Search Documents

By M. Uszko

The climatic area in which Poland is located requires heating the ventilation air at intake shafts during the winter season. Air heating of the intake shaft should ensure safe operation of hoisting devices; while at the same time it also affects the conditions of the mine environment. The paper presents the issues of shaft heating in coal mines in terms of the mining law, the effect on the conditions of the mine environment and heating technology solutions used in the mines of Kompania Weglowa S.A. (KWSA).

Aug 1, 2013

By Martin Grenon

This paper presents two case studies where fracture set orientation was quantified using three methods: a simple fracture pole grouping, a Fisher distribution and a Kent distribution. The three fracture orientation representations were then used as inputs for kinematic slope stability analysis. Differences showed up in the probability of sliding for all instability modes considered.

Aug 1, 2013

By K. Tarr

Acid-producing mine tailings are present at many active and inactive mine sites and pose an environmental liability due to the potential for acid rock drainage. Acid rock drainage originating from a tailings pile, a waste rock pile, or exposed sulfide-rich rock, can cause discoloration and turbidity in receiving waters, and the loading of ions mobilized by the acid can cause a decrease in aquatic flora and fauna, and reduction in the quality of groundwater. The primary cause of acid generation is the oxidation of sulfide minerals, predominantly pyrite and pyrrhotite. Considerable mine tailings are being stored on surface in vast tailings impoundment areas across Canada. In the tailings within this study, from the Sudbury, Ontario area, the sulfide mineral of primary concern with respect to acid generation is pyrrhotite. Different tailings types show varying and progressive degrees of oxidation correlating to their specific sulfur contents. The degree of oxidation is determined by the relative extent to which the sulfides have reacted as well as the depth of oxidation within the tailings. Natural Resources Canada, CanmetMINING is dedicated to research supporting the Green Mining Initiative, a program reducing business risks by demonstrating practices that reduce environmental impacts. In cooperation with the Canada Mining Innovation Council (CMIC), applied research aims to reduce land disturbance, waste volumes, and releases to the environment. By reutilizing tailings from vast impoundment areas as a component in backfill, the potential environmental impact would be lessened considerably, due to the reduced tonnage stored on surface long-term. From an operating perspective, there is a need for supplemental feed for backfill from time to time. The reclamation of old tailings for use in backfill is also driven by the fact that old tailings ponds may not be structurally stable, and it may be more cost effective to remove the tailings than to upgrade the impoundment structure. However it is imperative that these old tailings be fully characterized to determine their suitability for use underground, in order to ensure the long-term integrity of the resulting backfill matrix. A study was conducted to investigate the feasibility of tailings reclamation from old impoundment areas as a significant component in backfill. The materials were first physically and chemically characterized, followed by preparation of samples to determine optimal mix proportions for strength development for both paste and hydraulic fill compliance. It was found that the amount of oxidized tailings included in the backfill material had a profound effect on both the segregation and settling properties of the backfill matrix, as well as the mechanical properties of the samples. The strategies for decision-making, based on the criteria for material characterization, mining plan, and cost effectiveness are discussed.

Aug 1, 2013

By Zoë Mullard

Just as a mine has a lifecycle, employees working within the mining sector also make several transitions throughout their career, from initial recruitment to retirement from the industry. Throughout the employment lifecycle, employees bring skills and knowledge that significantly contribute to the global economy. These skills are developed through education, professional training, coaching and through hands-on experience. Despite the current economic conditions and the demand for minerals, the mining industry is facing a substantial skills shortage due to the disparity between the number of new workers entering the mining industry and a largely ?graying workforce?. Although educational programs continue to evolve to attract people with a wide range of skills, the diversity of jobs and the strains of working in remote mining operations continue to present challenges for recruitment and retention of employees. This gap also presents challenges around knowledge transfer at a corporate and mine-site level; employers will require cultural and techno-sociological approaches to ease through these transitions. At the same time, there has been an explosion of social media tools that facilitate information sharing, cross-organizational collaboration, distance learning and knowledge capture. These tools have become increasingly popular in the last few years and their applications vary widely. The mining sector has started to adopt these tools for a number of purposes, including opportunities to harness social media to enhance human resources interactions, outreach and oversight. This paper will outline several case studies that explore leading practices for how the application of new media can assist organizations and individuals as they progress through their careers. This paper will illustrate how new social media communication technologies can be used to increase employee engagement and build organizational capacity in the mining industry. The paper will also include strategies for how to implement social media to enhance human resources applications and will cover ideas for monitoring and evaluation.

