Search Documents

By Fred Leighton, Wilson Blake

The microseismic method of detecting instability and high-stress zones in underground mines was developed by the U.S. Bureau of Mines (USBM) in the early 1940's.l,2 For about 25 years this method has been used throughout the world by mining and construction companies in assessing the stability of underground and surface excavations. Rock noises are the release of small amounts of stored strain energy propagating outward from their source as a seismic wave that can be detected with special geophysical equipment. This release of strain energy is caused by a rock mass undergoing load changes resulting in small-scale displacement adjustments such as microcracking, shearing, sliding, and crushing of crystal grains, some even as small as the elastic displacements themselves. No detailed field studies of any of these mechanisms have been made, and knowledge about the origin of rock noises is relatively incomplete. Laboratory tests have shown that when rocks are stressed in a testing machine, the rock noise rate-the number of rock noises generated per unit of time increases with increasing applied stress.3 This increase is most pronounced as the ultimate strength of the rock is approached. The standard field procedure has been to monitor a rock structure at intervals and plot rock noise rates vs. time, thus gaining a semiquantitative estimate of the behavior and stability of the structure. The success of such monitoring, however, has depended almost entirely on the experience and knowledge of the operator, his interpretation of the data, and his equipment. Very little study has been devoted to the basic properties of the vibration record of a rock noise. USBM decided that the microseismic method was being used sufficiently by various mining and construction companies

Jan 1, 1970

By W. I. Duvall

A brief review of the resonant frequency and ultrasonic pulse methods for obtaining elastic constants of rock samples shows that the equations for an iso-tropic elastic solid commonly used to calculate Young's modulus, modulus of rigidity and Poisson's ratio can result in appreciable error if the rock is even slightly anisotropic. Consideration of the equations that relate bar velocities and free medium velocities to elastic constants for orthotropic, transversely isotropic and isotropic solids shows that a combination of the two methods can be used to determine average elastic constants for a single sample of rock. The determination of elastic constants in different directions requires a large number of tests on oriented samples. The use of both the resonant frequency and ultrasonic pulse methods is recommended so that the determination of both Young's modulus and modulus of rigidity is independent of the determination of Poisson's ratio. The dynamic elastic constants of rock can be determined in the laboratory from measurements on small samples which may be in the form of right circular cylinders (diamond drill core). Either the resonant frequency6 or ultrasonic pulse method1 can be used to determine the longitudinal and shear velocities in the same specimen. The resonant frequency method provides a measure of the longitudinal bar velocity, V,, and the torsional bar velocity Vt; whereas the ultrasonic pulse method provides a measure of the free medium longitudinal velocity, Vp, and the free medium shear velocity, V, . The elastic constants (Young's modulus E, modulus of rigidity G, and Poisson's ratio v) are calculated from the density of the specimen, p, and one of the pairs of velocities by means of equations from isotropic elastic theory. For the resonant frequency method the equations are: It should be noted that Eq. 5 is derived from Eq. 4 and 6 and the relation between the elastic constants for an isotropic solid as given by the first part of Eq. 3. The in situ determination of dynamic elastic constants is accomplished by generating a complex seismic pulse in the rock and measuring the arrival times for the longitudinal and shear phases of the pulse at two distant points.5 From these travel times and the distance of the travel path both Vp and Vs are determined. The density of the rock is determined from samples in the laboratory, and Eq. 4 to 6 are used to calculate the elastic constants. These three methods involve the assumption of isotropy and perfect elasticity, and require the use of the relation v = (E/2G) - 1, which holds only if the elastic constants are the same in at least two directions. The calculation of v by means of Eq. 3 introduces considerable error, as a 1% error in V, and V, results in a 20% error in v. If frequencies for samples with a length-to-diameter ratio greater than four and a length greater than 8 in. are measured carefully, the experimental error can be kept to 1%. However, it is not unreasonable to expect that the variation in Vb and Vt with direction may exceed 1%. Thus, for even a small percentage of anisotropy the use of Eq. 3 can result in considerable error in v. The calculation of v by Eq. 5 also involves some uncertainty as a 1% error in Vs and Vp can result in a 6% error in v. By means of the pulse method both

