Search Documents

By John C. Shyne, Eric R. Morgan

WHEN temper rolled low carbon sheet is stored at room temperature before use, changes take place in its mechanical properties. This phenomenon is known as strain aging. Normally these changes are observed by means of Olsen ductility and Rockwell B hardness tests but' unfortunately such tests are relatively insensitive. Strain aging can be readily observed in the laboratory by means of tensile tests. The tensile test method is even more sensitive if the aging is allowed to take place in specimens which have been prestrained in tension rather than by cold rolling. In fact one of the great benefits of commercial temper rolling is that it introduces a residual stress pattern which tends to mask the effects of strain aging when the sheet is finally used in a pressing operation. Curves B, C, and D of Fig. 1 illustrate the changes that take place during the aging of commercial rimmed steel at room temperature following straining in tension, curve A, Fig. 1. The first important change that can be observed is an increase in the stress required to produce plastic flow. This increase is, in this paper, called the aging index. As aging proceeds and the aging index increases, there is also an observable return of the yield point, an increase in the ultimate tensile strength, and a decrease in elongation to fracture. The results of strain aging in deep drawing steel manifest themselves as stretcher strains (L?ders bands) buckling, 2nd tearing. In deep drawn parts such effects are undesirable and strain aging is a serious problem. The rate of strain aging of a steel depends upon its composition and prior mechanical and thermal history? but for most temper rolled ope

Jan 1, 1958

By Dr. O’Neil Thomas J., Donald W. Gentry

"October. This is one of the peculiarly dangerous months to speculate in stocks. The others are July, January, September, April, November, May, March, June, December, August and February." -Mark Twain Although the preceding chapters describe the type of preliminary evaluation frequently performed in the mining industry, it has been assumed that input data are known with certainty-clearly an enormous simplification. In reality, estimates of ore grade, mining cost, metal price, etc., are subject to varying degrees of uncertainty due to the inability to predict the future with much precision. Management would probably not, for example, be equally attracted to two projects each offering a 20% DCFROI-one for a new gold venture in Nevada and the other for an undersea manganese nodule operation in the Pacific. The high risk with the latter investment tells the obvious; there is more to investment decision-making than a deterministic analysis using "best estimates" of input parameters. The science of decision theory normally distinguishes between decisions under uncertainty, where probabilities of various outcomes are unknown; and decisions under risk, where such probabilities can be estimated. The first case is rarely en- countered in practical capital investment analysis in mining, so the remainder of this chapter focuses on that class of problems where rational probability distributions for the future states of input variables can be estimated. RISK IN MINING Risk in the context of this chapter is the unforeseen deviation of individual cash flows from expected values for a capital project. For a mining venture, the source of this uncertainty could be any number of factors relating to such items as ore grade, ore reserve tonnage, operating costs, product prices, etc. With conventional *Adapted from O'Neil, T.J., 1979, "Procedures for the Preliminary Financial Evaluation of Metal Mining Ventures," Computer Methods for the 80s, A. Weiss, ed., AIME, New York, pp. 556-573.

Jan 1, 1984

By Jennings S. Cox

The following notes, prepared in 1908, as the result of a personal examination and extensive explorations under my direction in 1906, have been revised and greatly augmented after two subsequent visits and further explorations in 1910. The hard iron-ores of the south coast of Oriente Province, in the island of Cuba, have been known for many years, in fact one mine has been in operation for more than 20 years; but it is only within the past four years that the large mantle-deposits of brown ores of the north coast have attracted serious attention. A. C, Spencer' has described these ores in a paper, entitled Three Deposits of Iron Ore in Cuba, which refers to the Mayari, Moa, and Cubitas deposits. C. M. Weld,2 in a scholarly paper, The Residual Brown Iron-Ores of Cuba, has discussed the character and possible genesis of these deposits with particular reference to the Moa field, calling attention also to the Taco and Navas fields in addition to those described by Spencer. Descriptive articles with reference to the Mayari field, and a few words about the Moa deposit, have also appeared3 It is the purpose of the present paper to give some account of the exploration of the Moa deposit arid to call attention to its commercial importance. Location. The Moa district is situated on the north coast of the Province of Oriente, which is the most easterly province of the