Aug 1, 2013

By Cheng-Ting Chiang

Information integration and exchange for the entire building life cycle is one of the most important issues in the AEC industry. Although the Building Information Model (BIM) technology is widely utilized to address them, BIM is mainly concerned within the design and construction (D&C) phases. In the operation and maintenance (O&M) phases, however, the information integration and exchange issue becomes more complicated because software applications here require not only BIM but other information outside of the AEC domain, e.g., disaster mitigation. Nowadays, most BIM-related research focuses on the D&C phases and pays less concern on the O&M phases, hence there is a research need that can help seamlessly transfer the information between the D&C and O&M phases. In this research, a software framework using ontology was designed to deal with aforementioned problems. The BIM data from the D&C phases were used as a foundation to generate new models for different software applications for the O&M phases. The ontology technique was employed to assist the model transformation process between the original BIM and the models for applications. Finally, a disaster mitigation example was chosen to validate the framework, in order to make sure that the transformation process is comprehensive and useful from domain experts? perspective.

Aug 1, 2013

By E. Onal

Mining operators are faced with complex information delivered by technology-centric rather than user-centric systems. The ability to achieve high situation awareness (SA) in the face of this data overload is a key challenge for effective decision making and information exploitation. Incidents that result in loss of revenue and even life, and compromise safety that are attributed to human error are often the result of system designs that overload human cognitive capabilities. This paper focuses on defining SA as it relates to mining operations and presents methods for improving SA through a scientific approach for electric shovel operator user interface development.

Aug 1, 2013

By Yu-Min Cheng

Over the past two years, the construction industry has increasingly recognized the benefits and capabilities of building information modeling (BIM) for information integration, visualization and parametric design, reducing the duplication of work and complexity of interface integration, while significantly saving both time and cost. However, due to the variety of participants in engineering projects, the differences between data definition, data format, and data storage increase the difficulty of integrating data from diverse sources. Therefore, buildingSMART has developed a common data schema, called Industry Foundation Classes (IFC), that makes it possible to hold and exchange relevant data between different software applications, to increase the efficiency of BIM work and to ensure a consistent and high-quality output. This paper presents a novel methodology that assists in facilitating the import and export process for parametric BIM objects between heterogeneous BIM systems. This methodology is based on the IFC data schema and includes graphical and non-graphical description data. The objective is to retain the geometry, parameters, unit, texture and links of an object during exchange and sharing to ensure that data integrity is maintained. To sum up, this research addresses the issues of transferring parametric BIM objects between heterogeneous systems to increase data integrity and reduce transfer and integration times.

