Search Documents

By P Hawke, J Hurst, B KrapeP

Hancock Prospecting Pty Ltd (HPPL) drilled two deep diamond stratigraphic holes (ECD0001 and RHD0296) within the eastern Fortescue Valley in the Pilbara of Western Australia. Located south of the Roy Hill Iron Ore project, the holes aimed to define the stratigraphy of the Marra Mamba Iron Formation (MMIF) of the Chichester Range and its south-dipping extensions below recent cover. Previous attempts to define the MMIF of the Chichester Range have resulted in differing interpretations due to the data available at the time.The unweathered MMIF beneath the Fortescue Valley in the HPPL drill holes is characterised by dolomitic carbonate interbedded with stilpnomelane-rich shales, chert and banded iron formation (BIF) with hematite staining. This intersection equates to ~75 m of carbonate-facies iron formation, as opposed to the ~230 m thick oxide-facies BIF and shale sequence encountered south of the Fortescue Valley.Various detailed geological core analyses and interpretations from ECD0001 and RHD0296 were integrated with regional diamond and reverse circulation (RC) holes from across the Fortescue Valley. Interpretation of the data indicates that the eastern Fortescue Valley MMIF represents a thinned thickness sequence of the whole formation. The MMIF of the Chichester Range and Fortescue Valley has gamma logs that correlate strongly in parts to the type section used for MMIF south of the Fortescue Valley. Therefore, the outcropping MMIF in the Chichester Range represents an eroded equivalent of the æreducedÆ thickness MMIF observed in ECD0001 and RHD0296.Data from deep diamond drill holes across the valley, from the Hamersley Basin to the Carawine Basin, were correlated. The correlation shows that the depositional site of the MMIF in the HPPL diamond drill holes is consistent with a proximal ramp setting, in which iron-rich shales wedge up-palaeoslope and shelf-derived carbonate turbidites wedge down-palaeoslope. Not only is it the occurrence of these shales that define the MMIF, but they also determine the northward potential to develop orebodies, as they are the source of iron from which iron-rich oxides and carbonates of metamorphic or diagenetic origin form.CITATION:Hurst, J, KrapeP, B and Hawke, P, 2013. Stratigraphy of the Marra Mamba iron formation within the Chichester Range and its implications for iron ore genesis at Roy Hill - evidence from deep diamond drill holes within the East Fortescue Valley, in Proceedings Iron Ore 2013 , pp 91-106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By J Visser

Dust mitigation has long been seen as nothing more than managing a nuisance issue, but the reality is that poor dust management can lead to one or more of the following negative consequences: an increased risk of safety incidents, lost revenue, reduced and possibly even lost licence to operate, regulatory intervention, high staff turnover and/or absenteeism and occupational health and safety (OH&S) issues. Dust mitigation and management is not a black art; rather it is a scientifically driven process that can provide an opportunity to increase profits, increase the companyÆs status as an excellent corporate citizen, enhance staff retention and reduce the safety risk profile of the operation.The way to achieve success in dust mitigation and control is to apply the scientific method to each problem that can arise and plague any operation by using current industry best practice. This method of dust problem-solving can be applied to dust issues arising from specific dust sources and locations. The dust sources can include wind impacting on stockpiles, open areas, tailings storage facilities, moving train and truck loads, vehicular traffic on roads, the operation of shovels, front end loaders, draglines and other equipment, as well as ore movement on conveyors.The solutions will come from a combination of deployment of dust collection equipment, dust and moisture monitoring equipment, the appropriate application of water and chemicals, the introduction and maintenance of appropriate barriers and the use of predictive data from local and public weather stations. The paradigm shift required is to view dust mitigation as one aspect of normal operational practice, not a ænice to haveÆ or æunnecessary expenseÆ as most operators currently view it. This attitude is becoming more important as more and more local communities oppose the development of mines. One of the reasons for this local opposition is the inevitable dusty environment that is usually associated with mining.Dust mitigation is not a significant expense if correctly designed and included into the system, either as part of the original design of the operation or as a brownfield installation after the fact. Indeed, there is always a loss of revenue associated with dustiness resulting from ore movement and avoiding this goes a long way to paying for any associated dust mitigating costs.CITATION:Visser, J, 2013. Dust mitigation - changing the paradigm, in Proceedings Iron Ore 2013 , pp 27-38 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By E K. Leeka