Jan 1, 1912

By Paul R. Wieber, Atam P. Sikri

This paper describes the U. S. Energy Research and Development Administration's (ERDA) program to develop in situ coal conversion processes, especially gasification. The potential of this technology, the technical directions being explored, and the program strategy to carry the process concepts toward commercialization are emphasized. The geographic location of the U. S. coal resources and a market analysis are described. Commercially successful in situ coal processes could add over a trillion tons of coal to the U. S. coal reserves. The economics of these processes is compared with surface gasification. Independent studies show this process to be 25% cheaper than surface gasification for Western coals. The major projects are briefly described. The Linked Vertical Well process is in the most advanced stage and shows great promise. The last test produced a low-Btu gas averaging 171 Btu per standard cubic foot for average production rates of 8.5 million standard cubic feet per day. The other projects are Packed Bed, Longwall Generator, and Steeply Dipping Beds. Unique factors of the process development are discussed which may lead to commercial processes in the near term. A development strategy is proposed by which this technology could be commercialized before 1985 with potentially lower gas prices and lower environmental impacts, relative to mining plus surface gasification.

Jan 5, 1978

By J. P. Hirth, C. S. Hartley

A simple graphical technique is presented for rapidly determining the ratio of resolved shear stress on slip systems in single crystals to the applied stress (Schmid factor) for various simple states of stress. Master plots are presented which, when used in conjunction with an appropriate stereo-graphic projection, allow one to determine the Schmid factor for all slip systems in a crystal of given orientation. It is shown that one such plot suffices for simple tension or compression, flex-ural bending, and biaxial compression, while a combination of two different plots must be used for torsion and simple shear. STUDIES of the deformation behavior of single crystals are most valuable when the applied stresses are resolved onto the various slip systems of the crystal. A careful study of the available slip systems and proper selection of the state of stress used and the specimen orientation can then yield quantitative information about the probability of specific dislocation reactions, the strength of barriers to plastic flow, and the mechanisms of yielding and flow in general. It is the purpose of this work to analyze some common states of stress used in deformation studies and to present a simplified way of determining for these cases the ratio of the resolved shear stress on the slip systems to the applied stress (Schmid factor). I) CALCULATIONS We first define two orthogonal coordinate systems: one based on the specimen geometry (a right circular cylinder of radius, R, is considered here) and one based on the particular slip system of interest. The unit vectors and angles specifying the two coordinate systems and the relationship between them are listed in Table I. The relationships among the various angles and unit vectors are shown on a stereographic projection in Fig. 1. The transformation matrix between the (XI X2 X3) and (x'1 x'2 x'3) system is x1 x2 x3 X'1 a11 al2 a13 x'2 a21 a22 a23 x'9 a31 a32 a33 where in this case the direction cosines aij are given by a11 a12 a13 aij = a21 a22 a23 a31 a32 a33 sin 0 cos F cos 0 sin F cos 9 = -cos 0 cos F sin 0 sin F sin 6 [1] 0 -sin F cos (p In terms of Eq. [I.], the stresses sij, referred to the slip system, are determined from oij, referred to the specimen axes, by1,2

Jan 1, 1965

By C. E. Nelson

THE purpose of this discussion is to outline briefly the practices commonly followed in this country for the melting and refining of magnesium and its alloys. The processes used for the various forms of primary magnesium, as far as there are differences in the physical shape or behavior, will be discussed. The refining of general fine scrap or secondary magnesium was presented in an earlier paper.1 Inasmuch as the use of fluxes is an essential part of all the melting and refining processes, the principal aim of this paper will be to deal with these in sufficient detail to point out their unique characteristics, in order to make their use more effective. TYPES OF MELTING PRACTICE All melting and refining processes for magnesium and its alloys require the use of fluxes. These fluxes have a magnesium chloride base and other halide salts or oxides are added to give a density or behavior exactly suited to the particular melting practice. The successful handling of magnesium depends upon the proper use of the correct fluxes. There are four general methods of melting, summarized in the following paragraphs and treated in more detail in the section on Melting and Refining. Open-pot Method The open-pot method makes use of No. 230 flux.* The flux provides protection during melting and a molten pool of flux into which the solid magnesium melts. It is stirred through the molten metal bath and agglomerates oxide or similar foreign bodies; then on quiet standing separates away, leaving the refined metal ball floating in an encircling layer of molten flux. It forms only a thin fluid film over the surface of the molten metal, which may be parted for hand-ladling processes and tends to cover the metal again after the ladle is removed. A very light dusting of the pot surface with fresh flux immediately after the ladle is removed is usually desirable. The open-pot method is used generally in the following processes: (I) alloying and secondary smelting in the production of ingot, (2) in sand foundries for premelting and to a smaller extent for the production of small castings requiring hand ladling, (3) in permanent-mold founding for premelting and also direct ladling to castings, (4) for continuous methods of preparing metal in the production of billets or ingots from which wrought products are fabricated, (5) in general scrap recovery. Crucible Process The crucible process makes use of No. 310 flux, which has the property of being thinly fluid at the start, to provide protec-

