Search Documents

By M R. Asef

Although generation of environmentally harmful hydrogen sulfide is considered to be related to sour gas fields, sweet gas reservoirs and waste fluids, travertine springs and geothermal fields may also produce acid gas (H2S and CO2) under certain conditions. The potential parameters influencing such a possibility need to be fully investigated to evaluate the extent of the consequences and predict hydrogen sulfide generation accordingly. Reports on hydrogen sulfide production at different regions and fields were gathered worldwide for the cases when some of them did not have such a problem previously. In order to inspect different aspects of these case studies, some other regions with no hydrogen sulfide content were selected as control. In all cases water samples were taken carefully for chemical analysis in the laboratory. Besides, mineral compositions were characterised in some cases for better evaluation. In order to give a thorough prospect of hydrogen sulfide production, a geochemical model was prepared. In situ engineering geological conditions, especially pressure and temperature, were assigned in the model to investigate the possibility of H2S generation using PHREEQC software. The results of modelling revealed that although many similarities existed between mineral compositions of the cases, certain formations were particularly prone to hydrogen sulfide generation. For better evaluation, important exchangeable cation ratios such as potassium/sodium, calcium/magnesium and ion proportions like sulfate and chloride were calculated as trends of the formations. As expected, the model could successfully monitor a higher ratio of SO42- and Cl- in potential H2S generator formations. Wide variation in percentage of HCO3- was considered as a secondary observatory parameter for better estimation. In addition, it was noticed that higher anion content created an environment ready to absorb any cations and this makes H2S generation easier. Finally, using correlations between predictors and estimators for low depth and deep samples defined the degree of effectiveness for every sample.

Sep 26, 2011

The Prince Lyell Mine has been the major production source at Mount Lyell since under-ground mining commenced in 1972.Three lifts of stopes have been mined to date, with the fourth, the 40 Series lift, to commence production this year. As the mine has progressed deeper, the ore haulage system has evolved to accommodate the mine's economic circumstances while maximizing efficiency.In the first, or 10 Series lift of stopes, ore was removed from drawpoints by L.H.D. units and tipped directly into rakes of 7 tonne rail cars. The original concept for deeper stoping lifts entailed L.H.D.'s tipping into long ore passes, rail haulage, underground crushing and hoisting to surface via the No. 1 Shaft. The suspension of the No. 1 Shaft project in 1976, due to economic difficulties, lead to the intro-duction of diesel truck haulage of ore, initially via the internal Prince Lyell Decline and now to surface via the Main Decline.

Jan 1, 1985

By M J. Nugus

The structural models developed by exploration and mining geologists are most commonly concerned with the ‘main structures’ or key constituents that pertain to the associated mineralisation. To this end, it is recognised that the geological and exploration models, which are developed, are essentially ‘fit for task’ and the scale-related variances are not always realised at an early stage. In fact, in many cases anomalous intercepts along different trends and of variable apparent continuity have often been neglected as ‘back scatter’ and not important. Recognition of the importance of subordinate structures as mineralising hosts suggests that additional opportunities exist outside the primary and main structures. History shows that opportunities are often not realised where gold is hosted in orientations not parallel to the predominant trend of the schistosity, main fault or shear zone.Another reason for the importance of subordinate structures can be understood from their roles in a percolation network. Subordinate structures can access the large fluid fluxes provided by backbone elements, but, as dangling elements, they provide greater opportunities for gold precipitation mechanisms and hence may constitute essential parts of the resource. Therefore, the role, understanding and consideration of the smaller-scale and orthogonal structures should be considered during all facets of exploration, resource development, delineation and mining.

Aug 22, 2011

By W A. Peck

Raise boring is the preferred option for constructing ventilation shafts in Australia. The trend has been towards larger diameters and longer single-pass shafts, and if at all possible, reaming through to the surface. The risk of raise failures, due to missed, unforseen or latent ground conditions has therefore been increasing, along with the need for better, more confident stability assessments.While the stability of specific weak zones and structures must be assessed individually, empirical rock mass classification schemes have been successfully used for about the last 20 years to assess general raise stability; eg the McCracken and Stacey method (M&S).Unfortunately M&S, as originally documented in McCracken and Stacey (1989), did not include a database of raise diameter and rock mass conditions versus actual performance. Nor was there a procedure for assessing the risk of failure due to adverse ground conditions. Peck and Lee (2008) published an Australian database of raise bore performance. Raise diameter and ground conditions, in terms of a lower bound Qr value, were presented for 50 cases versus raise performance. This paper updates the 2008 raise performance plot with more and SRF-corrected data. McCracken and Stacey (1989) had previously recommended that additional geotechnical data should be acquired and analysed when the proposed raise plotted on the unstable side of raisebore stability ratio (RSR) = 1.3, but the Australian data used in this study also suggests that all sites with Qr Contributions and sensitivities of various rock mass parameters (RQD, Jn, Ja, Jr, Jw, SRF, time-dependent weathering/deterioration) to raise stability and risk of failure are discussed. Numerous case studies are used to illustrate issues with stability assessments.As raises can now be remotely supported using sprayed fibrecrete, questions of time-dependency are also discussed. In recent times, contiguous piles, ‘mini-piles’ and grouting have also been successfully used to presupport or otherwise improve the stability of near-surface sections of weathered, or poor quality rock masses.

