Search Documents

By David A. Milligan

This paper outlines the research and development of a process to treat flotation tailings from the Darwin mill in lnyo County, California. A flowsheet was developed incorporating an agglomerated heap leach process using sodium cyanide to extract the silver values. Agglomeration was the key to developing this resource as the mill tailings averaged only 13% plus 100 mesh. Percolation through the heap would have been impossible without agglomeration to improve the permeability. The various tests that went into this research program are described with particular emphasis on the agglomeration techniques developed at the Anaconda Minerals Research Center. Start up and operation are discussed.

Jan 1, 1984

By F. H. Turan, F. W. Jessen

The gel strength and viscosity of two different suspensions of fractionated montmorillonite clay were measured by using a Stormer viscosimeter and Farm V-G meter. The amount of sodium poly-phosphate (sodium bexametaphosphate, sodium tetraphosphate and sodium acid pyrophosphate) adsorbed by the clay particles was determined. A relationship seems to exist between the amount of polyphosphate adsorbed and the nature of the surface, edge or plate, assumed to be the principal sites for selective adsorption. Reduction in viscosity and gel strength was found to be directly related to the adsorption. Both chemical bonding and physical adsorption seem involved in defloccula-tion Some indication of the axial ratios of particles of .l- to .04-micron average size is possible though study of the adsorption mechanism. INTRODUCTION AND PURPOSE A knowledge of surface areas of clay particles in a suspension and a precise determination of phosphate adsorption should provide a basis for a better understanding of reduction in viscosity and gel strength caused by molecularly dehydrated phosphates. The purpose of this investigation was to study the adsorption of sodium polyphosphates on suspensions of fractionated sodium montmorillonite. Although there is considerable uncertainty regarding details of the structure of montmorillonite, a generally accepted one is that suggested by Hofmann, Endell and wi1m.l The structure shown in Fig. 1 is an idealized one, and Marshall2 has postulated that it is possible for several isomorphous replacements to occur. Thus, aluminum may replace silicon, in which case an exchangeable cation would go along with the aluminum to neutralize what would otherwise be a net negative charge on the structure. There is disagreement among various investigators as to the particle size and shape of montmorillonite clays. Marshall2 reported the following results for the mean lateral dimensions of a Putnam clay (montmorillonite)— 3,730 A° for particles having average diameters ranging from 500 to 1,000 A, and 750 A° for those with an average diameter less than 200 A. The latter particles were estimated at 50A°in thickness, which would correspond to a stack of five unit cell layers. On the other hand, Shaw3 has interpreted micrographs as indicating that particles of montmorillonite ire readilv broken down to the individual cell layers by dispersion in water. Brindley4 and Merings indicate the ultimate particles to be of the order of 300 A° in mean lateral dimension. Van Olphen6 suggested the thickness of particles at four to five unit cell layers. It was suggested also that this number tends to become smaller with increasing dilution. Recently, Kahn and Lewis7 determined the size of sodium montmorillonite particles in aqueous suspension from electro-optical bi-refringence decay curves. The

By Alan K. Burton

The number of trucks required to perform a certain task is a function of the productive capability of one independent truck and the total tonnage required. Hourly productive capability of one truck is the product of trips, or cycles, per operating hour and effective payload. One cycle is made up of load, dump, and travel time, the sum of which comprises theoretical cycle time. This time is then derated by a productivity factor, giving an average effective cycle time which is used to calculate the number of cycles per hour. Rated payload is the truck's designed tonnage, while effective payload is the average amount that is actually carried. Manufacturers, particularly of the larger trucks, produce various body sizes designed to carry materials of different densities. However, it is not always possible to carry the rated payload because the material might be lighter than expected, a body of the required size cannot be produced, or because of spillage on particularly steep grades.

Jan 12, 1975

By S. J. Swainson

PHOSPHATE ROCK is a low- priced commodity. This fact has influenced the choice of mining and beneficiating methods to a greater degree, perhaps, than in most other low-grade mining operations. The fact that many yards of everburden and matrix must be stripped and mined per ton of salable "rock" produced and sold has necessitated he development of relatively simple btneficiating plants having high capacity and low capital and operating costs. The law of diminishing returns must always be reckoned with in phosphate mining and washing, and often recovery must be sacrificed in favor of costs in order to achieve the highest over-all economic efficiency. The phosphate-bearing formation, known as "matrix," is composed of (1) phosphate pebbles, which are somewhat rounded in shape and which vary in size from 1-in, to micron sizes, (2) rounded quartz grains usually smaller than 10 mesh, and (3) clay, of varying "stiffness," which is the binder of the matrix. The phosphate pebbles vary in hardness. Their color, which varies from white to black, is not a reliable indicator of the Bone Phosphate of Lime (B.P.L.) content of the

