Search Documents

By Hollis L. Caswell

The present status of integrated circuits utilizing. superconductive switching. elements is reviewed with special attention given to fabrication techniques, methods for interconnecting completed circuits, and refrigeration requirements. Cryoelectronics has been largely an "inte- grated-circuit" technology since its conception because the switching speed of superconductive devices is attractive only when these devices are fabricated with thin-film techniques. It is true that cryotron circuits can be constructed from wires of appropriate materials (as indeed was done by Dudley Buck 1 in his early investigations) but these circuits will switch in times characteristic of milliseconds whereas similar circuits fabricated by thin-film methods have potential switching times of nanoseconds. Furthermore, cryo-electronic devices such as the cryotron lend themselves readily to fabrication by thin-film techniques since these components may be made from polycrys-talline thin films and are relatively insensitive to the presence of impurities (as measured by semiconductor standards). Therefore, during the past decade considerable effort has been devoted to developing techniques for batch fabricating circuit arrays containing superconductive switching elements. Technology had developed to the point several years ago that fabrication of cryoelectronic arrays containing up to one hundred devices was rather straightforward. However, larger arrays containing between lo4 and 106 components which are required for commercial development of cryoelectronics still pose very severe yield problems. Thus in a sense cryoelectronics found itself in 1962 at the point semiconductor technology finds itself today; namely, individual devices and small groups of integrated devices could be fabricated with acceptable yield and the outlook for building larger integrated-circuit arrays was bright. Unfortunately, problems associated largely with yield have made fabrication of these larger arrays difficult. Unlike semiconductor technology, cryoelectronics had to solve the problems of large-scale integration before it could become economically attractive. This has proven to be a sizable burden to bear. Since several reviews exist on superconductivity,2 superconductive devices,3 and cryoelectronic technology, no attempt will be made in this paper to summarize these areas. Instead a few specific topics will be dealt with in more detail. First, a brief description is given of selected superconducting switching and storage devices with special attention to several metallurgical techniques which improve the performance of these devices. Second, techniques used to fabricate cryoelectronic devices are described with emphasis on problems affecting yield. Third, techniques for interconnecting a number of cryoelectronic planes are described. And last, refrigeration of cryoelectronic components is discussed briefly since the low operating temperature of superconductive devices is an important consideration in this technology. SUPERCONDUCTING STORAGE AND SWITCHING DEVICES The basic superconductive switching device is the thin-film cryotron. The geometry of this device is attractively simple, since it involves only the intersection of two lines that are electrically insulated from each other. The switching element (gate) and control element (control) of a crossed-film cryotron are arranged as illustrated in Fig. 1. The material for the gate is selected to permit the gate to be switched from the superconducting to the normal (resistive) state by the application of a control current. Tin, which has a critical temperature (T,) of 3.7°K, is commonly used for the gate and the cryotron is operated at a temperature just below T, (for example, 3.5°K). The control material (normally lead, with T, = 7.2°K) is chosen so that the control is never driven normal during circuit operation. To improve cryotron operation, a ground plane, also of lead, is placed under all of the circuitry to act as a diamagnetic shield and improve the current-density uniformity across the width of various thin-film elements. Normally, line widths vary from 0.005 to ^ 0.020 in. and film thicknesses from 300 to 10,000A, although new fabrication techniques make narrower lines feasible. In fabricating cryotrons it is important that the edges of the gate elements be geometrically sharp to avoid undesirable switching characteristics associated with a thinner edge region, Fig. 2. One technique which has been used extensively to form patterns consists of placing a physical mask containing the film pattern between the evaporation source and the substrate and depositing through the mask. Film strips formed in this manner possess a penumbra at the film edges due to shadowing of the evapor-ant under the mask. Several techniques have been proposed for minimizing effects due to this penumbra. One of the more promising metallurgical techniques

Jan 1, 1967

By M. P. E. Desvaux, P. Charsley

OLIP-line observations on copper alloys, using the electron microscope, have been made by a number of workers,13 but this work has been confined to a brass. In a CuAl alloys Koppenaal4 and Koppenaal and Fine5 have made observations with the optical microscope and by the use of interferometry. They found that the observed slip step heights inside the Liiders bands accounted for only 42 pet of the total macroscopic strain. The suggestion was put forward that optically unresolvable slip in other parts of the specimen accounted for a major part of the macroscopic strain. This is surprising since it is known from other workers that slip in a brass is inhomogeneous; i.e., large amounts of slip occur on individual {lll) closelys paced than being shared by a large number of closely spaced planes. Furthermore, a brass and a CuAl alloys with high concentration of aluminum exhibit similar deformation characteristics and slip-line patterns. Prior to investigations into the behavior of copper and a CuAl alloys under reversed stresses in tension and compression, some preliminary experiments have yielded results which the authors think resolve this discrepancy, and throw some further light on the behavior of a CuAl in tension. An experiment was carried out on a 10 at. pet CuAl single crystal, of gage length 7.5 cm, diameter 3.1 mm, and orientation shown in Fig. 3 (inset), for the purpose of resolving the above discrepancy. The specimen gage length was electropolished for 10 min in a 50:50 orthophosphoric acid (SG=1.75)-distilled water system, with 2 v across the cell and a current density of 0.5 amp per sq cm. The cathode was made of copper. After a tensile strain of 0.067 ± 0.001, intense slip was observed over a length 2 cm of the gage length whilst the rest of the specimen was relatively undeformed. In the lightly deformed region, slip bands of mean width 20 /x were spaced about 1 mm apart on average. The transition from the heavily slipped region (usually called a Liiders band) to the lightly deformed region was gradual, the slip-band density increasing as the "Liiders band" was approached. In the latter, the slip bands became so close together that, to the naked eye, the specimen appeared to be continously slipped, and the typical microtopography of this region is shown in Fig. 1. Twelve electron micrographs were taken at random from replicas of the Liiders-band region, and the widths of the slip lines were measured. The slip lines account for an over-all tensile deformation of 7.0 ± 0.7 pet, after allowing for the lengths of the un-slipped regions, which is in good agreement with the macroscopic strain. The distribution of slip-line widths was also measured and is shown in Fig. 3. Since Koppenaal could not resolve slip lines with height less than 540A (limit of resolution represented by dashed line), then it was deduced that he could have measured only about 50 pet of the deformation within the 'Liiders Band'. It is concluded, contrary to the suggestion of Koppenaal,5 that virtually all the macroscopic strain is accommodated within the "Luders band" and that there is no need to invoke fine slip distributed uniformly over the gage length.