Mar 21, 2011

The Tregoora Gold Project is centred around the old Mitchell River Antimony Field located 100 kilometres west-northwest of Cairns, North Queensland. The project is currently the subject of a joint venture between Strategic Minerals Corporation N.L. and Hawk Investments Limited.Historical BackgroundThe Tregoora area was first prospected for antimony and gold around 1890. During the periods 1905 to 1914 and 1937 and 1944 approximately 100 tonnes of antimony and an unknown quantity of gold were won from a number of small mines the principal one being the "Retina". A strong increase in the demand for antimony in the early 1970's resulted in renewed exploration activity in the region and the re-development of the Retina Mine. Despite the intermittent interest in the region for antimony it was not until 1984 that the potential of the area for hosting gold resources was realised with the delineation by Strategic Minerals Corporation N.L. of a significant gold deposit now referred to as the Black Knight.

Jan 1, 1986

By C Killip

Working in Australia’s harsh climate can have a significant impact on the health, safety and productivity of our teams, but is our working environment expected to be more prone to heat stress in the future? Climate modelling suggests that we are likely to encounter more frequent heatwaves and higher apparent temperature. Does this mean that our teams will be at greater risk of heat stress, and are we prepared to deal with the changes in our future climate and the potential impacts on our working population? This paper will review the recent research on climate and projected changes to all meteorological parameters that are important in understanding the likelihood of heat stress. The paper will also describe the challenges encountered in the management of heat stress in a workforce, and then outline a systematic approach to heat stress management that will allow you to assess your own risk and manage your day-to-day operations into the future.CITATION:Killip, C, 2015. Future climate – is heat stress a real risk for the future and how can we better manage it?, in Proceedings Third International Future Mining Conference, pp 181–188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

Adsorption Behaviours of Humic Substances onto Iron Ore Particle Surface Humic substances extracted from lignite mainly consist of fulvic acids (FA) and humic acids (HA), which have been successfully used as good composite binders for iron ore pellets in laboratory tests and industrial production. However, there exists a general lack of understanding of the interaction between humic substances and iron ore particles surfaces. In this research, by means of zeta potential measurements, Fourier Transform Infrared (FTIR) spectrum, colorimetric method and Environmental Scanning Electron Micrograph (ESEM) imaging, the adsorption behaviours of FA and HA onto the surfaces of iron ore particles are investigated. The zeta potential results indicate that adsorption of FA on the iron ore particles can be characterised by specific and electrostatic interactions, while adsorption of HA is by electrostatic and chemical adsorption interactions. FTIR spectrum results show that adsorption force of FA on the iron ore particle surfaces is stronger than that of HA. From results of colorimetric method, compared with HA, adsorption amount and adsorption rate of FA is more and faster, respectively. FA molecule presents on the surface of magnetite in the shape of an araneose network structure according to the ESEM images, while HA molecule appears on the surface of magnetite in the form of small flocs or microclusters. Humic substances are effective to iron ore pelletisation. Comparsion of agglomeration results show that the different mechanisms of adsorption result in varied agglomeration behaviours. Theses findings above would be beneficial to the implications of composite binder for agglomeration.  

Sep 13, 2010

By Kanchibolta S. S, Brunton I, Tapia-Vergara F

The Split digital image processing system has been implemented in three Australian mines for analysing the size distribution of rocks from the images taken from muckpiles, conveyor belts and tipping trucks. This paper presents an overview of t

Jan 1, 1998

By Booth GW, Robertson IG

The Paddington Gold Mine ties within the Norseman-Wiluna greenstone belt, in the celebrated Eastern Goldfields province of the Yilgarn Block, Western Australia. Regionally, tropical to subtropical weathering has effected development of a prominent regolith and a deep lateritic profile. Detailed examination of the clay mineralogy, largely from a single drill hole which traversed the original Paddington I deposit, outlined three separate, vertically gradational assemblages, which are, in part, rock-type dependant. These include; 1. kaolinite with minur to trace quantities of sericite/illite (0-22m), 2. smectite and/or interstratified clay minerals, together with variable amounts of kaolinite, relic chlorite and illite/sericite (22-81m), and 3. chlorite and sericite (> 81m). Near surface, kaolinitic assemblages may be directly correlated with the intensity of lateritization, whereas smectite and interstratified clays from intermediate zones appear in association