Jan 1, 1944

Discussion of the papers of FREDERICH LAIST and HAROLD W. ALDRICH, FREDERICH LAIST and F. F. FRICK, W. L. AUSTIN, and STUART CROASDALE, presented at the Salt Lake meeting, August, 1914, and printed in Bulletins No. 91 and 92, July, and August, 1914. R. C. CANBY, Wallingford, Conn. (communication to the Secretary*). -Apropos of the experimental reduction of copper from cuprous chloride by fusion with ground limestone and coke, as described by Messrs. Laist and Frick, and also proposed for use at Chuquicamata., it might be of interest to refer briefly to the experience at Argentine, Kan., in the smelting of the suboxide of copper (as produced in the Hunt and Douglas process) containing appreciable quantities of chlorides. In the Engineering and Mining Journal of June 10, 1911, I. gave some account of what had appeared to be crucial difficulties with the Hunt and Douglas process, and how the filter-press difficulty had been so rapidly overcome after my discovery of the effect of the sodium salts in the leaching solutions. I also described the effect of the cupola furnace gases upon the lime rock with which I had replaced the coke in the absorption tower, which apparently showed the presence of considerable-chlorine, clue to the imperfect conversion of the subchloride to suboxide, as well as that clue to the difficulties of washing thoroughly the suboxide with the means provided, and also to the presence of chlorides in the cement copper which was smelted With the suboxide. The fumes from the cupola, when issuing direct into the atmosphere, were very dense and white, except when a hot furnace top caused a reddish tinge due to dust. These, fumes had a peculiarly suffocating effect, so that when they were blown over into the town the population suffered the greatest actual distress, not the mere annoyance which would have been clue to a disagreeable odor. The absorption tower had been built at the instance of the city authorities to abate this nuisance, and not with the idea of making any additional metal savings. A serious feature in connection with the Argentine experience with the Hunt and Douglas process was, that it had been implicitly assumed that there could be no metal loss in the Hunt and Douglas process itself, and that all attempts to locate the ruinous copper losses which were accumulating in the metallurgical accounts were devoted to the roasting department. It is possibly unfortunate for metallurgical advance along these particular lines that just about the time of this discovery of this previously unsuspected volatilization loss, in the smelting of the suboxide, the Kansas City company made a contract with the Western Union Telegraph Co. for its supply of copper sulphate and the Hunt and Douglas

Jan 11, 1914

By E. Beril

This may be a most unnecessary paper—from what does crude oil come and how was it formed. Many people, inside and outside of the petroleum industry, believe that we have actually enough oil, and that we can easily produce very important products from this extremely valuable raw material. The writer believes, however, that the answer to this question concerning the parent material and the formation of oil is of broader interest, because it may be that from the answer to these problems it would be possible to get answers to other important industrial questions. Therefore, a study in this line seems to be justified, and the writer will submit some of the results which he has collected during more than ten years with many very capable collaborators, to whom his thanks may be expressed on this occasion. Older Theories There is no doubt that plants were the parent material of coals, but opinion is divided as to the parent material of crude oil and asphalts. One group of specialists believed that they were formed from dead fish. The hydrocarbons of crude oil were formed by the splitting off of CO² from fatty acids formed by the saponification of the fat (glycerides) of fish. Enormous quantities of crude oil are present in many places on the earth, very often in several nonconnected horizons at the same location. This could hardly be explained by the so-called "catastrophe theory," which states that fish died through the entrance of salt water into fresh water, and vice versa. Furthermore, this theory cannot explain the presence of aromatic hydrocarbons, which can be found in nearly all oils, especially in the oil of the Netherlands Indies, which has more than 50 per cent of aromatics. Geological and chemical observations both lead to the belief that the temperature of formation of asphalt, crude oils and coals, perhaps with a few exceptions, did not exceed 200° C. Chlorophyll and haemin derivatives, which decompose above 200° C., have been found in all these materials by Treibs and others. Thermodynamic considerations show that the temperature necessary for the conversion

