Search Documents

By H. L. Riley, B. W. Gandrud

AS far as the present writers know, this system of flotation has not been used elsewhere in this country, but in the last couple of years it has been introduced, with minor variations, at one plant in England and one in Wales.' The system has been described and discussed in a number of publications.2-5 The following is quoted from an abstract of the latest of these,5 a paper presented at an International Conference on Industrial Combustion in 1952. On the basis of experience to date with the commercial plants, it is believed that the kerosene-flotation process incorporates all the necessary elements to make it greatly superior to anything else now available for treating of fines in wet processes of coal preparation. Additional study and investigation are still needed, however, to determine if certain phases of the process can be improved to such an extent as to make it generally satisfactory and acceptable to the industry. Further improvements will be needed with respect to the capacities of the flotation cells and the reagent consumption. The situation referred to above explains why an investigation is being made of the possibilities of achieving better cell capacities. Results obtained from this investigation, which is still in progress, are believed significant with regard to both cell capacity in general and the relation of cell design to cell capacity in particular. Commercial equipment now being used in a laboratory-type investigation should have performance characteristics similar to those of the larger machines. Equipment and Procedures: All flotation tests have been made in a standard Denver sub-A 24x24-in. unit cell of 12-cu ft volume. Cell modifications to make it more suitable for the tests were an adjustable front-wall section for varying cell depth and a perforated scraper-drag assembly for removal of the float product. There is also an apron dry-coal feeder, a gravity-feed water supply, reagent feeders, and a centrifugal pump that feeds the mixture of coal, water, and reagents into the flotation cell. A wattmeter connected into the drive-motor circuit records the power requirements of the impeller throughout each run. Dry coal, water, and reagents are all fed through a pan-type intake to the feed pump. A Sturtevant blower was set up to furnish air for supercharging. A centrifugal pump with a garbage-can intake provides for disposal of refuse flow to an outside settling tank. Figs. 1 and 2 show the flotation cell; Fig. 2 also illustrates the blower for supercharging. For purposes of this investigation, the percentage by weight of the feed coal recovered in the float product under a standard set of conditions has been considered as the criterion of cell capacity. The authors realize that such a criterion may be somewhat unorthodox, as the term cell capacity is usually understood to refer to feed input and ordinarily takes into account the ash analyses of the float product and refuse. However, the word capacity is flexible enough so that Webster gives one definition as maximum output, a definition which seems to justify, at least partly, acceptance of the above criterion. It has been the authors' experience in the Birmingham district that the ash-reduction efficiency of the coal-flotation process is generally satisfactory and that the only real problem is to increase the rate of float recovery so that the feed rate to any given bank of cells can be increased without undue loss of coal in the refuse. Originally it was planned to operate the flotation cell to simulate continuous operation during sampling periods. It was assumed that operating for reasonable time with feed coal, water, and reagents turned on would stabilize conditions so that the weight of float coal discharged during a fixed time interval would be an accurate measure of the rate at which the coal was being floated. It developed, however, that this supposition was erroneous. The float coal, caught for fixed time intervals and weighed, gave widely varying results in duplicate runs. Efforts to correct this trouble failed, and it was decided to try to operate on a batch-test basis, whereby all the float coal produced during a run on a known weight of feed coal would be caught in tubs, dewatered, and weighed. This method gives consistent and reproducible results, with total float product weight rarely varying by more than 3 or 4 pct on duplicate runs. The standard test procedure is as follows: A 132-lb sample of dry feed coal is weighed and placed in the feed hopper. The feeder is adjusted for a rate of 800 lb per hr. Feed water and reagents are turned on, and the feed and refuse pumps are started. One minute later the impeller is started. Six minutes are allowed for the cell to fill up with the water-reagent mixture. The feed of dry coal is started at the end of this 6-min period. One minute later the float-coal removal drag is started. The float coal is caught in one tub for the first 6 min after the flow of feed coal starts. Tubs are then changed, and the float coal is caught in a second tub until the feed coal runs out, when the tubs are again interchanged to catch the float coal for the remainder of the run in the first tub. The cell is kept running for 3 min with the water and reagents on after the feed stops to allow residual float coal to be removed. At the end of a test the wet float coal in both tubs is weighed and the total weight recorded. The product in the second tub is used for moisture determination and screen-size analyses. When the

Jan 1, 1956

By E. P. Bucklen

Simulation is a tool useful in the evaluation of the probable effect which various changes may have on the performance of time-dependent systems. This is especially true as far as rail transportation in mining is concerned. The VPI-OCR RAILSIM program is a computer program designed specifically for solving a broad range of problems encountered in the design of haulage systems of new mines as well as in the operation of haulage systems in existing mines. This program is one of several computer applications for evaluating mining systems developed at the Virginia Polytechnic Institute and State University under contract with the Office o f Coal Research of the U.S. Dept. of the Interior. The RAILSIM program uses Monte Carlo techniques to introduce variability in the occurrence of events such as would be observed in real systems. Data are required to describe the haulage network, locomotives, stationary facilities, and other miscellaneous parameters. Output from the program lists measures of performance that are useful in assessing the capabilities and limitations of given system configurations. The output information may cover many shifts of operation to indicate the broad range of variation and interaction which can occur as the system responds to varying levels of demand for service. The RAILSIM program was tested extensively in mining operations. The results of some of these tests are used to illustrate the usefulness of this program.