Jan 1, 1944

By Ralph H. Sweetser

OF SPECIAL importance in the design and construction of an iron blast-furnace plant are tile raw materials to be employed. Obviously the iron must come from some ore of that metal, but the many kinds available lead to important differences in plant arrangement, and in the design of furnaces and accessory equipment. For instance, the bulk of the gangue in the ore is subject to wide variation as is that of the ash in the fuel. A gradual increase in the bulk of raw material necessary to produce a ton of pig iron has been noted, but this has been more than offset, so far as costs of operation are concerned, by improvements in the machinery used for handling large quantities of ore. coal limestone, and slag. The mechanization of coal and iron-ore mining. the building of big ore boats and limestone carriers, of ore docks for fast loading and unloading, and the general use of heavy railroad equipment have all contributed to greatly reducing the number of man- hours required to mine, transport, and manufacture the raw materials into a ton of pig iron. This looks like a big saving and it is. If it were not for these big labor saving machines it would be impossible to produce the tonnage of iron and steel that is made each year in this country. On the other hand, the total capital investment necessary to bring down the man-hours per ton of pig iron to a 2.3 hours average at the blast furnace and to a total of only 12 man-hours from ore to metal (see Table 1) is so great that even the present high price of pig iron is probably not far above the true cost of manufacture when all the fixed charges are properly included.

Jan 1, 1939

By T. L. Loucks, E. T. Guerrero

Pressure drop characteristics in a system composed of two adjacent concentric regions of different permeability were studied. The differential equations for continuity of mass flow in the two regions were solved using the Laplace transformation and the necessary boundary conditions to give the pressure distribution in the composite reservoir, the resulting equation for pressure drop at the inner boundary was evaluated for a variety of composite reservoirs and compared with the results for a uniform reservoir. From this study it was found that under certain conditions the permeability in both zones, as well as the size of the inner zone, can be determined from the pressure drop curve. INTRODUCTION The theory for the pressure distribution and pressure build-up behavior of a well producing a single, slightly compressible fluid from infinite and finite homogeneous reservoirs was presented by Hornerl and Miller, Dyes and Hutchinson.2 Extensions on this original work to provide improved and extended interpretations and better agreement between theory and observed results have been made by Matthews, et a1,3 van Everdingen,4 Gladfelter, et al5 Stegemeierand Matthews,6 Hurst and Guerrero,7 and Perrine.8 More recently Lefkovits, et al,9 studied pressure build-up behavior in bounded reservoirs composed of stratified layers. Houpeurtl0 has suggested various approaches to the general problem of variable permeability and porosity but presented no analytic solutions for particular permeability variations. Albert, Jaisson and Marionll studied the finite composite reservoir and presented numerical solutions to the unsteady-state case and an analytical solution valid only for large times. They also studied the so-called pseudo-steady state for several examples of radial permeability variations. Very similar examples have been treated in the unsteady state with application to pressure build-up by Loucks in an unpublished manuscript. More recently Hurst12 has presented the complete point-sink solution (valid for all times) for the infinite composite reservoir. He applied these solutions to interference between oil fields along with an even more elegant application of his explicit solution to the material-balance equation including water influx. Mortada 13 approaches the same application by avoiding the point-source limitation but gives the solution for the aquifer region which is valid only for large times. Hopkinson, Natanson and Temple14 have treated both the finite and infinite composite reservoir obtaining the pressure distribution for the inner zone valid for large times. This paper presents a theoretical study of the pressure distribution in an infinite composite reservoir composed of two adjacent concentric regions of different permeability. The object was to determine the manner in which pressure drop at the inner boundary of a composite reservoir depends upon time, the permeability of each zone and the size of the inner zone. Expressions for the pressure distribution in both zones are developed which take into account the radius of the sink and are valid for small times as well as large times. It was felt that an understanding of the pressure drop behavior in various composite reservoirs would be of assistance in the interpretation of some pressure build-up curves which do not behave according to the theory derived for uniform systems. Often the region surrounding the wellbore is either more permeable or less permeable than the reservoir because of the various drilling and completion practices. The effects of reduced permeability due to drilling-fluid invasion and of increased permeability due to fracturing or acidizing need to be more carefully defined. Therefore, an equation for the pressure drop in a composite reservoir was developed, and the effects of both the permeability in each zone and the size of the inner zone were studied. STATEMENT AND SOLUTION OF PROBLEM BOUNDARY CONDITIONS AND ASSUMPTIONS The physical system studied was a composite