Jan 1, 1938

By A. T. Janssen

Production planning of direct-shipping ore from a number of relatively small deposits serves to sequence development and mining of these deposits so that both long- and short-range demand can be met while the timing of development cost is such that the average annual rate is minimized. Hand-computed methods have the disadvantage that they require substantial effort and time and cannot be exhaustive. The application of operations research and computers not only overcomes these disadvantages, but opens up additional applications, such as feasibility studies involving alternative mining strategies and changes in the ore market. The method employed concerns linear programming and specifically the Big-M algorithm applied to the variant on the simplex technique with penalties applied to deviations from the desired ore grade. Acceptable 20-year production schedules could be generated in relatively little time, i. e. , in less than 200 seconds for the central processor of the Control Data Corporation 6400 system of the University of Colorado in Boulder.

Jan 1, 1969

By T. N. McVay, E. E. Creitz

Rather large amounts of titanium minerals and some zircon and monazite are being recovered from dune sands about I. miles west of Jacksonville Beach, Fla. The Mining Branch of the Bureau of Mines, Southern Experiment station, has been interested in developing additional large deposits of similar sands in other areas of Florida. The results of a field study have been published1 concerning the sands occurring on Trail Ridge which runs north and south about 30 miles southwest of Jacksonville. This investigation was undertaken in order to identify the opaque titanium minerals occurring in Trail Ridge and because of the economic importance of Florida titanium minerals. Nature of the Problem The minerals present in the heavy fractions (sp gr > 2.94) of the sands are principally opaque minerals; staurolite, zircon, sillimanite, tourmaline, kyanite, rutile, a small amount of corundum, traces of the zinc spinel gahnite and garnet. Epidote, monazite, hornblende and ti-tanite are present in other dune sands but these minerals were not noted in the samples collected on Trail Ridge. All of the minerals except those which are opaque can be readily identified by the usual petrographic methods. However, Opaque minerals cannot be examined satisfactorily by transmitted light. Polished sections of the opaque-mineral grains were examined but these sections did not furnish useful information. Consequently, it was necessary to use means other than the usual petrographic methods to identify them. Previous Investigations of Heavy Minerals in Florida Sands Martens2 has described the heavy minerals in the Florida beach sands and has classified the opaque minerals as ilmenite with minor amounts of leucoxene. Miller3 studied a number of sands collected by Ross and Mertie in Florida. He states that the material from the Florida beach and dune sands that commonly has been called ilmenite has essentially the chemical composition of the material that has been called arizonite.4 The x ray diffraction patterns of several samples indicated that the supposed ilmenite is essentially amorphous, with only weak lines corresponding to ilmenite, and hence the material is unlike the type of arizonite from Arizona. Opaque Titanium Minerals Rutile is essentially titanium dioxide. However, as pointed out by Dana,5 important amounts of Fe+2 and Fe+3 as well as Cb and Ta are reported in some analyses.

Jan 1, 1949

By C. Feng, C. Elbaum

AN investigation of the fracture plane of titanium, containing 0.5 wt pct to 1 wt pct 0, was recently carried out by fracturing large-grain specimens in a tensile jig at room and liquid air temperature. The experiments were carried out on strip specimens 3 to 5 mm wide, 2 mm thick and about 100 mm long. The specimens consisted of several grains, each occupying the entire cross section of the strip and extending over a length varying from 5 to 20 mm. These specimens were prepared by a method described elsewhere.' The identification of the fracture plane was possible in twelve of approximately thirty crystals investigated. In some cases severe local distortion took place near the fracture and prevented identification of the fracture plane. On, at least, three occasions the fracture propagated in a helicoidal

