Search Documents

Over the past seven years, a combination of New Zealand-, Australian- and German-led research voyages using the research vessels Tangaroa, Southern Surveyor, and Sonne respectively, have revolutionised our understanding of the Kermadec-Tonga arc-backarc systems. This convergent margin is the most seismically-active subduction zone system on Earth with convergence rates steadily increasing northwards from the Hikurangi Trench to ~250 mm/year at northern Tonga. In combination with the intra-oceanic setting, factors potentially producing magmatic, tectonic, and hydrothermal variability in this system include an increase in potentially subductable sediment northwards along-strike, intersection of the Louisville Ridge (hot-spot chain) and Osbourn Trough (paleo-spreading centre) with the arc at ~25¦S, and the possibility of Samoan (hot-spot) plume ingression in the northern Lau Basin. The bulk of the magmatism is submarine; whereas only a few emergent (some transient) volcanic islands exist, about 80 submarine volcanic centres of significant size (>1000 m above surrounding sea floor) are present between White Island in the south to north of Tafahi in Tonga. About 35 per cent of these centres are hydrothermally active. Important petrogenetic features of the volcanic rocks along this arc system are the abundance of rhyolite (some quartz-amphibole-bearing), and the outcrop of primitive olivine-clinopyroxene-phyric basalts in satellite cones of the major edifices. Many of the edifices consist of complex caldera systems. Eruptions from and degradation of these edifices were probably tsunamigenic. Many of the hydrothermal systems developed within the edifices are likely destroyed during the sector collapses which are the characteristic edifice degradation mode. There are three backarc spreading systems along this margin: the Havre Trough, Valu Fa-Eastern Lau Spreading Centre, and the nascent Fonualei Rifts. The latter are particularly notable in having captured the entire suprasubduction zone magmatic flux for a distance of about 150 km, shutting down the adjacent volcanic front arc volcanoes.

Jan 1, 2005

By Woodcock J. T, Sparrow G. J

Activated carbon particles obtained from a number of Australian CIP operations were examined with an optical and a scanning electron micro- scope and an electron microprobe. External surfaces, and polished sec- tions through individual particles, were examined with special reference to materials on the surface and to calcium and gold distributions. Photographs are presented of surface contamination of the particles by salts precipitated from the pulp such as calcium carbonate (calcite), calcium sulphate (gypsum), and a magnesium salt; ore minerals such as quartz, hematite, pyrite, arsenopyrite, pentlandite, and various alumino- silicates; and other substances such as grinding media and a fungus. Calcite was very abundant but the other materials were less common. Contamination in the interior of carbon particles was almost exclu- sively calcium carbonate, and extensive contamination extended to the centre of some particles. A possible mechanism for the formation of cal- cium carbonate inside the carbon particles is noted. Gold X-ray dot maps of sections through carbon particles indicated that gold was distributed throughout coconut shell carbons and that although gold was more concentrated near the outer surfaces of extruded peat carbon particles, it was also present to depths of at least 500 ¦m. The gold distribution throughout the carbon particles was similar to that rf alrit~

Jan 1, 1988

At Hilton Mine, 18 kilometres north of Mount Isa, the silver-lead-zinc sulphide bodies have undergone strong deformation in the form of folding and later faulting and brecciation in the hangingwall region of the mine. Variation in grades and widths over compara- tively short distances causes problems regarding accurate sampling of orebody exposures in underground development, and in defining confidence limits for the extrapolation of ore intersections in ore reserve calculations. The paper gives a preliminary insight into the problem of obtaining representative samples for exposed orebodies and discusses the sampling techniques employed. Results gained from these sampling methods could not be verified due to lack of individual bulk samples for comparison but strong evidence for precision was provided. INTRODUCTION In a developing mine like Hilton, accurate grade information is of extreme importance. Original grade information for a potentially viable ore deposit is gained from surface drilling, and initial ore estimates are calculated from the resultant ore widths and grades. After underground development has proceeded, the opportunity arises for detailed examination of orebody exposures, and the resultant assay grades and widths from sampling of these exposures may, in the long term,

