Search Documents

By P. E. Fitzgerald, Dana G. Hefley

An apparatus has been developed which permits selective acidizing of producing formations and determination of the relative permeability of a formation by fluid injection. This apparatus, known as the "Electric Pilot," is an electrical fluid-interface locator, the electrical circuit of which is completed when the elec-tcodes in the well are in contact with a conductive fluid, but is not completed when immersed in a nonconductive fluid. Results are given for a number of typical acidizing applications in which the interface locator was used to control the acid. Description of the method used in making a permeability survey and the data obtained are also included. Introduction Early in the development of the acidizing industry it was recognized that one of the most important problems to be solved in the chemical treatment of any well was the determination of what part of the exposed section in the well should be treated and the selection of the technique that would insure treatment of the desired section. One of the first techniques adopted for assisting in proper placement of the acid, which is still widely used, is the method of confining the acid to the producing section by means of a column of oil, which is known as the Carr1 method of treatment, named for its inventor. In the Carr method it is not possible to selectively acidize a specific horizon in a multiple pay zone, so many improvements and modifications of the basic Carr technique were devised to accomplish this result. In order to overcome the possibility of the acid entering an undesirable section at the bottom of the well, organic gel plugs2 were introduced into the bottom of the well, which served to halt the entrance of the treating solution into these zones.3 These chemical gels later liquefied because of bacterial action and were removed from the well with the produced fluid. In fields where a gas cap existed, as in the Goldsmith field of Ector County, Texas) it was imperative that a treating technique be evolved that would confine the acid to the oil-producing zone below the gas cap. By so doing the oil-productive capacity of the wells could be improved without greatly increasing the gas production and this would lower the gas-oil ratio of the well. ~h, technique employed4 to achieve this effect utilized two pumps, one for pumping the chemicals down the tubing, the other to simultaneously force oil down the annular space to confine the acid to the oil pay, thus preventing the chemicals from entering the upper gas-bearing zones. Experience has indicated that gas wells and certain types of oil wells respond better to ''stage treating.'' This technique utilizes the introduction of a certain volume of acid and then allows the well to ''clean up99 before introduction of the next and usually successively larger stages. Where such methods are employed steps must be taken to keep a disproportionate share of the acid from entering the most permeable and previously treated Zones. A special tool

Jan 1, 1944

By Paul M. Tyler

MINOR industrial minerals included in this chapter are: the alum minerals, bromine, calcium chloride, epsomite and other natural magnesium salts, iodine, meerschaum, quartz, industrial crystals other than quartz (Iceland spar, tourmaline, fluorite, selenite, mica), and nonfuel gases (air, helium, carbon dioxide). ALUM MINERALS The alums comprise a series of double sulphates (or selenates) isomorphous with potash alum, which, according to a ruling of the Pennsylvania courts, is the only product commercially described simply as "alum." Common alum occurs in nature as kalinite (K2SO4- A12 (SO4) 324H2O). The mineral mendozite (Na2S04) 3.A12 (SO4)3- 24H2O) is soda alum; tschennigite (NH4)2SO4.Al2 (SO4)3.24H2O) is ammonium alum; and there are about a dozen other native alums and related double sulphates. Alunite (alumstone or alum rock) has the formula Al2(SO4) 3.K2S04.4A1 (OH)3 and alunogen, Al2(So4) 3.18H20. Saline residues, found wherever natural water is evaporated, may contain sulphate of alumina, which for most uses is the essential ingredient of alum. Mineral wells and springs that emerge from beds of pyritiferous shale are typically astringent and at times form local deposits of alum, generally as incrustations. Acid waters acting upon aluminous rocks may form sulphates of alumina. The alums of commerce, as well as aluminum sulphate (concentrated alum), are produced principally by treating bauxite with acid, but they have been made also on a substantial scale from clay, cryolite, pyritic slates, schists, lignites, alunite, and leucite. Alum shale-chiefly clay, pyrite, and (usually) carbonaceous matter-was extensively used in England as a source of alum for more than two centuries. In France, pyritic lignites mixed with sand and clay were burned in heaps to red ash, the leach Liquors from which, after treatment with ammonia, yielded alum and copperas. Processes have been developed for making alum or aluminum sulphate from such diverse materials as feldspar, aluminous phosphate minerals, greensand, and mixtures of mica and

