Search Documents

By W. WANJUKOW, H. O. Hofman

(New York Meeting, February, 1313.) I. INTRODUCTION. IN the metallurgical treatment of most metallic sulphides it is usually necessary to carry on a roasting-operation. In some cases the raw ore will have to be roasted.; in others the intermediary product, matte, produced in smelting the ore; again, both ore and matte may have to be subjected to oxidation at elevated temperatures. Most metallic sulphides, when given an oxidizing-roast, pass through the state of sulphate before they are converted into oxides. All metallic sulphates are completely decomposed by heat, with the exception of those of lead and bismuth, but the temperatures at which decompositions take place vary with the metals. Some metallic sulphates are converted directly into oxides, others first form basic salts. Alkali-earth sulphates show a behavior similar to that of metallic sulphates, while alkali sulphates do not part with their sulphur trioxide even at elevated roasting-temperatures. The older data on the decomposition of metallic sulphates by beat are only approximations. Thus Kerl 1 gives the order in which metallic sulphates are decomposed with increasing temperatures as (Ag2, Fe, Cu, Zn, Ni, CO, Mn, Pb) SO4. More recent statements give definite temperatures and modify the formerly accepted order of decomposition. But the temperatures given by various observers do not agree. The reasons for this are to be found mainly in the method and manner of carrying out experiments. Four methods have been used: 1. Heating in an evacuated tube; 2, heating in a tube closed at one end, without air-cur-

Sep 1, 1912

By A. W. Schlechten, R. P. Abendroth

Jan 1, 1960

By S. M. M. Safvi, A. Jowett

Small-scale continuous flotation tests are described in which the influence of 1) pulp density and 2) feed rate on the rate of flotation are investigated. The results provide further evidence of first-order kinetics for flotation and indicate that tests at different feed rates provide a particularly simple method of determining rate constants. Flotation kinetics are discussed in general terms. Over a period of many years numerous research workers have studied the rate of recovery of valuable materials from flotation pulps with a view to deter-mining the mechanism of the froth flotation process. Froth flo ation is fundamentally a collision process involviug at some stage collision and then mutual attachment between air bubbles and mineral particles. It is possible to draw analogies therefore between the flotation process involving mainly macroscopic particles and the ordinary processes of chemical reaction kinetics involving collisions between atoms, molecules and ions. By adopting this analogy we may postulate a general equation representing the kinetics of the flotation process: -dC/dt =K.CC ,Aa (1) The rate constant, K, will be a complex function involving reagent concentrations, particle and bubble sizes, induction times and no doubt flotation cell design. However, these are factors which can be kept constant in any series of experiments, permitting investigation of the exponents a and c, which determine the order of the reaction occurring in flotation. The various research investigations carried out so far have all aimed at evaluating a and c and in the majority of cases only since the concentration of air has usually been kept constant in a series of tests, so that a relationship of the following type has been investigated: -dC/dt = K1 Cc (2) The techniques of both batch testing and continuous testing have been used to investigate this relationship. The technique of continuous testing, in which steady-state conditions are established, permits direct investigation of the above equation. In the case of batch testing, C is decreasing continuously

Jan 1, 1961

By Jack L. Taylor

As expected from similar crystal structures and favorable atomic size factors, titanium, vanadium, and molybdenum are completely soluble in one another above the transformation temperature of titanium. The fl phase parameters of the continuous solid solution are shown graphically. Limiting compositions for retained fl phase have been determined. VANADIUM and molybdenum both have body-centered-cubic structures at all temperatures and, from the atomic diameter comparison factor, 3.9 pct, would be expected to form a complete series of solid solutions. The existence of complete solubility has been confirmed by work' at the Jet Propulsion Laboratory. Furthermore, vanadium and molybdenum have favorable atomic size factors to form complete binary solid solutions with the B phase, high temperature form of titanium, which also has body-centered-cubic structure. Pietro-kowsky and Duwez' and Hansen et al." have established the existence of the complete series of solutions in these binary systems. It would be logical, therefore, to expect that p-titanium, vanadium, and molybdenum would be completely soluble in one