Jan 1, 1972

By C. W. Kempton

IF New England were located in some distant and almost inaccessible region, there is no doubt that its mineral resources would have been ere this well developed and generally acknowledged, but laboring under the disadvantage of nearness, it has been neglected. Its surface, moreover, is not cut up by mountains and canons, and the remnants of many of the old ridges are extensively covered by glacial drift. Having for the past ten months been engaged in the development of a. mineral district in Southeastern Maine, I would take this opportunity to lay before the Institute sketches of results, and try to give some idea of the formations as found. The Sullivan Mining District extends from the town of Franklin, through Hancock, Sullivan, and Gouldsborough, from northwest to southeast, about sixteen miles. A general idea of this locality may be gathered from the map accompanying. (Fig. 1).

Jan 1, 1879

By SAMUEL GOMPERS

THE name engineer makes a very strong appeal to one who appreciates the mechanism underlying the fabric of our civilization. Engineers are scouts of civilization. We send them ahead into the lone 'places-the wilderness, the jungles, the great watery expanses, to build the highways necessary for civilized man. The engineers must deal with Nature, with that mysterious dynamic thing we call "force," with materials. It is their function to direct the human activity necessary to coordinate these forces and material in order to make them serve the needs and aspirations of men. Because of my high conception of the engineering profession I was glad to accept the invitation to address The American Society of Mechanical Engineers to voice my understanding of the possibilities of your work as engineers of industry, and to suggest what seems to me the responsibility of the-engineer to the whole modern industrial system.

Jan 1, 1921

By Fred D. DeVaney

W. O. Philbrook (Carnegie Institute of Technology, Phila.)—Mr. DeVaney's paper is a valuable addition to the growing technology of the magnetic roasting of lean iron ores. His furnace is ingeniously designed to permit close control of the process and to achieve high thermal efficiency by counter-current heat exchange and the withdrawal of both solid and gaseous products at relatively low temperatures. The principle of using a lean reducing gas to avoid over-reduction of the ore even at high operating temperatures (for rapid re-action rate) is thoroughly sound. The gas analyses and flow rates reported, however, are internally incon- sistent and render suspect any details of a heat balance based upon them. While it is entirely proper to consider the entrant gas as a reagent and to account only for the heat evolved by consuming a portion of the gas, many operators are accustomed to a heat balance using the total calorific value of the reagent supplied; and comparison of heat balances made with different bases of calculation can be quite misleading. Since Mr. DeVaney's paper is likely to be cited frequently in future discussions of magnetic roasting processes, it seems worth while to point out the internal discrepancies and to give alternate values of heat requirements for different bases of calculation.

Jan 1, 1954

By B. M. Larsen

NEVER having actually tried to engage in the systematic education of anyone, and having little direct knowledge of the practical problems and limitations in the field of education, I can pose only as a "nonexpert" in this field, one whose ideas are to be regarded as personal opinions. The necessity for compromise between educational ideals and the practical limitations of time, money, and mental capacities of both student and teacher is evident in the preparation of an end product that we may regard with a reasonable degree of conviction as a professional engineer. We need to do so many things. The engineering student must have a clear understanding of the basic sciences; he should develop manual skills and co-ordination; he should speak and write the language with simple clarity and directness; he should gather knowledge of a special field; and, he should be educated for living in a broad ..

Jan 1, 1948

By John F. Abel

A good mining engineer is supposed to make a good mine. What then makes a good mining engineer? There certainly are a lot of answers to that question. The answers depend on whether you are one, work for one, or employ one. There are several cliches about mining engineers, and there is some truth in them-as there usually is in any stereotype. Hollywood chose Jeff Chandler to portray a mining engineer in Foxfire. The image here was of an almost one-man mining operation. When Chandler picked up a jackhammer, cradled it in his gut and started drilling out a tunnel round, it gave one the hives. I would have liked to see him finish just one round that way. There are limits to what even the most hairy-chested of us will try. We can assume that Hollywood feels it needs to over- draw any profession to add impact.