Jan 1, 1965

By Arthur B. Foote

Ore production from the property of the Miami Copper Co. began early in 1911. Until 1925 this ore came from the so-called high-grade orebodies, which contained a little over 2 per cent. copper. This ore was mined by the following methods: 1. Top slicing after mining the peaks by square setting, which produced 4,524,347 tons, including ore from square setting. 2. Shrinkage stoping with sublevel caving of the pillars, which produced 2,230,577 tons. 3. Undercut caving with hand tramming, which produced 15,427,672 tons. Estimating December tonnage, the total ore mined to the end of 1929 will amount to slightly more than 43,000,000 tons. The first method was described by E. G. Deane' and the second by D. B. Scott,' and the third, together with a general description of the mine, by J. H. Hensley, Jr.' The geology of the district has been worked out by Dr. F. L. Ransome.2 The author acknowledges also the assistance of R. W. Hughes, assistant mine superintendent, E. V. Graybeal, chief mine engineer, A. J. McDermid and S. R. Burdick, engineers of Miami Copper Co., Miami, Arizona. Factors Influencing Selection of Mining Methods The mining method described herein was selected primarily with a low mining cost in view and was developed to avoid as far as possible dilution of the already very low-grade ore. In 1924, with the exhaustion of the high-grade orebodies in sight, it was decided to develop the low-grade orebody, which at that time contained 36,000,000 tons of ore assaying 1.06 per cent. copper, and had an area of 50 acres with an average thickness of 206 ft. overlain by an average thickness of 320 ft. of barren capping.

Jan 1, 1930

By Donald L. Katz, Leslie J. Noaker

Experimental data are presented for hydrate formation conditions for mixtures of hydrogen sulfide and methane. Vapor-solid equilibrium constants for hydrogen sulfide are also presented. Equilibrium constants, defined here as the ratio of the mole fraction of hydrogen sulfide in the vapor phase (dry basis) to the mole fraction of hydrogen sulfide in the solid phase (dry basis), were calculated using the vapor-solid equilibrium constants for methane presented in an earlier paper. The conditions at which a natural gas will form gas hydrates with water may be computed from its composition, when hydrogen sulfide is present in addition to carbon dioxide and the paraffin hydrocarbons. INTRODUCTION Many gases are known to form solid hydrates in the presence of liquid water at temperatures above 32°F. This hydrate formation is of importance to the natural gas industry inasmuch as most of the constituents found in natural gases will form hydrates. The attention of the industry was called to hydrates by Hammer-schmidtl0 in 1934. A number of papers have been written giving the temperatures and pressures at which these hydrates will form3,4,5,6,7,8,9,10,13,14,15,18,19 and a bibliography on the subject has been compiled13. Deaton and Frost4,5,6,7,8 report work for various pure gases and for some natural gases. Katz and co-workers3,4,13,14,18,19 have reported data for various gases at high pressure. They developed a method of predicting conditions for hydrate formation from equilibrium constants3,19 and from gab gravity." The effects of anti-freeze agents on the formation of hydrogen sulfide hydrate were reported by Bond and Nelson.' The hydrogen sulfide-water system, including hydrate, has been the subject of recent investigation by Sage and co-workers." Mixtures of hydrates behave as solid solutions and an equilibrium exists between the vapor phase and the solid phase that appears to be comparable to the equilibrium between vapor and liquid phases.3,10 By means of the vapor-solid equilibrium constants which have been published for methane, ethane, propane, iso-butane, and carbon dioxidel6 it is possible to determine the temperature and pressure at which hydrates will form for a specific gas mixture when water is present. Hydrogen sulfide which is frequently found in natural gases has a very strong tendency to form hydrate and must enter the solid solution when present in a natural gas forming a hydrate. To determine the effect of hydrogen sulfide when computing the conditions for gas hydrate formation, it is necessary to have the equilibrium constant giving the ratio of the concentration of hydrogen sulfide in the gas phase to the concentration in the solid phase. This paper presents data on hydrate formation for mixtures of hydrogen sulfide and methane and presents the equilibrium constants which were calculated from these data. EXPERIMENTAL PROCEDURE The apparatus used to determine the conditions of hydrate formation for the methane-hydrogen sulfide system was similar to that employed by previous investigators.3,18,19 A charge gas cylinder was used to supply the hydrogen sulfide-methane mixtures, called the charge gas, and to supply the pressure up to 1.000 psia. This