Jan 1, 1967

By C. C. Nitchie, G. S. Brooks

With the gradual depletion of the natural-gas pools of the Kansas district, together with the uncertainty of further cheap fuel developments, some of the western zinc companies turned to the coal fields, attracted by their permanency and the success of the Matthiessen & Hegeler Co. and the lllinois Zinc Co. Being then confronted with the problem of using a relatively high-priced fuel, although the ultimate supply was very great, the fuel economies of the kilns and furnaces became of far more importance, and the more modern equipments, as a result, embodied distinct gaias in this phase of the business. In addition, there have been some pronounced advances in the actual making of gas from these coals. Increased efficiency in gas making has contributed its hare to lowering costs and those plants located in the higher priced fuel districts have probably been obliged to study these economies somewhat more closely. Naturally, many beneficial changes have resulted in both practice and apparatus in these sections. On certain western coals, for instance, the actual saving in fuel consumption has been 50 per cent. By this is meant that, where about 1.75 tons were burned to smelt 1 ton of oxidized ore, 0.7 to 0.9 ton is now required. While comparisons by T. R. Ingalls1 of fuel economies in smelting in this country and Germany before the war may, in general, be correct, they do not appear to do justice to the more progressive American practice. It is doubtful whether German plants were substantially bettering these fuel ratios. Data furnished by Bender and Frams do not afford records averaging less than 0.9 ton coal per ton ore on materials from 40 per cent. to 50 per cent. zinc. Fuels As producer fuel, Illinois, Indiana, and Kansas coah offer a wide range of material, although varying much in their amenability to gasscation. The proper fuel for each plant can only be determined after com-

Jan 1, 1920

By R. G. O’Meara, M. M. Fine

ONE of the principal activities of the Bureau of Mines connected with the recent war was to help to increase the supply of strategic and critical minerals. Fluorite was one of the most critical of the nonmetallic minerals because of the increased demand for it as a flux in basic open-hearth and electric steel furnaces and as a raw material for the production of artificial cryolite used in the aluminum industry. Wartime developments in the technology of hydrofluoric acid, such as the use of the anhydrous acid as a catalyst in production of high-octane gasoline and the use of organic fluorides as carriers for insecticides, also increased the demand for acid-grade fluorite.[t] In 1943 the consumption of acid-grade fluorite was advancing at a more rapid rate than production, and was only slightly less than production during the latter half of the year.1 The outlook for the postwar market for fluorite is encouraging. Steel production is expected to remain high until the domestic demand for commodities not manufactured during the war is satisfied. The uses for hydrofluoric acid are expected to increase under the impetus of war-initiated research. In consideration of these and other factors some authorities predict a postwar demand for fluorite equal to about 60 to 75 per cent of the wartime production.1,2 Others believe that the postwar fluorite industry will be permanently expanded over its prewar status.3 ACKNOWLEDGMENT This paper is one of many reporting on various aspects of the Bureau of Mines program directed toward the more effective utilization of our mineral resources. The program has been under the general supervision of R. S. Dean, Assistant Director, since July 1942. The scope of the paper falls in the province of the Metallurgical Branch, whose activities embrace the separation of difficultly beneficiated ores, the production of pure metals from domestic deposits, the exploitation of marginal ore reserves, the recovery of secondary metals, and the improvement of present industrial metallurgical practice. The investigation was initiated at the request of Mr. J. H. Steinmesch, vice-president and general manager, Minerva Oil Co., Eldorado, Ill. His hearty cooperation and helpful suggestions, and those of Mr. O. E. Anderson, mill superintendent,

Jan 1, 1946

By J. L. Jones

1. Brinell tests at progressively increasing temperatures are given for a representative lead-base and a representative tin-base babbitt, showing that the former has superior resistance to deformation at the working temperatures of bearings. 2. Small squares of bearing bronze, tinned and then babbitted with a representative lead-base babbitt and a representative tin-base babbitt were subjected to compressive loading. The lead-base babbitt showed less average compression than the tin-base babbitt. Compression did not materially increase the Brinell hardness of the babbitts. 3. A process and a tool are described for giving smoother and more accurate surfaces to bearings than has heretofore been possible. The following experiments have recently been carried out in the chemical laboratory of the Westinghouse Electric and Manufacturing Co., Pittsburgh, Pa. While the work is incomplete, it is described at the present time because data on the comparative merits of lead-base and tin-base babbitts are of interest in connection with the present shortage of tin. BRinell Habdness of Babbitt at Increasing Temperatures Bearings fail because of wiping, or deformation. Hence tenacity is desirable in a bearing metal, especially tenacity at high temperatures. The Brinell test is commonly regarded as a measure of tenacity. In fact, it has recently been proposed to substitute for Brinell hardness number the expression " tenacity number."l It seemed, therefore, that the Brinell test was especially adapted for the tests described. Disks, 4 in. (101 mm.) in diameter and 1.5 in. (38 mm.) thick, were made of the babbitts to be studied, designated A, B, C. They were poured into metal molds, pyrometer leads being soldered in the center of each disk. The composition of the babbitts was as follows:

Jan 1, 1919

Map

Jan 1, 1939

By John Mathews

IT is twenty years since the writer made his first molybdenum steels and others were making them commercially five years earlier but the prevailing opinion seems to be that molybdenum steels are new; from time to time the daily press speaks of important discoveries in Europe and intimates that American steel makers have much to learn in regard to alloy steels. The earlier experiments were largely confined to the use of relatively high percentages of molybdenum in tool steels and permanent magnet steels. Recent developments deal with the types of alloy structural steels used for airplane, automobile, and other engineering requirements; in these, the molybdenum content is usually less than 1 per cent. The earlier types generally have been unsuccessful commercially, but the newer types of steels are becoming of increasing importance. The war showed our dependence on foreign sources for alloying metals; molybdenum alone is widely distributed in the United States and seemingly abundant. Many deposits are not now of commercial interest, owing to location and relatively small amount of ore available, but other deposits are being developed and a stable source of supply seems well assured. In tool and magnet steels, it was early found that 1 part of molybdenum was equivalent to from 2 to 2.5 parts of tungsten. The permanent magnet steels investigated by Madame Curie,1 in 1898, contained from 3.36 to 4.05 per cent. molybdenum; in 1902, Dr. E. L. French and the writer thoroughly tested steels containing from 2:0 to 4.0 per cent. These steels gave satisfactory tests for permanence, but were low in residual density and much more sensitive to hardening than the corresponding tungsten products. We discontinued work with them, therefore, and have no advice that such steels have been used commercially here or abroad.

Jan 2, 1921

By Nicholas J. Grant, Klaus M. Zwilsky

EVER since the unusual high temperature creep resistance and structure stability of SAP (Sintered Aluminum Powder) and similar aluminum-alumina alloys were reported,'," there has been a need to determine whether other metal-metal oxide (or other hard stable particle) alloys, not so ideal as the Al-Al 2 O 3 system, would show similar high temperature strength and stability. Of the many possible methods of obtaining a metal-metal oxide alloy,a one that offers many practical and theoretical advantages is the simple mechanical blending of metal powders with hard stable particles, followed by pressing, sintering, and hot extruding. With this purpose in mind copper powder and silica and alumina were selected for experimentation because these materials are readily available, cheap, reliable, and lend themseives te the simplest processing and testing. Starting Materials—Two sizes of electrolytically deposited copper powders were used, a —200 mesh powder referred to as A powder in this investigation and a —325 mesh powder referred to as C powder. Silica was added in the form of pure Potter's flint from which a —10µ fraction had been separated. Alumina of the a variety was used in two size ranges. The first was a —10µ fraction separated from a coarser aggregate, the second a commercial product of 0.3µ average diam manufactured by Linde Air Products. Preparation of Powders—Five-hundred gram batches of A copper with 1, 3, and 10 volume pct of each of the three oxides mentioned above were prepared, as well as C copper containing 1, 3, and 10 volume pct of —lop silica. Powders were weighed out carefully and blended by ball milling in air for 24 hr. Since this treatment resulted in surface oxidation of the copper, the charge was hydrogen reduced at 260°C for 5 hr. The next step consisted of hydrostatically compacting the powder into a shape suitable for the required hot working. For this purpose a slug about 11/2 in. in diam and 31/2 in. in length was produced by placing the mixed powders into a rubber sleeve, holding in a perforated steel canister, and rubber stoppering at the ends; the assembly was then subjected to a hydrostatic pressure of 50,000 psi. The air was evacuated from the assembly prior to pressing in order to prevent

