Search Documents

Looking back 25 years, the role of the drill and blast engineer in an Australian mine seemed relatively simple, with the primary focal points being scheduling of the drill rigs, oversize control, and budget control with respect to consumption of both explosives and drill consumables. The choice of explosive selection was relatively simple, though many mines were becoming involved in trials of slurry explosives, emulsion blends, and low density ANFO blends. Guidelines to assist the engineer towards specific fragmentation targets were scarce, environmental constraints were light, and computers were rarely found on the desks of any mining engineers. Wall control blasting was in its infancy, with the bulk of attention being given to appropriate slope design and little real attention given to factors such as explosive distribution, and optimum delay timing and sequencing. Quantitative measurement of blasting performance was rare. The science of blasting, for fragmentation control, wall control, and environmental impact control was about to be born, and was heralded in those years by intense efforts by the explosive manufacturers and a proliferation of research centres throughout the world. Since the early 1980s, the role of the Australian drill and blast engineer has gone through a major metamorphosis, and currently requires a greater depth of scientific understanding than any other specialisation within mining engineering.

Jan 1, 2004

By Wiltshire PG

The process uses sodium hydroxide and sodium nitrate reagents as in conventional Harris refining plants, selectively removing the arsenic to the caustic phase at an operating temperature of 420-450¦C. A novel feature of the process concept is continuous treatment of loaded caustic slag for recovery of arsenic as a sandy crystal product suitable for further processing to arsenic trioxide. A large pilot plant was constructed and operated over a period of 3 years to develop materials handling techniques and equipment components and to prove the concept. Stable operations were achieved at equivalent capacities of 200 tonne/yr arsenic removal. The process is being considered in plans for expansion of bullion softening capacity at Port Pirie.

Jan 1, 1984

By Chen J, Zhu D

A detailed study on oil agglomeration of fine metal oxide particles is presented in this paper. The major content embraces several aspects which may possibly reflect the current trends in oil agglomeration such as the effect of chemical and physical parameters, the activation of target minerals and the deactivation of gangue particles, the mechanisim of bridging liquid and the kinetics of oil agglomeration process. Systems of ilmenite-feldspar, manganese dioxide - quartz were seperated successfully through oil agglomeration followed by decantation or flotation technique respectively. A triple mixture of vandium-bearing titanomagnetite ilmenite and feldspar was processed satisfactorily using a composite technology: oil agglomeration-decantation-magnetic concentration.

Jan 1, 1993

By A Buckingham, R M. Hancock

The underground Sunrise Dam gold mine commenced in October 2003 to extract ore from a series of orebodies with various dips, widths, and ore grades over a strike length of 1.5 km. To successfully operate flat stopes it was identified that a means to extract ore left behind after blasting in stopes with dips ranging from 15 to 40 degrees was needed. Various options were available, which included a bulk water cannon, hand held high-pressure water jet, remote controlled small dozer, several mini excavators and finally a specialised remote controlled excavator from the demolition industry. Trials were commenced for the bulk water cannon option in 2006 that proved that the concept worked, however, the system was too cumbersome to set up for use in cycle with production. Hand washing down using mine (low pressure) water with a two-inch bullhose proved of limited value. The small, one metre high remote controlled dozer as used in South Africa was reviewed, but the steepness of most of the stopes precluded this machine. The hand held high-pressure water jet option is still being investigated; with safety factors still being addressed. Several mini excavators were trialled to clean out the flat stopes with generally poor results, the machines being either too large to fit in the drives and pull ore down or too small with too short reach to effectively and efficiently pull ore out of the stope. In early 2007 a Brokk 330 remote controlled excavator was trialled on site with the low profile of the machine and unique arm configuration proving an effective tool for pulling ore from the footwall of short, flat stopes. A Brokk 330 remote controlled excavator was purchased in late 2007 and is currently in operation.

