Search Documents

George A. Packard, Boston, Mass. (communication to the Secretary†):—The very interesting results obtained by Prof. Hofman and his assistants came to my attention when I had temporarily assumed charge of the metallurgical department of the Missouri School of Mines, and had found it, pending the completion of a new building, lacking a furnace in which to roast ore preparatory to the customary lead blast-furnace run. An attempt at lime-roasting had been already determined upon, but the use of a charge which would make a slag of definite composition was a new idea. The results following were obtained by Messrs. Aubrey Fellows, J. C. Long, E. R. Wash, and Dr. T. C. Tseung, under my supervision. It is regretted that the data are not more complete; but the work was done simply incidentally to securing the desired ore for the blast-

Jan 1, 1908

By R. P. Carreker

GERMANIUM is a member of that group of ele-nents—carbon, silicon, germanium, and tin-— that are currently of particular interest because of their interesting electrical properties. Near room temperature these materials of diamond cubic crystal structure are characteristically brittle. However, there have been several recent reports that germanium is not brittle at elevated temperatures These observations may be summarized as follows: 1—Germanium single crystals were observed to creep in bending under a maximum fiber stress of 6 kg per mm&apos; (8500 psi) at 500°C and above.&apos; The creep curves were sigmoidal, with an induction period that decreased with increasing temperature. 2—Germanium crystal bars have been bent 90" about radii ten times the bar thickness at 550°C.&apos; 3—-Audible clicks were heard when l/4 in. thick crystals were bent drastically at 450" to 500°C. No microstructural evidence of mechanical twinning was observed 4—Slip lines have been observed in tensile specimens deformed at 600°C, and are coincident with (111) planes, the close-packed planes of the diamond cubic structure.] The slip direction has not been established. 5—A germanium crystal has been compressed approximately 20 pct along a <110> axis at 700°C." The results reported subsequently were obtained in exploratory experiments intended to indicate some aspects of the behavior of germanium single crystals when tested in simple tension. Specimen Preparation A single crystal bar of n-type germanium was used. It was of purity corresponding to a resistance range of 2 to 20 ohm-cm. Tensile specimens were prepared by cutting small rectangular bars

Jan 1, 1957

Reserves of Lake Superior Manganiferous Iron Ores Appendix-to paper by CARL ZAPFFE, presented at the Cleveland Meeting and issued, as Pamphlet No. 1664-C, with MINING AND METALLURGY, May, 1927. The author has made several test calculations on the basis of manganese units that are and may be involved. These are summarized here, as follows: On the basis of ore produced since 1902, the average annual requirement of manganese units would be 91,000 tons; on the basis of the production of the past 4 or 5 years, the requirement would be 145,000 tons; on the basis of the year 1925 only, the requirement would be 155,000 tons. Applying the percentage of increase for the next 20 years, as determined by the plat shown as Fig. 3, the total requirement for 20 years would be 3,254,000 to 3,572,000 tons, if one used either 145,000 tons or 155,000 tons as a starting point. We have the following interesting facts: (1) The Michigan ores contain only about one-half the manganese that the Cuyuna ore does; (2) the Cuyuna district now produces one-half the ore required; (3) the known tonnage of Cuyuna reserves is greater than the speculative reserve offered for Michigan; (4) at the present rate of production considered by tons, Michigan ores ought to be exhausted in 20 years or less while Cuyuna ores would last up to 44 years. We should now reduce the estimated reserves to a basis of manganese, units. Using the tonnages listed in Combinations 2, 3, 4 and 5, the reserves total 3,118,225 tons, 3,781,995 tons, 5,041,995 tons and 5,560,342 tons, respectively. Therefore, needing at the most 3,572,000 tons, as shown above, either Combination 3, 4 or 5 will not only suffice but will leave an excess-enough for 1 or 2 years for Combination 3, 9 or 10 years for Combination 4, and 12&apos; to 13 years for Combination 5. This means that for Combination 5, without using tonnages obtained from beneficiating or from mixing poor ores, the reserves are ample for about 33 years.

Jan 5, 1927

US 4,185,193-Method of assaying the vicinity of a borehole for uranium ore or thorium ore. A pulsed neutron source IS operated to irradiate the earth formations with fast neutrons. A detector responds to the delayed fission neutrons emitted by the ore as a measure of ore concentration and to the delayed neutrons from oxygen-17 as a measure of the neutron output of the source. The measurement of ore concentration is corrected In accordance with the measured changes in the neutron output of the source. R L. Caldwell, assigned to Mobil Oil Corp. Jan. 22, 1980 4 pp (250-269). Filed: 5-18-78 (906,907).