Jan 1, 1955

By A. J. Williams

THE province of Saskatchewan, situated in the center of the Great Plains region of Canada, has, like most prairie areas, an essentially agricultural economy. Most of its population of about 860,000 is located in the southern half of the province in the farming and ranching areas. To the north of the prairie is a broad forested belt supporting a considerable timbering industry, and the northern one third of the province is glaciated pre-Cambrian rock formation. This latter area is relatively barren of vegetation, but the presence within it of a considerable variety of radioactive, noble and base metals, and industrial minerals has been shown by prospecting in recent years.' Glacial Geology The Keewatin ice sheet, considered to have accumulated in the country to the west of Hudson Bay in Pleistocene time, covered at its maximum advancement almost all of Saskatchewan and extended south of the international boundary. Only in the Cypress Hills in the southwest and around Wood Mountain in the south central portion of the province did the preglacial formations escape the action for this glacial period. The bedrock of the plains and forest areas therefore is overlain by moraines and modified glacial drift, which vary in thickness from a few feet to 400 or 500 ft.' Glacial action in the pre-Cambrian area of the province was largely erosional, most of the more recent formations and some of the pre-Cambrian rock being transported out of the area to the south and west. It has been estimated that about 13 pct of this area is composed of lakes and rivers not too adaptable to rail or water transportation, so that until the use of aviation for exploration purposes became general, development of the area was slow. To the south, the heavy mantle of glacial drift has to some extent deterred the discovery of industrial minerals in the bedrock underlying the forest and prairie regions3 At the same time, this drift contains numerous deposits of those most elementary and necessary industrial minerals, sand and gravel. Sedimentary Basin The major feature of the sedimentary deposits underlying the plains regions is the basinal structure known as the Moose Jaw syncline, which runs from the southeast corner of the province in a northwesterly direction. To the west of this syncline the formations curve upward, then have been faulted and further upthrust to appear at the surface in the foothills of the Rockies in Alberta; to the east and north they curve upward into Manitoba and northern Saskatchewan, but the surface contacts are covered mostly with glacial drift.238 The axis of the syncline dips to the southeast, so that there is also an upward trend of the formations along the axis to the northwest. In illustration of the regional structure underlying the province, the pre-Cambrian basement has been logged in drillholes at the following depths in several locations: Ogema (south central), 9390 ft; Gronlid (northeast), 2599 ft; Vera (northwest), 4422 ft; Big River (north northwest), 2348 ft. Fig. 1 indicates the general surface geology of the province, ignoring such glacial overburden as may overlie many of the bedrock formations. Also indicated is the approximate location of the axis of the Moose Jaw syncline.' Industrial Minerals Clays: The province is fortunate in possessing a widespread distribution of clays of ceramic value, ranging from those used for heavy structural products to the high grade pottery and china clays. Shales suitable for brick and tile production are found in the Upper Cretaceous and Tertiary formations across the south of the province where the glacial drift is thin or nonexistent. Many deposits of glacial lake clays suitable for such wares are found scattered over the rest of the province south of the pre-Cambrian area. The Whitemud formation of the Upper Cretaceous is a narrow sedimentary band of secondary clays found intermittently at points across the south of the province where glacial action did not disturb or remove them.' In the southwest corner of the province, around Eastend in the Frenchman River valley, the refractory clays of this formation are contaminated somewhat with iron compounds or other alteration products of basaltic rocks. This eliminates the use of those clays in true whitewares, as they fire to creamy buff shades at the lower temperatures and to a blue-specked grey at cone 8 to 12, (2280°F to 2390°F), the range commonly used in firing whiteware. However, for use in the production of colored artware, caneware, stoneware or crockery, and sewerpipe, this type of clay makes an excellent body that requires little or no addition of flint, feldspar, or other fluxing materials such as are required in the higher class of ware.' It is not a grade of clay that can be shipped great distances to the manufacturing centers, but a market for considerable tonnages has developed at nearby Medicine Hat, where cheap natural gas is available for the firing of the ware. Farther east in the south central portion of the province, the clays of the Whitemud formation are generally more refractory and white burning. The formation is divided into three zones, consisting of white clays, brown shale, and white sandy clays.

