITATION:K÷nig, U, 2013. Application of x-ray diffraction to iron ores - potential implications for grade control and downstream processing, in Proceedings Iron Ore 2013 , pp 275-280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By E Selvapandian, R Barr

Arrium (previously OneSteel) initiated a desktop study into the performance of its hematite ore beneficiation plant in early 2010. The beneficiation plant utilises jig concentrators and spirals to upgrade low-grade hematite recovered during mining at the Iron Duke (ID) mine site located 60 km south-west of Whyalla. The study, conducted in conjunction with Mineral Technologies, identified a number of opportunities for improvement, which were validated by a series of sampling campaigns and a pilot plant trial. One of the major recommendations was to upgrade the ultra-fines processing circuit from a single-stage spiral circuit to a three-stage circuit. The upgrade of the ultra-fines circuit was estimated to provide a significant increase in fines production and grade.In order to capitalise on the strong iron price at the time of the project, Arrium decided to utilise a fast-tracked approach to design, construct and commission the processing equipment required to achieve the improvements identified. This decision introduced the risk of missing critical steps in the project development process, which could have potentially resulted in major issues in latter stages of the project. In addition to the challenges introduced due to the expedited time line for project completion, this project presented unique challenges due to its brownfield nature. One such challenge faced was the integration of the new equipment and control system software.Furthermore, the importance of the ID ore beneficiation plant (OBP) contribution to the companyÆs export commitments meant the upgrade work had to occur while minimising disruption to normal operation. This decision presented a set of new challenges to an already complex project. One such challenge was the need to build and commission the new spiral circuit in isolation from the operating plant.The aim of this paper will be to highlight some of the challenges faced in a complex brownfield project such as the ID OBP upgrade and discuss how they were managed to enable the successful commissioning of the process in early 2012.CITATION:Selvapandian E and Barr, R, 2013. Managing challenges faced in the brownfield commissioning of an ultra-fine hematite processing circuit at ArriumÆs Iron Duke ore beneficiation plant, in Proceedings Iron Ore 2013 , pp 533-538 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By D Porta, E Grigolato, K Behrens

################

Aug 12, 2013

By J Pan, T Chun, D Zhu, Z Guo, J M. Young, T C. Ooi

With the rapid development of the Chinese steel industry, the strong demand for iron ores has led to huge imports of various iron ores from all over the world. As a relatively new force in the iron ore world and an important raw material supplier, Fortescue Metals Group (FMG) has achieved an annualised production rate of 100 Mt of iron ore fines. Typical blends were designed to simulate sinter blends employed in Chinese steel mills, and to determine sintering properties and metallurgical performance of blends comprising FMG Rocket fines in pilot sinter pot. It is shown that the sinter of typical blends comprising 15 - 20 per cent rocket fines possesses excellent sintering properties and metallurgical performance. With Rocket fines substitution for competitor ores in a typical customer mill blend comprising fully imported fines, the sinter productivity and tumble index increased from 1.45 t/m2h and 62.0 per cent to 1.54 t/m2h and 64.0 per cent, respectively, while attaining similar reducibility index and reduction degradation index at lower solid fuel consumption.CITATION:Zhu, D, Guo, Z, Ooi, T C, Chun, T, Pan, J and Young, J M, 2013. Sintering and metallurgical performance of blends comprising Fortescue Metals Group rocket fines, in Proceedings Iron Ore 2013 , pp 519-524 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By J M. F Clout