Jan 1, 1982

By L. O. Howard

R. HATCH, Garfield, Utah.-The object of the meeting, I believe, is to determine the proper chemical composition to insure long wear of a ball in a mill, This might also apply to rods. I feel that there is only one way of determining accurately the wearing qualities of balls in mills, and that is by actually wearing out 400 or 500 tons of different kinds of balls. Two things add to the wearing qualities of a ball: (1) the tenacity, with which the particular particles of iron or steel are cemented together; (2) the individual hardness of each particle. My experience is that a ball that has a Brinell of 550 to 650 will give comparatively long life. There is considerable difference of opinion as to the best steel and iron alloys necessary to produce a satisfactory grinding ball. Some favor chrome, some manganese and some nickel. Personally, I believe cast iron alloyed with chrome makes the best ball for small sizes; for large sizes (3 1/2 in. and up) steel alloyed with manganese is best. L. 0. HOWARD, Pullman, Wash.-How would this method apply to lining? A. KissocK, New York, N. Y.-I do not subscribe to that exactly. As I am connected with the Climax Molybdenum Co. you would hardly expect me to. We have been much interested in trying to work out this grinding-ball problem and have spent a great deal of thought and effort on it. As we are associated with the American Metal Co. and have a number of properties of our own, we are in position to try our ideas on ourselves first. We have tried different compositions, but have not done anything very remarkable with them yet, except that we have been able to say that the combination of chrome and molybdenum has given the best wearing ball. Mr. Hatch feels that iron is the best medium for grinding, but since toughness as well as hardness is a factor in wearability we feel that a well made steel is better for this purpose. Another difficulty with cast, or chilled, iron is lack of uniformity from day to day or from heat to heat and the impossibility of producing balls free from blow or shrinkage holes which materially affect their life. If cast iron is made hard it becomes brittle and lacks stretch or toughness. This prevents its use in the larger sizes, as breakage is a serious handicap to efficiency. We have tried hard and brittle balls and softer but very tough balls and have proved that maximum hardness, with sufficient toughness to prevent breakage, is the most important factor in resistance of a steel to abrasion. It is well known that chromium is one of the best hardening agencies for either iron or steel, and molybdenum is recognized as an element capable of introducing toughness. In other words, the proper combination of chromium and molybdenum permits unusual hardness with still sufficient toughness to stand up under severest impact. It is yet too early to give any actual mill results of this new combination and though we are proving our ideas at our own properties we have to depend on others to help us make the data more general and more worth while and would like to get some tests

Jan 1, 1928

By S. K. Nowak

The lithium solubility limit in solid aluminum was determined by the use of micro-graphic techniques. The solubility limit thus established was shown to be a true equilibrium by checking the reversibility of AlLi phase precipitation and dissolution around the equilibrium temperature. The experimental results fit a straight line by plotting log N(LI) against 1/T. The metallurgical reasons explaining the lack of agreement among previous investigations are discussed. THE solubility limit of lithium in solid aluminum was determined by Shamray and Saldau1 by micrography and by Grube et al.&apos; and also Voss-Kiihler- by measurement of electrical resistivity. Since the addition of lithium induces extremely small changes in the aluminum lattice, X-ray techniques could not be employed for this purpose; in fact, the addition of lithium does not cause an expansion of the lattice as might be expected from a consideration of atomic radii, but causes a small contraction from 4.040 to 4.037A3, 4 when the solvent aluminum is saturated with this element. An analysis of the results from previous investiga-tions&apos;" shows that with improvement of investigation techniques the solubility limit tends toward a lower lithium content. Again, some of the author&apos;s own experimental results on the action of atomic hydrogen on A1-Li alloys seemed to indicate that the solubility of lithium should be much lower, i.e., about 0.3 pet at 300°C: instead of 1.15 pet, the lowest published value.4 For the foregoing reasons it was decided to investigate this problem. The aluminum and the lithium used for this purpose were of the highest purity. The lithium solubility limit was determined by metallographic techniques, in particular by the use of a reagent especially developed for the purpose of revealing the AlLi phase. The solubility limit thus determined was shown to be a true equilibrium by checking the reversibility of AlLi phase dissolution and precipitation around the equilibrium temperature. All of the experimental work was carried out in 1951 at the Centre d&apos;Etudes de Chimie Metallur-gique at Vitry, France, under the direction of Georges Chaudron.

Jan 1, 1957

The Duluth Engineers&apos; Club was formally organized on the evening of Aug. 5, 1918, at a meeting .attended by over l00 members of the several engineering professions. W. G. Swart, a member of our Institute, was elected the first President of the Club. At the organization meeting, an opportunity was given, to Alfred D. Flinn, Secretary of the United Engineering Society, to outline the assistance that is being rendered to the Federal Government in the present contingency by members of the engineering profession. Membership in the Duluth Club is to be open to mining engineers on the iron ranges as well as to the residents of the city of Duluth.

