Search Documents

By Mercer J. K

Shaft guide reaetions in No. 2 Ore Shaft, Mount Isa Mines Limited, have been reduced to a low order of magnitude by the use of self aligning slippers and spring loaded guide rollers. Before commissioning the new 4500 h.p. winder at No. 2 Ore Shaft in January, 1958, it was realised that the increase in hoisting speed from 1800 to 2650 ft/min. would cause high shaft guide reactions which would be increased further when the elongated 12 ton skips replaced the existing 7 ton skips.The Cambridge accelerometer was used to measure the shaft guide reactions and to confirm that progressive skip modifications were resulting in reduced reactions. The skip modifications were completed in 4 weeks.INTRODUCTIONIn 1956 an expansion programme was initiated to increase production from 5000 to 11000 tons per mining day. At No. 2 Ore Shaft the 1500 h.p. winder operated at 1800 ft./min. and hoisted a 7 ton capacity skip. The new 4500 h.p. winder operates at 2650 ft./min. and hoists a 12 ton capacity skip. No. 2 Ore shaft is equipped with two 5 ft. by 5 ft. hoisting compartments (Fig. 1) and any increase in skip capacity meant an abnormally long skip. This feature, coupled with the increase in hoisting speed, could have caused very high shaft guide reactions. Before commissioning the 4500 h.p. winder, a Cambridge accelerometer was borrowed from the University of Adelaide and was used to measure the shaft guide reactions. Rather than carry out an extensive shaft timbering programme, the skips were modified by fitting cushioned guide shoes and spring loaded guide rollers (Fig. 1). Testing commenced in February, 1958, and was completed in March, 1958.

Jan 1, 1961

By A F. Cooper

The northeast-southwest trending ~25 km2 area incorporating Bald Hill is located 18 km northeast of Haast, and 5 - 7 km west of the Alpine Fault in South Westland, New Zealand. The geology consists of Greenland Group greywacke overlain by a Cretaceous-Tertiary sedimentary sequence and fluvio-glacial/marine terrace deposits of Quaternary age. Alluvial gold in Cole Creek, draining west from the summit of Bald Hill, may be derived either from vein mineralisation in basement rocks or from fluvial or marine terraces.   This paper focuses on the potential for in situ gold and base-metal mineralisation in sporadic, siderite-rich quartz veins that cut basement greenschist facies metasediments that have been overprinted by contact metamorphism.   Throughout the area, vein compositions are dominated by quartz and commonly feature zoned plagioclase. Alteration adjacent to veining within the contact aureole is dominated by 1 - 2 mm, coarse grained biotite, with small amounts of sulphide, and is pervaded by abundant siderite veinlets. Outside the aureole, wall rock alteration to veins consists of fine grained chlorite. Trace element XRF analysis has been used to ascertain base metal concentrations within samples of vein and alteration zones collected from throughout the area. Vein and alteration zone mineral assemblages containing <5 per cent sulphide, with low concentrations of As, Cu, Pb and Zn indicate low potential for gold and base-metal mineralisation in the Bald Hill region. Contact metamorphism of Greenland Group basement in the northeast of the region, is likely due to emplacement of a poorly exposed Cr- and Ni- enriched gabbro. The presence of biotite and andalusite in hornfelses indicate contact metamorphism occurred at temperatures >350¦C and at depths <10 km. Widespread vein distribution does not appear to be related to contact metamorphism or gabbro emplacement. Further research is required in order to establish the fluid source from which the veins were precipitated.