Jan 1, 1957

By Nicholas J. Grant, Olaf Troili, John Chipman

IN recent studies of the factors which affect the rate of desulphurization and its equilibrium, it became apparent that certain concurrent reactions were operative which had a significant effect on desulphurization. This is emphasized in the experiments of Hatch and Chipman1 and of Grant, Kalling, and Chipman' by the slow approach to a final state of equilibrium which is in marked contrast to the initial rapid transfer of sulphur from metal to slag. Since the removal of sulphur is of such profound importance in iron and steelmaking, it appeared necessary to investigate the reactions responsible for this behavior. It is now known that the presence of iron oxide in the slag interferes seriously with the principal reaction of blast-furnace desulphurization: CaO (slag) +-S + C - CaS (slag) + CO [l] The interfering reaction is most simply expressed as: CaS (slag) + 0 = CaO (slag) +-S 121 and a small concentration of oxygen (or FeO) is sufficient to hold a considerable amount of sulphur in the metal. It has been shown by Grant, Kalling, and Chipman2 that the addition of MnO to blast-furnace slag slows the removal of sulphur from the metal. This effect overshadows the contribution of MnO to basicity and is ascribed to its oxidizing power. It will be shown in this paper that SiO, also has sufficient oxidizing power to interfere with blastfurnace desulphurization. This is, of course, only one of its several effects. Primarily it is an acid and therefore reduces the concentration of excess lime. But when silicon is reduced to the metal the oxygen to which it was previously bonded becomes in part available for reaction 2. The proof of this statement is found in the following experiments. Experimental Procedure and Results Utilizing the same procedure and apparatus described by Grant, Kalling, and Chipman' five additional heats were made using slags IV and 11, the starting compositions of which were: slag IV—40 CaO, 10 MgO, 35 SiO,, 15 A1,0,; and slag 11—50 CaO, 10 MgO, 25 SiO,, 15 Al3O3. An important difference between these heats and those previously reported was that silicon to the extent of 1 to 4 pct was added to the present heats whereas the starting silicon content was formerly about 0.2 pct. Table I shows the slag and metal analyses for heats 82 to 87, and Table I1 shows the silicon addi- tions made to the charge. These additions are based on 400 g of metal and 400 g of slag. All heats had 1.65 400pct S charged before the cold slagadditions. The temperature was maintained at 1525°C. Rate of SiO, Reduction: Fig. 1 shows the silicon content of the metal in contact with slag IV at 1525°C as a function of time. Heat 70 from the work of Grant, afunctionKalling,of and Chipman is included as the lowest starting silicon. It will be noted that eeven with 4 pct Si in the starting metal, there is an increase in silicon content with time. Heat 84 is apparently approaching silicon equilibrium very slowly. Heats 70 and 82 with very much lower slowly.starting silicon show a more rapid initial rise in startingsilicon content but do not reach equilibrium during a long holding period. Fig. 2 shows 3 different initial silicon contents for Fig.2shows3differentheats 73 (from Grant, Kalling, and Chipman) 86 and 87, in contact with slag II, the most basic slag. Heat 73 is increasing in silicon with time, whereas heat 87 with an initial silicon content of 3.7 pct shows a decrease with time. Heat 86 shows a very close approach to equilibrium. The rate of transfer of silicon from slag to equilibrium.metal is very slow in all of those heats, even those which are initially far from equilibrium. ____

Jan 1, 1952

By D. A. Crerar, R. L. P. Kleinmann, R. R. Pacelli

A bacterium, Thiobacillus ferrooxidans, is of prime importance in the formation of acid drainage from pyritic material. Above pH 4.5, T. ferrooxidans increases initial acidification; below pH 4.5, it allows acidification to continue by oxidizing Fe2 +. Below a pH of approximately 2.5, the activity of F3+ is significant and results in steady-state cycling between oxidation of pyrite by Fe3 + and bacterial oxidation of Fe2 +. Laboratory and field tests demonstrate that inhibition of T. ferrooxidans by controlled release of anionic detergents can inexpensively reduce pyrite oxidation and acid formation.

Jan 1, 1982

By A. V. Deforest, A. R. Anderson, C. W. MacGregor

ONE of the important problems in the design of structures and machine parts subjected to rapidly applied loads is the determination of the strength and ductility of the material itself under such conditions. Realizing the need for such information, many investigations have been carried out in the past. Most of these experiments have been made using notched bars in bending either with the Charpy or Izod impact machine. While yielding valuable data on the effect of notches in the energy absorption of the material and on the condition of heat-treatment, this form of test does not lend itself readily to a determination of fundamental stress-strain relations. For this and other reasons, more attention has been paid recently to the tension impact test. An extensive literature already exists on the subject and only those investigations somewhat closely related to the present paper will be mentioned. For a more comprehensive list, the reader is referred to the Symposium on Impact Testing of the A.S.T.M., 1938. The work of Mann,1 Clark and Dätwyler,2 Nádai and Manjoine,3 Winlock and Leiter,4 Deutler,5 and Brinkmann,6 however, deserve especial mention. In most of the previous investigations on the subject, when stress-strain relations were obtained under high rates of loading, it was the common procedure to determine stresses based on the original area and strains based on the original length. Stress-strain curves were then constructed by plotting [So = ooT as a function of eo =o] where A o and Lo refer to the original area and gauge length, respectively. At present there exists a paucity of true stress-strain data in the impact problem. The advantages of constructing so-called true stress-strain curves in order to reveal the fundamental physical properties of the material for the tension test were discussed recently by one of the authors? It was shown that the true physical behavior of the material in the tension test could best be represented by plotting the average true stress, [S = P] as a function of [e = q' = log A-le = log Lo] where P, A, L, S, [e], and q' refer to the load, the cross-sectioned area while the load P is applied, the actual gauge length, the average true stress, the true strain and true reduction in area, respectively. Besides giving a better physical representation, the method has certain additional advantages in that the stress-strain curve so plotted becomes a straight line from the maximum load point to fracture. The construction of such curves, however, while comparatively simple for the slow rates of loading customarily used in the tension test, presents certain difficulties for tensile impact in that both loads and diameters are required throughout the test. The continuous measurement of test-piece