Jan 1, 1958

By R. A. Meussner, C. T. Fujii

Chromium solution in wustite depresses the oxygen activity in a nonideal manner and expands the lattice slightly. Gravimetric measurements of the equilibrium compositions of wustite containing 0.00 to 1.38 wt pct Cr define the oxygen potential (CO2-CO atm) and the limits of the phase field at 1000°C. These data extrapolate to a maximum solubility of 2 wt pct Cr. The lattice parameter data, room-temperature measurements of quenched samples, differ significantly from those in the literature. Both pure and chromium wus-tites contract at uniform and equal rates as the oxygen content (metal deficit) increases. The a. US metal deficit relationships are straight lines showing none of the curvature previously reported. At constant metal deficit, the a. expands by 0.002? on alloying with 0.4 to 0.5 wt pct Cr but is insensitive to further chromium additions: a small expansion rather than a marked contraction. These results require a modification of the accepted alloying mechanism. IN the high-temperature oxidation of Fe-Cr alloys in Ha-H,and CO2-CO atmospheres the vapor transfer of oxygen from the continuous wustite outer scale to the porous inner scale/alloy interface sustains the high oxidation rates.1"3 The driving force for this transport is the difference in the oxygen activity of the outer wustite and that at the inner scale/alloy interface. In pure CO2, as well as in CO2-CO atmospheres, carburization of the alloy accompanies this oxidation. Current efforts to evaluate the parameters controlling this carburization have shown that the process is not simple; i.e., the carbon concentration in the alloy initially increases rapidly, reaches a maximum, and then decreases slowly as the oxidation time is extended. This is the same pattern reported by McCoy for the more complex oxidation-carburization of stainless steels and an Fe-Cr alloy in CO2 at lower temperatures.4 These changes in the carburization process occur while the overall oxidation rate and the lattice parameters of the scale layers remain constant. If this invariance of the lattice parameter is assumed to indicate a constant scale composition and thus a constant oxygen potential, the carburization results are not easily explained. Electron microprobe traces across the thickness of these outer scales, however, have revealed distinct chromium gradients penetrating 10 to 50 µ from the inner surface where the chromium concentrations were estimated at a few tenths percent. The variation of the chromium cmcentration on the inner surface of the scale, and the resulting change of the oxygen activity, during the oxidation process is considered to be important in defining the carburization process. Thus, to gain an understanding of the complex oxidation-carburization proc- ess, it was necessary to measure the properties of wustite containing known amounts of chromium (chromium wustite). Although the general features of the Fe-Cr-0 equilibrium diagram between 900° and 1300°C have been fairly well established by Richards and white: Wood-house and White,6 Seybolt,7 and Katsura and Muan,8 there have been no detailed studies of the limits of the chromium wustite phase field or the properties of these alloyed wustites. The recent results of a limited study of chromium wustite by Levin and wagner9 indicate that more than 0.67 wt pct Cr is soluble in wustite above 850°C and that this alloying is accompanied by a substantial lattice contraction. This change in the lattice parameter was not evident in the X-ray diffraction patterns of wustite layers from the oxidation experiments;1,3 the lines were sharp even though a chromium gradient existed in the scale. The present paper describes gravimetric equilibrium experiments which delineate the boundaries of the chromium wustite single-phase field at 1000°C and define the changes in the oxygen activity and the lattice parameter of wustite as functions of chromium and oxygen contents. The lattice parameter data of chromium wustite obtained from these equilibrium and special quenching experiments differ considerably from those reported.9 Those for pure wustite show significant differences from the widely accepted data of Jette and Foote.10 Since the causes of these differences are not easily assignable, and since the literature contains many sets of data on wustite which if not in conflict are at best not in harmony, the experimental procedures are discussed in the present paper. EXPERIMENTAL Oxide Preparation. The specimens used in these studies were porous pellets compacted from high-purity (Fe,Cr)2O3 or Fe2O3 powders. These powders were prepared from electrolytic chromium (99.8 pct purity) and electrolytic iron purified by consumable-electrode, vacuum arc-melting processing (299.9 pct purity).11 The oxides were produced by standard analytical procedures: solution of the metals in acids (HC1, then HNO3 added), coprecipitation of the hydroxides (NHaOH), and filtering and washing these precipitates. Initial dehydration of the coprecipitated hydroxides was done in a porcelain evaporating dish heated by a Meker-type burner, final dehydration by firing in a recrystallized alumina crucible at 1000" to 1050°C for 20 hr in an electrically heated furnace. Spectrographic analysis detected the following impurities: silicon, 0.01 pct or less; aluminum, 0.001 pct to trace; manganese and copper, 0.0001 pct to none. Each of these levels is at least one order of magnitude lower than in commercially available CP grade ferric and chromic oxides. Fluorescence analy-

Jan 1, 1969

By L. Eaton, A. W. Last, J. L. Stevens

COPPER ore from Kennecott Copper's Ray mine, about 60 miles southeast of Phoenix, Ariz., is concentrated at the company's mill at Hayden, some 18 miles south of the mine. The Hayden mill is currently treating 16,000 tons of ore per day by flotation, using raconite, a crude butyl xanthate, as a collector for the sulfide copper minerals and lime as a pyrite depressant.1 The ore contains significant amounts of nonsulfide copper minerals, but recovery of these values has been low. The Hayden mill is now being modified to provide for treatment of future ores by leach- precipitation-flotation (L-P-F). This modification, costing about $5 million, is expected to reduce the loss of nonsulfide copper values and improve overall copper recovery by an additional 2 lb per ton of ore.