The low-grade clay-rich -1.0 mm fraction of fine iron ores have often proved difficult to upgrade and capital intensive to process when using traditional wet beneficiation technology including single or two stage hydrocyclone desliming, wet high intensity magnetic separation (WHIMS), spirals and final dewatering using fine screens. Very fine (<0.010 mm) clay-rich slimes simply follow the water split to the hydrocyclone underflow where it often impedes the subsequent processing performance of any downstream spirals and can result in troublesome direct dewatering of hydrocyclone underflow. The -1.0 mm fraction in goethitic iron ores is typically considered as waste. A new two-stage wet gravity separation flow sheet, referred to as the ædesandÆ process, has been designed to overcome these issues for the upgrading of low-grade clay-rich goethitic or hematite-quartz fine iron ores. The desand process is designed to treat the -1.0 mm range from -8.0 mm natural fines, to recover a -1.0 +0.038 mm higher-grade fraction by rejecting to tailings any low-grade clay-rich ultrafines and low density sand-size fine chert/quartz gangue and shale.The desand process consists of wet screens with a nominal 0.7-1.0 mm cut point which direct the undersize to hydrocyclones. The hydrocyclone underflow is then fed to upcurrent classifiers where the classifier middlings is sent to spirals and classifier and spirals concentrates are then dewatered using vacuum belt filters or fine screens. The three product upcurrent classifier is employed to further deslime the hydrocyclone underflow, producing firstly a coarse final concentrate, and then a deslimed middlings for feeding to spirals as well as a 0.100 mm clay and fine quartz or banded iron formation (BIF) sand in final overflow for feeding to the residue thickener. The upcurrent classifier middlings provides the spirals with a significantly cleaner feed material than traditional methods, with the end result that the spirals do not silt up with slimes and therefore can continue to run at their optimum. The upcurrent classifier and spirals form a complimentary pair, with the upcurrent classifier better able to send coarser, acceptable grade particles to concentrate and fine slimes to tailings whilst allowing the spiral to better reject coarser, subgrade low specific gravity particles. Test results for the Mayoko-Moussondji iron project, Republic of Congo, using upcurrent classifier-Wilfley Table (simulating spirals) gave acceptable mass recovery from run-of-mine (ROM) and Fe recovery from hydrocyclone underflow for HEMCOL (6.2 per cent mass recovery from ROM/43.1 per cent Fe recovery) and HEMBIF2 (5.1 per cent mass recovery from ROM/22.3 per cent Fe recovery) mineralisation types. The desand process also enables improved dewatering of -1.0 +0.038 mm product from a clay-rich plant feed.A number of new wet plants in the Pilbara use the desand flow sheet including FMGÆs Cloudbreak and their two Christmas Creek plants. Many potential new applications are being explored, with new iron ore plants in India as well as those being proposed for West Africa. Operational experience has highlighted the importance of providing clean process water to the upcurrent classifiers as well as ongoing design improvements including increased wear life, reduced maintenance and enabling a more steady feed rate to spirals.CITATION:Clout, J M F, 2013. Beneficiation of fine iron ores using the desand process, in Proceedings Iron Ore 2013 , pp 337-348 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By K Knorr, S Birch

The mineralogy of new certified-reference-materials (CRM) for X-ray fluorescence from Western Australia (ASCRM 030 to 035) was analysed by X-ray diffraction using the BRUKER energy dispersive one-dimensional detector LYNXEYE-XE. The samples were studied using standard-less quantitative phase analysis, based on the Rietveld method. This method delivers the relative amount of crystalline phases. All materials were found to be high-grade iron ore predominantly consisting of hematite and goethite and very low amounts of magnetite. In addition, the gangue mineralogy was characterised. It consists of low-per cent amounts of carbonate (siderite/calcite), quartz, kaolinite, chlorite and gibbsite.Furthermore, all samples were analysed with the external standard method. This is an elegant way to probe for amorphous content without adding an internal standard. All six samples were found to contain up to 16 per cent amorphous or nano-crystalline material.CITATION:Knorr, K and Birch, S, 2013. Mineralogy of new Australian x-ray fluorescence standards, in Proceedings Iron Ore 2013 , pp 269-274 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By N van Aarde, B A. Moore, S van der Merwe

Frequently materials handling operations are compromised by transfer chute problems ranging from high wear rates, blockages and ineffective loading of the downstream conveyor. This paper will present the design flow implemented to overcome problems in two case studies utilising discrete element modelling incorporating material characterisation.Material testing is relevant in achieving a valid discrete element method (DEM) simulation model and subsequently a valuable design tool for transfer chute assessment and design. It is well recognised that in the current growth and demand for mineral resources, leading to ever increasing conveyor capacities associated with export terminals and mineral processing facilities that transfer chutes are a key focus point. The successful performance of the transfer chute is also dependent on operating with a ærobust rangeÆ of material flowability and handling characteristics. This requirement is crucial in accommodating mineral ores from developing resources, which are often more friable and stickier than in past decades.This paper will include details of chute installations associated with iron ore and coking coal, from the DEM simulations through to the performance of the installed and commissioned plant.CITATION:Moore, B A, van der Merwe, S and van Aarde, N, 2013. Implementation of advanced transfer chute designs, in Proceedings Iron Ore 2013 , pp 445-450 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By H Thanasekaran, L Christodoulou, J Kohmuench