Jan 1, 1941

By H. J. Engell, W. Frank, A. Seeger

SWISHER and ~urkdogan' have determined the solubility of oxygen in a iron. They found it to lie between 7 and 10.5 at.-ppm at 881°C. Using earlier work on the permeability of oxygen in bcc iron,' they arrived at the following expression for the diffusion coefficient of oxygen in bcc iron (k = Boltzmann's constant, T = absolute temperature): where The present authors3 have estimated the activation energy QD for the diffusion of oxygen in bcc iron in two different ways from various experimental data.2'4"6 In the first method QD + QS (QS = heat of solution for oxygen in bcc iron in thermodynamic equilibrium with solid FeO) was determined either from data on the reduction of FeO with hydrogen4 or from measurements of the internal oxidation of silicon in a iron.5 Using an estimate of QS from investigations of the oxygen solubility in 6 iron2 (in thermodynamic equilibrium with molten FeO) Q = 0.97 ev or Q~ = 1.06 ev were obtained. From the magnitude of these values it was concluded that oxygen migrates interstitially in bcc iron and that consequently the activation energy QD for diffusion of oxygen has to be identified with the migration energy E~ of the oxygen atoms. Therefore, for a second estimate of QD from the diffusion coefficient of oxygen in 6 iron at 1450" ~,~ we used the theoretical expression:3 (a = length of elementary cube edge, m = mass of interstitially diffusing atom, sM = migration entropy), applicable to diffusion via the octahedral interstices in bcc lattices. Taking sM = 3.8 k (migration entropy of carbon in a iron), one gets Q = 0.90 ev. Hence, in Ref. 3 Q = (0.98 *0.1) ev was proposed as a plausible value for the diffusion energy of oxygen in bcc iron. sM + 9 (9 = solution entropy for oxygen in bcc iron) can be determined from permeability measurements.4 Using the above-mentioned estimate for QS , the following expression for the solubility c (atomic concentration) of oxygen (in thermodynamic equilibrium with solid FeO) in bcc iron was derived: From [4] the solubility of oxygen at 881°C in a iron is calculated to lie between 0.6 and 12 at.-ppm. We see that the solubility determined by Swisher and

Jan 1, 1969

By George Simkovich

It was hypothesized that solid-state point defects should alter the flotation properties of solids. Tests conducted on pure AgCl and AgCl doped with CdC12 show that atomic point defects exhibit an important role in the floatability of AgC1. Tests conducted on PbS doped with Ag2s or Bi2S3, also show that the defect structures resulting from these dope additions, i.e., a combination of electronic and atomic point defects, contribute significantly to the flotation of PbS. IT has been established that flotation occurs only when a finite contact angle exists between a solid and a gaseous bubble.' This angle, measured through the liquid phase, is expressed by the equation where the are inter facial free energies and the subscripts S, G, and L represent solid, gas, and liquid phases, respectively. As is seen in Eq. [I] three interface free energies, sG, sl, and GL, enter into the contact angle equation. Therefore, any variation in these energies which sufficiently varies the contact angle will, in turn, vary flotation processes. Changes made in any of the phases concerned, i.e., gas, liquid, or solid phase, are reflected through the changes occurring in two of the surface energy terms. Thus, a change in the liquid composition would be noted in sL and GL, and it is this phase, the liquid, which is most frequently altered in flotation studies., Changes in the solid phase must be reflected through the changes occurring in the sG and sL terms. In particular, it is hypothesized that changes in the surface concentrations of point defects in the solid-phase will alter the sG and sL terms which, in turn, will be reflected by flotation results. As an illustration of this hypothesis one may consider the defect structure and the flotation of AgC1. The bulk defect structure of AgCl is essentially one involving equal number of cation vacancies and interstitial cations.3 Upon adding CdC1, to AgC1, a greater number of silver ion vacancies are created in the bulk of the crystal.4 On the surface of the crystal the smaller binding forces and the free space accomodations may also allow for the creation of "surface interstitial anions", which will be designated as ad-anions. Thus, the point defect structure of the surface of AgCl doped with CdCl, will consist of cation vacancies and/or adanions. If the molecular forces responsible for the surface energies, ?SG and ?sL, are significantly altered by the presence of these surface point defects, then differences in flotation results will be noted as the concentration of these defects is varied. The defects present in AgCl are predominantly atomic in nature. In the case of PbS both electronic and atomic defects are present.5 This compound conducts electrically by either electrons or electron holes depending upon whether excess lead or excess sulfur is present. Upon disolving BiS3 in stoichio-metric PbS, one increases the concentration of cation vacancies and the number of electron carriers in the bulk of the crystal.5" At the surface, the possibility of ad-anions must also be considered. Conversely, upon dissolving AgS in stoichiometric PbS one increases the concentration of interstitial cations and the number of electronhole carriers in the bulk of the crystal.5,6' At the surface the interstitial cations will be designated as ad-cations. Thus, the point defect structure of the surface of a PbS crystal doped with Bi2S3 will consist of a number of cation vacancies and/or ad-anions and an excess of electrons. Conversely the point defects on the surface of a PbS crystal doped with Ag2S will consist of a number of ad-cations and an excess of electron holes. Again, as in the case of AgC1, should the molecular forces responsible for the magnitude of the interface free energies, ?sG and ?sL, be significantly altered by the presence of these surface defects then significant differences in flotation results will be noted as the concentration of these defects is varied. EXPERIMENTAL To test this hypothesis flotation tests were conducted on pure and doped AgCl and on PbS doped with either Bi2S3 or Ag2S. Preparation of the AgCl samples was performed as follows: AgCl and weighed amounts of CdC1, were melted in a porcelain crucible. The melt was then forced through a capillary tube and the particles emitted solidified in air as they fell about 1.5 meters. Spherical particles, -0.50 + 0.25 mm, were separated from the remaining solidified material