Jan 1, 1953

By Ernest A. Hersam

IN every commercial establishment,' it is customary and necessary to take inventory, periodically, and to account for profits and detect losses, to achieve productiveness and enhance efficiency. So, too, in the ordered life of every individual, there is the need of periodic introspection. The exercise of the Sabbath for rational thought, the utilization of pause, or rest, from the technique of daily occupation, orient the efforts. These are the constructive opportunities by which we grow always better than we were. Thus, also, there' is need of a periodic analysis of the organizations to which we belong and toward which we con- tribute. So we find' reason for the fitness of our loyalty. There seems to be no half-ground for the engineer. Whatever presumes to bear his name demands either the crushing pressure of his heel or the supporting pressure of his hand.

Jan 1, 1929

By Paul R. Cook

The ore deposit of the Buckhorn Mines Co., Buckhorn, Nev., is peculiar in being a shallow kaolinized mass of material with basalt walls, and having apparently no direct connection with any of the usual gold-bearing rocks. The average ore contains 16 per cent. water of hydration, and the cyaniding of this hydrous clayey material offered unusual difficulties as compared with an average Nevada quartz ore. The orebody was thoroughly developed; then the mill was built according to the latest cyanide practice, with such changes as were thought to be demanded by the peculiar nature of this ore. Upon starting the mill, the ore proved more difficult to handle than had been anticipated. It is hoped that an account of how these difficulties were met may prove of interest to anyone having a clayey ore to handle and to the profession in general. Geology The Buckhorn orebody lies along a north and south fault plane of perhaps 1,000 ft. dislocation, that can be traced for miles; but the only other known mineralization consists of similar ore in the Murphy mine, a mile farther north. The east or hanging wall is hard and smooth, being a typical fault plane. The best ore is along this wall, gradually grading down toward the west until at 30 to 60 ft. it is too low-grade to mine. The country rock on the west consists of alternating layers of hard and soft basalt and basalt scoria, pitching toward the mine. One of these basalt layers on the hillside a little above the mine is marked, for 3 or 4 miles in length, by a line of springs which seep out along it. Perhaps the meeting of the surface drainage, passing down these basalt layers, with the fault-plane solutions explains the formation of the Buckhorn orebody.

Jan 1, 1917

By E. F. Bailey, W. J. Harris

THE temperature of the ferrite to austenite re-action is established frequently by continuous heating experiments. However, equilibrium studies of this reaction have demonstrated that austenite may form at temperatures considerably below those at which the reaction is first observed during continuous heating. Because of this discrepancy, tempering is sometimes performed above the true critical temperature and in these cases austenite forms during tempering. The lowest temperature at which austenite forms and the kinetics of the reaction have been studied by Bain,' Bleakney and Gros-venor,2 and Dube and Cunningham. This austenite can affect the properties either as austenite per se, if it is retained at room temperature, or as a decomposition product if it transforms. The effect of austenite formation during tempering on low temperature impact properties of an 8 1/2 pct nickel steel was reported by Brophy and Miller4 in work published after the present investigation was initiated. They concluded that the improvement in low-temperature notch toughness which followed tempering at certain temperatures could be attributed to the austenite formed during tempering. Kramer et al.5 found anomalous hardness increases and embrittlement after tempering of a low-carbon manganese-nickel steel. They concluded that austenite formed during tempering, and that the decomposition products were responsible for the increase in hardness and the embrittlement. Quan-titative correlations of the microconstituents and mechanical properties were not made by these investigators. The present study was undertaken in order to establish the kinetics of formation of austenite at various temperatures, the characteristics of the decomposition of this austenite, and the relationship between mechanical properties and the phases present. Experimental Procedure A low-carbon manganese-nickel steel was selected because of the sluggishness of its austenite decom-position reactions. The composition of this steel in percent was: C, 0.10; Mn, 3.52; Ni, 2.34; Mo, 0.52; Cr, 0.17; Si, 0.19; V, 0.15; P, 0.019; and S, 0.020. Samples were prepared by forging sections from a large ingot to 3/4 in. bars. Formation and decomposition of austenite were investigated by dilatometric techniques which were checked by X-ray measurements. Dilatometer specimens were hollow cylinders 1 in. long, 1/2 in. diam, with a 1/8 in. central hole. All specimens were aus-tenitized for 1 hr at 1650°F and quenched in water prior to insertion in the dilatometer. Oxidation was prevented by using an inert atmosphere of purified nitrogen. Dilation was measured with a dial gauge which could be read by interpolation to 0.00005 in. Temperature was maintained within ± 3°F by a Brown Electronik Controller. Chromel-alumel thermocouple leads were welded to opposite ends of the specimen with the specimen serving as the hot junction. As a check on temperature uniformity comparison was made of the specimen temperature as measured with the chromel-alumel leads and the temperature of the center of the specimen as measured with a calibrated platinum—platinum-rhodium thermocouple embedded in asbestos in the central hole of the specimen. During heating a 5°F temperature difference was noted below 1000°F, but none above, while in cooling, a 5°F difference was observed from 1300" to 735°F, but none below. Heating rates of 35°F per min and cooling rates of 60°F per min were employed for all dilatometric studies. For transformation studies below room temperature, the dilatometer was allowed to cool to 150°F and then was quenched into liquid nitrogen.