Jan 1, 1976

By Munro DL

The Mary Kathleen uranium deposit is in north-west Queensland, approximately halfway between the townships of Mount Isa and Cloncurry, at long. 1400 009 E and lat. 200 44' S. The deposit Iwas discovered by prospectors of the Walton McConachy Syndicate early in July, 1954, and climaxed a very intensive ground search by hundreds of part-time prospectors. during the uranium boom from March to July 1954ò Numerous small deposits, mostly in the vicinity of Mount Isa, were discovered in various rock environments, but Mary Kathleen is the only large deposit and, apart from a few tons of hand sorted material from the Milo lease, is the only deposit that has been worked. Exploration of the surrounding area, and proving of the economic worth of the deposit, were conducted from the time of discovery until February 1956 by a geological team camped near the deposit. Proving was carried out by drilling a pattern of vertical and inclined diamond drillholes at fifty-foot centres over the outcrop. An adit was driven eastwards through the deposit. Metallurgical research and design work in the South Australian Department of Mines Adelaide Laboratories were based on core samples and bulk samples from the deposit. The signing of a contract in March 1956 with the British Atomic Energy Authority to supply 4500 short tons of uranium oxide allowed mining to commence, and enabled the planned construction of water supply, township and treatment plant to proceed. The open out mine and plant are now serviced by a modern township, four miles away, which is connected to Cloncurry and Mount Isa by road. Although little field work has been done since the exploration phase, this paper differs in interpretation from a previous paper (Matheson and Searl, 1956) in that it is based on a revised structural inter- pretation (Compana, 1958), detailed mapping of progressive exposures in the open out, and a re-examination of diamond drill cores.\

Jan 1, 1968

By Smith C. B

Major diamond pipes discovered in Western Australia in the late-1970s exhibited a number of unique features that not only resulted in Australia becoming the largest diamond producer in the world in volume terms by 1986 but also changed geological thinking on the primary occurrence of diamond. They were: - lamproite is an alternative primary diamond host to kimberlite. - the extremely high mean grade of the Argyle lamproite pipe at 5 ct per tonne. - the tectonic setting of the lamproite pipes in mobile zones mar- ginal to the Kimberley Craton in contrast to the traditional African setting within stable cratons. Diamond was one of the earliest economic minerals discovered in Australia but 128 years elapsed between its first recognition and the first Australian economic pipe discovery (Argyle). During that period some 200,000 ct of alluvial diamonds were mined in Australia (mostly in New South Wales), but such alluvial output is insignificant on the world scene where annual production today runs at 95 million ct of natural stones some 76010 of which comes from primary pipe sources such as Argyle which alone produces 30 million ct per annum. Of particular significance therefore is the geological nature of the primary diamond source rocks in Australia. The Argyle and Ellendale Pipes are lamproites, differing from kimberlite in their mineralogy and geochemistry, and characterised by the presence of typical lamproite minerals such as leucite, priderite, potassic richterite, and the abnormally high content of chemical elements incompatible with ultramafic rocks. But not yet widely appreciated is that many other Australian olivine-rich lampro- phyres also contain diamond. Such picritic alkaline rocks can

Jan 1, 1988

The most frequent initiation of coal dust explosion results from the ig- nition of high methane volumes, often at low concentration close to the minimum flammability limit, by a weak ignition source, e.g. frictional sparks. Tests performed in the 400 m underground test gallery of 7.5 m2 cross section indica- ted the following: 1. Methane at 200 m3 volume and con- centration 4.0 - 5.0 % CH4 may initiate the coal dust explosion. 2. Suppression of explosions result- ing from such initiation is very difficult, even when employing triggered, barriers.

Jan 1, 1988

By Ramani R. V

In this paper, a comparative performance evaluation of geostatistical, spectral, and fractal methods is made for short-scale variability prediction. The algorithms compared are: sequential Gaussian simulation method; a random fractal algorithm based on the generalised stochastic subdivision method; and a spectral simulation approach adopted for direct multi-dimensional simulation. The data for this study have been obtained from a mined out coal property. As this property was being mined, a 7315 m by 7315 m (24000 ft by 24000 ft) coal block was extensively sampled at an approximate spacing of 107 m (350 ft) and the 60-ton samples were analysed for sulphur in the 1.50 float gravity fraction. This data set is used here with the three methods to generate the simulated realisations, which are analysed for semivariogram reproduction and for simulation errors. Although all three methods converge to the true semivariogram in an average sense, the coefficient of variation of the average semivariogram for the Fourier integral method is minimum. The realisations generated by the sequential Gaussian method have minimum mean simulation error. The choice of a simulation method based on variability reproduction and simulation errors remains difficult.