Jan 1, 2007

Naturally occurring rutile contains approximately 96 per cent titanium dioxide (Ti02), whereas the product from the ilmenite reduction - aeration upgrading process, "sub- rutile", contains only about 92 per cent Ti02. Therefore, there is an-incentive to lift the quality of sub-rutile by removing transition metal impurities, in order to supply a more valuable and marketable product, particularly for the chloride-route pigment producers. Previous studies have shown that the sub- rutile residual iron content (of approximately 4 per cent) and residual manganese content (of approximately 1.5 per cent) are chemically bound within the titanium-oxygen mineral lattice, and are most difficult to remove by simple leaching methods. In attempts to improve their eventual removal, a simple process modification has been successfully investigated in laboratory scale trials. Transition metal sulphides have been formed in the reduced ilmenite by using a "sulphur-doping" technique during reduction (metallization) conducted at controlled temperatures. These compounds give rise to greatly enhanced dissolution of the unwanted transition metal constituents during the sub- sequent aeration and acid washing steps. Thus, the manganese content of the final sulphur- doped, reduced-aerated, acid washed product can be reduced by about 90 per cent to 0.2 per cent, and the iron content by about 70 per cent to less than 1.5 per cent, in comparison with those levels remaining after unmodified pro- cessing. Additions of sulphur as low as 2 per cent of the weight of the ilmenite have proven satisfactory. Preliminary studies reveal that the modified process is economically feasible. These results suggest that the sulphur content of the Collie coal char used in an unmodified reduction step must exert some influence on the eventual removal of iron and manganese during aeration and acid washing.

Jan 1, 1973

By N Armitage, C Young

In the dynamic realm of mining health and safety, addressing psychosocial hazards is crucial. Legislative requirements now demand employers navigate this complex terrain, but uncertainty often clouds effective management. The resource industry’s skills in managing physical hazards are showcased in their adaptability in this case study. Integrating the Critical Risk Management framework with organisational psychology, a mining company achieved a transformative breakthrough. They identified and assessed psychosocial hazards and established a sustained and risk based approach to managing these hazards within the workplace. This innovative approach encompasses strategic steps. Key learning from the case study was: - Beyond Bow-tie Analysis: Discover why a linear risk analysis tool, like Bow-tie Analysis, falls short in capturing the dynamic and interdependent nature of psychosocial hazards. - Psychological Safety Power: Learn why psychological safety is vital for gathering accurate data and ensuring control effectiveness. - Dive into how it creates a data-driven foundation for success. - Broadening the Brush: Explore the impact of preloading Broad Brush Risk Assessments, an educational and dynamic hazard-identification tool. Control Mastery: Gain insights into how the Critical Risk Management framework ensures ongoing control monitoring and effectiveness for psychosocial hazards. While this implementation’s outcomes are still in their early phases, promising key indicators such as absenteeism, turnover and cultural engagement have emerged. These metrics are set to experience positive shifts as controls prove adequate. As the conference nears, we anticipate having data to showcase these transformative results. Join us in this illuminating presentation as we journey toward a safer, more psychologically resilient workplace.

Apr 16, 2024

Declining from surface provides access, haulageway, ventilation and provision for ser- vices for stoping and development. Three boom jumbos and 3.8 m3 capacity diesel loaders are used in decline development, the majority of which is driven at a gradient of 1 in 9. Primary ventilation is drawn from the mine through raisebored airways and high pressure contra rotating fans provide secondary ventil- ation. To meet schedules a special decline crew was formed on similar lines to a mining con- tractor. The basis of payment for the mining party was changed and the net effect was to accelerate development. Ground conditions demand constant support and this is achieved with chemical anchor rock bolts, multistrand grouted bolts and shotcrete. Major local shear zones are encountered and when they are to be driven through, a combina- tion of the above methods, involving a spiling technique, is used.

