Search Documents

By John Stewart

The market at present supplied by shipments from the phosphate districts of Quebec, Ontario, and New York State requires high-grade ore, carrying from 75 per cent. to 90 per cent. of phosphate of lime. In sorting out such material by hand, much valuable phosphate is necessarily left in the "culls" or refuse, besides which, much phosphate-rock of low-grade is not now mined at all, because it cannot be made available by the crude method of cobbing and hand-sorting. The utilization of such material, which would, of course, greatly benefit this industry, requires either a mechanical separation or a chemical process which would concentrate the phosphate in a form suitable for agriculture. Considering the rich phosphate now shipped as the first class, we may arrange the lower grades in three classes, as follows: Second Class.—Cull-ore from the first class, and the mass of deposits having, as gangue, pyroxene or hornblende. The following table gives the hardness and specific gravity of the minerals concerned: Hardness Spec. gravity. Apatite,....... . 5 3.1 to 3.25 Crystalline limestone (pink calcite),. 3 to 4 2.5 to 2.9 Pyroxene,..5 to 6 3.23 to 3.5 Hornblende,.5 to 6 2.9 to 3.4 Feldspar (orthoclase),. .. . 6 to 6.5 2.5 to 2.6 It is evident that when pyroxene and hornblende are present in large proportions, this ore cannot be successfully concentrated by crushing and jigging. It may be reduced to fine powder by successive treatment in a rock-breaker and a Sturtevant or Frisbee-Lucop mill, or other suitable apparatus, and in this condition it could be largely used by applying it freely upon exhausted clay soils, such as occur in Quebec and Ontario. The occupants of these once fertile river-lands are, however, hard to move in the direction of such improvements. When water-power is at hand, the cost of crushing

Jan 1, 1893

By Richard F. Miller

Recent studies of creep have made it apparent that plastic deformation may occur in metals under stresses less than the elastic limit as determined from short-time tests. In summarizing conclusions drawn from creep tests by various investigators, Tapselll said: "It is evident that if a material has a true elastic range, the elastic limit must represent the maximum stress for no creep." The presence of a definite elastic limit, represented in single crystals by a critical or threshold shearing stress, is claimed by Schmid2, Elam3 and others who have investigated the plastic deformation of single crystals. However, this "law of critical shearing stress" was determined2 from short-time tests, and the measurement of the deformation was made with apparatus primarily designed to observe large amounts of plastic deformation, not to detect elastic changes. Experimental data recently obtained with highly sensitive instruments by A. W. Hanson4 on zinc and by Podaschewsky5 on rock salt indicate that the elastic range in single crystals is considerably narrower than formerly was supposed. Moreover, a theoretical possibility of permanent deformation, under the influence of even the smallest shear stress in single crystals above a certain temperature (Td), has been developed by G. I. Taylor6. This evidence seemed to warrant an examination of the elastic limit in large single crystals by means of creep tests. The first metal chosen for examination was zinc. AppaRatus The creep-testing apparatus developed for this work is shown in Figs. 1 and 2. The extensometer A is sensitive enough to detect changes in length of 3.3 X 10~6 in. per in., and yet can be used into the plastic range without injury to the apparatus. The specimen,

Jan 1, 1936

By S. Lipson, H. W. Antes, H. Rosenthal

A study was made of the effect of ingot structure on the strength and ductility of high-strength wrought-aluminum alloys. It was found that a fine-cast structure facilitated complete homogenization which, in turn, resulted in significant increases in ductility and strength. A completely homogenized 7075-T6 alloy developed tensile properties of 85,000 psi UTS, 75,000 psi YS, with 40 pct RA. Completely homogenized 7001-T6 alloy tensile properties were 102,000 psi UTS, 99,000 psi YS, with 19 pct Ra. A method was devised for making small ingots having secondary dendrite arm spacing of less than 10 u. This method involved multiple-pass arc melting of commercial rolled plate with a tungsten electvode. This material could be completely homogenized after 3 hr at 900°F; homogenization of the original plate material was not complete after 120 hv at 900°F. Degree of homogeneity was determined by use of metallographic and electron-microprobe analyses. The electron-micro-probe study also showed the preferential segregation of solutes in the microstructure. HIGH-strength aluminum alloys, such as those of the 7000 series, usually freeze by the formation and growth of dendrites. The dendrite arm spacing (DAS) depends on the rate of solidification.' Commercial ingots are usually direct chill-cast to promote more rapid solidification, but, due to the large mass of the ingot, localized solidification times are long and a large DAS results. During solidification, solute elements are rejected by the solid as it forms, causing enrichment of the liquid and ultimately solute-rich interdendritic regions. In order to attain a homogeneous ingot, the segregated solutes must diffuse across the dendrite arms. The larger the DM, the longer the time for complete homogenization. In the case of commercial ingots, the DAS is so large that the time for complete homogenization is prohibitively long and, therefore, second phases or compounds are always present. These un-dissolved phases are carried over to the wrought material during processing, resulting in an impairment of strength and ductility. In addition, the mechanical fibering of the undissolved second phases or compounds during working results in mechanical property anisotropy. If complete homogenization could be attained, higher ductility could be expected. The realization of higher ductility at current strength levels is a desirable objective; however, if higher-strength alloys were wanted, it might be possible to sacrifice some of this ductility by adding more solute elements and produce even higher-strength alloys than are currently available. Further, if complete homogenization leads to more efficient utilization of solute elements, then more dilute alloys should have relatively high strengths with very high ductility. In all instances, it would be expected that the degree of mechanical property anisotropy due to mechanical fibering would be reduced. Therefore, it was the purpose of this investigation to produce cast structures that would facilitate homogenization and to determine the effect of homogenization on the properties of high-strength, wrought-aluminum alloys. MATERIAL CLASSIFICATION Commercial Alloys. In order to illustrate the non-homogeneous condition that exists in commercial high-strength, wrought-aluminum alloys, typical micro-structures of 7001, 7075, and 7178 are shown in Fig. 1. The chemical compositional specifications of these alloys are given in Table I. It can be seen in Fig. 1 that a considerable amount of undissolved second-phase material is present in each of these alloys. The solute elements associated with the undissolved phases were identified by electron microanalyses. Back-scattered electron images and characteristic X-ray images of the three commercial alloys are shown in Figs. 2, 3, and 4. These data indicate that the second phases are regions of high copper and high iron-copper concentrations. The second-phase material also was analyzed for magnesium, zinc, manganese, chromium, and silicon, but no significant enrichment above that of the matrix was found. Therefore, the problem of homogenization resolved itself into one of dissolving the copper-rich and the iron-copper-rich second phases. In order to accomplish this objective, two approaches were made. The first was to reduce the iron as low as possible since this element has a maximum solid solubility of 0.03 pct in aluminum. The second was to produce cast structures with finer DAS to facilitate dissolving the second phases. Commercially Produced High-Purity Alloys. A special high-purity, 2000-lb ingot of 7075 alloy was made by a commercial producer. This alloy contained the following weight percentages of solutes: 5.63 Zn, 2.48 Mg, 1.49 Cu, and 0.21 Cr. All other elements combined were less than 0.02 pct by wt including iron and silicon at less than 0.01 pct each. The ingot was cast and processed into rolled plate using standard commercial techniques. Microstructures of standard commercial 7075 and the special high-purity 7075 are shown in Fig. 5. It can be seen from this figure that the high-purity alloy has less undissolved second-phase material, but a significant amount was still present. The second phase in the high-purity material did not contain iron but it was found to be enriched with copper. The slight effects of the increased purity and de-