Jan 1, 1949

By P. A. Farrar, M. D. Silver, K. L. Komarek

Thermodynamic properties of Hf-0 alloys have been determined from 0 to 25 at. pct 0 between 1000" and 1200°K by equilibrating specimens with alkaline metal oxide-metal vapor combinations. Partial molar-free energies, enthalpies, and entropies of oxygen have been obtained and are conzpared with similar results for the Ti-0 and ZY-0 In continuation of a thermodynamic investigation of the Ti-O and Zr-O systems1 activities of oxygen and lattice parameters of Hf-0 alloys have been deter- system. The positional entropy in all three systems corresponds to an ideal random interstitial solution with one interstitial site per one metal atom. The lattice parameters of hafnium and Hf-O solid solutions have been determined in the range 0 to 20 at. pct O from measurements of Debye powder patterns. mined. All three metals dissolve large quantities of oxygen to form interstitial solid solutions. The phase diagram of the Hf-O system is shown in Fig. 1.' The maximum solubility of oxygen in the cph a phase is considerable (up to 25 at. pct O). The solubility in the high-temperature phase is much smaller. The only stable compound in the solid state is HfO2 which may exist with a certain oxygen deficiency. The low partial pressure of oxygen of Hf-0 alloys required the application of an indirect method. As the most suitable procedure a method, first applied by Kubaschewski to the V-O system,3 was combined with a principle developed by Herasymenko for the

Jan 1, 1963

By Alfred Siegel

Mineral pigments give color, opacity, or body to paint, stucco, plaster, mortar, cement, linoleum, rubber, and similar materials. They must be finely divided, substantially insoluble, and generally inert for such uses. Inorganic pigments may be grouped somewhat arbitrarily as follows: A. Natural mineral pigments dug from the earth. 1. Those consisting mostly of iron oxides, such as hematite and limonite. 2. Those containing large amounts of clay or noncoloring matter, such as ocher, sienna, umber, and colored shales. 3. Those whose color is not due to iron oxide, such as Vandyke brown (including sap brown, an alkali extract of Vandyke brown), graphite, and terre verte. B. Synthetic pigments. 1. Those containing iron oxide as the essential coloring matter, such as "pure" reds, yellows, and blacks, and Venetian reds. 2. Those not containing iron oxide, but rather such compounds as lithopone, zinc white, titanium white, ultramarine, Prussian blue, and the like. Only groups A and B-1 are discussed here. All the pigments in those two categories, except Vandyke brown, sap brown, and some of the carbonaceous slates, contain, as their essential color constituents, one or more compounds of iron; namely, an oxide-limonite (2Fe2O3.H2O to Fe2O3.4H20), hematite (Fe2O3), or magnetite (Fe2O3.FeO). Man's first permanent coloring materials were earth pigments-the ochers, iron oxides, and various iron-stained clays. The caves occupied by prehistoric man and the arts of the ancient Chaldean, Egyptian, and Cretan civilizations bear mute witness to this and also testify to the beauty and permanence of earth colors. As the Roman era developed, earth pigments were pushed from their pre-eminent position by white lead and red lead and in the Middle Ages by zinc oxide. Today, of course, the number of acceptable pigments is very large and on a value basis the group of natural and synthetic earth pigments stands forth with $16,000,000 per year; it is surpassed by titanium, lead and zinc pigments. Of this sum,21 natural pigments supplied 31 pct of the tonnage and 16 pct of the value of the total finished pigment in 1957, the remainder representing the tonnage and value of sales of the synthetic iron oxide colors. The average value of finished natural pigments in 1958 was $80.62 per ton. The average value of manufactured pigments in the same year was $202 per ton. Of the 60,000 tons of manufactured colored pigments sold in 1958, the reds comprised 76 pct of the market and the yellows 20 pct. The reds furnished 68 pct of the value and the yellows 24 pct. Of the finished iron oxide pigments (natural and manufactured) sold in 1958, the reds dominated the market with 66 pct of the quantity and 63 pct of the value; yellows supplied 17 pct of the quantity and 20 pct of the value, and browns furnished 11 pct of the quantity and 10 pct of the value. The average value of the reds was approximately $152, and the average value of the yellows $190 per ton. The highest valued pigment in 1958, with almost 12 pct of the total tonnage and 21 pct of the value of the iron oxide pigment market, was manufactured red from calcined copperas valued at $286 per ton.