Jan 1, 1970

G. SHERBURNE ROGERS,* Washington, D. C. (written discussion ?).- Mr. Neal's paper on the petroleum hydrology of the Mid-Continent district is a welcome contribution on a subject concerning which none too much is known; it is, I think, the first published description of the chemical character of the oil-field waters of the great Mid-Continent area. When studying the oil-field waters of the California fields several years ago, the differences in chemical composition between waters occurring at various horizons seemed to be sufficient to enable the operators to use water analyses as a basis for determining the source of the water flooding a well; and it is gratifying to find that, Mr. Neal has arrived at a similar conclusion. As Mr. Neal points out, the Mid-Continent waters are very different in character from those of the California fields, and casual. inspection

Jan 3, 1919

By C. C. Harris

The characteristics of some common size distribution equations are critically discussed. A generalized form of several well-known size distribution equations is obtained from a differential equation describing statistical distributions. The equation contains three parameters and can describe the major features of size distributions in the fine and the coarse size regions. A graphical method for its implementation is provided. The application of this and other equations to sets of data are compared both for the quality of fit and from a comminution kinetics viewpoint. If a narrow size range of a brittle material is broken sufficiently to obliterate the feed sizes, but not so severely that excessive secondary breakage occurs, a plot of cumulative fraction by weight undersize (Y) vs. sieve size (X) on a log log grid (sometimes called the Gates-Gaudin-Schuhmann plot)1-3 gives a straight line of slope ~ 1 over much of its range. On closer inspection, deviations in the extreme coarse range covering perhaps 10 to 30% of the total sample may be apparent (frequently, a change in slope from ~ 1 to a value different from unity) together with over-all slight irregular departures from a smooth line. One model of breakage postulates that the same fracture pattern persists throughout all size ranges.4 The fracture pattern is characterized by the slope of the line on a log log grid. Accordingly, a distribution of sizes broken in the manner specified earlier is expected to produce a size distribution having the same slope as that of a broken narrow size range. Additionally, the slight irregularities mentioned above should even out in the summation process, giving a smooth straight line of slope ~1 on a log log plot. This idealized state of affairs does not, however, describe the distribution of a multi-event process such as that for a tumbling mill product. On the average, these curves (plotted again log log) tend to have a slope in the fine region different from and usually less than unity,5 while the coarse size region curves with increasing slope for cases of mild reduction, and with decreasing slope when moderate or severe size reduction has occurred. In addition, there are usually slight irregular deviations from a smooth curve. Most curves display two distinct regions — fine and coarse — and a few curves show one or more intermediate regions. Feed size studies6,7 show an effect which theory is required to explain. For the same material, mill loading and other operating conditions, and the same time of grinding, plotting the dimensionless ratios Y vs. X/(feed size) does not reduce the size distribution data to the same curve. Y vs. X does not correlate the coarse region, but it can provide a crude correlation of the fine region which improves as size diminishes and as grinding time increases. The size distribution in the coarse region is somewhat more dependent on the feed size than is the distribution in the fine region wherein the degree of dependence diminishes as time proceeds; the distribution of sizes in the fine region are determined largely by the nature of the material and the comminution conditions. A comprehensive model of comminution must recognize that several different patterns or modes of breakage can occur in a mill; 5,8,9 that there can be some selection in that some size ranges are broken more than others; and that, while some particles may be the product of a single fracture event, or may even remain unbroken, others result from multiple rebreak-age. Thus, breakage in a tumbling mill is more complex than the Schuhmann4 model admits in that several different types of comminution micro-events* occur rather than just one type, and these events, though different in size scale, are of the same overall pattern as that which is visualized by the model. The concept of an average comminution micro-event has, therefore, a mathematical rather than a physical connotation, at least for tumbling milling. Equations with which to describe particle size distributions have been sought for over half a century.10-13 No equation presently in general use was first derived from an analysis of the statistical mechanics of breakage; whatever theoretical basis the existing