Process control limitations have led to suboptimal performance of the crushing section of Sishen MineÆs Jig Plant. The performance of the PID (proportional-integral-derivative) controller implemented during commissioning was hampered by the relatively small buffer capacity between the crushers and screens. The inability to maintain the tertiary crushing chamber under full choke conditions lead to inefficient crushing and reduced crusher product cubicity.Model predictive control (MPC) was implemented in the tertiary crusher plant in May 2012 and resulted in a throughput improvement of six per cent in its first month. The controller was further optimised and indicated a throughput improvement of 16 per cent during on/off testing in July 2012. The throughput improvement is attributable to the finer crusher product resulting from operating the crusher under full choke conditions and controlled feed rate to the tertiary crusher plant screens. The next step is to couple the model predictive controller, automated gap control system and an economic optimiser to ensure maximised throughput and value from the resource.CITATION:Leeka, E K, 2013. Performance of model predictive control on the crushing circuit at Sishen Mine, in Proceedings Iron Ore 2013 , pp 417-420 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By C Ward, U Mueller

Compositional geostatistics is an approach developed to ensure that the constant sum constraint induced by geochemical iron ore analysis is respected in estimation and simulation. Jack-knifing and cross-validation were used within this framework to compare the results from ordinary cokriging of the additive log ratio (alr) variables with those from conventional ordinary cokriging. Two methods were used to back-transform the alr estimates: the crude additive generalised logistic back transformation and numerical integration via Gauss-Hermite quadrature. Previous work on a blasthole data set from a Yilgarn iron ore mine showed promising results, with the Gauss-Hermite quadrature method returning results comparable to ordinary cokriging from the point of view of bias, but superior in that the constant sum constraint imposed by geochemistry of the data was honoured. Other practitioners have noted that the linear interpolation of non-linear log ratio transformations will result in biased results, and that this bias can be masked in a (grade control) setting where the spatial density is high. To test this assertion, the methodology has been extended to successively lower spatial density data sets. The results and applicability to routine iron estimation are discussed.CITATION:Ward, C and Mueller, U, 2013. Compositions, log ratios and bias - from grade control to resource definition, in Proceedings Iron Ore 2013 , pp 313-320 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By K T. Broekman, R L. Koenig

"The Braemar Iron Formation is atypical ore when compared to the current magnetite ores being processed. In attempting to process and economically recover the vast quantities of iron ore stored within the Braemar Iron Formation, æshifting the paradigmÆ is required. The formation has a low Davis tube recovery (DTR) grade of 15 - 20 per cent, which is much lower than magnetite ores processed in Australia. Despite this, by thoroughly testing and understanding the ore characteristics, it is found that the Braemar ores have significant advantages to processing than the harder banded iron formation (BIF) and taconite resources.The Hawsons magnetite iron ore resource has been known from the early 1960s when CRA explored the area. The grade was low and the Pilbara region discovery lead to the development of high-grade direct shipping hematite ores. Carpentaria Exploration (CAP) rediscovered the magnetite whilst undertaking multi-commodity exploration in the Broken Hill district during 2009. Shifting the paradigm away from grade the advantages of processing this ore are achieved by having an extremely low waste to ore ratio, lower Bond work index, lower abrasion levels and high-grade magnetite concentrates with little impurities other than silica. While developing the Hawsons Iron Project (HIP) it became more apparent that a positive business case is achievable when the following factors are exploited: very large resource - the resource is contained within one pit the rock fractures easily along grain boundaries - ideal for cheap impact crushing of the ore the ore is extremely soft, with a Bond work index of 6.3 - 8.0 kWh/t all major infrastructure required is readily available - rail, power, access and port the mine is in close proximity to Broken Hill - rich mining history and skill set available the resource contains many billions of tonnes of magnetite mineralisation.Shifting the paradigm by selecting equipment suitable for processing soft ores and not hard BIF or taconite ores and taking locality and available infrastructure into account may change the way people approach new low-grade resources in future.CITATION:Koenig, R L and Broekman, K T, 2013. Understanding ore characteristics and equipment selection, in Proceedings Iron Ore 2013, pp 403-410 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By T C. Ooi, L Lu