Jan 11, 1957

By H. H. Hausner, H. S. Kalish

M. Hansen—This paper certainly is an interesting study. Although I have not had too much experience in the powder metallurgical methods of studying phase equilibria, I would like to say the following concerning the interpretations of the results obtained: 1. The existence of a zirconium-rich eutectic having a melting point close to 950°C and containing approximately 5 pct beryllium is well established. 2. Undoubtedly sintering of the original compacts (i.e., without repressing and resintering at 1350°C) resulted in a condition being far from equilibrium, even in the low-melting point zircon-rich region where undissolved zirconium particles have been observed. This means that only partial reaction between the component powders has taken place. 3. In preparing and handling powder mixtures for pressing and sintering, we have found that with powders differing considerably in density, and also in particle size, separation in layers of different composition may occur. This means that a concentration gradient would exist within such samples. This phenomenon may, at least to some extent, account for the difference in microstructure of the top and bottom regions of some of the sintered samples. If this is the case, density figures for some of the nominal compositions would not represent actual densities of those mixtures. 4. Fig. 1 shows that the low densities of mixtures with 40 and 60 pct beryllium sintered at 1350°C are changed to much higher densities if the products sintered at 1100°C are repressed and resintered at 1350°C, whereby an approach toward equilibrium takes place. This would mean that the low density and growth in volume is due to nonequilibrium conditions. If this is true, would it be justified, then, to conclude that "the remarkable growth of the alloys in the vicinity of 40 to 60 pct Be indicates the formation of a high-melting point phase, probably accompanied by a considerable change in volume due to a large alteration of the crystal structure from that of the original compounds"? If some compound formation has taken place already during the first sintering at 950" to 1350°C, more compound would be formed by repressing and re-sintering of the 1100" samples. This treatment, however, results in higher, rather than lower, densities. In general, the density-composition curve of alloy systems containing one or more intermediate phases is characterized by a more or less defined contraction (decrease in specific volume, increase in density) over the "theoretical" density. Does not discrepancy exist between the two statements that "growth of the alloy indicates the formation of a high-melting phase . . ." and "even at 1350°C, no indications of sintering have been observed"? 5. I am not sure that the explanation given for the fact that fig. 4 did not reveal as much eutectic as the top portions of the mixture with 2 pct Be, is correct. The density of the melt containing only 5 pct Be or even perhaps less, is not too much different from that of the nominal composition. The reason might be also that there was already some separation of the components in the pressed compact. 6. I do not understand why the microstructure of the bottom regions of the compact with 5 pct Be (fig. 6) is so different from that of the top regions (fig. 5). The compact was melted on sintering at 1100°C. Its composition lies close to the eutectic point. There should be at least some lamellar structure in the bottom regions too; otherwise, the composition of top and bottom must have been very different after sintering, because the eutectic is said to extend as far as the composition ZrBe2. In case the white and gray areas of fig. 6 are both gamma, and the black areas undissolved zirconium, this composition would be close to the phase coexisting with zirconium, that is, ZrBe2, according to the hypothetical diagram, or a compound richer in zirconium. 7. Figs. 9 and 10 are not mentioned in the text. 8. The great difference in microstructure of the composition 20 pct Be of figs. 8 and 14 on one side and fig. 15 on the other side proves that sintering at 950" and 1100°C results only in partial reaction of the powers. 9. The mixture with 60 pct Be (fig. 19) seems to consist of two phases, rather than one phase, one interspersed in a matrix of another. 10. The statement that the eta phase "may be an intermetallic compound or the product of a peritectic or monotectic reaction" seems to be misleading, because the product of a peritectic or monotectic reaction in this region of the system must be an intermetallic compound. 11. If there is some solid solubility of Be in alpha and beta-Zr, it would be expected to be higher in beta-Zr (b.c.c.) than in alpha-Zr (h.c.p.). The temperature of the polymorphic transformation of zirconium then would be lowered, rather than increased. In accordance with this, Battelle has found that the transformation point of titanium is decreased by beryllium. 12. In case the phases present in alloys with 80, 90, and 95 pct Be are identical (which appears to be correct), it is striking that the relative amounts of both phases (eta and beryllium) are not too different within this wide range of composition. With 60 to 65 pct Be

Jan 1, 1951

By Peter R. Drummond

THE final casting of refined copper has been re-J- stricted for generations by the following sequence of operations: Filling the reverberatory furnace, melting, skimming, blowing or flapping, and poling. The hoped-for 24 hr cycle, producing 300 tons or more, has been taken up largely with the necessary bat time-consuming tasks of cleaning the bath, sulphur elimination, and in turn removal of excess oxygen to produce tough-pitch copper. Incidental to comparatively slow melting under combustion gases, copper oxides react with the furnace lining, and the slag so-formed must be completely recycled. The three-phase arc furnace has eliminated some of the cycle stages, and telescoped the remainder into a continuous operation. Electrical energy, supplied to graphite electrodes enclosed in high grade refractories, rapidly melts copper cathodes and sustains a stream of metal, containing approximately 0.01 pct oxygen, without contamination from fuel. The arc was struck on the first large electric furnace for melting copper in the United States on April 13, 1949. The earliest use of this type of furnace was at Copper Cliff, Ont., in 1936, and an admirable description of their installation has been published? Copper, melted in the Baltimore furnace, is used to cast billets, and the installation differs somewhat from the Canadian, as will be described. The arc furnace is a heavy-duty, three-phase furnace, holding 50 tons, the general outline of which appears on Fig. 1. The steel shell is 15 ft ID with a bottom radius of 14 ft 2 in. The roof, separate and distinct from the body, consists of a 15-ft water-cooled, cast-steel ring of the same outside diameter as the furnace. The center line of the furnace lies 9 ft 6 in. from that of the trunnions, permitting a 5" backward tilt for skimming, and a 40" maximum nose tilt forward for complete draining. Normally, the furnace overflows by displacement, and the use of the forward tilt arrangement is restricted to covering charging delays. The charging slot, 3 ft 8 in. x 5 in., lies on the north center line, the tap hole on the south, and the 30x30 in. skim door 45" to the west of the slot. The original 20-in. graphite electrodes were replaced with 14 in. in December 1949. Three conventional direct current winch drives, governed by electrical controls, position each electrode which has individual mast supports and counterweights. An independent circulation supplies cooling water for the electrode glands, the roof ring, charge slot, and the skim door frame. Arc Furnace Refractories Hearth: Fused-in monolithic bottoms had been used in copper arc furnaces, installed prior to April 1949. These consisted of thin layers of periclase, successively fused in place over preliminary brick courses. Heat was obtained from the arc, using a T-like arrangement of broken electrodes resting directly on the periclase to be fused. The operation, taking weeks to perform, was very expensive. The chemically-bonded magnesite-brick bottom, installed at Baltimore, was the first of its kind and a radical departure from previous practice. It consists of a 1 to 6-in. layer of castable refractory laid on the steel shell, modifying it to a 12 ft 2 in. bottom radius. Two courses of 9x2 % -in. fireclay straights and keys follow. The third course is made of 9-in. magnesite blocks of special shape to form circles of an inverted arch. It was started by a four piece keystone with skew-backs forming the outer course. The fourth course also started on a central keystone, or button, of four 90" segments, 12 in. diam x 13 Vz in. deep, and continued with 13%-in. blocks. Skewbacks at the shell completed the course to produce a horizontal surface for the side walls with a single course of No. 2 arch fireclay against the steel. Dry chrome-magnesite cement was brushed over each course after laying, and a 1-in. expansion space between the brick and the shell was filled with the same mixture. The total bottom thickness, excluding the castable material, was 5 in. of clay plus 22% in. of chemically-bonded magnesite. Tap Hole: A 5-in. OD and 3-in. ID silicon-carbide tube constitutes the tap hole and is set tangential to the upper course of the furnace bottom. Molten metal fills the tube when the furnace is level and filled to capacity. Side Walls: The lining, against the shell, consists of a 9x4Y2x3 in. soldier course of fireclay, using straights and No. 1 arches to turn the circles. A second soldier course of 9x4'/2x2'/2-in. fireclay was laid in a somewhat similar fashion. Three courses of 13Y2x6x3 in. and 9x6~3 in. of final magnesite, laid flat, completed the lining, using Nos. 1 and 2 keys to turn the circles. Cardboard spacers were placed between every two bricks in horizontal courses, and a thin coat of chrome-magnesite cement filled the joints between the firebrick and magnesite. A sprung-arch spanned the skim door with jambs of suitable magnesite shapes. Charge Slot: The slot is 3 ft 8 in. wide x 5 in. high. A silicon-carbide sill of special shapes has a 30" slope to allow cathodes to slide easily into the bath. The original arch was flat, and composed of Nos. 1 and 2 wedge magnesite with a 6-ft radius. It projected 5 in. over the sill, and, being a flat arch, gave an 18 15/16-in. opening between the inner edge and the metal line. The whole assembly was later raised 9 in., and the flat arch replaced with an arch, the lower edge of which maintained the 5-in, width from the outer to inner edges as shown in Fig. 2. A water-cooled, cast-copper jacket protects the steel shell behind the slot.