Jan 1, 1968

By K. F. G. Hosking

I read Professor Gaudin&apos;s paper with great interest and pleasure because for some time I have held that the chemical aspect of comminution is a subject of considerable importance to the mineral dresser and deserves to be thoroughly investigated. It does seem appropriate, however, to emphasize the fact that "fresh" edges and corners produced by the grinding of solids display enhanced reactivity has been recognized and utilized in the development of certain mineral identification techniques. Some of these techniques are worth noting, not only because they might facilitate research in the aspect of mineral dressing under discussion, but also because they emphasize the fact that many mineral species commonly regarded as being very inert can display a surprising reactivity when in the freshly ground state. In 1951 Isakov6 published a number of tests for the components of certain mineral species which depend essentially on grinding in a mortar a mixture of the material under investigation with a solid reagent. Thus when stibnite, 4(Sb2S3), is ground with sodium or potassium hydroxide. the antimony is revealed by a momentary development of a yellow color which changes in air to orange-red. Other antimony minerals need a preliminary treatment before the test can be carried out. This consists of grinding with aluminium sulfate, ferric sulfate or potassium bisulfate, and breathing upon the resultant mixture. I have employed a similar technique to determine the approximate magnesia content of certain limestones.&apos; The method depends essentially on the fact that when a sample of limestone is ground under controlled conditions with solutions of sodium hydroxide and Titan yellow the color of the final product is, within limits, a function of the amount of magnesia present. I have also shown that the components of a wide range of minerals can be identified by applying chemicals to their streaks on portions of vitrified, unglazed floor tiles, etc. Under such circumstances the diversity of the reactions which take place in the cold (because of the reactivity of fresh corners and edges) is surprising. Thus, for example, if a garnierite, (Ni,Mg)3Si2O5(OH)1, streak is treated first with a drop of 0.880 ammonia and then with a drop of a 1 pct alcoholic dimethyl-glyoxime it immediately becomes red, indicating the presence of nickel.&apos; Stevens and Carron9 have evolved a simple field test for distinguishing minerals by "abrasion pH." A soft nonabsorbent mineral is scratched in a drop of water on a streak plate until a milky suspension is formed. A piece of pH indicator paper is dipped into the suspension, after which it is removed and the maximum deviation from neutrality noted. When a hard mineral or one which absorbs water is being tested, fragments are first ground for 1 min with a few drops of water in a mortar to make a heavy suspension. The importance of the findings of such tests to mineral dressing may be judged by the abrasion pH values, Table 11, recorded by Stevens and Carron for certain species usually regarded as comparatively inert. The combined results Of the above researches clearly indicate that comminution is capable of altering the pH of a pulp and of causing the chemical nature of the surfaces of some of the components to be profoundly changed&apos; Depending On circumstances such surface alterations may have a beneficial or an adverse effect if these products are subsequently subjected to flotation. The tests also suggest that by grinding "inert" minerals with appropriate solid or liquid reagents "reactive" surfaces may be developed which might facilitate separations by flotation. It is an interesting and instructive problem to determine the reactions that are likely to take place when dry solid substances are subjected to comminution and to the unavoidable heat liberated during the process. To do this it is theoretically necessary to know the free energy values of the reactants and possible resultants, but unfortunately there is a dearth of such data! However, the heats of formation of many substances are known, and generally speaking, if in a reaction of the type AB + CD = AD + CB the sum of the heats of formation of AB and CD is less than that of AD and CB the reaction will probably proceed to the right. Thus, according to a note I have (the author of which I cannot name) if PbS (black) is warmed with CdSO, (white), PbSO., (white) and CdS (yellow) are formed, and that the reaction does, in fact, take place is indicated by the change in color of the mixture. The reaction is expected, as the sum of the heats of formation of PbS and CdSO, is less than that of PbSO, and CdS (as shown below). PbS + CdSO4 = PbSO4 + CdS 22.2 + 218.0 < 216.2 + 33.9 Finally, certain other aspects of the chemistry of comminution, which are neither mentioned by Professor Gaudin nor referred to by me are to be found in a paper by Welsh" and in the printed discussion thereof. A. M. Gaudin (author&apos;s reply)—The observations contributed by Dr. Hosking are indeed welcome, as they add to our experimental knowledge of a topic which is believed to be of the first importance. In connection with the experiments cited it should be kept in mind that oxidation, hydration, and carbonation at various rates should always be deemed to be possibilities when grinding is done in water or in air, even in "industrially dry" air. Special precautions might lead to sufficient minimizing of these reactions and to the assertion, instead, of deliberately-created reactions. The author wishes to thank Dr. Hosking for his contribution.