Jan 1, 1977

By R Berthelsen

The Peak Gold Mines Pty Ltd (PGM) operations are located approximately 9 km south of Cobar, NSW. PGM currently mines and treats ore from three separate orebodies within 5 km of the original plant. Production from the original Peak orebody ceased in April 2002, with ore currently sourced from underground at New Occidental and Perseverance, while New Cobar supplies ore from an open cut mine. In March 2003, Wheaton Minerals Asia Pacific purchased the operation from Rio Tinto who operated the mine for around ten years. The Perseverance deposit is situated between 600 and 1000 m south of the Peak orebody. Access is via shaft from Peak to 630 m below surface and then by decline to the northern end of the deposit locally known as Zone A. Development of the resource commenced mid 2002 to set up for a long hole open stoping operation at 25 m level spacing. The first production stope was successfully brought on line December 2003. The Perseverance deposit is hosted by sediments and volcanics along the eastern margin of the Devonian Cobar basin and is one of many deposits with the Cobar Gold Field. The Cobar Gold Field has produced approximately 2.5 million ounces of gold since 1880. The Perseverance area had long been considered prospective due to the presence of old workings at the southern extensions of Peak line of lode. Significant mineralisation was first discovered at Perseverance in 1994 when PGM drilled a hole targeted 950 m below the historic workings. The target was based on an apparent plunge to the stratigraphic controls to the Peak Orebody. Subsequent exploration within and around the ægreaterÆ Perseverance area has been significantly aided through the use of downhole electro-magnetic surveys due to the close spatial association between gold and sulfide mineralisation.

Jan 1, 2004

By A Morris

The Express Rail Link (XRL) will provide high-speed rail services from Hong Kong to Guangzhou and a connection to the national high-speed passenger rail network serving major cities throughout Mainland, China. The HK$ 67 B (NZ$ 11.5 Billion) project is of great strategic importance for Hong Kong and is being implemented to a very tight schedule, from early 2010 with completion targeted for 2015.The works include a 15 platform terminus station in West Kowloon, 26 km of twin track tunnels from the terminus to the Hong Kong/Shenzhen boundary at Mai Po, tunnel vent shafts/adits/emergency rescue siding and a stabling siding facility. Trains on the Hong Kong section are intended to operate at speed up to 200 km per hour and up to 350 km per hour on the Mainland section.This presentation will provide an overview of the entire XRL project, with a focus on the challenging geotechnical and spatial constraints on the tunnel works. This is an abstract only. No paper was prepared for this abstract.

Mar 8, 2011

Taxation is a major factor in evaluating mining project developments. The availability or otherwise of effective tax relief for project expenditures can have a crucial bearing on the decision to proceed with a project. The special position of the mining industry is recognised within the Income Tax Assessment Act (the "Tax Act") by special legislation, namely Divisions 10, 1OAAA and 10AA. The legislation both extends the scope of items which are eligible for deduction and affects the timing of deductions. Generally, the legislation separates expenditure into 3 categories: 1. Expenditure on exploration 2. Capital expenditure on the development and the running of the mine; and 3. Facilities used in the transport of minerals. Companies evaluating a project should carefully analyse their proposed expenditures, allocating them between these categories so as to identify potentially non-deductible expenditures and to determine the period over which tax relief will be Obtained.

