Search Documents

By P Kittler

In the spectrum of mining-related disciplines, geometallurgy sits between resource geology and metallurgical engineering. Unlike its neighbours, it is a relatively young discipline and its concepts, procedures and techniques are still evolving. Relevant geometallurgical issues differ from one deposit to the next so there is no single template that can be used in all situations, meaning that geometallurgy programs are nearly always customised and tailored to the deposit and the situation.Over time, a number of key mistakes are seen to emerge regularly. The eventual impact of these mistakes can vary from suboptimal performance of mine and plant to complete failure of the operation. For instance, poor characterisation of ore lithologies and their spatial distribution can have negative impacts on processing plant throughput. However, when combined with failure to identify critical blending constraints it can result in a totally inoperable plant.A number of common mistakes committed during geometallurgical programs are discussed and some preferred alternative approaches are suggested

Sep 5, 2011

LIST OF CONTENTSAbstractIntroductionSelected Sections of the Broken Hill LodeLocality PlansPetrology1. Zinc Corporation Mine: DDH. 5.98, section 30, No. 26 level2. Zinc Corporation Mine: DDH. 838, section 30, No. 13 level3. Broken Hill Sonth Mine: 60 ft. cont01(r above 1170 ft. level4. Broken Hill South Mine : No. 7 shaft section, 1370 ft. levelOrigin of garnet sandstone5. Barrier Central Pty. Ltd.: DDH. tJ.93, Block 136. North Broken Hill Ltd.: Junction mine, DDH. 602, No. 10 level7. North Broken Hill Ltd.: Jnnction mine, DDH. 588, No. 11 level8. North Broken Hill Ltd.: North mine, DDH. through Southern ore body, 3370 ft. level9. North Broken Hill Ltd.: North mine, Northern ore body above 2300 ft. level(a) Southern end, section 27, 77 ft. above rails(b) Northern end, section 30, 6.9 ft. above rails(c) Miscellaneons samples, sections 27 and 28Relative time of ore depositionSericitizntionStructural significance of sericitizationGCLhnite OrthoclaseApatite GarnetManganese SilicatesAlteration of manganese silicatesRelation of zinc and lead to the silicatesZinc in manganese-bearing silicatesLead in potassium and lime silicates and apatite

Jan 1, 1959

Good morning. I am very pleased to be invited to present the Opening Address to this inaugural New Zealand Minerals & Mining Conference. It is indeed a pleasure to see so many representatives of this industry, which is so important to New Zealand's economy, present here today.   I extend a warm welcome to all delegates, particularly those from outside New Zealand. To those of you who have travelled from offshore, please closely observe our industry, and do not hesitate to ask Crown Minerals staff here for any further information you may want. I trust you will soon come to the same conclusion that my two following speakers have; that New Zealand is a good investment destination, and further that many of you will decide to invest in New Zealand's minerals and mining industry.   In New Zealand the minerals industry - minerals, coal and petroleum - together constitute an approximate $2.5 billion per year business. In broad terms this is about 3% of our Gross Domestic Product.

Jan 1, 1997

By P Vasconcelos, X D. Deng

Numerous supergene manganese oxide deposits are developed inSouth China as a result of weathering of a thick sequence of Paleozoic marine Mn-bearing sedimentary rocks, consisting mainly of limestones, cherts and black shales that were intensely folded and faulted due to multiple episodes of tectonism since the late Triassic. The ore minerals are dominantly pyrolusite, cryptomelane, nsutite, lithiophorite and braunite. The supergene manganese ores contain Mn ranging from 20 to 44 wt per cent; manganese oxide deposits derived from cherts and black shales also contain recoverable levels of Co, Ni, Cu, Pb and Zn. 40Ar/39Ar dating of potassium-bearing manganese oxides reveals that extensive supergene manganese ore formation started at least in the earliest Miocene and persisted to the Present. Ages of the deposits show a close correlation to tectonic stability, with the oldest in tectonically quiescent areas and the youngest in active areas that have subjected to continuous uplift and thus significant denudation. The prolonged wet and hot climate since Oligocene and the balance between weathering and erosion, which is parameter to the tectonic stability, are the ultimate controls on the formation and distribution of South China supergene manganese oxide deposits. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By G Senanayake, K Hazarika