Jan 1, 1957

By D. J. Coolidge, H. L. Sheakley

THIS paper does not deal with all sands used in the glass industry in Missouri; it covers only that used in the plate-glass factory at Crystal City. However, it is probably safe to say that other sands, produced throughout the state for this purpose, are of identical nature. The glass sand used in Missouri is commonly called the St. Peter deposit, which is ascribed to the Ordovician Rock series in the form of sandstone. This St. Peter deposit, aside from a few small outliers, covers a large area of eastern Missouri. It forms, through a broad curve, the northeast margin of the typical Ozark region between Cape Girardeau on the southeast and Mineola, Montgomery County, on the northwest. The belt is extremely irregular, varying from one to ten miles in width; its length is 150 miles in a straight line. The outcrop near the entrance to the Crystal City mine appears in the form of a sandstone bluff approximately 30 ft. high, running along Plattin Creek (Fig. 1). Above the sand rock an overburden of Joachim limestone appears, which thickens to nearly 300 ft. and forms the hill commonly called Buck Knob. Test holes where drilled at various points and the drillers&apos; log indicate that the St. Peter deposit ranges in thickness from 63 to 71 feet. PROPERTIES OF THE ST. PETER SAND From an analysis of the glass sands of the St. Peter formation in Missouri, the follow-

Jan 1, 1942

By J. Campbell

The negative pressure developed within a solidifying sphere of pure iron is investigated theoretically assuming an elastic-plastic model. The maximum hydrostatic tension attainable is shown to be an order of magnitude smaller than that required for the homogeneous muclealion of pores in the liquid cove, and four orders of magnilude smaller than that predicted from) a rigid shell model. It is well-known that liquids can withstand large hydrostatic tensile stresses, or negative pressures. The various experimental investigations of the tensile strengths (often called the fracture pressures) of liquids are reviewed by Dean,1 and the theoretical attempts at estimating fracture pressures are critically assessed by wakeshima.2 Using Fisher&apos;s3 quation, the fracture pressure of pure liquid iron is about -70,000 atm, which may be too large by as much as a factor of 4, but is certainly correct to within an order of magnitude.&apos; In view of the great importance of the problem of the nucleation of shrinkage cavities in castings it is of interest to determine exactly what tensile stresses can exist in the residual liquid in a solidifying casting; it has often been assumed that, because of the very low strengths of solid metals near their melting points, no interior stresses are developed at all. Nussey4 has determined theoretically the pressure in the liquid core of a solidifying metal sphere assuming that the solidified shell does not deform (i .e., is perfectly rigid), so that because of the contraction accompanying solidification (a) (about 3 pct for most metals) the progressive deposition of solid onto the inner surface of the shell causes the remaining liquid to be expanded to make up this difference in volume. This leads to a relation between the pressure P in the liquid, the initial pressure, PO, the bulk modulus of the liquid, K, and the inner and outer radii of the solid shell, o and b, respectively:

Jan 1, 1968

By Arthur Notman

IN VIEW of the wide publicity given to the charges by the Couzens Committee of the United States Senate of discrimination by the Bureau of Internal Revenue in favor of the copper companies, it becomes a matter of interest to consider the basis for these charges. The point to be determined is whether they rest on a foundation of fact or are purely and simply matters of opinion. The whole question boils down to the purpose of the Tax Law as applied to mines, which is to afford the same protection to them as provided for all other taxpayers, namely: that they were to be allowed to pay back as depletion to their owners the values of their properties as they existed or were estimated to exist on May 1, 1913, free from tax. To determine these valuations it was? necessary to select from a wide range of possibilities a set of values for a number of essential factors.