By Alfred H. Bell, George V. Cohee

Illinois produced 146,788,000 bbl. of oil in 1940, or nearly 11.0 per cent of the total for the United States, and ranked fourth among the oil-producing states. Its production was only slightly less than that of Oklahoma, which produced 11.5 per cent of the national total. Illinois' production in 1940 represents an increase of 55 per cent over the previous year, when it amounted to 94,912,000 barrels. The development of the Devonian limestone in the Salem and Centralia fields is largely responsible for the increase in production during 1940 Production from the Devonian limestone in these two fields was estimated to be 36,698,000 bbl., or 25 per cent of the state's total production (Table I). The increase in production during June, when the state's daily average production attained a peak of 518,200 bbl. for the week ending June 29, was due to the Devonian production at Centralia (Fig. I). The initial production of the best Devonian wells in the Centralia field was as high as 12,000 bbl. in 24 hr. Daily average production in IIIinois for 1940 was 400,000 bbl. of oil, but actually daily production fluctuated widely during the year. At the beginning of 1940 daily production was approximately 330,000 bbl. During the first hali of the year it in-creased irregularly to the peak in June mentioned above and as the prolific Devonian producing areas were drilled up, the state's daily production declined rapidly during July and continued to decline, although more slowly, until the end of the year, when the daily production was approximately 325,000 bbl. The daily average production per well in the new fields at the end of the year was approximately 40 bbl. (Fig. I). Oil from the Devonian was also produced in the Bartelso field, Clinton County, the Sandoval field, Marion County, and the Irvington field, Washington County, bringing the estimated total production from the Devonian limestone to about 26 per cent of the state's total production, The remainder was obtained largely from the Mississippian system. About 2 per cent of the total was from Pennsylvanian and Ordovician strata. The decline in the Devonian limestone production has been so rapid that the 1941 output from this system will probably be only a small fraction of that of 1940 unless large new reserves are discovered. The "Trenton" (Ordovician) limestone has been tested in two wells in the Centralia field and both were small oil producers at a depth of about 4000 it. The "Trenton" also was found productive in the Salem field at a depth of 4500 ft. (Table 5). The initial production of the discovery well, which was completed shortly after the end of the year, was 130 bbl. on pump. Other wells drilled early in 1941 had initial productions averaging 172 barrels. The outlook for 1941 is for a continuation of drilling activity in Illinois, but at a declining rate (Fig. I, upper curve). The most active area at the end of 1940 was in the deep basin area in Wabash, Edwards, White, and Hamilton Counties.

Jan 1, 1941

By Alfred H. Bell, George V. Cohee

Illinois produced 146,788,000 bbl. of oil in 1940, or nearly 11.0 per cent of the total for the United States, and ranked fourth among the oil-producing states. Its production was only slightly less than that of Oklahoma, which produced 11.5 per cent of the national total. Illinois' production in 1940 represents an increase of 55 per cent over the previous year, when it amounted to 94,912,000 barrels. The development of the Devonian limestone in the Salem and Centralia fields is largely responsible for the increase in production during 1940 Production from the Devonian limestone in these two fields was estimated to be 36,698,000 bbl., or 25 per cent of the state's total production (Table I). The increase in production during June, when the state's daily average production attained a peak of 518,200 bbl. for the week ending June 29, was due to the Devonian production at Centralia (Fig. I). The initial production of the best Devonian wells in the Centralia field was as high as 12,000 bbl. in 24 hr. Daily average production in IIIinois for 1940 was 400,000 bbl. of oil, but actually daily production fluctuated widely during the year. At the beginning of 1940 daily production was approximately 330,000 bbl. During the first hali of the year it in-creased irregularly to the peak in June mentioned above and as the prolific Devonian producing areas were drilled up, the state's daily production declined rapidly during July and continued to decline, although more slowly, until the end of the year, when the daily production was approximately 325,000 bbl. The daily average production per well in the new fields at the end of the year was approximately 40 bbl. (Fig. I). Oil from the Devonian was also produced in the Bartelso field, Clinton County, the Sandoval field, Marion County, and the Irvington field, Washington County, bringing the estimated total production from the Devonian limestone to about 26 per cent of the state's total production, The remainder was obtained largely from the Mississippian system. About 2 per cent of the total was from Pennsylvanian and Ordovician strata. The decline in the Devonian limestone production has been so rapid that the 1941 output from this system will probably be only a small fraction of that of 1940 unless large new reserves are discovered. The "Trenton" (Ordovician) limestone has been tested in two wells in the Centralia field and both were small oil producers at a depth of about 4000 it. The "Trenton" also was found productive in the Salem field at a depth of 4500 ft. (Table 5). The initial production of the discovery well, which was completed shortly after the end of the year, was 130 bbl. on pump. Other wells drilled early in 1941 had initial productions averaging 172 barrels. The outlook for 1941 is for a continuation of drilling activity in Illinois, but at a declining rate (Fig. I, upper curve). The most active area at the end of 1940 was in the deep basin area in Wabash, Edwards, White, and Hamilton Counties.

Jan 1, 1941

By H. J. Rose

Graphic methods have long been used to advantage in dealing with diverse phases of fuel technology and research. Not only are graphs convenient for presenting data and making calculations, but they are invaluable for deriving generalizations from a mass of data. This is particularly true when relationships are obscure and numerical correlation is poor. This paper describes a new form of graph, the Multibasic Coal Chart, which has been developed to facilitate the study and comparison of coals of all ranks from peat to anthracite on any moisture and purity basis. This type of chart is of unique value for coal classification purposes, since it permits a direct visual comparison of the results obtained when coals are classified by the various systems which have been proposed. Coals are highly variable in character as a result of wide differenees in original vegetal ingredients, degree of metamorphism, and nature and amount of associated impurities. For nearly 100 years, attempts have been made to devise a satisfactory method of classification, and many tables, formulas, ratios and graphs have been suggested. Many of the suggested systems possess considerable merit and have found a limited use, thus promoting a better understanding of coal. However, objections have been raised against each system, and none has received general adoption. When the various systems of classification are compared, it is found that there is an apparently almost hopeless confusion due to: 1. Serious lack of agreement as to the proper moisture and purity basis on which to classify coal. More than ten different bases have been proposed, each of which requires complete recalculat.ion of the analysis data used. 2. Lack of agreement as to what chemical and physical properties are most important and best to use for classification purposes. There is too little knowledge of the degree to which these properties can be correlated.