"Column flotation has been successfully applied to iron ore concentration since the 1980s with the goal of reducing silica content and allowing for the efficient production of pellet feed. Since then, columns have been widely used in iron ore processing due to: their lower capital and operational costs when compared to conventional cells their ability to generate higher concentrate grades and recoveries.Currently, more than 100 columns have been installed within Brazilian iron ore processing circuits for rougher, cleaner and scavenger duties. Despite it being a well-established approach, several technological advances have improved column design, accessories and performance. This work presents the performance of some iron ore columns in Brazil and the recent technological developments.CITATION:Thanasekaran, H, Kohmuench, J and Christodoulou, L, 2013. Column flotation of iron ore - status and advances, in Proceedings Iron Ore 2013, pp 479-484 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By P J. Marsh, P J. Bartsch, N J. Semler

Iron Road Limited is currently studying the feasibility of producing 20 Mt/a of high-grade (67 per cent Fe) magnetite concentrate from a 2.6 Bt resource (JORC) located at Warramboo on the central Eyre Peninsula in South Australia. Bulk concentrate has been tested at a relatively coarse grind size of -106 ¦m. The preliminary flow sheet has been confirmed based on initial mine plans and comprehensive metallurgical testing across the range of mineralisation. Extensive Davis tube testing to predict magnetite recoveries has been conducted over the resource, however this was completed at settings different to the optimised settings developed in the metallurgical test work program.This paper outlines the development of an ore treatment simulation in SysCAD which utilises the mine production plan, the Davis tube test data from the resource, data from metallurgical test work and process design criteria to predict magnetite concentrate deliveries. Mineralogical data, including QEMScan results and metallurgical assessments, were a fundamental basis of the process models which enable predictions of concentrate yield and quality. Power and water requirements are also calculated within the model. SysCAD dynamic simulation has been used to assist with the design of the process plant and downstream infrastructure. The simulation has been set-up to allow iterative integration and optimisation of the mine plan when it becomes available.CITATION:Semler, N J, Marsh, P J and Bartsch, P J, 2013. Iron RoadÆs prediction of magnetite concentrate production from the Central Eyre Iron Project, in Proceedings Iron Ore 2013 , pp 539-546 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By T Krull, T J. Donohue, D Ilic

"Problematic issues in materials handling applications are often amplified in the iron ore industry due to the relatively high density of the ore as well as the abrasive nature of the product. One of the main issues arising from the handling of iron ore is excessive wear, with two applications typically suffering accelerated wear issues being transfer chutes and conveyor belts. These wear issues are problematic due to additional capital costs, but mainly due to the associated downtimes resulting in the accelerated wear. This study will focus on the modelling of iron ore in practical applications where design work was undertaken in order to reduce the wear rates of different materials handling equipment.CITATION:Donohue, T J, Ilic, D and Krull, T, 2013. Modelling of iron ore in materials handling applications with a focus on wear, in Proceedings Iron Ore 2013, pp 355-362 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By M Sherman

The challenge facing the engineering provider is to calculate throughput rates when faced with disparate specific energies calculated by different testing methodologies. Typically, an ownerÆs team would expect that the throughput calculations be checked using more than one method, therefore it is inevitable that there will be differences, based on which methodology is used. This engineering challenge is exacerbated by the continuing evolution of contemporary circuit configurations such as two stage pebble crushing with or without high pressure grinding rolls (HPGRs) as the second stage, or second stage pebble crusher product reporting to the ball milling circuit, etc.This paper is a companion to the paper first presented at SAG 2011, which showed that the Bond Indices are an excellent tool for estimating the specific energy requirements for semi-autogenous grinding (SAG) mills in single-stage SAG milling (SSS) circuits, SAG and ball mill circuits (SAB) or SAG and ball mill circuits with pebble crushers (SABC). This paper presents how the Bond Indices have been used to calculate ball mill specific energies, and therefore throughput rates, for SAG mill based circuits. Once the ball milling specific energy is known, tower mill and vertimill energy requirements can also be calculated. It is noteworthy that the method presented in this paper does not require the use of any unpublished correction factors: the proposed method uses the Bond parameters and equations published by Rowland in 1982.CITATION:Sherman, M, 2013. 21st century bond, in Proceedings Iron Ore 2013 , pp 309-312 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By A Wanninayake, E Novello, I Gillani

