Search Documents

IT is intended in this paper to present in broad outline to the members of the Institute a short account of the conditions and operations that constitute what is, variously known as Subterranean Warfare, Military Mining, or Tunnelling. Realizing ,the magnitude of the operations, and the varied and minute details met with in them on,the Western Front, it is the writer's intention to confine these notes to operations carried out by the First Australian Tunnelling Company. In so doing there is no wish to detract from the very fine records of the Second and Third companies it is to be hoped that members of the Institute (or others) who were with these companies will write accounts of their doings-the former in the water-logged areas to the south of Armentieres, and later in the sand-dunes at Lombardzee, and the latter in the chalk area of the Lens coal...

Jan 1, 1920

The Western New South Wales Electric Power Proprietary Limited is the central generating authority for distribution of power to the majority of the Broken Hill mining companies and the Broken Hill Water Board. This station supplies the whole of the power to North Broken Hill Ltd and Broken Hill South Ltd. It also supplies, power to the Southern Power Corporation for distribution to the Zinc Corporation Ltd. The Southern Power Corporation has a generating station which is tied in with the central generating authority.

Jan 1, 1957

WINDING engines are one of the most important units in the equipment of a mine. Upon the winding machinery depends not only the output of the mine, but it supplies in most cases the only means by which workmen enter and return from the mine, and consequently the utmost care and attention is desirable in its design. The efficiency of a direct acting winding engine, as a machine is very low. In other words, the proportion between the useful work performed and the actual work the engine is capable of performing (under the most favourable conditions) is very small. The reasons for this are:-1. The intermittent nature of the work; the engine is stopped from 20 to 25 %(or even more) of the time which would constitute a useful day's work.2. The large amount of power that is absorbed applying the brakes to bring the load to rest.3. That the net useful load raised is small in comparison with dead load to be lifted, and the parts to be set in motion.4. That, owing to the frequent stops, initial condensation in the cylinders is always greater than in a continuously running engine, whilst radiation from steam pipes, valve chests, &c., goes on whether the engine is running or...

Jan 1, 1911

By P Dare-Bryan

Many mines have an interest in improving fragmentation at their sublevel caving operations in order to produce better ore recovery, lower dilution and less overbreak. The primary requirement for the extraction phase is to understand and optimise the flow of the fragmented rock in the rings including interactions with the caved material. Rock fragment formation is critically controlled by the blasting phase and can potentially be improved by optimising the dynamic energy distribution throughout the ring through the crafting of explosive charging, priming position and initiation timing. The modelling of fragmentation and damage due to explosive loading of complete rings is inherently and irrevocably a three dimensional problem that is difficult to address. We have therefore initially utilised an analytical code to predict vector peak particle velocities and energies that are restricted to the plane of a ring. Dynamic energy distributions based on common timing and priming practice have been compared with other possibilities using conventional pyrotechnic detonators as well as initiation designs based on accurate electronic detonators. The energy distribution can be quite subtly tailored to increase energy in appropriate regions or to decrease energy in the brow region for example to potentially reduce instability and the probability of misfires. We have also recently developed the capability to efficiently model particle flow using four-sided polygonal elements. Despite the 2D limitations of such a model this results in more realistic fragment interaction and stacking than can be achieved using conventional rigid circular elements. Modelling of a typical sublevel caving ring utilising these elements activated by the correct dynamics offers considerable potential for understanding the influence of the blasting energetics and timing on the complex flow and extraction process.