Jan 1, 1960

Andy H. Vassiliou – Introduction Ladies and gentlemen,.good evening and welcome to the Paul F. Kerr Memorial Symposium dinner. I believe we are all here to honor the memory of a great teacher and advisor, and a true friend -- Professor Kerr, or Dr. Kerr, or to most of us who were his students, "Pappy" Kerr. Most of us who attended the Paul F. Kerr Memorial Symposium earlier today at the New York Hilton had the opportunity to read, or listen to, or discuss scientific papers presented in honor of Dr. Kerr. In addition, all of the speakers had the opportunity to reminisce about their association with Dr. Kerr, who was credited as having contributed substantially to their graduate education and the development of their careers. Dr. Kerr's two daughters -- Ruth and Nancy -- who attended the Symposium at the Hilton are also here with us tonight. I think we should keep tonight's festivities on an informal basis since we are all old friends or former students of Dr. Kerr. Some of us may want to say a few words about our experiences at the time we were students at Columbia, and hopefully include some anecdotes relating to Professor Kerr. I would like to invite everyone to do so, but first we have arranged for two of us to be the lead speakers, whom I will introduce in a few moments.

Jan 1, 1985

By C. W. Sherman, J. Chipman, H. I. Elvander

J. F. Elliott—This is an excellent piece of work and makes a chemical metallurgist more enthusiastic than ever about what can be done with multicomponent systems, if we have satisfactory data. I have a remark to make on the interpretation of fig. 5. First, I will comment on the problem of activities in solutions. The iron-sulphur system has in its phase diagram an intermediate solid phase FeS. The occurrence of an intermediate phase is normally associated with negative departures from Raoult's law over a portion of the activity curves in the liquid. (Perhaps it would be better to reserve the phrase "departure from ideality" to departures from Raoult's law line rather than to departures from Henry's law line). Fig. 5 indicates that the deviation of the sulphur activity curve from the Henry's law line is negative;

Jan 1, 1951

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION TO OCTOBER, 1904 Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3 24 Lake George, N.Y. Oct. ?78 7 25 Baltimore, Md. Feb. ?79 7 26 Pittsburgh Pa, May ?79 8 28 Montreal, Canada Sept, ?79 8

Jan 1, 1923

By G. Derge, Lo Ching Chang

The chemical and physical propertties of slag systems are of special interest to metallurgists, for nearly all metals are in contact with molten slags during the primary reduction from their ores and then during the subsequent refining and alloying processes that determine their ultimate use. These processes are carried out at high temperatures and involve such complex chemical systems that funda-mental scientific knowledge of the Properties and behavior of these slags is inadequate. Various hypotheses have been Proposed to explain known slag characteristics. The commonest of these regard the molten slag as constituted of compounds that are dissociated in varying degrees into their constituent oxides, as illustrated by Schenckl and the recent Papers of Chipman and co-authors. Another proposal is that these compounds dissociate by com-plete6 or partial ionization, the evidence for which has been reviewed by Martin and Derge.? whatever hypothesis is favored, the exact formulation of these compounds is incomplete. It is based on three principal types of information: 1. Studies of solidified 51% samples by X ray diffraction, petrography, and similar methods that can be used at room temperature. The correlation of this information with the high-temperature properties of the molten slag is uncertain. 2. Studies of slag-metal equilibria, which have the advantage of providing observations on the molten slag at high temperature. However, even these data present problems of interpretation because they require a complete knowledge of the metal phase. 3. Direct measurements of properties of molten slag at the temperature of greatest metallurgical interest. Viscosity, electrical conductivity, specific heats, and similar properties have been measured, but the data of this type are widely scattered and frequently difficult to interpret. Additional direct measurements of properties of molten slag that can be interpreted in terms of chemical behavior are required, and this paper shows that the standard physical-chemical measurement of reversible electrode potentials, which measure the activity of specific constituents, is a fruitful source of such information. The purpose of this investigation, therefore, was to find an electrode combination that would yield reversible electromotive force measurements when dipped into the molten slag to be studied. Slags of the systems cao-sio2 and cao-120,-SiO2 were chosen for study because graphite containers could be used and the data could be correlated with those for viscosity, conductivity, and other proper-