Jan 1, 1925

By Willis T. Burns

I. Introduction.......................................... 703 II. History................................................ 703 III. General Description of Plant......................... 704 IV. AnoDes................................................. 711 V. Cathodes............................................... 714 VI. Electrolyte............................................ 718 VII. Electrolytic Slime..................................... 727 VIII. Power................................................. 728 IX. Operating Details..................................... 732 X. Furnace Refining...................................... 736 XI. Physical Testing oF Products.......................... 739 I. Introduction. These notes are submitted, not as a discussion of the modern practice of electrolytic-copper refining, but as the record of a refinery that was among the pioneers in the field and that is to-day, and has been for 17 years, operating under conditions not to be found in any similar plant in the country. I refer to the current density, which is at least 60 per cent. higher than that regularly employed elsewhere, and to the fact that the anodes treated are the direct product of the converter rather than of the reverberatory furnace. The writer has no knowledge of any other refinery treating anodes of this character. II. History. This refinery, now one of the oldest plants of its kind operating in this country, was built in 1892 by the Boston & Montana Consolidated Copper & Silver Mining CO. to refine the product of its Great Falls reduction works. The estimated capacity of the plant as designed was 65,000 lb. of cathodes per day at a current density of 16 amperes per square foot.

Jan 1, 1914

By Alexander Deussen

The figures listed in a table for Gulf Coast fields given by L. P. Teas1 in 1934 are so greatly at variance with results that I have obtained from a serious study of this subject over a number of years, that I am disposed to challenge the correctness of Mr. Teas&apos; figures as an accurate representation of acre-foot yields of Gulf Coast fields, and as regards at least two of the fields listed by Mr. Teas I desire to "put into the record" some figures that, according to my study, are more nearly in accord with what I conceive to be the actual facts. Upon investigation I find that Mr. Teas&apos; figures, inadvertently no doubt, arc not what they purport to be. Apparently the figures were arrived at by considering as thickness of the producing formation the net thickness of producing rock corresponding "to the total of the net portions of the producing zones which actually yield oil into the drill hole"—and in following this method I am under the impression that Mr. Teas was acting under instructions of the Institute in the preparation of this paper, in order to get comparable figures from the several fields of the United States. Apparently the author interpreted these instructions to mean that in the absence of cored thicknesses of producing horizons the actual number of feet of screen set in the various producing zones was to be taken as the basis for arriving at the thickness of these zones and the "acre-foot" yields. It is obvious that in many instances only 20 ft. of screen, or even 10 ft. of screen, might be set in a well, when there might be actually 100 ft. of oil sand present. In the early operations in the Gulf Coast it was usual to set much less screen than the amount of sand. It follows that the "acre-foot yields" so arrived at would be much greater than those found by using the full amount of sand. In Mr. Teas&apos; table, it was indicated that up to the end of 1933 "acre-foot" yields had been obtained in the several fields as listed in Table 1. A casual inspection of these yields will show that certainly they do not properly reflect the amount of oil produced from an acre-foot of the

Jan 1, 1936

By Alexander Deussen

The figures listed in a table for Gulf Coast fields given by L. P. Teas1 in 1934 are so greatly at variance with results that I have obtained from a serious study of this subject over a number of years, that I am disposed to challenge the correctness of Mr. Teas&apos; figures as an accurate representation of acre-foot yields of Gulf Coast fields, and as regards at least two of the fields listed by Mr. Teas I desire to "put into the record" some figures that, according to my study, are more nearly in accord with what I conceive to be the actual facts. Upon investigation I find that Mr. Teas&apos; figures, inadvertently no doubt, arc not what they purport to be. Apparently the figures were arrived at by considering as thickness of the producing formation the net thickness of producing rock corresponding "to the total of the net portions of the producing zones which actually yield oil into the drill hole"—and in following this method I am under the impression that Mr. Teas was acting under instructions of the Institute in the preparation of this paper, in order to get comparable figures from the several fields of the United States. Apparently the author interpreted these instructions to mean that in the absence of cored thicknesses of producing horizons the actual number of feet of screen set in the various producing zones was to be taken as the basis for arriving at the thickness of these zones and the "acre-foot" yields. It is obvious that in many instances only 20 ft. of screen, or even 10 ft. of screen, might be set in a well, when there might be actually 100 ft. of oil sand present. In the early operations in the Gulf Coast it was usual to set much less screen than the amount of sand. It follows that the "acre-foot yields" so arrived at would be much greater than those found by using the full amount of sand. In Mr. Teas&apos; table, it was indicated that up to the end of 1933 "acre-foot" yields had been obtained in the several fields as listed in Table 1. A casual inspection of these yields will show that certainly they do not properly reflect the amount of oil produced from an acre-foot of the