Jan 1, 2005

By D Feng, G C. Lukey, J S. J, R R. Dagastine

An ongoing challenge in the coal industry is pyrite removal using the flotation method for fine particles. The use of a æseparation in frothÆ (SIF) technique to recover coarse particles of up to a few millimetres in size has presented a potential solution. However the commercial success of SIF is still limited due to the poor understanding of the separation mechanism. The particle floatability in SIF is determined by the constructive or destructive stresses resulting from the forces exerted by the particle on the bubble films. Hence, the surfactant properties and the mineral characteristics (eg hydrophobicity, shape, etc) are the key factors that control the interaction between the particle and froth. In the present work, the interaction forces between different particles (ie crushed glass, pyrite and coal) and a single air bubble are measured in a non-ionic surfactant solution (pentaethylene glycol mono n-dodecyl ether, C12E5) using an atomic force microscope (AFM). Experimental results show that the interaction is primarily dependent on the contact angle (ie the degree of hydrophobicity of the minerals). For crushed glass, the transition from repulsion to attraction was observed as the contact angle increased. As the concentration of C12E5 increased, the adhesion force was suppressed due to wrapping effect. For coal and pyrite with much higher hydrophobicity, long-range attraction was observed. The effect of shape factor was only visible at high surfactant coverage where sign of destabilisation became noticeable on the retracting force curve. These results provide a fundamental understanding of the direct interaction forces of a complex real system between an irregular particle of either crushed glass, pyrite or coal and a single air bubble. Theories developed for interpretation and modelling are thus far based upon the study of ideal systems of glass or polystyrene spheres and an air bubble and were incapable of explaining the interactions in complex real systems. The presented measurements were a first approach to the problem of real mineral-bubble interaction in flotation systems. Thus, the results can only best be interpreted semi-quantitatively.

Jan 1, 2005

By M Dorricott

This paper describes the design, construction and performance of sill pillars using cemented development mullock at the Crusader Gold Mine. The orebody is some 35 m - 60 m in length, 5 m - 8 m wide, dipping at 60¦ - 85¦ and plunging at about 40¦ to the north. It is accessed via a footwall decline. The ore occurs at the contact between basalt and ultramafic. This contact is characterised by shearing and alteration; and is prone to unraveling failure. The cut and fill mining method at Crusader extracts 25 m high ore blocks in four flat back lifts and one 8 m thick crown pillar. To enable full recovery of these high-grade crown pillars with minimal dilution, a 5 m thick sill pillar is constructed using cemented rock fill (CRF), after mining of the bottom two lifts in each block. Uncemented development mullock is used as rock fill (RF) for subsequent lifts. Development mullock and cement/water slurry is mixed underground to produce CRF. The fill is transported to the stope in LHDs and dumped on the floor. The sill pillar is advanced progressively, with compaction provided by the loader driving over the previously placed fill. Old jumbo rods are installed as shear pins along the flat dipping hangingwall to reduce the risk of rotational failure of the pillar. A fan of cable bolts is installed into the hangingwall to prevent unraveling failure in the sheared ground. Buffer blasting is used to minimise damage to the CRF sill pillar when the crown pillar below is extracted. At the time of writing, extraction of the crown pillar underneath the CRF has taken place at the 930 stope. The crown pillar was extracted successfully with dilution from the backfill and hangingwall minimised and 98 per cent of the gold recovered. This compares with pillars that were mined beneath uncemented backfill where only 70 per cent of the gold was recovered and where there was significant dilution from the backfill and from hangingwall failures. Where no CRF was placed, there were also numerous production delays caused by large rocks from the hangingwall blocking the stope brow.

Jan 1, 2002

By B Petrie, D J. MacKenzie

The Macraes mine is producing 175 000 ounces Au/year from a mesothermal deposit with total resource of at least five million ounces. The deposit is hosted in greenschist facies Otago Schist, a widespread Mesozoic metasedimentary sequence that forms the basement of the South Island of New Zealand. Mineralisation was controlled by a late metamorphic shear zone which had both brittle and ductile structures accompanying mineralisation. The shear zone dips shallowly (about 15¦), subparallel to the shallow-dipping regional foliation, and mineralization occurred during southwesterly-directed thrust motion. Mineralisation occurred under greenschist facies conditions (about 350¦C) during uplift of the Otago Schist in the late Jurassic. No syn- or late-metamorphic igneous bodies occur within the schist belt. The hosting shear zone is up to 120 m thick, and is traceable for more than 30 km along strike. The shear zone is truncated by an underlying low angle normal fault that juxtaposes mineralised lower greenschist facies rocks on to unmineralised upper greenschist facies rocks.

Jan 1, 2004

For several years, the Geology Department of the University of Canterbury has hosted a series of postgraduate projects in the field of coal studies, supported principally by the Ministry of Energy and to a lesser extent by private companies. These projects have involved mainly West Coast Coalfields, and my own studies have focussed on inorganic geochemical aspects of West Coast coals. Because of the large number of potentially important analyte elements in coal, and the wide diversity of coals occurring in the West Coast region, this project has required a substantial amount of work to be spent on sample collection, sample preparation, development of analytical methods, and actual analysis. Considerable problems must be faced at the sampling stage: Can sufficient information be obtained from whole-seam composites, or should seams be sampled in plies. Ply analysis is preferable, but results of proximate analyses are usually available for composites only. Where multi-seam drillhole samples become available (eg Greymouth Coalfield, where some holes yielded more than six sampled seams), the ply option involves a dramatic increase in the number of samples. I have attempted to strike a workable compromise between geographical coverage of coalfields, and detailed sampling of individual seams at each locality. In many cases, sample material has been used jointly with Jane Newman who has carried out petrographic studies.