The demand for iron-ore is ever increasing with the industry directly employing 60 500 people in a range of highly skilled roles in Australia. In the year 2019, the global iron-ore production was 2.85 billion tonnes. It is estimated that each tonne of beneficiated iron ore produces 400 kg of tailings. The IOTs are fine, dense and stable crystalline material mainly composed of iron oxides, alumina and silica. The current and most applied method of iron-ore tailings (IOTs) disposal is using subaqueous disposal of tailings in dams. The footprint generated by a tailings dam is massive and requires constant monitoring due to the possibility of a failure making the operation and maintenance of tailings dam extremely expensive. This review briefly discusses the known causes of tailings dam failures, their impact to the environment and day-to-day human life and potential applications of IOTs. The increase in water content enhances the pressure on dam walls. This in turn increases the liquefaction potential of the tailings and reduces the overall strength of the dam making it more vulnerable to failure. Potential applications of IOTs are in paints, aggregates in construction materials and bricks. The reuse of IOTs reduce waste and generates further revenue facilitating a path towards a sustainable future for the industry.

Nov 8, 2021

Production sharing and cost apportionment in joint ventures is commonplace in Australasia today and elsewhere. It is a recognised convention that, with the exception of a free carry situation, joint venture participants usually share the proceeds of the joint venture in direct proportion to their respective participating interest, after having first paid its respective cash calls, in advance, to cover the projectÆs ongoing operating and capital cost requirements.In surface mines, the parties simply pay their way and take their proceeds in this manner. In underground mines, the situation is no different, though treatment of capital, depreciation and tax may differ between the parties. A common feature in many cases is the creation of a joint venture entity to conduct the business. This entity then collects cash from the parties, banks it, employs the staff, runs the operation, provides reports and pays out the proceeds. This convention appears to be relatively simple in application. In practice, it has been known to be complicated in the situation where the participants take their product at the mine gate and undertake their own marketing and selling arrangements. A more complex situation presents itself where the joint venture tenement boundary with an unrelated third party straddles an economic deposit. In this scenario, both the joint venture parties and the third party may wish to mine the deposit, sharing some infrastructure and costs, yet taking their own product as it is produced. A case study outlining such a situation is presented in the paper, outlining firstly how the major cost categories were identified and treated for cost apportionment purposes. Secondly, a mechanism for the equitable apportionment of product is suggested. Finally, issues such as timing and cost reporting are dealt with, together with a checklist of points which should be considered when a similar situation might arise in the future.

Jan 1, 2002

By P Goblet, S A. Séguret, E Cordier, A Galli

In salar-type deposits, lithium grades can be measured by bailers introduced at different elevations in the drill holes at locations where, later, the brine will be pumped out to recover the metal. When they are duplicated, these a priori rudimentary measurements may show large differences without indicating whether this is due to the procedure itself or to some physical causes linked to the dynamic behaviour of the salar (seasonality, rainfall, underground flow etc). In the reservoir presented in the paper, the problem is complicated by the double lack of stationarity of the lithium grades: the grades not only increase importantly with the depth but at the same time their fluctuations decrease, making it necessary to use non-stationary geostatistical techniques to simulate them. Reservoir simulation is developed in two steps: first, geostatistical simulations of the lithium grade create possible realisations of the reservoir; then, each geostatistical simulation is followed by a pumping simulation that calculates, at each drill hole of a given extraction scenario, the lithium produced each year over 40 years. For the set of 100 simulations produced in this way, a scenario reduction is made to choose the five most representative simulations where more complex calculations will be carried out (for example, changing hydrogeological parameters such as porosity and permeability, or the elevation of the filters, the number and the location of the pumping and the reinjection drill holes etc). The paper first presents an analysis of the geostatistical model sensitivity to the grade uncertainty when measured by bailer. Among the 100 measurements at our disposal covering the future production domain, 50 per cent are duplicates measured at the same place but at different times. They are randomly sampled to produce five subsets of 75 values, which will constitute the future 3D conditioning points for the geostatistical analysis and the simulations. For each subset, trend, standard deviation and variogram models are fitted, leading to five sets of 20 geostatistical simulations of grades. In this way, the reliability of the different parameters involved in the procedure is evaluated, as well as its impact on the pumping results. Then, a reconciliation study is conducted between the non-stationary nugget effects encountered in the 3D variograms of the lithium grade and a pure statistical analysis of 25 duplicates measured at different locations and/or different times. The result is that if the nugget effect reaches 20 per cent, which is the case of three conditioning subsets out of five, the reconciliation is good and the nugget effect of the variogram model represents the bailer uncertainty, ie the measurement error. Since the geostatistical simulation incorporates a nugget effect, it handles the bailer uncertainty and the impact on the produced metal is included in the evaluation. The final conclusion is that, after the hydrogeological pumping simulations, the initial differences between the five geostatistical models do not influence the final results: lithium grades measured by bailers can lead to a robust evaluation of the extractable resources, a conclusion that conflicts with conventional wisdom.CITATION:Séguret, S A, Goblet, P, Cordier, E and Galli, A, 2017. Bailer uncertainty evaluation in a lithium salar deposit, in Proceedings Eighth World Conference on Sampling and Blending , pp 395–402 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By E Mielczarski