Jan 1, 1936

By P. Duwez, C. B. Jordan

A. J. SHALER*—I should like to congratulate the authors for having carried out such a precise set of experiments. It has been found useful, in sintering experimental compacts in vacuo, to make certain that the residual gas is not one which reacts with the metal. Since traces of oxygen can be kept away only with great difficulty, the technique is often adopted of using a "getter " of powder in the vicinity of the compacts, and, in addition, of permitting a small hydrogen leak to flow into the vacuum chamber. Did the authors use similar devices? This paper brings up a question concerning the definition of the word &apos; sintering.&apos; The authors restrict its use to the adhesion between particles. Kuczynski, in a paper presented at this meeting, applies the word to the growth of areas of contact between particles. I have used it to mean both these phenomena and also the dimensional changes which continue to take place after the first two have run their course. May I suggest that we should come to an agreement on the use of these words ? Fig 1 and 2 show an interesting feature: extrapolation of the curves to zero time does not give a densification parameter of zero. The higher the temperature, the higher is the intercept on that axis. These observations agree with the concept of a practically instantaneous densification taking place while the compact is being brought to heat. Such a change may be brought about by plastic deformation and primary creep. The stress pattern causing this first rapid flow is, to my mind, due to the force of attraction between the surfaces of opposite particles in the regions immediately flanking their common areas of contact. The stress is not temperature-sensitive, but at room temperature plastic deformation only proceeds until the metal in the area of contact can support it elastically. As the metal is heated, the elastic limit falls, and further plastic flow occurs. At the higher temperatures, this is followed by primary creep, and finally by the steady-state rate-reaction which the authors are seeking. If they were to recalculate their densification-parameter values, using, not the initial density of the cold compact, but the density after the compacts have been brought to temperature, the systematic deviations from linearity in Fig 3 and 4 might be eliminated. Such initial densities might be obtained by extrapolating the curves of Fig 1 and 2 to zero time. I am naturally pleased to see that such a very well done series of experiments leads to a heat of activation (for the densification process in hydrogen) that is much higher than that for self-diffusion, in confirmation of the less elaborate results reported by Wulff and myself (Ind. and Eng. Chem., (1948) 40, 838). J. T. KEMP*—I would like to comment on Dr. Shaler&apos;s remarks. There are apparently different interpretations of the word "sintering." It seems to me that an accurate definition of our word is essential in all metallurgy. May I point out, in this connection, that in practical metallurgy the word "sintering" has been applied to a bonding process in the preparation of ores and flue dust for fur-nacing. It would be unfortunate if in the area of powdered metallurgy we should establish a definition that is essentially different in meaning. F. N. RHINES*—I think that I can answer the question by saying that I see no essential difference between the use of the term "sintering" in extractive metallurgy and in powder metallurgy; physically the same things are going on. I admit sintering is used for different end purposes in the two cases. When we resort to the sintering of lead ore mixture we are doing so to obtain a chemically reactive, loose texture of some rigidity. This is only a difference in use. After all, in powder metallurgy we sometimes deliberately produce a very porous material which has just a little strength, just as in the case of sinter cake. P. DUWEZ (authors&apos; reply)—We agree that it would be helpful to have well-established definitions of such terms as "sintering." Since the question has now been raised, the time might be appropriate for its consideration by some suitable committee of one or more of the metallurgical societies. In answer to Dr. Shaler&apos;s first question, no getter nor hydrogen leak was used in our vacuum experiments, except insofar as the guard disks (used to reduce friction between specimens and trays) may have acted as getters. Dr. Shaler&apos;s statement that extrapolation of the curves of Fig 1 and 2 does not lead to zero densification at zero time apparently overlooks the logarithmic

Jan 1, 1950

By M. C. Fuerstenau, R. B. Bhappu

The response of beryl to sulfonate flotation was examined. The dependence of flotation recovery on sulfonate concentration, pH, and the absence or presence of various ions is also demonstrated. The response of quartz and feldspar to sulfonate flotation at various values of pH is given to. show the conditions necessary for selective separation. Finally, beryl was successfully concentrated from a natural ore using a technique devised from experimental observations on systems of pure minerals. With the possible exception of quartz, the flotation characteristics of silicate minerals are rather poorly understood. This is due in part to the com- plexity of the mineral systems themselves and in part to an insufficient amount of flotation data. The complexity of the systems arises from the wide range of chemical composition that the silicate minerals can assume. This is reflected in the variability of such physical properties as hardness and cleavage. Although the chemical composition of silicate minerals can vary considerably, a general grouping can be accomplished conveniently on the basis of the assemblage of SiO4 tetrahedra in all the silicates. That is, it has been shown that six basic groups can be obtained, depending on the arrangement of oxygen sharing between adjacent silicon atoms (or substituted aluminum). When all four oxygen atoms are shared, a framework structure such as quartz or feldspar is obtained. When three oxygens are shared, infinite sheets are obtained as in the micas and clays. When two oxygen atoms of the tetrahedra are shared, infinite chains are obtained, such as those in

Jan 1, 1963

By H. L. Gilbert, C. T. Anderson, W. J. Kroll

In a previous paper,&apos; the use of a split graphite tube resistor as a heater element for high-temperature furnaces has been described. The principal advantages of this type of construction are: I. The quadruple resistance or voltage compared with the top-bottom clamp resistor furnace. 2. Free expansion of the resistor. 3. The ease of protection from oxidation by air. 4. The firmness by which it may be held in the compact split clamp. This construction appeared to be well adapted for the fusion of high melting metals which require fusion in a vacuum. Zirconium metal had previously been melted at the Albany Laboratory of the Bureau of Mines in a vacuum arc furnace on a water-cooled plate, using a movable tungsten top electrode.% When larger furnace capacities were desired, this type of construction proved to have its limitations as the largest tungsten rods available were about 7/8 in. in diameter. The supply of direct current of high amperage for producing the desired arc characteristics was also not available. Considerable difficulty was also found in compensating the atmospheric pressure on the flcxible tubing of the movable electrodc, at the same time keeping its movement sufficiently free to enable the striking of an arc on any part of the metal briquet. Among the various materials used for the electrodes in conducting experiments in the vacuum arc furnace was graphite. It was found that zirconium fused in a graphite cup with a carbon arc was contaminated to only 0.2 pct carbon. It was therefore decsed to melt zirconium directly in graphite crucibles. A high-frequency furnace was first used in the attempt to melt the zirconium in graphite crucibles. The high-frequency heating coil was placed outside a silica tube which was evacuated by means of an oil diffusion pump backed up by a mechanical pump. The graphite crucible was thoroughly degassed at 19oo"C before use. Considerable difficulty was experienced in operating at such temperatures in vacuo because, as shown by Zintl,3 carbon vapor formed and reacted with silica accortling to the reaction: SiO² + C = SiO + CO. The silicon monoxide which is volatile at these high temperatures reacted with the zirconium, thereby contaminating it with silicon and oxygen. The presence of carbon monoxide was detected by means of a gas discharge tube placed in the vacuum system as indicated by the pale blue glow of the tube as soon as carbon vapor started to react with the hot silica. The reaction between the carbon vapor and hot silica was avoided by the use of split cylindrical molybdenum shields which were inserted between the graphite crucible