Jan 1, 1948

By G. Derge

The chemical and physical propertties of slag systems are of special interest to metallurgists, for nearly all metals are in contact with molten slags during the primary reduction from their ores and then during the subsequent refining and alloying processes that determine their ultimate use. These processes are carried out at high temperatures and involve such complex chemical systems that funda-mental scientific knowledge of the Properties and behavior of these slags is inadequate. Various hypotheses have been Proposed to explain known slag characteristics. The commonest of these regard the molten slag as constituted of compounds that are dissociated in varying degrees into their constituent oxides, as illustrated by Schenckl and the recent Papers of Chipman and co-authors. Another proposal is that these compounds dissociate by com-plete6 or partial ionization, the evidence for which has been reviewed by Martin and Derge.? whatever hypothesis is favored, the exact formulation of these compounds is incomplete. It is based on three principal types of information: 1. Studies of solidified 51% samples by X ray diffraction, petrography, and similar methods that can be used at room temperature. The correlation of this information with the high-temperature properties of the molten slag is uncertain. 2. Studies of slag-metal equilibria, which have the advantage of providing observations on the molten slag at high temperature. However, even these data present problems of interpretation because they require a complete knowledge of the metal phase. 3. Direct measurements of properties of molten slag at the temperature of greatest metallurgical interest. Viscosity, electrical conductivity, specific heats, and similar properties have been measured, but the data of this type are widely scattered and frequently difficult to interpret. Additional direct measurements of properties of molten slag that can be interpreted in terms of chemical behavior are required, and this paper shows that the standard physical-chemical measurement of reversible electrode potentials, which measure the activity of specific constituents, is a fruitful source of such information. The purpose of this investigation, therefore, was to find an electrode combination that would yield reversible electromotive force measurements when dipped into the molten slag to be studied. Slags of the systems cao-sio2 and cao-120,-SiO2 were chosen for study because graphite containers could be used and the data could be correlated with those for viscosity, conductivity, and other proper-

Jan 1, 1948

By Ronald C. Koo

THE effect of grain size on the mechanical properties of the bcc metals has been a subject of intensive theoretical and experimental study.'-l5 Quantitative relationships have been established experimentally between yield stress and grain size and between the ductile-brittle transition temperature and grain size in a number of metals.6"15 Much significance has therefore been attached theoretically to the grain size dependence. In all these experiments, different grain sizes were always achieved by annealing specimens at various temperatures. The implicit assumption was that any change in the dislocation substructure or in the distribution of impurities which might occur simultaneously with the production of various grain sizes had only a negligible effect on the mechanical properties. The validity of this assumption, however, is questionable. transformation in iron-nickel alloys is actually an extraneous phenomenon due to inadvertent compositional changes in the martensite if the heating rate is not sufficiently rapid. This complication can be avoided by up-quenching for the reversal treatment,5 and then the stabilization does not appear. Clearly, the lattice imperfections and strengthening produced by the reverse transformation are not responsible for the marked stabilization which has been observed by other investigators in these alloys. Data will be presented in this note to show that, at least in recrystallized tungsten of commercial purity, the difference in the ductile-brittle transition temperature of specimens annealed at various temperatures is more a result of a variation in the distribution of impurities rather than of the difference in grain size produced by the anneal. Ductile-brittle transition temperatures in tension were determined on powder-metallurgy tungsten specimens recrystallized at various temperatures. Tensile specimens having a gage length of 1.50 in. and gage diam of 0.18 in. were recrystallized at 1450°, 2000°, 2350°, 2550°, 2750°, or 2800" for 30 min in a vacuum furnace at a pressure of 1 x 10"5 mm of Hg and then tested at a constant extension rate of 8 x 10 per sec in an argon atmosphere from 100" to 800". Typical quantitative analyses of impurities are given in the Table. These results show that, within the precision of the analyses, see Table, annealing did not result in any detectable change in the impurity contents of the specimens, nor was there any detectable difference in purity between specimens having large differences in grain size annealed at the same temperatures . The results of the tensile tests yielded three distinct ductile-brittle transition curves approximately 225' apart. As shown in Fig. 1, data of specimens annealed at 1450°C and those of specimens annealed at 2000°C (O) fell on Curve A. Data of specimens annealed at 2350" and 2550°C fell on Curve B, and those of specimens annealed at 2750" and 2800°C fell on Curve C. The decrease in ductility with increase in annealing temperature became so pronounced that one third of the specimens annealed at 2750" and two thirds of the specimens