Determination of the adsorbed layer composition and structure at molecular and atomic levels and understanding adsorption mechanisms and dynamics are vitally important for the preparation of surface layers with specific functions. Direct information, at a molecular level, about mineral surface composition, its structure and surface distribution is crucial to perform an efficient separation process for mineral beneficiation. This information is equally important for modifying surface properties of industrial minerals for specific applications such as: fillers, composites, weathering resistance, etc. An understanding of the mechanisms and kinetics of the interaction of first adsorbed organic molecules with mineral surfaces is a fundamental requirement for the prediction and control of the macroscopic surface properties governing the efficiency of separation technologies or new material formulations. The developed infrared external reflection technique has a unique ability to study interface phenomena, at a molecular level, on heterogeneous substrates. The variety, precision and reliability of information about the interface phenomena delivered by this technique is superior to any other single technique. The experiments are fast and non-destructive. High sensitivity (starting from 20 per cent of the monolayer) in situ collected information in a multiphase system, even in the region of strong absorption of the substrate, makes this technique a very valuable experimental tool. The complexity of the recorded reflection spectra, their sensitivity to variations of the optical properties of all bulk and surface components and their spatial distribution in the system under investigation, are in fact the major strengths of this technique. A few examples of the application of this multi-diagnostic technique, for monitoring surface modifications of semi-soluble minerals for selective flotation, will be discussed in detail in this paper.

Jan 1, 2005

Stripping of Fe (III) from D2EHPA Using Different Reagents The common way to extract Fe(III) from an organic solvent is by using concentrated acidic solutions. The stripping of Fe(III) from organic solvent Di-2-ethylhexyl phosphoric acid (D2EHPA) by hydrochloric acid (HCl) solutions has been found to increase with increasing the acid concentration. However, the use of a concentrated acidic solution such as 6 M HCl can degrade the organic molecules. In this research, to increase the efficiency of Fe(III) stripping from D2EHPA, effect of some acids, salts and buffer solutions was studied. Influence of Tri-butyl phosphate (TBP) as modifier on the Fe(III) stripping operation was also investigated. According to the results, the best Fe stripping recovery was achieved in the presence of low acid concentration and the salts which was 72.4 per cent oxalic acid, 70 per cent ammonium oxalate and 75 per cent buffer of oxalic acid and ammonium oxalate. The results also showed a better recovery in the presence of the buffer rather than the salt. Finally, increasing the concentration of TBP, HCl and H2SO4 resulted in a higher stripping efficiency of Fe(III). However, in the presence of oxalic acid and its salts increasing the reagent concentration did not increase the stripping efficiency and at this condition, the recovery of iron remained constant.

Sep 13, 2010

By M W. N Buxton, M S. Shishvan, J Benndorf

The flow of information, and consequently the decision-making along the chain of mining from exploration to beneficiation, typically occurs in a discontinuous fashion over long timespans. In addition, due to the uncertain nature of the knowledge about deposits and the inherent spatial distribution of material characteristics, actual production performance in terms of produced ore grades and quantity and extraction process efficiency often deviate from expectations. Reconciliation exercises to adjust mineral reserve models and planning assumptions are performed with timely lags of weeks, months or even years.With the development of modern information and communication technology over the last decade, a flood of data about different aspects of the production process is available in a real-time manner. For example, sensor technology enables online characterisation of geochemical, mineralogical and physical material characteristics on conveyor belts or at working faces. The ability to utilise this additional information and feed it back into reserve block models and planning assumptions opens up new opportunities to continuously control the decisions made in production planning to increase resource recovery and process efficiency. This leads to a change in paradigm from a discontinuous method to near real-time reserve reconciliation and model updating, which calls for suitable modelling and optimisation methodologies to quantify prior knowledge in the reserve model, process and integrate information from different sensor sources, back propagate the gain in information into reserve models and efficiently optimise operational decisions in real-time.This paper introduces the concept of an integrated closed-loop framework for real-time reserve management, incorporating sensor-based material characterisation, geostatistical modelling under uncertainty, modern data assimilation methods for sequential model updating and mining system simulation and optimisation. The effectiveness of the framework and the value added will be demonstrated in an illustrative case study.CITATION:Benndorf, J, Buxton, M W N and Shishvan, M S, 2014. Sensor-based real-time resource model reconciliation for improved mine production control – a conceptual framework, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 223–234 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By A B. Christie