Jan 1, 1949

By Albert Stazicker

AT Climax the warehouse department operates as an independent unit similar to the mine and mill departments. It has the responsibility of receiving, checking, unloading, and storing all material and supplies delivered to the plant. In addition, the transportation of all supplies comes under the direction of the warehouse so that prompt delivery of supplies to all departments is one of its major functions. The transportation division operates heavy and light trucks, trailers, two large tractors, and two snowplows. In addition to delivering supplies it is also responsible for snow removal from the roads, hauling of sand and gravel for concrete and domestic coal to employees. and all miscellaneous work involving the use of tractors or trucks.

Jan 1, 1946

By Edwin Dudley Martin

DURING the past twelve years the iron and steel industry has made a major advance through the development of the continuous wide strip rolling mill. So far-reaching have been the results that not only has a better product been sold at a lower price but this improvement in quality has permitted manufacturers of products using steel to make important savings in the cost of fabrication. The net result has been a better product at lower cost to the consumer without reduction in either employment or of wages paid within the industry. That is why the iron and steel industry is proud of its attainment. Being a basic industry of strategic importance, such an advance in technology has had its effects on our internal economy, our standard of living, and our industrial power as a nation in both peace and wartime.

Jan 1, 1939

By F. A. Forward, J. Halpern

A new process for extracting uranium from ores with carbonate solutions is described. Leaching is carried out under oxygen pressure to ensure that all the uranium is converted to the soluble hexavalent state. By this method), alkaline leaching can be used successfully to treat a greater variety of ores, including pitchblende ores, than has been possible in the past. The advantages of carbonate leaching over conventional acid leaching processes are enhanced further by a new method which has been developed for recovering uranium from basic leach solutions. This is achieved by reducing the uranium to the tetravalent state with hydrogen in the presence of a suitable catalyst. A high grade uranium oxide product is precipitated directly from the leach solutions. Vanadium oxide also can be precipitated by this method. The chemistry of the leaching and precipitation reactions are discussed, and laboratory results are presented which illustrate the applicability of the process and describe the variables affecting leaching and precipitation rates, recoveries, and reagent consumption. THE extractive metallurgy of uranium is influenced by a number of special considerations which generally do not arise in connection with the treatment of the more common base metal ores. Perhaps foremost among these is the very low uranium content of most of the ores which are encountered today, usually only a few tenths of one percent. A further difficulty is presented by the fact that the uranium often occurs in such a form that it cannot be concentrated efficiently by gravity or flotation methods. In these and other important respects, there is evident some degree of parallelism between the extractive metallurgy of uranium and that of gold and, as in the latter case, it has generally been found that uranium ores can best be treated directly by selective leaching methods. It is readily evident that this parallel does not extend to the chemical properties of the two metals. Unlike gold, which is easily reduced to metallic form, uranium is highly reactive. It tends to occur as oxides, silicates, or salts. Two ores are of predominant importance as commercial sources of this metal: pitchblende which contains uranium as the oxide, U3O51 and carnotite in which the uranium is present as a complex salt with vanadium, K2O-2UCV3V2O5-3H2O. These ores may vary widely in respect to the nature of their gangue constituents. Some are largely siliceous in composition, while others consist mainly of calcite. Sometimes substantial amounts of pyrite or of organic materials are present and these may lead to specific problems in treating the ore. Further complications may be introduced by the presence of other metal values such as gold, copper, cobalt, or vanadium whose re- covery has to be considered along with that of the uranium, or whose separation from uranium presents particular difficulty. In general, there are two main processes for recovering uranium in common use today.&apos;.2 One of these employs an acid solution such as dilute sulphuric acid to extract the uranium from the ore. A suitable oxidizing agent such as MnO, or NaNO, is sometimes added if the uranium in the ore is in a partially reduced state. The uranium dissolves as a uranyl sulphate salt and can be precipitated subsequently by neutralization or other suitable treatment of the solution. The second process employs an alkaline leaching solution, usually containing sodium carbonate. The uranium, which must be in the hexavalent state, is dissolved as a complex uranyl tricarbonate salt, and then is precipitated either by neutralizing the solution with acid or by adding an excess of sodium hydroxide. The latter method has the advantage of permitting the solutions to be recycled, since the carbonate is not destroyed. This is essential if the process is to be economical, particularly with low grade ores. With each of these processes, there are associated a number of advantages and disadvantages and the choice between using acid or carbonate leaching is generally determined by the nature of the ore to be treated. In the past, more ores appear to have been amenable to acid leaching than to carbonate leaching and the former process correspondingly has found wider application. With most ores, acid leaching has been found to operate fairly efficiently and to yield high recoveries. One of the main disadvantages has been that large amounts of impurities, such as iron and aluminum, sometimes are taken into solution along with the uranium. This may give rise to a high reagent consumption and to difficulties in separating a pure uranium product. Excessive reagent consumption in the acid leach process also may result