Jan 10, 1918

THE following employment items are made available to AWE a non-profit basis by the Engineering Societies Personnel Service, Inc., operating in cooperation with the Four Founder Societies. Local offices of the Personnel Service are at 8 W. 40th St., New York 18; 100 Farnsworth Ave., Detroit; 57 Post St., San Francisco; 84 E. Randolph St., Chicago 1. Applicants should address. all mail to the proper key numbers in care of the New York Office and include 6c in stamps for forwarding and returning application. The applicant agrees, if placed in a position by means of the Service, to pay the placement fee listed by the Service. AIME members may secure a weekly bulletin of, positions available for $3.50 a quarter, $12 a year. MEN AVAILABLE Executive Engineer, Mining Engineer Graduate, 25 years&apos; management experience from plant operation to vice president in charge of manufacturing for national concern. Management and operational experience in gypsum, asbestos, cement, paper, felt, asphalt products. West Coast or South location preferred. Prefer permanent position but would consider connection on consulting basis. M-663. Geologist and Engineer, E.M. (Geol.), Ph.D., 46, married, excellent health. Nineteen years&apos; broad experience including appraisal, acquisition, large-scale exploration, special problems, planning, organization, and supervision in U.S., Africa, and South America. Sound approach and execution, writes clearly. Currently employed but available short notice. M-660. Mining Plant Designer. Over thirty years&apos; broad mining experience. Graduate mining engineer, registered mechanical engineer, experienced structural engineer. Member AIME, NSPE. Fully experienced all phases design, from initial plant layout to final details. Excellent references. Presently employed but available reasonable notice. M-661-238-Chicago.

Jan 1, 1952

THE CHAIRMAN.-Thank you. Since the papers are rather closely related, I think rather than taking them one at a time we will entertain discussion on any of these problems at this time. W. A. REICH.*-We, of course, quite a while ago got the yellow light that Mr. Cole spoke of, and like everyone else immediately started to study silicon bronzes and brasses. We were interested in the silicon bronzes and brasses because we felt that in order to replace gun metal which makes up a large part of our use we needed something with an elastic limit at least equal to that of gun metal. That means at least 12,000 lb. per sq. in. This study was aimed only at tin conservation. Then we dropped the study of silicon bronzes because high purity copper which is needed in their manufacture became a scarce item. To make a long story short we have recommended to our designing engineers that they use 85-5-5-5 wherever possible because 85-5-5-5 we understand can be made entirely from scrap with little or no tin addition. 85-5-5-5 has a lower elastic limit than 88-8-4, so we felt that we would need another substitute material, a structural alloy with an elastic limit equal to that of 88-8-4, and we immediately turned to the manganese bronze type of alloy. The poor foundry properties of standard manganese bronzes were mentioned by Mr. Thieme and since we feel that high zinc content is largely responsible for this difficulty, our development is directed along the lines of uncovering a material with a lower zinc content and which gains its elastic strength from the addition of other alloying elements, such as, aluminum, manganese and iron. It must be possible to make this alloy entirely from scrap with no additions of scarce high purity material. I would appreciate an expression of opinion on how low we can go in zinc content with this type of alloy without seriously impairing the availability, and how high we can go in aluminum content without making use of aluminum restricted for that use. We assume that the maximum lead content must be placed at 1 ½ per cent to insure good availability and we feel that about I per cent of tin in the alloy would improve salt water corrosion resistance similar to the effect of tin in Admiralty Metal. Has anyone here had experience with the effect of tin and lead on the weldability of such an alloy? C. S. COLE.-What percentage of lead and tin? W. A. REICH.-About 1 per cent of lead and 1 per cent of tin. We are studying the weldability of the alloy but perhaps someone already has the answer. (Pause, no answer) The claim has been made that 1 per cent of lead can be added to certain silicon bronzes without impairing their properties. A silicon bronze with a low zinc content requires high purity copper in its manufacture but if say the 15 per cent zinc, 44 silicon balance copper alloy could be made, with a I per cent lead content, some quantity could be made from scrap. We do not know whether the aforementioned is

Jan 1, 1943

By Tracy C. Jarrett

In making gold alloys possessing certain physical properties, such i~nportant factors as corrosion resistance, color, hardness and melting points must be considered. All of these requirements depend directly upon the composition. It is possible to obtain the same colored gold alloy by using different compositions, but in doing so one may bring in some undesirable property. Other investigations have been carried on in this field by F. E. Carter,&apos; E. M. Wise12 and L. Sterner-Rainer2 To make a complete study of the effect of composition upon these properties, a systematic investigation was carried on involving a range of copper content from 85 to 65 per cent. Elements such as zinc, silver and nickel were used to replace in part the copper content. The gold content in all the alloys remained constant. Only 10-karat gold alloys of those containing 41.6 per cent gold will be considered. All of the alloys were made in an induction furnace. Each alloy was cast in a 3 by 1/4 by 3/4-in. ingot. The method of obtaining the melting points and making color determinations was described in a previots paper.4 The Rockwell B scale with the 1/16-in. ball and 100-kg. weight was used for all hardness determinations. The submersion of test pieces in concentrated nitric acid is one of the standard corrosion tests used in the optical trade. A test piece in the 50 per cent cold-worked condition, % by 2 by 0.045 in., is blanked from a skip using a die, and the weight loss per square inch of surface is taken as a means of comparison. The time for this test is 2 1/2 hr. of actual submersion of the test picce in the acid. This standard test was applied to all of the 10-karat gold alloys discussed in this paper. The tensile tests were made upon strips of the dimensions shown in Fig. 1. The test pieces after blanking were annealed at 1300" F. for 20 min. and cooled in air. Thc "drop of the beam" method was used in determining the yield point, as there was a very marked "drop" when the yield point was reached.