Jan 1, 1930

By Carlos E. Roggero

The influence of high temperatures on the zinc roasting practice has been investigated by full-scale tests in fluid bed reactors operating at temperatures from 950° to 1150°C. It was definitely shown that, throughout the range, an increase in tem perature resulted in a 2 to 3 pct increase in zinc solubility because of decreased content of zinc fer-rite and lowered sulfide sulfur. The former is attributed to thermal decomposition of ZnFe,O,, and the latter to increased oxidation rates, ad longer retention times. Data on the gveatly increased volatilization of lead, cadmium, and silver above 1000°C, are presented. A considerable fraction of the iron present in the feed was also transferred at high temperatures from the coarse roaster discharge to the flue dusts. AS part of its metallurgical complex1-3 situated in a 12,000 it Andean valley at La Oroya, Peru, Cerro de Pasco Corp. (a wholly owned subsidiary of Cerro carp.) operates a 150 short ton per day electrolytic zinc refinery. Electrolysis is carried out at a cathode current density of 65 amp per sq ft with an electrolyte content of 55 g per liter of Zn and 150 g per liter of su lf uric acid. Due to the high iron content of the marmatitic concentrate used, a large fraction—about 15 pct—of the zinc reports in the leach residues. To minimize such losses, efforts have been exerted toward improving calcine solubility. One method, as noted in the literatre,, is to retard zinc ferrite formation by decreasing the roasting temperature. Unfortunately, such a procedure tends either to reduce the roaster throughput or increase the sulfide sulfur in the calcine. Consequently, this approach was discarded in favor of experimental work in the opposite direction, i.e., high temperature roasting. Full- scale tests were promising and resulted in the granting of a patent to Cerro de Pasco carp.' After a brief account of plant equipment and operating procedure, this paper describes the tests made and attempts to assess the results obtained. GENERAL PLANT LAYOUT AND OPERATION The Roasting Plant, see Fig. 1, comprises an agglomerating plant feeding three fluid bed roasters with a combined capacity of 10,000 tons per month. The Peruvian patent rights on this process were purchased from the New Jersey Zinc Co. The concentrate, assaying: is pelletized to a -3 +14 mesh product and fed to the fluid bed roasters. The roaster exhaust gases pass through a waste heat boiler, cyclones, a fan, and an electrostatic precipitator. Approximately half of the dust collected in the cyclones returns to the pellet-izing plant as one of the binding ingredients, the remainder joins the cooled bed discharge ('overflow') and is conveyed to the grinding plant. The -35 mesh product obtained, together with the dust collected in the electrostatic precipitator constitute the feed to the leaching plant. Batch leaches are made in vessels with mechanical and air agitation, the residues are separated and washed in Burt Filters, and pumped to storage ponds. THE FLUID BED ROASTERS Two reactors are as shown in Fig. 2, and the third,' of about the same configuration, is approximately 40 pct smaller. The total grate and freeboard (just below the gas outlet) areas measure 170 and 426 sq ft respectively. The feed, continuously weighed and controlled by Merrick Weighto-meters fitted with variable speed motors, enters the reactors at the top of the expanded bed level. The coarse calcine overflows through the opposite end by

Jan 1, 1963

By C. G. Rhodes

A technique for producing etch pits in uranium monocarbide has been developed. The pits, which are assumed to be associated with dislocations, appear individually and as arrays delineating sub-boundaries, as seen in Fig. 1. The samples used were single crystals prepared by the technique described by Nadler.* Uranium

Jan 1, 1963

By J. D. A. Morrow

This discussion relates to the distribution of coal under the di , of the U. S. Fuel Administration beginning Apr. 1, 1918. At t' L a definite method of controlling and directing distribution was put int effect. Prior thereto, although some of the machinery utilized was in operation, especially in the few weeks immediately preceding' Apr. 1, distribution had not been effectively and comprehensively organized. The writer was called to the Fuel Administration by Dr. Garfield about the first of February, 1918, to assume general direction of the distribution of coal for the Fuel Administration, to develop the general plans, and to obtain practical men to assist in this work and in carrying through the program finally devised. A study of the situation and conferences with the Fuel Administrator and leading men in the business made it plain that it would be necessary to begin at the bottom, measure the undertaking, develop plans to meet the need thus shown, and build an organization to effect the distribution required. This work had to be done under war pressure in the midst of a bad coal shortage. The successful performance of such a task is always primarily a matter of putting competent men in the right places and giving them the power and opportunity to function properly together. In the Distribution Division of the U. S. Fuel Administration, the men who were chiefly responsible for whipping plans into practical form and then for carrying out these plans were A. W. Calloway, of Baltimore, President of the Davis Coal & Coke Co., who served as the Director of Bituminous Coal Distribution; S. Lovell Yerkes, of Birmingham, Alabama, Secretary of the Grider Coal Sales Agency, who assumed general charge of distribution while the new plans and organization were being perfected and then became the Assistant Director of Bituminous Coal Distribution; Warren S. Blauvelt, of Detroit, who was Director of Coke Distri. bution; A. S. Learoyd of New York, Director of Anthracite Distribution, in connection with the Anthracite Committee, consisting of Joseph P. Dickson, President of Dickson & Eddy, Chairman; S. D. Warriner, President of the Lehigh Coal & Navigation Co., and W. H. Richards,