Jan 1, 1955

By L. A. Bromley, A. W. Petersen

The van Arkel-deBoer method for producing ductile titanium by thermal decomposition of Til, vapor and deposition on an electrically heated filament is modified by film boiling Til liquid on a heated filament, resulting in similar titanium deposition on the filament and liberation of gaseous iodine. The deposition rate is higher and the energy requirement smaller than in the van Arkel process. Many problems must be solved before the process is commercially feasible. TITANIUM of 99.9 pct purity, called ductile titanium, has been produced by a modification of the van Arkel-deBoer&apos; method. In the van Arkel-deBoer method, an electrically heated wire is suspended from two electrodes, which are placed in a container holding TiI, vapor at a low&apos; vapor pressure (usually <5 mm Hg). The vapor diffuses to the hot wire, usually maintained at 1100" to 1600°C,&apos; and decomposes according to the reaction liberating gaseous atomic iodine and depositing solid crystalline titanium on the wire. Estimations based on the data of Runnalls and Pidgeon,&apos; indicate that the rate-control ling step is the diffusion of atomic iodine away from the wire. There appears to be nearly thermodynamic equilibrium at the wire with TiI, and iodine as the main gaseous species. TiI, is almost certainly an important gaseous species in the cooler regions.&apos; The liberated iodine diffuses to a heated source of crude titanium and reacts to form more TiI, vapor, which again diffuses to the hot wire and completes the cyclic process. The foregoing process may be modified by suspending the hot wire in liquid TiI,, instead of the vapor, and obtaining film boiling. This type of boiling is characterized by the formation of a continuous film of vapor over the wire surface. Since only vapor contacts the wire sul.face, the temperature of this surface may be raised as high as desirable, within the limit of mechanical strength requirements for the wire. By properly adjusting the input voltage. the temperature of the wire may be maintained above U0C"C; and by evacuating the vessel holding the liquid TiI, and maintaining a suitable condenser temperature, the vapor pressure of TiI, may be held low. Thus, the conditions of operation of the van Arkel-deBoer method may be approximated with film boiling; and hence, it is postulated that ductile titanium may be produced by this method. Preparation of Til, There are many methods available for the preparation of TiI,; that used in this research was prepared by the direct reaction of titanium sponge in controlled amounts with liquid iodine. Although no difficulty was encountered with this reaction, it has since been pointed out that this method is sometimes dangerous and should be used with caution. The resulting TiI, was purified by distillation. First Film Boiling Experiments Apparatus: The apparatus shown in Fig. 1 was used for film boiling TiI, on short wire filaments. The current to the filament was supplied through a bank of three 5 kva transformers connected in parallel. The current was controlled by adjusting the voltage over a 0 to 67.5 v range with a 7 kva variable transformer on the low voltage side of the bank of transformers. The current and voltage were measured by Weston meters. The sealed-in-glass tungsten electrodes were hard-soldered to the filament for the film boiling of TiI,. The bottom part of the reactor, containing TiI,, was wrapped with ni-chrome heating wires to maintain the TiI, in the liquid state. An ice or liquid nitrogen trap, for solidifying I, vapor and any TiI, not condensed, was attached to the low pressure side of the air-cooled condenser. A Megavac vacuum pump was used. Procedure: A 0.010 in. diam tungsten filament was hard-soldered to the tungsten electrodes. TiI, was melted (mp 156°C) and poured into the reactor chamber; the top of the reactor chamber, containing the electrodes, was replaced. Freezing of the TiI, was prevented by controlling the current to the ni-chrome wires wrapped around the reactor with a 1 kva variable transformer. The mechanical vacuum pump was started and the system evacuated to about 2 mm Hg TiI, vapor pressure. The current to the filament was turned on and the impressed voltage slowly increased with the variable transformer. A sudden drop in current at nearly constant im-

Jan 1, 1957

By D. C. Ganow, N. J. Grant, I. R. Silver, A. R. Chaudhuri

The structural changes that result when a metal is "cold worked" lead to higher values of yield and tensile strength on subsequent deformation at room temperature. Further it has been shown that the beneficial effects of cold work are, to some extent, maintained even at elevated temperatures. The strength improvements from prior cold work decrease as the temperature is raised and are a function of grain size, amount of cold work, and strain rate (or time of test). If recrystallization occurs during test, the cold-worked material may even show weaker stress-rupture properties than the annealed material. A question that arises is whether there is a significant effect on the subsequent creep behavior if the prior deformation is performed under creep conditions at high temperatures not too different than the test temperature, but at significantly different strain rates and for various amounts of strain. An answer to this question was sought in the work described in the present paper. PROCEDURE Two materials were used in this work, high-purity aluminum and a solid-solution A1 2 pct Mg alloy. The compositions are shown in Table I. The grain size in the two materials was 0.2 to 0.3 mm. The deformation for both the prestraining and for the creep tests was at constant stress. The procedure adopted was to prestrain a specimen to the desired elongation, remove the load, and cool to room temperature rapidly by spraying. the test bar with cold water. The specimen was then placed in a creep machine, held at the test temperature for less than 5 min, and loaded. Less than 15 min was required to bring the specimen to temperature. The creep stress was based on the diameter resulting from the prior strain, and values of elongation at fracture listed in the tables do not include the respective elongations resulting from the prestrain. The choice of the stresses for the prestrain and for the creep tests was made so that the tests could be completed in relatively short times to maximize any effect of prestrain. The specimens had a gage length of 1 in., the pure aluminum specimens having a diameter of 0.150 in. and the alloy specimens a diameter of 0.125 in. For pure aluminum, prestrain was at 400&apos; and 600°F with testing at 500°F; for the alloy, prestraining was at 700°F and testing at 600°F. RESULTS The prestrain conditions for the aluminum and the alloy specimens are shown in Tables I1 and IV. In addition to showing the time required to achieve the desired prestrain, the expected rupture Lives are given which would have resulted had the creep prestrain been continued to fracture. The prestrained and the annealed specimens were then tested in creep to fracture; the temperature and stress for the pure aliminum specimens being 500o F and 1800 psi and for the alloy, 600&apos; F and 3400 psi. The creep curves for the prestrained and the annealed specimens of pure aluminum showed all three stages of creep; hence in addition to the effect of prestraining on the rupture life, it was also possible to determine the effect of prestraining on the minimum creep rate, and on the time and elongation at the end of each of the three creep stages. The results are shown in Fig. 1 and Table 111.