Jan 1, 1940

By Tracy C. Jarrett

In making gold alloys possessing certain physical properties, such i~nportant factors as corrosion resistance, color, hardness and melting points must be considered. All of these requirements depend directly upon the composition. It is possible to obtain the same colored gold alloy by using different compositions, but in doing so one may bring in some undesirable property. Other investigations have been carried on in this field by F. E. Carter,&apos; E. M. Wise12 and L. Sterner-Rainer2 To make a complete study of the effect of composition upon these properties, a systematic investigation was carried on involving a range of copper content from 85 to 65 per cent. Elements such as zinc, silver and nickel were used to replace in part the copper content. The gold content in all the alloys remained constant. Only 10-karat gold alloys of those containing 41.6 per cent gold will be considered. All of the alloys were made in an induction furnace. Each alloy was cast in a 3 by 1/4 by 3/4-in. ingot. The method of obtaining the melting points and making color determinations was described in a previots paper.4 The Rockwell B scale with the 1/16-in. ball and 100-kg. weight was used for all hardness determinations. The submersion of test pieces in concentrated nitric acid is one of the standard corrosion tests used in the optical trade. A test piece in the 50 per cent cold-worked condition, % by 2 by 0.045 in., is blanked from a skip using a die, and the weight loss per square inch of surface is taken as a means of comparison. The time for this test is 2 1/2 hr. of actual submersion of the test picce in the acid. This standard test was applied to all of the 10-karat gold alloys discussed in this paper. The tensile tests were made upon strips of the dimensions shown in Fig. 1. The test pieces after blanking were annealed at 1300" F. for 20 min. and cooled in air. Thc "drop of the beam" method was used in determining the yield point, as there was a very marked "drop" when the yield point was reached.

Jan 1, 1940

By A. E. Lee

THE Blackwell Zinc Co., Inc., a subsidiary of the American Metal Co., Ltd., operates a horizontal retort zinc smelter at Blackwell, Okla. The plant has 14 furnace blocks of 800 retorts each, fired with natural gas on a 48 hr cycle. Over 13,000 tons of zinc-bearing material, chiefly sulphide flotation concentrates, are treated monthly to produce slab zinc and high lead-cadmium fume. In 1942 a program of rebuilding and modernizing the smelter was started. By 1947 furnace smelting capacity had been increased to a point where roasting and sintering facilities were inadequate, and it was necessary to purchase oxidized materials to supplement sinter production. The seven 210 ft Ropp roasters and three 42 in. x 44 ft Dwight-Lloyd machines then in use had been in service at least 20 years and were in need of major rebuilding. Thus it was entirely practical to consider all new equipment and a change of method rather than rebuilding and repairing obsolete units. A study of the problem indicated that roasting as such could be eliminated and roasting and sintering accomplished in one step by a modification of the Robson process,&apos; which had been used since the early 1930&apos;s by the National Smelting Co., Ltd., at their plants at Avonmouth, England, and Swansea Vale, South Wales. Francis P. Sinn, General Manager, Zinc Smelting Operations, The American Metal Co., Ltd., who was familiar with the practice in England, suggested the use of one large machine for the entire operation from concentrate to sinter. One step sintering appeared to best meet Blackwell&apos;s plant requirements and indicated substantial savings in labor, gas, coal, and repair costs. Choice of Machine Size The sinter machine size was set at 12x168 ft for a rated capacity of 540 tons per day. This tonnage, produced on a five day week, would meet the seven day requirements of the 14 furnace blocks. The one large machine was quoted at a lower cost than two or more 6 ft wide machines of similar total capacity. Further, the larger machine could be housed in a smaller structure and only one set of equipment for charge preparation and delivery and for disposal of sinter cake was needed. One machine on a five day week made possible a concentration of the skilled operating personnel and required less men than a plant including two or more machines and related equipment circuits. Fewer units of equipment meant less maintenance, and the two down days weekly allowed ample time to repair and, if necessary, to make up lost production. Experience had indicated better sintering quality and rates with larger masses of material, not only on wider machines, but also in deeper beds. The ratio of windbox perimeter to area for the 12x168 ft machine is 0.179, compared to 0.353 for a 6x102 ft machine and 0.617 for a 42 in. x 44 ft machine. This meant less air leakage with resulting fan power savings and less spoilage of charge along the pallet sides. Performance Initial operation of the new sinter plant was made in November 1951 and regular production attained late in December. The average product sinter output during 1952 and the first half of 1953 has been 18.2 tons per hr. The average for one month has been as high as 22.4 tons per hr. Considerable experimenting with varied operating conditions accounts in part for the below capacity — 24 tons per hr — average output, and work to further improve production rate continues. A typical sinter analyses is 66.0 pct Zn, 0.3 pct Pb, 0.1 pct Cd, 0.3 pct S, 8.0 pct Fe, 2.0 pct SiO,, 0.8 pct CaO, and 0.2 pct MgO. Use of this material has made possible increases in furnace burden and improved furnace operation over the former practice using sinter made from Ropp roasted concentrates. Better lead and cadmium elimination in sintering has permitted the furnace production of slab zinc lower in lead and cadmium. Anticipated economies of operation have largely been gained. The sinter plant is operated by seven men per 8 hr shift — one head operator, three equipment operators and three sweepers — plus one oiler on day shift only. While it has been necessary at times to operate seven days a week to produce the required sinter tonnage, the five day work week usually has been adequate. Consumption of natural gas for sinter bed ignition is 200,000 to 300,000 cu ft per day. Green Ore Sintering Practice The 30 to 31 pct sulphur content of the —200 mesh zinc concentrates is the fuel used to sinter the charge, no coal addition being required. In the feed to the machine, sufficient concentrates are added to crushed return sinter fines containing 0.3 to 0.5 pct sulphur to produce a charge averaging 5.0 to 6.5 pct sulphur. Since the return sinter used in Blackwell&apos;s practice is varied from — 1/2 to — 1/8 in., the actual sintering mixture of fine sinter and concentrates is somewhat higher in sulphur. The coarser sinter particles are too large to resinter and merely aid porosity in the sinter bed. The ratio of concentrates to return sinter in the charge ranges from about 1:4 to 1:5.5. Variations are based on the appearance of pried up bed sections, bed exit gas temperature trends, windbox suctions, and return sinter size. Sufficient sulphur must be used to obtain fritting of the charge into a soft sinter cake and to aid in the elimination of lead and cadmium. Excessive feed sulphur will result in partial slagging of the cake impairing porosity and prolonging sintering time.