Jan 1, 1951

By Carl H. Samans

In their recent complete review of the subject of age-hardening,' R. F. Mehl and L. K. Jetter classify the main types of precipitation-hardening alloys under two headings, depending upon the nature of the precipitate and the character of the precipitation. In the alloys falling under the first heading, which display "continuous precipitation" and are typified by the aluminum-copper alloys, "precipitation seems to occur without much regard to grain boundaries and apparently at much the same rate at every point," although an acceleration in regions plastically deformed has definitely been established.2 In the second type of alloys the precipitation is "discontinuous," as in the copper-silver system for example, and "seems to start in restricted regions, primarily those contiguous with the grain boundaries, and to spread inward in an advancing wave." The reasons for the occurrence of these two greatly different types of precipitation are unknown, as are those for many other reactions that take place in the solid state. In the present paper only the first or "continuous" type of precipitation will be dealt with, for which a complete crystallographic mechanism has been worked out for the process of precipitation from a supersaturated solid solution of copper in aluminum. Based upon this mechanism, an explanation of the various property changes found experimentally will be developed in the second paper of this series. In later papers ('discontinuous precipitation" in copper-silver alloys will be explained, and an effort will be made to rationalize the two processes and types of precipitation. Crystallography of the Precipitation Process Through the extensive investigation by R. F. Mehl, C. S. Barrett and F. N. Rhines3 on the Widmanstätten structure in aluminum-rich copper

Jan 1, 1940

By Carl H. Samans

In their recent complete review of the subject of age-hardening,' R. F. Mehl and L. K. Jetter classify the main types of precipitation-hardening alloys under two headings, depending upon the nature of the precipitate and the character of the precipitation. In the alloys falling under the first heading, which display "continuous precipitation" and are typified by the aluminum-copper alloys, "precipitation seems to occur without much regard to grain boundaries and apparently at much the same rate at every point," although an acceleration in regions plastically deformed has definitely been established.2 In the second type of alloys the precipitation is "discontinuous," as in the copper-silver system for example, and "seems to start in restricted regions, primarily those contiguous with the grain boundaries, and to spread inward in an advancing wave." The reasons for the occurrence of these two greatly different types of precipitation are unknown, as are those for many other reactions that take place in the solid state. In the present paper only the first or "continuous" type of precipitation will be dealt with, for which a complete crystallographic mechanism has been worked out for the process of precipitation from a supersaturated solid solution of copper in aluminum. Based upon this mechanism, an explanation of the various property changes found experimentally will be developed in the second paper of this series. In later papers ('discontinuous precipitation" in copper-silver alloys will be explained, and an effort will be made to rationalize the two processes and types of precipitation. Crystallography of the Precipitation Process Through the extensive investigation by R. F. Mehl, C. S. Barrett and F. N. Rhines3 on the Widmanstätten structure in aluminum-rich copper