Jan 1, 1983

A flow sheet has been developed to treat a high tonnage highly preg-robbing gold ore. The ore is low grade and fine grained with a high proportion of very fi ne free gold. The key components of the flow sheet include gravity, flotation, intensive cyanidation with direct electrowinning, and carbon-in-leach of the flotation concentrate. The circuit produces a low overall mass pull to concentrate allowing economic intensive treatment of large tonnage low-grade material. Efficient recovery of fine gravity gold using a Falcon concentrator in both the milling and flotation circuits, and subsequent intensive cyanidation in a Gekko InLine Leach Reactor (ILR) is critical to the process with over 70 per cent gold recovery expected in this circuit. Grind size control was also found to be important in controlling the activity of the preg-robbers in the carbon in leach circuit and also in the solid liquid separation performance. Tests at the large-scale demonstration plant have been conducted to demonstrate the effectiveness of this flow sheet. A large low-grade deposit is currently under development with the aim of developing a 10 Mt/a treatment plant with the subsequent addition of equivalent sized process lines in multiples of 10 Mt/a. The economic development of this orebody is critically dependant on understanding and exploiting the properties of the ore. In particular it is critical to minimise the effect of preg-robbers by recovering free gold with Falcon concentrators and InLine Leach Reactors. Recovery of the remaining gold by flotation into a small mass yield allows this fraction of gold to be treated by CIL leaching utilising high carbon levels. It is critical is to ensure operation at the optimal grind size to maximise liberation of the free gold and minimise pregrobber activity. The ore has been identified as preg-robbing with low recoveries obtained if treated using conventional cyanidation and carbon absorption. The mineralogy consists of predominantly fi ne grained free gold with minor sulfides including pyrite and arsenopyrite. With conventional cyanide leaching in the absence of carbon, gold recovery is less than 50 per cent. Direct cyanide leaching of the ore in the presence of activated carbon results in an improved but still uneconomic gold recovery. The gravity recoverable gold (GRG - as defined by Andre La Plante) content of the ore has been measured to be 70 per cent to 85 per cent in various tests with liberation grind size of approximately 106 ¦m. This indicates gold is predominantly free and suitable for recovery by batch centrifugal concentrators into a low mass yield. This property of the ore presents the opportunity to maximise the recovery of gold by separating it from the majority of the preg-robbers prior to leaching. Due to the very fine gold particle sizes and the necessity to maximise recovery of this fine fraction Falcon concentrators were selected for the duty, with their proven high recoveries at very fine gold sizes. The gravity recovery in the milling circuit is designed to be in the range 55 to 65 per cent. This has been achieved in the existing pilot plant using a Falcon operating on ball mill discharge within the mill recirculating load. Intensive leaching in an InLine Leach Reactor is essential to recover the gold from the gravity concentrates. Tabling is not a preferred option since recovery is lower than intensive cyanidation and any gold losses to table tails will report to CIL where recovery is reduced by the presence of preg-robbers. Furthermore, tabling recovery from the gravity concentrates is particularly poor due to the fine particle size of the free gold. ILR recoveries of 98 per cent were demonstrated in the pilot plant using an ILR100BA and leach conditions were investigated in the lab using pilot plant generated Falcon concentrate. Recovery of gold from the pregnant solution was achieved with direct electrowinning at pilot and efficiency and sizing parameters were determined at lab scale. To further increase free gold recovery Falcon concentrators will be installed in the flotation circuit. Location of the Falcons in the circuit is not finalised but installation on the rougher concentrate stream is favoured since it will allow multiple pass recovery. This is expected to recovery a further ten to 20 per cent of the gold, as indicated by lab tests on pilot plant generated material. The gravity concentrate from the flotation circuit will also be leached using InLine Leach Reactors. Initial intensive cyanidation tests carried out on lab generated flotation concentrates indicated higher recoveries than CIL can be obtained even though the concentrates contain significant levels of preg-robbing material. This can be explained by the high cyanide, high pH leaching conditions used in the ILR which alters the absorption equilibrium of the preg-robbers. Further optimisation of the leach conditions will be undertaken once more concentrate becomes available. Recovery of the remaining gold content is achieved by flotation into a small mass yield, however the preg-robbers are also recovered into this concentrate. Due to the presence of the preg-robbers gold leaching must be carried out in the presence of high levels of activated carbon in a CIL system. The recovery has been shown to be strongly dependant on the carbon loading and the concentrate particle size. The carbon competes against the preg-robbers for dissolved gold while excessive grinding increases the surface area and activity of the preg-robbers. This has been demonstrated in test work however the economic optimum leaching conditions and carbon loading have yet to be determined. The grind size is critical to the economics of the project, not only due to its effect on gold recovery but also due to its effect on the major operating and capital costs at both the front and back end of the process. It is critical to grind enough to obtain both gravity free gold and flotation liberation at low mass yields however over-grinding results in large increases in mill size and power at the front end and filtration or thickening costs at the tails. Because these unit operations treat essentially all the plant feed even small changes can result in major impacts on project economics. The viability of this project is greatly enhanced by the high recovery of gold into a small mass yield. In particular the production and intensive leaching of the free gold gravity concentrates will allow over 70 per cent of the gold to be recovered efficiently with minimal impact from preg-robbers. By using flotation the mass of the remaining fine preg-robber contaminated material, to be leached in CIL, is greatly reduced allowing this difficult material to be economically treated. This is an ABSTRACT ONLY. No paper was prepared for this presentation. 