Jan 1, 1954

By S. A. Mersol, C. T. Lynch, F. W. Vahldiek

The microhardness of single crystals of tungsten disilicide has been investigated by the Knoop method. The average random room-temperature hardness of the WSi, matrix was 1350 kg per sq mm. Hardness crnisotropy was noted with respect to plane and indenter orientation as determined by single-crq.stal X-rny studies. Annealing at 1600" and 1800°C decreased the average hardness to 1310 and 1230 kg per sq tnm, respectively, and produced a second phase identified by X-ray diffraction and electron-microprobe analysis to be wSio.7. Ball-impact experiwzents produced rosettes at 850°C. Optical and electron microscopy showed evidence of slip and cross slip and twinning produced by microhardness indentations. Prismatic (100), [001] slip was found and cor~elated with hardness data. THE present study was undertaken to investigate the hardness anisotropy of as-grown and annealed single crystals of tungsten disilicide. The existence of the silicide WSiz in the W-Si system has been well-established and its structure thoroughly investigated zachariasen2 found WSi, to have a tetragonal C type of structure, similar to that of MoSi, with lattice parameters a = 3.212A, Kieffer et al. studied the W-Si system and measured the density and microhardness (at a 100-g load) of both polycrystalline WSi, and WSi,.,. The values found were 9.25 g per cu cm and 1090 kg per sq mm for WSi,, and 12.21 per cu cm and 770 kg per sq mm for WSi0.7, respectively. According to Samsonov et a1.5 the microhardness of polycrystalline WSi2 is 1430 kg per sq mm (at a 120-g load). EXPERIMENTAL The WSi, single-crystal boules investigated in this paper were grown by a Verneuil-type process using an electric arc by the Linde Division of the Union Carbide Corp.6 The largest specimens were 8 mm in diameter by 16 mm long. The crystals had an average density of 9.01 g per cu cm with a tungsten • silicon content of 99.9 wt pct. The major impurities were: 87 ppm O, 41 ppm N. 54 pprn C, 500 ppm Zr, 50 ppm Na, and 50 ppm Mn. The crystals were silicon-poor, the average silicon content being 22.20 pct (stoichiometric value is 23.40 pct), and tungsten-rich, the average tungsten content being 77.70 pct (stoichiometric value is 76.60 pct). As-received single crystals were ground and analyzed by powder X-ray diffraction technique using Cu Ka radiation. Laue and layer line rotation patterns were obtained on cleaved sections of WSi, single crystals. Electron-microprobe traverses of representative crystals were done using a Phillips-AMR electron microanalyzer. Carbon replicas were used to prepare electron micrographs. This work was done with a JEM-6A electron microscope. Prior to the metallographic examination, the specimens were mounted in Lucite and then polished for short times on polishing wheels using 9-, 3-, and 1-p diamond-grade pastes. Finally they were fine-polished with Linde A powder for 24 hr on a Syntron vibratory polisher. The samples were etched with 4H 2 O:1HF:2HNO3, which is a medium fast-acting etchant. The combination 1HF:2HNO3:5 lactic acid is also a satisfactory etchant. Annealing runs for selected specimens were made at 1600" and 1800°C for 3 hr at 1.0 to 3.0 x 10-5 mm Hg. A Brew tantalum resistance furnace with WSi2 powder for setters was used. The WSi2 powder was the same as that used for the crystal growth. Temperatures were measured with a calibrated W, W-26 pct Re thermocouple and a microoptical pyrometer. Powder X-ray diffraction, emission spectrographic, and electron-microprobe analyses were done after the annealing runs. For microhardness measurements a Tukon Microhardness Tester Type FB with a Knoop indenter was used. Although measurements were taken at loads ranging from 25 to 1000 g, the 100-g load was chosen as the standard load. All measurements were taken at room temperature. Only indentations of cracking classes 1 and 2 were considered.&apos; DISCUSSION OF RESULTS Powder X-ray diffraction analysis showed the as-received crystals to be single-phase WSi2. Laue and layer line rotation patterns obtained on cleaved sections of WSi2 single crystals proved them to be tetragonal WS 2 2 The results also indicated that the c axis of the crystal was oriented parallel to the boule or growth axis. Electron-microprobe traverses across the matrix of the as-grown crystals showed them to be homogeneous WSi,. Optical and electron microscopy of etched crystals, however, revealed that they contained minute amounts of the "golden" and the "blue" second phases as opposed to the "white" or WSi2 phase. These two second phases were concentrated in inclusion and etch-pit