Jan 1, 1963

By R. G. Charles, E. A. Gulbransen, S. Barnartt

KINETICS of the reaction of zirconium with pure oxygen at elevated temperatures have been studied by several workers for periods of time up to 6 hr.1-1 In two cases,3-4 . the experimental values of oxygen uptake, w, as a function of time, t, were best fitted to the parabolic rate law w2 = kPt + constant. In others,3,4 the cubic rate law w3 = kot + constant, showed better agreement. The most recent data of Gulbransen and Andrew4 indicate that the choice between the parabolic and cubic laws for empirical representation of the data will often be arbitrary. This is particularly true if the first few minutes of the reaction with a clean zirconium surface is attributed to a different oxidation mechanism, for deviations from either rate law were found primarily during the initial period. Thus, the kinetics of this reaction have been too uncertain to permit safe extrapolation to oxidation periods of practical interest (many hundreds of hours). The data to be described are of interest, for they indicate that the cubic rate law applies over long oxidation times. The reaction of zirconium with oxygen at 1 atm pressure was followed at 350" and 450°C for 500 and 200 hr, respectively. Abraded test specimens of pure zirconium sheet' 3.0 X 2.0 X 0.012 cm in size were oxidized by the procedure previously described,3 which included periodic cooling to room temperature for weighing. The surfaces were polished to a 4/0 finish using polishing paper wet with kerosene, then wiped with petroleum ether and washed in redistilled acetone. Fig. 1 shows plots of log ? vs log t. Each curve represents the average of duplicate measurements, and deviations from the average were generally less than 3 pet. The cubic rate law (slope = 1/3) is closely followed. The rate constants, 5.2, x 10 -6 and 2.4, X 10- (mg cm-2)3 per hr at 350" and 450 oC, respectively, are plotted as log k, vs 1/T in Fig. 2, together with cubic constants calculated from the data of Gulbransen and Andrew4 for abraded specimens from the same lot of zirconium. Their data refer to runs of 6-hr duration at a pressure of 0.1 atm 0 and under conditions of uninterrupted heating. In spite of these differences, the latter data yield a straight line which appears to apply equally well to the new extended time data. The energy of activation for the oxidation process, calculated from the slope of this line, i.s 38 keal per mole. This may be compared with the value of 47 keal per mole found by Belle and Mallett3 at higher temperatures. It may be concluded tentatively that extrapolation of short-term oxidation data for zirconium to obtain the long-term behavior is best done through the cubic equation ?3 = kpt + constant. References ' E. A. Gulbransen and K. F. Andrew: AIME Trans., 1949, vol. 185, p. A.515; JouRNal OF Metals, August 1949. 'D.p. Cubicciotti Journal Amer Chemical August1949.Soc., 1950, Vol. 72, P. 3 V. Belle and M. W. Mallett: Joulnal Electro chemical Soc., 1954, ' E. A. Gulbransen 339.and K. F. Andrew: Oxidation of Zirconium Between 400" Gulbransenand 800'C.and AIME Trarzs.. 1957, vol. 209, p. 394; JOUR-Nal of Metals, April 1957. IS Barnartt, B G. Charles, and E. A. Gulbransen: Oxidation of 50 weight pet uranium-zirconium alloy, Journul Electrochemical SOC., 1957, vol. 104, p. 218.