Aug 1, 2013

By V. K. Srivastava1

Coal mine fires burn about 20?21 million tons of coal per year throughout the world, which not only results in loss of valuable coal reserves, but also cause serious environmental hazards over large areas. The famous Jharia Coalfield of Dhanbad, India is no exception; here a coal mine fire originally reported nearly a century ago is still continuing unabated in vast areas of the coalfield. In this paper, an attempt has been made to analyse high resolution multispectral thermal images of ASTER for mapping and delineating surface and subsurface coal mine fire areas of this coalfield. From the generated temperature gradient map, as well as from the surface temperature anomaly map, it has been possible to differentiate shallow and deep coal mine fire regions and other erroneous cultural features. It is observed that the coal fires are distributed mostly in the eastern part of the area, which has branched into two major coal fire zones: one along Lodna- Tisra-Bhulanbarari-Kujama-Jealgora Jharia and the other along the Kusunda-Kendudih area. The western fire zone is restricted in Dumra-Nadkhurkee-Jayramdih area. From ASTER thermal infrared data from 2006, the total affected area is estimated to be about 7 km2, of which the deep subsurface coal mine fire area is around 3 km2 and the shallow surface coal mine fire area is around 4 km2, as compared to 18 km2 coal mine fire area estimated in 1987 using Landsat TM thermal band data. In other words, the fireaffected region has decreased by about 50 % during the last 18 years. However, such decrease in coal fire area is seen in the central portion only, and has in fact increased in the south eastern parts of the Jharia coalfield. Study of Differential Interferometery images, generated from Earth Resources Satellite (ERS) synthetic aperture radar (SAR) tandem data has shown that the active coal mine fires are in general associated with low topography/subsidence areas.

Aug 1, 2013

By M. J. A. Ruszala

Aggregates production is a huge global industry which uses an enormous amount of energy and produces a massive amount of unsalable fines. Reducing the amount of energy used per tonne of product and/or the amount of fines produced, would make a quarry more efficient. This reduction would make the quarry more environmentally friendly and profitable. This research looks at modelling Mountsorrel Quarry, a granite quarry in the United Kingdom (UK), using JKSimMet and Split-Desktop software packages in conjunction with the European Union (EU) project, EE-Quarry. Samples submitted to drop weight tests confirmed Mountsorrel Quarry granite as an extremely hard granite. Rock fracture data (t10) and energy of comminution (ECS) data were obtained from analysing the results. Split-Desktop image analysis software was utilized to determine the particle size distribution (PSD) of the primary crusher feed, as it contains particles too large to screen manually. It was also found that <1% of the feed is fines, which at Mountsorrel Quarry are classed as particles smaller than 5 mm, and that no particles were larger than 3,810 mm. JKSimMet was used to create a flowsheet of Mountsorrel Quarry. The crusher product PSDs were simulated and found to have strong correlations with experimental data, calculated by screening samples from conveyor belts, especially in the fines region, with a mean difference of 1%. The simulated primary crusher product PSD showed that it contains ~6% fines. A simulation over the entire quarry showed the product to be within the size range produced at Mountsorrel Quarry, and with a simulated fines content of 13%. When the CSS on the primary crusher was altered from 165.1 mm (the operating size on site) to 100.0 mm, it increased the overall percentage of fines produced by 3%, increased the power draw by 140.6 kW, but reduced the overall plant production percentage of fines by 2%. Two blasts were analysed on adjacent rock faces. They had identical blast designs, but the order of deck detonation varied; the first blast detonated the bottom deck before the top and vice versa in the second blast. For each blast, measurements of the feed PSD to the primary crusher, the number of particles that required secondary breakage on the quarry floor, acoustic levels and vibration readings were measured. No significant difference was identified between the two blasts in any of the parameters measured. In conclusion, a working model of Mountsorrel Quarry has been made in JKSimMet that has been validated against data from site and Split-Desktop has been used to simulate the primary crusher feed PSD, something that was previously unknown. The effect of reversing the order of deck detonation in a two deck blast was also analysed but with no significant difference between the two blasts found.

Aug 1, 2013

About MAC ? The national organization of the Canadian mining industry ? Mining, smelting and refining of base and precious metals ? Mining of iron ore, diamonds, uranium, oil sands, coal and industrial minerals ? Many associate members ? www.mining.ca

Aug 1, 2013

By Mohammed Sakr

The empirical relationship between torque measured during installation and pile capacity has gained a wide acceptance in the helical pile industry in the last few decades. This paper presents a theoretical model developed to estimate torsional resistance of cohesive soils to helical pile installation. The proposed torsional resistance model was then used to establish torque factor, Kt, a factor that is widely used in the industry. The results of the study indicated that the Kt factor is a function of the load path (i.e. tension or compression), pile geometry and soil properties. The assessed Kt factors in tension and compression were validated by the results of 74 installation records and full-scale helical pile load tests. A parametric study was also performed to qualitatively assess the relative importance of different parameters that affect the Kt factors.