Jan 1, 1965

By Masayuje Otagawa

The mining methods adopted in Japanese mines are less known to the mining world than those of other countries, owing to the geographical remoteness, but they present many features of interest to mining engineers. The Ashio copper mine is at the town of Ashio, in Tochigiken, about 109 mi. (175 km.) from Tokyo by the Imperial Government railroad. The area of the concession owned by the Furukawa Mining Co. is 5000 acres (5023 ha.). The mine was formerly divided into three, viz. Hon-ean, Kotaki, and Tsudo, which are distant 3 mi. (4.8 km.) from each other as shown in Fig. 1. However, in 1914, when the writer was general manager, the three mining plants were amalgamated into one with the result of simplifying the working projects and increasing the operating efficiency. The mine was visited by the Institute party in November, 1911, when K. Inouye was the general manager. Shortly afterward, the writer was appointed manager, and, in 1915, he was succeeded by Dr. K. Asano. At the end of 1917, K. Kibe became general manager and, after two years, was succeeded by the present manager, I. Sugimoto. For some time Dr. J. Kojima was acting general manager. It is necdless to say that the gentlemen mentioned are all members of the Institute, as is also Baron T. Furukawa, president of the company. Since the discovery of the enormous masses, called "kajika" or "bullhead" deposits, which the writer has described elsewhere,&apos; the mining methods have been varied to meet the different conditions presented by these deposits. The Ashio Ore The country rock of this mine consists of the middle Chichibian slate and quartzite into which has been intruded a post-Tertiary plagio-liparite neck more than 2 mi. in diameter, in the shape of an inverted cone which narrows downward to a relatively small diameter in depth.

Jan 1, 1923

By Masayuje Otagawa

The mining methods adopted in Japanese mines are less known to the mining world than those of other countries, owing to the geographical remoteness, but they present many features of interest to mining engineers. The Ashio copper mine is at the town of Ashio, in Tochigiken, about 109 mi. (175 km.) from Tokyo by the Imperial Government railroad. The area of the concession owned by the Furukawa Mining Co. is 5000 acres (5023 ha.). The mine was formerly divided into three, viz. Hon-ean, Kotaki, and Tsudo, which are distant 3 mi. (4.8 km.) from each other as shown in Fig. 1. However, in 1914, when the writer was general manager, the three mining plants were amalgamated into one with the result of simplifying the working projects and increasing the operating efficiency. The mine was visited by the Institute party in November, 1911, when K. Inouye was the general manager. Shortly afterward, the writer was appointed manager, and, in 1915, he was succeeded by Dr. K. Asano. At the end of 1917, K. Kibe became general manager and, after two years, was succeeded by the present manager, I. Sugimoto. For some time Dr. J. Kojima was acting general manager. It is necdless to say that the gentlemen mentioned are all members of the Institute, as is also Baron T. Furukawa, president of the company. Since the discovery of the enormous masses, called "kajika" or "bullhead" deposits, which the writer has described elsewhere,&apos; the mining methods have been varied to meet the different conditions presented by these deposits. The Ashio Ore The country rock of this mine consists of the middle Chichibian slate and quartzite into which has been intruded a post-Tertiary plagio-liparite neck more than 2 mi. in diameter, in the shape of an inverted cone which narrows downward to a relatively small diameter in depth.