Jan 1, 1959

By E. W. Cawthorne, R. I. Jaffee, C. M. Craighead

SOLUTION of a solid metal or alloy in a molten metal bath is used daily in melting operations, extractive metallurgical processes, and in brazing. It is generally recognized that temperature, time, agitation, and the composition of the solute metal and the solvent bath all affect solution rate. However, there is little information available in the literature on the kinetics of the process or the relative effect that these variables have on solution rate. In connection with an aluminum brazing study, data on the solution of aluminum in an A1-Si* bath to promote rapid solidification. The chemical analyses were made on drillings taken from the cast plates. The results of this work are listed in Table I. The thermal-analysis data were obtained on 200 gram samples cooled at approximately 1.5" per min. A calibrated chromel-alumel couple was used. The thermal arrests were recorded autographically on a General Electric photoelectric potentiometer recorder. The instrument was calibrated to 22.5 pct. The thermal emf was bucked with a Leeds and Northrup semiprecision potentiometer so that 1 mv represented the full scale of the GE recorder. Referring to Table I, it will be noted that the analytical results tend to be lower than the intended compositions by about 0.3 pct Si in the higher ranges. In view of the known difficulties in obtaining accurate silicon determinations by wet analysis when the silicon content is high and in view of the care that was employed in weighing and preparing the alloys, the intended compositions are believed to be more accurate than the analyses. Furthermore, when the thermal-arrest data are plotted against the intended compositions, a smooth curve is obtained, as shown in Fig. 1. This is not the case when the data are plotted against the analytical results. It will be noted from Table I that the 12.5 pct Si alloy (melt 4) showed a primary arrest at 577.6"C and the eutectic at 576.l°C. The metallographic examination of this chill-cast plate sample showed a small amount of primary silicon. These results, Fig. 1, place the eutectic at slightly less than 12.5 pct Si and are in rather good agreement with the unpublished Hanford data. In all of the subsequent work, the composition of the A1-Si dipping baths was determined by thermal analysis (spread between the primary arrest and the eutectic temperature) employing 12.5 pct Si and 577.2 °C as the composition and temperature of the eutectic. Material Preparation and Selection of the Techniques: At the beginning of this work, it was anticipated that, owing to oxide film present on the surface of the aluminum, difficulty would be encountered in obtaining rapid uniform wetting of aluminum specimens dipped in the A1-Si bath. The following etchants were investigated as possible methods of providing a thin uniform oxide film on the specimen surface: 1—phosphoric acid (H³O4), 2—fluoboric acid (HBFI), 3—sodium hydroxide (NaOH), and 4—hydrofluoric acid (HF). Tests with sheet .specimens (2x½x0.06 in.) of 2s aluminum prepared with these etchants indicated that the fast uniform wetting required for this work could not be obtained if any oxide film existed on the specimen surface. Tests were then conducted by dipping similar specimens etched in 5 pct NaOH and given a thin

Jan 1, 1956

By K. E. Gray, A. Podio

ABSTRACT Berea and Bandera sandstone samples were impacted with both 3/4-in. and 1/2-in. long wedges, each having a 60° included angle and a 0.05-in. flat, at various confining pressures, with borehole and pore pressures held fixed at atmospheric pressure. Samples were saturated with air, water, glycerine-water, solirol, mineral oil and soltrol-mineral oil mixtures to obtain a wide range of pore fluid viscosity. Penetration depth was held constant at 0.1 in. Dry and soltrol-mineral oil-saturated Berea samples were impacted at depths of penetration from 0.01 to 0.04 in. under 1,000 psi confining pressure to study crater initiation. Results indicate that viscosity of the pore fluid is influential primarily during the early stages of crater formation. Differences in bit force, crater volume and blow energy for tests parallel and perpendicular to bedding were significant, but decreased as the stress state was elevated. Crater volume, blow energy and bit force were nonlinearly related with depth of penetration. Crater volume was nonlinear with energy of blow. Fixed-penetration tests on saturated Berea yielded greater crater volume than did similar tests on dry samples. Differences in the nature of deformation for low values of bit penetration were noted between saturated and unsaturated samples. INTRODUCTION Rock failure during bit-tooth impact and scouring action constitutes a vital part of the drilling process and a difficult problem for researchers. Much study has been devoted to various aspects of the problem, and much has been learned about mechanics of rock failure. However, analytical treatment of drilling at depth remains difficult, partly because there are so many factors involved and because valid simulation of downhole conditions is extremely difficult. Forming individual craters by a bit tooth or chisel impacting, or indenting, a rock mass has been studied by many investigators.1-18 Similarity between single-tooth chisel impact and the corresponding action of a rotary bit has been discussed by Appl and Gatley, Garner, Podio, and Gatlin l8 compared the similarity in single-blow impact tests with microbit drilling data reported by Cunningham and Eenink.l9 Maurerll has used single-tooth impact data to develop a "perfect cleaning" theory of rotary drilling. Individual roller cutter-tooth impact data have been reported by Young. 20 Single-tooth tests in all of the cited literature were carried out on dry rocks. Inasmuch as any subsurface rock of oilfield interest is saturated with some fluid, it seemed desirable to study crater formation in permeable rocks saturated with a viscous pore fluid as a step, however short, toward more realistic simulation of subsurface conditions. This paper presents results of single-blow chisel impact studies on Berea and Bandera sandstones, both dry and saturated with pore fluids of various viscosities at confining pressures to 10,000 psi. EXPERIMENTAL APPARATUS AND PROCEDURE EXPERIMENTAL APPARATUS The same basic apparatus for single-blow chisel impact at elevated stress states, described in earlier papers was used in this study. l6. l8 Fig. 1 shows the complete experimental system; Fig. 2 shows a cross section of the pressure cell, with a sample ready to be impacted. EXPERIMENTAL PROCEDURE Two different rocks, Berea and Bandera sandstones, were used in this study. Both rocks have been used extensively in research, and rock descriptions can be found in a paper by Gnirk and Cheatham.15 Permeability to air of Berea is about 300 md normal to bedding and 540 md parallel to bedding. Bandera had vertical and horizontal air permeabilities of 18 and 57 md, respectively.