Jan 1, 2008

By R M. Briggs, I E. Smith, P M. Black, A B, R L. Brathwaite, J L. Mauk

The Hauraki Volcanic Region of the North Island developed between 18 and 1.9 Ma. Initial andesitic volcanism from 18 to 12 Ma was followed by 12 to 1.9 Ma volcanic activity that included rhyolitic, dacitic, andesitic, and basaltic compositions, with a gradual migration of activity to the SSE. Early andesitic volcanism evolved over the course of 8 m.y. to more silicic compositions; this trend was reset and repeated by post-10 Ma andesitic volcanism. Early and later andesites are otherwise remarkably similar in trace element composition. Rhyolites have the most diverse compositions, suggesting a major role for crustal input in their formation.

Jan 1, 2007

A methodology is described to integrate heap leaching into a CIP operation. The paper firstly describes what is meant by a 'systems approach'. A broad view of the objectives of integration of heap leaching into CIP is given, followed by the components of the system, and then a description of the methodology for integration. The seven stages of integration are given as determination of distribution of gold, sampling, metallurgical testwork, conceptual study, pilot heap operation, pit modelling and pit optimisation. The final result is a series of optimised curves which determine the maximum value of the orebody, and the optimum cut-over grade from CIP to heap leaching.

Jan 1, 1992

Since the mid-1970s there has been increasing attention in the South Pacific area to the problems of disaster planning and management at various levels, mainly from regional through national to provincial levels. This concern has been expressed in a variety of ways. International aid donors have made their views known in commentaries or reports. Seminar discussions have been organised at the regional level (such as at Suva, 1976; Suva, 1979; Tonga, 1982 and Suva, 1983). In-country training workshops or meetings have been organised (such as the "Disaster Preparedness Workshops for Non-governmental Organisations" in Pacific countries, jointly run by the Australian Red Cross and the Australian Overseas Disaster Response Organisation and supported by AIDAB, in Vanuatu, 1985; Solomon Islands, 1985; Western Samoa, 1986; Fiji, 1987; Tonga, 1987; Lae and Port Moresby, Papua New Guinea, 1988) or held outside the area (ACDC at Macedon, 1981). Training and/or research institutions have been established such as the East-West Center, Honolulu, and the Asian Disaster Preparedness Center, Bangkok (more Asia oriented). As part of the East-West Center Pacific Islands Development Program's Disaster Preparedness Project, a detailed manual of disaster preparedness and response procedures and guidelines has been published (Carter, 1984).Table 1 and figure 1 show that the area with which this discussion deals is a highly fragmented island region, comprising many small, some minute, nations, both in land area and population. The social structure is predominantly rural, with the capital city often making up a small part of the total population and, in absolute terms, little more than a small town. Outside the administrative and governmental activities concentrated in the capitals, in most cases the indigenous inhabitants depend on subsistence agriculture or on usually a monocultural concentration on a cash crop, most frequently coconuts.

Jan 1, 1990

By Ormsby W, Peters M, Van Gils H, Kehprens P, De Boorder H

The northern margin of the Arunta Block is characterized by a metasedimentary and volcanic sequence of lower metamorphic grade than that of the central Arunta Block. Whereas the Harts Ranges have granulite to amphibolite metamor- phic grades, the northern margin only reached greenschist to lower amphibolite facies. Most of the high grade area of the central Arunta Block appears to be unprospective, but the lower grade marginal fringe contains most mineral pros- pects to name a few: Barrow Creek, Molyhill and the Jervois Mine. Numerous smaller prospects occur in this marginal zone. Four major lithostratigraphic units can be recognized in the Jervois Mine area: 1. Gneissic Suite consisting of granitic and rhyolitic gneisses which are characterized by a distinct intersection lineation. 2. Metasedimentary Suite of cordierite- biotite schists and chlorite-biotite schists. 3. Mine Sequence, consisting of spotted schists with andalusite and cordierite, quartz- sericite-feldspar schists with distinct rhyo- litic remnants and quartz-sericite-feldspar schists which contain the lode horizons:

Jan 1, 1984

By D Morris

This presentation discusses a water filtration technology termed Fabric Media that is somewhat novel to the Australian market place and reports several recent mining industry installations. Like many novel household cleaning products, the Fabric Media technology applies the science of active washable micro fibres as the means of capturing contaminant solid particles. The simple Fabric Media water filtration product offers several attractive attributes when compared to the more traditional media bed filtration processes such as sand filters, and barrier filters such as micro membranes. A micro fibre based filtration media enables both superior adsorption for the contaminant and wash ability. Stronger adsorption capture enables a much higher flux and greater solids loading density for the filtration task, meaning that lower cost and smaller footprint equipment is available. For Fabric Media water filters, a textile weave is selected that minimises the flow backpressure for a given particle size separation. Thus for an equivalent filtration performance this provides a much lower operating energy requirement, generally between 50 and 80 per cent less than for a sand filter. A Fabric Media is not abrasive to itself or to the filter tank. The filtration performance remains constant and predictable. The equipment life is much longer and the asset value of the new filtration equipment should maintain throughout the project life. Fibres are extremely mechanically robust and chemically inert. Fabric Media survives repetitive exposure to a rapid mechanical washing event providing high wash efficiency with minimum equipment off-line time for the backwash. Dislodging captured contaminants by a high-speed mechanical agitation enables a minimum off-line time during backwash events. The vigorous backwash destroys adhering flocculant and eliminates the formation of mud balls, which can permanently foul sand filters. The mechanical agitation wash of the Fabric Media water filter ensures complete removal of grease and biofilm, which can adhere and block a membrane surface. In comparison to sand filters and micro filtration membranes, the Fabric Media product is applicable to a significantly wider range of solids concentrations without permanent damage. The technology is very forgiving to excursion in plant control and is therefore considered a very operator-friendly concept.

Jan 1, 2006

By Mortensen JK, Lang JR

The Canadian Cordillera contains numerous classic porphyry deposits and several unusual subtypes, including the alkaline suite of porphyry Cu-Au deposits and the Tombstone magmatic suite and associated Au¦W deposits. The alkaline suite formed in collisional settings in island arcs whereas the Tombstone suite was emplaced in an active fold and thrust belt in a continental arc. In addtion to different regional settings, these suites differ in the type of underlying basement, metallogeny, and the styles of mineralization. Both magmatic suites were emplaced over short intervals, probably in response to specific tectonic events. In the case of the alkaline suite, the tectonic event promoted magmatic processes suitable for the formation of porphyry Cu-Au deposits. The tectonic environment is less well constrained for the Tombstone suite, but the result was the formation of distinctive porphyry and intrusion-related Au¦W deposits.

Jan 1, 1995

By Savidis G

The characteristics of 'Z' (Back-over run) and 'R' (Reverse) ventilation systems are dis- cussed in relation to their suitability for longwall mining. Experience in European mines has been described as a basis for comparison with Australian conditions. In assessing the merits of each ventilat- ion system, such factors as longwall layout (pillar design, number of headings and gateroad stability), the need for gas drainage and bleed- er systems, as well as the influence of seam dip have been considered relevant. The R system is generally applicable for single and two heading development in seams where gas emission is a less serious problem. In contrast, the lower extraction to development ratio of the Z system (which arises from using three or more heading layouts) is considered more favourable where high gas emission occurs. The Z system provides greater flexibility with respect to the provision of refreshing air at the tailgate end, access of men and materials, installation and retrieval of gas drainage systems and the ability to interchange main- gate and tailgate roadways in cases where roof strata loads are difficult to control, or where cpam in hac an influrnra