Jan 1, 1989

`WELL HE WOULD, WOULDN'T HE?' Public Relations people have something in common with advertising people and politicians: there exists a perception that their whole Raison d'Etre is to create, mould, and maintain images which are far removed from reality

Jan 1, 1994

By T Angerer, N H. Maund, S Hagemann, D R. Cowan

Cliffs Natural Resources Pty Ltd - Asia Pacific Iron Ore's (formerly Portman Iron Ore Limited) K deposit (Dowd's Hill), at its Koolyanobbing operation in Western Australia, hosts enriched magnetite mineralisation below the presently mined haematite-goethite ore zone. Two distinct northwest-southeast elongated, highly magnetic anomalous bodies that dip to the north-east appear to be sourced by this deeper mineralisation. Magnetic modelling indicates significant remanent magnetisation with Qratios around 1.5, directed shallow down. The north-west anomaly is overlain by a ridge of uneconomic banded iron formation (BIF) and the present waste dump, whereas the south-east body was partly exposed during ongoing mining of overlying haematite-goethite ore. Sections of the magnetite mineralisation in this south-east anomaly were intersected previously by diamond drill holes. Review of the historic cores identified potential magnetite enrichment, with grades and mineralogy that might be amenable to beneficiation. A first-phase reverse circulation drilling program was designed to further delineate the trend and extent of the two anomalies. The following magnetite mineralisation assemblages are recognised from cores, reverse circulation (RC) drill cuttings and pit mapping of the south-east magnetic body: higher-grade magnetite-haematite ¦ goethite and magnetite ¦ pyrite and lower-grade, recrystallised magnetite-quartz (BIF), magnetite-carbonate, magnetite-talc and minor magnetite-bearing mafic schist. Disseminated specularite is locally present in theassemblages. Talc-schist and massive pyrite occur along the footwall contact. Magnetic susceptibility measured from drill chips within the magnetite-enriched zones reveals an apparent susceptibility values range of 0.2 to 1.3 SI. Preliminary results from Satmagan and Davis tube recovery analysis shows that the magnetite content in these mineralised zones correlate well with existing geophysical data and magnetic susceptibility measurements.

Jan 1, 2009

By J Young, S Yu, P Moyo, M Powell, A Musunuri, B Bonfils, S Kanchibotla, P Yaroshak, V Jokovic

The appropriate design of liners continues to be an issue on many mills worldwide. Loss of milling capacity especially at liner change, uneven wear lives along the mill, substantial scrap on worn liners, excess mill down-time, undesirably short and unreliable wear lives are all common issues. This paper presents a designed approach to liner optimisation that follows a logical path of initial design and step-wise improvements based on liner wear monitoring. The target is to have a good liner design from start-up, then tune the profiles, heights and thicknesses based on wear monitoring. This is conducted as a team of liner specialist, site personnel and liner supplier. The application to the Pustynnoye SAG mill of JSC Altynalmas in Kazakhstan is presented. The increase in liner life by around 50% along with increased mill throughput of over 20% illustrate the huge benefit of the cooperative triumvirate approach through the gains that can be made in productivity and reduced liner costs.CITATION:Powell, M, Kanchibotla, S, Jokovic, V, Hilden, M, Bonfils, B, Musunuri, A, Moyo, P, Yu, S, Young, J, Yaroshak, P, Yalcin, E and Gorain, B, 2018. Advanced mine to mill application at the Barrick Cortez mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 177–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By G Nicholas, S Coward, J Vann, R Wolff, S Jackson, S Moayer, A Bye