Jan 1, 1966

By F. G. Stone

A strain anneal process has been developed for the production of iron tensile test specimens, the gauge length consisting substantially of a single crystal. Since the method has been quite successful and the results of general interest, the process will be described in detail. The essential feature of the method is the continuous, slow increase of furnace temperature during the grain growth annealing treatment. Briefly, the procedure is as follows: I. Heat machined bars to 950°C in vacuum, hold I hr, furnace cool. 2. Strain to 3.5-3.8 pct elongation (axial loading). 3. Anneal, continuously raising furnace temperature from 450 to goo°C at a rate of so0 per day. 4. Hold at 900°C for 100 hr, furnace cool. Tensile test bars with a 1/4- X I-in. gauge section have been machined from 35 in. Armco iron plate and from 3/8 in. rounds of Puron, a high purity laboratory iron. The axes of the test bars were parallel to the rolling direction. During the machining operation the bars were polished in the lathe with No. 600 emery paper, and this polished surface proved satisfactory for subsequent macrographic examination. A micrographic examination of the materials showed that both were high in FeO inclusions, those of the Puron being smaller but much more numerous. An initial vacuum anneal of I hr at 950°C followed by furnace cooling resulted in a ferritic grain size of ASTM No. 3 for Armco and No. I for Puron. Special heat treatments which reversed these initial grain sizes produced no marked improvement in single crystal production after subsequent treatments. The strain for subsequent grain growth was determined by measuring the decrease in diameter of the tensile bar during elongation. The change in diameter could be measured with a micrometer to +0.0001 in., corresponding to an accuracy of 0.08 pct for the elongation. The accuracy of the diameter measurement is also dependent on grain size because of surface roughening during elongation, and for this reason, a No. 3 grain size is preferable. Optimum grain growth was obtained for strains between 3.5 and 3.8 pct elongation. Once this critical range had been cstablished, all tests were held within it, and thus only meager data were obtained on grain growth following strains outside this range. In general, grain size decreased with increasing strain to about 5.5 pct elongation. Grain growth was occasionally ohserved with less than 3.5 pct elongation although this may have been the result of error in measurement. The program control device for the grain growth anneal consisted of a I rpm motor and worm gear drive, operating the dial shaft of a pyrometer controller through a pulley. Dial speeds of 33 and 50°C per day were tried, but the results at the slower speed were not sufficiently better to warrant the increased furnace time. The furnace tube was evacuated at intervals during the run and kept sealed the remainder of the time. When the controller reached 900°C, it was stopped and the temperature held for 100 hr. This eliminated most of the numerous minute crystallites of about 0.5 mm dimension usually visible on the etched surface of the single crystal. Since recrystallization occurs at the A3 point, the top temperature of 900°C provided a 10"

Jan 1, 1949

By H. F. Silliman, Daniel R. Hull, Earl W. Palmer

THE brass-rolling industry has not had a great deal of experience with antimony in its product. There have been some recent excursions with antimony as a corrosion inhibitor in tubes, but in sheet brass it has been regarded with apprehension and generally avoided. This is not to say that [ ] contaminations have never occurred, and probably a great many brass mill men have had their own ideas on the effect of such contamination. Our own views were based upon certain experiences some years ago with strip castings that split lengthwise in the early stages of rolling. The nature of this splitting is shown in Fig. I, from a photograph taken in 1922 as a record of 20 bars of 65-35 common brass made with an antimonial brand of copper. These bars were cast 6 ¾ in. wide by 1 in. thick by 45 in. long. In the first pass through the rolls, 19 of the 20 split lengthwise throughout their length, while each half curved outward in a wide arc as it emerged from the rolls. [ ] In those days, if splitting was not a frequent occurrence, it was not unfamiliar. One can recall periods of short duration when large amounts of common brass would behave in this way. There was nothing imaginary about these spells. The affected metal would split lengthwise in the breaking rolls, and no maneuvering of mill practice made any difference. The condition would descend like a plague, demoralize the mill for several days, and disappear. It is doubtful if anyone knew the cause-however many explanations may have been current. In 1921 a quantity of split brass was traced to the use of fired small-arms