Jan 1, 1995

The mining of remnant coal reserves at the Liddell Open Cut is subject to a number of risks. These risks are of both a technical and financial nature. Liddell Open Cut is principally a conventional truck and shovel/loader operation, supplemented by a highwall coal augering operation. There are significant areas of divergence from more conventional operations including working in close proximity to a major dam, working up dip from an operating underground mine, and working through areas where there has previously been underground extraction. In addition the site has major long-term rehabilitation requirements. This paper, rather than concentrating on specific detail of areas of risk, presents the spectrum of geological, design, operational and post-mining risks that accrue to the various areas of activity in this open cut operation. The balance of this paper then provides an outline of the strategies employed by Liddell Coal to manage their potential impact.

Jan 1, 1994

By Eren H

For a hydrocyclone of fIXed geometry, DC, Di, DO and ? are constants, the variable parameters affecting the performance are Qi, Fi, Du and H. (See Appendix 2 for definition of symbols).The relationship between d50c, Qi, Fi, Du and H gives models which can effectively be used for performance predictions. Such models have already been established by Lynch et al and by Plitt.These models have been tried in a limited manner under continuous operating conditions for on-line cowol. For on-line control effective and accurate instrumentation is required for which a new set up is proposed. Using this set up, a new model was established. A feature in this model is that deviations from the norm of operational parameters affecting d50c were considered. It is shown that these deviations generated by the disturbance of one or more of variations in the parameters, can be monitored by a computer and suitable signals generated to control servo mechanisms for restoring the required d50c value.The logic followed in developing the computer software is described and the application of the model is indicated.

Jan 1, 1990

By Grantham DL

ABS'TRACT For a number of years research efforts have been directed towards improving the efficiency of sampling and analysing coal mine roadway dusts. In the past decade the practicality of rapid, on site analysis of the incombustible content of these dusts using a radioactive technique has been receiving close attention both in Australia and overseas. Accurate measurement of the total incombustibles present is only possible by time consuming chemical methods. As the densities of the solid incombustible materials are greater than that of coal, they absorb a higher proportion of incident low energy gamma radiation than does coal. The amount of such radiation "back scattered" from mine dust samples is therefore inversely related to their average densities, and hence to their incombustible contents. This phenomenon can be used as a measure of incombustible content by employing an appropriately designed and calibrated instrument.

Jan 1, 1981

In order to satisfy environmental and mine operational requirements it is becoming increasingly important to minimise ground blast vibrations at certain locations. These locations are often in soil or on large resonant structures such as grain silos, highway bridges or even the walls of an open pit. A soil monitoring exercise was carried out to evaluate the common practice of coupling vibration detectors to the ground using spikes. At a series of locations in an operating quarry the spiked array response to single blastholes was compared with that of an accelerometer array attached to a calibrated embedded mount. The results clearly showed that the spiked arrays over-estimated the true ground vibration by 46.5 per cent on average, with a maximum observed error of 99.2 per cent. These errors are considered too large for compliance monitoring where accurate vibration levels are required for comparison with prescribed limits. Although spike coupling is convenient, its use for compliance monitoring should be viewed with caution. Unfortunately, however, many manufacturers supply their detectors as spiked arrays. A structural monitoring exercise was also carried out to evaluate the vibration response of a grain silo, highway bridge and a pit wall to the initiation of single blastholes. In this case accelerometers and standard geophones were firmly attached to the bridge which resonated at low frequencies. The results clearly show that, due to their limited low-frequency response, the geophones typically measured only half the true vibration level as measured by the accelerometers.

Jan 1, 1995

By P Gnnther, A M. van Niekerk

Coal mining operations in the Upper Olifants River Catchment in the Mpumalanga Province of South Africa are challenged with the increasing production of excess mine water that cannot be fully managed by existing practices of pollution control at source, recycling, and reuse on mining sites, storage and limited release to the natural water course. In contrast to this, the Olifants River Catchment is experiencing water stress and insufficient water is available to satisfy all water quantity and quality requirements for future industrial and municipal growth. It is estimated that the catchment has a deficit of 192 million m3 per annum if the reserve water requirements are taken into account. The future increased water requirements can be met by water transferred to the Olifants River Catchment from adjacent catchments. The cost of transferred water is likely to be substantially higher than the current cost of water supplied to local municipalities, commerce and industry. BHP Billiton and Anglo Coal Corporation are working together to jointly implement water management strategies that will contribute to the achievement of in-stream and dam water quality and aquatic objectives for the catchment. Consideration is now being given to the treatment and beneficial use of excess mine water. This will inaugurate a new era for the coal mining industry in South Africa, in which a pollution threat to the water resources in the Upper Olifants River Catchment is converted into a water source for beneficial use. Three potential mine water reclamation and reuse schemes have been identified and this paper details the technical, institutional, legal and financial considerations in the implementation of these schemes.