Jan 1, 1952

By Klaus Schwerdtfeger, Hans-Jürgen Engell

Activities of silicon in Ni-Si melts have beelz determined in the temperature range 1480° to 1610°C from electromotive-force measurements involving the cells The data obtained are used to derive the activities of nickel and the integal free energies of mixing. Entropies of mixing are calculated from the free energies of mixing as obtained in the present study and the heats of mixing as available in the literature. ACTIVITIES in Fe-Si and Co-Si melts have been determined recently by the authors&apos; using galvanic cells consisting of alloy, an oxygen electrode, and an oxide melt as electrolyte. The present paper deals with activities in Ni-Si melts as measured with the same technique. A schematic diagram of the cell is shown in Fig. 1. The alloy and the electrolyte consisting of CaO and SiO2 are contained together in a silica-glass crucible. During the experiment the silica glass crystallizes to cristobalite on the surface of the crucible. Nickel contents of the electrolyte are very small (<0.1 pct as checked with chemical analysis), because of the noble character of nickel in comparison with silicon. A tapered silica tube is connected to the crucible through which a platinum or molybdenum wire is inserted, as shown in Fig. 1. A platinum tube reaches the surface of the CaO-SiO2 electrolyte from above. The platinum tube is provided with four holes on its side, through which oxygen of 1 atm pressure is blown over the electrolyte. The cell reaction is given by the equation Si(metal) + O2(gas) = SiO2(electrolyte) [3] and the galvanic electromotive force of the cell is given by the formula

Jan 1, 1965

By Milton H. Fies

THE writer wishes to acknowledge at the outset his great sense of obligation to those who contributed so broadly and expertly to the preparation of this paper: Dr. Albert DeSmaele, Chairman of the Board of Directors of Socogaz, Belgium; Dr. Julien Venter, Director of the National Institute of Coal Mining and Coal Utilization Industry, Belgium; Dr. Roger Loison, Chief Engineer, French National Coal Research Board, France; and Dr. Erich Sarapuu of the Sinclair Coal Co., Kansas City, Missouri. Liberal use has been made in this paper of a recent publication on Russian, Italian, Belgian, and French experiments prepared jointly by the Centre d&apos;Etudes et Recherches des Charbonnages de France (Cerchar) and the Institut National de l&apos;Industrie Charbonnière of Belgium (Inichar).1 The writer is particularly indebted to Dr. E. T. Wilkins, of the Fuel Re¬search Station, London, and to Mr. James L. Elder, of the Alabama Under¬ground Gasification Experiment at Gorgas, Alabama, for their unfailing patience and effective support. Not only did these experienced and capable men edit and revise this discussion, but much of its content is a direct con¬tribution quoted in full from their memoranda. Without the assistance of all these colleagues, this presentation would not have been possible. It has been a privilege to serve and work with them and to acknowledge repeatedly their loyal cooperation. The recovery of the energy inherent in coal beds throughout the world has been done through the years by methods that today may be justly regarded as primitive. While the techniques of coal mining through the application of machines and the enhancement of information and skills have advanced to an extraordinary extent, particularly during the past 20 years, the underlying means is essentially the same as when man first began to mine coal. Despite this progress in the manner of coal mining, it continues today as a hazardous, toilsome, grimy task. Coal mining per se has advanced at a greater and more rapid stride in the past 25 years than the mining of any: other mineral, but the basic method is fundamentally the same as it was the first day a miner took a pick into his hands many centuries ago. This situation presents a challenge to mining engineers everywhere, from