Jan 1, 1985

The Hall-Hoult process is likely to be the dominant method of aluminium production for the remainder of the century. The characteristics of the operation of a modern smelter are described and attention drawn to their disabilities which are due chiefly to the small production capacity of individual cells.The principal components of the Hall-H6roult cell - the electrolyte, the anode and the cathode - are discussed in order to identify the problems of scale-up. The factors influencing current efficiency and energy consumption are analysed and lead to the conclusion that the greatest potential for energy saving lies in reducing the anode to cathode distance (ACD).The most promising direction for major change is in the application of a new titanium diboride - carbon composite for coating of the surface of the cathode carbon. It improves the wetting of the carbon by aluminium and should permit the use of sloping cathodes and anodes. The deep metal pad would thereby be eliminated and, in the absence of magnetic perturbations, the ACD could be substantially decreased.The construction and testing of a full-size "Low Energy Cell" is scheduled for early 1986 and is expected to reduce energy consumption in aluminium production by about 15%.

Jan 1, 1985

By Eggleton R. A

X-ray diffraction techniques are commonly used in the identification and quantification of fine-grained materials. A relationship exists between the size of crystals in a sample and the degree to which they diffract X-rays. The Scherrer equation relates the broadness of diffraction peaks to the size of crystals responsible for diffraction (Klug and Alexander, 1974). Relatively large crystals of the order of I - 10 ¦m strongly diffract X-rays; the diffractogram of such crystals exhibit narrow intense peaks. As the size of the crystals in a sample is reduced, diffraction peaks become broader and less intense. Crystals less than 10 nm generally exhibit broad, diffuse and low intensity peaks. Some material is so fine-grained and poorly-diffracting that X-ray patterns show very little information in a normal one-hour scan thereby necessitating very long acquisition times of up to 12 hours. The term poorly-diffracting material (PDM) was coined for such material found within the bauxite deposit of Weipa, northern Queensland (Tilley and Eggleton, 1994; 1996). Common regolith minerals such as hematite, goethite and layer silicate clays are quite commonly fine enough to possess a poorly-diffracting character. Noncrystalline and poorly crystalline Fe-Si-Al-oxyhydroxides such as allophane, opal, ferrihydrite and hisingerite, have either a nondiffracting (amorphous) or poorly-diffracting nature (Eggleton, 1987).

Jan 1, 1997

The Bau Goldfield lies in the southwestern corner of Sarawak in East Malaysia. Evidence of past mining in the form of open pits and adits can be found over an area of 250 sq kin, centred on the township of Bau. Chinese were mining gold in the district as early as 1820. The Bau Goldfield so far has produced approximately two million ounces of gold, from alluvial deposits and over 50 hard rock mines. The largest single producer was the Tai Parit mine (700 000 oz) which was operated by the Borneo Company from 1898 to 1921 and by a local Malaysian family from 1991 to early-1997. Over the past ten years, gold resources totalling around one nullion ounces have been delineated through systematic exploration using modern techniques, with the bulk of the resource hosted in two deposits (Jugan and Pejiru).Triassic to Jurassic andesitic volcanics and coeval intrusives are the oldest rocks that crop out in the Bau Goldfield. These igneous basement rocks are unconformably overlain by 500 m of late Jurassic, massive, micritic limestone which in turn is overlain by a 1500 in thick flysch sequence, composed mainly of shale. Basement rocks and limestone are exposed along the hinge of a ENE-striking anticline that passes through the Bau district (Bau Anticline). A NNE-striking belt of Miocene granodiorite porphyry stocks and dykes also passes through the Bau Goldfield. All of the known gold deposits lie within 5 km of this zone of intnisives, with a concentration of deposits at the intersection of the intrusive hell with the Rau Anticline.