Jan 1, 1983

By King D, Dickinson S. B, Matheson R. S

Graham Hall and V. M. Cottle (Rosebery, Tas.) : In their paper on "The Mineralized Rift Valleys of Tasmania", Campana, Dickinson, King and Matheson have summarized a wealth of data from many sources. In proposing the new concept of a rift valley structure, they claim to have found a new guide to regional ore control and distribution in North-west Tasmania.Although the authors acknowledge suggestions made by us prior to publication of the pa:per, we are still at variance with their conclusions. We are not convinced that a rift valley structure exist~d when the Ordovician conglomerate was deposited. We are unable to find evidence for Cambrian deposition in a rift valley or reason to project the structure to embrace Hercules, Rosebery, and "possibly" Mt Bischoff.That the Great Lyell Fault (the authors' Owen Rift Fault) is a promising place to look for ore is not a new idea, but the existence of important ore deposits away from the structure reveals its inability to provide an adequate explanation of regional mineral distribution. A well-known structure that does have an influence on ore deposition is not discussed by the authors.STRUCTURAL CONSIDERATIONSThe great thickness of coarse unsorted Ordovician conglomerate lying in an elongate but narrow belt of country is presented as evidence of its deposition centrally within a rift valley, the position-of which is now said to be outlined by resistant slabs of the conglomerate. The marginal shears of the rift are said to show up well along the edges of the conglomerate.

Jan 1, 1959

The operators of the iron ore railroads in the Pilbara faced problems of excessive wear between rail and wheels as the tonnage hauled increased in the early 1970's. Joint research projects were begun between Hamersley Iron, Mt Newman Mining and the BHP Melbourne Research Laboratories to study these problems and recommend solutions. The particular problems of wheel rail interaction were solved by asymmetrical profile grinding of the rail and modifications to the machining of the wheels. Rail materials were improved through increasing yield strengths by alloying and by heat treatment. Wheel materials were improved by alloying. The economic benefits of these improvements have been demonstrated by much reduced re-rail requirements and other reduced maintenance costs.

Jan 1, 1986

By Graham JW, Cullen GV

edicted increase in, Aluminium production and the possibility of a diminishing supply of petroleum coke for anode electrodes in alumina reduction cells makes it desirable to find alternative electrode materials. Brown coal char, with a lower ash content and with an elemental purity similar to petroleum coke, has been produced by leaching in hydrochloric acid, washing with water and charring at 115000. The cost of processing is estimated to be competitive with petroleum coke. Without further processing the bulk density and real density were undesirably low, but. by briquetting the coal before charring and crushing, the bulk density was improved to 92 per cent of the petroleum coke value and the Particle density was improved to 92 per cent of the density of petroleum coke by water-displacement or 75 per cent by mercury displacement. Pre-baked electrodes were prepared from the char alone, mixtures of petroleum coke and char and from petroleum coke alone, all bonded with coal tar pitch. The electrodes were tested for the usual physical properties and were, evaluated for performance in a laboratory size alumina reduction cell. Electrodes based on brown coal char alone were found to be inferior in physical properties, and performance, but mixtures of the char and petroleum coke, despite poorer density, electrical resistivity and carbon consumption on a theoretical basis, in performance tests gave up to 17 per cent better carbon consumption per weight of aluminium produced and 21 percent better electrical current efficiency than the electrodes based on petroleum coke alone. It is suggested that larger scale tests are warranted.

Jan 1, 1970

Martin Mining and Tunnelling Pty Ltd is a mining contractor with offices in Kalgoorlie, WA, Australia and Timmins, Ontario, Canada.Martin Mining and Tunnelling Pty Ltd offers services in mine contracting which include shaft raising, raise enlarging, excavation of rock passes and ventilating systems. It also offers the mining industry a unique mining method using the Alimak raise climber system.The Alimak raise climber system may be utilised in various types of orebodies, as the system is flexible to change. Sloping widths, drill hole patterns and changes in dip can all be accommodated with this method.This system allows for a highly productive, cost-efficient alternative to conventional longholing methods. This paper will focus on various aspects of the Alimak system which inherently make it a safe, viable method of ore extraction.