Jan 1, 1940

By W. J. C. Venter

The use of activated carbon to improve the selectivity in the separation of base metal minerals from bulk concentrates played an important role in the development of separation techniques employed at Tsumeb and Kombat mines. The Kombat mine, owned and operated by Tsumeb Corp. Ltd., is located in the Otavi Valley in the northern part of South West Africa, approximately 213 air miles north of Windhoek and 38 air miles south of Tsumeb, at latitude 19° 43'S and longitude 17º 41'E. The mine is linked to all major centers by both national railroad and tarmac highway systems which pass right through the town. The Otavi Minen- and Eisenbahn-Gesellschaft (OMEG) mined ore on the farm Asis from 1908-1925. Tsumeb Corp. Ltd. acquired the mineral rights in 1947, started diamond drilling in 1954 and commenced mine development in 1960. The mill started production in 1962 when proven ore reserves were 3,378,084 st containing 2.85% Cu and 2.90%Pb. Annual production of 248,411 st was increased in May, 1967 to the rate of 422,990 st, which was still being maintained in 1971, when ore reserves stood at 3,054,701 st of grade 1,91% Cu and 2.5% Pb.

Jan 4, 1973

By Carl Henrich

In the planning and erection of smelting-works, especially of such as contain the modern large water-jacketed blast-furnaces, we are often confronted with an insufficiency in the watersupply. It may be impossible to find in the immediate neighborhood of the selected site a sufficient supply to furnish the jackets with cold water. Or there may be enough water for this purpose, but it may be highly charged with scale-forming minerals held in solution. Or, the main water-supply, if pumped from the workings of a mine, may carry iron- or copper-salts, or even some free acid in solution, all of these substances being derivable from the oxidation of sulphuret-ores in the mine. Moreover, such mine-waters sometimes contaminate the waters of the creeks, so that these become unavailable, and we have to fall back on an inadequate supply of pure water furnished by some spring or springs, entirely too small in

Jan 1, 1896

By Benjamin LeRoy Miller, Joseph T. Singewald

The ore deposits at Firmeza have been worked continuously since 1884; those at Daiquiri since 1895. It is surprising, therefore, that they have not been the object of careful geologic study until quite recently. It is true that considerable attention was paid to these deposits by A. C. Spencer, in 1901, in the report on the geology of Cuba, by Hayes, Vaughan, and Spencer,l but this was only incidental to a hasty general reconnaissance of the Island. As far as the Daiquiri deposits are concerned, this gap has been filled by the appearance of the two papers by Prof. James F. Kemp2 and by Prof. Waldemar Lind-gren and Clyde P. Ross respectively.3 Max Roesler, first holder of the Emmons fellowship, made a detailed study of the Firmeza deposits during the past summer, so that soon we can expect a full description of them. Consequently, there is no, demand at the present time for a description of the deposits from other sources, and that is not the purpose of this paper. The papers on Daiquiri, however, leave unsolved problems in regard to the age of the rocks of the district and certain phases of the genesis of the deposits, and it is with the hope of aiding in the solution of some of these problems that this contribution is offered. Kemp, and Lindgren and Ross agree in assigning these deposits to the type of contact metamorphic deposits. They disagree in part on the question of their localization. The deposits occur in an extensive area of diorite which includes numerous blocks of limestone, and sometimes are found in the contact zones between these blocks and the diorite, and in other instances are completely enveloped in the diorite, showing no apparent connection with the limestone. The latter class includes

Jan 1, 1916

By C. H. Jr. Herty

IT Is well known that manganese will desulfurize molten iron through the formation of manganese sulfide, which, being only slightly soluble in the metal, rises to and enters the slag where it remains as such (mixer slag) or is converted partly or wholly to calcium sulfide (basic open¬hearth slag). The reaction by which manganese sulfide is formed is Mn + FeS = MnS + Fe. This reaction is generally considered to be reversible, although McCance1 states- that such is not the case. The experimental work was carried out to confirm the results of Rohl2 as to the reversibility of the reaction. Six trials are herein considered. In each 200 grams of electrolytic iron free from manganese and sulfur were melted in a pure zirconia crucible in a carbon resistance electric furnace. To the melted iron in runs 2, 3 and 4 metallic manganese and manganese sulfide were added to give 1, 2 and 4 per cent. manganese respectively, with 0.50 per cent. of sulfur in each. In runs 5, 6 and 7, metallic manganese andiron sulfide to give the same proportions of manganese and sulphur as in runs 2, 3 and 4, were added. The melts were held molten in the furnace for an hour and then cast into small ingots.

