Search Documents

By Greaves J. N

The U.S. Department of Interior, Bureau of Mines, is investigating the treatment of refractory gold ores. Chlorination in the treatment of refractory gold ores is applicable in many low-grade gold operations. When usable, this treatment provides an economic means of consuming sulfides and deactivating disseminated organic carbon. Chlorination, however, is a pretreatment technique that requires the neutralization of the chlorine prior to leaching the ore with cyanide. Research by the Bureau has extended the present chlorination technology to allow for the recovery of gold without the use of cyanide and allow treatment of some ores presently deemed untreatable by gold operators using cyanidation or chlorination/cyanidation techniques. Chlorination without carbon of two carbonaceous ores extracted between 1 and 20 pct of the gold; however, carbon-in-chlorine (CICL) treatments resulted in about 90-pct recovery with a reduction in carbon loading. A statistical design campaign for stripping metallic gold from the carbon loaded in a chlorine environment demonstrated elutions exceeding 90 pct.

Jan 1, 1991

By S K. Michelic, N Preisser

For certain applications, steels have to feature a very distinct and well-defined level of cleanness in terms of the number and composition of non-metallic inclusions. Therefore, one crucial aspect of steelmaking is removing and controlling said non-metallic inclusions during the process. Particle removal during ladle refining comprises three stages, namely: 1. Flotation 2. Transport through the steel/slag interface 3. Dissolution of the particle in the slag. Only if all three stages are completed the particle can be considered as fully removed from the steel melt which, in turn, leads to the slag being one of the most influential parameters for inclusion removal and control. Depending on the composition of the particles and the slag, the dissolution can be controlled by different mechanisms. This study focuses on the diffusion-controlled dissolution of solid oxidic particles in slags. For this, a model of particle dissolution has been developed. For modelling diffusion, either the differential equation following Fick’s second law can be solved, or an analytical solution to this equation valid for stationary interfaces can be used. Both approaches allow for calculations of concentration profiles of the dissolving species in surrounding slag. From this, the mass flux can be derived, which finally leads to calculating the boundary layer velocity due to considerations of mass balance. In this work, both methods as well as results of dissolution experiments using High Temperature Confocal Scanning Laser Microscopy are compared. This research aims to provide a framework for diffusion-based dissolution modelling in further expanding the understanding of particle dissolution in secondary metallurgy.

Aug 21, 2024

By Dendyuk TV

The possible use of combined (flotation/magnetic separation and magnetic separation/flotation) technologies involving the new flotation reagent systems for upgrading the iron ore concentrates, low grade manganese products and beneficiation of graphite-bearing dusts from integrated iron-and-steel works has been shown. It has been found that the absence of magnetic flocculation phenomenon worsens the reverse cationic flotation of oxidised iron ore concentrates and direct flotation of low-grade manganese products which require the use of modifiers possessing the flocculating properties. The synergetic mixtures of polymers have been proposed to be used as modifiers, ie polyacrylamide (PAA) with carboxymethyl cellulose (CMC) and polyacrylamide with industrial lignosulphonates (LST)

Jan 1, 1993

By Blain CF

For all mineral resource-based companies, it is important to reach the right balance of investment between acquisition and exploration to allow the best chance of achieving long-term corporate goals. The Broken Hill Proprietary Company Limited (BHP) provides an excellent example of success from generative exploration and supports the belief that exploration can be justified, not only in terms of investment criteria, but also because it is essential to a company wishing to build a dynamic profitable growth path based on world-class deposits as cheaply as possible. BHP was incorporated in 1885 to mine a lead/zinc/silver discovery at Broken Hill. The Company has since gone through a steel development phase (1911-1965) and is now in a major phase of growth partly based on exploration success. This third phase was marked by decisions taken in the 1950's to search actively for mineral and energy resources above and beyond the requirements of the steel industry. The commercial successes of this period have been Bass Strait oil and gas, Groote Eylandt manganese, Deepdale iron ore, Gregory coal and Carnilya East nickel. In total at least 22 new resource discoveries have been made in the last 25 years, of which 11 have been developed and several are undergoing feasibility studies. A financial analysis shows that the real value of the returns seeded by discovery covers the real exploration cost many times over. Moreover, the major discoveries have had a spectacular impact on the growth and development of the Company. BHP's present exploration effort is directed towards geological targets which most frequently meet attractive financial criteria and also promote diversification from steel-related earnings.