Aug 1, 2013

By A. Kozlowski

We present research on cable fault location methods for mines where coal dust and methane explosions are a frequent potential hazard. The methodology and devices for low- and medium voltage cables fault location are well known and applied in classical power distribution networks. They are based on solutions for underground mines with a high risk of explosion. The lack of a safe solution for the location of a fault has contributed to the initiation of a research project by a group of Polish companies. The consortium consists of research institutes (Institute of Innovative Technologies EMAG, Tele and Radio Research Institute, Central Mining Institute GIG-KD ?Barbara?), Silesian University of Technology and a private entrepreneur MARTECH PLUS. Fast and exact determination of fault location is one of the important factors for minimizing power outage time. The lack of technical solutions to obtain measurements in a secure way leads to the use of the methods connected with a high risk of explosion. For example, the application of high energy can lead to arc discharge where there is a fault in insulation, creating the risk of an explosion. Measurements of methane concentration along the analyzed section of the cable reduce the risk; however the shock wave generated by the electric arc may raise coal dust and make an explosive mixture, which is an object of ignition. Low energy methods, like those based on reflection waves, have low sensitivity for high- and medium-resistance faults. This technique has difficulties in joints, which create false echoes. The fundamental problem is to determine the topology of the network using a reflectogram and find anomalies of a different nature ? not only open and short circuit. Included in the scope of the project is an analysis of Polish legal regulations related to fault location and operational work for low- and medium-voltage networks. Two of the methods used on the surface were selected as feasible to implement under explosion hazard conditions. In the process of development of the fault location methodology, installation features characteristic of underground mines were used, namely access to the whole length of a cable. This is the attribute that provides an opportunity to do measurements that are usually not possible for typical surface power nets. To carry out laboratory tests, a dedicated measuring stand with various types of cables was built. The authors describe the principle of operation of the fault locator and the results of the laboratory tests carried out on the cables with built-in damage (prepared for tests). Results of the work will be the basis for the next stage of the project associated with operational analyses of the prototype.

Aug 1, 2013

By A. L. Karyakin

The report focuses on the process measurements of the mass of rock in the bucket power shovels and dragline excavators. The mathematical models are suggested of AC and DC electric drives of excavators. These models are a basis for calculation methods of the electric drive electromagnetic torque. The design schemes of mechanical equipment of excavators considered to account the situation of bucket in the plane of the boom. The methods of static moment allocation and identification of the excavator technological operations are developed. The results of the work are experimentally tested on power shovels with bucket capacity of 12 and 18 m3.

Aug 1, 2013

By Jianzhong Liu

Based on the characteristics of overburden rock strata movement, surface ground subsidence and casing deformation and failure, a tension-shear combination failure model of surface borehole was set up. The main controlling factors of the mining-induced deformation and failure of surface borehole were researched with this failure model and the limit analysis method. The mining methods and geology conditions mechanics action mechanism to surface borehole and its time ?space evaluation rule was found. The surface borehole deformation and fracture rule were advanced. It provides theoretical support to optimizing layout, structure type, security measure and local casing protection of surface borehole.