Owing to ongoing development of new orebodies and changes to existing mining operations, new ore types with distinct mineralogy, porosity and textures are generated as feed for iron and steelmaking. Moreover, further product differentiation occurs as fine ores are increasingly beneficiated to achieve grade. A study was necessary to characterise a suite of iron ore fines in terms of their propensity for formation of quasi-particles and green bed permeability prior to sintering. In this study, two Marra Mamba bedded iron deposit (BID) samples, one Pisolitic channel iron deposit (CID) samples, two dense hematite samples (coarse and fine grained microplaty hematite), one hematite-goethite BID samples and one hematite-goethite bedded/detrital iron deposit (BID-DID) composite sample were investigated. Both Marra Mamba fines and Pisolitic fines exhibit the highest green bed permeability followed closely by hematite-goethite fines, fine microplaty hematite fines, hematite-goethite BID-DID composite fines and coarse microplaty hematite fines at a moderate sintering bed depth of 500 mm. While porous fines generally form better quasi-particles upon granulation than dense fines, the amount of moisture addition increased due to the moisture saturation of the porous fines. As sinter strands become ever larger and deeper, it was necessary to examine the granulation performance of these ore types at a range of bed depths ranging from 300 to 900 mm. On average, the green bed permeability achieved by different ore types, decreased by approximately 7.5 - 9 Japanese Permeability Unit (JPU) as the bed height was increased from 500 mm to 900 mm. In order mitigate the effect of lower bed permeability of the deeper beds, small additions of hydrated lime were investigated as a binding agent to facilitate the formation of strong micro-pellets. With the addition of three per cent hydrated lime, equivalent to approximately 2.3 per cent burnt lime, the majority of fines achieved adequate permeability for deeper bed sintering, with the exception of coarse microplaty hematite fines. In simulated coastal steelmaking sinter blends, it was found that the overall granulation performance of the blend is contributed to by individual fines constituting the blend. Therefore fines possessing favourable granulating properties impart better granulation to the blend as a whole.CITATION:Ooi, T C and Lu, L, 2013. Effects of ore type and binder addition on the formation of quasi-particles and green bed permeability at different sintering bed depths, in Proceedings Iron Ore 2013 , pp 459-466 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By A J. Cornah

Critical decisions in iron ore project evaluation and production are based on global and local spatial estimates of primary mineral deposit properties (such as in situ geochemical grades) and geometallurgical responses (such as screened, washed or concentrated product yields and grades), which are derived from limited sample data. These spatial estimates are typically made using classical geostatistical techniques, which fundamentally assume that the attributes of interest behave additively. This assumption is generally appropriate for æprimaryÆ variables but æresponseÆ variables may behave non-additively and therefore their direct linear estimates may be biased.In this paper an existing additivity testing mechanism is used to quantify the bias resulting from direct linear estimation of a non-additive iron ore attribute. Data from a magnetite project are used to determine the circumstances under which such biases may be of material impact. The implications for iron ore resource estimation, geometallurgical modelling and grade control are outlined and discussed.CITATION:Cornah, A J, 2013. Assessment of the impact of non-additivity in the estimation of iron ore attributes, in Proceedings Iron Ore 2013 , pp 129-136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By P Hogan, M Wells

Reflectance spectroscopy has become an established technique for mineral exploration and ore characterisation. However, there are few reported cases where the technique has been applied to the Hamersley Province channel iron deposits (CID). The Bonnie Creek CID, located ÿ140 km north of Newman in Western Australia, represents one of a number of CIDs recently discovered in the Hamersley Province. Reflectance spectroscopic analysis using the CSIRO HyLoggerÖ automated scanning system, in conjunction with X-ray diffraction and compositional analysis, was used to characterise and map the ore and gangue mineralogy in CID drill core. Using CSIROÆs spectral mineral characterisation scripts, it was possible to map the downhole distribution of the Fe-oxide abundance, hematite:goethite ratio and the gibbsite and kaolinite abundance. Spectral estimates of kaolinite abundance were found to be closely related to loss on ignition measurements at 650¦C and the spectral kaolinite abundance index provided a reliable estimate of the total weight percentage Al2O3 content. In addition, downhole HyLoggerÖ scanning of diamond drill core reliably mapped the distribution of kaolinite as supported by coincidentally elevated contents of alumina and silica. Furthermore, spectrally-derived estimates of iron oxide abundance were well related to assayed Fe wt per cent contents and use of the spectral iron oxide mineral index mapped the distribution of the goethite:hematite ratio, and demonstrated that material logged as high-grade ore in the Bonnie Creek CID was predominantly goethite-rich.CITATION:Wells, M and Hogan, P, 2013. Bonnie Creek channel iron deposits ore mineralogy - insights using the HyLoggerÖ technology, in Proceedings Iron Ore 2013 , pp 321-328 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By M Eggers, H Baxter