Jan 1, 2006

The major coalfields of Australia are almost unique in the occurrence in some areas of CO partly or almost completely replacing CH4,t1e normal seam gas from metamorphism of coal due to time and depth of burial. This CO2 situation has some benefits but mostly it introduces particular safety problems result- ing from the high density of CO2 relative to air, magnifying problems of gas dilution in ventilation, and the greater affinity which coal has for CO2 than for CH4 increasing proneness to gas-dynamic phenomena. The occurrence of most CO2 seam gas can be directly related to igneous intrusion and to its associated pneumatolytic injections. Whilst intrusions locally increase the rank of coal by their contact metamorphic effect, normal coal metamorphism due to time and depth of burial continues after intrusion and injection together with the ongoing metamorph- ic production of CH . This new CH slowly displaces any CO to leave some present-day intruded coals with seam gas with reduced CO2 or even without any significant CO2 associat- ions. The seam gas maps of the Bowen and Sydney Basins and more detailed maps of specific areas exemplify these situations. Mining progress, plus more searching studies of igneous-coal relationships provide improved understanding of the factors involved.

Jan 1, 1986

Any future developer of underground mining on the Bendigo goldfield will need to understand the unique geology and gold occurrence of this field. The development and sloping system employed will be primarily designed around these unique features. Modern techniques and equipment used in narrow vein mining will be applicable in this situation.The purpose of this paper is to examine the important geological features of the field as well as the known historical occurrences of the type of gold deposition in the ore bodies. This information will point to a system of development and extraction which will accommodate these features.

Jan 1, 1993

Knowledge of the hydrogeological setting of a mine forms an integral part of a mining operation. Groundwater impacts, initially, on mine feasibility. Then, on commencement of mining, it interacts on the operational components of dewatering, water supply, tailings leachates, mine wall stability, stormwater run-off, water disposal, impact on regional environment and mine closure planning. The recording of hydrogeological information is frequently overlooked during resource and reserve definition as well as during the course of mining when prime opportunity exists for the collection and collation of this data. In recent times, the exclusion of hydrogeological data has been exacerbated by use of high air pressure drill rigs that exclude water inflow. The recording of water data has been further inhibited by the use of computer coded drill logs that do not include the site geologistÆs or drillerÆs comments on drilling problems and observations associated with groundwater intersections. Geologists now infrequently directly supervise drill rigs, but visit the rig only intermittently to evaluate drilling progress. They do not see first hand drill performance characteristics at water make zones. Drill cuttings, as drill chips and cores, are now mostly logged away from the drill site so that wet sample locations, visual water flow evidence and verbal comments from the driller are not recorded. As a result, mine geologists now do not direct adequate attention to the delineation of lithologies and structures that store and transmit water. This paper provides examples of water sighting and recording techniques applicable to a mining operation. Examples are also provided where hydrogeological conditions have been disregarded with serious impact on the progress of mining. The recording of hydrogeological data should be maintained and formatted by the site geologists into a useful database for review as and when required by specialists in hydrogeology, geotechnical and mining engineering and the environment. The information can be coded by the site geologist for inclusion into the mine database. A groundwater dataset, compiled during the progress of field investigations, will save the considerable cost of re-drilling and hole re-entry testing which would otherwise be required to provide base level hydrogeological information required for progress of mining. Apart from working mine use, a hydrogeological dataset is a necessary component for planning mining closure and mine legacy conditions.

Jan 1, 2003

By Rowlands N. J, Zimmermann D. O

The Engel Model search simulator is described with particular emphasis on preparation of input parameters. The computer has a "black box" role in the same way a telephone or radio is a "black box" in communications. A search technique (sensor) is selected and applied in two stages of'search, namely, reconnaissance and detailed. The model relies on knowing and quantifying the parameters of the target sought and the search technique; this is usually done by analogy studies from available literature and experience. The parameters are then balanced by feasibility studies on the search area. Case histories show that the study makes the user aware of what he is likely to find rather than what he wants or needs to find to be viable. Two case histories are presented: one for Mississippi Valley type lead- zinc deposits and another for stratiform copper. The first study showed particular benefits in the input stage and highlighted the fact that one could expect a lot of encouragement by way of interesting results but with little chance of finding the high-grade,

Jan 1, 1974

By R Lurf, C Weber

In the frame of this paper a holistic dynamic process model approach is presented in order to introduce operational and technical excellence in drilling and blasting. Both on a macro and micro level the single process parts of drilling and blasting are outlined and their interaction is explained. The use of this approach for closing the gap between process planning and process implementation is explained and an example of the value generated is given.