Aug 1, 2013

By F. Q. Su

Underground Coal Gasification (UCG) is a promising environmentally acceptable clean-coal technology. A typical UCG system has two wells drilled from the surface into a coal seam with some separation of injection from production. The wells are connected underground by various linking techniques. After creating a combustion reactor in an underground coal seam, air and oxygen flow through the injection well. Heat energy and gases are collected from the production well. As gasification progresses, the combustion reactor is moved along the linking hole. Using this process, the fracturing activity inside the coal seam serves an important role for enlargement of the gasification zone because the surface area oxidization increases continuously by coal cracking. For effective coal gasification, fracturing activity must be controlled. Moreover, excess fractures inside the coal seam and surrounding rock can induce gas leakage, underground water contamination, subsidence, etc. Therefore, monitoring and control of fracturing activity in underground areas constitute key technologies for efficient and safe UCG. To monitor fracturing activity, we conducted laboratory and small-scale field experiments of UCG using acoustic emission (AE) measurements. UCG model tests were conducted for linking and coaxial types UCG models. Coaxial UCG systems are compact and are anticipated for application in underground coal seams having a complex geological structure. The UCG model consists of a coal block molded in a steel canister (20 liter capacity) with heat-resistant mortar, with a linking hole or a coaxial-hole passing through the coal block. During coal combustion, coal temperatures, production gas contents, and AE activity were monitored under the control of injection-air and oxygen flow rates. Results show that the combustion propagated inside the specimen along the linking hole. Many AE events were generated during coal combustion. The AE activity was related closely to temperature changes inside the coal block. This AE generation apparently results from crack initiation and extension around the coal combustion area under the influence of thermal stress. However, comparing the results from UCG models of linking and coaxial types, the gasification of the linking type model showed an average calorific value as high as 11.3 MJ/m3. The coaxial type yielded an average calorific value of produced gas as only 5.79 MJ/m3. In the coaxial type of UCG model, the combustion region was limited to the area around the coaxial hole. The AE activity was lower than in the linking type model. For small-scale UCG field experiments, linking and coaxial types were tested at an open pit coal mine in Hokkaido, Japan. Using a linking type UCG, 58.2 kg coal was processed in 39 h, with the calorific value estimated as 11 MJ/m3. However, the coaxial type UCG processed 7.0 kg coal in 9 h, yielding an estimated calorific value of 6.0 MJ/m3. These tendencies resemble those of results of laboratory UCG experiments. Results of these experiments demonstrate that AE monitoring is a useful tool to evaluate combustion reactors for efficient and safe UCG systems. To develop a coaxial UCG system, results show that fracture control around combustion reactors is indispensable.

Aug 1, 2013

By D. C. Reid

This paper describes the latest results in research and development currently being undertaken by the CSIRO Mining Technology Group to advance the automation capability of continuous mining equipment in underground coal mining operations. This research delivers enabling technologies that are essential in achieving increased roadway development rates as well as providing a safer working environment for underground mine personnel. Details are presented on technical developments and results of large-scale above-ground experiments conducted under field-realistic conditions. These experiments demonstrate the performance of the ?self-steering? capability which will enable a continuous miner (CM) to automatically maintain a given mining heading and mining horizon under production conditions. A primary technical requirement of this automated functionality is the means to accurately determine both the location and orientation of the CM in real-time. Test results of a high performance navigation system utilising vehicle motion aiding technologies are presented. This system combines high performance inertial sensors, and custom-developed radar to achieve a navigation-grade guidance system. Comprehensive performance evaluation has been conducted using a scale skid-steer mobility platform operating autonomously through a typical roadway development mining pattern with a total path length of 2700 m and mission duration of 112 min. Results from this evaluation demonstrate that the sustained accuracy of the navigation system exceeds the original project expectations and is well suited to the requirements for this underground mining application. There are presently no known alternative methods for providing a practical and accurate three-dimensional guidance solution in this application. This achievement represents a significant milestone in delivering a step change improvement in underground coal mining roadway development.