This paper discusses the geotechnical condition of bedding shears and small- and large-scale faults and shears in Archean banded iron formation (BIF) bedrock, based on observations of core and televiewer images. Information that can be collected includes the orientation of defects, infill thickness, strength and material type, defect shape and surface roughness.The spacing and continuity of bedding shears may be critical to slope design where performance is structurally controlled with bedding dipping out of a wall. The intensity of development of the bedding shear is a useful indicator of the amount of shearing a bedding surface has been subjected to. This can allow for engineering judgement to be used in adopting peak or residual shear strengths along defect surfaces when developing the design.The spacing and continuity of bedding shears may also contribute to the blockiness and degradation of a rock mass where the structural orientation is otherwise favourable. Additionally the condition, thickness and strength of infill of major fault structures can affect slope design and performance, depending on orientation.Comparison of the condition of structures observed in core with the corresponding in situ televiewer image has been made to assess what characteristics are most accurately captured by each technique and whether the additional information gathered from using the televiewer technique is justified by the cost. The question of whether the data collected by a televiewer is sufficient to ultimately replace the need for core is considered.CITATION:Baxter, H and Eggers, M, 2013. Fault and shear characterisation in archean banded iron formation bedrock - a comparison between core and televiewer data collection techniques, in Proceedings Iron Ore 2013 , pp 47-56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By T Do, J Siliezar, M Larson

With the expansion of magnetite projects in Australia has come the opportunity to take advantage of newer technologies that were not necessarily available when the magnetite industries of North America and Europe were maturing. One of these technologies is the IsaMill, originally developed for the economic treatment of ultra-fine grind (UFG) duties of Mount Isa Mines. As understanding of the IsaMill has increased, so too has the ability to process coarser feeds while maintaining the same energy efficiency advantage and tight product size distribution that originally made the IsaMill so attractive. In the case of magnetite the hard non-elastic ceramic grinding media is ideally suited to the grinding duty when compared to steel grinding media. The centripetal separator and naturally steep product size distribution curve provide a mill discharge that maximises the critical concentrate grade. This paper analyses the effect of the IsaMill grinding technology on the full-scale Ernest Henry Mine (EHM) magnetite operation along with pilot and lab scale demonstrations of optimisation. Issues encountered and the solutions to maximise the mill throughput and quality are examined in an effort to promote better understanding across the industry. CITATION:Larson, M, Do, T and Siliezar, J, 2013. Enhancing magnetite returns - the benefits of IsaMilling, in Proceedings Iron Ore 2013 , pp 411-416 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By P Martin, A Somarin, S Bailey