Jan 1, 1997

By S L. Barbour

Measurement of the net percolation from the base of a cover system into the underlying waste material is a key component of a cover system monitoring program. The units of measure (ie a percentage of precipitation or rainfall) are simple to understand for all stakeholders, which increases the importance of obtaining representative net percolation values. In general, lysimeters are used to measure net percolation across the cover material-waste material interface; however, the design of lysimeters for cover system monitoring programs in the mining industry have typically not considered fundamental aspects of lysimeter design. Lysimeter design is typically thought of as being conceptually simple, when in reality the design, installation, and operation of lysimeters is often counter-intuitive, due to the complexities of flow through unsaturated soil systems. This paper puts forward a methodology for lysimeter design while also presenting the fundamental design variables that should be considered. Lysimeter design for differing climates, cover materials, and waste materials is discussed. Finally, the performance of lysimeter designs previously installed in the field at sites in Australia, Canada, and the United States are subjected to numerical modelling to determine whether net percolation is being measured properly.

Jan 1, 2003

Optimal drill and blast design is a process often neglected by many underground hard rock mines. This is even more important to the new mine where ring designs need to be implemented and refined in a short period of time. In today's environment where more and more mining is being carried out by contract specialists it is the co-operation between a principal and contractor, who are working towards a common goal, that achieves the highest quality end result. The development of drill and blast designs that cause minimal damage to the mine infrastructure is particularly important to Northparke's E26 Block Cave Mine, as it consists of a single extraction level which must survive intact for the life of the mine. The advanced undercut mining method implemented at Northparkes is fired in a sequence which protects the mine development from potentially damaging abutment stress. This paper details how blast designs will be optimised and sequenced to satisfy the conflicting objectives of maximum rock breakage inside the drill pattern and minimum rock damage outside the pattern.

Jan 1, 1995

By J Harmse

This paper deals with the modernisation of the brakes on an electrically coupled Blair multi-rope hoist and covers the removal of the old calliper brakes and hydraulic control system, and its replacement with brake discs, disc braking units and hydraulic control systems. The paper covers the braking requirements of the hoist, which is made up of two electrically coupled single-drum hoists, together with the theory behind the choice of brakes and control systems supplied. The paper also covers the project logistics that were required in order to install and commission the new brakes and control systems with the minimum disruption to production on the only rock hoist on a major production shaft. Items covered include the modifications to civil works, pre-installation of bearing lubrication systems, brake discs and hydraulics and the interfacing of the new hydraulic control system to the existing electric control system. It had to be designed to be compatible to a new electric drive and control system due for installation at the end of 2005.

Jan 1, 2005

The major greenhouse gas emissions from coal combustion are leading certain people to argue for uranium mining and nuclear power to meet these challenges. Although there is considerable rhetoric around promoting nuclear power as 'green' due to its relatively lower greenhouse intensity, a careful study of the data is required to properly underst and the sustainability of uranium mining and nuclear power and whether it can or should have a role in future energy supply scenarios. This paper presents detailed research and analysis on uranium mining, focusing on known economic resources, production, solid waste and water management, pollution issues as well as energy and greenhouse aspects. A particular focus will be on Australia and its operating and prospective uranium mines. Overall, the paper raises fundamental issues concerning the long-term sustainability of uranium mining and nuclear power and documents the greenhouse intensity of uranium production and the nuclear fuel chain.

Jun 1, 2010

By S Jeon, K Aikawa, M Ito, A Kusano, I Park, N Hiroyoshi

In mineral processing of complex sulfide ores containing copper (Cu), lead (Pb), and zinc (Zn), flotation has been commonly used. Typical Pb mineral in the ores is galena (PbS), while some types of the ores contain anglesite (PbSO4). This article reviews our recent studies on the effects of coexisting PbSO4 on the flotation of complex sulfide ores, and a method to suppress the floatability of sphalerite (ZnS) in the presence of PbSO4 was proposed. Comparison of flotation experiments for different types of model samples showed that PbSO4 makes the separation of Zn from Cu difficult; that is, for the model sample containing PbS without PbSO4, Zn could be separated from Cu, while when the model sample containing PbSO4, Zn was recovered together with Cu as froth. Solution analysis and thermodynamic calculation suggested that Pb2+ was released from PbSO4 and reacted with ZnS to form PbS, acting as an adsorption site for the flotation collector, xanthate. This would be the main reason for high floatability of ZnS in the presence of PbSO4. As a method to suppress ZnS floatability for the ores containing PbSO4, a pre-treatment of the ores to remove PbSO4 prior to flotation was proposed. The results of model experiments using mixture of ZnS and PbSO4 showed that ~97 per cent of PbSO4 was dissolved within 30 minutes of pretreatment using ethylenediaminetetraacetic acid (EDTA) as extractant, and thus ZnS floatability was markedly suppressed. Moreover, Pb2+ extracted from PbSO4 during the pre-treatment could be recovered as zero-valent Pb by the cementation using zero-valent Fe as a reductant. The details of ZnS flotation in the presence of PbSO4 and the effects of the pre-treatment are discussed based on the results of surface analysis like XPS.