A residue storage facility (RSF) was designed to cater for Davidson Creek Area and Robertson Range Area operations under the FerrAus Pilbara iron ore development project in the Pilbara Region, Western Australia. Annual ore production was about 15 million tonnes over a period of up to 15 years. The RSF was designed to handle a tailings production rate of 2.2 Mt/a over the project life with ability to be expanded at a later date. The composition of tailings was predominantly -45 ¦ material with some spiral reject material. The fraction of solids was expected to be between 40 per cent and 50 per cent solids by weight.The RSF was designed as an above ground storage facility, integrating with a mine waste dump planned close to the selected RSF site. This integration helped to increase the stability of the RSF embankment and to reduce the construction cost. The main source of construction material for the remaining part of the RSF embankment was selected to be mine waste. The RSF was designed to be constructed in stages by considering the availability of mine waste according to the mining schedule. The use of mine waste for construction of RSF embankments has several benefits over use of borrowed material. These include less construction costs and less disturbances to the environment, by minimising borrowed areas and waste dump footprints.CITATION:Wanninayake, A, Novello, E and Gillani, I, 2013. Effective use of mine waste in the design of a residue storage facility, Pilbara region, Western Australia, in Proceedings Iron Ore 2013 , pp 39-44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By H Han, W Wang, E Zhou, D Duan

"In this study, physical, chemical and microscopic characteristics of high phosphorus oolitic hematite were studied firstly. Based on which, the new methods of high phosphorus hematite used in the æsolid state reduction by rotary hearth furnace - magnetic separationÆ and iron nugget by rotary hearth furnace direct reduction processes were discussed. The results showed that high temperature, low basicity and high carbon content is conducive for the apatite in iron ore to reduce into molten iron, but not conducive to the removal of phosphorus. Through optimisation of process parameters, dephosphorisation rate of high phosphorus hematite is more than 60 per cent by æsolid state reduction roasting-magnetic separationÆ process while that is up to 80 per cent by iron nugget process. This study can provide theoretical and technical basis on economical and rational use of high phosphorus oolitic hematite.CITATION:Han, H, Duan, D, Zhou, E and Wang, W, 2013. New methods for high phosphorus oolitic hematite dephosphorisation by direct reduction process, in Proceedings Iron Ore 2013, pp 391-396 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By K C. Williams, A W. Roberts, J D. Prigge

For stockpile design, the flowability and structural interfaces are critically dependant on the stress conditions throughout the pile. Historically, the predictive methodologies for stress determination have been too conservative, which adds inefficiency to the stockpile reclaim interface selections, especially for live reclaim stockpile systems. In addition, accurate pressure profiling throughout stockpile is essential to correctly design the stockpile support structures, which are buried within the stockpile. Such buried structures include trestle legs or columns to support load-out conveyors or the roof of bulk storage sheds. Improved methodologies with respect to the development of the hoop stress condition which exists in material ædrawn-downÆ within the stockpile has been developed. This hoop stress approach has significantly improved the live capacity prediction to over 90 per cent accuracy and improved rathole structure prediction within live reclaim stockpiles. Additionally the methodologies in estimating the vertical and circumferential stress variation acting on buried stockpile structures have been significantly progressed, with experimental testing shown good agreement with the theory.CITATION:Williams, K C, Roberts, A W and Prigge, J D, 2013. Recent developments in stress analysis and live reclaim prediction within iron ore stockpiles, in Proceedings Iron Ore 2013 , pp 501-510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By S Hapugoda, J R. Manuel, M J. Peterson, A Poliakov, E Donskoi