Aug 1, 2010

By M S. Tuohy

Poorly judged or under-appreciated change plays a role in many major accidents. In particular, operational changes related to continuous improvement, maintenance and introduction of new technology can lead to unintended safety (and other) consequences. This paper provides an overview of the role of management of change in preventing unwanted impacts on safety, community relationships and the environment. It draws on a range of incidents covering mining, minerals processing, refining and smelting where inadequately assessed or ineffectively implemented change led to significant safety, environmental or community consequences. The paper will also highlight cases of well-managed complex change and the underlying model of decision-making in place to make those decisions. All these examples are drawn from Atturra’s experience in response to accidents or working with sites to improve their management systems. The paper will report on the challenges of applying conventional risk assessment approaches to complex or technically significant change. These typically result in either onerous and lengthy change procedures that are prone to workarounds or poor implementation. Conversely, ‘light touch’ or efficiency driven change processes present the risk of intended consequences by failing to bring appropriate expertise to bear in decision-making. Such balances can be resolved by considering the designation of ‘technical authority’ with appropriate expertise to consider the change and deconflict any production, cost or schedule trade-offs. Finally, the paper will reflect on the key components of management of change systems in the context of major accidents, highlighting good practice in how they are implemented. This will consider the integration of existing corporate processes, risk management and organisational structures into management of change systems, not just the content of change forms and procedures.

Apr 16, 2024

QEMSCAN« technology is a widely accepted automated e-beam technique providing quantitative and statistically robust mineralogical data to the mining industry. It uses X-ray mapping combined with backscattered electron (BSE) brightness to identify minerals in almost any type of geological material (Gottlieb et al, 2000). Besides the modal mineralogy also the liberation, associations, average grain size and other textural information can be obtained. The aim of this study is to test reproducibility of this technique by setting up and running standard tests on different QEMSCAN« systems. Multiple sample blocks were prepared by our standard operating procedure as epoxy-mounted, carbon-coated, polished blocks. The replicates were measured under the same conditions and measurement parameter settings on different QEMSCAN« instruments. The relative standard deviation (RSD) for the set of measurements was calculated. Generally the reproducibility of the systems themselves was found to be excellent, ranging between 0.4 and 1.5 per cent RSD. The more significant change in the reproducibility was found to be caused potentially by the sample preparation and variation in the mineralogy of the replicates. The measurement parameter settings together with these variations can account for almost 15 per cent RSD for minerals of low abundance. For analysed samples good results for the main phases present in quantities higher than 2 - 5 wt per cent of the total mass of the sample were confirmed with RSD generally below six per cent. Following the experiments, the parameters having the biggest influence on the performance of the QEMSCAN« and its precision are discussed in detail. The importance of sample preparation procedures and measurement parameter settings is emphasised. It is shown that experience and excellence is necessary for getting the most from the automatic mineralogical methods like QEMSCAN«.

Jan 1, 2008

The use of scrapers in mining and earthmoving operations is not new; in fact they are one of the earliest methods of bulk earthmoving. A single machine, which can load, haul, and dump material with a minimum of ancillary support is a highly productive and cost-efficient method of earthmoving. In recent times scrapers have been unpopular due to perceived problems and operational limitations, but the last couple of years have seen a resurgence in the use of scrapers in the Bowen Basin as a primary prestripping tool. The main operational limitation of scrapers is the economic operating range. Maximum productivity and lowest cost per bcm is achieved on short leads, as the lead distance increases the cost per bcm quickly reaches and then overtakes that of an truck-excavator fleet. The geometry of a ætraditionalÆ coal mine does not readily allow short leads for prestrip fleets due to the nature of dragline stripping operations. The strip arrangement means that material has to be taken around the end of the pit, meaning a longer haul distance than the actual point-to-point distance between load and dump. This can be alleviated by using pit bridges, however these can cause spoil problems for draglines if not properly planned and have been avoided by many mines. Due to the economic haul distance limitation of scrapers, truck-excavator fleets have become the normal method utilised. Currently more geologically complex mines are opening up, which do not allow traditional down-dip strip mining to occur. Cross-dip mining methods allow for short leads between prestrip loading and dumping areas, hence scrapers and bulk doze are realistic alternatives to a truck-excavator fleet in the prestrip environment. Keeping the lead distance to a minimum a fleet of 657Æs can move material at a very low cost. The other main operational limitation of scrapers is the type of material that can be economically excavated. Hard material can lead to damage to the bowl, free-flowing sand will not readily stay in the bowl leading to reduced load factors. Ripping the material with a dozer prior to excavating can lead to improved loading time, and greatly reduced GET consumption. When considering scrapers for prestrip operations a number of things must be considered: is the lead distance within the economic haul distance? should twin power (push-pull) or single power (dozer pushed) scrapers be used? do I need to rip, what should I rip with? what ancillary support is required? is there another system already available on-site which is currently under utilised? This paper considers the parameters under which large twin power scrapers are the most effective way of undertaking prestrip operations.