Aug 24, 2022

By James CH

For drainage sediment to be used as a successful sampling medium in reconnaissance geochemical surveys, the length of any dispersion train from a typical target must be great enough for it to be detected by a widely spaced sampling pattern, and must also be homogeneous enough to avoid it being missed by the unfortunate selection of a random low value sample. Elements which occur in stream sediments in the form of discrete heavy minerals present two special problems in this regard. Since the element is concentrated into a few particles, the medium is extremely heterogeneous, which makes representative sampling impossible unless very large samples are taken, while the high specific gravity of such grains leads to their being concentrated in traps along the stream bed. Several ways of overcoming these difficulties have been suggested. Among these the "schlich" test, in which heavy material obtained by panning is taken for analysis is among the most popular. However, the results of the present study indicate that while this method improves the nature of the patterns obtained, they are still far from satisfactory. Alternative methods of sample preparation, including the taking of light material for analysis, appear to provide better answers to the problem. In the area studied this approach eliminated most of the "noise" associated with the data obtained by other methods, as well as giving an extended dispersion pattern.

Jan 1, 1986

In the new refinery, at the works of the Broken Hill Associated Smelters Proprietary Limited, situated at Port Pirie, South Australia, the refining routine is similar to that carried on in the old one in that bullion is progressively refined first for arsenic and antimony, then for copper and gold, then for silver, and finally for zinc. However, actual procedure differs in that each refining operation is now conducted continuously, whereas in the old refinery intermittent batch treatment was practised.The early experimental work was concerned solely with the development of the continuous desilverising process, which, in addition to continuous treatment, embraces the novel feature of conjugate solution formation with consequent production of a silver product relatively high in silver and low in lead.

Jan 1, 1932

By Andrews S. J

Century is a shale hosted zinc, lead, silver deposit developed within gently folded, Proterozoic Lawn Hill Formation shales and siltstones, approximately 250 kilometres north-northwest of Mount Isa, comprising 118 million tonnes of stratiform mineralisation, averaging 10.2 per cent ,,inc, 1.5 per cent lead and 36 grams per tonne silver. The deposit is largely overlain by Cambrian limestone and younger Proterozoic sedimentary rocks, outcropping at only two places. Small discordant lode lead-silver deposits formed the basis of relatively small scale mining activity in the area for almost 100 years, exploration tenement covering the deposit being granted to CRAE exactly 100 years after the first mining leases were pegged in the area in 1887.Stratiform mineralisation occurs within three distinct blocks, bounded by normal faults and the unconformity between Lawn Hill Formation and overlying Cambrian limestones. The Termite Range Fault, a major northwest trending, regional scale fault system occurs adjacent to the northeast deposit boundary, while the Magazine Hill Fault, possibly a component of the east trending Little Range Fault system, forms the southern boundary of the deposit.

Jan 1, 1993

The paper continues an account, begun in a previous paper, of experimental work carried out by the author whilst a member of the metallurgical staff at the Cockle Creek Works. The general method of the description of the plant and works practice adopted previously has been followed.The paper is a short account of the methods used in and the results of an investigation of the fume losses from the various parts of the plant.MEASUREMENT OF VOLUMETwo independent methods were used. The first depended on a number of pitot-tube measurements of velocity. These readings were taken in the stacks leading from the various furnaces at a considerable height above the ground so as to obtain as regular conditions as possible at the points where the readings were taken.Three openings were made in each stack and the pitot tube inserted into each opening in turn and readings taken at the centres of imaginary areas of equal size. The average velocity in the stack was thus obtained.After four tests had been made at the smelter stack, which removed the gases from all blast furnaces in use, the centre of velocity of the gases for each test was calculated and was found to be practically constant in position. The previous procedure was varied in subsequent tests on this stack by taking a succession of readings at the centre of velocity instead of at various points...

Jan 1, 1925