The occurrence and deportment of manganese in a number of ferromanganese and Mn-bearing iron ore samples from supergene-upgraded deposits, as well as from magnetite banded iron formation (BIF) and magnetite skarn deposits, was characterised in order to provide a basis for improved understanding of the processing characteristics of different ore types and investigate the potential for development of a robust geometallurgical classification for Mn-oxide ores. An understanding of the Mn mineralogy in mixed Fe-Mn deposits is necessary to inform any attempt to separate the Fe and Mn during beneficiation and to understand and predict the behaviour of lump and fine ore products during processing.A suite of analytical techniques was utilised, including hand sorting of lump ore particles, optical microscopy, X-ray fluorescence (XRF)/inductively-coupled plasma mass spectrometry (ICP-MS) chemistry, X-ray diffraction (XRD), scanning electron microscopy (SEM)/electron probe microanalysis (EPMA) and gas and solid phase pycnometry, in order to elucidate manganese mineralogy, mineral chemistry and mineral textures. Manganomelane group minerals (eg cryptomelane, hollandite), pyrolusite and lithiophorite were the most common manganese oxides in the samples examined. From the microprobe work, there was evidence of probable substitution of Mn, as well as Al and Si, into the structures of goethite and hematite. Manganomelane minerals were often intimately associated with goethite, in particular, and a clarification of this association and the associated Si and Al impurities is fundamental for improved understanding of beneficiation and sintering behaviour of Mn-oxide ores. Due to the poor or very fine crystallinity of some supergene manganese deposits and of some Mn oxide minerals, in particular the extent of overlapping peaks and their variable mineral chemistry, XRD was a problematic technique to equivocally determine Mn mineralogy.For lower-grade, earthy, poorly microcrystalline ores the mineralogical and textural association between mixed Mn, Fe and Al (¦ Si) phases was also critical. The deportment and potential separation of these elements in these deposits, especially Al, was complex, as they were characterised by forms of æhydrousÆ cryptomelane with higher levels of Fe-Al-Si substitution, as well as intimate intergrowths of ochreous-earthy goethite (probably aluminous in part) with cryptomelane, lithiophorite and/or kaolinite.Trace amounts of alkali elements in ferromanganese deposits were considered likely to be preferentially structurally associated with Mn oxides, while lateritic deposits with significant amounts of lithiophorite could contain elevated levels of deleterious impurities; Co and Ni in particular.A combination of solid and gas phase pycnometry proved to be a useful technique for broadly discriminating hematitic, goethitic and mixed Mn oxide-goethite lump particles based upon differences in their envelope and apparent densities. Based upon these preliminary results and ongoing Raman spectroscopy work on manganese deposits sensu stricto, Raman spectroscopy is a technique considered to have promise during targeted research to better link the optical and compositional properties of ferromanganese ore particles. CT-scan (computed tomography scan) analysis could also be combined with Raman spectroscopy and pycnometry to link mineral composition, mineral texture, ore particle textures and particle porosity/permeability to the high-temperature processing behaviour of lump and fines products.CITATION:Peterson, M J, Hapugoda, S, Manuel, J R, Donskoi, E and Poliakov, A, 2013. Textural characterisation of manganese minerals to improve the geometallurgical characterisation of ferromanganese and iron ores, in Proceedings Iron Ore 2013 , pp 281-300 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By R Dwyer, S Rea, W J. Bruckard, N McSweeney, R Holmes

"The innate ability of microorganisms to adapt to changing or inhospitable environments has often been exploited for industrial purposes and forms the basis of many current biotechnological processes. The ability of bacteria to adapt and adhere to specific mineral surfaces ensures that the energetic or nutritional requirements of the cell are met and often serves as a survival mechanism under unfavourable?growth conditions or conditions of stress. In this process, cells may rearrange or modify the macromolecules expressed on the cell surface itself or produce extracellular molecules, modifying mineral surfaces to render them more suitable for growth. The modifications that these molecules produce on mineral surfaces may result in changes to the surface charge and hydrophobicity of a mineral. As a result, these biomolecules may have some potential application as flotation collectors or modifiers.In this work, the effect of long-term exposure of Paenibacillus taiwanensis to goethite and common gangue minerals associated with Australian iron ores on the differential expression of membrane and extracellular proteins was determined. Both groups of proteins play a role in cell adherence to mineral particles. Cells were adapted to grow in the presence of each mineral over time. The proteins expressed on the cell membrane and the extracellular proteins excreted by the cell were isolated and analysed by two-dimensional polyacrylamide gel electrophoresis (2D gel PAGE). The outcomes of these studies are presented here and potential application of these products for flotation discussed.CITATION:Dwyer, R, Rea, S, McSweeney, N, Bruckard, W J and Holmes, R, 2013. Microbes and their metabolites - potential iron ore flotation reagents, in Proceedings Iron Ore 2013, pp 369-372 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By A-A Latscha, C Boyle