Jan 1, 1969

By L. D. Mullins, E. B. Elfrink, W. L. Wahl

In the past few years several articles and papers presenting results of solution gas-drive depletion calculations have appeared in the lit-erature. Such calculations are of interest to the oil industry, for investment decisions must often be made before much is known about a reservoir. At other times, an estimate of the possible benefits to be realized from alternate production methods is desirable, and theoretical depletion calculations can serve as a floor or reference level from which to work. In any case, an estimate of ultimate oil recovery based upon engineering data is commonly required. An engineer confronted with the problem of obtaining, for a specific reservoir system, an estimate of ultimate oil recovery by solution gas-drive depletion usually will be forced to perform the calculations himself. This is despite the quantity of data in the literature. Rarely will either experience or the literature provide results from a reservoir system similar in all important respects to the one under consideration, and calculated results are not so plentiful that satisfactory interpolation procedures can be devised. Performing the calculations, however, is a tedious, time-consuming task unless an electronic computer is available, and, in practice, time and manpower are not always available for this purpose. A quick, simple, consistent method was needed for reducing the uncer- tainty in estimated oil recovery from solution gas-drive reservoirs when only minimum information about the reservoir system is available. PROCEDURE Method of Calculation The usual requisite assumptions were made so that the material balance equation could be used to calculate data for the charts. The following assumptions were made: (1) the reservoir is homogeneous and isotropic; (2) oil recovery is due entirely to solution gas drive and neither a gas cap nor a water drive nor gravity drainage is present; (3) the initial reservoir pressure is the bubble-point pressure of the reservoir fluid; (4) initial total liquid saturation is 100 per cent of pore space; (5) interstitial water saturation remains at the initial value as the reservoir pressure declines from the bubble-point pressure to atmospheric pressure; (6) equilibrium gas saturation is 5 per cent of pore space; and (7) oil and gas saturations are uniformly distributed throughout the reservoir at all times. There are no saturation gradients due to a wellbore, nor is the geometry of the reservoir system considered. The material balance equation was written in the form of a differential equation' which was integrated to determine the change in oil saturation for an assigned pressure drop. Formal integration was not possible, so recourse was made to the Runge-Kutta method' of numerical integration. All computations were performed on IBM equipment. Numerical integration yielded the change in oil saturation within the reservoir as the pressure. declined from the bubble-point pressure to atmospheric pressure. The initial oil saturation minus the change in oil saturation yielded the oil saturation at atmospheric pressure. The oil originally in place was obtained by dividing the initial oil saturation by the initial formation volume factor (differential liberation) while the oil in place at atmospheric pressure was obtained by dividing the final oil saturation by the formation volume factor at atmospheric pressure. U1timate oil recovery, expressed as a percentage of the initial oil in place, was obtained by dividing the difference between the oil initially in place and the oil in place at atmospheric pressure by the oil initially in place and multiplying by 100. PVT Data Charts were based upon 135 solutions to the material balance equation. PVT properties of the reservoir fluids were variables in this equation and had to be known as functions of pressure. The required PVT data might have been obtained from either actual reservoir fluid systems or correlated data. However, correlated PVT data were developed and employed in the calculations for the following reasons: (1) it is doubtful that 135 sets of PVT data could have been obtained for the values of variables investigated in this study, and (2) results of recovery calculations from randomly obtained PVT data could not be correlated as well as rssults from selected PVT data. The PVT data used to develop the

Organization Place _ Date 1919 American Iron and Steel Institute New York, N. Y. May National Fire Protection Association Ottawa Can. May 6-8 American Zinc Institute :.. St. Louis, Mo. May 12 American Association of Engineers Chicago, Ill. May 13-14 Natural Gas Association in America Cleveland, 0. May 20-23 American Institute of Electrical Engineers.... Lake Placid, N. Y. June 24-27 American Society for Testing Materials Atlantic City, N. J. June 24-27 American Institute of Min. and Met. Engineers Chicago, Ill. - Sept. 22-27 American Steel Treaters' Society, First Annual Convention Chicago, Ill. Sept. 22-27 National Safety Council Cleveland, U. Sept. 29-Oct. 2 American Foundrymen's Association Philadelphia, Pa. Sept. 29-Oct. 4 Institute of Metals Division, A. I. M. E Philadelphia, Pa. Sept. 29-Oct. 4 American Ry. Bridge and Building Association Cleveland, 0. Oct. 21-23 Geological Society of America Boston, Mass. Dec. 29-31

Jan 5, 1919

By Donald B. Evans, Robert D. Pehlke

The solubility of nilrogen in liquid binary alloys of iron with Litanium. zivconium, columbium, vanndiurn, and tantalum was measured for alloy composiLions up to the solalbility limils of lhe alloy nitrides. All five alloying agents were found to decrease markedly the activity coefficient of nitrogen in liquid ivon. The metal/nitvogen mole ralios in the alloy nitrides formed were generally .found to be slighlly greater than 1.0, but in no case greater than 1.5. From the experimental data, the standard free energies of fortmation of titanium and zir-conium nitrides have been calculated for the Lemperaluve range 1550° to 1750 C. The solublily Products for columbium, tantalum, and vanadium nitrides are also reported. A number of research investigations have examined the effect of refractory metals on the solubility of nitrogen in liquid iron. Although data on zirconium are not available, investigators are in agreement that titanium, vanadium, columbium, and tantalum markedly increase the solubility of nitrogen in liquid iron. This fact alone makes desirable the acquisition of thermodynamic data for these elements in liquid iron. Since refractory metals are known to be stable nitride formers, they have been suggested as steel denitrifying agents, and some of their nitrides have recently been considered as containment materials for liquid iron and iron alloys. Most available thermodynamic data for these metals relate to their dilute concentrations, but effective thermodynamic treatment of these applications requires data at concentrations near the solubility limit of the alloy nitride. Although some work has been done at relatively high alloy concentrations in liquid iron (particularly for vanadium 2,3 and titanium 2,4), the results have been somewhat contradictory. Disagreement may be partly attributed to the fact that the compositions of most refractory metal nitrides have been shown to be nonstoichiometric, and to vary 2,5-8 depending on the temperature and nitrogen gas pressure with which the solid nitride phase is in equilibrium. One purpose of this study consequently has been to determine the compositions of the refractory metal nitrides precipitated from a liquid iron solution. EXPERIMENTAL PROCEDURE Rao and Parlee2 and Evans and Pehlke 9 have discussed the technique for measuring the solubility product of an alloy nitride phase in liquid iron by finding the point of departure of the nitrogen solubility from Sieverts' law. The method consists of measuring the solubility of nitrogen in a melt of iron containing a known concentration of a second metal as a function of the nitrogen gas pressure over the melt. In this study the second metal was one of the refractory metals titanium, zirconium, columbium, vanadium, or tantalum. When the nitrogen pressure at which the refractory nitride forms is reached, a deviation of the measured solubility of nitrogen in the melt from Sieverts' law is observed in the form of a "pressure halt." The concentration of nitrogen in the melt associated with this breakpoint in the nitrogen-absorption curve is then used to calculate the nitride solubility. The Sieverts method was used to measure nitrogen solubility as a function of nitrogen pressure and temperature. The experimental equipment for this technique has been previously described in detail. 1,9 Charge materials used were vacuum-melted high-purity iron (Ferrovac-E) and the best commercial grades of the refractory metals obtainable (in all cases at least 99.8+ pct pure). Recrystallized alumina crucibles were used to hold all melts except those containing zirconium, for which zirconia crucibles were necessary. Temperatures were measured by a disappearing-filament type optical pyrometer sighted vertically downward on the melt surface through a 1/4-in.-diameter sight hole in the crucible lid. By means of a technique previously described, 9 in which the refractory-metal nitride was precipitated at one temperature then redis-solved by raising the temperature 50°C and precipitated again at a higher temperature, it was possible to obtain data over a temperature range of up to 200°C on a single melt. It was found that this technique could not be used with melts containing zir-