Jan 1, 1963

By W. T. Hicks

Visual observation of the oxidation of columbium shows that the protective behavior noted previously in gravimetric work in the early stages of the reaction below 600°C and throughout the reaction at 640°C is associated with an adherent oxide. The fact that the oxide is seen to move outward from the metal at temperatures from 550° to 935°C implies that the reaction takes place at the oxide-metal interface throughout this temperature range. THE work described in this paper further clarifies the complex oxidation kinetics of Cb revealed, for example, by the continuous gravimetric studies of T. L. Kolski.1 Time-lapse motion picture studies reveal details of the reaction not provided by a study of the combustion products. EXPERIMENTAL PROCEDURE Cb specimens were prepared from material with the following typical analysis: 0, 0.03 pct; N, 0.002 pct; C, 0.006 pct; Ta, 0.04 pct; Fe, 0.01 pct; Ni <0.003 pct; and Cr <0.003 pct. Arc-cast ingots were swaged and cold rolled into slabs. These slabs were machined into blocks 7/16 by 7/16 by 7/16 in; 1/16-in. holes were drilled through the large face of the blocks for suspension. The samples were then de-greased and annealed 1 hr at 1200°C in vacuum. The sample was suspended by a platinum and Pt 10 pct Rh thermocouple inside a 1-in. quartz tube in a Kanthal wound furnace (2 in. OD by 4 in. long) equipped with windows 1/2 in. sq. A Cine-Kodak Special II 16 mm motion picture camera was trained on the sample through a Spencer microscope adjusted so that a magnification of X1.5 resulted on the film. Super Anscochrome film was used to record the events in color. Argon was flushed through the furnace while the sample came to temperature. The argon was then replaced by a stream of dry oxygen at 1 atm. Pictures were taken at the rate of eight per second for about 20 sec during the change of atmosphere. Then by use of a Stevens time-lapse device pictures were taken at the rate of four per minute starting within 1 min of the initial oxygen flow. In this manner continuous visual records of the oxidation of pure Cb

Jan 1, 1962

EDMUND NEWTON, Minneapolis, Minn. (communication to the Secretary?).-In discussing the question of the deoxidation of steel and material suitable for performing this function at the end of the heat, it would seem logical also to include the question of prevention of oxidation in the steel or the formation of iron oxide, FeO. I refer to the use of manganese in the basic open-hearth and basic Bessemer processes. The advantages of high manganese in pig iron for these processes have evidently been clearly understood in Germany for a number of years, although little has been written in regard to the exact manner in which the benefits are obtained. In this country, while we make no steel by the basic Bessemer process, our basic open-hearth process is becoming more and more important. Until 10 years ago, in this country, manganese in the pig iron for this process was considered of little value and by many writers it was spoken of as a disadvantage. During the past 10 years, however, in certain parts of the United States, higher contents of manganese in basic pig have been used with considerable success, although there is apparently nothing in our technical literature to show the reasons for this trend. A German book, "The Basic Open-Hearth Steel Process" by Carl Dichmann does, however, offer an explanation. Dichmann says that if the charge for either of the above-mentioned processes contains 3 per cent. of manganese or above, satisfactory steel.