Jan 1, 1993

This paper addresses; land use, rehabilitation and the State/Federal regulatory process, in light of Australia signing various international conventions and agreements in the area of environmental protection. The conventions on biological diversity, climate change and the implications of the Rio and Agenda 21 declarations are examined. The implementation of these initiatives through the Inter-Governmental Agreement on the Environment, and through legistlative mechanisms at Federal and State level is explored.Particular attention is given to the biodiversity strategy in context of the need to integrate economic aspirations and environmental concerns as a basis for sustsainable development. The paper concludes with a brief comparison of the major approval processes in each State, relating to mining environmental issues.

Jan 1, 1992

By M Simanjuntak, A M. Supomo

PT Freeport IndonesiaÆs copper/gold operation disposes of approximately 222 000 dry metric tonnes of tailings per day via two thickeners. Reduction of the flocculant dosage rates in each of the tailing thickeners has been achieved with the installation of Clarometers«, modifications to the existing operating DCS control strategy and a change in plant flocculant. This has reduced the flocculant consumption rate in the last twelve months by approximately 20 per cent. It has also highlighted the disparity in the settling rates of the two thickeners. Collaborative efforts between Cytec technical site engineers and Freeport operational personnel have made possible the overall gains achieved in the tailings thickener optimisation.

Jan 1, 2003

Cannington is a Broken Hill type deposit discovered by BHP Minerals, now BHP Billiton, in 1990. The deposit is located south east of Cloncurry, Queensland, Australia. The deposit occurs in the Eastern succession of the Mount Isa Inlier within the Soldiers Cap Group. The mineralisation is interpreted to be confined to two limbs of a synform wrapped around a core amphibolite. The silver, lead and zinc mineralisation is zoned within silicic and mafic units. There is a strong association between silver and lead. The combination of mafic and silicic zoning, differing relative grades of silver, lead, zinc and iron, the relative position of the mineralisation on the synform limbs and differing metallurgical performances have resulted in the identification of ten different ore types, four of which are currently extracted. Ordinary Kriging (OK) is used as the resource estimation methodology for the silver, lead and zinc mineralisation. This modelling approach has performed quite well for resource reporting and long term mine planning. However the limitations of this modelling technique to adequately provide information on a local stope scale has lead to the geological staff to consider alternatives to this approach. Limitations of the current modelling method apply to both the geometry of the orebodies and the grade variability. Since early-2000 the Cannington geologists have been experimenting with modelling both the distribution of the mineralisation types using Probability Field conditional simulation (PF) and the distribution of grade using Sequential Gaussian Simulation (SGS). This approach to local modelling of mineralisation type and metal grades using conditional simulation (CS) has undergone a full evaluation by comparing grades estimated for stopes using both the (OK) resource model and conditional simulation (CS) models. The mine planning staff have used the CS derived models, and have found improvements in grade predictions over the currently utilised Ordinary Kriging û derived resource model.

Jan 1, 2003

Laboratory scale simulation experiments show that the adsorption capacity of Au(CN)Z- on activated carbon in the presence of organic plant contaminants is dependent on the particle size of the carbon. This observation suggests that fine carbon in a CIP contactor can protect coarse CIP carbon from fouling in a dirty CIP plant. A preliminary test of this concept was made using fine lignite coal as the organic scavenger in the presence of the CIP carbon Calgon GRC22 in an alkaline cyanide solution containing Teric 401, sodium ethyl xanthate and kerosene.

Jan 1, 1991

By Granholm S

The current emphasis within the mining industry to reduce the cost of production has stimulated interest in the field of maintenance and operational reliability of capital intensive mining equipuent. The failure consequences of these machines have major safety and economic implications for a mine operator. The reliability centered maintenance (RCM) approach has been found cost effective for equipment maintenance and for achieving high level system perform- ance by many organizations such as airline, military, chemical, process and manufac- turing industries. In this paper an attempt has been made to describe in brief the basic concepts of a RCM approach, the methods of RCM analysis and its cost effectiveness for maintenance of equipment. Since this approach is comparatively new for the mining industry, suitable examples are given to illustrate the case.

Jan 1, 1988