Jan 1, 1923

THE hall of the Western Iron and Nail Associations having kindly been placed at the service of the Institute, the opening session was held at 3 o&apos;clock, Tuesday afternoon, May 13th, with an attendance of about one hundred and twenty-five members. Mr. William Metcalf, of Pittsburgh, read an address of welcome on behalf of the Local Committee of Arrangements, to which President E. B. Coxe responded. The following papers were then read and discussed : Regenerative Stoves; a Sketch of their History and Notes on their Use, by John M. Hartman, of Philadelphia. Some Curious Phenomena Observed on Making a Test of a Piece of Bessemer Steel, by William Kent, of Pittsburgh. On the Use of Determining Slag Densities in Smelting, by Thomas Macfarlane, of Wyandotte, Michigan. After the reading of these papers each member was presented by the Local Committee with a schedule of excursions, a specially prepared map of Pittsburgh and surroundings, and a directory of industrial works, all tastefully bound, and also with a metal badge bearing the seal of the Institute, to be worn on the excursions. The second session was held on Tuesday evening. The following persons, duly proposed for members and associates of the Institute, were, on the recommendation of the Council, unan¬imously elected. (In this list are included those elected at the final session on Friday morning.) George Bartol, - Cleveland, Ohio. Luther S. Bent, - Steelton, Dauphin Co., Pa. Octave Chanute, - New York City. Albert H. Childs, - Allegheny, Pa. Theodore Cooper, - New York City. Andrew Cosgriff, - Brewster, Putnam Co., N. Y. William B. Crocker, - New York City. Henry M. Curry, - Pittsburgh, Pa. Charles Davis, - Allegheny, Pa. Henry F. De Bardeleben, - Birmingham, Ala. Herbert Du Puy, - Pittsburgh, Pa. Charles L. Fitzhugh, - Pittsburgh, Pa. W. S. Franklin, - Ashland, Md. F. G. Fricke, - Pittsburgh, Pa. Paul A. Fusz, - St. Louis, Mo. Ignatius Hahn, . Pittsburgh, Pa. Henry Hargreaves, - South Pittsburgh, Tenn.

Jan 1, 1880

By Charles Will Wright

DESPITE the war, the First Pan American Mining Congress, held in Santiago, Chile, Jan. 15-23, was attended by about 300 persons including the official delegates from sixteen of the American republics. The United States delegation consisted of Elmer Pehrson, of the U. S. Bureau of Mines; D. F. Hewett, of the U. S. Geological Survey; William H. Hobbs, of the Carnegie Foundation; and C. W. Wright, delegate of the Board of Economic Warfare and of the A.I.M.E. Mr. Wright was elected to head the delegation. Among the other members were Edward Steidle, of Pennsylvania State College and also an official A.I.M.E. delegate; John Huttl, of Engineering and Mining Journal; W. 0. Vanderburg, foreign mineral specialist from Lima, Peru; O. B. Hundley, of the American Cyanamid Co.; Horace Graham, of the Anglo-Chilean Nitrate Co.; and several officials and engineers from the Anaconda, Kennecott, and Bethlehem Steel companies&apos; mines in Chile.

Jan 1, 1942

By Carls Benedicks

It is well known by every one who has had to deal with boiler tubes that these are often seriously affected by a sort of corrosion, occurring as a local pitting, that frequently causes a perforation of the tube in a rather short time. The characteristic appearance of this corrosion is shown in Fig. 1. A very similar corrosion occurs in condenser tubes (Fig. 2).l A study of the microstructure or local chemical composition of the metal (iron 70:30 brass) fails to reveal any cause for this pitting. Of course one might possibly assume the starting point to be some oxide particle, causing an electrolytic local action, but this in no way explains the continued corrosion, progressing even when the assumed oxide particle must have disappeared. By the excellent work done by the Corrosion Research Committee of the Institute of Metals, and communicated, in October, 1923, to the Institution of Engineers and Shipbuilders in Newcastle-on-tyne, stress was laid on the faot that a content of entangled air has a very obnoxious effect. In the following correspondence, Sir George Goodwin stated that "engineers have, for a long time past, regarded air as the big enemy to be fought against in all questions of corrosion&apos;72 and Kenneth Fraser pointed out that the most vital point is "the avoidance or removal of possibly the chief cause of present day corrosion, i. e. entrapped air and gases brought out of solution."3 In their reply, however, the authors state that they had "never for a moment believed that entangled air was responsible for the beginnings of corrosion, and express the opinion that the gradual liberation of air could not account for localized corro~ion."~ On consulting the many textbooks on corrosion, as that