Jan 1, 2003

By S Gray

Based on the 2021 Volume 5 State of PlayTM mining survey of key executives and board members in the mining sector, the key responses to ‘Which of the following technologies will have the biggest impact on mining in the next 15 years?’, were ‘Sensing and Data’ followed by ‘AI and Analytics’. From the early 1970s it would have been unlikely to predict the level of sensing and automation introduced to the broad industrial sector. No better example is the automobile industry where the combination of technological advances and external drivers (such as emissions control) have driven an incredible rate of change. The introduction of sensing, data, AI, and automation in the mining industry is just ramping up. Until now our energy efficiency, environmental footprint, labour shortage, skills, and safety have not been challenged by stakeholders in the way we are seeing market forces develop today. In order to address these challenges, we need to look back to the automobile industry and learn their lessons to accelerate our application of digital capability, analysis, AI and automation This is critical, particularly as access to skilled human resources becomes more difficult. An example of how this can be achieved in a gold processing plant utilising the latest real-time sensing technologies is the ‘Carbon Scout’ developed by Curtin University, and OLGA developed by CSIRO, which are both online technologies, coupled together with Gekko’s ‘Neon’ digital platform to achieve a fully automated real-time gold processing system.

Aug 24, 2022

By Best R. J, Poulos H. G

The method for design of primary roof support for the large todoidal cavern constructed to house the Sydney Opera House parking station is presented. The cavern was constructed with 5 m of rock cover beneath Sydney's Royal Botanic Gardens. Design of rock reinfonnent using a combination of fully grouted rock dowels and Macalloy bars was based on control of horizontal shear movement along bedding features in the roof. A combination of linear arch type analyses and non-linear jointed finite element analyses were used in the design study together with an analysis of the shear resistance offered by fully grouted bolts under shear deformation.

Jan 1, 1993

The Jurassic Walloon Coal Measures crop out over much of the Moreton Basin and contain numerous thin, banded coal seams which have been mined at various locations since the 1870s. Historically most mining has been by underground methods. Increased exploration during the 1970s and 1980s has led to the delineation of significant open cut coal resources and to the development of the Oakleigh, Jeebropillly and Ebenezer open cut coal mines in the Rosewood-Walloon area. Over 2 170 million tonnes in-situ of shallow, high volatile bituminous coal with a mean maximum vitrinite reflectance of between 0.5 and 0.6 have been proven in the Basin.

Jan 1, 1991

By de Bruin J H

A method new to Australia was used for sinking a vertical shaft at Broken Hill in the development of Pasminco Southern Operations No 5 Ventilation Shaft. The 6 m diameter shaft of 820 m depth was planned with a construction method which allowed access for ground support as sinking proceeded by mechanical excavation.The vertical shaft boring machine, known as the V-Mole, was originally developed in West Germany. The machine operates in a manner similar to a full face TBM but vertically and the cuttings drop down a previously constructed raise. The raise is subject to stringent tolerance on verticality and must remain stable for the duration of reaming.