Jan 2, 1925

By W. C. Smith, P. J. Hickey

After a short historical background of the process evolution, this article descvibes present-day plant facilities and operating techniques utilized for high-purity bismuth production. The plant is one of the world's largest, with an annual output of some one million pounds of refined bismutlz. PREVIOUS papers1 written by staff members of Cerro de Pasco Corp. have referred briefly to the production of refined bismuth. Since the Corporation is one of the world's foremost producers of high-purity bismuth, a detailed description of the process for extracting the metal may be of general interest. Following a short historical background of the development of the actual process, this presentation will trace the progress of bismuth from its entry into the primary smelting circuits to its concentration in electrolytic lead cell slimes. Our facilities for the treatment of anode muds will be described and the extractive methods given in some detail, with particular emphasis on the techniques which result in the production of refined metal. HISTORICAL BACKGROUND Shortly after Cerro de Pasco began smelting operations at Oroya, Peru in 1922, it became apparent that the dust carried by copper converter gas contained appreciable amounts of bismuth. Although dust collection efficiency was poor prior to building of the 550-ft stack and installation of the central cottrells in 1938, a large stock of dust was accumulated during the intervening years, having the following approximate composition: Oz. per ton Ag - 11.0 Pct Sn — 0.5 Pct Pb - 49.0 Pct Zn - 6.5 Pct Bi - 2.0 Pct Insol. - 1.5 Pct Cu - 0.7 Pct Fe - 2.3 Pct Sb - 3.0 Pct S - 10.0 Pct As - 7.5 In the mid-1920's, experimental crucible melts of this dust with carbon indicated that most of the bismuth and silver, and some of the lead, could be reduced to a fairly clean bullion. Other products were a small amount of leady copper matte and a slag high in zinc, arsenic, antimony, and lead; this slag contained some tin but only small quantities of silver, bismuth, and copper. After the laboratory results had been confirmed by operation of a small reverberatory, a dust reduction furnace was constructed. The ±10 pct Bi-Pb bullion produced from this operation was stocked until 1930, when an Oroya-designed converter type furnace3 was installed for the elimination of arsenic, antimony, and some lead from the bullion. This process concentrated the bismuth from 10 to about 60 pct. By means of the bismuth process developed4 by W. C. Smith at East Chicago (1909-1914) and the discovery of a method5 for separation of lead from bismuth with chlorine gas in 1929, it became possible to begin production of refined bismuth. Unfortunately, bismuth deleaded with chlorine always contained residual chlorides, and the removal of the chlorides by caustic soda left a lead content of 0.02 to 0.04 pct. This final problem was solved6 by substitution of air-blowing for the caustic treatment, which effectively removed all excess chlorine and gave bismuth which was practically lead-free. In 1934, a pilot electrolytic lead refinery began operations at Oroya. Lead smelting was resumed in 1935 and two years later a 100-ton-per-day lead refinery was put into service. In conjunction with the latter, the present-day Anode Residue Plant was constructed. Until 1940, the plant treated both lead anode slimes and dust reduction bullion. The dust reduction furnace was shut down in that year, and all cottrell dusts (with the exception of the product from the arsenic cottrell) were mixed with pyrite and treated in a Wedge roaster to eliminate all possible arsenic. Calcine from this operation joined the sinter plant feed; hence the bismuth from the copper and lead circuits was collected in the lead bullion and subsequently in lead anode slimes from the electrolytic lead refinery. The latter source has been the only bismuth-bearing material of any consequence entering the Anode Residue Plant from late 1940 to the present. A copper refinery began operating in 1948, and the cell mud from this plant is mixed with lead slimes and processed through the same circuit, though only a small quantity of bismuth is present in electrolytic copper cell residues. BISMUTH INTAKE Present-day routes which are followed by the new bismuth feed from its entry into the primary smelting circuits to its arrival at the Anode Residue Plant are traced schematically in Fig. 1. As illus-

Jan 1, 1962

By J. E. Harris

The metallic elements, beryllium, calcium, cerium, lithium, manganese, titanium, vanadium and zirconium are used in metallurgical practice in relatively small percentages for the purpose of improving the physical properties of various alloys. No important uses for any of these elements have thus far been developed either in the pure form or in alloys of which they constitute the major constituent.