Field-based research was conducted to investigate the performance of field portable X-ray fluorescence (FPXRF) in the analysis of reverse circulation (RC) drill chips in iron ore exploration. For years, FPXRF has been considered unsuitable for iron ore exploration due to the limitations of the elements it is capable of analysing for, in particular its inability to measure light elements (Mg, Al, Si, P, S). With the advent of the use of silicon drift detectors (SDD) in FPXRF, light elements are now measurable elements. However, doubt over the appropriate use of this new technology still exists due to the absence of reliable comparative field data. These doubts concerned the ability of the FPXRF data to correlate strongly with the laboratory assay of the same samples. It was believed that inconsistent grain size and other variables not being controlled would contribute greatly to this perceived unreliability.We tested RC chip samples on-site in the Pilbara, with the portable Thermo Scientific Niton XL3t X-ray fluorescence (XRF) analyser for a range of elements including Fe, Mn, Al, Si and S and then compared the results with laboratory assay data. A strong correlation indicates that the FPXRF results are reliable. Furthermore, to show the effect of simple sample preparation, we also analysed pulps of the same samples in the same way.The correlations were good for all of the elements of interest for the RC chip samples (R2 values between 0.82 and 0.9), and excellent for the pulps (R2 values between 0.89 and 1). The results also showed a direct correlation between sample preparation and improved quality of results with the FPXRF. This indicates that FPXRF can produce data from unprepared RC chips for Al and Si that, when compared with laboratory assays, is reliable for a field application in drilling and grade control. CITATION:Somarin, A, Martin, P and Bailey, S, 2013. Non-destructive analysis of diamond core for light elements using Niton field portable x-ray fluorescence, in Proceedings Iron Ore 2013 , pp 117-230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By R Zhang, J Xu, X Lv, C Bai, S Zhang

This paper studies the grinding behaviour of vanadium-titanium magnetite concentrate in a ball mill. The grinding kinetics, surface morphology, lattice distortion, wettability and moisture capacity were analysed. Grinding kinetics equation was established based on population balances model with the size distribution data from a laser diffraction technique. The SEM photos of the ground concentrate showed that the surface gets rough with increasing grind time. Agglomeration of fine particles was enhanced when the grinding time reached 30 minutes. X-ray diffraction results showed that a loss in crystalline occurred with increasing the grinding time. The peaks of the X-ray diffraction patterns are significantly broadened with increasing grinding time. Wettability, characterised by contact angle between the material and water, improved due to the fact that the surface roughness increased with increasing grinding time. Moisture capacity of concentrate ascends abruptly in the first three minutes and then changed slowly with increasing grinding time. The water transfer coefficient in the particles increased rapidly in the first six minutes and then decreased quickly until grinding time reached 12 minutes.CITATION:Zhang, R, Lv, X, Bai, C, Xu, J and Zhang, S, 2013. Wet grinding of ?vanadium-titanium magnetite concentrate in a ball mill, in Proceedings Iron Ore 2013 , pp 511-518 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By E Forbes, G V. Franks

"This study investigates the dual function of a temperature responsive anionic co-polymer of poly (N-isopropyl acrylamide) (PNIPAM) as a selective flocculant/flotation collector. PNIPAM is used for separating hematite from 50:50 mixtures of hematite and quartz, at a variety of particle sizes. The performance of PNIPAM in this system is compared to that of conventional flotation collectors: sodium oleate and sodium dodecyl sulfate. The results of the study demonstrate that anionic PNIPAM used at 50¦C (above the lower critical solution temperature (LCST)) is the most effective flotation collector for hematite particles in the size range between 10 and 20 ¦m. This is attributed to the increased probability of both particle/bubble collision and particle/bubble attachment through the formation of hydrophobic hematite aggregates. Anionic PNIPAM used at 50¦C also produced the highest hematite recoveries for very fine hematite particles (circa 1 ¦m). However this recovery was completely unselective. This lack of selectivity is partially attributed to the activation of quartz particles by PNIPAM, but is thought to mainly occur as a result of entrapment of quartz particles within the matrix of hematite aggregates.CITATION:Forbes, E and Franks, G V, 2013. Selective separation of hematite from quartz by flotation using a temperature responsive polymer, in Proceedings Iron Ore 2013, pp 381-390 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By M I. Pownceby, N A. S Webster, A J. Studer, I C. Madsen, J A. Kimpton, M J. Fisher-White, L Lu