Jan 1, 1986

By Jaracz K

At the operation of mine winders in deep shafts considerable oscillations of winding ropes may occur due to elasticity of both wind-ing and balance ropes. The amplitudes of longitudinal oscillations may reach + lm at relatively low frequencies, ranging from 0.5 to 2 c/s. These oscillations may be dangereus for the rope and produce several hazards to the winding installation as a whole. They may cause conside-rable instant accelerations on the pulley and dangerous tensions in ro-pe wires. The excessive acceleration may cause the uncontrolled rope slip on the pulley. Several methods of limitation of these accelera-tions were developed, some of them have been already in control system: of electric drive of the winder. The most simple ones are: a/ limita-tion of the rate of change of acceleration and retardation of the win-der /so called "jerk"/ and b/ the proper selection of regulators of the winder control system to get the optimal control. The trouble in solv-ing the problem of rope oscillations is that the dynamic system of the winder is a nonstationaryone owing to changing distance of conveyance from the pulley. Besides, the system is described by the equations with distributed parameters. The brief discussion of the theory and its practical aspects are enclosed as well.

Jan 1, 1985

The development of present methods of pillar extraction has evolved from the very earliest of hand mining operations which were limited in scope by venti- lation and transport considerations. Conservation and safety considerations also have led to the current shortwall operations with conventional equipment and powered supports. The shortwall methods have had significant effects on safety, costs, con- servation, flexibility, and other aspects of pillar extraction. The present stage falls short of the ideal but is some guide to prediction in what direction may lie the ideal methods for the future.

Jan 1, 1974

By Albano C, Antila A, Flykt B

A method for relating operating variables and dewatering parameters of Thunes disc filters in the LKAB pelletizing plant at Malmberget in Sweden, via empirical mathematical models is described. Near orthogonal experimental design was used, where all independentvariables were allowed to span over their domain of variation and pseudo-randomly distributed among the experiments. The dewatering parameters are dependent on many variables and instead of using a traditional mechanistic model, an empirical model based on multivariate data analysis was chosen. The way of expressing the relation is by regression coefficients obtained from partial least square regression (PLS). Two empirical models were generated. The models were validated using an extra set of 56 experiments. The dewatering parameters were related to the design variables with few experiments, and user-friendly response surface methodology was used to determine the optimal conditions.

Jan 1, 1989

By Olson H, Kincaid R

The marine portion of the Pacific Basin and Rim constitutes a significant part of the world's surface in which the mineral resources are virtually undeveloped. Indications of substantial resources have resulted in speculation and uncertainty with regard to their potential in the near term. The main issues are centered on the markets for the resource materials, the technology needs for their recovery, and the possible impacts of their development on the environment. While the governments of Japan, France, the Soviet Union, India, China, and Korea are financing new programs in deep ocean mining, the US is consolidating its early leadership by the continuation of NOAA's authority under the Deep Seabed Hard Mineral Resources Act and the Sea Grant Act, Interior's authority under the outer Continental Shelf Lands Act, and by the development of a new Marine Minerals Technology Center within the Department of Interior's mineral institutes program, managed by the U.S. Bureau of Mines. The Center has a Continental Shelf Division (CSD) located in Mississippi, and an Oceans Basin Division (OBD) located in Hawaii. Research and training in the divisions is directed toward the practical aspects of mineral recovery from the nearshore and deep ocean environments with a strong bias for the OBD toward industrial and international cooperative programs in the Pacific Basin and Rim. In terms of resource development, the marine minerals in the Pacific Basin may be favored in some cases, in competition with land sources, by political and environmental considerations.

Jan 1, 1990

By Bicer N

Current problems in predicting sub-surface strata movement and fracture development due to longwall mining have highlighted the need for more accurate, dependable methods of physical modelling of rock mechanics problems which are beyond the capabilities of current mathematical techniques. Physical model studies of the caved zone above the working faces up to the base of a water source are of importance in attempting to understand changes in mass permeability due to induced fracture zones and the resulting ground water conditions. Turkey's most important supplies of coking coals are to be found within the hard coal resources of the Black Sea coast. Coal seams up to 9 metres thick, dipping at angles as steep as 90 degrees are being successfully mined at the Kozlu Mine. Since 1956, mining operations have been carried out under the sea in dry conditions. The undersea mining conditions of the Kozlu Mine have been investigated using scaled physical models constructed from artificial materials which satisfied necessary scaling requirements. Models representing the in-situ conditions were tested and the following extraction sequence was employed: 1. The Sulu Seam extraction 2. The Acilik Seam extraction (as two slices) 3. The Piric Seam extraction. The displacement of the fixed reference points were subsequently measured using a high precision photogrammetric technique and induced horizontal and vertical strains were calculated.