Jan 6, 1917

By B. Post, F. W. Glaser

Three borides of zirconium have been reported: ZrB,l ZrB2,2,3 and ZrB12, 4 The phase relationships, ranges of stability, and some physical properties of these compounds are described. THE zirconium borides differ considerably from one another, particularly with respect to their relative stabilities at high temperatures in the presence of carbon.4,5 ZrB2 is extremelv stable at all temperatures (to the melting point) in contact with carbon. Both ZrB and ZrB12 tend to decompose at elevated temperatures when carbon is present in excess of about 0.5 pct. ZrB forms ZrB2 and ZrC, and ZrB12 decomposes to form ZrB2 and a boron-carbide phase. In the ZrB12 preparation, boron present in excess of that needed to form ZrB2 reacts with carbon, if present, to form carbides, in preference to forming the higher boride. Similar instability of borides, other than diborides of the transition metals of the 4th and 5th groups of the periodic table, has been reported.5,6 special precautions had, therefore, to be taken to minimize carbon contamination in the preparation of ZrB and ZrB12. Reactions below 1400°C were carried out by heating powdered mixtures of zirconium hydride and boron in quartz tubes in a hydrogen atmosphere. For temperatures above 1400°C, reactions were carried out in graphite molds. Carbon contamination from the molds was minimized by employing extremely rapid heating rates to reduce carbon diffusion into the body of the specimen, and by subsequent "shaving" of sample surfaces that had been in contact with the graphite dies. A heating rate of about 2000°C per min was obtained by heating the dies (by direct conduction), using a current of 40,000 amp. Although this type of heating cycle apparently allowed little time for "homogenization," close approximations to equilibrium conditions were usually obtained as a result of the very strongly exothermic reactions between zirconium hydride and boron at elevated temperatures. Reproducibility of results in repeated runs under varying conditions was taken as a reasonable indication that equilibrium conditions had been effectively achieved. Quenching was accomplished by rapidly immersing the entire die, containing the reaction products, in water. Specimens could also be cooled at controlled rates by adjustment of the rate of flow of water through the water-cooled copper electrodes in contact with the graphite dies.

Jan 1, 1954

By A. S. Eve

IN the spring of 1930, the question was raised as to the possibility of estimating the depth to which the pyrrhotite-nickel deposit at the Falconbridge mine extended in the earth. This body is 7500 ft. long, it dips at 80° to the north, and it is fairly straight with slight sinuosities. Dr. F. W. Lee suggested that it might be possible to solve the problem by measuring the vertical magnetic intensity, with a good magnetometer, both near the surface of the earth and also at a level a &apos;few feet higher in the air. The writer regarded this suggestion with some scepticism, but it was decided to put the scheme to a prac¬ tical test. In July, 1930, Dr. Lee, Dr. Keys and I &apos; the writer, with Mr. Joyce and Mr. Belloc as assist¬ ants, made a firm, light wooden platform (Fig. 1) E measuring 4 by 4 ft. on the top, which was 10 ft. above ground. This platform could be moved easily a few yards by four men, and carried across I country in a wagon or by motor truck. Some iron nails were used in its construction, but we were not able to detect their influence on the - Askania magnetometer. Nevertheless, in future work, the use of iron should be completely avoided. Readings were taken along a traverse at right L angles to the orebody, at several stations, both on FIG. 1.-VERTICAL the ground and on the platform. The excess read- ASKANIA MAGNETOM¬ ETER ings, over the dike, as compared with those about 10 ETER ON A FT. HIGH. PLATFORM 800 ft. away, are shown in Table 1. The largest reading, 6.8, is open to suspicion and should be rejected. The depth of the top of the orebody is known by electrical survey, and by actual drilling, to be about 112 to 123 ft., and the covering is sandy glacial drift. Similar readings were taken over a long straight magnetic diabase dike. These also are shown in Table 1. The magnetic vertical intensity is consistently less at the higher level, which is l0 ft. above the lower level.

Jan 1, 1931

By William E. Ford, Edward Salisbury Dana

The Nitrates being largely soluble in water play but an unimportant r81e i~ Mineralogy. SODA NITER. Rhombohedral. Axis c = 0.8276; rr" 1071 A 7101 = 73&apos; 30&apos;. Homeo- morphous with calcite. Usually massive form, as an incrustation or in beds. Cleavage: r (1011) perfect. Fracture conchoidal, seldom observable. Rather sectile. H. = 1.5-2. G. = 2&apos;262.29. Luster vitreous. Color white; also reddish brown, gray and lemon-yellow. Transparent. Taste cooling. Optically -. w = 1&apos;5874, e = 1&apos;3361. Camp. - Sodium nitrate, NaN03 = Nitrogen pentoxide 63&apos;5, soda 36&apos;5 = 100.