In situ synchrotron X-ray and in situ neutron diffraction-based experimentation have been implemented to characterise the formation of the complex calcium ferrite iron ore sinter bonding phases silico-ferrite of calcium and aluminium (SFCA) and SFCA-I. Experiments were carried out using fine-grained (<20 ¦m) sinter mixtures containing ~77 wt per cent Fe2O3, 14 wt per cent CaO, 3.5 wt per cent SiO2 and 5 wt per cent Al2O3, with diffraction data collected during heating until 1300 - 1350¦C, which was enough to ensure complete melting of the SFCA phases. In the case of the in situ synchrotron experimentation, results showed that altering the nature of the starting sinter mixture (ie substitution of goethite for hematite; substitution of an amorphous Al2O3-based mineral for gibbsite) did not have a significant effect on the thermal stability range of the SFCA phases. It did, however, have a profound effect on the formation and rate of consumption of the calcium-rich ferrite phases C2F and CF, and on the formation mechanisms of SFCA and SFCA-I. The in situ neutron diffraction experimentation is the first described in the context of iron ore sintering, and the observation of both SFCA-I and SFCA formation in the in situ diffraction data represents the first step in achieving the goal of charactering iron ore sinter phase formation in large volumes of industrial sinter starting materials with a wide range of particle sizes (up to 6.3 mm).CITATION:Webster, N A S, Pownceby, M I, Madsen, I C, Studer, A J, Lu, L, Manuel, J R, Kimpton, J A and Fisher-White, M J, 2013. In situ x-ray and neutron diffraction studies of silico-ferrite of calcium and aluminium iron ore sinter phase formation, in Proceedings Iron Ore 2013 , pp 487-494 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By D Kepert, M Absalom, N Nitschke, C Fowers

The discovery of the Nyidinghu Iron Ore Deposit totalling 2.46 Bt of resource continues FortescueÆs highly successful exploration record of discovering multi-billion tonne deposits under cover with little to no surface expression. Since inception in 2003 Fortescue have discovered and delineated the Christmas Creek and Cloudbreak deposits in the Chichester Range totalling 3.38 Bt and 3.25 Bt in the Solomon region. Together with other deposits Fortescues resource portfolio now approximates 10 Bt of hematite - goethite mineralisation.The Nyidinghu deposit is situated on the southern margin of the Fortescue Valley, 35 km south of FortescueÆs Cloudbreak mining operations on the north margin of the valley. Nyidinghu comprises approximately 70 per cent BID martite - goethite mineralisation hosted by the Brockman Iron Formation and 30 per cent CID beneath alluvial outwash of the Weeli Wolli Creek in to the Fortescue Valley. Minor DID mineralisation occurs at the deposit margins.BID mineralisation is strongly controlled by the pre-existing NE/SW trending Weeli Wolli Fault system and bounded to the north by the Poonda Fault. Both fault systems are interpreted to have had a long and complex history commencing pre Ophthalmian Orogeny (ca 2.2 Ga) and remaining intermittently active through the Proterozoic.CID at Nyidinghu is the downstream continuation of the combined Weeli Wolli/Marillana CID palaeochannel system being mined by Rio Tinto and BHP Billiton at Yandicoogina and Yandi, respectively.Exploration commenced in August 2010 with the inaugural resource announcement of 1 Bt being made just six months later. To date over 1700 RC and 85 diamond core holes have been drilled forming the basis for the resource of 2.46 Bt and ongoing feasibility studies. Current exploration activities continue to delineate new mineralisation at Nyidinghu with an ultimate target tonnage of 3 Bt.CITATION:Fowers, C, Kepert, D, Absalom, M and Nitschke, N, 2013. Discovery, geology and structural setting of the Nyidinghu iron ore deposit, Hamersley Province, Western Australia, in Proceedings Iron Ore 2013 , pp 81-90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By W Liu, S Gao, D Wei, B Cui, Z Guan, Y Shen

Beneficiation of low-grade fine-grained hematite ores becomes increasingly important due to rapid depletion of high quality iron ore resources. However, fine particles, especially ultra-fine particles, make efficient beneficiation of these ores more difficult. Therefore, methods to reduce the influence of fine particles must be considered to achieve better beneficiation performance. Analysis and systematical beneficiation tests were carried out on an ultra-fine-grained hematite ore slime from washing a fine grained hematite ore. Ore particles were found to be presented in loose soil. While some of the ore particles were agglomerated, they were very fine and contained up to 76.5 per cent -0.023 mm material. In this paper, using a single magnetic separation flow sheet with sodium silicate (SS) as a dispersing agent, a concentrate containing 65.05 per cent Fe was obtained at an iron recovery of 68.58 per cent from the hematite ore slime of 56.65 per cent Fe. The single magnetic separation flow sheet was simple and reliable, the agent SS was effective in dispersing ultra-fine particles. The results are believed to be applicable to similar hematite ores.CITATION:Wei, D, Guan, Z, Gao, S, Liu, W, Shen, Y and Cui, B, 2013. Beneficiation study of an ultra-fine-grained hematite ore slime, in Proceedings Iron Ore 2013 , pp 495-500 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By B Murphy, A Uliana, P STrgio de Oliveira, G Ara·jo de Souza Franco, T Miettinen