Jan 1, 1988

By K B. Barnard, M D. Urbani

A synergistic solvent extraction (SX) system for nickel and cobalt recovery using Versatic 10 and decyl-4-pyridinecarboxylate was tested with BHP Billiton pilot plant leach solution. Another synergistic SX system for cobalt and zinc recovery was successfully tested using Baja MiningÆs pilot plant leach solutions. Synergistic SX systems have also been developed to separate iron, zinc and copper from nickel and cobalt for Minara Resources and to separate manganese from magnesium and calcium in waste stream for HiTec Energy. The gypsum precipitation problem at the former Bulong operation could have been alleviated using a Versatic 10 and CLX50 synergistic SX system. These synergistic systems have shown high selectivity for target metals over impurity metals and would largely improve SX plant operation. Maintaining a æhealthyÆ organic is very important for efficient plant operation. Careful analysis of plant organic at CSIRO has been used as a tool to pre-empt and/or solve problems in operating circuits. Work performed to assist operators has included assessing plant organic solutions to highlight impurity build-up with time, assessing reagent stability under prescribed operating conditions, correlating organic composition with impurity transfer and crud analysis. An independent estimate has determined that work in this area by CSIRO has provided over $50 M in benefits to the industry.

Jan 1, 2005

By P Jago

KCGMÆs Fimiston Open Pit, located in the centre of the historic Golden Mile, is situated above some 3000 kilometres of old underground workings. These workings, both level and vertical, present significant safety and operational problems in the pit. One of these challenges is in safely drilling void areas so that they can be charged and blasted effectively. Current drilling practices in these areas require machines that can only drill 115 mm holes on a smaller pattern than the standard blast pattern. This results in more time and cost to both drill and charge these areas. Any other method currently available to drill out these areas involves putting operators in a potentially hazardous situation by being too close to the void area being drilled. Not effectively drilling and blasting these areas leads to hazardous situations further in the mining cycle including oversize, large toe and uncollapsed voids. Ineffective blasting also causes reductions in mining productivity and mine to mill performance. In response to these issues, KCGM has commissioned the implementation of a fully remote controlled DM45 blast hole drill rig to drill out selected void areas. The remote system, installed in conjunction with Ausdrill Ltd and GM Mining Electrics, is designed to operate similarly to a tele-remote bogging system with the operator controlling the drill rig from a separate control cabin via radio signals and video feed. This allows KCGM to drill in areas of higher risk without exposing the operators to voids. The drill rig will also be able to drill standard patterns through some specially selected void areas, reducing costs and extra time associated with drilling and charging void affected areas. The remote rig is expected to provide a number of benefits, both in the drilling process and in further downstream operations. Costs of drilling in void areas are expected to decrease with standard patterns instead of smaller patterns being drilled. Safety and operator comfort are also expected to increase through removing the operator from the pit floor. Blasting is also expected to see significant improvements through increased ease of charging void areas (because of larger holes and standard patterns), more consistent patterns resulting in less secondary blasting and toe and an overall improvement in the speed and cost of charge-up practices. This more consistent blasting will also improve shovel productivity, crusher performance and overall mine-to-mill efficiency. This paper presents an overview of the development of the remote controlled system, including modifications that have occurred since commissioning. It explains some of the problems encountered and how these have been solved. Key issues for operational success will be identified and explained with a view to making future implementations easier. Factors used to assess the performance of the remote controlled rig will also be explained in further detail and used in a preliminary assessment of the rigÆs feasibility.

Jan 1, 2003

Computers represent substantial capital investment. A better return on that invest- ment comes from more effective use of the computer's facilities. By using Telecom's data communications facilities, more people in more locations can have ready access to those facilities.

Jan 1, 1983

By Evans A, Jones O

Surface subsidence resulting from "total extraction" of coal in the Collie Basin first occured in 1987 when Western Collieries Ltd trialled the Wongawilli mining method. Because very little quantitative subsidence data existed for the weak, Permian sediments, a research program was set up prior to the extraction of the first panel. The objective of the study was to be able to predict subsidence characteristics and effects prior to mining future total extraction panels. Attempts at predicting subsidence began using existing subsidence models from other coal mining regions, however, as more site information became available, it became clear that it was necessary to develop a separate, she specific predictive model for the Collie Coal Basin. Analysis of extensive field monitoring data for both surface and subsurface subsidence has produced a series of empirical models which can predict the shape of surface subsidence troughs and corresponding tilts, and strains for rectangular panels and describe the sequences of ground movement from the mine roof through to the ground surface.

Jan 1, 1992

By Gostylla W

The economic feasibility of controlled district cross-cut recirculation is examined in this paper with particular reference to the most important mine ventilation network parameters. An algorithm is developed to express the annual cost of recirculation which is then compared to the annual cost of conventional ventilation using the University of Queensland Experimental Mine as a case study. The concepts of resistance ratio and volumetric efficiency ratio are introduced and used to analyse the economic feasibility of controlled recirculation within a mine ventilation network.