"A new approach to mineral project evaluation is described called Scenario-Based Project Evaluation (SBPE). SBPE incorporates well established æscenario planningÆ and æscenario thinkingÆ approaches, which are used extensively in other industries,?most notably the?petroleum industry. While most scenario planning is qualitative and non-probabilistic, the approach described here includes both quantitative and qualitative aspects. SBPE is complementary to optimisation approaches and allows mining firms to build and operate projects that are more robust in the face of adverse changes as well as proactively respond and exploit the upside offered by a realistic assessment of variability. The approach has potential to improve project performance and decrease operational risk. It also has important applications for currently operating mines.Conventional evaluation of metalliferous mineral deposits uses estimates of metal grades and deleterious attributes in singular æorebody modelsÆ, usually 3D block models, which fail to capture two critical aspects that underpin the realised value of mining projects: the inherent uncertainty of the estimated attributes the spatial variability of attributes, at the scale of mining selection, which impact on downstream processing steps and fundamentally drive realised value. While singular models are appropriate for estimating block averages, conditional simulation (CS) models of the relevant attributes are needed to represent uncertainty and capture spatial variability. Any attributes that can be either built into CS models and/or modelled in the envisaged mining/processing steps, can be evaluated fully through to highly ægranularÆ (ie detailed and un-smoothed) cash flows. A complete view of SBPE relies on selected strategies being tested against plausible æscenariosÆ of factors external to the project and thus outside management control. æExternalitiesÆ captured in such scenarios include market prices, costs and taxes. Via SBPE, project managers may demonstrate that there is material value in preserving or purchasing options that provide future flexibility to respond to the changing externalities or changes in orebody performance. Such flexibility generally comes at a cost but is very difficult to value. It is argued that full value chain evaluation using SBPE can help to value these options for a mining company. A case study for a gold mine is presented.CITATION:Vann, J, Jackson, S, Bye, A, Coward, S, Moayer, S, Nicholas, G and Wolff, R, 2012. Scenario thinking - A powerful tool for strategic planning and evaluation of mining projects and operations, in Proceedings Project Evaluation 2012, pp 5-14 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 24, 2012

By D Guibal, J Vann, M Harley

Many sample value distributions are highly skewed and present variograms with high relative nugget effects and/or short-range structures. In consequence, significant deskewing of the histogram and variance reduction occurs when transforming between sample and block support, where blocks are of significantly larger volume than samples. When making estimates in the mining industry we usually wish to estimate on the basis of block support rather than sample support. The selective mining unit (SMU) refers to the minimum support upon which ore/waste allocation decisions can realistically and practically be made. The SMU is usually significantly smaller than the sampling grid dimensions, in particular at exploration/feasibility stages. In a non-linear estimate, for each large block (by convention called a æpanelÆ) we estimate the proportion of SMU-sized parcels above a cut-off grade threshold. A series of proportions above cut-off defines the SMU distribution. Use of such non-linear estimates reduces distortion of grade-tonnage curves and provides a better basis for mine planning and economic decision-making. At present, Multiple Indicator Kriging (MIK) is the most widely used technique for performing estimation of recoverable resources. MIK is not the only approach available and it has some potentially serious limitations. The MIK technique is described and a number of theoretical and practical implementation issues are examined. In particular: MIKÆs assumptions about spatial distribution of grade; the behaviour of indicator variograms; application of change of support models; order relationship problems; and modelling the tail of the distribution. Some simple tests are described which allow us to determine the suitability of different estimators for a given deposit and criteria to identify a preferred estimator are also examined. Uniform Conditioning (UC), an alternative estimator which may be used instead of MIK, is described.

Jan 1, 2000

By B J. Monaghan, R J. Longbottom, D J. Pinson, S J. Chew

Recycling steel plant by-products is a critical issue for achieving both environmental and economic sustainability of integrated steel plants. A key steel plant by-product stream is dust from basic oxygen steelmaking (BOS), which can be recycled back to the BOS vessel as iron units and to aid slag formation. The major limitations for its recycling are zinc and the uncertainty in zinc speciation of the dust. This uncertainty affects the amount of dust recycled and how it interacts with the slag during processing. BOS dust in stockpiles can undergo self-sintering reactions that oxidise the iron-bearing components. As this occurs, zinc (or oxide) may combine with iron oxides to form a zinc-iron spinel solid solution phase. Knowing which zinc-bearing species are present in the BOS dust is a key aspect in understanding and developing an efficient recycling process for the dust. To overcome difficulties associated with phase identification in the BOS dust (both fresh and selfsintered), particularly the magnetite-zinc ferrite spinel solid solution using X-ray diffraction (XRD) / scanning electron microscopy (SEM) / energy dispersive spectroscopy (EDS), high end characterisation tools, transmission electron microscopy (TEM) and Mössbauer spectroscopy, were also used. Such an approach allowed improved phase identification of key zinc- and iron-bearing phases that were not previously resolvable. The zinc in fresh BOS dust was mostly present as extremely fine separate particles of zinc oxide, attached to the iron particles. These extremely fine particles were <10 nm in size. Additionally, a small amount of zinc ferrite was also identified within the sample (most likely contained within a magnetite-zinc ferrite spinel solid solution). However, the zinc in the self-sintered BOS dust, was found to be present entirely in a magnetite-zinc ferrite spinel solid solution. While this spinel phase had been previously identified by XRD, it was not clear that it contained zinc. The Mössbauer results provided definitive evidence of zinc within the spinel phase.