Jan 1, 1922

By J. C. Humbert, J. F. Elliott

The solubility of nitrogen in liquid pure Fe, Cr, and Ni, in liquid Fe-Ni, Fe-Cr, and Ni-Cr alloys and Fe-Cr-Ni alloys, has been measured by the Sieverts&apos; type apparatus between 1500° and 1800°C. Tabulations and graphs of the solubility data and activity coefficients are shown. Heats of solution are reported. Interaction coefficients of the several elements in Fe. Cr, and Ni ave also reported. THE solubility of a gas in a liquid metal is usually measured by either the quenching technique or the so-called Sieverts&apos; method. In the quenching method, 1-3 the melt is equilibrated at the desired temperature and pressure with the gas phase having a known fugacity of the gas being studied. The melt is sampled and the sample is quenched and analyzed chemically for its gas content. In Sieverts&apos; method the melt is contained in a closed chamber. The apparent volume of this chamber, i.e. the "hot volume," is usually determined by introducing a known quantity of an inert gas having very closely the same physical characteristics as does the experimental gas. Alternatively, the experimental gas is used with an inert specimen having the same general physical characteristics as does the experimental melt. Subsequently, the experimental melt is equilibrated with the experimental gas by introducing a known quantity of the gas into the calibrated chamber. The solubility of the gas is obtained from P-V-T relationships. The quenching method suffers from&apos; the limitation that some gas may be gained (as in the case of Cr-Fe alloys) or lost (as in the case of Fe-Ni alloys) during solidification and cooling of the sample. With Sieverts&apos; method sampling and analysis are unnecessary. However, errors can result from the difficulty of determining accurately the "hot volume,"

Jan 1, 1961

THE first session, on alloys, took place on Feb. 20, Mr. Hibbard presiding in Mr. Campbell&apos;s absence. The session covered papers on manganese, chrom-ium, and silicon-iron systems. The paper by Mr. Wohr-man was presented by title. This paper showed that manganese produced many of the effects generally at-tributed to carbon and indicated that our ideas on manganese-bearing carbon steels will have to be modi-fied. Mr. Krivobok discussed this paper at length, the gist of the discussion being that Mr. Wohrman had not taken sufficient precautions in carrying out some of his work, particularly as to the effect of silicon content. Mr. O&apos;Neill&apos;s paper was also submitted by title and no discussion was presented. Mr. Kinzel showed an accu-rate determination of .the carbon-free chromium-iron loop obtained by means of a specially constructed tele-scopic dilatometer. The loop ends at 12.2 per cent chromium and the A-3 line at 900° is unaffected by chromium content. The A-4 line runs from 1400° to 900° at 12.2 per cent chromium as an oblique hyperbola. Mr. Armstrong noted that the brittleness in high chromium alloys is often attributed to the gamma trans-formation and, according to Mr. Kinzel&apos;s diagram, this was impossible, as the alloys contain a great deal more than 12 per cent chromium. Mr. Kinzel pointed out that the presence of carbon in the commercial alloys caused the elongation of the loop and made possible local austenite transformation. Mr. Styri discussed the relations of the coefficients of expansion as shown in Mr. Kinzel&apos;s diagram. Mr. Corson presented the iron-silicon diagram as he has worked it out, showing a pre-viously unknown intermetallic compound, Fe3Si, to-gether with characteristic martensitic microstructure varying with the heat treatment. This compound formation is the real cause of brittleness in certain re-gions of the iron silicon system. Dr. Hoyt believed some of the evidence presented by Mr. Corson to be in contradiction to the phase rule. Mr. Corson, however, explained that true equilibrium does not exist under the conditions at hand so that the diagram was accurate in spite of the discrepancies. The meetings of the subcommittee on the physical chemistry of steel making were interspersed through-out the day. Mr. Feild presided and a program of future activities was outlined. This includes plans for a symposium at the next annual meeting and methods for interesting physical chemists, particularly those in the universities, in the steel man&apos;s problems. This committee has been newly formed and bids fair to be especially active. The Iron and Steel Committee met at lunch at the Engineers&apos; Club at noon, with Dr. Mathews presiding. After disposing of the food the report of the Nominat-ing Committee was called for, and the following were elected as officers for 1928: R. H. Sweetser, chairman; F. C. Langenberg and W. J. Priestley, vice-chairmen; and T. T. Read, secretary. The report of the commit-tee appointed at the last meeting to consider publica-tion and general policy for the committee was then called for and freely discussed, after which it was unanimously voted to instruct the new chairman to se-cure from the Board of Directors the necessary author-ization for the Committee to recognize as a Division. This action was reported to the Board at its meeting the following night and the authority granted.