Jan 1, 1965

By H. E. Kramm

During the summer of 1910, I had the opportunity to study in detail the geological conditions of what is known in northern California as " Harrison gulch," in Shasta county. Though the district, as a whole, that is, the western part of Shasta and the eastern part of Trinity county, has contributed during the last 15 years a considerable share of the gold-production credited to Shasta county, very little is known of its geology, perhaps because the country is covered with a dense growth of brush which makes exploration and prospecting extremely difficult. Topographically the district presents a succession of ridges trending approximately N-S., and alternating with deep, narrow canyons. The drainage is partly into the Sacramento, partly into the Trinity river. Climatic conditions in summer time are almost ideal. It is true, the thermometer may climb to 115°, but the air is dry

Jan 1, 1913

By Raynor Linzey, Karl M. Busen

The formation of thin films of silicon oxide by anodic oxidation of silicon and the subsequent removal of these films by an etch is a process often used for the evaluation of concentration distributions Profiles) in silicon layers by the differential sheet conductance method. The accuracy of the resulting profile is very strongly influenced by the uniformity of the thickness of the reacted silicon. Normally, it would be expected that for a constant number of coulombs passed the thickness would be the same from oxidation to oxidation. Investigations show that in certain electrolytes, for a given number of coulombs passed through an n-type silicon sample, the thickness of the reacted silicon increased with increasing resistivity. Even for the same resistivity the thickness varied sometimes by a factor of 1.5. When an electrolyte was used which consisted of 10 pct water by volume in ethylene glycol with 4.0 g KNO per 1000 ml of solution, anodiza-tion at 5 ma per sq cm led to satisfying results. Short-time anodizations gave oxide layers of a higher apparent density than those experienced from thermally gown silicon oxides. THE functioning and the electrical characteristics of semiconductor devices are based upon the incorporation of "impurities" into a single-crystalline body of suitable material and on the concentration distribution (profile) of this impurity. The incorporation can be achieved by well-known processes as, for example, by diffusion, epitaxial growth, alloying, or ion implantation. Often the profile resulting from these processes is not known. A powerful tool to learn about a concentration distribution is given by the method of differential sheet conductance which employs successive four-probe measurements on a layer subjected to stepwise removal of thin sublayers. Differential sheet conductance vs position (or penetration depth) of a sublayer is plotted and a smooth curve is drawn through the data. From this curve the profile is then calculated. When the semiconductor material is silicon, the sublayers are removed suitably by anodic oxidation of the silicon and subsequent dissolving of the formed silicon oxide by an etch. The accuracy of the resulting profile is very strongly influenced by the uniformity of the sublayer thickness. Normally, it would be expected that, for a constant number of coulombs passed, the thickness would be constant from oxidation to oxidation. Investigations showed that for sublayers several hundred angstroms thick the reproducibility can be rather poor. Therefore, efforts were made to obtain a reliable technique for uniform removal. The present paper describes such a technique and certain phenomena which were encountered during the investigations. APPARATUS AND TECHNIQUE The first report on the investigation of concentration distributions, where for differential sheet conductance measurements thin silicon sublayers were removed from a diffused layer by anodic oxidation, was given by Tannenbaum. The author reports the removal of sublayers which for the most part were 400 thick. More advanced device designs now require much narrower layers. When it was tried in these laboratories to determine profiles within such layers, difficulties were encountered with respect to sublayers which by necessity had to be thinner than the ones reported by Tannenbaum. The apparatus used for the investigations is sketched in Fig. 1. Two cylindrical containers connected by a wide tube are filled with an electrolyte. The left container receives the cathode whereas the right container is closed at the bottom end by a sample support consisting of a Teflon base and a copper pedestal. The silicon sample (1 by 1 cm) is mounted to the pedestal embedded flush in the Teflon base using silver paint (Degussa) for electrical contact. Pyseal is applied to the edges of the sample to protect the copper pedestal from the electrolyte. The base is mounted to the container using a water-tight silicon rubber gasket. Fig. 2 gives a view of the sample support. The copper pedestal is connected to the positive side of a power supply operating at a constant current output (Kepco Model ABC 425M). The electrolyte which has been reported by Duffek et al. consisted of either 2 or 10 pct water by volume in ethylene glycol and 4.0 g KNO3 in 1000-ml solution. The electrolyte is best prepared