Jan 1, 1920

By C. R. Claus, G. A. Standish

Since March. 1945, the Magnolia Petroleum CO. has drilled 39 wells in Southwest Coastal Louisiana. All wells were drilled within a comparatively small radius, but the area provides a large variety of problems. The deepest well drilled was 13,518 ft, and the total depth averaged 10,977 ft. Throughout this period drilling mud control and types of mud handled were: (I) phosphate, (2) red lime (late conversion), (3) red lime starch (early conversion), (4) red lime starch oil emulsion, (5) precision controlled low alkalinity-low lime content. and (6) gel muds for completion purposes. Improvement has been obtained in effecting some or all of the following: (I) more rapid penetration, (2) reduction in drilling hazards, (3) better evaluation of cores and logs, and (4) better completions. The geological sequence of zones penetrated range from recent sediments at the grass roots through the Frio section. Anticipation of high-pressure zones and incompetent formations entails precision control of drilling mud weights, and the unconsolidated nature of the various zones requires constant attention to the filtrate, viscosity, and gel strength values. In the Chalkley field, particularly, this combination of problems exists, where the formation pressures and overburden weight density values are in very close proximity. Design of casing and drilling mud programs must be modified to fit each well. INTRODUCTION Field and research work on drilling fluids has made constant progress, enabling operators to prospect progressively deeper horizons. Numerous papers have been written on the theoretical aspects of drilling fluid devel- opment, but in the field engineers have found it difficult to evaluate the role of specific mud constitutents when dealing in terms of thousand barrel mud systems. For that reason field data is somewhat lagging in technical report writing. However, applications of new techniques in the field have usually paralleled, and in numerous instances preceded, research work. The information obtained by Magnolia Petroleum Co. in the course of drilling 39 wells within a comparatively small area in Southwest Coastal Louisiana provides an excellent opportunity of reviewing a specific example of drilling mud evolution. A large variety of problems has been coped with, the most important result being that every well was successfully drilled to its projected total depth. The discussion begins with the advent of deep drilling in this area in March, 1945, and is concluded with a resume of recent drilling operations in the Chalkley field. The primary purpose of this paper is to describe the evolution in types of drilling fluids as it occurred and its application in the solution of various drilling problems. All of this information and experience resulted in the successful drilling of the three wells in the Chalkley field, where a combination of the most sound techniques was necessary in carrying drilling operations to the projected total depths. Other operators along with service company engineers have contributed considerably through the interchange of ideas and information to this paper, but the data and conclusions which are contained are based on first-hand observation of Magnolia Petroleum Company's drilling operations. The 39 wells drilled by Magnolia Petroleum Co. average in depth 10,977 ft per well, while the maximum depth penetrated was 13,518 ft. The cost of drilling fluids have varied from $8,700 to $165,000, with the over-all drilling costs ranging from $74,000 to $543,000 per well. This wide variance illustrates the unpredictable nature of each well and the effects on over-all cost when high density muds are required to control

Jan 1, 1955

By Robert E. Ogilvie, Zvonimir Ban

Oxidation experiments were conducted above 600°C to investigate the oxidation products formed on the surface of MoSi2. Results are presented which indicate that minor iron impurities play a key role in the oxidation behavior of MoSi2 above 600 °C. Based on considerations of the crystal chemistry of the oxidation products, MoSi2 with rhenium and iron additions was found to be resistant to oxidation in the pesting temperature range. AS early as 1914, Honigschmidtl observed that some silicides of molybdenum exhibited high resistance to oxidation at elevated temperatures. This fact did not arouse much interest until 1950, when Kieffer and cerwenka2 examined this property in more detail. They found that Mo-Si alloys with approximately 70 pct Mo (by weight) could be heated to 1600°C in an oxidizing atmosphere without any significant damage. The surface was found to be protected by the formation of an extremely thin silica glass layer which had no tendency to spa11 during subsequent thermal cycling. In 1955, Fitzer3 discovered that even solid bodies made of MoSi2 completely oxidized within a relatively short time when exposed to the air in the temperature range from 300° to 600°C. To describe this phenomenon he proposed the name "molybdenum disilicide 'pest' ", clearly analogous to the previously observed "tin plague" ("tin pest") which, however, arises as the result of a phase transformation. Studies performed by Fitzer and, in particular, one published recently by Berkowitz, Blackburn, and Fel-ten,' comprise the most extensive research to date on the pest phenomenon in MoSi2, as far as the fundamen- tal mechanism of the process is concerned. The first of these studies revealed the existence of a crystalline phase which appeared at the surface at 750°C and dissolved in the glassy silica layer at 1150°C. The logical assumption was that this phase was some reaction product of MOO3 and SiO2. The formation of a reaction product of this type seemed probable since it had been mentioned by Glemser and Lutz6 in a paper describing their studies of molybdenum oxides; however, this assumption was later disproved.8 It is our belief that information concerning the exact nature of this crystalline phase may be important for a better understanding of both pesting and the protection mechanism. Therefore, since the only available general description of the pest phenomenon was that of Fitzer, it was decided to reproduce his experiments. These experiments established that, in addition to the "pest" and "nonpest" temperature range, an intermediate region exists between 600" and approximately 650°C. This region is characterized by the appearance of a variable amount of yellow to orange colored crystals. The electron-beam microanalyzer was used to qualitatively determine their composition. Iron and molybdenum were found to be major constituents. This result can be explained based on the following facts: 1) iron, according to literature data,* is the most common impurity in molybdenum powder, and its content can be as high as 0.25 pct; 2) technical silicon powder usually contains iron; 3) steel ball mills are often used for the crushing and grinding of MoSi2. In order to clarify the exact role of iron, it was deliberately added to a stoichiometric mixture of molybdenum and silicon. The observed results corroborated the previous experiment, proving that iron (probably as some silicide phase) concentrates along the grain boundaries. I) EXPERIMENTAL PROCEDURE A) Oxidation of MoSi2 with Iron Additions. 1) Specimen Preparation. Specimens were prepared by both