Jan 1, 1988

By Grouhel P

Blasting performance is directly related to the characteristics and efficiency of the explosives used. The selection of the correct explosive for particular blast conditions and objectives depends on the ability to characterise the performance of individual explosive products. Techniques have been developed by the JKMRC to measure explosive performance and assess the impact of explosive performance on blast results. Studies conducted at a number of mine sites have shown that different types of explosives perform quite differently and that the performance of any particular explosive can vary significantly. The principal causes of these variations have been identified and detailed blast monitoring techniques, including the analysis of muckpile fragmentation and shape, have been used to quantify the effects of explosive performance on blast Results.

Jan 1, 1990

By P Mackenzie, S Askraba

Pyritic black shales present several challenges to mining operations due to their reactivity. The risk of predetonation of explosives in blastholes, spontaneous combustion of fractured rock and the generation of acid rock drainage must be managed for safety, operational and environmental reasons. At the Mt Tom Price iron ore mine there is a need to differentiate between reactive and non-reactive shale in order to assess risk and make decisions on materials handling. The current approach uses a combination of stratigraphic information and sulfur analysis of blasthole samples. The time taken for sulfur analyses can be a constraining factor on mine production. A new instrument developed by ANSTO Minerals overcomes some of the current limitations on material characterisation. The IOR MeterÖ measures the intrinsic oxidation rate (IOR) of samples of broken rock by circulating air through a sample and monitoring the oxygen concentration over time. The intrinsic oxidation rate is given by the rate at which oxygen is consumed per unit mass of sample, in units of kg(oxygen) kg-1(sample) s-1. Up to eight samples can be measured simultaneously and the turn-around time can be less than 12 hours. Initial trials of the IOR MeterÖ were undertaken at the Mt Tom Price mine in July 2004. The measured IOR of samples from a blasthole pattern spanning different geological layers containing black shale, correlated strongly with the expected reactivity of those layers. The correlation between position in the geological sequence (detailed stratigraphy) and IOR MeterÖ results were much stronger than that between stratigraphy and sulfur content. The new characterisation technique offers the prospect of improving the ability to identify and predict the behaviour of reactive black shales and to differentiate more precisely between different materials. Mine planning, operations, safety and environment all stand to benefit from the success of further trials of the technique.

Jan 1, 2005

By Jackson D. G

Iron ore mineralisation in the Paraburdoo environs is known to extend almost continuously over a strike length of 55 kilometres. Six formations of the Mount Bruce Supergroup con- tain high grade mineralisation in varying degrees of importance. Ore is currently being mined from the Joffre and Dales Gorge Members of the Brockman Iron Formation, with smaller, less significant amounts, occasionally taken from the lowermost units of the Weeli Wolli Formation and the upper parts of the Mount McRae Shale. Regional mapping has demonstrated the existance locally of a major unconformity at the base of the Wyloo Group sediments out- cropping south of the minesite. The basal con- glomerates at the unconformity are sometimes mineralised at Paraburdoo. A supergene enrich- ment process controlled by structure, strati- graphy and topography is the only one which can satisfactorily explain the disposition and chemistry of the Paraburdoo iron orebodies.

Jan 1, 1979

Renison Limited produces high and low grade tin concentrates at an annual rate of 5000 tonnes of contained tin metal. In spite of the fine average cassiterite grain size, emphasis is placed on gravity concentration methods to produce a high grade final product. Cassiterite flotation is considered and operated as a gravity circuit scavenger responsible for approximately 15 percent of recovered tin metal as a fine grained low grade concentrate. Metallurgical problems mainly result from ore-type variations which may be aggravated by a number of circulating loads. The rationalisation of circuitry is being studied to provide more effective control by operators and to allow exploitation of current control and modelling techniques.

Jan 1, 1977

By Till M, McGee WA

The Hermit Islands are situated at 145¦ E 1 30'S in the Bismarck Sea approximately 200km WNW of Manus Island. They are dominated by basalt flows, one of which yielded a K/Ar isotopic date of 3.4 + 0.05Ma. All basalts examined were olivine-bearing, but one sample also contained hornblende. Although many outcrops were weathered, no evidence of pervasive hydrothermal alteration was observed on any islands and non-weathered rocks are petrographically fresh and many retain glass.

Jan 1, 1990

Although a formal EES was not prepared for the WIM project due it winding down, CRA Ltd has been through the EES and planning scheme amendment process for its demonstration plant. Community consultation was involved with all aspects of this process. The paper outlines the WIM EES consultation program and provides lessons for future community consultation for major projects in regional locations with significant potential to alter the environment.

Jan 1, 1992