Jan 3, 1928

G. M. TAYLOR,* Colorado Springs, Colo.-The ore treated at the United Eastern is primarily a gold one and is cyanided-the counter-current decantation method being employed. One of our employees visited this plant a few months ago and, on his return, reported that the moisture in the tailing was carrying 20 c. per ton, which would appear to be somewhat high. As this type of plant has been advocated by one of the recognized cyaniding engineering firms in the country, and a number of these plants are in successful operation, it does not seem to me that the dissolved loss could be so high, and I would like to know if any one can give any definite information on this point? J. V. N. DORR, New York, N. Y.-I am very glad that Mr. Taylor has raised this question. When I first read Mr. North&apos;s paper and saw his statement, that they had an actual dissolved loss of 21.5 c. per ton, I was very much puzzled at this high loss which appeared avoidable by another decantation or the addition of a rotary filter. Reading it again, however, I noted that the actual dissolved loss of 21.5 c. given was evi-dently obtained by multiplying the assay of solution discharged from Z. thickener by the tonnage. On the basis of 283 tons milled per clay, this means $56.54 going to the clam. He states, however, that he returns from. the dam into the system, 70 tons daily assaying 40 c. per ton or $28 per day, so it would seem reasonable, unless I have overlooked something to regard the actual dissolved loss as $56.54 less $28 or $28.54, equaling 10.8 c. per ton. Even this loss, however, is much higher than good practice elsewhere, and can be accounted for largely by the tonnage being handled, which I believe is 30 per cent. above the capacity planned.

Jan 12, 1919

By Don B. Shupe, John K. Berry

The handling and disposal of mine water is a much larger problem than is apparent at first glance. Many more tons of water are removed from underground coal mines in the United States each year than tons of coal. In the old anthracite region of Pennsylvania the average was around 32.7 t (36 st) of water for each ton of coal produced, while bituminous mines average about 4.5 or 5.4 t (5 or 6 st). Water encountered in the mines may come from several different sources. In mines with light cover and without a firm solid roof, rain may seep directly into the workings. This is also true of deeper mines where pillar falls have broken the roof to the surface. The top under creek beds is generally faulty and broken and water comes through the roof at this point. Deeper mines are frequently overlain by water-bearing strata and pillar breaks and faulty top can admit water, while places running to the dip often accumulate water which comes up through the bottom. In all cases, except where passing under a year-round stream, the amount of water made is usually pretty closely connected with the weather-more water during the rainy season, less in the dry, although the deeper a nine is, the longer it is before changes in rainfall are felt. Another source of water, not connected with seasonal changes, is old water, accumulated over a period of time in abandoned workings of the mine, or from flooded adjacent mines. Here the water filters through the coal, the parting, or comes up through cracks in the bottom. Similarly, core holes, drilled to prospect the property, can be a source of unexpected water and modern safety requirements for dust-allaying water at the working faces can turn a pleasant working area into a soggy mess over the weekend if the system is not properly maintained and operated. Why water must be disposed of is obvious. If allowed to accumulate, sooner or later the mine will fill up, or at least it will become "roofed" in low places, blocking ventilation and traffic. It must be controlled long before it reaches this stage. Water standing in the working faces is

Jan 1, 1981

By E. W. Lithgow, E. G. Williams, R. R. Holbrook, B. R. Wilson

The mineralogy and geochemistry of Pennsylvanian shales and underclays were studied to determine their suitability for lightweight aggregate and refractory ladle brick. Eighty percent of the variation in bloating of shales and clays was explained by the variation of Si02, A1203, and fluxes (Fe203, MgO, CaO, Na20, and K20); 60% by variation in quartz, kaolinite, illite, and chlorite. The best bloating was exhibited by marine shales, whereas freshwater shales and underclays experienced little or no expansion. Regional paleogeographic maps o f Pottsville and Allegheny shales permit bloating to be geographically predicted. It was found that clays meeting the specifications for refractory ladle bricks were obtained from underclays having over 34.5% mica, over 40% kaolinite and less than 15% quartz. Underclays of this composition are confined to the lower Allegheney outcropping along the near-margins of the coal basin. The best clay is that underlying the Lower Kittanning coal. Porosity of the first fired brick was found to be inversely correlated with reheat expansion.

Jan 1, 1975