Jan 1, 1925

By P. H. Wendland

Calculations are presented for the design of a silicon photodiode in which the incident light beam makes multiple passes between the detector surfaces. Total internal reflection is used for this "light-trapping" effect. By this means, the optical path length can be extended to several millimeters, while the electrode separation remains less than 102 cm, as required for nanosecond response time. Data are presented for a Schottky barrier photodiode constructed on a multiply reflecting silicon base wafer. It is shown that the long-wavelength response is considerably extended in such structures without a corresponding sacrifice in high-speed response. The development of efficient and powerful lasers at 1.06 p has stimulated interest in detectors which operate at this wavelength. In typical silicon photodiodes, for detecting 1.06 p radiation, the requirements for high speed and high sensitivity are mutually exclusive. Since the absorption coefficient is only 25 cm-&apos;, a lo-&apos;-cm path length is required to absorb 92 pct of the incident 1.06 p radiation. If the electrode separation is greater than 10 cm, however, the carrier transit time will be greater than 1 nsec. This problem can be solved by allowing the incident light beam to make multiple passes between the electrodes. The optical path length can then be extended to several millimeters, as required for complete absorption, while the electrode separation remains less than 10&apos; cm, as required for nanosecond response time. In a typical photodiode geometry, one ohmic contact and one rectifying contact are formed on the two opposite surfaces of a base wafer, and the wafer thickness determines the electrode separation. The objective of the multiple reflection design is to allow all 1.06 p radiation to enter the detector front surface and to form the back detector surface so that no 1.06 radiation can exit. Total internal reflection at the back detector surface is well-suited for light trapping of 1.06 p radiation because the relatively large dielectric constant of silicon leads to a critical angle of 16.5 deg for total internal reflection. LIGHT TRAPPING It is well-known that, as light passes from one medium such as air into another medium such as glass or silicon, the angle of refraction is always less than the angle of incidence. In the limiting case, where the incident rays approach an angle of 90 deg with the normal, the refracted rays approach a fixed angle +, beyond which no refraction is possible: this is called the critical angle. It follows from Snell&apos;s law that where = critical angle, n - index of refraction of air, n&apos; - index of refraction of the medium. Applying the principle of reversibility of light rays, all internal angles of incidence greater than +, will produce total internal reflection and "light trapping". The index of refraction of silicon at 1.06 p is 3.5,&apos; and the critical angle is thus 16.5 deg. Fig. 1 shows these relationships for silicon. This very small critical angle in silicon is significant because all incident angles between 16.5 and 90 deg will produce total internal reflection and "light trapping". This effect can be implemented with a "prismlike" geometry, so that incident light can be introduced into the sample without loss and "trapped". PHOTOSIGNALS A precise knowledge of the absorption coefficient at 1.06 in silicon is of critical importance to the design of fast and efficient silicon photodiodes for 1.06 radiation. Dash and newman2 show a value of 25 cm-l, and our measurements have corroborated this value. Assuming that the collection of photoinduced minority carriers is perfect, the quantum efficiency of a photodiode is dependent only on the absorption coefficient. It then follows from Lambert&apos;s law that where QE is the quantum efficiency in pct, a is the absorption coefficient, d is the optical path length, and the reflectivity at the surface is assumed to be completely suppressed by an optical interference layer. Fig. 2 gives the maximum quantum efficiency for 1.06p radiation of a silicon photodiode with optical path length d, using Eq. [2]. The ultimate response time of a fully depleted photodiode to an incident light pulse can be considered to be the arrival times of all photoinduced carriers at the contacts, i.e., the minority carriers at the junction interface and the majority carriers at the oppo-

Jan 1, 1968

By E. A. Kaarsberg

The electron photomicrographs shown in this paper are of samples of the A.P.I. Reference Clay Minerals Montmorillonite No. 27 and Kaolinite No. 4 and of a shale from Spraberry Oilfield in Texas. These samples are part of a larger collection whose physical properties, composition and internal structure were previously studied by ultra-sonic and X-ray methods. &apos; Elastic anistropy was indicated in the montmorillonite and shale samples by sound velocity measurements parallel and perpendicular to the bedding. In the montmorillonite the velocities parallel and perpendicular to the bedding were 2.12 and 1.92 km/sec respectively, a difference of about 11%; in the shale the same velocity measurements were 4.18 and 3.75 km/sec, a difference again of about 11%. Within the bedding plane the sound velocity was also found to be independent of direction. The electron photomicrographs of the montmorillonite sample, which are shown in Fig. l(a) and (b), clearly indicate the preferred orientation of the mica-like clay particles parallel to the bedding. In Fig. 2(a) and (b) similar orientation in the shale sample can be seen although not quite as clearly. This is probably because, in addition to the clays illite and chlorite, the shale sample contains grains of quartz, calcite and dolomite which do not as readily show an alignment pattern as the clays do. This suggests that the elastic anisotropy of these two samples is derived from a preferred alignment of component mineral grains which are themselves elastically anisotropic. The bulk elastic properties of these two samples therefore appear to be much like those of mica. Velocity measurements were made on the kaolinite sample in three directions at right angles because no bedding could be discerned in it. The values ob-

Jan 1, 1967