Jan 1, 1943

By T. R. A. Davey

The fundamental principles by which bismuth may be removed from lead by pyrometallurgical processes are enumerated. Qualitative discussion of the phase diagrams concerned is followed by presentation of quantitative diagrams. Brief mention is made of the practical aspects. Data presented show how chemical lead (<0.005 pct Bi) may be produced by the Jollivet, Dittmer, and Kroll-Betterton processes. BISMUTH is an element whose properties are very similar to those of lead, and its minerals are associated to a greater or lesser extent with nearly all the major lead ore deposits of the world. In consequence, the lead produced contains bismuth unless a special debismuthizing process is practiced. There does not appear to be any published comprehensive review of the effect of bismuth as an impurity on the properties of lead, and there is some uncertainty as to the beneficial or detrimental effects of small amounts of bismuth in lead used for particular applications. Standard specifications of most countries stipulate a maximum bismuth content of 0.005 pct for chemical lead. With one exception, this specification is met only by lead producers whose ores are relatively bismuth-free, or whose refineries are electrolytic. In lead for certain applications a higher bismuth content is preferred by some fabricators.&apos; In contrast to the refining for silver, copper, and antimony, the refining for bismuth does not usually result in a large overalil economic gain from the sale of byproduct. Thus, debismuthizing is customarily practiced only if market conditions demand a lead with a bismuth content lower than that produced by classical refining; i.e., softening, desilverizing, and zinc refining. Until this century, debismuthizing was carried out only a:; an incidental result of desilverizing, as later described. This century has seen the development of the Betts electrolytic process—the only successful one of many electrolytic processes proposed and patented —and a number of precipitation processes based on the pioneering work of Kroll,&apos; although only one of these, the Kroll-Better ton process,&apos; is in wide commercial use today. It is proposed in this paper to deal only with the pyrometallurgical processes, excluding those based on aqueous electrolysis. Historical Background Prior to 1833 silver (and incidentally bismuth) could not be removed from lead. To recover silver from rich bullion, the only course available to lead refineries was to cupel the bullion, forming a slag of litharge. The first slag tappings or skimmings, on reduction, yielded soft lead of very low silver and bismuth contents. Intermediate skimmings yielded a lead of somewhat higher silver and bismuth contents, which could if desired be recupelled. The last skimmings yielded a litharge very high in bismuth, which could by successive oxidation and reduction cycles be separated into high purity bismuth, and lead returns. This oxidation reduction process, with modern operating techniques, can still be used today to produce a portion of a lead refinery&apos;s output of very low bismuth content, as discussed later. In 1833 Pattinsone discovered that lead bullion could be purified of silver and bismuth by fractional crystallization, the primary lead crystals formed by partial freezing being purer than the melt. Repeated processing in pans produced a lead containing as little as 0.02 pct Bi. The simple explanation of this

Jan 1, 1957

By K. E. Brown, J. P. Brill, A. R. Hagedorn, T. C. Doerr

A recent correlation for multiphase vertical flow by Hagedorn and Brown1,7 has been used to examine the effect of numerous variables such as pipe size, gas-liquid ratio, liquid flow rate, liquid viscosity, liquid surface tension, oil API gravity, water cut, etc., on flowing pressure gradients. Most previous correlations were derived by using a form of the general energy equation which assumed negligible changes in kinetic energy. Under certain flow conditions this can lead to serious errors in predicting pressure traverses. Examples of traverses calculated both with and without the kinetic energy term are included here. The Chew and Connully correlation for calculating changes in viscosity with changing pressure and temperature has been extended so that the effect of a changing viscosity with depth on pressure gradients can also be predicted. Examples illustrating the effect of tubing size show the importance of this correlation in determining pipe sizes for initial well completions. Limitations on production rates in small pipe sizes from excessive friction losses can be predicted with greater accuracy. The combined use of a vertical-flow correlation with a horizontal-flow correlation provides a method for determining the maximum flow rate possible from both flowing and gas-lift wells. Examples are included to illustrate application of the combined use of vertical and horizontal-flow correlations in optimizing production rates and minimizing excessive costs from over injection of gas in gas-lift wells. INTRODUCTION The problems of multiphase vertical and horizontal flow are immediately encountered in any producing well. Fig. 1&apos; shows three stages of production: flow in porous medium, vertical flow and horizontal flow. All three stages affect the production rate from a well. If we are confronted with a particular well and consider only the variables involved in the vertical and horizontal stages of Fig. 1, we should be capable of calculating the flowing bottom-hole pressure necessary to produce a particular flow rate. A change in any of the variables results in a new solution to the problem. Recent approaches in developing horizontal and vertical-flow correlations have improved to the extent that the solution can now be obtained with more confidence than previously. VERTICAL AND HORIZONTAL FLOW CORRELATIONS Since Poettmann and Carpenter&apos;s&apos; original work in multiphase vertical flow, there have been many additional vertical-flow correlations developed which have greatly improved the accuracy of pressure-loss calculations. These