Jan 1, 2007

By Hara Y, Arino S, Nakamura M, Tachimori M

The theoretical and experimental studies have been done to clarify the hearth flow of iron and slag. The results of dissections show that the hearth can be treated as a packed bed of coke hav- ing good permeability with a coke-free layer at the bottom of the hearth. 3-dimensional numerical calculations of hearth flow with and without a coke-free layer are carried out, and the results are assured by a water model simulation. The influences of a coke-free layer on the iron flow and the discharge route of iron and slag are examined. The 3-dimensional flow pattern can be represented simply by the travelling time, which depends on characteristically the profile of coke-free layer and the quantity of iron in the hearth. Those flow parameters could be obtained by the results of radioisotope tracer test ( Co for iron flow, and Sc for slag flow) at several furnaces. As a result, it is found that the coke-free layer repeats the cycle of appearance and disappearance at several-month intervals. This cycle corres- ponds to large temperature fluctuation at the bottom of hearth. The relation between iron flow and skull (solidified iron, coke and deposited graphite mixed layer) on the hearth brick was studied by the model experiment and the thermal analysis based on the indications of thermocouples installed in the bottom of the hearth. If a thin coke-free layer is formed on the skull, a fast iron flow is generated in the layer, and melts away the skull. The growth and melting of skull produces the fluctuation of thermal load on a bottom brick, causing brick Damage.

Jan 1, 1981

By S Robson, T G. Blenkinsop, S C. Dominy

Golden Pig mine is in the central part of the Southern Cross greenstone belt within the Archaean Yilgarn craton. The mine has produced approximately 2.5 Mt of ore at 5.7 g/t Au to yield approximately 450 000 oz. The majority of gold mineralisation is hosted within extensively deformed and quartz-veined BIFÆs. In addition to the BIF-hosted mineralisation, an increasingly important part of the resource lies in the Taurus Lode, which is a N-NNW-trending amphibolite facies shear zone. The Taurus Lode lies within a continuous shear-zone that has a moderate to steeply WSW dipping foliation, and a mineral lineation of biotite, amphibole and pyrrhotite plunging consistently 10¦ S. Drive faces, subperpendicular to the foliation and lineation, consistently show evidence for syn-mineralisation reverse shear. Exposures parallel to the mineral lineation and perpendicular to the foliation reveal both sinistral and dextral asymmetries. These characteristics suggest that the vorticity axis of the Taurus Shear Zone is parallel to the mineral lineation, and that the simple shear sense is reverse. This geometry can arise when there is a major component of flattening across the shear zone, which may be due to interference between two adjacent granite domes. The BIF-hosted lodes plunge consistently 15¦ NNW coincident with the intersection of the axial planar cleavage of the regional folds and the Taurus Shear Zone. However, where the penetrative shear characteristics control the orientation and geometry of the mineralisation, oreshoots plunge SSW, parallel to the stretching and mineral lineations within the shear. The SSW plunge of strike extensive and laterally confined high-grade, economic ore shoots within the Taurus shear is fundamental to defining the economic mineralisation within this lode. Identifying the zones of maximum continuity and establishing the optimal position for future development will maximise ore extraction.

Jan 1, 2003

By Hermulheim W

In the Federal Republic of Germany hard coal is mined underground only. The coal mines reach down to 1 500 m deep, recently having an average depth of 900 m. The commonly used winning system is long- wall mining with face lengths up to 250 in. The gate roads, which separate the seam into single panels, have an average length of one kilometre with a cross- section up to 20 m2. These single entries are usually supported by yielding steel arches. The installation of steel arches can hardly be mechanized. The choice of heavier support, caused by increasing depth and roadway cross-section, results in high cost for labour and material in gate roads. Furthermore, the heavy steel arch is acci- dent-prone, not only during installation but also during transportation and ship- ment. Rock bolts combined with a suitable lagging offer a way of mechanizing support work in headings. The aim is to decrease cost and to increase mine safety and pro- ductivity. Over the last ten years, 50 km of gate roads have been reinforced by a combination of rock bolts and weld mesh. Nevertheless, there are still differing opinions on the feasibility of rock bolting in gate roads. In Germany a long tradition and experience with steel arch support exists, whereas the function of an anchorage is a closed book to miners, preventing this new technique from spreading more quickly. Advantages and shortcomings of both steel arch support and rock bolting are compared. The experience with rock bolting up to now is reported. Possible improve- monts arm discussed.

Jan 1, 1986