Jan 1, 1959

By P. R. Kalischer

IN the production of alloys by powder metallurgical processes it is often necessary or desirable to include one or more components that tend to form very stable oxides Included in this group of metals are aluminum, manganese, magnesium, silicon, and a few others In many cases it is not necessary for the sintered compact to have full density and the other physical characteristics of a cast alloy and in that event no undue precautions need be taken If, however, it s required that the sintered part be entirely homogeneous, and have maximum density and physical properties, some method must be found to reduce the surface films of oxide, which are always present on the metals, and for the metals mentioned above this is always extremely difficult, if not impossible Since the production of high-density alloys is of particular interest to powder metallurgists, some experiments were undertaken to devise methods of reducing the refractory oxides For this work, alloys of iron, nickel, and aluminum were chosen because aluminum oxide is one of the most stable oxides and because these alloys in the right compositions form excellent permanent magnets All of the pertinent properties of the magnets could be accurately and delicately measured by density measurements and magnetic tests of sufficient scope to give a complete demagnetization curve From such a curve the maximum coercive force, residual magnetism, and energy products could be obtained and compared with the same properties for a cast material Any lack of homogeneity, density, or solid diffusion would be immediately apparent as a decrease in the magnetic properties NATURE AND REMOVAL OF SURFACE BARRIERS The early work of the present investigation was based upon published processes In the published information it was claimed that by intimately mixing iron, nickel, and iron-aluminum alloy (50 per cent Fe, 50 per cent Al) powders, compressing such a mixture into the desired shape and size, and then sintering (heating to a temperature below the melting point of the component metals) in hydrogen at 1200ºC or higher, a sound, homogeneous article could be made having the desired physical size, shape, and strength, and good magnetic characteristics However, this early work showed clearly that something in the powder compress was inhibiting diffusion and the process was almost entirely unworkable In the initial phase of the investigation samples of iron powder, nickel powder, and iron-aluminum alloy powder were pressed into separate bars and sintered in hydrogen Both the iron and nickel powders sintered

Jan 1, 1941

By F. R. Brotzen, J. Taranto

SEVERAL investigators have computed stacking-fault concentrations from X-ray diffraction data.'-' The method generally employed relates the line shift to the stacking-fault probability. In this investigation platinum filings of 99.99 pct purity screened to -325 mesh were studied after having been subjected to various annealing treatments. The lines were measured on a General Electric XRD-5 spectrogoniometer using CuK, radiation. The centroid of the broad reflections was determined by the method proposed by pike.' The stacking-fault probability was calculated by the formula given by Warren and warekois,3 with the assumption that all stacking faults were on the (111). Various high-angle reflections were used, but most data collected refer to the shift in the (400) reflections. When the filed platinum powder was annealed at 1200°C for 20 min the stacking fault concentration was too small to be detected. The stacking-fault probability in freshly filed specimens, as determined by the line shift relative to the annealed specimen, was about 0.016, Fig. 1. If the faults would be created only by extended dislocations, the dislocation density in the filed specimen would be about 3X1012 cm-2. The average stacking-fault width of about 21 which was used in this computation, is that given by Thornton and Hirsch.7 The mechanism by which stacking faults are annihilated during annealing is not yet fully understood. The isothermal results obtained do not seem to support the simple hypothesis of a first-order decay. On the other hand, the analysis by Kuhlmann, Masing, and Raffelsieper8 for the loss of dislocations during recovery agrees much better with the experimental data of this investigation. This analysis yields an activation energy of 29 ± 8 kcal per mol for the disappearance of stacking faults in cold-worked platinum during annealing. Even if one takes into account the lack of accuracy inherent in this X-ray method, the activation energy found is substantially less than that of self-diffusion in platinum, i.e., 61.6 kcal per mol.9 The results therefore suggest that processes other than dislocation climb, which involves the activation energy of self-diffusion, are responsible for the loss of stacking faults in platinum during annealing. The broad reflection lines became sharper early in the recovery process, Fig. 1. The sharpening occurred well before the stage during which stacking faults disappear. This lends support to Nowick's10