Jan 1, 1967

By Richard F. Hinds, F. O. Reudelhuber

Application of the conventional depletion drive calculation methods to volatile oil reservoirs results in erroneous estimates of ultimate recovery. In view of the increasing number and importance of volatile oil reservoirs, a special technique has been developed which will result in more realistic predictions using laboratory data obtained from reservoir fluid studies of a specific type. The experimental data are designed to permit continuous material accounting and, therefrom, provide the hy-clrocarbon composition of both the flowing oil and gas phases. The resultant well-stream composition data are then used directly in surface recovery calculations utilizing equilibrium ratios. A step by step procedure, specifically designed for routine use by the practicing reservoir engineer, is presented in an appendix. An actual study performed on a deep Mid-Continent reservoir is used ay an il-lustrathe example. INTRODUCTION It has been a practice for many years to utilize the conventional ma- terial balance methods in conjunction with relative permeability concepts for the prediction of recovery from solution gas drive reservoirs.' Those who have performed such calculations recognize that compromises of several types are necessary in order to reduce the calculations to a reasonable degree of complexity. The most serious assumption involved results from the necessity of treating the produced oil and gas as separate fluids, independent of each other in their behavior. It is further assumed that the gas which is evolved in the reservoir as a result of pressure decline will not yield liquid upon the reduction of pressure and temperature resulting from production through surface equipment. Although these shortcomings have been recognized,' it has been difficult to attempt refinement of calculation procedures since the laboratory data available normally were not of the proper type or extent to permit such calculations. Three general procedures have been available for depletion drive calculations when laboratory fluid data are of the conventional type. Differential Procedure The most simple, and most widely used, method requires use of the formation volume factor and gas sol- ubility data obtained from a differential liberation performed at reservoir temperature. This procedure ignores the differences existing between the fluid behavior in the reservoir and its behavior as it is produced through surface separation equipment. The errors introduced are not serious when dealing with very low volatility fluids and this method may be utilized if the laboratory data indicate only slight differences between the differential data and the flash data obtained from separator tests. Modified Differential Procedure This method was developed when it became apparent that medium volatility fluids evidenced a wide difference between the flash and differential data. The differential data are adjusted by changing from a residual oil basis to a stock tank oil basis. All that is required is multiplication of the differential data by the ratio of residual oil to stock tank oil relative volumes existing for the original reservoir fluid at the determined saturation pressure. This procedure generally results in increased calculated ul-timate recovery; however, such results should be viewed critically. Upon examination it may become apparent that the results are influenced by errors in reservoir liquid

Jan 1, 1958

By J. Eric Belford

The Kidd Creek orebody is a massive base metal sulphide deposit with surface dimensions of 168 m by 670 m. The steeply dipping ore- body has been evaluated to a depth of 1 524 m. To date, the mining of the orebody has been divided into three stages. The first stage of mining was an open pit operation which supplied ore from 1966 until 1977 when a depth of 219 m was reached at the widest or north end of the orebody. The second stage of mining, called No.1 Mine, was the development of an underground mine to replace the pit and recover the ore from the floor of the pit to a depth of 792 m. Development of the underground mine started in 1969. Full production of 273 000 tonnes per month was attained in 1977. The third stage of mining called No.2 Mine, was initiated to accommodate a production expansion and included the development of a second underground mining operation to recover the ore from the bottom of No.1 Mine, i.e. the 2600 level; to a depth as yet undetermined but most likely the 4600 foot level. Development of the No.2 Mine began in 1974. Full production of 91 000 tonnes per month will be achieved in 1982. The choice of the 2800 level as the partition between the two underground mines was based on the following factors: The 2600 level is the lowest level which can conveniently be mined through the No.1 Mine crusher on the 2800 level. Development and trial stoping methods for mining at depth could be evaluated in the 2600 to 2800 block utilizing the existing hoisting facilities of No.1 Mine. Early development of the ore in the 2600 to 2800 block would provide additional mill feed sooner than could be achieved by developing from No.2 Shaft. The underground mining plan then is to mine from the pit floor down to the 2600 foot level and at the same time mine from the 2800 level down to at least the 4600 foot level. PLANNING The Kidd Creek operations are designed to follow a logical mining sequence. The grade of ore supplied to the concentrator is the result of following the mining plan. The philosophy of mining has been to mine downward in horizontal slices. In the case of No.1 Mine the slices are 122 m thick while in No.2 Mine the slices will be 183 m thick. The point of this approach is to mine the pillars immediately after creating them rather than allowing them to stand, deteriorate and generate uncontrollable situations. Two types of ore are handled separately to optimize recoverable values in concentrates. The 'A' type ore is a copper zinc ore with some silver and little lead. The 'C' type ore is a zinc silver ore with some lead and copper