Jan 1, 1953

By Walter Bradley

MINING by hydraulic process of the important gold-bearing gravels of the Sacramento Valley in the basins of the Yuba, Bear and American rivers began in 1853, and continued at an ever-increasing rate for 30 years. In its most active days it reached an annual production of $15,000,000, and averaged $10,000,000 per year over the 30 years. During that period no provisions were made to prevent the debris from being dis-charged into the water courses, and ultimately large quantities of silt, sand and gravel were washed down to the lower valleys; filling channels, causing overflow of agricultural lands and difficulty in maintaining navigable depths in the Sacramento River. Agitation and suits filed because of these damages finally resulted in the injunction decision of Judge L. B. Sawyer,1 in the U.S. Circuit Court, Jan. 23, 1884, which closed down practically all hydraulic mining operations not having means to restrain their debris. In 1893 (approved March 1, 1893), Congress passed the act introduced by Representative Anthony Caminetti, of California, creating the California Debris Com-mission, composed of three officers assigned from the Engineer Corps of the U.S. Army, and since that time it has been legal and possible within the drainage systems of Sacramento and San Joaquin rivers to conduct hydraulic mining of gold-bearing gravels behind dams built under this commission&apos;s permit and supervision. In the watersheds of the Trinity and Klamath rivers, which flow directly to the Pacific Ocean and do not affect navigation or agriculture, operating permits from the California Debris Commission are not required. There is a measure of restriction there, however,. through what is known as the Trinity and Klamath River Fish and Game Dis-trict. Chap. 215, Stat. 1931, in order to secure relatively clear water for the fishing season, provides that between July 15 and October 15 each year there must not be discharged into these rivers debris that will cause a turbidity greater than a content of 50 parts per million in the

Jan 1, 1936

By Max Hebgen

Within the State of Montana the streams rise in the high mountains at. an elevation of from 5,000 to 8,000 ft. These streams leave the State line both east and west at elevations from 3,500 to 2,400 ft. It is, therefore, apparent. that all these streams have an average fall of 3,000 ft. within the confines of the. State, and many opportunities are presented on all streams. for the development of power, by taking advantage of the natural fall. It is probable that 1,000,000 h. p. can :be developed in the State of Montana. I. NATURAL FEATURES OF STATE AFFECTING POWER DEVELOPMENT. The main. range of the Rocky mountains, forming the Continental Divide, cuts the State of Montana into two parts. The eastern part is drained by the Missouri river and its tributaries, the Madison; Jefferson, Gallatin and Yellowstone, rivers. The western part is drained by tributaries to the Columbia river, the Clarks fork and the Kootenai river. The Clarks fork in turn is formed by the junction of Missoula and Flathead rivers, the latter, draining Flathead lake. The western part of the State. is mountainous and the eastern part is comparatively level. As a natural result the rivers in the western part are capable of generating large amounts of power, while in the eastern part of the State natural power sites are much fewer and farther apart. It also follows that in the mountainous districts large amounts of power are required for the mining industry, while in the eastern part of the State, which is principally devoted to agriculture, power is required in smaller quantities. ?

Jan 8, 1913

By G. H. Kesler, J. E. Oberele, C. E. Dryden, J. H. Oxley

Heat-transfer rates were measured in a model of a multifilament vapor-deposition bulb fo the preparation of high-purzty metals. Local transfer coefficients for heat transfer frow the filaments to the circuates process stream were determined as a functiol of gas flow rates and bulb, inlet, and filament, geowzetvies. These results a-e then convertted to n mass-t7,ansfer basis to provide a method of correlating vapor-deposition rates and to predict the performance of commercial urzits. The firm1 cor?,elating equation for mass transfer was found to be- wheve k, is the mass-transfer coefficient; D, is bze gas difficsivity : P is the system pressure; R is the gas constant; T is the gas temperature; Df, DB, and Di ave tlze diameters of the filament, bulb, and inlet, respectively; k is the gas conductivity; C, is the specific heat of the gas, M is the wzolecular zleight of the gas; Npr . N,,, NRe a7&apos;e the Prandtl, Schmidt, and Reynolds numbem of the system, respectively; LB is the height of the bulb; and SB and Sf are the total suyiace area of the bulb and filaments, respectively. ONE of the more conventional methods of preparing very high-purity metals is the vapor deposition of the metal upon heated filaments. The reactions which can be employed in such a process generally fall into two classes: 1) Pyrolysis of a volatile metal compound. Generally because of their instabilities, metal iodides are used; however, other metal halides and hydrides have been employed. These processes are frequently carried out under vacuum conditions, and the filaments are maintained at high temperatures. 2) Hydrogen reduction of a volatile metal compound. A metal chloride is normally the preferred feed for these processes, but other halides are sometimes used under special conditions. These hydro- gen-reduction processes are usually operated at atmospheric pressure. Many of the current processes for the production of semiconductor materials are actually vapor-deposition processes. However, the vapor-deposition process itself is relatively old, and almost all metals can be prepared in a state of very high purity by the use of vapor-deposition techniques. Loonam has recently given an excellent review of the iodide process for metal deposition,&apos; and Owen has started some detailed studies with a carbonyl system.&apos; A more general treatment of all vapor-deposition processes has been outlined by Powell, Campbell, and Gonser.3 Despite the fact that vapor-deposition techniques have been employed since 1890, there is a surprising lack of fundamental information regarding the transport characteristics of even the simplest deposition system, the heated filament. The purpose of the investigation described in this paper was to extend some of the earlier data obtained at Battelle to predict deposition rates and the uniformity of deposition in large-diameter, multifilament deposition bulbs under forced convection conditions.4&apos;5 A number of other investigators have already presented a simplified treatment of the deposition process under non-flow conditions, i.e., pure diffusion.6"9 To obtain information on the transport characteristics of a deposition bulb, a model of a typical plant deposition unit was constructed, and local heat-transfer coefficients from the filaments to a circulating air stream were determined under various conditions of air-flow rates and bulb, inlet, and filament geometries. These results were then converted to a mass-transfer basis, and consequently provided a method to correlate experimental vapor-deposition rates and to design commercial deposition units. EXPERIMENTAL WORK Description of Model. The apparatus which was used in this work was a scaled model of one type of deposition bulb. It was constructed of Lucite and was easily altered to give several combinations of diameter of bulb liner, inlet size and location, number of filaments, and outlet geometry. The model is shown in Figs. 1 and 2. The bulb shell was made octagonal for convenience in construction and observation, and the bulb liners were cylindrical. Air, introduced through one of several different jet inlets, was used as the test fluid in these model studies. Filaments for deposition of metal were simulated by metal rods 1/4-in. in diam. Two of the rods could be heated by passing electrical current through them ¦ while the remaining rods could not be heated. This procedure minimized the amount of heat which was