Jan 1, 1967

The Institute offers two distinct relationships to. students: one is an individual relationship as a Student Associate; and the other is a relationship with local organizations of students, known as Student Chapters of the AIME This individual relationship is set forth in Section 8 of Article I of the AIME Bylaws, as follows "A student in good standing in an approved school, who has been nominated by at least three instructors of the nominee (one of whom must be an Institute member), may affiliate with the Institute as a Student Associate by payment of $4.50 annual fee, for which he shall receive one monthly journal and be privileged to attend meetings of the Institute and to use the Engineering Societies Library and the Personnel Service A student may remain such until December 31 of the year in which he ceases to be in university residence as a student "

Jan 1, 1952

By D. H. Yardley

GEOCHEMICAL investigation of trace elements in surface materials was begun near Ely, Minn., in 1953 along the basal contact of Duluth gabbro with Giants Range granite (Fig. 1). This article presents data on the distribution of copper and nickel in till and in stream sediments in the area and proposes an explanation for the types of distribution found. The Duluth gabbro, one of the world's largest basic intrusives, intrudes rocks which range in age from Keewatin to middle Keweenawan. Within the test area the gabbro is in contact with granite except for short sections where it is in contact with remnants of iron formation. Sulfide mineralization occurs within the gabbro, near and parallel to the basal contact for a distance of several miles. Schwartz and Davidson' have described the geologic setting of the mineralization. The sulfides, believed to be syngenetic, include chalcopyrite, cubanite, pentlandite, pyrrhotite, and minor amounts of bornite. They occur disseminated in the silicates and as small interstitial masses. The ratio of copper to nickel is about 3.8:1, based on 66 chemical analyses of rock samples from various outcrops (Ref. 1, p. 702, and Ref. 2). Test Procedures: With specified exceptions, all nickel and copper tests were made by the chromo-graph method,:' which measures the intensity of a colored spot formed by a reaction between the metal being determined and special reagent paper. The intensity is then compared to the intensity of spots prepared from samples of known metal content. Details of the test procedure are outlined in another article (Ref. 4, pp. 77,78). All soil samples tested in this investigation to date have been weighed on an analytical balance. However, a volumetric scoop designed to provide about 0.1 g of soil adds to the speed and ease of testing and has been found to give satisfactory results (Ref. 5, p. 531, and Ref. 19). The size of the samples used for the tests was 0.1 g. Whenever such small samples are used there is some question as to whether they are representative of the several grams in the field sample. Many repeat tests of the samples used in this investigation demonstrated that results can be reproduced within the limits of accuracy of the method without formal mixing beyond that inherent in screening the soil fractions. Furthermore, the 0.1 g is probably as representative of the field sample as the field sample is of its area of influence. Hawkes and Lakin (Ref. 6, p. 291), who considered the general problem, compared ground and quartered bulk samples of 500 g with 5-g grab samples. They concluded that "there is no significant loss in accuracy of data by substituting grab samples for bulk samples." The term soil implies somewhat different things to the geologist, engineer, and soil scientist.' For convenience the term as used in this article refers to unconsolidated material (the mantle) overlying bed rock. Sampling Procedure: Samples were taken at 100-ft intervals along north-south traverse lines across the gabbro-granite contact. The soil (till) samples were taken at an average depth of 1 ft, which was below the high-humus surface layer and into clean till. Samples taken at 1-ft intervals down to ledge showed as high a metal content at 1 ft below the air-surface as at greater depths and in two instances were slightly higher. The till at 1-ft depth did not appear to differ from material at greater depths. Total depth to bedrock has been tested at only a few points and where measured varied from 1 to 10 ft. Aerial Distribution Contours and Profiles: Plotting of copper, nickel, and cobalt content in contour form (Fig. 2) shows that anomalous amounts of these metal ions occur in till over and closely adjacent to mineralized areas of the gabbro. Contouring nickel content alone, or the copper content, outlines the same target area. Contours of the copper content provide a more distinct anomaly than nickel because of the higher copper concentration. The traverses are rather widely spread for interpolation; however, drilling has confirmed the target area essentially as shown.