Jan 1, 1981

By James Norman

DIATOMACEOUS earth occurs in deposits widely distributed throughout the nation. The chief producing areas are in the Western States, where many high-grade deposits are known. Eastern deposits of diatomite are unsatisfactory for many purposes either because of impurity or because of the extremely fine particle size. Eastern users of diatomite, on the whole, must pay for transportation of the material from the west coast. The freight rate is necessarily high because of the great bulk of the diatomite. A satisfactory process of purifying the diatomaceous earths of Maryland and Virginia, which are unsuited for wide use only because of impurities, should be of value to eastern users. In the past, benefication of diatomite by wet processes has been limited to classification or sedimentation for the removal of sand from diatoms. Calcination with salt is used to produce a white diatomite when iron is present in the impurities, and small amounts of clay are rendered inactive in the process. No treatment has been developed whereby a large proportion of clay can be removed from a low-grade diatomaceous earth to give a diatomite of very high purity. In August 1937 the Federal Bureau of Mines, in cooperation with Dr. R. C. Williams, of Baltimore, undertook the problem of purifying low-grade Maryland diatomite by froth flotation. Work was done at the Eastern Experiment Station, College Park. Unless otherwise stated, the crude diatomite used was from the Patuxent River deposits near Dunkirk. This material, consisting of roughly one-third each of clay, quartz sand and diatoms, was representative of the usual low-grade marine diatomite found in the Coastal Plain Miocene beds of Maryland and Virginia and sporadically in other Atlantic coast states. As received, it contained 50 to 60 per cent moisture and probably had been wet since its formation.

Jan 1, 1940

By R. W. Diamond

THREE mills are now operated by the Consolidated Mining & Smelting Co. of Canada, Ltd.: (1) The Sullivan Concentrator, Chapman Camp, B. C. (near Kimberley, B. C.), (2) the, St. Eugene Concentrator, Moyie, B. C., and (3) the. Tadanac (Customs) Concentrator,Trail, B. C. Differential flotation is the only concentration method employed in all three plants. Tables are used for pilot work only. Values in all ores treated are as minerals of some or all of the metals -lead, zinc, gold or silver. Occasional customs ores contain small amounts of copper. Sulfide iron content of ores treated varies from a FIG. 1.-THE SULLIVAN CONCENTRATOR, CHAPMAN CAMP, B. C. (NEAR KIMBERLEY, B. C.). low figure in some ores to 38 per cent. iron in Sullivan ore. Gangue minerals vary considerably. A few customs ores are somewhat oxidized and as a result present difficulties. Flotation equipment and control are similar in the three mills, and the flow sheets at the St. Eugene and Tadanac mills, while much simpler, are modeled after that of the Sullivan Concentrator. In this paper I will not detail treatment nor equipment in any of our plants but will describe special features in, or in connection with, all of them. I will then deal with flotation reagents, describing our use of each of them, particularly where differing from general practice. I will conclude with comments on special subjects related to differential-flotation.