Jan 1, 1935

By WILFRED SYKES

THE story of the rolling of strip steel is not limited to any one plant or individual or group of individuals. It is a story with many ramifications. First of all, it should be understood that the strip mills we are considering are continuous mills, in that the steel passes directly from one mill to the other in a more or less straight line. Continuous mills are not new; in fact, they have been used for many years in the rolling of a few simple shapes. They were, however, driven by one motor through jackshafts, and as a result the speed of each roll stand had a fixed relation to that of every other stand in the series. This in turn fixed the reduction that could be made in each stand. The mill could produce simple things, but was not satisfactory for the production of the variety of strip now required. It was, therefore, necessary to get away from the restrictions of that kind of drive. To accomplish this, the designer could either separate

Jan 1, 1936

By A. B. Parsons

LAST YEAR (1934) saw the completion of a ten-year program of reconstruction and modernization of the world's largest lead- smelting plant, that of the ' Broken Hill Associated Smelters Proprietary, at Port Pirie, South Australia, which has a capacity for smelting and refining 220,000 (short) tons of lead per year. It deals with the entire output of lead concentrates from the famous Broken Hill district in Australia, being owned .jointly by the three leading companies: North Broken Hill, Broken Hill South, and the Zinc Corporation. These companies, together with the Sulphide Corporation, are credited with a production of 198,000 tons of lead in 1934. When one says regarding any metallurgical plant that modernization is "completed" he should add "for the moment." Development in the art of metallurgy and in the equipment used never ceases; that which seems close to the last word today is likely to be obsolete in a few years even in a process so well standardized as smelting and refining lead. However, the reconstruction at Port Pirie has altered the procedure materially. More im-

Jan 1, 1935

By Leland Wemple

PREVIOUS to 1915, zinc refining had not become a general practice among the zinc smelters in the United States. Such refining as had been carried on was confined chiefly to remelting very high-leaded zinc, such as third-draw metal from the retort furnaces, and slab dross, and hard spelter from galvanizing pots. In this remelting operation, the lead and iron were settled out and the refined spelter obtained graded fifth class, i.e., Prime Western. Owing to the presence of lead in most zinc ores, the bulk of the spelter produced by direct smelting is of this Prime Western grade. Careful selection of ores of low lead content gave purer grades of spelter, i.e., Brass Special and Intermediate; and smelters which could secure ores carrying practically no lead produced high-grade spelter. Thus, in general, the grade of spelter produced by any smelter was pre-determined by the purity of the ore it could obtain. The needs of the warring nations of Europe for enormous quantities of cartridge and other high-grade brass resulted in such a demand for the purer grades of spelter that the available supply of lead-free and low-lead ores could not produce the quantity required. Prime Western grades went begging, so to speak, while high grades sold at times from 5 to 15 c. per pound over the Prime Western market. The great demand, coupled with the wide market margin, which permitted the inherent costs and losses, resulted in the conversion of the lower grades into higher grades by processes of refining. These conditions also accentuated the development and size of the electrolytic plants, which were being worked out at the time this increased demand for pure grade of metal occurred. The electrolytic process, where available, produces a higher grade of spelter from impure ores than does the fire process; a large portion of those impurities in the ore, which by the distillation process would be carried into the spelter, are removed in the leaching of the ores and the purification of the solutions. The refining process, adopted at a number of smelters for the purpose of converting low-grade spelter into "grades suitable for brash was that of redistillation.

Jan 11, 1917

By F. X. Meyer

THE United States Smelting Refining and Mining Company maintains an ore-purchasing department for procurement of custom tonnages of milling and smelting ores and concentrates for treatment at its Midvale plant. Arrangements with other companies provide for treatment of Company and custom zinc concentrates. Location of the Midvale plant in the heart of the Western mining country makes it possible to serve shippers from these nine producing states: Arizona, California, Colorado, Idaho, Montana, Nevada, Oregon, Utah, and Washington. Shipments from most of these states travel over main-line railroads, delivery being made at Midvale within a short time after billing of the shipment. Shipments varying in size from a few sacks to carloads can be handled at

Jan 1, 1948