Jan 1, 1967

By J. Bruce Wagner, Roger L. Levin

Integrated forms of two solutions of Fick&apos;s second law for the movement of a plane interface through a sample of wustite, and for diffusion into a semi-infinite slab of wustite, are shown to yield nearly identical values of the chemical diffusion coeffcients of cation vacancies in wustite, over the temperature range 900° to 1100°C. The chemical diffusion coefficients, the values of D obtained for the propagation of a concentration gradient through samples of undoped and doped wustite, are obtained from the equations It is becoming increasingly important in metallurgical practices to understand the role of the chemical diffusion coefficient, i.e., the diffusion coefficient of a species across a concentration gradient. During the first stages of sintering, one of the mechanisms by which the bonds between neighboring particles develop is by volume or bulk diffusion. This diffusion coefficient as deter- where ?m is the weight change at any time t, ?W is the total weight change at t =8, A is the area of the specimen, and AC is the total change in the cation concentration after the establishment of equilibrium, as determined by reduction experiments in different carbon monoxide -carbon dioxide mixtures within the limits of existence of the single-phase field. mined from the standard equations for volume diffusion during sintering is actually a chemical diffusion coefficient, and it has been observed to be many times larger than the self-diffusion coefficient as determined on the same materials by experiments using radioactive tracer techniques. Kuczyn-ski1 has noted that, if the controlling mechanism of sintering of A12O3 in an oxidizing atmosphere is the diffusion of oxygen, then this diffusion coefficient as measured from sintering rates is about 2.2 x 104 higher than the self-diffusion measurements obtained by tracer techniques. He has also reported the diffusion coefficient obtained from the rate of sintering of Fe2O3 powder to be about 10 6 times faster than the self-diffusion coefficient of

Jan 1, 1965

By A. E. J. Engel

INDUSTRIAL talcs and ground soapstones both include earth materials of different chemical and mineral compositions. In general, the industrial talcs are composed of silicates that contain appreciable amounts of magnesia. Generally talc, the mineral, is a predominant or at least common constituent. Talc, the mineral, is a hydrous magnesium silicate, with a suggested theoretical formula H2Mg3 (SiO3)4 or H2O.3MgO.4SiO2, which postulates 63.5 pct SiO2, 31.7 pct MgO, and 4.8 pct H20.11 Actually different single grains or leaves of pure talc have variations in water content ranging from 3.5 pct to more than 7 pct, as well as slight differences in the proportions of MgO and Si02.16 Only a very small percentage of the ground industrial talcs produced in the United States approaches the composition given above (see Table 1). The purer talcs invariably occur as alteration products of magnesium carbonate rocks. Some of these relatively pure talcs include compact, massive types largely mined in California, which are designated as steatite.38,58 In general, steatites cannot contain in excess of 1.5 pct CaO, 1.5 pct combined FeO and Fe203, and 4 pct A1203. The less pure varieties of massive talc and mixtures of magnesian silicates are commonly called soapstones, or merely talc. Many industrial earth products classified as talc or as soapstone contain a variety of minerals, especially serpentine (H4Mg,Si2O9), chlorites (hydrous magnesium, iron, aluminum silicates), tremolite (Ca2Mg5H2[SiO3]8), anthophyllite ([MgCa]SiO3), diopside (CaMg[SiO3]2), and quartz (SiO2). The carbonates calcite (CaC03), dolomite (CaMg[CO3]2), and magnesite (MgCO3) are also present in some industrial talcs and soapstones. Some of these minerals, as well as sulphides, sulphates, and iron and manganese oxides, if present at all or in excess of minute amounts, may alter the composition of the industrial talc sufficiently to restrict materially its use or to lower or destroy its value. These factors are discussed in a subsequent section of this chapter.

Jan 1, 1949

By R. W. Raymond

The important question of the metallurgical value of the coals of the Rocky Mountains and the Pacific Coast is to be settled, of course, by practical experiment. Meanwhile, as I have had occasion to point out, the proximate analyses of these coals throws little light upon it, and is, indeed, likely to mislead the metallurgist, if he compares it with the results of similar analyses upon bituminous and semi-bituminous coals. With the view of showing how large a proportion of the material usually classed as(" volatile matters " consists of combined water, or oxygen and hydrogen presumably in chemical combination, I have collected a number of ultimate analyses from various sources, in the following tables. The numbered analyses in the first table are as follows: No. 1. Monte Diabolo coal—Analyst, H. S. Munroe, Col. School of Mines. 2. Weber Canon, Utah, " " " 3. Echo Canon, " " " " 4. Carbon Stat&apos;n, Wyoming, " " " 5. " " " " " 6. Coos Bay, Oregon, " " " 7. Alaska, " " " 8. " " " " 9. Canon City, Colorado, " Dr. T. M. Drown, Philadelphia. 10. Baker Co., Oregon, " " " 11. Blockcoal,SandCr&apos;k,Ind., " Prof. E. T. Cox. This table affords some suggestive comparisons, to facilitate which a remark or two, explanatory of its construction, will be useful. In the ultimate analysis of coals, the proportions are frequently calculated (as, for instance, in the report for 1872 of Prof. Cox, State

By T. Price, H. A. Holl, A. P. Greenough, A

UdIN, Shaler, and ulff&apos; first used wires for the determination of the surface energy of a solid metal. A gage length was marked by tying knots in the wires, which were then suspended in a cylinder of the same metal, heated in an inert atmosphere for the appropriate time, cooled to room temperature, and finally removed from the furnace so that the lengths of the wires could be measured. With iron wires, difficulties associated with deformation during the phase changeszp3 made it necessary to measure the gage lengths at the tem-

Jan 1, 1964