Jan 1, 1927

By Shiou-Chuan Sun

THE presence of an excessive amount of tough froth in the flotation of minerals, particularly coals, may create trouble in dewatering, filtering, and handling. Froth is also a nuisance in many chemical industries.' This paper presents a study on the destruction of extremely tough froths with intense high-frequency sound. The data indicate that sound waves can be employed for continuous atandsoundwavescan instantaneous defrothing. A powerful high-frequency siren was used in obtaining the data. Also tested was an ultrasonorator of the crystal type with a frequency range of 400, 700, 1000, and 1500 kc per sec and a maximum power output from its amplifier of 198 w. The results, not presented, indicate that as now designed this machine is not suitable for defrothing. Although the sound generators of the magnetostriction type2,3 and of the electromagnetic type'.' were not available, it is beelectromagneticlieved they are capable of producing the required sound intensity for defrothing. The use of ultrasonics for defrothing was suggested by Ross and McBain1 in 1944. Ramsey8 reported in 1948 that E. H. Rose mentioned a supersonic device that broke down flotation froth but with low capacity. The writer has not been able to find any published literature containing practical experiments. Theoretical Considerations The mechanism of defrothing by sound is attributed to the periodically collapsing force of the propagated sound waves and the induced resonant vibration of the bubbles. The collapse of froth is further facilitated by the sonic wind and the heat of the siren. Sound waves can exert a radiation pressure'," against any obstacle upon which they impinge. When a froth surface is subjected to the periodic puncturing of sound waves, the bubbles are broken. According to Rayleigh9 and Bergmann,12 the radiation pressure of sound, P, in dynes per sq cm is given as: P = 1/2 (r+1)i/v where r is the ratio of the specific heats of the medium through which sound is traveling and is equal to 1 on the basis of Boyle's law; i is the sound intensity in ergs per sec per sq cm, and v is the sound velocity in cm per sec. In this case, the accuracy of the formula is only approximate, because a perfect reflection can hardly result from a column of froth. In addition to the radiation pressure, the propagated sound waves cause the bubbles of the froth to have a resonant vibration.'" he vibratory motion of the bubbles causes collision and coalescence, thereby weakening if not breaking the bubble walls. Sonic wind and heat were also generated." The sonic wind can exert pressure on the froth surface, and the heat can evaporate the moisture content of the bubble walls as well as expand the enclosed air. Apparatus The defrothing apparatus, shown in Figs. 1 and 2, consists of a powerful high-frequency siren, a glass or stainless steel beaker of 2-liter capacity with 12.4 cm diam and 17.1 cm height, and a metal reflector. The beaker was placed 2 in. above the top point of the siren. The metal reflector was adjusted to reflect and focus the generated sound waves into the central part of the beaker. Fig. 2 shows the crystal probe microphone used to measure the acoustic intensity and the mandler bacteriological filter employed to introduce compressed air into the beaker for frothing. The apparatus was enclosed in a soundproof cabinet equipped with a glass window. The siren, shown in Fig. 3, consists of a rotor that interrupts the flow of air through the orifices in a stator. The rotor, a 6-in. diam disk with 100 equally spaced slots, is driven by a 2/3 hp, Dumore W2 motor at 133 rps. The frequency of the siren can be varied from 3 to 34 kc. The maximum chamber pressure is about 2 atm, yielding acoustic outputs of approximately 2 kw at an efficiency of about 20 pct. The siren itself is relatively small and can be operated in any orientation. A detailed description of the siren has been given by Allen and Rudnick.11 Collapse of Froth To study the sequence of the collapse of froth, the glass beaker was partially filled with 920 cc water, 100 g of —150 mesh bituminous coal, 0.3 cc petroleum light oil, 0.2 cc pine oil and 1.54 cc Pyrene foam compound. This mineral pulp was agitated for 5 min and then aerated through a mandler filter until the empty space of the beaker, approximately 9 cm high, was filled completely with min-

Jan 1, 1952

By P. Somasundaran

Flotation of minerals has usually been discussed in terms of solid-liquid interfacial phenomena. This paper discusses the relative importance of phenomena such as collector adsorption at other interfaces formed between the bubble, liquid and solid. Adsorption of collector ions of various chain lengths at liquid-gas and solid-gas interfaces has been obtained. The data have been analyzed under conditions corresponding to those of flotation to show the significant role of collector adsorbed on the bubble surface in determining the bubble-mineral attachment required for flotation, and consequently to suggest consideration of this role in the development of better flotation conditions. Vacuum flotation of quartz with alkyl ammonium acetate reported in the foregoing paper1 showed that the collector chain length has an effect on flotation even at concentrations below those necessary for hemi-micelle association of the hydrocarbon chains at a solid-liquid interface. This chain length effect might be explained by the following arguments: Hydrocarbon chains find it energetically favorable to be in a medium of low dielectric constant. Considering the possibility of an iceberg structure at the solid-liquid interface, such a structure would produce a region of lower dielectric constant at the solid-liquid interface than in the liquid phase, because the dielectric constant of ice is 2 to 3,2 while that of water is 80. Depending on chain length, this difference will certainly cause even individual ions to adsorb in higher quantities at the solid-liquid interface. Another mechanism to consider is the possible formation of dimers, trimers, etc and chain length would influence this formation. But, above all, the chain length effect on flotation at concentrations of low adsorption at the solid-liquid interface could be due to the significant but often-neglected role of the collector adsorption at the bub- ble surface. Collector ions or molecules are adsorbed both at the solid-liquid interface and the liquid-gas interface. Below the concentration for hemi-micelle association at the Stern plane adjacent to the surface, the bulk of the collector ions adsorbed at the solid-liquid interface are in the diffuse part of the double layer. If such systems, where there is a gas bubble coming in contact with the solid surface, are to achieve some degree of electroneutrality, those collector ions would have to migrate from the diffuse part of the double layer to the region directly adjacent to the surface during the induction period when the bubble is making contact with the solid. The time necessary for this migration would contribute to the induction period required for creation of the solid-gas interface. It seems reasonable that the induction period could be reduced sufficiently for flotation to occur if these collector ions were carried to the surface by the bubble. In an attempt to ascertain whether or not the bubble could possibly have sufficient collector ions at its surface to meet the requirement mentioned above, the adsorption density of the collector ions at the liquid-air interface was determined. For this purpose, the surface tension of alkyl ammonium acetate solutions was determined as a function of concentration. Adsorption densities of the collector at the liquid-gas interface were calculated using the Gibbs adsorption equation: where y is the interfacial tension and ri and pi are the adsorption density and the chemical potential, respectively, of the chemical species, i. Using the convention that the adsorption density of water at the interface is zero, the following relationship is obtained for the liquid-gas interface where lg refers to liquid-gas interface and RA+ refers to the alkyl ammonium ions. For dilute solutions, rf^-wri^&rfwW [3] where C is the concentration of the collector ions in solution. l?:: can now be evaluated using Eq. 3 and surface tension measurements.

Jan 1, 1969