Jan 1, 1959

By G. H. Anderson

H. R. HANLEY*—I have been asked to discuss briefly the development of rotating cathodes for the electrolytic deposition of cadmium. The earliest recorded use of rotating cathodes was by Hoepfner at Frufurt, Germany about sixty years ago. He elec-trolized zinc chloride solution using diaphragms to separate electrodes. In the early experimental work of the Bully Hill Copper Mining and Smelting Co., Shasta County, Calif., rotating aluminum cathodes 4 ft in diam were used in the electrolysis of an acid zinc sulphate solution. Finished cathodes weighing up to 400 lb were produced. Because of mechanical difficulties, this type of cathode was abandoned for zinc, but was later used for cadmium because of the relative smoothness of deposit in comparison with stationary plates with comparable current densities. Cadmium sponge which forms on the cathode at moderate current densities (without special treatment) is entirely eliminated by a slow rotation. The rate of rotation of the cathode has an effect on the mechanical nature of the deposit. A high rate of rotation concentrates the adhering electrolyte on the shaft; a moderate rate appears to concentrate on the cathode a short distance out from the shaft tending to corrode the deposit in the form of a ring. At a very slow rotation (2 to 3 rpm) the adhering electrolyte gravitates nearly vertically, thus avoiding the cutting ring referred to above. The true explanation for the smoother deposits obtained on rotating cathodes may not be given definitely as the numerous factors involved are not thoroughly understood. Smooth deposits are obtained when the orderly growth of the metal crystals in the cathode lattice are disorganized. Thus the crystals form and grow for a very short interval when they are arrested and a new crystal forms. The continued growth of the original crystals provides large crystals and a rough deposit. Also if the acidity of the electrolyte is low, hydrogen gas bubbles adhere to the deposit. As the cathode is rotated the gas surface is brought into the atmosphere where they burst; thus the deposit is made on a surface relatively gas-free. An aluminum hub distance piece was riveted to each aluminum disk 4 ft in diam, slipped on a 4 1/2 in. steel shaft and pressed tight to prevent acid electrolyte seeping through to the shaft. The 9-cathode assembly was supported on insulated bearings. Electrical contact to the shaft was made through what was equivalent to a copper pulley. Sufficiently high conductivity brushes were placed on the face of the pulley to lead the current to the cathode bus bar. The assembly was driven by a link belt contacting a sprocket insulated from the shaft. The lead anodes were semicircular and supported on porcelain insulators placed on the bottom of the cell. Two anodes were provided for each cathode to permit an 8-in. space between them without increasing the ohmic resistance. This ample spacing permitted easy stripping of deposit with the assembly in place. Cathode cadmium was melted under 650 W cylinder oil. After casting, the primary slabs were remelted under molten caustic soda and cast into pencils 1 1/32 in. in diam. Rotating cathodes for deposition of cadmium are used at Risdon, Tasmania, and at Magdeburg, Germany. W. G. WOOLF*—This paper is very-interesting to me because in our work at the Electrolytic Zinc Plant of the Sullivan Mining Co. we had an exactly similar problem—that is, a method of producing cadmium from our purification residue, the recovery of the contained copper as a copper precipitate which could be sent to a copper smelter and the production of merchantable cadmium. It is interesting to me, not knowing of the work of the Risdon people, how closely we approximate them in their main metallurgy, diverging at several interesting steps which I would like to discuss for just a moment. For example, at Risdon they oxidize their purification residue. In our practice we take the current residue as it is produced in the purification department of the zinc plant and process it in the cadmium plant. The only oxidation that it obtains is the oxidation in the presses, the dumping of the presses and the collection and transportation of the residue to the cadmium plant. We find that the leaching of that residue does not necessarily require the oxidation step that the Risdon people evidently find necessary. The discussion of oxidation comes in again in the matter of the treatment of the precipitated cadmium sponge with zinc dust which again at Risdon is oxidized but which we do not attempt to oxidize except as it oxidizes itself in the storage. There is a partial oxidation which cannot be avoided, as Mr. David-sou pointed out, but we make no attempt to attain a complete oxidation and we dissolve the cadmium sponge in the sul-

Jan 1, 1950

By Peter J. Lean

The introduction oE computer control in the grinding circuit of the New Broken Hill Consolidated Limited concentrator in the early 1970's gave smoother operation at optimum performance. The ore feedrate and water additions to the grinding circuit were controlled to operate each of the ball mill/ rake classifier grinding units at the upper limit of the circulating load while classifier overflow density was maintained to give a product size and pulp density suitable for flotation. An incremental expansion of the concentrator in 1981-82 included the installation of hydrocyclones in closed circuit with three of the four ball mills. Without the rake classifiers in circuit the previous control strategy could not be used and the complex interaction of hydrocyclone performance characteristics when classifying coarse grained sulphide ore resulted in the over-grinding of the lead mineral galena. Testwork aimed at optimising grinding circuit performance recognised the enhanced tendency of higher specific gravity minerals to report to the cyclone underflow. The data has been evaluated on an individual mineral basis and then used to develop a model For grinding circuit control. The development of the model which uses inputs of ore feedrate, metal content of the Feed and slurry density of the cyclone overflow to predict the size of the minerals in the grinding circuit product is described and model predictions are compared with plant performance.