Jun 19, 2024

By M Aros, L Reilly

Iron ore is normally sold in bulk at certain specifications. These include iron grade and specific contaminant grades, typically silica, alumina, phosphorous and sulfur. These target grades are normally agreed between the mining company (producer) and the steelmaking company (customer).This study presents an alternative to traditional cut-off grade calculation, using linear programming that maximises the total ore inventories within a predefined mining envelope while meeting the specified targets. Providing a feasible mining sequence that maintains the target grade is not covered in this study.The method was applied to Fortescue’s operations. The complexity arising from differing ore quality within each mining horizon, variable yields and upgrades and the need to control iron and contaminant grades provided a good opportunity to test an alternative method of ore selection. The new method significantly reduced the time spent in cut-off selection and sensitivity analysis, and provided an optimised solution.CITATION:Aros, M and Reilly, L, 2014. Ore selection optimisation for an iron ore deposit using linear programming, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 345–350 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Kepplinger W

The KR Process is a joint development by VOEST-ALPINE, Austria and its subsidiary company KORF ENGINEERING, Germany. This new technology allows production of hot metal on the basis of non-coking coal. The KR Process is based on the idea of separating the process steps realized in the blast furnace (generation of reduction gas, reduction of iron oxide and melting of the reduced iron) and including coking of coal. These reactions are carried out in two reactors: - the melter gasifier, where non- coking coal is coked and gasified into a high quality reduction gas and hot prereduced iron is melted. - the reduction furnace, where iron oxide is reduced by the reduction gas generated in the melter gasifier and discharged in a hot state. In order to prove the process a pilot plant has been set up in Kehl/ Rhine in 1981 with a nominal capacity of 60.000 tpy.

Jan 1, 1986

By A Giblett, B Putland

This paper provides a simple guiding framework for grinding circuit optimisation, focussing on common themes in past optimisation success stories, the conditions for success and techniques that can be employed to identify and define opportunities. Many significant grinding circuit improvements have been reported for operating plants, based on recurring themes such as the optimisation of mill feed size, mill liner design, process control, critical size, grinding media and classification. The paper condenses these experiences into a set of simple questions for the operator to ask, and provides guidance towards identifying and achieving the optimisation goals.CITATION:Giblett, A and Putland, B, 2018. The basics of grinding circuit optimisation, in Proceedings 14th AusIMM Mill Operators&#39; Conference 2018, pp 129–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By J Zhang, B Wei, T Zhao, K Wang

Understanding mining-induced surface movement and fissures is critical for environmental protection and geological prevention. In this study, image recognition algorithms, satellite remote sensing and unmanned aerial vehicle photogrammetry (UAVP) were combined to identify surface movement and fissures caused by mining, and a case study was conducted in a coalmine in western China, and the following conclusions were obtained.

Sep 1, 2024

By R A. Pax, B Cornish

"Although it is well known and easily experienced that the feed size distribution influences the throughput and stability of operation of a semi-autogenous grinding (SAG) mill, the details are poorly understood since it is often only the input and output measurements that are used to identify unfavourable in-mill conditions. Load cells and power monitoring are sometimes used but are generally poor indicators of the mechanisms that lead to such unwanted conditions.At the MMG Century operation a 12-microphone array around the SAG mill using non-contact acoustic measurement methodology has been used to diagnose the in-mill conditions to facilitate improved throughput and stability of operation. Use of acoustic measurement and control has provided a demonstrated increased throughput of at least 20 per cent as well as improved stabilisation of the mill. Since the information derived from the acoustic noise from a mill allows discrimination of the behaviour of the steel balls and the rock, a number of in-mill conditions can be identified with signals that include toe and shoulder angles, water holdup and the ball to rock ratio.Feed size variations, measured online with an imaging system, have been used to determine their effect on the internal charge behaviour. It has been found that circumferential segregation of steel balls and rock occurs as well as poor mixing of large rocks. Both of these effects are not conducive to optimal breakage rates of different size fractions. Longitudinal segregation effects also occur. This paper presents and discusses these results and illustrates how the new acoustic knowledge can be used to manage and improve mill operation and stability.Citation:Pax, R and Cornish, B, 2016. Understanding Size Effects of Semi-autogenous Grinding (SAG) Mill Operation as a Pathway to Solving Feed Disturbances - Case Study using the MMG Century SAG Mill, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 321&ndash;330 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016