Stream sediment geochemical analyses from 140 mining company exploration surveys of the Coromandel, Northwest Nelson, Marlborough and Westland regions of New Zealand have been compiled from open file reports and entered on a database called REGCHEM (for Regional Exploration GeoCHEMistry). REGCHEM is supported by GEOEXPL, a custom-written computer software application which operates under the Microsoft Access relational database management system on a PC-type computer, The data are plotted as maps using the MapInfo geographic information system (GIS) package. Thresholds separating anomalous values from background values are determined using the PROBPLOT uni-variant statistical package, which enables the discrimination and modelling of several populations. Relevant REGCHEM data are being incorporated into a GIS for the Coromandel region as part of ongoing studies to develop mineral deposit and metallogenic models for the region, and to assess regional prospectivity.

Jan 1, 1995

A key driver to the success of a tunnelling project (the project) is the management of hydrogeological risk. The hydrogeological risk, if not managed, may cause significant impacts on the overall performance of the project. Impacts may include groundwater quality impairment due to contaminant transport and acid drainage from disturbed geology to groundwater, and groundwater lowering. The groundwater lowering and quality impairment may cause tunnel failure, with consequences such as injury to humans, as well as reduced property and environmental values, potentially costing millions of dollars to sponsors of the project. Depending on the nature of the contaminants and level of hydraulic connection of bedrock fracture along the length of tunnel, the contaminant transport may reduce structural strength of the tunnel due to corrosive action of contaminants such as acid drainage. The groundwater lowering can lead to varying degrees of ground settlement, posing threat of tunnel collapse. The management of hydrogeological risk includes:detection of potential pathways for contaminants into and around the tunnel,identification of factors responsible for the lowering of groundwater, and development of strategic measures to control groundwater lowering and contaminant transport. The paper presents an in-house hydrogeological risk management model named Vedanta-THRM (tunnel hydrogeological risk management). The model uses Risk Management Standard AS/NZS 4360:2004 (Standards Australia, 2004), Pressure State Response framework developed by Organisation of Economic Cooperation and Development, and Interaction Matrices. The Vedanta-THRM identifies important characteristics, processes and events of potential hydrogeological risk and develops control measures for managing hydrogeological risk throughout the life cycle of the project. The Vedanta-THRM was applied for a project in the early stages of planning and found to be useful in assessing, evaluating and reducing the hydrogeological risk in a managed approach that potentially increased the performance of the project. The application results also provided management options for use by project sponsors and insurance industry, which included tunnel risk financing options and options for equity investors to choose among various returns under different tunnel credit ratings.

Jan 1, 2008

By Woodcock JT

This paper deals with some innovations and current proposals for the treatment of gold ores and considers the possibilities of incorporating new developments in new or revised ore treatment flowsheets. The main topics considered are I. typical practice in relation to the size of gold particles, 2. concentration of coarse gold, 3. leaching reagents, 4. in situ leaching, 5. heap leaching, 6. carbon-in-pulp adsorption, and 7. treatment of complex ores (gold in pyrite, gold tellurides, and carbon-containing ores).

Jan 1, 1982

Study of Bauxite Separation by Using Flotation Column

Sep 13, 2010

By Johnson N. W

After an unsuccessful transfer from the laboratory to the pilot plant of galena flotation technology which used sodium metabisulphite and ethyl xanthate, laboratory flotation tests were conducted to identify any unusual variables which had a deleterious effect on the position of the lead rougher grade recovery curve for Hilton and Mount Isa silver-lead-zinc ores. Two variables (pulp temperature and contact time for ethyl xanthate and sodium metabisulphite) had important deleterious effects.The findings allowed a successful transfer of the laboratory process to a pilot plant scale process. The effect of temperature was important because the higher temperature (40°C) in the pilot plant pulp increased significantly the rate of reaction between ethyl xanthate and sodium metabisulphite. In the laboratory process at 20 to 25°C, the reaction rate was lower and did not interfere significantly with the process. The contact time for the two reagents was also important in the pilot plant scale process because of the higher reaction rate at 40°C.To employ ethyl xanthate in the pilot plant process, special precautions were required. Further, a collector (Aerofloat 241) from the dithiophosphate family was used successfully in the pilot plant process.