Jan 1, 1960

By D. W. Levinson, L. E. Tanner

DURING the course of an investigation of the zirconium-iron-tin system the zirconium-iron system was reexamined up to 55 pct* Fe. The alloys pre- visible melting3 and X-ray diffraction studies were made of samples of the alloys. The ferromagnetic properties of ZrFe2were determined by Professor P. W. Selwood* using a modified Faraday balance.4 The zirconium-rich portion of the phase diagram is presented in Fig. 1 and compared with the work of Hayes et al.1 The maximum solubility of iron in ß is somewhat decreased while the eutectic temperature is raised. There seemed to be no change in the eutectic composition of 16 pct Fe. Since the base material was so low in iron content, it was possible to establish the maximum solubility in a between 0.017 and 0.025 pct Fe at the eutectoid temperature. The observation of fine ZrFe, particles in the micro structure of a specimen of 0.012 pct Fe alloy quenched from 700°C indicated that the solubility drops below this composition at 700° C and lower. Further study was made of the intermediate phase ZrFe2. wallbaum5 identified the compound initially as ZrFe2 with a C 15 (MgCu2) structure, placing it at 55 pct Fe stoichiometrically. Hayes et al.1 believed they found the phase at about 47.2 pct Fe and called it Zr2Fe3 but reverted to ZrFe, in the discussion of their paper.6 Jordan and Duwez7 confirmed Wallbaum&apos;s work as well as finding the same single-phase structure to about 62.3 pct Fe or Zr0-61 Fe2-18. In order to establish the ternary phase relations in the zirconium-iron-tin systema the exact position of this phase had to be known. This was accomplished by X-ray diffraction, visible melting, and metallographic techniques. Elliott8 obtained a single-phase ZrFe2 X-ray diffraction pattern from an alloy of about 55 pct Fe. This was confirmed in the present study with an alloy of 54.81 pct Fe. However, extra lines (attributable to a or ß zirconium) were found in diffraction patterns of the 47.42 and 49.83 pct Fe alloys. The melting characteristics of these same alloys were studied by suspending 47.42, 49.83, and 54.81 pct

Jan 1, 1960

By B. A. Cheadle, C. E. Ells

The ovienlalion of hexagonal a-zirconium crystals in cold-drawn Zircaloy-2 tubes and in both as-extruded and heat-treated Zr-2.5 wt pcl ND tubes has been rrleasured using the inverse Pole - figure technique. Uniaxial tensile tests hare shown the Zil-caloy-2 lubes to hare highly anisotropic delovmation behavior whereas heat-treated Zr-2.5 wt pet Nb tubes are nearly isotropic. The differences in deformation behavior are esbloilred from the observed textures of the tubes and the deformation systems known to oberate in Zircnloy,-3. Tlze vcsults lead to an explanation of the high effective strain observed fov the Zircaloy-2 tubes as colrzpared to heat-treated Zr-2.5 wt pet Nb tubes in restrained end burst tests at 280° to 300°C. THE Zr-2.5 wt pct Nb alloy. when heat-treated by quenching from temperatures slightly below the (a + p)/P phase boundary and subsequently aged at 500°C, has tensile strengths about 50 pct greater than those of 20 pct cold-worked Zircaloy-2.1 There is. therefore, considerable economic incentive to replace Zircaloy-2 with the heat-treated alloy in some in-reactor applications. notably for pressure tubes, where strength is a prime consideration. However, when tubes of Zr-2.5 wt pct Nb fabricated by extrusion and drawing prior to heat treatment were subjected to restrained end-burst tests at 300 °C. the circumferential expansion at failure1 was only 10 pct that of cold-drawn Zircaloy-2 tubes in similar tests,2 Table I. This result was not predicted from uniaxial tensile tests in which the ductilities of the two materials were quite similar.&apos; The detailed requirement for ductility in pressure vessels has not yet been worked out. and comparison of the relative merits of cold-worked Zircaloy-2 and heat-treated Zr-2.5 wt pct Nb is further complicated by the irradiation-induced loss of ductility and hydrogen pickup each will undergo from reactor operation.1,2 Nevertheless. the lower circumferential expansion of the Zr-2.5 wt pct Nb tubes raised serious doubts on the advisability of their use as pressure vessels. For this reason, an investigation to determine the cause for different ductilities of the two types of tubes was initiated. From a study of uniaxial tensile properties and crystallographic orientation it has been found that the fracture ductilities observed in the burst tests can be related directly to the crystallographic ori-

Jan 1, 1965