Jan 1, 1993

By Duncan GR

Having passed through a number of previous phases the best longwall results in Australia have shown a significant increase in the last two years. The results expected from a longwall face can be estimated from the ideal production rate, determined by the capacity of the equipment and the conditions in which it is installed, the utilisation, and the available operating hours. Back analysis of the results achieved suggests that, on average, recent improvements arise from the higher capacity equipment recently installed; the utilisation has in fact reduced slightly. Review of the constraints which limit the longwall results, i.e. shearer speed, AFC capacity, support, advance rate, and man travel speed, shows that little improvement can be expected in the ideal production rate in thinner seams. In thicker seams the AFC often proves the overriding constraint and further increase in equipment size could lead to increased future ideal production rates and is expected. In all cases a concerted effort to increase the utilisation achieved is likely. For deep mines with thin to medium seams this offers the most viable path to improvement; by contrast thick seams with highwall/shallow access may benefit from further increase in equipment size.

Jan 1, 1988

By Bonsall EM, Schwabe MR, Hamlyn DA

Historically, most of the gold produced from Kalgoorlie has been derived from the gold and gold telluride Golden Mile lode systems dominantly hosted within the Golden Mile Doler-ite and to a lesser extent, Paringa Basalt. In more recent times the gold-quartz stockwork ore bodies within Unit 8 of the Golden Mile Dolerite at Mt Charlotte have become increasingly imp-ortant.Extensive low grade gold mineralisation has now been defined to the north and east of Kalgoorlie within rock units of the Golden Mile sequence not generally considered to be highly prospective.Two main types of mineralisation have been defined. The first comprises variably mineralised and altered quartz-albite porphyr-ies emplaced within talc-carbonated Hannans Lake Serpentinite (Mystery deposit). There is intense fuchsitic, pyritic and carbonate alter-ation of the serpentinite adjacent to the porphyry bodies. Gold mineralisation is assoc-iated with fine-grained disseminations and veinlets of pyrite and narrow quartz and quartz-tourmaline veining within the porphyry and adjacent fuchsite-carbonate rock. Several sets of vein directions are present, some of which typically exhibit sulphide alteration haloesnnA H] rhina_

Jan 1, 1984

By Zervoudis J

Limitations of current touch-up solders for galvanised steel include coating thickness control problems and poor corrosion and abrasion resistance as well as health and environmental concerns due to toxic constituents such as lead. This paper reports on progress in ILZRO-sponsored research to develop an improved touch-up solder. Encouraging results were achieved in torch soldering trials with experimental zinc-tin-based alloys. Mouldability and coating thickness control were achieved over a practical working temperature range in which the solders consisted of a viscous mixture of solid primary zinc phase particles in a liquid zinc-tin eutectic matrix. The mouldability was dependent on the microstructure of the solder sticks, and optimum structures could be obtained through control of casting solidification rates and by the addition of small amounts of copper. Hardness, abrasion resistance, adhesion and corrosion tests on experimental Zn- (40 - 50 per cent) Sn-I per cent Cu also showed improved performance over lead-tin-zinc solders and compared the effects of tin content within this range. Atmospheric corrosion testing and optimisation of alloy composition and methods of solder stick production are continuing.

Jan 1, 1993

The exploration and mining risks are investigated and compared to the risks of smelting, secondary processing and other normal industrial activities. This study concentrates on the risk before, or at the investment decision. Internal and external risks are distinguished. Internal risks are the risks inherent in every engineering design and common to all projects. The main external risks are the financial risk, changes in prices, location problems and geological factors. Financial risks concern every capital-intensive and export-oriented project and cannot be considered as typical mining risks. Changes in prices, i.e. the market risk, concern every industry using raw materials, but the market risk is especially accentuated in the mining industry. Problems of location and infrastructure are normally more significant in mining than in other projects, and geological risks are unique to mining. All these risks associated with mining projects combine to form a risk at least twice as high as that for other normal industrial activities. Within the range of profitability of mines, which on average is the same as in the manufacturing industry, only a few highly profitable mines exist. These few mines are the sole reward for the high risks taken.

Jan 1, 1986