Jan 1, 1984

By D. D. Pollock, G. P. Conard II

Equations of the form of the Mott and Jones equations for the absolute thermoelectric powers of metals are derived primarily from a thermodynamic approach. The behaviors of transition thermoelements in common use are then examined and compared with this simple theory. MOTT and ones' derived a general expression for the absolute thermoelectric behavior of metals and alloys using the approach of the solid state physicist. This expression was then applied to specific cases.1,2 The present work develops equations of the same form principally by a thermodynamic approach. These relationships are then employed to gain some insight to the behavior of the transition thermoelements in common use. I) DERIVATION OF AN EXPRESSION FOR ABSOLUTE THERMOELECTRIC POWER First consider a metallic conductor which is maintained in a temperature gradient with no current flowing. At constant pressure, there will be a gradient of the free energy (F,) given by:

Jan 1, 1963

By B. L. Averbach

Recovery and primary recrystalliza-tion in cold worked metals are usually considered as two competing processes. Some of the effects which usually accompany recovery are: alleviation of stress corrosion tendencies, changes in thermal emf,1 damping capacity,2 electrical resistivity,2 and magnetic properties,3 and only minor changes in hardness or the related strength properties. During primary recrystalliza-tion new unstrained grains are formed at the expense of the strained matrix. These new grains eventually become visible metallographically, and nucle-ation and growth kinetics have been indicated for this process.4,5 Frequent attempts have been made to study the cold-working phenomenon by observations on the line broadening by X ray diffraction patterns. Relatively few measurements of line intensities have been made, although Brind-ley and his collaborators, 6,7,8 by means of film techniques, compared the intensities of cold worked Cu, Ni, and Rh patterns with those from chemically precipitated powders. These precipitated powders were presumed to be strain free, and it was found that the intensities for the cold-worked materials progressively decreased as the Bragg angle increased except for the first line, where there was an increase due to reduction in extinction. This was interpreted as a randomness in atomic position induced by cold work. Such randomness is similar to that caused by thermal agitation and has been described as "frozen heat" displacement of 0.08-0.10 A from the mean atomic position. In a recent study9 on the effect of cold work in metals on their powder pattern intensities, the changes in integrated intensity for heavily cold worked alpha brass were observed as a function of the annealing temperature. These measurements were made with a manually operated Geiger-counter spectrometer using CuKa radiation monochromated with a rock salt crystal. Intensity measurements were made with a scaling meter over small intervals of angle, and the equipment was so arranged that the diffracted and incident beams made equal angles with the specimen. Intensities could be compared directly by simply interchanging specimens, and comparisons from day to day were made with a standard whose line intensities did not change on aging. It was shown that a cold worked alpha brass standard was stable for at least a year. Table 1 indicates the results of the integrated intensity measurements on a 70 Cu-30 Zn brass. In the sample preparation, a brass plate was first cold rolled 50 pct and then filed, screened to —325 mesh, compacted into briquettes at a pressure of 60,000 psi and finally annealed for one hour at various temperatures up to 400°C. The briquetting pressure did not seem to influence the integrated intensities, and most of the cold work was introduced by the filing. Although this method of cold work is not quantitative, it was used to obtain random orientation (and thus uniform diffraction lines) in order to make accurate measurements of integrated intensity. Back reflection patterns were taken in each case to check the uniformity of the lines, and from the observed line broadening it was apparent that this type of plastic deformation was quite severe. Care was taken to traverse the entire background of the pattern and to assign to each peak the total intensity above this background. The bases of the diffraction lines were quite broad and spread out over several degrees, even for the narrow peaks. The theoretical intensities were calculated to include a temperature correction, a dispersion correction, and a Lorenz- polarization factor corrected for the crystal monochromated beam. In Table 1 it was necessary to match the calculated and observed values at only one point, and the rest of the experimental values were converted directly to this arbitrary scale. The integrated intensities in Table 1 are listed in arbitrary units, and the accuracy was sufficient to reproduce any of the measured line intensities to within + 1.5 units. It is evident that the percentage error on the strongest line (111) was quite low. The calculated values and the observed intensities for the cold worked material matched reasonably well. As the annealing temperature was raised, however, the intensity of the strongest reflections, particularly the (lll), decreased measurably. Since the background intensities of all of these patterns were identical, such behavior could be interpreted as a primary

Jan 1, 1950