Jan 1, 1962

By P. R. Bradley

This paper gives a brief history of the mining and milling operations in the Juneau gold belt, and a general description of the geology of the district, followed by a suggestive discussion of the general problem of sampling gold ores and a detailed description of the mining methods used in the Alaska Juneau mine. The paper indicates that variations in assaying ore similar to that from the gold belt are unavoidable on account of the erratic distribution of the gold. A caving system that accepts dilution was adopted for the Alaska Juneau mine; the ore is sorted and the final mill feed has nearly twice the assay value of the ore trammed. THE property of the Alaska Juneau Gold Mining Co., covering the Juneau gold belt for over a mile in length, consists of 136 claims and 24 mill sites; these are near Juneau, Alaska, in what is known as the Harris mining district.

Jan 3, 1924

By Paul A. Flinn, Jean-Marie Robert Genin

The MCssbauer effect was used to study the distribution of carbon in Fe-C alloys of high carbon content during room-temperature aging. In freshly formed rnartensite the carbon distribution is approximately random; carbon clustering occurs dun'ng aging. In the retained austete the carbon atoms are isolated, suggesting an efiective repulsion; and no rearrangement during room-temperature aging is evident. The kinetics of the carbon clustering in martensite has been studied in detail at 0" . 10". and 20°C. The time and temperature dependence observed is sinzilar to that reported for a variety of other aging effects, such as resistance change, hardness increase, and recovery of internal friction. The stabilization of the martensite kransformation also appears to be related to the clustering effect. DESPITE extensive efforts since the early days of Reaumur, the mechanism which provides the strengthening of steel remains controversial in many cases for several reasons: 1) The structure of as-quenched martensite is not well-determined. 2) Experimental methods capable of distinguishing between various hardening mechanisms are not well-developed. 3) The temperature of formation of many low-alloy martensites is so high that the martensite formed during quenching may be already tempered to some extent before any observation. Among all the hardening phenomena, the most puzzling one occurs at room temperature, where no structural changes have been detected by the usual methods of X-ray diffraction or electron microscopy. However, a new and more sensitive technique became available with the discovery of the MBssbauer effect. This effect makes possible the detection of changes in the local environment of iron atoms in solid solution. It has been extensively used in the study of substitutional alloy systems, for example, Fe-Al,1 Fe-Si,2,3 Fe-Rh,4 and Fe-Ni.5 Making use of the possibility of obtaining new structural information, we undertook an investigation of the aging of high-carbon Fe-C martensite to follow the structural changes involved in the aging at room temperature. Preliminary results6 showed that a clustering of the carbon atoms occurs with time. A systematic study of the kinetics of the process showed a striking similarity to the kinetics of stabilization of the marten-sitic transformation, thus suggesting further investigation of the relationship. EXPERIMENTAL TECHNIQUE To eliminate difficulties with the aging of martensite prior to the first experimental measurements, we needed an alloy with an M, temperature not above room temperature. Other investigators7 were misled by results obtained on alloys which transformed above room temperature and underwent structural changes prior to the first Mossbauer measurements. Winchell and cohen8 dealt with this difficulty by using a third element, nickel, to depress the MS below room temperature. The presence of nickel did not seriously interfere with hardness or resistivity measurements, but it would complicate the interpretation of the Mossbauer data by increasing the variety of iron environments. We chose, therefore, to obtain the necessary lowering of the M, simply by increasing the carbon content. After the first quench to room temperature, our specimens are retained austenite, which we later quench into liquid nitrogen. The martensitic transformation takes place suddenly, so that the as-quenched condition of the samples is retained, since the temperature is low enough to prevent any carbon diffusion. A Massbauer spectrum at 77°K can be taken and analyzed; after an appropriate up-quenching to the aging temperature, a new Mossbauer measurement at 77°K can be made. Fig. 1 shows a typical cycle of experiments. The samples were foils 25 p thick of high-purity