Aug 1, 2013

By Zhen Lei

In Alberta, Canada, heavy industrial projects are constructed using a prefabrication approach: spools and pipes are produced in the factory, and are assembled into modules that are transported to the industrial plants for installation by mobile cranes. Planning the onsite mobile crane operations is critical to the project budget and schedule. However, due to the large magnitude of industrial projects, manual heavy lift planning is tedious, and the results are not particularly responsive to site changes. This paper introduces an integrated mobile crane management system developed by PCL Industrial Management Inc., in collaboration with the University of Alberta, which investigates crane location selection and path checking for field module assembly. The project information is stored in a database, and the proposed system retrieves data, performs the calculations, and records the results back to the database; the calculations involve automatically selecting locations for the mobile crane, considering the crane capacity, lifting range and utilization. Lift paths for modules are checked for feasibility based on selected locations, satisfying the site and crane configuration constraints, and crane walking paths are planned if needed. The designed system is tested in an industrial project to validate the effectiveness of the system.

Aug 1, 2013

By E. G. Baltuch

Natural Ventilation in mining and metallurgical processing applications is key to proper operation function. There are number of ventilator designs available to a project team or design engineers, the selection of which will affect both the type of building structure required, project costs and design performance which is difficult to rectify or re-engineer once implemented. Research and applied results, such as that performed by Air-Therm Inc., demonstrates that computational fluid dynamic simulation allows for 5 dimensional observation, analysis and optimization at significantly lowered cost than previously possible. These results have been fully implemented on a number of mining and metallurgical applications and the company continues to study, optimize and innovate as new tools become available to provide the best possible engineered solutions for particular applications.

Aug 1, 2013

By M. S. Ünal

Creation of 3D model of coal seams is a tedious and time consuming operation. Computer aided 3D solid modelling of coal seams can be performed in a fast and detailed manner. However, in case of having tectonically disturbed coal seams where faults may be observed, expert opinion is necessary to decide the geometry of the coal seam. The aim of this study is detection of fault zones with computers by using drill hole data. Firstly, a digital database is generated by using the drill hole data. Surface models of the layers are produced by applying triangulation method on coal seam roof elevations. The generated surface is divided into small squares and consequently dip and dip direction values are calculated for each square. Variograms for dip and dip direction are determined and maps showing the variation of dip and dip direction are generated by using geostatistical methods such as kriging and co-kriging. Examination of disconformities observed on estimation maps created by kriging and co-kriging clearly reveals the extension of faults. The method used in this study is applied to detect fault lines of a known mine field. 3D solid modelling of the coal seam has also been performed by using conventional cross-section method. The results of both methods were in good agreement. Identification of major faults by using the method introduced in this study could certainly simplify 3D solid modelling of coal seams.

Aug 1, 2013

By W. J. Kempson

In recent years, substantial progress has been made with respect to the definition and control of the primary energy requirements in underground mines. Little has, however been done to develop a more detailed understanding of how to limit the various pressure losses which are intrinsic to shaft systems. This is in spite of the fact that more than half of the pressures generated by the ventilation fans in deep level mines are dissipated as pressure losses within the shaft system. This paper presents research which has been completed to optimise the pressure losses which occur in shaft systems as a result of the ventilation air flowing through them. In this regard, the response of various shafts to the ventilation air flowing through them was measured. These results were evaluated against the current theory for the calculation of shaft pressure losses. Finally the results of the measurements and calculations were used to calibrate a Computational Fluid Dynamics model of the shaft systems. This model was then iterated to allow meaningful conclusions as to the specific make up of the shaft equipment which contributes the most to pressure losses in shaft The results of the above analysis demonstrated that the current theory used for the evaluation of these pressure losses is deficient. The paper discusses these conclusions and the specific ramifications of the analysis. Finally, the understandings gained with regards to the above research are applied to the design and layout of equipment in mine shafts. In this regard, the shape and orientation of the shaft steelwork is evaluated and it specific interaction with the piping and conveyance is evaluated. Coming out of this evaluation are specific recommendations for the design of future shaft systems. These recommendations are based on the above models and offer specific savings on the lifetime operating costs of shaft systems.

Aug 1, 2013