Jan 1, 1962

By C. G. Dunn

Many investigations have been made concerning the nature of plastic deformation and recrystallization of metals either in the form of polycrystalline materials or in the form of single crystals. However, similar work on strip materials composed of large grains as thick as the strip and having a high degree of preferred crystal oricntation has not been carried out extensively. Such materials are ideal not only for studying changes in single crystals under conditions where neighboring grains exert their influences but also for obtaining the complete change in orientation of a grain or group of grains during the course of plastic deformation and subsequent recrystallization. It is well known that first-order twins in the form of Neumann bands may be produced during the plastic deformation of ferrite crystals, particularly silicon ferrite crystals.l--3 Furthermore, it is believed that high-stress regions exist in the vicinity of these bands4. and it has been said that these banded regions would be active in recrystallization processes.5 Evidence to that effect in silicon ferrite had already been presented with photomicrographs showing recrystallization among Neumann bands during the early stages of recrystallizati~n.5,6 Similar evidence has been published for nonferrous metals5 Merging of fine parallel deformation bands during annealing to form twin bands of ordinary appearance in alpha brass has been offered not only as evidence of an active role being played by mechanical twins but also as evidence that such twins cxisted prior to recrystalli~ation.5 Proof that such new structures are actually first-order twins, or even twins at all, must be considered inadequate except for those cases where X-ray or optical data have been obtained to confirm the necessary oricntation relationship.7,8 A. B. Greninger has obtained excellent iliustrations of annealing twins in alpha iron.9 Since his material was previously deformed by sharp hammering, a process that generally induces Neumann bands, the existence of twins following annealing might suggest that they grew from mechanical twins. In connection with transformation twins in alpha iron, Greninger reported that grains containing three twin orientations occurred rarely and none occurred with three sets of well-developed bands.9 The work at the Pittsfield Works Laboratory on silicon ferrite in the form of large-grained strip steel deformed a small amount and annealed to partially recrystallize the grains indicates that the deformation and recrystallization processes that lead to annealing twins involvc more complex processes than the formation of Neumann bands and the growth of such bands. Some groups of annealing twins are obtained which contain not only three well-developed twin structures, but also contain more than one order of twins. It is also shown, in one case, that an interrelated group of twins did not arise within one single parent grain and, furthermore, orientations of grains in the group

Jan 1, 1944

By C. G. Dunn

Many investigations have been made concerning the nature of plastic deformation and recrystallization of metals either in the form of polycrystalline materials or in the form of single crystals. However, similar work on strip materials composed of large grains as thick as the strip and having a high degree of preferred crystal oricntation has not been carried out extensively. Such materials are ideal not only for studying changes in single crystals under conditions where neighboring grains exert their influences but also for obtaining the complete change in orientation of a grain or group of grains during the course of plastic deformation and subsequent recrystallization. It is well known that first-order twins in the form of Neumann bands may be produced during the plastic deformation of ferrite crystals, particularly silicon ferrite crystals.l--3 Furthermore, it is believed that high-stress regions exist in the vicinity of these bands4. and it has been said that these banded regions would be active in recrystallization processes.5 Evidence to that effect in silicon ferrite had already been presented with photomicrographs showing recrystallization among Neumann bands during the early stages of recrystallizati~n.5,6 Similar evidence has been published for nonferrous metals5 Merging of fine parallel deformation bands during annealing to form twin bands of ordinary appearance in alpha brass has been offered not only as evidence of an active role being played by mechanical twins but also as evidence that such twins cxisted prior to recrystalli~ation.5 Proof that such new structures are actually first-order twins, or even twins at all, must be considered inadequate except for those cases where X-ray or optical data have been obtained to confirm the necessary oricntation relationship.7,8 A. B. Greninger has obtained excellent iliustrations of annealing twins in alpha iron.9 Since his material was previously deformed by sharp hammering, a process that generally induces Neumann bands, the existence of twins following annealing might suggest that they grew from mechanical twins. In connection with transformation twins in alpha iron, Greninger reported that grains containing three twin orientations occurred rarely and none occurred with three sets of well-developed bands.9 The work at the Pittsfield Works Laboratory on silicon ferrite in the form of large-grained strip steel deformed a small amount and annealed to partially recrystallize the grains indicates that the deformation and recrystallization processes that lead to annealing twins involvc more complex processes than the formation of Neumann bands and the growth of such bands. Some groups of annealing twins are obtained which contain not only three well-developed twin structures, but also contain more than one order of twins. It is also shown, in one case, that an interrelated group of twins did not arise within one single parent grain and, furthermore, orientations of grains in the group

Jan 1, 1944