Outotec has performed numerous research and development projects and various surveys in the study of reverse iron ore flotation. Over the past four years their TankCell-70 and TankCell-160 flotation cells at the Germano concentrator of Samarco in Brazil were extensively surveyed. These surveys have revealed some extreme operating conditions in reverse iron ore flotation and are the subject of this paper. Some of the findings include large variations in the content of solids in the various flotation stages. At the bottom of the cleaner cells, the content of solids by weight reached over 60 per cent, whereas at the bottom of the scavenger cell this was less than 50 per cent. Froth carry rates were also significantly different in the various flotation stages. In the case of coarse material, the scavenger cells operated at a froth carry rate of over 40 t/h.m2. With fine material, however, froth carry rates of less than 10 t/h.m2 were measured. High froth carry rates caused significant changes in the residence times at Samarco. In the rougher cells, the fifth cell had more than double the residence time of the first cell. This was even more pronounced with the scavenger cells, where the second cell had more than triple the residence time of the first cell. High froth carry rates also caused losses in iron recovery. As a consequence of such findings, it appears that different rules apply in the sizing of reverse flotation circuits compared to direct flotation circuits. Different operating parameters (mixing intensities and air flow rates) must also be used in the rougher, cleaner and scavenger cells in order to optimise the metallurgical performance. Outotec has also been working on a number of new technologies aimed at improving the metallurgical performance of iron ore reverse flotation circuits by increasing froth carry rate and decreasing fine iron entrainment.CITATION:Miettinen, T, Uliana, A, Ara·jo de Souza Franco, G, STrgio de Oliveira, P and Murphy, B, 2013. TankCell flotation at SamarcoÆs Germano concentrators, in Proceedings Iron Ore 2013 , pp 441-444 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By B M. Washington, R R. Lovel, G J. Sparrow, M J. Fisher-White

"Work in CSIRO with several Australian ores has shown that?by heating a high-phosphorus goethitic iron ore and then leaching with caustic or acid, the phosphorus levels in the ore can be lowered to a commercially acceptable value of around 0.08 weight per cent phosphorus (P). With increasing heating temperatures up to 1300¦C, the extent of phosphorus removal increased. This is considered to be associated with mineralogical changes in the iron oxide phases in the ore during the heating.Little phosphorus was removed from four high-phosphorus goethitic iron ores containing 0.12 - 0.16 weight per cent P in leaches with boiling water. However, leaches with sulfuric acid removed ten to 20 weight per cent of the phosphorus and leaching with sodium hydroxide removed even more phosphorus to produce leach products containing between 0.08 and 0.12 weight per cent P from three of the ores.After heating at 300¦C, leaches at a low pulp density of 0.5 weight per cent solids with 1 - 5 M NaOH and 0.1 - 1 M H2SO4 gave leach products with 0.06 - 0.09 weight per cent P. The lixiviant concentration required and extent of phosphorus removal depended on the ore. At a higher pulp density of 25 weight per cent solids, leach residues with between 0.07 - 0.14 weight per cent P were obtained.More phosphorus was removed from ores heated at 900¦C. Leaches at both the low and high pulp densities, with 1 - 5 M NaOH and 0.1 - 1 M H2SO4, gave leach products with 0.05 - 0.09 weight per cent P. However, the lowest phosphorus levels were obtained after heating the ores at 1200 or 1300¦C and leaching with 1 M NaOH or 0.1 M H2SO4. Leach residues with 0.02 - 0.06 weight per cent P were obtained, even from leaches at the higher pulp density of 25 weight per cent solids. Leaching tests on heated samples under heap leaching conditions at ambient temperatures have shown that phosphorus levels can be reduced to similar levels to that achieved in an agitation leach within ten days.CITATION:Fisher-White, M J, Lovel, R R, Sparrow, G J and Washington, B M, 2013. Effect of temperature on removal of phosphorus from Australian Goethitic iron ores, in Proceedings Iron Ore 2013, pp 373-380 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By D Connelly