Jan 1, 1988

Advanced Jig Separation of Shredded Plastics The authors have reported that the RETAC jig is very useful in separating relatively low density particles such as plastics, and demonstrated that highly efficient jig separation of plastic components in discarded office machines is possible in pilot-scale tests. To further improve the separation efficiency, a hybrid jig (RETAC jig with air bubbler under the particle bed) which can separate plastics having similar specific gravities using differences in wettability produced by a pretreatment, and a reverse jig (modified RETAC jig for plastics lighter than water) were developed. This paper reviews the separation of shredded plastics using advanced jig separation technology (RETAC, hybrid and reverse jigs). Wettability control of the plastics for the advanced jig separation is also reported.

Sep 13, 2010

Laboratory and pilot plant investigations aimed at recovering gold as an electroformed sheet from gold eluate and gold leach solutions and slurries are discussed. The electrolytic test work undertaken makes use of high surface area electrodes, in particular nickel-chrome foam metal and activated carbon, as well as ultrasonic activation. The process involves initial gold electrowinning (or adsorption onto activated carbon), followed by gold electroforming, both operations being carried out in a specially designed reactor. The pilot plant work mainly involved the treatment of gold eluate solutions from a South African gold mine containing 600 mg/L Au: some tests were also carried out on gold leach solutions containing 6 mg/L Au. In the former case, very efficient gold extraction onto the foam metal cathode was achieved using electrolysis combined with ultrasonics. The polarity of the gold-loaded cathode was then reversed and, using a replacement electroforming electrolyte, gold was electroformed in situ onto a polished stainless steel mandrel, from which gold sheet was subsequently removed. In the case of leach solutions, pilot plant tests confirmed laboratory findings that in the presence of calcium (resulting from the lime used during the leaching process) no electrowinning is possible. Laboratory tests showed, however, that when sodium (in the form of NaOH or Na2CO3) is added to the leach solution, electrowinning can indeed take place. Alternatively, if a special activated carbon electrode is used (without current), the non-ionic calcium aurocyanide complex is adsorbed on to the activated carbon. When a gold-loaded activated carbon electrode is made anodic in a gold electroforming electrolyte, gold electroforming is feasible, although the efficiency is very low. The possible implications of these developments for gold recovery are further examined.

Jan 1, 2007

By Lynch K. S, Street R. P

Hamersley Iron's pellet plant at Dampier involves ore drying, dry grind- ing in ball mills, disc balling and, indurating by use of the straight grate system. After five years of operation, the plant's output has been increased from the design capacity level of 2 M.T.P.Y. to 2.5 M.T.P.Y. Steps taken in equipment modifica- tion, improvements in process control, and changes in maintenance procedures are described.

Jan 1, 1973

By Wright D. C

The operation of the cyanide-sensitive Mintek/TB1 kegold electrode was studied in the laboratory, with regard to equilibration time and drift, the effects of pH, stirring, salinity, dissolved oxygen, zinc and copper(I) ions. Methods for valid calibration in the range 20-600 mg(NaCN)/L and pH values in the range 9 - 12 in the absence of copper were also studied. Increasing the salinity beyond a threshold of 40 g(NaCI)/L improves calibration and measurement. The sensitivity is 91 mV per decade change in the concentration of ionic cyanide, and output is reproducible to within 10 mV with attention to the factors listed above. However, salinity of 40 g(NaCI)/L also sensitises the electrode to interference by copper(1) ions. This copper sensitivity seems capable of saturation, suggesting a research strategy for possible remedies.

Jan 1, 1996

By J MacNeil, R Dimitrakopoulos

As open pit mining of a deposit deepens, the cost of extraction may increase up to a threshold where transitioning to mining through underground methods is more profitable. This paper provides an approach to identifying an optimal depth at which a mine should transition from open pit to underground mining. The value of a set of candidate transition depths is investigated by optimising the production schedules for each depth’s unique open pit and underground operations. By considering the sum of the open pit and underground mining portions’ value along with the cost of transitioning corresponding to each candidate transition depth, the optimal transition depth can be identified. The optimisation model presented is based on a stochastic integer program that integrates geological uncertainty. As an input, the stochastic integer program utilises a set of several stochastic simulations that represent equally probable scenarios of the mineral resource. This group of simulations describes the uncertainty in the deposit, while the optimiser aims to maximise value based on discounted profits of both the open pit and underground components of the deposit.CITATION:MacNeil, J and Dimitrakopoulos, R, 2014. A stochastic optimisation formulation for the transition from open pit to underground mining within the context of a mining complex, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 363–368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014