Geological modelling has historically been done using sectional interpretation of paper sections or on a computer screen. Boundaries of geological units or grade shells are interpreted by a geologist section by section and the shapes are drawn onto paper to be digitised later or they are directly digitised into a computer. This approach is referred to as explicit modelling. Such methods are time consuming if there are many section lines or boundaries to be interpreted. The number of metres drilled and resource models made is increasing each year and it will be difficult to keep up using explicit modelling methods. Alternatively, it is possible to use information carried in the drill holes, known geological relationships and point estimation methods in two or three dimensions, to create similar geology boundaries, while eliminating or at least greatly reducing the need to manually interpret and digitise detailed sectional interpretations. Such methods are referred to as implicit modelling and are available in a number of software packages. Implicit modelling approaches have been used in iron ore and found to significantly reduce the time needed for modelling while producing results that are comparable or better than standard explicit modelling approaches. A number of case studies have been undertaken of implicit modelling in iron ore deposits. Stratigraphic surfaces of bedded, folded and faulted iron ore deposits have been modelled in various deposits by Leapfrog Geo, GOCAD (with SKUA) and Vulcan Integrated Stratigraphic Modelling. Leapfrog Mining was used to model iron grade shells at particular cut-off grades. The modelled surfaces are of a high standard equivalent to those that could be produced by traditional explicit modelling but the time required by the implicit methods is far less. Implicit geological modelling is an active area of software development and improvements in software are likely.CITATION:Boyle, C and Latscha, A-A, 2013. Implicit geological modelling of iron ore deposits, in Proceedings Iron Ore 2013 , pp 57-66 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By J E. Everett

When ore is being selected from a regularised block model, a common procedure is to accept as ore any block whose iron content exceeds a cut-off value, and whose content in each contaminant analyte is below an appropriate cut-off value. This method defines a quadrant within the multidimensional analyte space, such that any block lying within the quadrant is accepted as ore and any block lying outside the quadrant is rejected as waste. The cut-off levels can be adjusted to maximise ore tonnage at a target grade (or analyte vector). When the method is applied to a project comprising multiple pits with systematically differing grades, it is found that ore tonnage at target grade is maximised if different cut-off quadrants are used for the different pits. This is apparently illogical, because it implies that an ore block from one pit may be accepted as ore, but an identical block from another pit is rejected as waste, even when ore from both pits is to be blended into the same product and there are no production cost differences between the pits. The paradox is an example of the ætheory of the second bestÆ: if there are multiple conditions for optimality and one condition is broken, then obeying the other conditions may not be the best policy. The problem lies with the quadrant cut-off method, which is shown to be inconsistent even for selecting ore from a single pit. A criterion that is inconsistent cannot be optimal. It is shown that a linear composite cut-off function provides maximum ore tonnage, and that a single composite cut-off criterion is consistent and optimal over multiple pits. Further, it is shown that a composite cut-off function not only maximises ore tonnage at a specified composition, but also can be used to select ore so as to maximise project value, if marginal costs and values are available.CITATION:Everett, J E, 2013. Selection of ore from multiple pits, in Proceedings Iron Ore 2013 , pp 185-192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By J Law, S Jahanshahi, R Holmes

Iron ore is AustraliaÆs largest commodity export and is vitally important to AustraliaÆs current and future prosperity. However, while major expansions are currently in progress to satisfy demand, the industry is also undergoing major transformations. Reserves of traditional high-grade Brockman ores that have underpinned the Australian iron ore industry since its inception are slowly being depleted and alternative ore types such as Marra Mamba bedded iron deposits, Yandi and Pannawonica channel iron deposits and magnetite deposits are now being developed. However, the impurity levels in some of these alternative ores are higher and they require blending and/or upgrading as well as an advanced knowledge of their downstream processing characteristics to facilitate cost-effective utilisation by overseas customers. The research challenge is to use advanced techniques for mineral exploration, ore characterisation, mineral beneficiation, agglomeration and sustainable processing to identify and develop innovative and breakthrough options for locating, unlocking and enhancing the value of AustraliaÆs iron ore resources. Furthermore, to sustain the steel industry and hence secure the demand for iron ore, there is a growing need to enhance the environmental and business performance of the industry through reductions in wastes and emissions. Therefore, cost-effective breakthrough and enabling technologies that massively cut waste generation, CO2 emissions and water consumption are also being developed. These include the use of renewable fuels and reductants, waste heat recovery and conversion of by-product slag into a saleable substitute for Portland cement. A number of examples of recent developments in the above areas are provided in this paper.CITATION:Holmes, R, Jahanshahi, S and Law, J, 2013. Research and innovation for the iron ore to carbon steel value chain, in Proceedings Iron Ore 2013 , pp 3-6 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Y Ren

?ptim?sgtion t?ols nos ope? 0iu ?ingc s?ch as the cche??ling and?pi? k?(i?isatTon tool{ ?ave bg?ome(?osd-dvfective way? to e?iluata open`¦it mi~e!p?n?ept as w?ll asá?}prmv?ng mine?projecW`value> ?owerez

Aug 12, 2013