There is now a new generation of mobile crushing and screening plant systems available which have been developed based on the motivation of reducing truck haulage. Newly designed mobile crushing and screening plant systems have the advantages of mobility, flexibility, economy and reliable performance, making this system very appealing for small- to medium-sized projects or projects where a number of resources are separated by distance.A brief review of the past history and experience with transportable crushing plants provides an insight into some of the issues with transportable plants in mineral processing. A closer look at a simple model based on exploiting small but high-grade orebodies suggests the concept has merit, however there are many more engineering, logistics, legal, technical and management aspects which have limited the application of such a concept in the resource sector. This paper explores the concept in detail and endeavours to analyse the preferred commodities and scenarios under which the concept could be used and the economic and logistical limitations for iron ore. The paper also looks at the risk assessment criteria to be applied in selecting the type of resource projects where the model could be applied successfully. Other aspects considered in this paper are the project planning requirements, technical and economic feasibility, bankability and operability. Reference is made to the operating experience of contractors at a number of sites and feedback from the resource companies as managers of the projects.CITATION:Connelly, D, 2013. Mobile crushing and screening plant applications for small- to medium-sized iron ore projects, in Proceedings Iron Ore 20 13, pp 349-354 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By C De-Vitry

"The large Yandi channel iron deposit (CID) is located in the north-west of Western Australia and is currently mined via open pit methods. Drilling at Yandi is widely spaced and current estimates are mostly linear averages of the surrounding local samples. Linear estimates such as ordinary kriging (OK) based on block sizes that are significantly smaller than the dimensions of the drilling grid are less variable than the unknown reality (Armstrong and Champigny, 1989).Conditional simulation (CS) provides a series of plausible realisations that represent the actual grade variability at a small scale (eg 1 m + 1 m + 1 m). These simulations are very useful for a number of purposes, eg: optimising grade control, stockpiling and blending selection of optimal drill hole spacing assessing resource risk on contained tonnage and metal.At Yandi the major constituents of the ore (Fe, P2O5, SiO2, Al2O3 and LOI) are correlated to varying degrees. Independent CS of each assay variable will not reproduce these correlations. Reproducing the correlations (and the shape of scatterplots) is important if the simulations are used for the abovementioned purposes. This paper examines and compares various methods of CS that aim to reproduce the correlations between the assay variables.The CS methods evaluated in this paper are conditional co-simulation (CCS) using the linear model of co-regionalisation and two other, alternative multivariate simulation methods, which use min/max autocorrelation factors (MAF) or the stepwise conditional transform (SCT) to de-correlate assay variables before performing independent CS. It was found that CCS best reproduced the characteristics (histograms, variogram, scatterplots, etc) of the declustered drill hole data (Figure 1). Whilst simulation using MAF generally produced acceptable results, the method did not adequately reproduce the variance of the assay variables. The univariate statistics, histograms and experimental variograms were acceptable for simulations generated from the SCT. Bivariate statistics, cross-variograms and scatterplot reproduction for the SCT were unacceptable. The latter method produced inferior results because there were insufficient samples to obtain a reliable transform of the third assay variable in the transformation sequence.None of the abovementioned simulation methods provides good reproduction of all the scatterplots. This is due to the presence of clay pods, which cause some scatterplots to display two trends. These clay pods contain higher percentages of SiO2 and Al2O3 than the surrounding CID. The clay pods are generally smaller than the drill-grid dimensions. Thus their locations are typically unknown and they cannot be defined by manual interpretation, eg via wireframes. The locations of the clay pods were simulated via indicator CS. CCS was then performed separately for the clay pods and the CID. This significantly improved the reproduction of the correlation coefficients, the scatterplots and visually the simulation was more geologically realistic. Simulating the location of clay pods followed by CCS of assay variables is the recommended approach for simulation at the Yandi CID.CITATION:De-Vitry, C, 2013. Simulation of correlated assay variables - a case study from the Yandi Channel iron deposit, in Proceedings Iron Ore 2013, pp 137-148 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013