Jan 1, 1969

Jan 1, 1947

Jan 1, 1947

By A. M. Gaudin, D. W. Fuerstenau, M. M. Turkanis

SOLUBLE silver salts are effective activators for flotation of sphalerite with potassium ethyl xanthate as collector.' Since sphalerite takes up large quantities of silver ions rapidly," investigation of this system appeared fruitful for studying the mechanism of sphalerite activation and deactivation. Experimental data presented here comprise studies of the mechanism and rates of activation and deactivation of sphalerite with silver and cyanide ions. A 20-lb sample of sphalerite from Ottawa County, Oklahoma, was handpicked, crushed, screened, hydrosized to produce a 65/100-mesh fraction, and purified by electrostatic separation. The sphalerite was then leached with benzene and absolute ethyl alcohol to remove possible organic contaminants and with 0.1 M NaCN to remove any copper that might have been picked up during screening. The benzene had been specially purified by grinding with fine sphalerite for 12 hr to remove trace impurities that might have had a specific affinity for sphalerite. Finally, the mineral was washed, dried in flowing nitrogen, and stored in large ground-glass stoppered weighing bottles under a small nitrogen pressure.

Jan 1, 1957

By C. H. Fulton

Page Introduction........................... 280 Distillation Products from Reduction of Zinc Ore........... 281 Preliminary Investigations..................... 290 Equilibrium of Reaction Zn + CO2 + ZnO + CO in Temperature Range of Condensation........................ 293 Requisites for Successful Condensation................ 299 Discussion............................ 300 Introduction The study of the condensation of zinc from its vapor was undertaken to shed light on certain problems encountered in large-scale electric zine-furnace work. recently conducted. It is a matter of common knowledge that one of the disadvantages of the arc type, electric zinc furnace, is the production of a large amount of blue powder and proportionately little liquid spelter, for, as stated by Stansfield,l "A notable defect in the electric smelting of zinc ores is the difficulty experienced in obtaining the distilled zinc in the liquid state; ...... when zinc ores are smelted electrically, very little liquid metal is commonly obtained, nearly all of the zinc being in the state of powder." This difficulty was not encountered in the electric furnace used12 the main difficulty being the destruction of the fire-brick lining of the large condenser, in certain parts, and the formation of .some oxide and dross coatings on the condensing surfaces. The reason for these difficulties could readily be explained by the infiltration of air whenever the condenser was changed from one retort base to the other, the zinc absorbed in the fire-brick forming oxide and causing rupture by its expending volume. Two facts, however, tended to disprove this theory for the rupture of the fire-brick lining: first, the large distilling retort, lined with fire-brick, which was shifted from charge to charge on alternate bases at temperatures between 1200 and 1300 C., fully exposed to the air, showed no signs of disintegration whatever; second, marked disintegration in the condenser occurred .only in places that were at tempera-

Jan 1, 1919

By J. S. Ross

Although the opinion has prevailed for several years that bottoni-hole choking under certain flow conditions should effect an increase in flow efficiencies, the use of bottom-hole chokes until recently has been limited in application mainly because of mechanical difficulties encountered in their construction. Within the past year, however, bottom-hole choking, through the development of a removable type of choke, has been applied successfully under various conditions of flow in many Mid-Continent fields. The observation of these field tests indicates that bottom-hole choking, although not applicable to all flow conditions, has an important place in the operation of oil and gas wells. This paper gives briefly the conclusions drawn from the data obtained from the experiments with this bottom-hole choke under various flow conditions, and a description of the choke and its operation. Purpose of Bottom-hole Choking Since, in a normal well, the velocity with which the column of gas is moving generally has a direct bearing upon the quantity of oil it can lift, probably the main purpose of bottom-hole choking is to accomplish an increase in the velocity of this- rising column, particularly in the lower portion of the tubing string. This it does first, by expansion of the free gas accompanying the oil; next, by liberation and expansion of some of the occluded gas normally carried in the oil to the surface; and lastly, by atomization, which results in a more intimate and uniform mixture of the oil and gas. It is apparent, then, that if this velocity, particularly in the lower portion of the flow string, at a given rate of production, is inefficiently low, owing either to an insufficient supply of gas or to excessive surface choking, and slippage takes place, bottom-hole choking should bring about an increased velocity of the gas and hence an increased lifting capacity. But if the velocity of the column of gas at this same rate of production through a surface choke alone is at or above a velocity necessary to lift the oil efficiently, increasing the velocity by bottom-hole choking would probably serve no useful purpose, other than to steady the flow by the better mixture of oil and gas and to lower delivery pressures.

Jan 1, 1932